730A High Performance Multifunction Calibrator Extended specifications
General Specifications Warm-Up Time... Twice the time since last warmed up, to a maximum of 30 minutes. System Installation... Rack mount kits available. Standard Interfaces... IEEE-4, RS-3, USB.0 device, Ethernet, 7A, 10A, phase lock in (BNC), phase reference out (BNC). Temperature Performance Operating... 0 C to 0 C Calibration... 1 C to 3 C Storage... -40 C to 7 C Relative Humidity Operating... <0 % to 30 C, <70 % to 40 C, <40 % to 0 C Storage... <9 %, non-condensing. A power stabilization period of four days may be required after extended storage at high temperature and humidity. Safety... IEC 6-1: Overvoltage Category II, Pollution Degree Operating Altitude... 000 m maximum Guard Isolation... 0 V Electromagnetic Environment... IEC 6136-1: Controlled Line Power Line Voltage 730A... 0 V-10 V, 0 V- 40 V % 7A... 0 V, 1 V, 11 V, 10 V, 00 V, 0 V, 30 V, 40 V, % Line... 47 Hz-63 Hz Maximum Power 730A... 300 VA 7A... 70 VA Weight 730A... 7 kg (6 lb) 7A... 3 kg (70 lb) Size 730A Height... 17. cm (7 in), standard rack increment, plus 1. cm (0.6 in) for feet Width... 43. cm (17 in), standard rack width Depth... 64. cm (. in), overall; 9.4 cm (3.4 in), rack depth 7A Height... 13.3 cm (. in) Width and Depth... Both units project.1 cm ( in) from rack front. Fluke Calibration 730A High Performance Multifunction Calibrator
43. cm (17 in) 17. cm (7 in) 64. cm (. in) 6.3 cm (. in) For cable access Figure 1-1. Product Dimensions hhp00.eps Artifact Calibration Standards Requirements The following external standards are necessary to calibrate the 730A to the listed specification. Each external standard used must have an accuracy equal to or less than the listed uncertainty limit. Fluke Standard Traceable Uncertainty 730A Specifications Susceptible to Quantity Nominal Value Limit Uncertainty Limit 73B Voltage V 1. ppm dc volts, ac volts, dc current, ac current 74A-1 Resistance 1 ppm 1, 1.9 74A-k Resistance k ppm ac current, dc current to 0 M 3 Fluke Calibration 730A High Performance Multifunction Calibrator
Electrical Specifications Note Fluke guarantees performance verification using specifications stated to 99 % confidence level. DC Voltage Specifications 730A DC Voltage Specifications Absolute Accuracy Relative Accuracy 1 C C from calibration temperature Range Resolution 4 Hours 90 Days 10 Days 1 Year 4 Hours 90 Days (ppm output + V) 99 % Confidence Level 0 mv nv + 0. 7 + 0. + 0. 9 + 0. + 0.4. + 0.4. V 0 nv 3. + 0. 4 + 0. 4. + 0. 6 + 0. + 0.. + 0. 11 V 1 V. + 3 3 + 3 3. + 3 4 + 3 1 + 3 1. + 3 V 1 V. + 3 + 3. + 4 + 1 + 1. + 0 V V 3. + 0 4 + 0 + 0 6 + 0 + 0. + 0 10 V 0 V + 00 6 + 00 7 + 00 + 00. + 400 3 + 400 9 % Confidence Level 0 mv nv 4 + 0.4 6 + 0.4 6. + 0.4 7. + 0.4 1.6 + 0.4 + 0.4. V 0 nv 3 + 0.7 3. + 0.7 4 + 0.7 + 0.7 1.6 + 0.7 + 0.7 11 V 1 V +.. +. 3 +. 3. +. 0. +. 1. +. V 1 V + 4. + 4 3 + 4 3. + 4 0. + 4 1. + 4 0 V V 3 + 40 3. + 40 4 + 40 + 40 1.6 + 40 + 40 10 V 0 V 4 + 400 4. + 400 6 + 400 6. + 400 + 400.4 + 400 DC Zeros calibration required every 30 days. DC Voltage Secondary Performance Specifications and Operating Characteristics Temperature Coefficient Adder [] Noise Stability [1] 1 C 0 - C and Range 4 Hours 40-0 C Linearity 1 C 0 mv. V 11 V V 0 V 10 V - 40 C Bandwidth 0.1 - Hz pk-pk Bandwidth - khz RMS (ppm output + V) (ppm output + V) / C (ppm output + V) V 0.3 + 0.3 0.4 + 0.1 1. + 0. 1 + 0. 0.1 + 0.1 0.3 + 1 0.3 + 0.1 1. + 1 + 0.6 0.1 + 0.4 1 0.3 +. 0.1 + 0. 1 + 1. 0.3 + 0.1 + 0 0.4 + 0. + 0.4 1. + 3 0.3 + 4 0.1 + 4 0 0. + 40 0.3 + 1. + 40 1 + 40 0.1 + 60 10 0. + 00 0. + 3 + 00 1 + 00 0.1 + 300 00 1. Stability specifications are included in the absolute accuracy values in the primary specification tables.. Temperature coefficient is an adder to absolute accuracy specifications that does not apply unless operating more than C from calibration temperature. Minimum Output... 0 V for all ranges, except 0 V for 10 V range Maximum Load... 0 ma for. V through 0 V ranges; 0 ma for 10 V range; 0 output impedance on 0 mv range; all ranges <00 pf, > Load Regulation... <(0. ppm of output + 0.1 ppm of range), full load to no load Line Regulation... <0.1 ppm change, % of selected nominal line Settling Time... 3 seconds to full accuracy; + 1 second for range or polarity change; + 1 second for 10 V range Overshoot... < % Common Mode Rejection... 140 db, DC to 400 Hz Remote Sensing... Available 0 V to 10 V, on. V through 10 V ranges Fluke 730A Extended Specifications 4 Fluke Calibration 730A High Performance Multifunction Calibrator
