Power Exhaust on JET: An Overview of Dedicated Experiments

Similar documents
Divertor power deposition and target current asymmetries during type-i ELMs in ASDEX Upgrade and JET

Power Deposition Measurements in Deuterium and Helium Discharges in JET MKIIGB Divertor by IR-Thermography

Steady State and Transient Power Handling in JET

ELM filament heat loads on plasma facing components in JET and ITER

Effect of ExB Driven Transport on the Deposition of Carbon in the Outer Divertor of. ASDEX Upgrade

Erosion and Confinement of Tungsten in ASDEX Upgrade

L-Mode and Inter-ELM Divertor Particle and Heat Flux Width Scaling on MAST

DIVIMP simulation of W transport in the SOL of JET H-mode plasmas

Edge Plasma Energy and Particle Fluxes in Divertor Tokamaks

Radiative type-iii ELMy H-mode in all-tungsten ASDEX Upgrade

Erosion and Confinement of Tungsten in ASDEX Upgrade

Divertor Heat Load in ITER-Like Advanced Tokamak Scenarios on JET

Turbulent Transport Analysis of JET H-mode and Hybrid Plasmas using QuaLiKiz, TGLF and GLF23

Progress in Turbulence Modeling JET SOL and edge phenomena

Modelling of Carbon Erosion and Deposition in the Divertor of JET

Tungsten: An option for divertor and main chamber PFCs in future fusion devices

Studies of the Quiescent H-mode regime in ASDEX Upgrade and JET

L-mode radiative plasma edge studies for model validation in ASDEX Upgrade and JET

Confinement and edge studies towards low ρ* and ν* at JET

EX/4-2: Active Control of Type-I Edge Localized Modes with n = 1 and n = 2 fields on JET

Influence of Impurity Seeding on ELM Behaviour and Edge Pedestal in ELMy H-Mode Discharges

Divertor Power Handling Assessment for Baseline Scenario Operation in JET in Preparation for the ILW

Direct measurements of the plasma potential in ELMy H mode. plasma with ball pen probes on ASDEX Upgrade tokamak

Divertor power and particle fluxes between and during type-i ELMs in ASDEX Upgrade

Turbulence and transport reduction with innovative plasma shapes in TCV - correlation ECE measurements and gyrokinetic simulations

Divertor Detachment on TCV

Improved Plasma Confinement by Ion Bernstein Waves (IBWs) Interacting with Ions in JET

1 EX/3-5. Material Erosion and Redeposition during the JET MkIIGB-SRP Divertor Campaign

EXD/P3-23. Fluctuations, ELM Filaments and Turbulent Transport in the SOL at the Outer Midplane of ASDEX Upgrade

Fusion Nuclear Science Facility (FNSF) Divertor Plans and Research Options

Integrated Core-SOL-Divertor Modelling for ITER Including Impurity: Effect of Tungsten on Fusion Performance in H-mode and Hybrid Scenario

Review of experimental observations of plasma detachment and of the effects of divertor geometry on divertor performance

Be tile power handling and main wall protection

Experimental Study of the Stability of Alfvén Eigenmodes on JET

MHD Induced Fast-Ion Losses in ASDEX Upgrade

Hydrocarbon transport in the MkIIa divertor of JET

Global migration of impurities in tokamaks: what have we learnt?

Non-linear modeling of the Edge Localized Mode control by Resonant Magnetic Perturbations in ASDEX Upgrade

Divertor Requirements and Performance in ITER

Active and Fast Particle Driven Alfvén Eigenmodes in Alcator C-Mod

Scaling of divertor heat flux profile widths in DIII-D

Mitigation of ELMs and Disruptions by Pellet Injection

The performance of improved H-modes at ASDEX Upgrade and projection to ITER

Multi-machine comparisons of divertor heat flux mitigation by radiative cooling with nitrogen

Improved EDGE2D-EIRENE Simulations of JET ITER-like Wall L-mode Discharges Utilising Poloidal VUV/visible Spectral Emission Profiles

Correlations of ELM frequency with pedestal plasma characteristics

EX8/3 22nd IAEA Fusion Energy Conference Geneva

ArbiTER studies of filamentary structures in the SOL of spherical tokamaks

Progressing Performance Tokamak Core Physics. Marco Wischmeier Max-Planck-Institut für Plasmaphysik Garching marco.wischmeier at ipp.mpg.

