The Role of Oxygen during Thermal Reduction of Graphene Oxide Studied by Infrared Absorption Spectroscopy

Similar documents
The role of intercalated water in multilayered. graphene oxide

Resistive switching behavior of reduced graphene oxide memory cells for low power nonvolatile device application

Supporting Information. for. Angew. Chem. Int. Ed. Z Wiley-VCH 2003

SUPPLEMENTARY INFORMATION

Supplementary Information

ORGANIC - BROWN 8E CH INFRARED SPECTROSCOPY.

Lecture 11. IR Theory. Next Class: Lecture Problem 4 due Thin-Layer Chromatography

Band-like transport in highly crystalline graphene films from

Infrared Spectroscopy

Supporting Information Hydrothermal synthesis of nitrogen-doped graphene hydrogels using amino acids with different acidities as doping agents

Supporting information. Infrared Characterization of Interfacial Si-O Bond Formation on Silanized. Flat SiO 2 /Si Surfaces

Supporting Information. Hydroxyl Radical Attack on Reduced Graphene Oxide

Supporting Information

Journal Name. Supporting Information. Significant enhancement in blue emission and electrical conductivity of N-doped graphene. Dynamic Article Links

Supplementary Figure S1 Images of the catalytically active ba-go. (a) Images of the exfoliated-go suspension (~0.6mg ml -1 ). 1: before base-treating

Photocatalytic degradation of dyes over graphene-gold nanocomposites under visible light irradiation

How to Interpret an Infrared (IR) Spectrum

1 Which of the following cannot be used to detect alcohol in a breathalyser test? Fractional distillation. Fuel cell. Infrared spectroscopy

Electronic Supplementary Information

SPECTROSCOPY MEASURES THE INTERACTION BETWEEN LIGHT AND MATTER

Influence of temperature and voltage on electrochemical reduction of graphene oxide

Supplementary Information

CHEM 3.2 (AS91388) 3 credits. Demonstrate understanding of spectroscopic data in chemistry

Química Orgânica I. Ciências Farmacêuticas Bioquímica Química. IR spectroscopy AFB QO I 2007/08 1 AFB QO I 2007/08 2

Supporting Information

Functionalization of reduced graphene oxides by redox-active ionic liquids for energy storage

Room-temperature metastability of multilayer graphene oxide films

Chemistry 2. Assumed knowledge

ORGANIC - BRUICE 8E CH MASS SPECT AND INFRARED SPECTROSCOPY

Infrared Spectroscopy An Instrumental Method for Detecting Functional Groups

Solar desalination coupled with water remediation and molecular hydrogen production: A novel solar water-energy nexus

Understanding Aqueous Dispersibility of Graphene Oxide and Reduced Graphene Oxide through pka Measurements

C h a p t e r F o u r t e e n: Structure Determination: Mass Spectrometry and Infrared Spectroscopy

Fourier Transform Infrared Spectrophotometry Studies of Chromium Trioxide-Phthalic Acid Complexes

Supplementary Information for. Origin of New Broad Raman D and G Peaks in Annealed Graphene

Infrared Spectroscopy. Provides information about the vibraions of functional groups in a molecule

Electronic Supplementary Information. Experimental details graphene synthesis

Probing Bonding Using Infrared Spectroscopy Chem

Supporting Information. Effects of Environmental Water Absorption by. Film Transistor Performance and Mobility

S1. X-ray photoelectron spectroscopy (XPS) survey spectrum of

Functional Group Adsorption on Calcite: I. Oxygen Containing and Nonpolar Organic Molecules

Chapter 12 Mass Spectrometry and Infrared Spectroscopy

Organic Compound Identification Using Infrared Spectroscopy. Description

Radiant energy is proportional to its frequency (cycles/s = Hz) as a wave (Amplitude is its height) Different types are classified by frequency or

Effect of Electric Field on Condensed-Phase Molecular Systems. II. Stark Effect on the Hydroxyl Stretch Vibration of Ice

SUPPLEMENTARY INFORMATION

Structure Determination. How to determine what compound that you have? One way to determine compound is to get an elemental analysis