AC Voltage Specifications Range. mv 1 nv Resolution mv nv 0 mv 0 nv. V 1 V V V 0 V [] 0 V 10 V [1] 1 mv 7A Amplifier: 10 V 70 V 1 mv 730A AC Voltage Specifications: 99 % Confidence Level Absolute Accuracy C from calibration temperature Relative Accuracy 1 C 4 Hours 90 Days 10 Days 1 Year 4 Hours 90 Days (Hz) (ppm output + V) 0 + 70 + 90 + 300 + 0 + 70 + 0 + + 1 + 11 + 0 + + + 90 + 9 + 0 + 60 + 6 + 0 + 30 + 40 + 0 + + 9 + 00 + 6 40 + 6 70 + 6 600 + 6 00 + 6 0 + 6 0 k - 300 k 00 + 1 100 + 1 10 + 1 1300 + 1 30 + 1 400 + 1 1400 + 100 + 1600 + 1700 + 00 + 00 + 00 k - 1 M 900 + 30 + 30 + 3400 + 700 + 3000 + 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 1-0 0-1 k 1 k - 0 k 0 k - 30 k 30 k - 0 k 1. Maximum output 0 V from 1-0 Hz.. See Volt-Hertz capability in Figure A. 0 + 0 + + 0 + 00 + 6 00 + 1 1400 + 900 + 0 + 1 0 + 6 + 13 + 370 + 0 60 + 1400 + 30 700 + 60 0 + 0 9 + 0 4 + 7 + 1 9 + 40 30 + 0 00 + 0 1600 + 400 0 + 00 9 + 00 4 + 70 7 + 10 9 + 0 + 00 00 + 00 100 + 4000 0 + 9 + 7 + 0.7 90 + 1. 160 + 3 900 + 0 000 + 0 000 + 0 300 + 0 70 + 4 7 + 4 + 6 30 + 11 30 + 11 600 + 4 70 + + 90 + 30 + 40 + 6 100 + 1 100 + 30 + 70 + 1 + 66 + 140 + 30 + 0 700 + 100 + 30 900 + 60 70 + 0 0 + 0 46 + 77 + 1 97 + 40 370 + 0 10 + 0 100 + 400 70 + 00 0 + 00 46 + 70 77 + 10 97 + 0 90 + 00 10 + 00 1600 + 4000 70 + 0 + 60 + 0.7 9 + 1. 170 + 3 00 + 0 00 + 0 9000 + 0 30 + 0 7 + 4 0 + 4 1 + 6 360 + 11 360 + 11 1300 + 4 90 + 1 + 9 + 40 + 70 + 6 10 + 1 1600 + 30 + 90 + 1 1 + 67 + 14 + 390 + 0 70 + 1600 + 30 30 + 60 90 + 0 + 0 47 + 7 + 1 9 + 40 30 + 0 110 + 0 1900 + 400 90 + 00 + 00 47 + 70 7 + 10 9 + 0 9 + 00 110 + 00 1700 + 4000 300 + 11 + 0 + 0 + 600 + 6 1300 + 1 1700 + 3400 + 300 + 1 11 + 70 + 10 + 400 + 0 00 + 1700 + 30 3300 + 60 300 + 0 1 + 0 4 + 0 + 1 0 + 40 400 + 0 100 + 0 000 + 400 300 + 00 1 + 00 4 + 70 0 + 10 0 + 0 300 + 00 100 + 00 100 + 4000 (ppm output + mv) 90 + + 6 + 0.7 97 + 1. 17 + 3 0 + 0 300 + 0 900 + 0 340 + 0 0 + 4 + 4 13 + 6 440 + 11 440 + 11 1600 + 4 300 + 1 + 6 + 0.7 0 + 1. 10 + 3 10 + 0 400 + 0,000 + 0 360 + 0 + 4 90 + 4 16 + 6 600 + 11 600 + 11 300 + 4 0 + 0 + 60 + + 00 + 6 30 + 1 00 + 700 + 0 + 1 0 + 60 + + 00 + 0 30 + 00 + 30 600 + 60 0 + 0 9 + 0 30 + 70 + 1 0 + 40 70 + 0 900 + 0 100 + 400 0 + 00 9 + 00 30 + 70 70 + 10 0 + 0 70 + 00 900 + 00 1300 + 4000 0 + 9 + 4 + 0.7 7 + 1. 140 + 3 600 + 0 400 + 0 000 + 0 300 + 0 0 + 4 0 + 4 + 6 160 + 11 160 + 11 30 + 4 70 + + 6 + 9 + 0 + 6 400 + 1 00 + 3000 + 70 + 1 + 6 + 9 + 0 + 0 400 + 00 + 30 00 + 60 70 + 0 0 + 0 40 + 7 + 1 + 40 90 + 0 00 + 0 1300 + 400 70 + 00 0 + 00 40 + 70 7 + 10 + 0 90 + 00 00 + 00 1400 + 4000 70 + 0 + 0 + 0.7 0 + 1. 10 + 3 700 + 0 4700 + 0 00 + 0 30 + 0 + 4 + 4 + 6 30 + 11 30 + 11 100 + 4 Fluke Calibration 730A High Performance Multifunction Calibrator
Range Resolution. mv 1 nv mv nv 0 mv 0 nv. V 1 V V V 730A AC Voltage Specifications: 9 % Confidence Level Absolute Accuracy C from calibration temperature Relative Accuracy 1 C (Hz) 4 Hours 90 Days 10 Days 1 Year 4 Hours 90 Days (ppm output + V) 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 40-0k 0k - 0k 0k - 0k 0k - 300k 300k - 00k 00k - 1M 00 + 4 0 + 4 70 + 4 170 + 4 400 + 00 + 10 + 0 400 + 0 00 + 4 0 + 4 70 + 4 170 + 4 400 + 00 + 10 + 0 400 + 0 00 + 1 0 + 7 4 + 7 + 7 96 + 17 3 + 0 10 + 400 + 4 00 + 40 7 + 1 37 + 61 + 79 + 30 76 + 0 00 + 00 1300 + 300 00 + 400 7 + 10 37 + 0 61 + 0 7 + 00 3 + 600 00 + 000 100 + 300 0 + 4 + 4 7 + 4 10 + 4 460 + 900 + 100 + 0 00 + 0 0 + 4 + 4 7 + 4 10 + 4 460 + 900 + 100 + 0 00 + 0 0 + 1 + 7 + 7 1 + 7 9 + 17 3 + 0 100 + 00 + 4 0 + 40 0 + 1 39 + 63 + 1 + 30 300 + 0 900 + 00 100 + 300 0 + 400 0 + 10 39 + 0 63 + 0 0 + 00 43 + 600 900 + 000 1300 + 300 30 + 4 7 + 4 77 + 4 190 + 4 40 + 00 + 1300 + 0 600 + 0 30 + 4 7 + 4 77 + 4 190 + 4 40 + 00 + 1300 + 0 600 + 0 30 + 1 7 + 7 6 + 7 11 + 7 303 + 17 600 + 0 1300 + 600 + 4 30 + 40 + 1 40 + 6 + + 30 314 + 0 90 + 00 1600 + 300 30 + 400 + 10 40 + 0 6 + 0 1 + 00 49 + 600 900 + 000 1400 + 300 40 + 4 90 + 4 0 + 4 00 + 4 00 + 0 + 1400 + 0 700 + 0 40 + 4 90 + 4 0 + 4 00 + 4 00 + 0 + 1400 + 0 700 + 0 40 + 1 90 + 7 7 + 7 10 + 7 3 + 17 6 + 0 1400 + 700 + 4 40 + 40 90 + 1 4 + 67 + + 30 336 + 0 00 + 00 1700 + 300 40 + 400 90 + 10 4 + 0 67 + 0 3 + 00 4 + 600 00 + 000 100 + 300 00 + 4 0 + 4 0 + 4 70 + 4 160 + 0 + 60 + 0 0 + 0 00 + 4 0 + 4 0 + 4 70 + 4 160 + 0 + 60 + 0 0 + 0 00 + 1 0 + 7 0 + 7 70 + 7 160 + 17 0 + 0 60 + 0 + 4 00 + 40 7 + 1 + + 0 + 30 30 + 0 700 + 00 00 + 300 00 + 400 7 + 10 + 0 + 0 0 + 00 0 + 600 700 + 000 10 + 300 0 + 4 + 4 + 4 0 + 4 10 + 30 + 00 + 0 400 + 0 0 + 4 + 4 + 4 0 + 4 10 + 30 + 00 + 0 400 + 0 0 + 1 + 7 + 7 0 + 7 10 + 17 30 + 0 00 + 400 + 4 0 + 40 0 + 1 3 + 60 + + 30 0 + 0 00 + 00 10 + 300 0 + 400 0 + 10 3 + 0 60 + 0 + 00 70 + 600 00 + 000 100 + 300 0 V [] 0 V 0 k - 300 k 00 k - 1 M 10 V [1] 1 mv 1-0 0-1 k 7A Amplifier: 10 V 1 k - 0 k 1 mv 0 k - 30 k 70 V 30 k - 0 k 1. Maximum output 0 V from 1-0 Hz.. See Volt-Hertz capability in Figure A. 00 +4 7 + 1. 4 + 0.6 70 + 1 10 +. 700 + 16 4000 + 40 6000 + 0 40 + 16 + 3. 7 + 4 + 6 30 + 11 30 + 11 600 + 4 0 + 4 0 + 1. 47 + 0.6 7 + 1 130 +. 00 + 16 400 + 40 7000 + 0 60 + 16 60 + 3. 0 + 4 1 + 6 360 + 11 360 + 11 1300 + 4 (ppm output + mv) 30 + 4 + 1. 0 + 0.6 77 + 1 140 +. 0 + 16 4300 + 40 700 + 0 0 + 16 6 + 3. + 4 13 + 6 440 + 11 440 + 11 1600 + 4 40 + 4 90 + 1. + 0.6 0 + 1 10 +. 900 + 16 4400 + 40 000 + 0 300 + 16 70 + 3. 90 + 4 16 + 6 600 + 11 600 + 11 300 + 4 00 + 4 7 + 1. 3 + 0.6 60 + 1 1 +. 00 + 16 3600 + 40 600 + 0 40 + 16 40 + 3. 0 + 4 + 6 160 + 11 160 + 11 30 + 4 0 + 4 0 + 1. 40 + 0.6 6 + 1 10 +. 600 + 16 300 + 40 7000 + 0 60 + 16 4 + 3. + 4 + 6 30 + 11 30 + 11 100 + 4 6 Fluke Calibration 0A Multi-Product Calibrator Extended Specifications
