TOSHIBA MOS Digital Integrated ircuit Silicon Monolithic T466BP/BF/BFN/BFT T466BP,T466BF,T466BFN,T466BFT T466B Quad Bilateral Switch T466B contains four independent circuits of bidirectional switches. When control input ONT is set to H level, the impedance between input and output of the switch becomes low and when it is set to L level, the impedance becomes high. This can be applied for switching of analog signals and digital signals. ON-resistance, Ron 2 Ω (typ.): VDD VSS = V 11 Ω (typ.): VDD VSS = 1 V 7 Ω (typ.): VDD VSS = 1 V OFF-resistance, Roff Roff (typ.) > 1 9 Ω Note: xxxfn (JEDE SOP) is not available in Japan. T466BP T466BF Pin Assignment IN/OUT 1 1 14 OUT/IN 1 2 13 ONT 1 OUT/IN 2 3 12 ONT 4 IN/OUT 2 4 11 IN/OUT 4 ONT 2 1 OUT/IN 4 ONT 3 6 9 OUT/IN 3 7 8 IN/OUT 3 (top view) T466BFN Truth Table ontrol H L Impedance between IN/OUT-OUT/IN. to 1 2 Ω >1 9 Ω (Note) Note: See static electrical characteristics T466BFT Weight DIP14-P-3-2.4 :.96 g (typ.) SOP14-P-3-1.27A :.18 g (typ.) SOP14-P-3-1.27 :.18 g (typ.) SOL14-P-1-1.27 :.12 g (typ.) TSSOP14-P-44-.6A :.6 g (typ.) 1 26-6-1
T466BP/BF/BFN/BFT Logic Diagram 1/4 T466B ONT Absolute Maximum Ratings (Note) haracteristics Symbol Rating Unit D supply voltage. to + 2 V ontrol input voltage V IN. to +. V Switch voltage V. to +. V Potential difference across during ON I ±. V ontrol input current I IN ±1 ma Power dissipation P D 3 (DIP)/18 (SOI) mw Operating temperature range T opr 4 to 8 Storage temperature range T stg 6 to 1 Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in I performance or even destruction. Recommended Operating onditions ( = V) (Note) haracteristics Symbol Test ondition Min Typ. Max Unit D supply voltage 3 18 V Input voltage /V OUT V Note: The recommended operating conditions are required to ensure the normal operation of the device. Unused inputs must be tied to either V or GND. 2 26-6-1
T466BP/BF/BFN/BFT Static Electrical haracteristics (in case not specifically appointed, = V) haracteristics ontrol input high voltage ontrol input low voltage On-state resistance On-state resistance (between any 2 switches) Input/output leakage current Quiescent supply current Input current H level L level Symbol V IH I IS < 1 µa V IL I IS < 1 µa R ON R ON I OFF I DD Test ondition 4 2 8 V IS VDD V IN = 18 V, V OUT = V V IN = V, V OUT = 18 V V IN =, (Note) (V) 1 1 1 1 1 1 1 1 18 18 1 1 Min Max Min Typ. Max Min Max 3. 7. 11. 1. 3. 4. 8 21 14 ±1 ±1.2. 1. 3. 7. 11. 2.7. 8.2 2.2 4. 6.7 29 12 8 1 6 4 ±.1 ±.1.1.1.2 1. 3. 4. 9 2 16 ±1 ±1.2. 1. 3. 7. 11. 1. 3. 4. 12 3 2 ±1 ±1 I IH V IH = 18 V 18.1 1.1 1. 7. 1. 3. I IL V IL = V 18.1 1.1 1. Unit V V Ω Ω na µa µa Note: All valid input combinations. 3 26-6-1
Dynamic Electrical haracteristics (Ta = 2, = V, L = pf) haracteristics Phase difference between input to output Propagation delay time (control-out) Propagation delay time (control -OUT) Max control input repetition rate 3dB cutoff frequency Total harmonic distortion db feed through frequency Symbol φ I-O t pzl t pzh t plz t phz f max () f max (I-O) L = pf L = pf L = pf L = pf Test ondition L = 1 pf (Note 1) f = 1 khz (Note 2) (V) T466BP/BF/BFN/BFT (V) 1 1 1 1 1 1 1 1 Min Typ. Max Unit 1 8 2 2 4 3 2 1 12 12 4 2 1 12 4 3 8 7 6 ns ns ns MHz 3 MHz.3 % (Note 3) 6 khz db crosstalk frequency (Note 4) 1 MHz rosstalk (control-out) Input capacitance IN R IN = 1 kω R OUT = 1 kω L = 1 pf 1 1 2 4 6 ontrol input 7. Switch 1 Feed through capacitance IN-OUT. pf mv pf Note 1: Sine wave of ±2. p-p shall be used for V is and the frequency of 2 log 1 Note 2: V is shall be sine wave of ±2. V p-p VOS Vis = 3dB shall be f max. Note 3: Sine wave of ±2. V p-p shall be used for V is and the frequency of 2 log 1 feed-through. Note 4: Sine wave of ±2. V p-p shall be used for V is and the frequency of 2 log 1 crosstalk. VOUT Vis VOUT Vis = db shall be = db shall be 4 26-6-1
T466BP/BF/BFN/BFT ircuit for Measurement of Electrical haracteristics 1. φ I-O - WAVEFORM t r = 2 ns t f = 2 ns P.G. 9% % 1% 9% % 1% L = pf φ I-O φ I-O % % V OH V OL 2. t pzh, t phl, t plz, t phz (ONTROL-OUT) WAVEFORM tr = 2 ns tf = 2 ns P.G. SW 1 L = pf SW 2 ontrol 1% SW 1 = SW 2 = t pzh SW 1 = SW 2 = t pzl 9% % % % 9% % 1% 9% t phz 1% t plz V OH V OL V OH V OL 3. RON V IN V OUT (V V ) R = 1 IN OUT ON k VOUT [ Ω] 4. fmax () t r = 2 ns t f = 2 ns ontrol 9% % 1% 9% 1% % P.G. L = pf 1 f 2 26-6-1
T466BP/BF/BFN/BFT. rosstalk between Any Two Switches SWITH ON P.G. 2. V SWITH OFF V 2. V V OUT 6. rosstalk, ontrol to Input t r = 2 ns t f = 2 ns V OUT ontrol IN 9% 1% 9% 1% P.G. L = 1 pf V OUT 7. Total Harmonic Distortion, fmax (I-O), Feedthrough 2. V P.G. V OUT IN V L R L 1 f 2. V 6 26-6-1
T466BP/BF/BFN/BFT Package Dimensions Weight:.96 g (typ.) 7 26-6-1
T466BP/BF/BFN/BFT Package Dimensions Weight:.18 g (typ.) 8 26-6-1
T466BP/BF/BFN/BFT Package Dimensions Weight:.18 g (typ.) 9 26-6-1
T466BP/BF/BFN/BFT Package Dimensions (Note) Note: This package is not available in Japan. Weight:.12 g (typ.) 1 26-6-1
T466BP/BF/BFN/BFT Package Dimensions Weight:.6 g (typ.) 11 26-6-1
T466BP/BF/BFN/BFT Note: Lead (Pb)-Free Packages DIP14-P-3-2.4 SOP14-P-3-1.27A SOL14-P-1-1.27 TSSOP14-P-44-.6A RESTRITIONS ON PRODUT USE 6116EBA The information contained herein is subject to change without notice. 2123_D TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc. 2123_A The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ( Unintended Usage ). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer s own risk. 2123_B The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 616_Q The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 2123_ The products described in this document are subject to the foreign exchange and foreign trade laws. 2123_E 12 26-6-1