922 335 9 T2 X 924 919 9 T4 923 T3 919 922 9 T1 925 919 Existing Bridge 6842 919 9 Proposed Bridge 66003
Minnesota Department of Transportation Geotechnical Section Boring Log Descriptive Terminology (English Units) USER NOTES, ABBREVIATIONS AND DEFINITIONS - Additional information available in Geotechnical Manual. This boring was made by ordinary and conventional methods and with care deemed adequate for the Department's design purposes. Since this boring was not taken to gather information relating to the construction of the project, the data noted in the field and recorded may not necessarily be the same as WH... Weight of Hammer WR... Weight of Rod Mud... Fluids in Sample CS... Continuous Sample very loose...0-4 loose...5- medium dense...11-24 dense...25-50 very dense...>50 that which a contractor would desire. While the Consistency - Cohesive s BPF Department believes that the information as to the conditions and materials reported is accurate, it does not warrant that the information is necessarily complete. This information has been edited or abridged and may not reveal all the information which might be useful or of interest to the contractor. Consequently, the Department will make available very soft...0-1 soft...2-4 firm...5-8 stiff...9- very stiff...16- hard...31-60 very hard...> 60 at its offices, the field logs relating to this boring. Since subsurface conditions outside each borehole are unknown, and soil, rock and water conditions cannot be relied upon to be consistent or uniform, no warrant is made that conditions adjacent to this boring will necessarily be the same as or similar to those shown on this log. Furthermore, the Department will not be responsible for any interpretations, assumptions, projections or interpolations made by contractors, or other users of this log. Water levels recorded on this log should be used with discretion since the use of drilling fluids in borings may seriously distort the true field conditions. Also, water levels in cohesive soils often take extended periods of time to reach equilibrium and thus reflect their true field level. Water levels can be expected to vary both seasonally and yearly. The absence of notations on this log regarding water does not necessarily mean that this boring was dry or that the contractor will not encounter subsurface water during the course of construction. WATER MEASUREMENT AB... After Bailing AC... After Completion AF... After Flushing w/c... with Casing w/m... with Mud WSD... While Sampling/ w/aug... with Hollow Stem Auger MISCELLANEOUS NA... Not Applicable w/... with w/o... with out sat... saturated SOIL/CORE TESTS N 60... ASTM D86 Modified Blows per foot with 140 lb. hammer and a standard energy of 2 ft-lbs. This energy represents 60% of the potential energy of the system and is the average energy provided by a Rope & Cathead system.... Moisture Content... Cohesion γ... Sample Density LL... Liquid Limit PI... Plasticity Index Φ... Phi Angle... Percent Core Recovered... Quality Description (Percent of total core interval consisting of unbroken pieces 4 inches or longer) ACL... Average Core Length (Average length of core that is greater than 4 inches long) Core Breaks... Number of natural core breaks per 2-foot interval. DISCONTINUITY SPACING Fractures Distance Bedding Very Close... <2 inches...very Thin Close... 