Range. mv mv 0 mv. V V 0 V 10 V AC Voltage Secondary Performance Specifications and Operating Characteristics Temperature Coefficient Stability 1 C [1] 4 Hours - 40 C (Hz) 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 0 k - 300 k 00 k - 1 M 1-0 0-1 k Maximum Distortion Bandwidth Hz- MHz 0 - C Output Impedance and 40-0 C ( ) V V / C (% output + V) 3 3 3 1 (ppm output + V) 10 + 0 0 + 1 1 + + + 0 + 4 0 + 00 + 0 0.0 0.0 0.0 0.1 0. 0.3 0.4 0. 0. 0. 0. 0.4 0. 0.6 1 1 0.0 0.0 0.0 0.1 0. 0.3 0.4 0. 0.3 0.3 0.3 0. 0. 0.6 1 1 (ppm output V) / C + 1 + 1 + 1 + 1 + 1 + 1 1 + 1 + 1 + 4 1 + 4 0 + 0 + 0 + 0 + 0 + 0 + 0 0 0 0.0 + 0.03 + 0.03 + 0.03 + 0.03 + 30 0.3 + 30 0.3 + 30 + 0 0.0 + 11 0.03 + 11 0.03 + 11 0.03 + 11 0.03 + 30 0.3 + 30 0.3 + 30 + 30 0.0 + 16 0.03 + 16 0.03 + 16 0.03 + 16 0.03 + 30 0.3 + 30 0.3 + 30 1 + 30 Load Regulation (ppm output + V) 10 + 0 0 + 0 + + 0.0 + 0 0 + 1 1 + 1 + + 0.03 + 0 1 + 4 + 1 + + 4 0.03 + 0 1 + + 1 + 4 30 + 0.03 + 0 1 + + 4 0 + 4 10 + 16 0.03 + 1 30 + 0 + 1 0 + 1 300 ppm 0.3 + 1 70 + 0 0 + 40 0 + 40 600 ppm 0. + 1 10 + 0 0 + 0 0 + 0 100 ppm 1 + 1 10 + 0 0 + 0 0 + 0 + 0 0.0 + 700 0 + 1 1 + 30 1 + 40 + 0 0.03 + 700 1 + + 4 + 1 + 30 0.03 + 700 1 + + 0 0 + 0 30 + 0 0.03 + 700 1 + + 40 0 + 40 0 + 0 0.0 + 00 30 + 1 0 + 10 0 + 10 0 + 700 0.3 + 00 70 + 0 0 + 300 0 + 300 00 + 10 0.3 + 00 10 + 0 0 + 00 0 + 00 600 + 3000 + 00 10 + 00 0 + 00 0 + 00 + 00 0.0 +,000 0 + 10 1 + 300 1 + 300 + 00 0.0 +,000 1 + 0 + 0 4 + 0 + 300 0.0 +,000 1 + 0 + 0 0 + 0 30 +.600 0.0 +,000 1 + 0 + 00 0 + 00 0 + 3,000 0. + 0,000 30 + 400 0 + 600 0 + 600 0 +,000 1. + 0,000 0 +,000 0 + 00 0 + 00 00 + 0,000 1. + 0,000 00 + 0,000 0 + 00 0 + 00 00 + 1,000 3. + 0,000 (ppm output + mv) (ppm output) / C (ppm output + mv) (% output) 10 + 0. 0 0 + 0.1 0 + 0. + 1 0.07 7 Fluke Calibration 730A High Performance Multifunction Calibrator
7A Amplifier: Range (Hz) 10 V 1 k - 0 k Stability 1 C [1] 4 Hours (ppm output + mv) +. 1 + 40 + 130 + Temperature Coefficient Adder Distortion Bandwidth 0 - C - 40 C and 40-0 C Load Regulation [] Hz - MHz (% output) (ppm output) / C (ppm output + mv) 10 pf 00 pf 30 30 + 1 90 + 6 7 + 11 00 + 30 0. 0. 0.30 0.40 0. 0.1 0.30 0.40 1. Stability specifications are included in Absolute Accuracy values for the primary specifications.. The 7A will drive up to 00 pf of load capacitance. Accuracy specifications include loads to 300 pf and 10 pf as shown under "Load Limits." For capacitances up to the maximum of 00 pf, add "Load Regulation." Voltage Range Maximum Current Limits Load Limits. V [] V 0 V 0 ma, 0 C-40 C 0 ma, 40 C-0 C >0, 00 pf 10 V 6 ma 600 pf 7A Amplifier: 40 Hz- khz 0 ma 00 pf [1] 10 V khz-30 khz 70 ma 300 pf 30 khz-0 khz 70 ma [3] 10 pf 1. The 7A will drive up to 00 pf of load capacitance. Accuracy specifications include loads to 300 pf and 10 pf as shown under "Load Limits." For capacitances up to the maximum of 00 pf, add "Load Regulation.".. V Range, 0 khz-1. MHz only: accuracy specifications cover loads to ma or 00 pf. For higher loads, load regulation is added. 3. Applies from 0 C to 40 C. Output Display Formats... Voltage or dbm, dbm reference 600. Minimum Output... % on each range External Sense... Applicable for. V, V, 0 V, and 10 V ranges; 730A <0 khz, 7A <30 khz. Specifications are the same as internal sense. Fluke Calibration 730A High Performance Multifunction Calibrator
Settling Time to Full Accuracy (Hz) Settling Time (seconds) -10 7 >10 Plus 1 second for amplitude or frequency range change Plus seconds for 730A 10 V range Plus 4 seconds for 7A 10 V range Overshoot...< % Common Mode Rejection... 140 db, dc to 400 Hz Ranges (Hz)...000-119.99 0.100 k - 1.1999 k 1.00 k - 11.999 k 1.00 k - 119.99 k 10.0 k - 1.1999 M Accuracy... 0.01 % Resolution...11.999 counts Phase Lock (Selectable Rear Panel BNC Input) Phase Accuracy (except 10 V range)...>30 Hz: 1 + 0.0 /khz), <30 Hz: 3 Input Voltage...1 V to V rms sine wave (do not exceed 1 V for mv ranges) Range... Hz to 1.1999 MHz Lock Range... % of frequency Lock-In Time...Larger of /frequency or msec Phase Reference (Selectable Rear Panel BNC Output) Range... 10 Phase Accuracy (except 10 V range)... 1 at quadrature points (0, 90, 10 ) elsewhere Stability... 0.1 Resolution...1 Output Level... V rms 0. V Range...0 khz to 1 khz, usable Hz to 1.1999 MHz 000 00 40 Hz 30 Hz Voltage 0 1 Hz Volt-Hertz Capability. x 7 V-Hz 3. V 0 Hz 0 Hz 1 khz 0 khz 1 MHz 30 MHz Figure A. 9 Fluke Calibration 730A High Performance Multifunction Calibrator
