Available online at Energy Procedia 00 (2009) Energy Procedia 2 (2010) E-MRS Spring meeting 2009, Symposium B

Similar documents
Semiconductor Junctions

OPTIMIZATION OF COPPER INDIUM GALLIUM Di-SELENIDE (CIGS) BASED SOLAR CELLS BY BACK GRADING

Explanation of Light/Dark Superposition Failure in CIGS Solar Cells

Novel High-Efficiency Crystalline-Si-Based Compound. Heterojunction Solar Cells: HCT (Heterojunction with Compound. Thin-layer)

DEVICE CHARACTERIZATION OF (AgCu)(InGa)Se 2 SOLAR CELLS

1 Name: Student number: DEPARTMENT OF PHYSICS AND PHYSICAL OCEANOGRAPHY MEMORIAL UNIVERSITY OF NEWFOUNDLAND. Fall :00-11:00

Lecture 15: Optoelectronic devices: Introduction

Lecture 15 - The pn Junction Diode (I) I-V Characteristics. November 1, 2005

Semiconductor Physics and Devices

Conduction-Band-Offset Rule Governing J-V Distortion in CdS/CI(G)S Solar Cells

PHOTOVOLTAICS Fundamentals

ET3034TUx Utilization of band gap energy

Modelling thin film solar cells with graded band gap

Electrons are shared in covalent bonds between atoms of Si. A bound electron has the lowest energy state.

Metal Semiconductor Contacts

Lecture 5 Junction characterisation

EE 5611 Introduction to Microelectronic Technologies Fall Tuesday, September 23, 2014 Lecture 07

FYS 3028/8028 Solar Energy and Energy Storage. Calculator with empty memory Language dictionaries

Chapter 7. The pn Junction

3.1 Introduction to Semiconductors. Y. Baghzouz ECE Department UNLV

This is the 15th lecture of this course in which we begin a new topic, Excess Carriers. This topic will be covered in two lectures.

Solar cells operation

( )! N D ( x) ) and equilibrium

Thermionic Current Modeling and Equivalent Circuit of a III-V MQW P-I-N Photovoltaic Heterostructure

n N D n p = n i p N A

Quiz #1 Practice Problem Set

Review Energy Bands Carrier Density & Mobility Carrier Transport Generation and Recombination

MODELING THE FUNDAMENTAL LIMIT ON CONVERSION EFFICIENCY OF QD SOLAR CELLS

Analyze the effect of window layer (AlAs) for increasing the efficiency of GaAs based solar cell

6.012 Electronic Devices and Circuits

Nanomaterials for Photovoltaics (v11) 14. Intermediate-Band Solar Cells

Comparison of Ge, InGaAs p-n junction solar cell

Chapter 7. Solar Cell

Optimization of the Properties of the Back Surface Field of a Cu(In,Ga)Se 2 Thin Film Solar Cell

ECE-305: Spring 2018 Exam 2 Review

Impact of the Geometry Profil of the Bandgap of the CIGS Absorber Layer on the Electrical Performance of the Thin-film Photocell

Lab #5 Current/Voltage Curves, Efficiency Measurements and Quantum Efficiency

February 1, 2011 The University of Toledo, Department of Physics and Astronomy SSARE, PVIC

Organic Electronic Devices

The Opto-Electronic Physics That Just Broke the Efficiency Record in Solar Cells

Uncorrected Proof. Thin-film solar cells made with two different processes for the deposition of Cu(In1 xgax)se2 (CIGS) or

A. K. Das Department of Physics, P. K. College, Contai; Contai , India.

Lecture 20 - p-n Junction (cont.) October 21, Non-ideal and second-order effects

Semiconductor Devices and Circuits Fall Midterm Exam. Instructor: Dr. Dietmar Knipp, Professor of Electrical Engineering. Name: Mat. -Nr.