2-12 inches...thin Mod. Close... 12-36 inches...medium Wide... >36 inches...thick WS PD DRILLING SYMBOLS Vane Shear Test Washed Sample (Collected during plug drilling) Augered Plug Drilled Split Tube Sample ( N60 2 in. spilt tube with liners) Thin Wall Sample (3 in. Shelby Tube) % Sand Core Drilled 70 DRILLING OPERATIONS (NV Core Barrel unless otherwise noted) 80 AUG... Augered CS Continuous CD... Core Drilled Sample LS DBD... Disturbed by A/J 0% S Augered & Jetted DBJ... Disturbed by Jetting Jet Jetted PD... Plug Drilled A/P ST... Split Tube ( test) Augered & Plug Drilled TW... Thinwall (Shelby Tube) WS... Wash Sample RELATIVE DENSITY NSR... No Sample Retrieved Compactness - Granular s Index Sheet No. 3.0 March 03 G:\geotech\Public\Forms\INDEX.doc BPF 60 50 COLOR blk... Black wht...white grn... Green brn...brown orng... Orange yel...yellow dk... Dark lt...light IOS... Iron Oxide Stained GRAIN SIZE /PLASTICITY VF... Very Fine pl...plastic F... Fine slpl...slightly Cr... Coarse Plastic SOIL/ROCK TERMS C... Clay Lmst...Limestone L... Loam Sst...Sandstone S... Sand Dolo...Dolostone Si... Silt wx...weathered G... Gravel (No. Sieve to 3 inches) Bldr... Boulder (over 3 inches) T... till (unsorted, nonstratified glacial deposits) Mn/DOT Triangular Textural System 40 SC SCL (plastic) SL (slightly plastic) C CL L 0 % 40 50 60 % Silt 80 70 Si SiCL SiL 70 60 % Clay 50 80 40 Si 0%
Location,, ft. LT Rice Co. Coordinate: X=480754 Y=180654 UNIQUE NUMBER 68280 6612-95 66003 T1 922.0 Latitude (North)=44 24'57.33" Longitude (West)=93 12'25." (ft.) Drill Machine Hammer N60 91286 CME 850 Track CME Automatic Calibrated (psf) (pcf) (ft) Breaks SHEET 1 of 1 Completed /12/06 14 16 org pl to slpl SL w/ seam LS. blk to dk brn w/ brn, moist 7 16 5 5.5 916.5 33 7 S & G w/ a few stone chips, gray-brn, moist to wet 48 13 11.0 911.0 Possible Top of Bedrock SANDY DOLOSTONE, sl wx (possibly weathered in upper 1.0'); thin bedded; mostly pitted and oomoldic except for lower 0.1'; mod hard to hard; pale yel-brn hard drilling 11.3'-13.0' SHAKOPEE FORMATION (Willow River Member).6 6.4 17.1 4.9.1 1.9 22.7 899.3 LITHOGRAPHIC DOLOSTONE, sl wx; V thin to thin bedded; mottled w/ dolomitic sst and thin seams of sst; mod hard; V pale orng SANDY DOLOSTONE, sl wx to gen fresh; V thin to thin bedded; pitted w/ lithogr. clasts & pale yel-brn in upper 0.5'- mod hard to hard; sl lithogr. w/ scattered glauc & pyrite & vertical fractures in lower 2.5'; mod hard to hard; V pale orng to V lt grey DOLOSTONE, sl wx to gen fresh; thin bedded; vuggy and pitted; sl mottled; some clasts in lower 0.5'; sandy along some fracture faces; mod hard to hard; grey Bottom of Hole - 22.7' Water measured at 7.6' while sampling and/or drilling Water measured at 7.7', hole depth.0', /11/06 72 0 22 NA 0.37 NA > 12 Avg. Joint Spacing from 13.0' to.1' = 0. qu = 3400psi (from.3' to.6') Avg. Joint Spacing from.1' to 22.7' = 0.25 Index Sheet Code 3.0 Class:DSB Class: JLR Edit: Date: 3/9/07