Lecture 8. Assumed knowledge

Introduction. The analysis of the outcome of a reaction requires that we know the full structure of the products as well as the reactants

Supplementary Figure S1. AFM characterizations and topographical defects of h- BN films on silica substrates. (a) (c) show the AFM height

Supplementary Information for

Infrared Spectroscopy

Asymmetry of Peaks in the XPS of Polymers

Organic Spectra Infra Red Spectroscopy H. D. Roth. THEORY and INTERPRETATION of ORGANIC SPECTRA H. D. Roth. Infra Red Spectroscopy

Supplementary Information

Supporting Information

Supplementary Information. Experimental Evidence of Exciton Capture by Mid-Gap Defects in CVD. Grown Monolayer MoSe2

A Biosensor for the Detection of Single Base Mismatches in microrna

Advanced Pharmaceutical Analysis

Chemical functionalization of graphene sheets by solvothermal reduction of suspension of

Transparent Electrode Applications

Infrared Spectroscopy: Identification of Unknown Substances

MOLECULAR REPRESENTATIONS AND INFRARED SPECTROSCOPY

Infrared Spectroscopy

Surface Defects on Natural MoS 2

SUPPLEMENTARY INFORMATION

Real-Time Structural Evolution at the Interface of an. Organic Transistor During Thermal Annealing

Table 8.2 Detailed Table of Characteristic Infrared Absorption Frequencies

PHYSICAL AND CHEMICAL PROPERTIES OF ATMOSPHERIC PRESSURE PLASMA POLYMER FILMS

Supporting information

SUPPLEMENTARY INFORMATION

CHE 325 SPECTROSCOPY (A) CHAP 13A ASSIGN CH 2 CH CH 2 CH CHCH 3

Magnetite decorated graphite nanoplatelets as cost effective CO 2 adsorbent

Bandgap engineering through nanocrystalline magnetic alloy grafting on. graphene

Supporting Data. The University of Texas at Dallas, 800 West Campbell Road, Richardson, Texas 75080, United

doi: /

Supplementary Materials

Supplementary Information for. Silver Nanoparticles Embedded Anti-microbial Paints Based on Vegetable Oil

Supporting Information

7a. Structure Elucidation: IR and 13 C-NMR Spectroscopies (text , , 12.10)

Restoring the electrical conductivity of graphene oxide films by UV light induced. oxygen desorption

Supplementary Figure 1 XRD and Raman spectrum characterization of GQDs. a, XRD pattern of GQDs. b, Raman spectrum of GQDs, the appearance of the mode

Supplementary Information

Vertical Alignment of Reduced Graphene Oxide/Fe-oxide Hybrids Using the Magneto-Evaporation Method

MASS and INFRA RED SPECTROSCOPY

analysis. Figure S1(a-c), shows C-1s XPS of powder graphite, polymer coated graphene oxide (GO) and

Surface Hydrophilic Treatment of Polyester Films via UV irradiation

Infrared Characteristic Group Frequencies

a b c Supplementary Figure S1

Fabrication of graphene quantum dot-decorated graphene sheets via. chemical surface modification

Supporting Information

Characterization of Secondary Emission Materials for Micro-Channel Plates. S. Jokela, I. Veryovkin, A. Zinovev

Supplementary Information. Core-Shell Silver/Polymeric Nanoparticles-Based Combinatorial Therapy against Breast Cancer In-vitro

Acidic Water Monolayer on Ruthenium(0001)

12. Structure Determination: Mass Spectrometry and Infrared Spectroscopy

A high-pressure-induced dense CO overlayer on Pt(111) surface: A chemical analysis using in-situ near ambient pressure XPS

Optical Science of Nano-graphene (graphene oxide and graphene quantum dot) Introduction of optical properties of nano-carbon materials

Photocatalysis: semiconductor physics

CHM Salicylic Acid Properties (r16) 1/11

J. Price, 1,2 Y. Q. An, 1 M. C. Downer 1 1 The university of Texas at Austin, Department of Physics, Austin, TX

Transcription:

SUPPLEMENTARY INFORMATION The Role of Oxygen during Thermal Reduction of Graphene Oxide Studied by Infrared Absorption Spectroscopy Muge Acik, 1 Geunsik Lee, 1 Cecilia Mattevi, ǂ2 Adam Pirkle, 1 Robert M. Wallace, 1 Manish Chhowalla, 2 Kyeongjae Cho, 1 Yves Chabal* 1 1 Department of Materials Science and Engineering, University of Texas at Dallas, Richardson, TX 75080 2 Rutgers University, Materials Science and Engineering, Piscataway, NJ, USA 08854 ǂ Present address: Department of Materials, Imperial College, London, UK SW7 2AZ *Authors to whom correspondence should be addressed to: chabal@utdallas.edu 1

Absorbance (a. u.) ν (C-O-C) α β γ ν (C-O) ν (C=O) ν (COOH, C=O) ~1652 cm -1 ν (C-O-C) 8x10-4 ~1284 cm -1 ν (C=O) ~1735 cm -1 ν (C=C, C=O) ~1580 cm -1 ν (C-OH, COOH, H 2 O) ~ 3000-3700cm -1 GO (single layer) 800 1200 1600 3200 3600 Wavenumber (cm -1 ) Figure S1 Transmission infrared absorbance spectrum of GO (single layer) at room temperature. Vibrational modes are shown for hydroxyls (possible COOH and H 2 O contribution) (C-OH, 3000-3700 cm -1 ), ketones (C=O, ~1750-1850 cm -1 ), carboxyls (COOH and/or H 2 O) (~1600-1750 cm -1 ), sp 2 -hybridized C=C (in-plane stretching, ~1500-1600 cm -1 ), epoxides (C-O-C, ~1280-1330 cm -1 and 800-900 cm -1 ). The regions labeled as α- (red), β-(yellow), and γ-(green) refer to the chemical species summarized in Table S5 for the overlapped infrared frequencies at 800-1500 cm -1. 2

Absorbance (a. u.) ν (C-O-C) α β γ ν (C-O) ν (C=O) ν (C-O-C) ~1253 cm -1 ν (COOH, C=O) ~1653 cm -1 ν (C=O) ~1740 cm -1 ν (C=C, C=O) ~1590 cm -1 10-3 ν (C-OH, COOH, H 2 O) ~ 3000-3700cm -1 GO (three layers) 800 1200 1600 3200 3600 Wavenumber (cm -1 ) Figure S2 Transmission infrared absorbance spectrum of GO (three layers) at room temperature. Vibrational modes are shown for hydroxyls (possible COOH and H 2 O contribution) (C-OH, 3000-3600 cm -1 ), ketones (C=O, ~1750-1850 cm -1 ), carboxyls (COOH and/or H 2 O) (~1600-1750 cm -1 ), sp 2 -hybridized C=C (in-plane stretching, ~1500-1600 cm -1 ), epoxides (C-O-C, ~1280-1330 cm -1 and 800-900 cm -1 ). The regions labeled as α- (red), β-(yellow), and γ-(green) refer to the chemical species summarized in Table S5 for the overlapped infrared frequencies at 800-1500 cm -1. 3

Absorbance (a. u.) ν (C-O), ~ 800 cm -1 ν (C-O-C), ~850 cm -1 α β γ ν (C-O-C) ~1230 cm -1 ν (C-O) ~800-1330 cm -1 ν (C=C) ~1595 cm -1 ν (COOH) ~1725 cm -1 ν (C=O) ~1820 cm -1 ν (COOH, C-OH, H 2 O) ~3000-3700 cm -1 2 10-2 GO (multi layers) bulk 800 1200 1600 3000 3250 3500 3750 Wavenumber (cm -1 ) Figure S3 Transmission infrared absorbance spectrum of bulk GO (multi layers) at room temperature. Vibrational modes are shown for hydroxyls with contributions from COOH and H 2 O (C-OH, 3000-3700 cm -1 ), ketones and/or carboxyls within overlapped frequency range (C=O, COOH ~1700-1900 cm -1 ), sp 2 -hybridized C=C (in-plane stretching, ~1550-1650 cm -1 ), and epoxides (C-O-C, ~1350 cm -1 and 800-900 cm -1 ). The regions labeled as α- (red), β-(yellow), and γ-(green) refer to the chemical species summarized in Table S5 for the overlapped infrared frequencies at 800-1500 cm -1. 4