Introductory Nanotechnology ~ Basic Condensed Matter Physics ~

Available online at ScienceDirect. Energy Procedia 55 (2014 ) 30 37

PHYSICAL ELECTRONICS(ECE3540) CHAPTER 9 METAL SEMICONDUCTOR AND SEMICONDUCTOR HETERO-JUNCTIONS

Fundamentals of Semiconductor Physics

Influence of the doping of the absorber and the charged defects on the electrical performance of CIGS solar cells

Lecture 15 The pn Junction Diode (II)

Lecture 12. Semiconductor Detectors - Photodetectors

Lecture 16 The pn Junction Diode (III)

Solar Cell Physics: recombination and generation

Photovoltaic Energy Conversion. Frank Zimmermann

Available online at ScienceDirect. Energy Procedia 92 (2016 ) 24 28

3.1 Absorption and Transparency

Lecture 16 - The pn Junction Diode (II) Equivalent Circuit Model. April 8, 2003

pn JUNCTION THE SHOCKLEY MODEL

PHYSICAL ELECTRONICS(ECE3540) CHAPTER 9 METAL SEMICONDUCTOR AND SEMICONDUCTOR HETERO-JUNCTIONS

Characterization of deep defects in CdSyCdTe thin film solar cells using deep level transient spectroscopy

Fundamental Limitations of Solar Cells

Fundamentals of the Metal Oxide Semiconductor Field-Effect Transistor

Semiconductor Physics fall 2012 problems

SEMICONDUCTOR HETEROJUNCTIONS

Schottky Diodes (M-S Contacts)

KATIHAL FİZİĞİ MNT-510

e - Galvanic Cell 1. Voltage Sources 1.1 Polymer Electrolyte Membrane (PEM) Fuel Cell

Institute of Solid State Physics. Technische Universität Graz. Exam. Feb 2, 10:00-11:00 P2

Modeling Recombination in Solar Cells

ECE 606 Homework Week 7 Mark Lundstrom Purdue University (revised 2/25/13) e E i! E T

Computer modelling of Hg 1 x Cd x Te photodiode performance

Spring Semester 2012 Final Exam

Semiconductor Physics Problems 2015

Charge Extraction from Complex Morphologies in Bulk Heterojunctions. Michael L. Chabinyc Materials Department University of California, Santa Barbara

Chalcogenide semiconductor research and applications. Tutorial 2: Thin film characterization. Rafael Jaramillo Massachusetts Institute of Technology

Schottky Rectifiers Zheng Yang (ERF 3017,

Simulation of Quantum Dot p-i-n Junction Solar Cell using Modified Drift Diffusion Model

ECEN 3320 Semiconductor Devices Final exam - Sunday December 17, 2000

V BI. H. Föll: kiel.de/matwis/amat/semi_en/kap_2/backbone/r2_2_4.html. different electrochemical potentials (i.e.

CHAPTER 4: P-N P N JUNCTION Part 2. M.N.A. Halif & S.N. Sabki

Current mechanisms Exam January 27, 2012

Photovoltaic cell and module physics and technology

Semiconductor Physics fall 2012 problems

Lecture 2. Introduction to semiconductors Structures and characteristics in semiconductors

Semiconductor device structures are traditionally divided into homojunction devices

Defects and diffusion in metal oxides: Challenges for first-principles modelling

Sheng S. Li. Semiconductor Physical Electronics. Second Edition. With 230 Figures. 4) Springer

Thesis. Numerical Modeling of CIGS Solar Cells: Definition of the Baseline and. Explanation of Superposition Failure. Submitted by.

SEMICONDUCTOR PHYSICS REVIEW BONDS,

STUDY OF THE PERFORMANCES OF A TANDEM PHOTOVOLTAIC CELL BASED ON CIGS

Classification of Solids

junctions produce nonlinear current voltage characteristics which can be exploited

Supplementary Figure 1. Supplementary Figure 1 Characterization of another locally gated PN junction based on boron

Towards a deeper understanding of polymer solar cells

Organic Electronic Devices

LEC E T C U T R U E R E 17 -Photodetectors

Basic Physics of Semiconductors

Semiconductor. Byungwoo Park. Department of Materials Science and Engineering Seoul National University.

Chemistry Instrumental Analysis Lecture 8. Chem 4631

Appendix 1: List of symbols

Transcription:

Available online at www.sciencedirect.com Energy Procedia 00 (2009) 000 000 Energy Procedia 2 (2010) 169 176 Energy Procedia www.elsevier.com/locate/procedia www.elsevier.com/locate/procedia E-MRS Spring meeting 2009, Symposium B A Simple Model of Graded Band-Gap CuInGaSe 2 Solar Cells Arturo Morales-Acevedo* Centro de Investigación y de Estudios Avanzados del IPN Electrical Engineering Department Avenida IPN No. 2508 07360 México, D. F. Abstract he effects of quasi-electric fields, caused by the band-gap variation of the active semiconductor, upon the illumination current density and open-circuit voltage of a solar cell will be discussed. In addition, it will be shown that open-circuit voltage improvement is possible when the band-gap is gradually increased within the space charge region from the neutral to the hetero-junction interface so that the dark saturation current density of the cell is reduced. Our estimation is that in the case of a solar cell where the band-gap increases from 1.15 ev to 1.4 ev, at the space charge region (of the order of 0.2 m), an increase of the open-circuit voltage around 80 mv will be observed with respect to the single gap absorbing material case. A similar (increasing) band-gap variation within the bulk of the material will cause an increase of the drift-diffusion length of minority carriers by a factor of 5 with respect to a single band-gap material. hen, based on these physical concepts, two possible structures with variable band-gap CIGS layers are proposed in order to have higher efficiencies than cells without any band-gap grading. It will also be shown that very likely present record efficiency CIGS solar cells have achieved efficiencies as high as = 19.9% due to (intentional or non-intentional) band-gap grading of the CIGS layer. his band-gap grading can be optimized with the purpose of a further efficiency increase. 2009 Published Received by Elsevier 1 JuneB.V. 2009; received in revised form 1 December 2009; accepted 20 December 2009 73.40.Lq; c 2010 73.50.Pz; Published 73.61.Le by Elsevier Ltd Open access under CC BY-NC-ND license. CIGS, Solar Cells, Band-gap grading 1. Introduction Increasing the open-circuit voltage (Voc) to improve the efficiency of Cu(In 1-x Ga x )Se 2 (CIGS) cells is highly desirable. When alloying CuInSe 2 (CIS) with Ga to form CIGS thin films, the wider band-gap energy of the CIGS absorber layer can potentially increase the Voc of the fabricated cells, at the expense of a reduction in the value of the short-circuit current density (Jsc). Introducing a spatial variation of the Ga content within the CIGS layer, the band-gap profile can be optimized to increase both the photon absorption and carrier collection. Furthermore, the Ga profile can be adjusted to optimize the CIGS absorber band-gap profile, and hence improve the Voc and Jsc values. *el.: +525557473781 e-mail: amorales@solar.cinvestav.mx. 1876-6102 c 2010 Published by Elsevier Ltd doi:10.1016/j.egypro.2010.07.024 Open access under CC BY-NC-ND license.

170 A. Morales-Acevedo / Energy Procedia 2 (2010) 169 176 Author name / Energy Procedia 00 (2010) 000 000 hus, band-gap engineering geared to controlling the spatial distribution of the Ga content in the absorber layer can lead to enhancing the overall performance of CIGS cells. However, a clear understanding of the fundamental device physics of these structures is necessary to exploit the benefits of a design strategy and for its optimization. he merits of numerical modeling are that spatially varying parameters can be analyzed throughout the device and new design concepts can be tested without actual fabrication. Several investigations have been made in this regard [1-6], but usually the final results hinder to some extent the basic device physics associated to a given result. Here, we propose that it is better to have first a clear understanding of the physics of a cell device so that an optimal structure is analyzed, and then a refined numerical model can be used to have a more exact prediction of the cell behavior. Sophisticated numerical models should be used as a way of understanding effects which usually are difficult to deal with simple physical models. For example, solar cells under concentrated sunlight require a bidimensional numerical solution in order to take into account the bi-dimensional current flows or the high injection levels associated to the carrier transport and recombination in the structure. Numerical solutions are also required to take into account the doping variation as a function of depth (in the emitter) of solar cells. However, most of the physics of conventional solar cells is contained in the Shockley diode model, allowing simple calculations to be used to predict the electrical characteristics of such devices. herefore, in this paper we try to establish a conceptual basis for solar cells made with varying gap semiconductor materials, in the same manner as the Shockley diode equation is a first order approximation for the conventional solar cells behavior. First order approximations are made here, in a similar way to the Shockley model for a solar cell, so that higher order approximations can be taken into account as a refinement of the model. It will be shown that the expected results associated to band-gap grading according to our model are similar to those obtained with numerical models such as published recently by Gloeckler and Sites [1], confirming that most of the physics of solar cells based on variable band-gap materials can be dealt with a simple model. In what follows, first some basic concepts that are relevant for designing highly efficient solar cells, where the band-gap energy of the CIGS absorber layer is not uniform, are discussed. hen, based on these concepts, CIGS band-gap profiles are proposed in order to attain solar cells with high efficiencies. Finally, a calculation will be made in order to determine the expected efficiency increase for present CuInGaSe 2 solar cells, by assuming that this kind of solar cells still does not have a band-gap profile as suggested here for improving the cell performance. 2. Basic Concepts for Solar Cells with varying band-gap absorber layers 2.1 ypical CIGS solar cell structure he typical CIGS cell structure is depicted in fig. 1. Usually, the buffer layer in contact with the absorber layer is a CdS thin film. Other materials have been tried as buffer layers in order to avoid the presence of atomic Cd, as part of the solar cells. However, the best results have been obtained with CdS and hence this material continues to be the preferred one. he absorption in the buffer and the conducting oxide (CO) layers should be negligible, so that much of the incident photons are absorbed by the CIGS active layer for generating the photo-current. hen, very thin (30-80 nm) CdS films and very transparent CO materials are used in order to achieve high efficiencies. he contact at the back is Mo. All of these conditions have been achieved already and are not limiting factors in present technology solar cells. herefore, the most important layer remaining for optimization is the CIGS one, and this will be the topic of discussion here. It will be assumed that Ga concentration can be varied in order to achieve appropriate band-gap profiles, as proposed in the following sections. 2.2. Absorption in variable band-gap materials CuInSe 2 and CuInGaSe 2 are materials with direct band-gap absorption characterized by an absorption coefficient of the form =0 1 h < E g A h E ) 2 E g < h (1) ( g