UNIQUE NUMBER 68281 6612-95 66003 Location,, ft. LT Rice Co. Coordinate: X=480913 Y=180782 (ft.) Latitude (North)=44 24'58.59" Longitude (West)=93 12'22.96" Drill Machine N 60 (psf) (pcf) T2 91286 CME 850 Track Hammer CME Automatic Calibrated ACL (ft) Core Breaks 922.0 SHEET 1 of 1 Completed /5/06 1.5 9.5 LS w/ a little G, dk brn & moist 81 6 5 42/.5 24/.5 8 S w/ stone chips & pieces, lt brn & moist 50/.2 N/A 50/.4 11.7 9.3 13.0 9.0 14.0 8.0 Possible Top of Bedrock DOLOSTONE, sl wx; V thin to thin bedded; vuggy; becomes sandy in lower 0.2'; mod hard to hard; pale yel-brn WEATHERED SANDY DOLOSTONE; V thin bedded; becomes lithographic in lower 0.2'; mod hard; grey-orng likely a mixture of sandy dolostone, lithographic dolostone and sandstone (recovered material is a mixture of sand and drilling fluid) 50/.2 34 19 0 0 17 - - 14 NA Avg. Joint Spacing from 12.0' to 14.0' = 0. SHAKOPEE FORMATION (Willow River Member) Avg. Joint Spacing not obtained from 14.0' to 19.0' 25 19.0 3.0 19.5 2.5 21.2 0.8 22.7 899.3 27.1 894.9 DOLOSTONE, gen fresh; vuggy; mod hard to hard; pale yel-brn SANDY DOLOSTONE, gen fresh (wx'ed in lower 0.4'); thin bedded; sl vuggy; mod hard to hard; pale yel-brn WEATHERED LITHOGRAPHIC DOLOSTONE; V thin to thin bedded; interspersed sst seams; V pale orn to grey-orng DOLOSTONE, sl wx to gen fresh; mostly thin bedded; scattered sandy dolostone zones, glauconitic zones, pitted/oomoldic/vuggy zones, clasts and pyrite; mod hard to hard; pale yel-brn and lt brn Bottom of Hole - 27.1' Water measured at 6.7' while sampling and/or drilling 91 0 0 33 0.50 > 13 Avg. Joint Spacing from 19.0' to 22.7' = 0. qu = 1600psi (from 24.2'' to 24.5') Avg. Joint Spacing from 22.7' to 27.1' = 0.19 qu = 4600psi (from 26.6' to 26.9') Index Sheet Code 3.0 Class:DSB Class: JLR Edit: Date: 3/9/07
UNIQUE NUMBER 68282 6612-95 Location 66003,, ft. LT Drill Machine Rice Co. Coordinate: X=480855 Y=1807 Latitude (North)=44 24'57.93" Longitude (West)=93 12'23.76" (ft.) 91286 CME 850 Track Hammer CME Automatic Calibrated N60 T3 (psf) (pcf) (ft) Breaks 931.5 SHEET 1 of 2 Completed /24/06 5 Air 17.1 914.4 Water 25 19.4 912.1.7 9.8 22.0 9.5 23.9 7.6 24.8 Index Sheet Code 3.0 Sand and Gravel with stone chips and pieces, light grays and wet Top of Bedrock possibly WEATHERED DOLOSTONE DOLOSTONE, sl wx to gen fresh; V thin to thin bedded; vuggy; mod hard to hard; lt grey SANDY DOLOSTONE, sl wx; thin bedded; scattered clasts; mod hard to hard; grey-orng (Continued Next Page) 16/.5 26/.5 50/.2 8 27 SHAKOPEE FORMATION (Willow River Member) Avg. Joint Spacing from 22.5' to 24.9' = 0. Class:DSB Class: JLR Edit: Date: 3/9/07
UNIQUE NUMBER 68282 Mn/DOT GEOTECHNICAL SECTION - LOG & TEST RESULTS SHEET 2 of 2 6612-95 66003 T3 931.5 6.7 26.7 4.8 LITHOGRAPHIC DOLOSTONE, sl wx; V thin to thin bedded; interspersed sst and sandy dolo seams; mod hard; V pale orng (continued) INTERBEDDED SANDSTONE & SANDY DOLOSTONE, sl wx; V thin to thin bedded; interspersed clasts; mostly mod hard; grey-orng to pale yel-brn N60 (ft) 87 6 (psf) 0.35 (pcf) Breaks Mostly rubble and scattered thin pieces. Avg. Joint Spacing of measureable pieces from 24.9' to 28.2' = 0.14 29.7 1.8 31.7 899.8 33.0 898.5 DOLOSTONE, sl wx to gen fresh; thin bedded; vuggy and pitted; mod hard to hard; lt grey SANDY DOLOSTONE, sl wx; V thin to thin bedded; pitted; interspersed sst seams; becomes lithographic in lower 0.3'; mod hard to hard; pale yel-brn and grey-orng 0 0.38 Avg. Joint Spacing from 28.2' to 33.0' = 0.19 qu = psi (from 32.3' to 32.6') Bottom of Hole - 33.0' Water (river bottom) measured at 17.1' Class:DSB Class: JLR Edit: Date: 3/9/07