Table S1 Simulated infrared intensities and vibrational frequencies of (a) basal plane hydroxyls, (b) edge hydroxyls, (c) carboxyls, and (d) epoxides. 5

Table S2 Simulated infrared intensities and vibrational frequencies of (a) ketones, (b) 1,2benzoquinones, (c) 1,3-benzoquinones, (d) benzo[de]chromene-2,3-diones, and (e) acid anhydrides. 6

Table S3 Simulated infrared intensities and vibrational frequencies of (a) 2-pyranones (pyrones), (b) Naptho[1,8-de][1,3]dioxin-2-ones, (c) γ-butyrolactones, and (d) 5-membered-ring lactols. 7

Table S4 Simulated infrared intensities and vibrational frequencies of (a) ethers (pyran-like), (b) ethers (furan-like), (c) dioxolanes, and (d) peroxides. 8

Table S5 Summary of corrected frequencies extracted from the simulation frequencies for overlapped regions named as α (900-1100 cm -1 ), β (1100-1280 cm -1 ), and γ (1280-1500 cm -1 ) showing additional contributions of various chemical species 1. Overlapped Regions Chemical Species Corrected Frequencies (cm -1 ) α (900-1100 cm -1 ) 5-membered-ring lactol 1 peroxide 1 ether (furan) 1,3 dioxolane 1,2 basal plane hydroxyl 2 edge hydroxyl 2 naptho[1,8-de][1,3]dioxin-2-one 2 acid anhydride 4 carboxyl 3 epoxide 4 949 928 1003, 1065 1036, 1064 1075 1040, 1095 1073 996 1081 1070 β (1100-1280 cm -1 ) 2-pyranone (pyrone) 1 γ-butyrolactone 1 peroxide 1,2 ether (pyran) 2 ketone 2 benzo[de]chromene-2,3-dione 2 5-membered-ring lactol 2 acid anhydride 3 epoxide 3 ether (furan) 3 1,2-benzoquinone 3 1150 1197 1267, 1185 1103 1240 1159 1131 1132 1170 1279 1223 γ (1280-1500 cm -1 ) Ether (pyran) 1 epoxide 2 peroxide 2 ketone 1,3 1,3-benzoquinone 1,3 1322 1320 1267 1453, 1486 1476, 1523 1 Numbers correspond to the orders in terms of the simulated IR intensities (i. e. the strongest is 1, the weakest 4 ). 9

Table S6 Simulated infrared intensities and vibrational frequencies for nearby interacting oxygen groups (a) two COOH, (b) two OH, (c) one OH and a COOH, (d) two C=O, (e) an OH and a C=O, and (f) a COOH and a C=O. 10

Note on frequencies of Table S6-d: When ketones and OH groups are located nearby, the highest frequency is simulated as 1825 cm -1. This is because the neighboring OH bonds are coupled strongly to C=O groups with the bond lengths (1.20 and 1.23Å, respectively), which are very similar. For this reason, the original frequency goes down to almost half. Therefore, we are not able to show a C-OH contribution at ~3000-3700 cm -1. Table S7 Summary of corrected frequencies extracted from the simulation frequencies for overlapped regions named as α (900-1100 cm -1 ), β (1100-1280 cm -1 ), and γ (1280-1500 cm -1 ) showing additional contributions from neighboring oxygen groups 1. Overlapped Regions Neighboring Groups Corrected Frequencies (cm -1 ) α (900-1100 cm -1 ) β (1100-1280 cm -1 ) γ (1280-1500 cm -1 ) COOH + COOH OH + OH COOH + C=O OH + COOH OH + C=O OH + OH OH + C=O OH + OH 1095 3 1080 4 1064 4 1064 5 1172 1 1271 3 1365 5, 1463 3, 1485 5 1480 5 1 Numbers correspond to the orders in terms of the simulated IR intensities (i. e. the strongest is 1, the weakest 5 ). 11

