Trace elemental analysis solutions for your application June 6, 2018
Understanding how each technique works Components of instrument Selection Criteria Application Fields OUTLINE
All these techniques can be used to measure trace metals Flame Atomic Absorption Spectroscopy (FAAS) Graphite Furnace Atomic Absorption Spectroscopy (GFAAS) Inductively Coupled Plasma Emission Spectroscopy (ICP-OES) Inductively Coupled Plasma Mass Spectrometry (ICP-MS) Most labs will have several techniques available. How do you choose the best one to use for a given task?
What is atomic absorption spectrometry? (AAs) The technique uses basically the principle that free atoms generated in an atomizer can absorb radiation at specific frequency AAs quantifies the absorption of ground state atoms in the gaseous state The atoms absorb UV or Vis light and make transitions to higher electronic energy levels The analyte concentration is determined from the amount of absorption
What is atomic absorption spectrometry? (AAs) Flame Atomic Absorption Spectroscopy (FAAS) Graphite Furnace Atomic Absorption Spectroscopy (GFAAS) Air/C 2 H 2 N 2 O/C 2 H 2
Flame Atomic Absorption Spectroscopy (FAAS)
Light source : Hollow cathode lamp (HCL) Ar or Ne Window Remember atoms absorb and emit light at a specific wavelength Ar + M* M* Light is passed through the flame from a Hollow Cathode Lamp l M (HCL) Mspecific 0 0 to the element of Ar analytical + interest (-) (-) (-) Sputtering Excitation Emission M 0 Atoms absorb and emit light at a specific wavelength Light is passed through the flame from a Hollow Cathode Lamp (HCL) specific to the element of analytical interest
What is atomic absorption spectrometry? (AAs)
What is atomic absorption spectrometry? (AAs) Flame Atomic Absorption Spectroscopy (FAAS) Graphite Furnace Atomic Absorption Spectroscopy (GFAAS) Graphite tube
Graphite Furnace Atomic Absorption Spectroscopy (GFAAS) This technique is essentially the same as flame AA, except the flame is replaced by a small, electrically heated graphite tube, or cuvette, which is heated to a temperature up to 3000 C to generate the cloud of atoms. The higher atom density and longer residence time in the tube improve furnace AAS detection limits by a factor of up to 1000x compared to flame AAS, down to the sub-ppb range. However, because of the temperature limitation and the use of graphite cuvettes, refractory element performance is still somewhat limited.
Graphite Furnace Atomic Absorption Spectroscopy (GFAAS) Superior sensitivity detect anaytes at concentrations 10-100 times lower than flame High conversion efficiency of sample into free atoms. Low sample volumes 20 µl. Directs analysis of some types of liquid sample Low spectral interference due to generally higher temperatures. Is fully automated and can be left to run overnight Atomizer Lead (Pb) Copper (Cu) Arsenic (As) Flame 0.10 mg/l 0.04 mg/l 0.40 mg/l Furnace 0.07 μg/l 0.09 μg/l 0.26 μg/l
What is Inductively Coupled Plasma (ICP-OES)? A plasma will excite the atoms and ions that travel through it. When an atom or ion is excited, its electrons jump from a lower to higher energy level. Upon relaxation of these electrons to their initial 'ground' state, energy is emitted in the form of photons. The emitted photons possess wavelengths that are characteristic of their respective elements A detector measures the intensity of the emitted light, and calculates the concentration of that particular element in the sample Temperatures as high as 10,000 C, where even the most refractory elements are atomized with high efficiency. As a result, detection limits for these elements can be orders of magnitude lower with ICP than with FAAS techniques, typically at the 1-10 parts-per-billion level. OES
What is Inductively Coupled Plasma (ICP-OES)?
How to create the plasma? RF power is applied to the load coil, an alternating current moves back and forth within the coil, or oscillates. This RF oscillation of the current in the coil causes RF electric and magnetic fields to be set up. With argon gas being swirled through the torch, a spark is applied to the gas causing some electrons to be stripped from their argon atoms. These electrons are then caught up in the magnetic field and accelerated by them. Adding energy to the electrons by the use of a coil in this manner is known as inductive coupling
How to create the plasma? The ICP discharge appears as a very intense, brilliant white, teardrop-shaped discharge. Which can be listed as several zone: Induction region (IR) Preheating zone (PHZ) - desolvation, vaporization, atomization Initial radiation zone (IRZ) - excitation and/or ionization Normal analytical zone (NAZ) - measurement of the emission Tail Plume - oxide formation, self absorption, molecular emission/absorption IR Tail plume PHZ NAZ IRZ
Process occurring during Atomization and Ionization ICP-MS ICP-OES Spray Nebulization
Temperature ICPOES / ICPMS GAAS Flame AAS
Components of ICP-OES Consist of : Nebulizer Spray chamber Torch plasma and Viewing positions Monochromator Detector
Sample Introduction Nebulizer Spray chamber Torch
Sample Introduction - Nebulizer Nebulizer Spray chamber Torch Nebulizer are devices that convert a liquid into an aerosol that can be transported to the plasma. made from glass or plastics such as PFA Flow rate of between 0.01 and 3 ml/min Concentric nebulizer for use with samples containing up to 3% TDS The glass construction should not be used with hydrofluoric acid or caustics such as the alkali hydroxides. Quartz construction is more resistant to chemical attack.