GA A25410 DISRUPTION CHARACTERIZATION AND DATABASE ACTIVITIES FOR ITER

Current density modelling in JET and JT-60U identity plasma experiments. Paula Sirén

The physics of the heat flux narrow decay length in the TCV scrape-off layer: experiments and simulations

Experimental Evidence of Inward Momentum Pinch on JET and Comparison with Theory

Upgrade of the Present JET Shape and Vertical Stability Controller

ARTICLES PLASMA DETACHMENT IN JET MARK I DIVERTOR EXPERIMENTS

Scaling of divertor heat flux profile widths in DIII-D

ELMs, strike point jumps and SOL currents

Introduction to Fusion Physics

ITER A/M/PMI Data Requirements and Management Strategy

Steady State, Transient and Off-Normal Heat Loads in ARIES Power Plants

Characteristics of the H-mode H and Extrapolation to ITER

Comparison of theory-based and semi-empirical transport modelling in JET plasmas with ITBs

ITER. Power and Particle Exhaust in ITER ITER

Internal Transport Barrier Triggering by Rational Magnetic Flux Surfaces in Tokamaks

Temperature measurement and real-time validation

Triggering Mechanisms for Transport Barriers

Spatio-temporal investigations on the triggering of pellet induced ELMs

Dimensionless pedestal identity plasmas on Alcator C-Mod C

ITR/P1-19 Tokamak Experiments to Study the Parametric Dependences of Momentum Transport

3D analysis of impurity transport and radiation for ITER limiter start-up configurations

STUDY OF ADVANCED TOKAMAK PERFORMANCE USING THE INTERNATIONAL TOKAMAK PHYSICS ACTIVITY DATABASE

Partial detachment of high power discharges in ASDEX Upgrade

Impurity Seeding in ASDEX Upgrade Tokamak Modeled by COREDIV Code

Evidence for enhanced main chamber wall plasma loads in JET ITER-like Wall at high radiated fraction

Blob sizes and velocities in the Alcator C-Mod scrapeoff

Dimensionless Identity Experiments in JT-60U and JET

Development of an experimental profile database for the scrape-off layer

Overview of edge modeling efforts for advanced divertor configurations in NSTX-U with magnetic perturbation fields

ASCOT simulations of electron energy distribution at the divertor targets in an ASDEX Upgrade H-mode discharge

L-mode filament characteristics on MAST as a function of plasma current measured using visible imaging

Highlights from (3D) Modeling of Tokamak Disruptions

Characterization of Tungsten Sputtering in the JET divertor

II: The role of hydrogen chemistry in present experiments and in ITER edge plasmas. D. Reiter

INTERNATIONAL ATOMIC ENERGY AGENCY 22 nd IAEA Fusion Energy Conference Geneva, Switzerland, October 2008

Modelling of prompt deposition of tungsten under fusion relevant conditions

L-to-H power threshold comparisons between NBI and RF heated plasmas in NSTX

Recent progress towards a functional model for filamentary SOL transport

ASSESSMENT AND MODELING OF INDUCTIVE AND NON-INDUCTIVE SCENARIOS FOR ITER

Divertor heat & particle flux study in the EAST superconducting tokamak

Experimental results and modelling of ASDEX Upgrade partial detachment

Impact of Carbon and Tungsten as Divertor Materials on the Scrape-off Layer Conditions in JET

1) H-mode in Helical Devices. 2) Construction status and scientific objectives of the Wendelstein 7-X stellarator

EXD/P3-13. Dependences of the divertor and midplane heat flux widths in NSTX

Physics basis for similarity experiments on power exhaust between JET and ASDEX Upgrade with tungsten divertors

Active and Passive MHD Spectroscopy on Alcator C-Mod

ADVANCES IN PREDICTIVE THERMO-MECHANICAL MODELLING FOR THE JET DIVERTOR EXPERIMENTAL INTERPRETATION, IMPROVED PROTECTION, AND RELIABLE OPERATION

Effect ofe B driven transport on the deposition of carbon in the outer divertor of ASDEX Upgrade

Evolution of the pedestal on MAST and the implications for ELM power loadings

Carbon Deposition and Deuterium Inventory in ASDEX Upgrade

Impact of High Field & High Confinement on L-mode-Edge Negative Triangularity Tokamak (NTT) Reactor