Absorbance (a. u.) EDGE ν (-O-), ~800 cm -1 α β γ SiO 2 (TO) ν (Si-OH) SiO 2 (LO) ν (C=C) Leftover ν (C=O) 750 800 850 900 GO (five layers) (b) 850 C: 750 C FWHM: ~ 50 cm -1 (a) 750 C: 650 C 10-3 800 1200 1600 3000 3200 3400 3600 Wavenumber (cm -1 ) Figure S4 Tranmission infrared differential spectra of GO (five layers) at high temperature regime (650-850 C). Changes of functional groups are given at temperatures: (a) 750-650 C (black), and (b) 850-750 C (blue). A new peak appears at ~800 cm -1 after 850 C anneal with a fwhm of ~50 cm -1 indicated in the inset. The vibrational stretching mode of C=C is also shown at ~1595 cm -1. A loss corresponding to Si-OH was observed at ~980 cm -1. Vibrational modes of SiO 2 (LO and TO modes) appear at ~1250 and 1080 cm -1, respectively. 12

Absorbance (a. u.) EDGE ν (- O-), ~800 cm -1 α β γ SiO 2 (TO) ν (Si-OH) SiO 2 (LO) ν (C=C) Leftover ν (C=O) (b) 850 C: 750 C 750 800 850 900 950 (thin film) FWHM: ~ 44 cm -1 (a) 750 C: 650 C GO (multi layers) 5 10-3 800 1200 1600 3200 3600 Wavenumber (cm -1 ) Figure S5 Tranmission infrared differential spectra of GO (multi layers, thin) at high temperature regime (650-850 C). Changes of functional groups are given at temperatures: (a) 750-650 C (black), and (b) 850-750 C (green). A new peak appears at ~800 cm -1 after 850 C anneal with a fwhm of ~44 cm -1 indicated in the inset. The vibrational stretching mode of C=C is also shown at ~1595 cm -1. A loss corresponding to Si-OH was observed at ~980 cm -1. Vibrational modes of SiO 2 (LO and TO modes) appear at ~1250 and 1080 cm -1, respectively. 13

Absorbance (a. u.) (b) 850 C: 750 C EDGE ν (- O-), ~798 cm -1 FWHM: SiO ~ 32 cm -1 2 SiO 2 ν (C=C) (TO) ν (Si-OH) (LO) Leftover ν (C=O) 700 750 800 850 (Bulk Film) (a) 750 C: 650 C α GO (multi layers) 2x10-2 β γ 800 1200 1600 3200 3600 Wavenumber (cm -1 ) Figure S6 Tranmission infrared differential spectra of GO (multi layers, bulk) at high temperature regime (650-850 C). Changes of functional groups are given at temperatures: (a) 750-650 C (black), and (b) 850-750 C (brown). A new peak appears at ~800 cm -1 after 850 C anneal with a fwhm of ~32 cm -1 indicated in the inset. The vibrational stretching mode of C=C is also shown at ~1595 cm -1. A loss corresponding to Si-OH was observed at ~980 cm -1. Vibrational modes of SiO 2 (LO and TO modes) appear at ~1250 and 1080 cm -1, respectively. 14

Total Infrared Absorbance (cm -1 ) Normalized Absorbance 27 26 25 24 23 22 21 20 19 18 17 16 (i) std. ± 2 3% GO-5L (Sample-a) GO-5L (Sample-b) Incomplete Oxygen Removal 0 125 250 375 500 625 750 875 Annealing Temperature ( C) 1.18 (ii) 1.16 std. 2% 1.14 1.12 1.10 1.08 1.06 1.04 1.02 1.00 ~92 at. % 0.98 0.96 GO-5L (Sample-a) 0.94 0.92 GO-5L (Sample-b) 0 125 250 375 500 625 750 875 Annealing Temperature ( C) Figure S7 Integrated infrared absorbance of five layered GO for two different samples. Comparison of (i) total integrated absorbance and (ii) normalized absorbance with the initial amount of oxygen (~23.4 cm -1 for sample-a and ~17.4 cm -1 for sample-b) is shown. 15