Sample Introduction Spray chamber Nebulizer Spray chamber Torch Cyclonic Scott type The purpose of the spray chamber is to remove droplets produced by the nebulizer that are >8 µm in diameter. Glass cyclonic spray chamber Important considerations here include the wash-in time, wash-out time, stability, and sensitivity Drainage process might be smooth and continuous. Analyst might observe faster wash-in and wash-out times with glass construction than with polymer due in part to better wettability of the glass (lack of beading).
Sample Introduction - Torch Nebulizer Spray chamber Torch
Sample Introduction - Torch made from Quartz Auto alignment of the torch in the torch box Ease of use for routine maintenance Auxiliary gas Coolant gas Nebulizer gas + + = Argon gas
Sample Introduction
Sample Introduction
Viewing positions Radial Dual view (Duo) Axial Selectable viewing zone, Avoid matrix effects More suitable for hard matrices Alkali metal calibration is more linear No self absorption Lower sensitivity Longer path length, Higher analyte emission Improve sensitivity apox. 5 10 times Better detection limits Problems : Increase in spectral and matrix induced interference (Self-absorption effect, Reduced linear dynamic range)
Interference : Axial viewing Shear gas : require additional high flow rate shear gas to remove interferences Cone interface Ar or N 2 1 L/min Air or N 2 18-25 L/min http://www.homedepot.com/ Ceramic cone icap7000 plus Thermo Scientific
Monochromator and Detector Simultaneous analysis was carried out by using Echelle grating optics and coupled to solid state detector also know Charge transfer device Charge Injection Devices
Inductively Coupled Plasma Mass spectrometry (ICP-MS) Inductively coupled plasma mass spectrometry (ICP-MS) is a type of mass spectrometry which is capable of detecting metals and several non-metals at concentrations as low as one part in 10 12 (ppt). This is achieved by ionizing the sample with inductively coupled plasma (isotope ions) and then using a mass spectrometer to separate and quantify those ions. M +
Process occurring during Atomization and Ionization ICP-MS Spray Nebulization
Inductively Coupled Plasma Mass Spectrometry (ICP-MS) m/z
How to extract the ions into MS? low pressure region of the mass spectrometer (<1x10-5 torr) The positively charged ions that are produced in the plasma are extracted into the vacuum system, via a pair of interface cones and the extraction lens Extraction lens Skimmer cone Sample cone Interface Intermediate vacuum region created by the two interface cones. atmospheric pressure (1-2 torr) Vacuum region Interface region
https://www.youtube.com/watch?v=mpdxfpwkcea
https://www.youtube.com/watch?v=4xm_hnrozou
https://www.youtube.com/watch?v=r_6szcb8f9a
How to maintain low background and drift? Mass Analyzer The Right Angular Positive Ion Deflection (RAPID) lens unique 90 cylindrical ion lens providing high ion transmission across the entire mass range. Collision/Reaction cell and Mass Filter (Quadrupole) Ion Ion, Neutral, Photons Neutral, Photons Elimination of neutral species
Polyatomic interference 40 Ar 16 O 40 Ca 16 O 40 Ar 35 Cl
How to remove Polyatomic Interference? Mass Analyzer Collision/Reaction cell Qcell Collision/Reaction Cell (CRC) Flatapole technology for improved transmission Low mass cut off filters out unwanted precursor ions Single mode interference removal with He He KED filters out unwanted polyatomic interferences Small CRC volume for fast gas exchange, <10s Flexibility to work with reactive gases, such as mixtures of O 2 7% dilute H 2 or 1% NH 3 Non-consumable, zero-maintenance
How to remove Polyatomic Interference? He KED mode Decreasing Energy Collisional retardation / energy filtering Quadrupole Cell Pre-Cell He He He He He From plasma To detector He He He He He Collision/Reaction gas atom or molecule Energy Barrier Simple, effective interference removal Analyte Ion M + - Small collision crosssection Polyatomic Species e.g. ArX + Larger collision cross-section
ICPMS
Selection Criteria Typical selection criteria includes: Which / How many elements? Detection Limits? Sample Consumption? Concentration range? Analytical Speed and Productivity? Sample Matrix? Operator skill?