A. Morales-Acevedo / Energy Procedia 2 (2010) 169 176 171 Author name / Energy Procedia 00 (2010) 000 000 where E g is the band-gap of the material, h is the photon energy of the incident radiation and A is a constant which depends upon the effective masses of electrons and holes in the conduction and valence bands, respectively. Figure 1. Schematics of a typical solar cell structure based on p-cuingase 2. he common transparent conducting oxide (CO) is ZnO, the buffer layer is CdS, and the back contact is Mo. he thickness of the layers may vary according to the technology used for deposition. In a recent study, the author [7] has shown that absorption in a direct band semiconductor where the bandgap varies as a function of position (see fig. 2), the absorption rate can be calculated in a similar manner as for single band-gap materials with an effective absorption coefficient eff, of the form: eff = 0 2 h Eg min eff = g min( ) 3 E E eff = gmin g max g min 0 h E g min E 3 Eg min (2) 2 g min h ( Eg max Eg min ) 3 ( Eg max Eg min) Eg 2 min h where gmin is the absorption coefficient given by eq. (1) for E g = E gmin. he maximum and minimum band-gaps E gmax and E gmin are described in figure 2 for a material with linear band-gap variation. It must be noticed that the latter expression is valid for light incident from any side of the variable gap material. It was also shown that the expected reduction of photocurrent for a material with a given total band-gap variation E g = E gmax - E gmin is much less than the photocurrent loss due to a material with the corresponding average band-gap, when compared with the expected photocurrent for a material with the minimum band-gap E gmin. In other words, grading the band-gap does not cause much variation of the photon absorption, but it may induce an internal electric field which may help improving the open circuit voltage and the collection of photo-generated carriers, as will be shown in the following sections. herefore, from the above considerations, instead of looking for an optimum single band-gap material we can now look for an optimal band-gap grading so that the expected efficiency will be even greater than for an absorber material with an optimum single gap. However, the graded regions within the structure of a solar cell have to be placed in the appropriate position in order to achieve the proposed improvement, as will be discussed below.