Total Infrared Absorbance (cm -1 ) 140 (i) 120 100 80 60 40 20 std. ~ 1% GO-ML (Bulk film)-a GO-ML (Thin film)-b Incomplete Oxygen Removal 0 125 250 375 500 625 750 875 Annealing Temperature ( C) Normalized Absorbance 1.4 (ii) 1.2 1.0 0.8 0.6 0.4 GO-ML (Bulk film) GO-ML (Thin film) std. ~ 1% ~46 at. % ~55 at. % 0 125 250 375 500 625 750 875 Annealing Temperature ( C) Figure S8 Integrated infrared absorbance for two different samples of multilayered GO (a) bulk films and (b) thin films. Comparison of (i) total integrated absorbance and (ii) normalized absorbance with the initial amount of oxygen (~103.6 cm -1 for the bulk film and ~48.3 cm -1 for the thin film) is shown. 16

75 C : 60 C 100 C : 75 C CO Absorbance (a. u.) 10-2 CO 2 125 C : 100 C 150 C : 125 C 175 C : 150 C 200 C 350 C 450 C : 350 C 550 C : 450 C 650 C : 550 C 750 C : 650 C 2337cm -1 2000 2100 2200 2300 2400 2500 450 C : 350 C 550 C : 450 C 650 C : 550 C 750 C : 650 C Wavenumber (cm -1 ) 2115 cm -1 Figure S9 Transmission infrared differential spectra of multilayered GO (bulk) at 60-750 C are shown for the release of CO 2 (~2337 cm -1 ) and CO (~2115 cm -1 ). Table S8 Simulated infrared intensities and vibrational frequencies for (A) 1C-vacancy (monovacancy), (B) 2C-vacancy (di-vacancy) defects. 17

C 1s a) 5L GO O 1s b) 5L GO Photoelectron intensity (a.u.) 296 292 288 284 280 536 532 528 C 1s c) 5L GO, annealed O 1s d) 5L GO, annealed 296 292 288 284 280 Binding energy (ev) 536 532 528 Figure S10 Normalized C 1s (a,c) and O 1s (b,d) XPS spectra for a,b) as-synthesized five layered GO on Pt foil, c,d) five layered GO after reduction by vacuum (10-3 -10-4 torr) annealing at 850 C for 5 minutes (~12 hours of total annealing and cooling time) in furnace. Peak fit residuals are shown beneath each spectrum. 18

Table S9 Possible radical production and propagating radicals OH + H 2 = H 2 O + H OH + H 2 O 2 = H 2 O + HO 2 HO 2 + HO 2 = H 2 O 2 + O 2 OH + HO 2 = H 2 O + O 2 OH + ROOH = RO 2 + H 2 O [R1] Ung, A. Y. M. and Back, R. A. The photolysis of water vapor and reactions of hydroxyl radicals. Canadian Journal of Chemistry. 42, 753-763 (1964). Reactions in pure water vapor: OH + OH = H 2 O + O O + OH = O 2 + H OH + OH = H 2 O 2 O + HO 2 = OH + O 2 H + O 2 = HO 2 2HO 2 = H 2 O 2 + O 2 H + HO 2 = H 2 O 2 H + HO 2 = 2OH H + HO 2 = H 2 + O 2 OH + HO 2 = H 2 O + O 2 H + H 2 O 2 = H 2 O + OH H + H 2 O 2 = H 2 + HO 2 OH + H 2 O 2 = H 2 O + HO 2 OH + H 2 = H 2 O + H Reactions with CO and CO 2 radicals: OH + CO = CO 2 + H OH + CO = COOH OH + COOH = H 2 O + CO 2 2COOH = HCOOH + CO 2 OH + CO = CO 2 + H [R2] Frost, G. J., Ellison, G. B. and Vaida, V. Organic Peroxyl Radical Photolysis in the Near- Infrared: Effects on Tropospheric Chemistry. J. Phys. Chem. A 103, 10169-10178 (1999). [R3] Gray, P. Chemistry of free radicals containing oxygen. Trans. Faraday Soc., 55, 408-417 (1959). 19