A cross-technique comparison Easy to use Flame AA GFAAS ICP-OES ICP-MS Very good detection limits Easy to use Excellent detection limits Very fast Small sample size Multi-element Multi-element Lowest capital cost Moderate price High productivity High productivity Very compact instrument Very compact instrument Very economical for many samples and/or elements Very economical for many samples and/or elements Good performance Robust interface Wide dynamic range Robust interface Excellent screening abilities Fast semi-quantitative screening Very compact instrument High total dissolved solids Hybrid techniques LA- ICP-MS (solids)*, IC or LC- ICP-MS (speciation)* Excellent detection limits
Sample Requirements Criteria
Precision Precision is a measure of the confidence you can have in your measured results Flame AAS Short term : 0.1-1.0% Long term : 1-2% (2beam optic) Short term 0.5-5% Long term : highly dependent on the tube type and condition GFAAS ICP-OES Short term : 0.1-2% Short term : 0.5-2% Long term : <1-5% Long term : <4% ICP-MS Long-term precision in any of the techniques can be improved by more frequent instrument calibration or drift correction techniques. The use of internal standardization can significantly improve precision in ICP and ICPMS
Speed of Measurement How many samples can a particular technique analyze in a given time? How many elements can be determined? Sequential ICP-AES (Sequential): 5-6 elements per minute for each sample FAAS: 4 seconds per element for each sample GFAAS: 2-3 minutes per element for each sample Simultaneous ICP-MS: All elements in 2-3 minutes ICP-AES (Simultaneous): All elements in 2-3 minutes Analytical Speed and Productivity? Which / How many elements? For less than 5 elements per sample, FAAS is often the quickest technique, depending on the total number of samples. For 5-15 elements, sequential ICP- AES is the optimum choice. Above 15 elements, either ICP-MS or simultaneous ICP-OES is the best choice. GFAAS will always be the slowest of the techniques
Operating cost Performance FAAS acetylene/nitrous oxide gases compressed air source hollow cathode lamps reagents and standards power ICP-OES argon gas quartz torches reagents and standards pump tubing power cooling water GFAAS argon gas hollow cathode lamps graphite tubes reagents and standards power cooling water ICP-MS argon gas quartz torches sampling and skimmer cones reagents and standards pump tubing power cooling water ice 3000 Series AA icap 7000 plus Series ICP Investment ELEMENT 2 ICP- MS icap Qnova ICP-MS
Summary Overall Technique Selection Summary For ultimate throughput, choose ICP-OES and ICP-MS If ultimate DLs, choose ICP-MS For strictly regulated industries/applications such as USEPA, please check that data is accepted
Application Fields
Which Instrument would you recommend for analysis of Cadmium in Chocolate? Cadmium is a heavy metal used in a variety of applications, such as steel plating, as a pigment in plastics and glasses, and in the production of batteries. These industrial activities are the main route through which cadmium is released into the environment where it accumulates in water and soil, and subsequently plants, animals and fish through uptake and ingestion. One of the main routes of human exposure to cadmium is therefore through the ingestion of foodstuffs. Typical maximum levels of cadmium in foodstuffs are currently between 0.05 0.2 mg/kg wet weight. The main ingredients in chocolate consist of cocoa, milk and fats, each of which is a potential source of cadmium. Sample Preparation 0.3 g + 7 ml HNO 3 + 1 ml H 2 O 2 Left to stand for 5 mins diluted to 100 ml with DI water 1 mg/l cadmium sub-standard was prepared in deionised water for spiking of samples prior to digestion
Analysis of Cadmium in Chocolate by GFAAS 10 μg/l sub-standard was made up in 7% nitric acid and 1% hydrogen peroxide to matrix match to the digested samples. Blank and diluent were also prepared at 7% nitric acid and 1% hydrogen peroxide. A matrix modifier : 2 g/l of ammonium nitrate Cadmium was analyzed at 228.8 nm and Zeeman background correction Furnace Method Results for the analysis of cadmium in chocolate following analysis by GFAAS Thermo Scientific ice3500 AAS