UNIQUE NUMBER 68468 6612-95 Location 66003 T4 Rice Co. Coordinate: X=4809 Y=180761 Latitude (North)=44 24'58.39",, ft. LT Longitude (West)=93 12'23.02" (ft.) Drill Machine Hammer CME Automatic Calibrated N60 91286 CME 850 Track (psf) (pcf) (ft) Breaks.0 SHEET 1 of 2 Completed 2/21/07 42 5 3.5.5 Possible Top of Bedrock WEATHERED LITHOGRAPHIC DOLOSTONE; sandy laminations visible; soft; grey-orng 76 Shakopee (Willow River Member) 6.0 9.0 8.0 913.0 DOLOSTONE; pale yel-brn Driller's Note: Very hard rough drilling 6.8'-9.6' SANDY DOLOSTONE, sl wx to wx; oomoldic; mod hard; lt brn 50/.4.1 9.9 11.7 9.3 DOLOMITIC SANDSTONE, sl wx (wx in lower 0.1'); thin 12.6 bedded; strongly cemented; some interbedded crystalline dolo; 8.4 several clasts; mod hard; lt brn 13.3 LITHOGRAPHIC DOLOSTONE, sl wx (wx in upper 0.1'); V thin 7.7 bedded; interspersed sandstone laminations; soft to mod hard; yel-grey to lt grey.9 5.1 19.8 1.2 21.1 899.9 DOLOSTONE, sl wx; V thin to thin bedded; crystalline; vuggy & pitted; mod hard to hard; pale yel-brn DOLOMITIC SANDSTONE, sl wx; V thin to thin bedded; some scattered lithographic dolo, chert and sandstone clasts; recovered sandstone is strongly cemented; mod hard; grey-orng SANDY DOLOSTONE, sl wx; mostly thin bedded in upper 2.0', and V thin to thin in lower 1.9'; sl vuggy and sl pitted/oomoldic; interspersed beds of crystalline dolo, dolomitic sandstone, clasts and lithics; mod hard; V pale to pale yel-brn INTERBEDDED DOLOMITIC SANDSTONE & LITHOGRAPHIC DOLOSTONE, sl wx; V thin bedded; soft to mod hard; V pale orng & lt grey 0 74 94 42 23 18 0.42 0.38 0.45 12 NA 14 > qu = 10psi (from.2' to.5') Avg. Joint Spacing from 9.6' to 12.6' = 0." qu = psi (from 11.7' to 12.0') Scattered small voids from 13.3' to.9' (based on core obserbvations and driller's note) qu = 3550psi (from 16.5' to 16.8') Avg. Joint Spacing from.9' to 17.9' = 0.25" Avg. Joint Spacing from 17.9' to.0' = 0.16" Avg. Joint Spacing from.0' to 21.6' = 0.11" INTERBEDDED DOLOSTONE & SANDY DOLOSTONE, sl wx; mostly thin bedded w/ some V thin zones; interspersed beds of sandstone, lithographic dolostone, glauconite, clasts and lithics; mod hard; V pale to pale yel-brn 12 qu = 000psi (from 22.0' to 22.3') 25 Index Sheet Code 3.0 (Continued Next Page) Class: Class: JLR Edit: Date: 3/9/07
UNIQUE NUMBER 68468 Mn/DOT GEOTECHNICAL SECTION - LOG & TEST RESULTS SHEET 2 of 2 6612-95 66003 T4.0 N 60 94 26 (psf) (pcf) Breaks (ft) 0.43 28.0 893.0 INTERBEDDED DOLOSTONE & SANDY DOLOSTONE, sl wx; mostly thin bedded w/ some V thin zones; interspersed beds of sandstone, lithographic dolostone, glauconite, clasts and lithics; mod hard; V pale to pale yel-brn (continued) 12 rubble Avg. Joint Spacing from 21.6' to 27.9' = 0.26" ONEOTA DOLOSTONE DOLOSTONE, sl wx; thin to med bedded; vuggy and sl mottled with argillaceous dolostone; mod hard; yel-grey 80 50 0.83 6 qu = 3400psi (from.3' to.6') Avg. Joint Spacing from 29.2' to 32.6' = 0.56" 32.6 888.4 Class: Class: JLR Edit: Date: 3/9/07