172 A. Morales-Acevedo / Energy Procedia 2 (2010) 169 176 Author name / Energy Procedia 00 (2010) 000 000 Figure 2. Band structure for a material with linear band-gap variation as a function of depth position (total thickness d). For simplicity, we have assumed that the gap variation is due to the conduction band variation. 2.3 Internal electric field associated to band-gap grading In fig. 2, it can be seen that due to the conduction band-variation with position, electrons will feel a force similar to the drift force due to an electric field. he electron current density, taking into account, the electric potential variation, the carrier diffusion and the electron affinity variation, will be: J n 1 d( V e) q q nn qd dx n dn dx (3) where n(x) is the electron concentration at any position x in the conduction band, n is the electron mobility, D n is the electron diffusion coefficient, V is the electric potential, e is the electron affinity and q is the magnitude of the electron s charge. V + e /q is the total electrochemical potential in the semiconductor. hen, electrons are drifted by means of the total electric field: 1 d( V e) q dv e dx dx 1 d e dv q dx dx 1 de q dx C (4) where E C (x) is the conduction band energy at position x. A similar expression can be written for holes in the valence band, but for simplicity, we shall discuss only the case of electrons in the conduction band since we shall assume that minority carriers in the absorbing semiconductor are electrons, as is the case for CIGS solar cells. According to eq. (4), electrons will be drifted by the electric field due to the potential variation and by the additional quasi-electric field associated to the affinity (conduction band) variation with position. his field will reduce both the back surface recombination at the ohmic contact and the bulk recombination typically characterized by the diffusion length. In the case of a graded band-gap material it is more appropriate to define a drift-diffusion length. If the electron drift and diffusion current components are in the same direction, the drift-diffusion length will be [8]: L l n n (5) ln 2 ln 1 ( )

A. Morales-Acevedo / Energy Procedia 2 (2010) 169 176 173 Author name / Energy Procedia 00 (2010) 000 000 l n is the electron diffusion length, V is the thermal potential (k/q) and is the quasi-electric field in the respective region. As an example, let us consider a 2 m linearly graded CIGS layer, which is typical in present solar cells, with an electron diffusion length of the order of 1 m, and in which the total band-gap change is E C = 0.25 ev. In this case, the quasi-electric field will be around 1.25 x 10 3 V/cm and the drift-diffusion length will become more than 5 times the diffusion length, i. e. 5 m. Of course, this higher drift-diffusion length would increase the electron collection at the hetero-junction if the quasi-electric field is such that carriers are drifted towards it. Another effect due to this quasi-electric field would be to reduce the recombination at the back contact. In summary, the quasi-electric field associated to a varying band-gap material in a solar cell structure should cause both reduced bulk and surface recombination, if the field is in the appropriate direction. In the case of a p-type CIGS layer, the needed quasi-electric field should be directed towards the back contact so that electrons are drifted in the opposite direction. In other words, in this case, the band-gap must increase towards the back contact. 2.4 Effect of band-gap variation upon the dark current in a solar cell Current transport in hetero-junction solar cells under dark conditions occurs as a consequence of different mechanisms. Ideally, the dominant current transport mechanism is carrier injection at the junction and diffusion due to a carrier gradient caused by recombination at the bulk and surface of the respective material at each side of the junction. However, in real non-ideal junctions other mechanisms are present, such as recombination caused by traps at the junction interface enhanced by tunneling, or due to Shockley-Read-Hall recombination at deep levels within the space charge region of the junction. he latter mechanism will be assumed for CIGS solar cells, but the analysis below can also be applied for ideal solar cells where the current is dominated by diffusion carrier transport (ideality factor n=1). For a (hetero) junction dominated by deep level recombination at the space charge region, the dark current density can be approximated (for V > ) by V J J0 exp( ) (6) where V is the applied potential and J0 qn i S scr (7) n i is the intrinsic carrier density and S scr is an effective recombination velocity at the space-charge region of the cell. It is related to the trap density and the carrier capture cross section for the trap levels there and is only slightly dependent (square root function) upon the operating voltage, particularly under forward bias. In this model, states distributed in the band-gap can be taken into account by means of an average effective trap level that takes into account all these traps. he important issue here is the dependence of J 0 on the intrinsic carrier concentration n i, which in turn has an exponential dependence upon the average band-gap within this region. From eq. (7), the reduction of the dark saturation current density, when a variable gap material is inserted within the space charge region, can be estimated. For doing this, let us consider the average of the intrinsic carrier concentration which will vary along this region since the band-gap will not be constant. herefore, in this case, it can be shown that the expected dark saturation current density will be: J 0 J 0 min V g ( )[1 exp( )] J0 min( ) V V g g (8)