Resistance Specifications Nominal Value ( ) 0 1 1.9 19 0 190 1 k 1.9 k k 19 k 0 k 190 k 1 M 1.9 M M 19 M 0 M 0 1 1.9 19 0 190 1 k 1.9 k k 19 k 0 k 190 k 1 M 1.9 M M 19 M 0 M Note: 730A Resistance Specifications Absolute Accuracy of Characterized Value C from calibration temperature [1] Relative Accuracy 1 C 4 Hours 90 Days 10 Days 1 Year 4 Hours 90 Days ppm 99 % Confidence Level 0 3 3 7 7 6 6 7 13 1 33 43 0 40 70 70 0 0... 6 1 7 3 0 9 9 11 11 7. 7. 7 7 14 17 37 47 1 40 0 0 1 1 9 9.7.7.. 7. 7 11 13. 31 39 9 0 0 0 6 6 11. 11. 7. 7. 7. 7. 9 11 14. 19 40 0 11 9 % Confidence Level 40 9. 9. 6 6 6 6 1 1 34 4 0 1. Specifications apply to displayed value. 4-wire connections, except 0 M. 0 1 1 7 7 1 1 1 1 1 46 10 40 9 9 3 3 6. 6. 6. 6... 13 1 40 47 0 0 3 4. 3 0 0 40 7 0 4 3. 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6. 16 40 0 40 33 7 4 4 3 3 3 3 3 3 6 14 4 60 40 3 6 7 6 3. 3....... 4 4 1 0 0 Fluke Calibration 730A High Performance Multifunction Calibrator
Nominal Value ( ) Resistance Secondary Performance Specifications and Operating Characteristics Stability 1 C [1] 4 Hours Temperature Coefficient Adder [] Full Spec Load Range [3] I L - I U (ma) Maximum Peak Current I MAX (ma) Maximum Difference of Characterized to Nominal Value Two-Wire Adder Active Compensation [4] 0 - C Lead Resistance - 40 C and 40-0 C 0.1 1 ppm ppm ppm/ C m 0-00 00 + I m 4 + I m 1 3 4-0 700 00 + I m 1.9 6 7-0 00 00 + I m 3-11 0 300 + I m 19 4 3-11 160 300 + I m 0 3-11 70 10 + I m 190 3-11 0 10 + I m 1 k 3 1-10 1 1.9 k 3 1-1. 16 10 1 k 3 0-00 A 7 10 0 60 4 + I m 4 + I m 4 + I m 4 + I m 4 + I m 4 + I m 19 k 3 0-0 A 10 0 10 0 k 3-0 A 1 10 190 k 3-0 A 00 A 10 1 M.. 6-0 A 0 A 00 1.9 M 3. 3. - A 0 A 00 M 0 0. - A A 300 19 M 0 40 0. - 1 A A 300 0 M 0 1 0 0-00 na 1 A 00 1. Stability specifications are included in the Absolute Accuracy values in the primary specification tables. I m = Current produced by Ohmmeter (A). Temperature coefficient is an adder to Accuracy specifications that does not apply unless operated more than C from calibration temperature, or calibrated outside the range 19 C to 4 C. Two examples: - Calibrate at 0 C: Temperature coefficient adder is not required unless operated below 1 C or above C. - Calibrate at 6 C: Add C temperature coefficient adder. Additional temperature coefficient adder is not required unless operated below 1 C or above 31 C. 3. Refer to current derating factors table for loads outside of this range. 4. Active two-wire compensation may be selected for values less than 0 k, with either the front panel or the meter input terminals as reference plane. Active compensation is limited to 11 ma load, and to V burden. Two-wire compensation can be used only with -meters that source continuous (not pulsed) dc current. 11 Fluke Calibration 730A High Performance Multifunction Calibrator
Nominal Value ( ) Current Derating Factors Value of Derating Factor K for Over or Under Current Four-Wire I < IL [1] Two-Wire Comp I < IL [1] Four-Wire IU < I < IMAX [] SHORT 1 1.9 4.4 4.4 4.4 19 0 190 1 k 1.9 k k 19 k 0 k 190 k 1 M 1.9 M M 19 M 0 M 4.4 4.4 4.4 4.4 4.4 4.4 000 000 30 16 3.. 0.4 0.4 0 0 7. 4.0 1.0 0.3 0. 0.3 0.1 1.6 x -3 3 x -3 1 x - 1.9 x - 0.1 0.19.0 3. x - 3. x - 1. x -4.9 x -4 1 x -3 1.9 x -3 1. For I < I L, errors occur due to thermally generated voltages within the 730A. Use the following equation to determine the error, and add this error to the corresponding accuracy or stability specification. Error = K(I L - I)/( I L x I) Where: Error is in m for all two-wire comp values and four-wire short, and in ppm for the remaining four-wire values. K is the constant from the above table; I and IL are expressed in ma for short to 1.9 k ; I and IL are expressed in A for k to 0 M. For I U < I < I MAX errors occur due to self-heating of the resistors in the calibrator. Use the following equation to determine the error in ppm and add this error to the corresponding accuracy or stability specification. Error in ppm = K(I -I U ) Where: K is the constant from the above table; I and I U are expressed in ma for short to 19 k ; I and I U are expressed in A for 0 k to 0 M 0.3 300 160 4 x - 1. x -4 1 Fluke Calibration 730A High Performance Multifunction Calibrator