Transcription:

Power Exhaust on JET: An Overview of Dedicated Experiments W.Fundamenski, P.Andrew, T.Eich 1, G.F.Matthews, R.A.Pitts 2, V.Riccardo, W.Sailer 3, S.Sipila 4 and JET EFDA contributors 5 Euratom/UKAEA Fusion Association, Culham Science Centre, Abingdon, OX14 3DB, UK 2) CRPP-EPFL, Association Euratom-Confédération Suisse, CH-1015 Lausanne, Switzerland 3) Universität Innsbruck, Technikerstraße 25, A-6020 Innsbruck, Austria 4) Helsinki U. of Technology, Tekes-Euratom Assoc., PO Box 2200, FIN-02015 HUT, Finland 5) See annex to J. Pamela, Fus. Energy 2002 (Proc. 19th Int. Conf. Lyon, 2002), IAEA, Vienna followed by Wall and Divertor Load during ELMy H-mode and Disruptions in ASDEX Upgrade A. Herrmann, J. Neuhauser, G. Pautasso, V. Bobkov, R. Dux, T. Eich, C.J. Fuchs, O. Gruber, C. Maggi, H.W. Müller, V. Rohde, M. Y. Ye, ASDEX Upgrade team 1 1) Max-Planck-Institut für Plasmaphysik, EURATOM-Association, Boltzmann Str. 2., D-85748, Garching, Germany 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 1

Power Exhaust: Outline Steady-state (inter-elm) fwd-b rev-b Transient (ELMs( ELMs) JET AUG 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 2

Divertor Target Power Deposition: IR, TC, LP 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 3

Forward field (fwd-b) ELMy H-modes: B B B λ qh A(Z) 1.1±0.12 B φ 0.93±0.2 q 95 0.41±0.27 P div 0.48±0.09 n e 0.15 ±0.13 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 4

Comparison with theories of SOL energy transport λ qh A(Z) 1.1±0.12 B φ 0.93±0.2 q 95 0.41±0.27 P div 0.48±0.09 n e 0.15 ±0.13 Scaling and Magnitude consistent with classical ion conduction λ q ~ 2.25 λ q A1 ~ 0.27 λ q A2 χ SOL ~ (1-5) χ A1 as well as collisionally modified ion orbit loss λ q ~2.4ζλ q A1 + (1-ζ)λ q IOL, ζ = v* i / (1 + v* i ) 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 5

Ion orbit loss (ASCOT) profiles: fwd-b B vs. rev-b Very sensitive to field reversal; outer profile broadened 2,0 1,5 1,0 0,5 z (m) 0,0-0,5-1,0-1,5 B x B 2,0 2,5 3,0 3,5 4,0 R (m) 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 6

Reversed field (rev( rev-b) ELMy H-modes: B B Rev-B peak heat flux well matched by fwd-b scaling Radial profiles and transport, insensitive to B B direction! Consistent with neo-classical ion conduction, but not ion orbit loss! ITER prediction ITER prediction: λ q TC ~ 3.7±1.1 mm at entrance to divertor volume 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 7

ELM power exhaust experiments t ~ 125 ± 70 µs ~ τ ~ L / c s,ped 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 8

Advective-diffusive diffusive radial ELM propagation G( t,r ) = A D t exp ( r v t) t τ D t 2 G(r,t) 1.2 1 0.8 0.6 0.4 0.2 0 t=1 t=2 t=3 t=4 t=5 <v > ~ r lim / τ ~ 450-750 m/s <v >/<c s > ~ 0.25-0.4 % 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 9

Comparison with theory: plasmoid propagation model drive mechanism = sheath resistivity, curvature and E B drifts ELM values: δ θ ~ δ r < 10 cm λ n < 12 cm T e,lim ~ 25 ev T i,lim > 75 ev λ Te < 3 cm λ Ti < 8 cm ITER limiter load: λ Te < 3 cm, λ Ti < 6 cm with r lim = 5 cm n e < 3.0x10 19 m -3, T i ~ 2.5T e < 1.0 ± 0.2 kev 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 10