174 A. Morales-Acevedo / Energy Procedia 2 (2010) 169 176 Author name / Energy Procedia 00 (2010) 000 000 with V g = E g /q, the total band potential change, and J 0min being the dark saturation current density for a material with the minimum band-gap E gmin. As an example, let us consider again a graded band-gap material in which V g = 0.25 V. In this case the dark saturation current density would be reduced by a factor of 5 approximately, and the open-circuit voltage would increase around 80 mv with respect to a solar cell in which a CIGS layer with a given (minimum) band-gap is used. hen, if a variable band-gap material is produced close to the hetero-junction in such a way that the gap is changed from E gmax to E gmin within the space charge region, the open circuit voltage should increase by about 80 mv when the total E g = E gmax - E gmin = 0.25 ev. Figure 3. CuInGaSe 2 absorber profile in a solar cell (a) with a uniform band-gap and optimum E g = 1.15 ev. (b) One of the possible non-uniform absorber profiles that will allow better performance than the case shown in (a) due to the quasi-electric field in the material bulk. he maximum band-gap at the back contact will have to be optimized in order to obtain an improved short circuit current density. (c) Another structure that will allow better performance than in case (a). he band-gap variation at the junction interface will cause better open-circuit voltage, and the band-gap variation at the back interface will cause reduced back recombination and better short circuit current density. In all cases, we are assuming that the junction interface is at the left side and the back contact interface is at the right side. In order to have the improvement discussed above without causing photo-current losses, two conditions are required. he first one is that the quasi-electric field produced by the band-gap variation in the space charge region should be smaller than the electric field caused by the electrical charge there, otherwise there would be no collection of photo-generated carriers at the junction since these fields are in opposite directions for a material with decreasing band-gap from the junction interface towards the quasi-neutral region. he space charge width for this kind of cell will be of the order of 0.2 m. herefore, it is advisable to have E g to be around 0.25 ev in this region. he quasielectric field caused by this band-gap variation would be around 1.25 x 10 4 V/cm directed to the junction interface. In addition, a second condition is that the region for band-gap variation should not extend beyond the space charge region since this quasi-electric field would oppose the motion of photo-generated carriers from the bulk of the semiconductor towards the collecting junction. From all of the above considerations and analysis it is possible to make a proposal for higher efficiency CuInGaSe 2 solar cell structures, as will be discussed below. 3. Device structures for Improved Solar Cells with graded band-gap layers he basic structure for a CIGS solar cell has been depicted in fig. 1. he CIGS absorber layer has the band-gap profile described in fig. 3 (a). In other words, the band-gap is uniform along the whole thickness of this layer. It has been established that an optimum band-gap value is around 1.15 ev. wo possible device structures can be proposed

A. Morales-Acevedo / Energy Procedia 2 (2010) 169 176 175 Author name / Energy Procedia 00 (2010) 000 000 in order to have improved solar cells. he CIGS layers band-gap profiles are shown in fig. 3(b) and fig. 3 (c). In the first one, a decreasing band-gap region within the space charge is inserted in such a way that the open-circuit voltage can be increased. hen, a second CIGS layer is graded with an increasing band-gap towards the contact, so that the electron collection at the junction is improved due to the reduced bulk and surface recombination, as explained in section 2. Notice, however, that the band-gap grading will cause only slight reduced photon absorption; as calculated by the author in a preceding paper [7]. herefore, E g for this region should be optimized for a given CIGS film thickness and diffusion length so that there is a real increase of the photo-current with respect to the one obtained with the non-graded material. his kind of absorber profile has already been studied experimentally [9] and some of the effects described above have been confirmed, but the band-gap grading in each region have not been optimized. he discussion above would allow for a better understanding on how to optimize this kind of solar cell structure and band-gap profile. Another band-gap profile for the CIGS layer in a solar cell structure is proposed in fig. 3 (c). In this structure, in the region close to the junction, the band-gap E g will have a total reduction of 0.25 ev within the space charge region, causing the increase on the open-circuit voltage as explained above. hen, a second layer will have a constant band-gap which will be the optimum for single gap CIGS solar cells, i.e. 1.15 ev. hen, close to the CIGS- Mo contact, a third region with increasing band-gap and total E g > 0.25 ev in a small distance of 0.1 m will cause a quasi-electric back surface field that will reduce the surface recombination at the contact. In this case, notice that back surface recombination velocities as high as 1 x 10 6 cm/s could be compensated by the back surface quasielectric field, if the above grading occurs in only 0.1 m, and the electron mobility is around 40 cm 2 /Vs. Using the above arguments, it can be established that any of the structures shown in figures 3 (b) and 3 (c) will have an improved efficiency with respect to solar cells without any intentional band-gap grading. 4. Improving the performance of present high efficiency CuInGaSe 2 solar cells Recent record efficiencies for CIGS solar cells have been reported around 19.5% - 19.9% [10]. Unfortunately, not many details are given about the steps for making these record solar cells nor a full characterization is given either, so that we do not know if there is a band-gap grading such as the suggested variation discussed above in the real structures. However, numerical results for solar cells with a constant band-gap CIGS layer do not give results providing such high efficiencies [5, 6] in the best of the cases. herefore, we may suspect that the high efficiencies observed experimentally are due to the inclusion of a graded band-gap CIGS layer, according to our previous discussion. It must be noticed that the above effects have already been observed experimentally by Dullweber et al. [9]. In addition, numerical results [5] have also shown that high efficiency CIGS solar cells can be achieved whenever the band-gap grading profiles analyzed in this paper are achieved for the CIGS layer. he main advantage of our approach is that we now have a simple analytical model for this kind of solar cells. Furthermore, using simple expressions for the carrier collection probability and for the ideal dark saturation current density it will be possible to establish an analytical tool for optimizing both the front and back band-gap grading suggested in figures 3 (b) and 3(c). 5. Conclusions In this paper, some basic concepts related to the application of variable band-gap absorbing semiconductors in solar cells have been discussed. For example, the effects due to the associated quasi-electric field on the drift-diffusion length and the back surface recombination velocity will cause a larger carrier collection with a likely increase of the illumination current density. It was also shown that for an additional improvement of the open-circuit voltage, a band-gap reduction is needed within the space charge region so that the dark saturation current density reduces, assuming that deep level recombination dominates the dark current. Our estimation is that in the case of a solar cell where the band-gap reduces from 1.4 ev to 1.15 ev, at the space charge region (of the order of 0.2 m), an increase of the open-circuit voltage of about 80 mv will be achieved with respect to the case of solar cells where the CIGS layer has a uniform band-gap of 1.15 ev. hese effects have been confirmed experimentally by Dullweber et al., and possibly the present record efficiency CIGS solar cells have been achieved with such band-gap grading, but the above model and concepts show that there might be still some possibility for further cell optimization by engineering the band-gap profile in the CIGS base of the solar cell.