DC Current Specifications 730A DC Current Specifications Absolute Accuracy C from calibration temperature Relative Accuracy 1 C Resolution Range 4 Hours 90 Days 10 Days 1 Year 4 Hours 90 Days na (ppm output + na) 99 % Confidence Level 0 A. ma ma 0.1 1 40 + 7 30 + 30 + 0 4 + 7 3 + 3 + 0 4 + 7 37 + 37 + 0 0 + 7 40 + 40 + 0 4 + 4 + 4 + 0 6 + 6 + 6 + 0 A (ppm output + A) 0 ma [1] 0.1. A [1] 1 40 + 0. 60 + 1 4 + 0. 70 + 1 47 + 0. 0 + 1 0 + 0. 90 + 1 6 + 0.3 40 + 7 30 + 0.3 4 + 7 7A Amplifier: 11 A 330 + 470 340 + 40 30 + 40 360 + 40 0 + 130 1 + 130 9 % Confidence Level na (ppm output + na) 0 A. ma ma 0.1 1 A 0 ma [1] 0.1. A [1] 1 3 + 6 + 7 + 40 3 + 0.7 0 + 1 3 + 6 30 + 7 30 + 40 40 + 0.7 60 + 1 37 + 6 33 + 7 33 + 40 40 + 6 3 + 7 3 + 40 (ppm output + A) 4 + 0.7 4 + 0.7 70 + 1 0 + 1 0 + 1.6 0 + 4 0 + 40 + 0. 3 + 6 + 1.6 + 4 + 40 + 0. 40 + 6 7A Amplifier: 11 A 330 + 470 340 + 40 30 + 40 360 + 40 0 + 130 1 + 130 Note: Maximum output from the calibrator s terminals is. A. Accuracy specifications for 0 A and. ma ranges are increased by a factor of 1.3 when supplied through 7A terminals. Specifications are otherwise identical for all output locations. 1. Add to accuracy specifications: 00 x I ppm for >0 ma on 0 ma range x I ppm for >1 A on. A range DC Current Secondary Performance Specifications and Operating Characteristics Temperature Noise Stability Coefficient [] 1 C [1] Bandwidth 4 Hours - 40 C 0.1- Hz Maximum Load for Full Accuracy [4] Burden 0 - C Bandwidth Compliance Range and Voltage Hz- khz Limits 40-0 C Adder [3] pk-pk RMS (ppm ( na/v) ppm output output + na) (ppm output + na) / C ( ) + na na 0 A + 1 1 + 0.40 3 + 1 0. 0k 6 +.9. ma + 1 + 3 + 0. k 6 + ma + 0 1 + 0 3 + 0 00 6 + 0 0 0 ma + 300 1 + 00 3 + 1 A 0 0 9 + 300 00. A 9 + 7 A 1 +. A 3 + A 3 [] A 1 + 1. A 0 A 7A (ppm ppm output output + A) (ppm output + A)/ C + A A 11 A + 0 0 + 7 30 + 10 4 0 4 1 + 70 17 Maximum output from the calibrator s terminals is. A. Accuracy specifications for 0 ma and. ma ranges are increased by a factor of 1.3 when supplied through 7A terminals. 1. Stability specifications are included in the Absolute Accuracy values for the primary specifications.. Temperature coefficient is an adder to Accuracy specifications. It does not apply unless operating more than C from calibration temperature. 3. Burden voltage adder is an adder to Accuracy specifications that does not apply unless burden voltage is greater than 0. V. 0.1x actual load 4. For higher loads, multiply Accuracy specification by: 1 maximum load for full accuracy. The calibrator s compliance limit is V for outputs from 1 A to. A. 7A Amplifier may be used in range-lock mode down to 0 A. Minimum Output... 0 for all ranges, including 7A. Settling Time... 1 second for ma and ma ranges; 3 seconds for. A range; 6 seconds for 11 range; + 1 second for range or polarity change Overshoot... < % 13 Fluke Calibration 730A High Performance Multifunction Calibrator
AC Current Specifications Range 0 A 1 na. ma na ma 0 na 0 ma 1 A. A A 11 A 0 A Resolution (Hz) 730A AC Current Specifications: 99 % Confidence Level k - k k - k k - k k - k 0-1 k k - k k - k Absolute Accuracy C from calibration temperature Relative Accuracy 1 C 4 Hours 90 Days 10 Days 1 Year 4 Hours 90 Days (ppm output + na) 60 + 0 170 + 1 11 + 300 + 1 00 + 0 60 + 0 170 + 40 11 + 40 + 130 00 + 00 60 + 00 170 + 400 11 + 400 + 700 00 + 6000 60 + 170 + 4 11 + 3 + 4 00 + 1 70 + 40 440 + 0 6000 + 00 0 + 0 10 + 1 117 + 30 + 1 10 + 0 0 + 0 10 + 40 117 + 40 0 + 130 10 + 00 0 + 00 10 + 400 117 + 400 0 + 700 10 + 6000 0 + 10 + 4 117 + 3 0 + 4 10 + 1 0 + 40 460 + 0 7000 + 00 7A Amplifier: 370 + 170 00 + 30 3000 + 70 400 + 170 0 + 30 3300 + 70 90 + 0 190 + 1 11 + 340 + 1 100 + 0 90 + 0 190 + 40 11 + 40 30 + 130 100 + 00 90 + 00 190 + 400 11 + 400 30 + 700 100 + 6000 300 + 0 00 + 1 10 + 30 + 1 1300 + 0 300 + 0 00 + 40 10 + 40 40 + 130 1300 + 00 300 + 00 00 + 400 10 + 400 40 + 700 1300 + 6000 (ppm output + A) 90 + 300 + 190 + 4 00 + 4 11 + 3 10 + 3 30 + 4 40 + 4 100 + 1 1300 + 1 90 + 40 40 + 0 700 + 00 440 + 170 900 + 30 300 + 70 300 + 40 00 + 0 000 + 00 460 + 170 90 + 30 3600 + 70 60 + 0 130 + 1 0 + 0 + 1 900 + 0 60 + 0 130 + 40 0 + 40 190 + 130 900 + 00 60 + 00 130 + 400 0 + 400 190 + 700 900 + 6000 60 + 130 + 4 0 + 3 190 + 4 900 + 1 60 + 40 40 + 0 6000 + 00 300 + 170 700 + 30 00 + 70 0 + 0 10 + 1 1 + 0 + 1 00 + 0 0 + 0 10 + 40 1 + 40 0 + 130 00 + 00 0 + 00 10 + 400 1 + 400 0 + 700 00 + 6000 0 + 10 + 4 1 + 3 0 + 4 00 + 1 0 + 40 440 + 0 7000 + 00 330 + 170 00 + 30 300 + 70 Note: Maximum output from the calibrator s terminals is. A. Accuracy specifications for 0 A and. ma ranges are increased by a factor of 1.3 plus A when supplied through 7A terminals. libration Fluke 730A Extended Specifications 14 Fluke Calibration 730A High Performance Multifunction Calibrator
730A AC Current Specifications: 9 % Confidence Level Absolute Accuracy C from calibration Range Resolution temperature Relative Accuracy 1 C (Hz) 4 Hours 90 Days 10 Days 1 Year 4 Hours 90 Days (ppm output + na) 0 A 1 na k - k + 16 130 + 96 + 40 + 1 00 + 6 30 + 16 140 + 99 + 0 + 1 900 + 6 40 + 16 10 + 1 + 70 + 1 00 + 6 0 + 16 160 + 3 + 0 + 1 10 + 6 + 16 1 + 0 + 00 + 1 700 + 6 30 + 16 130 + 90 + 30 + 1 00 + 6. ma na ma 0 na 0 ma 1 A. A A 7A Amplifier: 11 A 0 A k - k k - k k - k 0-1 k k - k k - k + 40 130 + 3 96 + 3 170 + 1 00 + 60 + 400 130 + 30 96 + 30 170 + 0 00 + 000 + 4 130 + 3. 96 +. 170 + 3. 00 + 14 + 3 30 + 0 000 + 160 370 + 170 00 + 30 3000 + 70 30 + 40 140 + 3 99 + 3 10 + 1 900 + 60 30 + 400 140 + 30 99 + 30 10 + 0 900 + 000 30 + 4 140 + 3. 99 +. 10 + 3. 