EURATOM - IPP Association, Garching, Germany Wall and Divertor Load during ELMy H- mode and Disruptions in ASDEX Upgrade A. Herrmann, J. Neuhauser, G. Pautasso, V. Bobkov, R. Dux, T. Eich, C.J. Fuchs, O. Gruber, C. Maggi, H.W. Müller, V. Rohde, M. Y. Ye, ASDEX Upgrade team Presented by W. Fundamenski

Global power balance within 20 % but power on main chamber due to hot spots, ELMs and Disruptions 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 12

25% of ELM energy to main chamber wall fair power balance at ~ 90% measured by IR calibrated by TC and calorimetry 10% of ELM energy to inner wall 15% of ELM energy to outer wall ELM radiation? A. Herrmann, PPCF 46(2004)971 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 13

10 to 40 % of ELM energy radiated Mostly in inner divertor Independent of ELM size and density reduction with triangularity tendency to be overbalanced J.C. Fuchs, PSI 2004 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 14

Test limiter probe measures ELM power profile separatrix moved from 2.5 cm to 6.5 cm away from the limiter inter-elm and ELM power decay lengths in the SOL ~ 3-4 cm consistent with v /c s ~ constant, for turbulent eddies and ELMs power decay lengths in the limiter shadow ~ 1-2 cm A. Herrmann, PPCF 46(2004)971 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 15

Helical ELM filaments observed on upper outer divertor and outboard limiter Stripe energy content << 1% of total v tor ELM ~ 350 Hz << 3.5 khz ~ v tor inter-elm Outboard limiter T. Eich, Physical Review Letters, 91 (2003) 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 16

Disruption heat load to main chamber wall density limit disruption ~ 90% lost in thermal quench phase heat deposition fast rise: 0.1-0.5 ms duration: few ms strong broadening on target significant power to non-divertor components. See A. Loarte, this conference 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 17

Conclusions (JET and AUG): Steady state, Type-I ELMy H-mode radial power exhaust on JET dominated by weakly collisional ions experimental data well matched by neo-classical ion conduction predicts tolerable divertor heat loads for ITER Helical ELM structure observed on AUG Type-I ELM radial velocity agrees with sheath limited model (JET) ELM power decay length comparable to outer gap on JET and AUG could pose problems for beryllium limiter on ITER Broad footprint (divertor and first wall) of heat flux deposition during disruption observed on AUG 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 18

Power Exhaust Summary: AUG JET ITER Steady state (inter-elm) Electron Interchange & drift wave turbulence (neo-)classical Total λ ion conduction q ~ 4 mm Transient (intermittent eddies, ELMs) Electron λ qe /R ~ 2 % λ qe /R ~ 1 % λ qe < 3 cm Advection-diffusion Total λ q < 6 cm λ q /R < 2 % 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 19

Characteristic times in the SOL 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 20

N r) N(0) ξ ~ τ τ v cr Kinetic estimates of losses ~ 1, ξ ~ i τ ( τ ( 0 1 = = erf ) = erf ( ξ 2 βv v cr 0 e e βv 2 dv dv 2 βv v e dv W ( r) 0 1 2 1 2 = = erf ( ξ ) ξ exp( ξ ), W (0) 2 2 βv π v e dv 0 2 τ τ i ~ 1, ξ ), e ~ τ τ 0 < ξ < 1 e >> 1 0 < ξ < 1 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 21

Ratio of ion and electron dissipative scales in the SOL 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 22

IR view into the vessel and the limiter positions IR camera view 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 23

ELM ejected particles and energy partly deposited on limiters λ(r) 3-8 mm 30-80 mm (3-7 mm in the limiter shadow) Large variation of ELM signature remote from the separatrix. ELM structure measured at the upper divertor. T. Eich, Physical Review Letters, 91 (2003) ELM resolving diagnostics for non divertor heat load Thermography Langmuir probes Test limiters (M.Y. Ye,PSI 2004) 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 24

Heat flux values at the far edge of the divertor and the leading edge of the limiter are consistent mapped to midplane Plasma λ(r) 7 mm 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 25

Experimental observation of local heat load is qualitatively understood passing banana passing Location of the intersection area depends on ionisation source location, magnetic field helicity, co/counter neutral injection and... on non-axisymetric first wall structure. 2.11.2004 W. Fundamenski, IAEA FEC 2004, Vilamoura, Portugal 26