176 A. Morales-Acevedo / Energy Procedia 2 (2010) 169 176 Author name / Energy Procedia 00 (2010) 000 000 Acknowledgements. his work has been partially supported by Consejo Nacional de Ciencia y ecnología of México through project CB-2007-01 No. 083042. REFERENCES 1. M. Gloeckler and J. R. Sites, J. Phys. Chem. Solids 66 (2005), 1891-1894. 2. G. Sassi, heoretical analysis of solar cells based on graded band-gap structures, J. Appl. Phys. 54 (1983), 5421-5427. 3. A. Dhingra, A. Rothwarf, Computer simulation and modeling of graded bandgap CuInSe 2 /CdS based solar cells, IEEE rans. Electron Devices 43 (1996) 613-621. 4. M. opic, F. Smole, J. Furlan, Band-gap engineering in CdS/Cu(In,Ga)Se 2 solar cells, J. Appl. Phys. 79 (1996) 8537-8540. 5. J. Song, S. S. Li, C. H. Huang, O. D. Crisalle and. J. Anderson, Device modeling and simulation of the performance of Cu(In 1 x,ga x )Se 2 solar cells, Solid-State Electronics 48 (2004) 73-79. 6. S. Al. Alagappan and S. Mitra, Optimizing the design of CIGS-based solar cells: a computational approach, Materials Science and Engineering B 116 (2005) 293 296. 7. A. Morales-Acevedo, Effective absorption coefficient for graded band-gap semiconductors and the expected photo-current density in solar cells, Solar Energy Mater. & Solar Cells 93 (2009), 41-44. 8. H. J. Hovel, Semiconductors and Semimetals, Edited by R. K. Willardson and A. C. Beer, (Academic, New York, 1975), Vol. 11. 9.. Dullweber, G. Hanna, U. Rau, H.W. Schock, A new approach to high-efficiency solar cells by band gap grading in Cu(In,Ga)Se 2 chalcopyrite semiconductors, Solar Energy Mater. & Solar Cells 67 (2001) 145-150. 10. I. Repins, M. A. Contreras, B. Egaas, C. DeHart, J. Scharf, C. L. Perkins, B. o and R. Noufi, 19.9%-efficient ZnO/CdS/CuInGaSe 2 Solar Cell with 81.2% Fill Factor, Prog. Photovolt: Res. Appl. 16 (2008), 235 239.