900 + 4 + 3 390 + 0 6000 + 160 400 + 170 0 + 30 3300 + 70 40 + 40 10 + 3 1 + 3 190 + 1 00 + 60 40 + 400 10 + 30 1 + 30 190 + 0 00 + 000 0 + 40 160 + 3 3 + 3 00 + 1 10 + 60 0 + 400 160 + 30 3 + 30 00 + 0 10 + 000 (ppm output + A) 40 + 4 0 + 4 10 + 3. 160 + 3. 1 +. 3 +. 190 + 3. 00 + 3. 00 + 10 + 34 + 3 40 + 0 600 + 160 440 + 170 900 + 30 300 + 70 44 + 3 40 + 0 7000 + 160 460 + 170 90 + 30 3600 + 70 + 40 1 + 3 0 + 3 160 + 1 700 + 60 + 400 1 + 30 0 + 30 160 + 0 700 + 000 + 4 1 + 3. 0 +. 160 + 3. 700 + 00 + 3 300 + 0 000 + 160 300 + 170 700 + 30 00 + 70 30 + 40 130 + 3 90 + 3 170 + 1 00 + 60 30 + 400 130 + 30 90 + 30 170 + 0 00 + 000 30 + 4 130 + 3. 90 +. 170 + 3. 00 + 30 + 3 30 + 0 6000 + 160 330 + 170 00 + 3 300 + 70 Note: Maximum output from the calibrator s terminals is. A. Accuracy specifications for 0 A and. ma ranges are increased by 1.3 plus A when supplied through 7A terminals. 1 Fluke Calibration 730A High Performance Multifunction Calibrator
Range 0 A. ma ma 0 ma. A 11 A AC Current Secondary Performance Specifications and Operating Characteristics (Hz) k - k k - k k - k Hz k - k 0-1 k k - k k - k Stability 1 C [1] 4 Hours Temperature Coefficient [] - 40 C 0 - C and 40-0 C (ppm output + na) (ppm output + na)/ C 10 + 0 + 0 + 0 + 0 + 0 + 30 + 3 4 + 0. + 0. 0 + 0 + 1 0 + 1 400 + 0 0 + 0 0 + 0 10 + 0 + 0 + 0 + 0 + 4 0 + 4 30 + 3 4 + 1 + 0 + 0 + 0 0 + 0 400 + 0 0 + 400 0 + 400 10 + 0 0 + 0 + 0 + 0 0 + 0 + 30 + 30 4 + + 0 0 + 00 + 00 0 + 400 400 + 00 0 + 00 0 + 00 (ppm output + (ppm output + A)/ C A) 10 + 0. 0 + 0.0 0 + 0.0 0 + 0. 0 + 0.0 0 + 0.0 30 + 0.3 4 + 0.1 + 0.1 0 + 3 + 0 + 400 + 0 + 0 + 0 + 4 + 1 + 1 0 + 0 + 0 + 00 + 0 0 + 0 + 7A Amplifier: 7 + 0 0 + 10 00 + 300 0 + 7 40 + 7 0 + 7 30 + 7 0 + 7 0 + 7 Compliance Limits (V rms) Maximum Resistive Load For Full Accuracy [3] ( ) 7 k 7 00 7 0 7 1.4 [4] 0. 3 3 Noise and Distortion (Bandwidth Hz - 0 khz <0.V Burden) (% output + A) 0.0 + 0.1 0.0 + 0.1 0.0 + 0.1 0. + 0. 00. + 1 0.0 + 0.1 0.0 + 0.1 0.0 + 0.1 0. + 0. 00. + 1 0.0 + 0.1 0.0 + 0.1 0.0 + 0.1 0. + 0. 00. + 1 0.0 + 0.0 + 0.0 + 0. + 0 00. + 0 0. + 0 0.3 + 00 1 + 1 ma (% output) 0.0 [] 0.1 [] 0. [] Maximum output from 730A terminals is. A. Accuracy specifications for 0 A and. ma ranges are increased by a factor of 1.3, plus A when supplied through 7A terminals. Specifications are otherwise identical for all output locations. 1. Stability specifications are included in the Absolute Accuracy values for the primary specifications.. Temperature coefficient is an adder to accuracy specifications that does not apply unless operating more than C from calibration temperature. actual load 3. For larger resistive loads multiply accuracy specifications by: ( ) maximum load for full accuracy 4. 1. V compliance limit above 1 A. 7A Amplifier may be used in range-lock mode down to 1 A.. For resistive loads within rated compliance voltage limits. Minimum Output...9 A for 0 A range, % on all other ranges. 1 A minimum for 7A. Inductive Load Limits...400 H (730A, or 7A). 0 H for 730A output >1 A. Power Factors... 730A, 0.9 to 1; 7A, 0.1 to 1. Subject to compliance voltage limits. Range (Hz)...000-11.999, 1.00-119.99, 10.0-1199.9, 1.00 k -.000 k Accuracy... 0.01 % of output Resolution...11,999 counts Settling Time... seconds for 730A ranges; 6 seconds for 7A 11 A range; +1 second for amplitude or frequency range change. Overshoot...< % 16 Fluke Calibration 730A High Performance Multifunction Calibrator
Wideband AC Voltage (Option 700-03) Specifications Specifications apply to the end of the cable and 0 termination used for calibration. Absolute Accuracy Range C from calibration temperature Resolution 30 Hz - 00 khz Volts dbm 4 Hours 90 Days 10 Days 1 Year (% output + V) 1.1 mv -46 nv 0.4 + 0.4 0. + 0.4 0.6 + 0.4 0. + 3.3 mv -37 nv 0.4 + 1 0.4 + 1 0. + 1 0.7 + 3 11 mv -6 0 nv 0. + 4 0.3 + 4 0. + 4 0.7 + 33 mv -17 0 nv 0. + 0.3 + 0.4 + 0.6 + 16 1 mv -6. 1 V 0. + 40 0.3 + 40 0.4 + 40 0.6 + 40 330 mv +3.4 1 V 0. + 0 0. + 0 0.3 + 0 0. + 0 1.1 V +14 V 0. + 400 0. + 400 0.3 + 400 0. + 400 3. V +4 V 0.1 + 00 0. + 00 0.3 + 00 0.4 + 00 (Hz) Resolution (Hz) Amplitude Flatness, 1 khz Reference Voltage Range 1.1 mv 3.3 mv >3.3 mv (% output + floor indicated) Temperature Coefficient ppm/ C Settling Time To Full Accuracy (Seconds) Harmonic Distortion (db) - 30 0.01 0.3 0.3 0.3 0 7-40 30-119.99 0.01 0.1 0.1 0.1 0 7-40 10-1.1999 k 0.1 0.1 0.1 0.1 0-40 1. k - 11.999 k 1 0.1 0.1 0.1 0-40 1 k - 119.99 k 0.1 0.1 0.1 0-40 10 k - 1.1999 M 0 0. + 3 V 0.1 + 3 V 0.1 + 3 V 0-40 1. M - M [1] 0 k 0. + 3 V 0.1 + 3 V 0.1 + 3 V 0 0. -40 M - 11.9 M 0 k 0.4 + 3 V 0.3 + 3 V 0. + 3 V 0 0. -40 1 M - 0 M 1 M 0.6 + 3 V 0. + 3 V 0.4 + 3 V 10 0. -34 0 M - 30 M 1 M 1. + 1 V 1. + 3 V 1 + 3 V 300 0. -34 Note: 1. For output voltages <0 % of full range in the 33 mv, 1 mv, 330 mv, 1.1 V, and 3. V ranges, add 0.1 % to the amplitude flatness specification. Additional Operating Information: dbm reference = 0 Range boundaries are at voltage points, dbm levels are approximate. Power dbm = log ( ) ; 0.361 V across 0 = 1 mw or 0 dbm 1mW Minimum Output...300 V (-7 dbm) Accuracy... 