Analysis of toxic elements in drinking and bottled waters China and India have seen a huge increase in the consumption of bottled water in the last decades Chinese regulations: GB 8537 2008 - Drinking natural mineral water GB 17324 2003 - Hygienic standard of bottled purified water for drinking GB 5749 2006 - Standards for drinking water quality GB 3838 2002 - Environmental quality standard for surface water Indian regulations: IS 10500:2012 - Drinking Water IS 13428:2005 - Packaged natural mineral water IS 14543:2004 - Packaged drinking water (other than packaged natural mineral
มาตรฐานค ณภาพน าเพ อบร โภค http://www.pcd.go.th/info_serv/reg_std_water01.html#s2
Analysis of toxic elements in drinking and bottled waters by ICP-OES Thermo Scientific icap 7200 ICP-OES Duo with Qtegra Intelligent Scientific Data Solution (ISDS) Software Tap water sample from Dingpu river area, Shanghai Tap water sample from Jinqiao lake area, Shanghai Waterman (packaged drinking water) Nestle (natural mineral water) Evian (natural mineral water) Samples did not require any pre-treatment Samples were analyzed directly after preservation in 0.5% AR grade nitric acid (HNO 3 )
Analysis of toxic elements in drinking and bottled waters by ICP-OES Averaged results and method detection limits in μg kg-1. All QC recoveries were within 10% Stability of the 10 μg kg-1 QC check over 4 hours
Which technique? Which technique would you use for the analysis of Lead in blood?? They do not have detection limits but would like to detect as low as possible
A fully quantitative research method for the analysis of Lead in whole blood Dust, Paint, Soil, Industrial, Water, Toy, Food The United States Centers for Disease Control and Prevention (CDC) states that Blood Lead Levels (BLL) >70 μg/dl (700 ng/ml) can cause serious health effects. BLL as low as 10 μg/dl (100 ng/ml) are associated with cognitive development, growth, and behavioral issues in children between the ages of 1-5 years. As, Cd, Cr, Pb, Hg and Se in whole blood and Certified reference materials (Seronorm Trace Elements Whole Blood)
A fully quantitative research method for the analysis of Lead in whole blood using ICP-MS Add Ultrapure water - Add 100 ml of blank or standard or sample or QC - Add 4900 ml of Diluent* Vortex mixing for 15 minutes before use Sample is 50 fold diluted with diluent Plastic tube Vortex mixer Analysis by ICP-MS * Tetramethylammonium hydroxide (TMAH, 1.5%), Hydrochloric acid (HCl, 1.5%), Ammonium Pyrrolidine dithiocarbamate (APDC), Triton-X and 0.1 µg/l of 103 Rh (Internal standard)
A fully quantitative research method for the analysis of Lead in whole blood using ICP-MS 82 Se is chosen based on less possible argon based interferences compare to 80 Se ( 40 Ar 2+ ). Selected analyte isotopes 75 As 114 Cd 82 Se Internal standard isotope 103 Rh 52 Cr 202 Hg 63 Cu 208 Pb 114 Cd is chosen based on it abundance.
How to remove Polyatomic Interference? Collision Cell Technology (CCT) 75 As + Comprehensive Interference Removal Quadrupole isolates ions wanted for measurement He KED mode ArCl + Ca(OH) 2 H + He KED filters out unwanted polyatomic interferences, based on difference in crosssectional size of the analyte and polyatomic Unique Flatapole Design 75 As+ 40Ar35Cl + Ca(OH) 2 H +
A fully quantitative research method for the analysis of Lead in whole blood using ICPMS MDL include 50 times dilution
A fully quantitative research method for the analysis of Lead in whole blood using ICPMS Element CRM Certified Value (ng/ml) Acceptable range (ng/ml) Found (± SD, n = 3) (ng/ml) As L1 2.4 1.4-3.4 2.77±0.09 L2 14.3 8.5-20-1 15.24±0.78 L3 30.4 23.1-37.7 30.14±1.41 Cd L1 0.36 0.32 0.40 0.36 ± 0.11 L2 5.8 5.40 6.20 6.12 ± 0.18 L3 12.1 10.8 13.4 12.6 ± 0.39 Cr L1 0.86 0.48 1.24 1.22 ± 0.04 L2 11.8 7 16.6 12.8 ± 0.34 L3 23.2 18.5 27.9 24.27 ± 0.64 Element CRM Certified Value (ng/ml) Acceptable range (ng/ml) Found (± SD, n = 3) (ng/ml) Hg L1 1.5 0.90 2.10 2.24 ± 0.24 L2 16 9.60 22.40 20.47 ± 0.39 L3 37.1 29.6 44.6 40.41 ± 1.55 Pb L1 10.2 6.00 14.40 10.68 ± 0.36 L2 310 186-434 394 ± 13 L3 447 401-493 536 ± 22 Se L1 59 35 69 69.03 ± 0.59 L2 112 66 158 131 ± 5 L3 272 217 327 258 ± 8
Thank you for your attention!!! www.scispec.co.th Follow Us