0.01 % of output Resolution...11,999 counts to 1.1999 MHz, 119 counts to 30 MHz Overload Protection...A short circuit on the wideband output will not result in damage. After settling time, normal operation is restored upon removal. 10A Specifications when Operated with the 730A Line Power Voltage range...0 V to 40 V...47 to 63 Hz Voltage variations... % about line voltage Power consumption...<100 VA Transient overvoltage...impulse withstand (overvoltage) Category II of IEC 60364-4-443 Dimensions (HxWxL) With feet...19 mm x 43 mm x 64 mm (7.6 in x 17.0 in x. in) Without feet...17 mm x 43 mm x 64 mm (7.0 in x 17.0 in x. in) Weight... kg (4 lb) Temperature Operating... C to 3 C (41 F to 9 F) Calibration (tcal)...16 C to 30 C (61 F to 6 F) Storage...0 C to 0 C (3 F to 1 F) Transit...-0 C to +60 C (-4 F to +140 F) <0 hours 17 Fluke Calibration 730A High Performance Multifunction Calibrator
Warmup Time... Twice the time since last warmed up, to a maximum of 1 hour. Humidity (non-condensing) Operating... <0 %, C to 31 C (41 F to F) ramping linearly down to 0 % at 3 C (9 F) Storage... <9 %, 0 to 0 C (3 F to 1 F) Altitude Operating...,00 m (,00 ft) maximum Non-Operating... 1,000 m (39,400 ft) maximum Shock and Vibration... MIL-PRF-00F Class 3 Safety... EN/IEC 6-1, 300 V CAT II, Pollution Degree Electromagnetic Environment... IEC 6136-1, Industrial Electromagnetic Compatibility... FCC Rules part 1 sub part B Applies to use in Korea only. Class A Equipment (Industrial Broadcasting & Communication Equipment) [1] [1] This product meets requirements for industrial (Class A) electromagnetic wave equipment and the seller or user should take notice of it. This equipment is intended for use in business environments and is not to be used in homes. Indoor use only... IP0 10A Electrical Performance Limits Voltage compliance developed across inductive loads may prevent range maximum current output being achieved at higher frequencies. The appropriate maximum frequency (Fmax) for a given load inductance and current is given by: Fmax = 4. I = Current I L L = Total inductance The maximum frequency calculated with this equation is only approximate. Series resistance and parallel capacitance also affect the maximum achievable frequency. Input Common Mode Rejection... 0 db @ DC decreasing linearly to 40 db at khz Input Impedance Voltage input... >1 M Current input... Maximum Output Compliance Voltage... 4. V rms (6.4 V pk), 6.4 V dc. 10 A range maximum compliance voltage decreases from 4. V at 1 khz to about 3 V at khz DC Offset... Magnetic remanence that follows abrupt changes in output current level may cause small changes to DC current offset. It is good practice to correct for offsets in DC measurements and techniques such as DC reversal measurement will result in best accuracy. Operated within 730A Control Loop (all current ranges) The current accuracy of the 10A, when controlled by a single 730A, applies to the parallel output of up to three 10As connected as slaves. Coverage factor k=. (99 % confidence level) Current Accuracy 1-year accuracy, tcal [1] C (% of output + % of range) 730A % of output % of range DC 0.01 0.0 Hz to 0 Hz 0.011 0.003 0 Hz to 6 khz 0.0 0.00 6 khz to khz See Operated Stand Alone current accuracy table in the 10A Users Manual. 1. tcal is the temperature at which calibration adjustment took place. Maximum inductance for stability LCOMP OFF is 0 H. Maximum inductance for stability LCOMP ON is 400 H for A and 0 A ranges. 0 H on the 10 A range. With LCOMP ON, the output is limited to 7.e3 A-Hz. For example, a 0 A output is limited to 7 Hz. 1 Fluke Calibration 730A High Performance Multifunction Calibrator
Coverage factor k=.00 (9 % confidence level) Current Accuracy 1-year accuracy, tcal [1] C (% of output + % of range) 730A % of output % of range DC 0.01 0.00 Hz to 0 Hz 0.009 0.00 0 Hz to 6 khz 0.040 0.004 6 khz to khz See Operated Stand Alone current accuracy table in the 10A Users Manual. 1. tcal is the temperature at which calibration adjustment took place. Maximum inductance for stability LCOMP OFF is 0 H. Maximum inductance for stability LCOMP ON is 400 H for A and 0 A ranges. 0 H on the 10 A range. With LCOMP ON, the output is limited to 7.e3 A-Hz. For example, a 0 A output is limited to 7 Hz. Maximum Distortion and Noise Distortion [1] Noise LCOMP OFF LCOMP ON 16 Hz to MHz dbc Current dbc Current Amp Range 16 Hz to 0 Hz -76 4 A -70 3 A -60 db 0 Hz to 6 khz - 66 A -46 1.3 ma -60 db 6 khz to khz [] -40.6 ma -3 4.7 ma -60 db 0 Amp Range 16 Hz to 0 Hz -76 41 A -60.6 ma -70 db 0 Hz to 6 khz - 6.6 ma -4 0.9 ma -70 db 6 khz to khz [] -40 6.4 ma -3 46.9 ma -70 db 10 Amp Range 16 Hz to 0 Hz -76. ma -60 1. ma -70 db 0 Hz to 6 khz - 39.7 ma -4 1.7 ma -70 db 6 khz to khz [] -40 1. ma -3 1.3 ma -70 db 1. Use db or Current. Whichever is larger.. Interharmonics only above 6 khz. 10A/COIL 3 KA -Turn Coil Number of Turns... Minimum internal jaw dimension to clear wires 6 mm (width) x 36 mm (length) Maximum Input Current...10 A continuous with built-in 1 V fan on Maximum Voltage...4. V rms Accuracy Input Current [1] Effective Current Amp-turns 10A + Coil Accuracy [] (% of Amp-turns + % of 10A range) % of Amp-turns % of 10A Range 0 A to 0 A DC 0 to 00 0.7 % 0.7 % 0 A to 10 A Hz to 6 Hz 0 to 3000 0.7 % 0.7 % 0 A to 10 A 6 Hz to 300 Hz 0 to 3000 0.7 % 0.7 % 0 A to 40 A 300 Hz to 1 khz 0 to 00 0.7 % 0.7 % 0 A to 1 A 1 khz to 3 khz 0 to 300 0. % 1.0 % 0 A to 3 A 3 khz to 6 khz 0 to 7 1. % 1.0 % 0 A to 1 A 6 khz to khz 0 to.0 % 1.0 % 1. The inductance and mutual inductance of the turn coil and clamp that is measured causes a frequency dependent compliance voltage across the coil. The length and configuration of the cables that connect the current to the coil also have an effect. Maximum input current is 10 A input at approximately 0 Hz. Maximum current input decreases to approximately 0. A at khz.. Includes coil/clamp interaction. 19 Fluke Calibration 730A High Performance Multifunction Calibrator
10A/COIL 6 KA 0-Turn Coil Number of Turns... 0 Minimum Flexible Probe Length... 00 mm Maximum Input Current... 10 A continuous with built-in 1 V fan on Maximum Voltage... 4. V rms Input Current [1] Accuracy Effective Current Amp-turns 10A + Coil Accuracy [] (% of Amp-turns + % of 10A range) % of Amp-turns % of 10A Range 0 A to 0 A DC 0 to 000 0.7 % 0.7 % 0 A to 10 A Hz to 6 Hz 0 to 6000 0.7 % 0.7 % 0 A to 10 A 6 Hz to 300 Hz 0 to 6000 0.7 % 0.7 % 0 A to 10 A 300 Hz to 1 khz 0 to 6000 0.7 % 0.7 % 0 A to 10 A 1 khz to 3 khz 0 to 6000 0. % 1.0 % 0 A to A 3 khz to 6 khz 0 to 10 1. % 1.0 % 0 A to 13 A 6 khz to khz 0 to 60.0 % 1.0 % 1. The inductance and mutual inductance of the 0 turn coil causes a frequency dependent compliance voltage across the coil. Maximum frequency for 10 A input current is approximately 600 Hz. Maximum current input decreases to approximately 13 A at khz.. Includes coil/probe interaction. Note The specifications for these coils are at 99 % confidence level and are the combined accuracy of the coil and a 10A. If the coils are used with other current sources the calibration accuracy of the coils alone is 0.6 % (99 % confidence level) from 0 Hz to khz. Operating Limits Output Current Range A 0 A 10 A Current Output (Max.) A rms 0 A rms 10 A rms Current Input Input Current (Max.) 00 ma rms 00 ma rms 10 ma rms Current gain 0 1,000 Voltage Input Input Voltage (Max.) V rms V rms 1. V rms Transconductance 1 Siemen Siemens 0 Siemens 10 A Range Current/ Limits Maximum Output Current Maximum Current Input Maximum Voltage Input DC 0 A 0 ma 1.0 V < Hz 0 A pk (70 A rms) 0 ma pk (70 ma rms) 1.0 V pk (0.7 V rms) Hz to khz 170 A pk (10 A rms) 170 ma pk (10 ma rms) 1.7 V pk (1. V rms) Note: The A and 0 A ranges operate at full output current from DC to khz. Output Isolation Maximum Voltage Signal Applied to any Output Current Terminal with respect to Earth DC to 0 Hz 600 V rms, 0 V pk, limited A rms, no transient overvoltages 0 Hz to 3 khz 0 V rms, 14 V pk, limited A rms, no transient overvoltages 3 khz to khz 33 V rms, 47 V pk, limited A rms, no transient overvoltages 0 Fluke Calibration 730A High Performance Multifunction Calibrator
Ordering Information Model 730A Multifunction Calibrator 730A/03 Multifunction Calibrator with Wideband AC Voltage Option 730A/S Multifunction Calibrator with no front panel USB port Accessories 10A Transconductance Amplifier 7A Amplifier 730A-700 Low Thermal EMF Cables with Banana Plugs 730A-7003 Low Thermal EMF Cables with Spade Connectors Y737 730A Rack Mount Kit Y73 730A Rack Ear Kit 7XX/CASE 730A Durable Travel Case Additional standards 790A AC Measurement Standard 734A Voltage Reference and DC Voltage Standard 73B Direct Voltage Standard 74A Resistance Standards 79A AC/DC Transfer Standard Software MET/CAL MET/TEAM MET/CAL Plus Calibration Management Software MET/TEAM Test Equipment Asset Management Software Fluke Calibration. Precision, performance, confidence. Fluke Calibration PO Box 9090, Everett, WA 906 U.S.A. Fluke Europe B.V. PO Box 116, 60 BD Eindhoven, The Netherlands Web access: http://www.flukecal.en For more information call: In the U.S.A. (77) 3-3 or Fax (4) 446-116 In Europe/M-East/Africa +31 (0) 40 67 00 or Fax +31 (0) 40 67 In Canada (00)-36-FLUKE or Fax (90) 90-666 From other countries +1 (4) 446-00 or Fax +1 (4) 446-116 Web access: http://www.flukecal.com 013 Fluke Calibration. Specifications subject to change without notice. Printed in U.S.A. /013 4639A_EN Pub-ID: 1117-eng 1 Fluke Calibration 730A High Performance Multifunction Calibrator Modification of this document is not permitted without written permission from Fluke Calibration.