10 Schlüter -BEKOTEC-EN is a studded screed panel made of polystyrene, which is designed for the attachment of the Schlüter -BEKOTEC-THERM-HR heating pipes, with a diameter of 16 mm. The panels are grooved for optimal joining. The heating pipes are attached in the desired spacing between the cutback studs, which are arranged in a regular spacing pattern of 75 mm. Conventional screed CT-C25-F4 (ZE 20) or CA-C25-F4 (AE 20) is installed above the studs with a thickness of at least 8 mm and at most 25 mm. Schlüter -BEKOTEC-EN/ consists of polystyrene (ES 033 DEO), white, without foil coating, and is most suited for conventional cement screeds. Schlüter -BEKOTEC-EN/F consists of polystyrene (ES 033 DEO), with foil coating (orange), and is especially suited for flowing screeds (e.g. gypsum based screeds). Technical Data: Installation width: 75-150-225-300 mm Schlüter -BEKOTEC-EN Material classification: B2 pursuant to DIN 4102 Heat conductor group: 033 (0.033 W/mK) U value: 1.650 W/m 2 K Thermal resistivity: 0.606 m 2 K/W for the installation of ceramic tile or natural stone on top of the Schlüter -BEKOTEC screed, it is first necessary to adhere the Schlüter -DITRA uncoupling mat to the screed. This installation can take place as soon as the screed is able to bear weight (gypsum based screeds: < 2% residual moisture). lease refer to our product data sheets 6.1 and 9.1 Schlüter -BEKOTEC-ENR Schlüter -BEKOTEC-ENR is an edge panel made of polystyrene (ES 040 DEO) for optimising cuts of Schlüter -BEKOTEC studded panels EN/ and EN/F, adding small areas or filling small spaces between walls and upright structural elements. Schlüter -BEKOTEC-EN/ EN/ screed panel without foil coating 75.5 x 106 cm = 0.8 m 2 / m 2 EN 2520 10.17 20 EN/ screed panel without foil, e.g. conventional cementitious screeds. 1 panel (0.8 m 2 ) = smallest delivery unit Schlüter -BEKOTEC-EN/F EN/F = screed panel with foil coating 75.5 x 106 cm = 0.8 m 2 / m 2 EN 1520 F 12.22 20 EN/F = screed panel with foil for flowing screeds, e.g. gypsum based screeds. 1 panel (0.8 m 2 ) = smallest delivery unit Schlüter -BEKOTEC-ENR ENR = edge panel 30.5 x 45.5 cm = 0.14 m 2 ENR 1520 1.19 20 box packaging.
Schlüter -BEKOTEC-EN 23 F Schlüter -BEKOTEC-EN 23 F Schlüter -BEKOTEC-EN 23 F is a studded screed panel made of high impact polystyrene, designed for the EN 23 F = studded screed panel of attachment of the heating pipes Schlüter -BEKOTEChigh impact polystyrene THERM-HR 14 mm. The Schlüter -BEKOTEC panels Useable area 120 x 90 cm / m are connected by overlapping a row of studs and clicking the panels together. The cutback studs hold the EN 23 F 9.56 20 2 heating pipes in a precise 75 mm pattern, depending on the required pipe spacing. The screed is professionally installed as conventional screed of quality CT-C25-F4 The uncoupling mat Schlüter -DITRA (ZE20) or CA-C25-F4 (AE 20), with a coverage of at least must be adhered to the screed prior to the 8 mm and no more than 25 mm above the studs. installation of ceramic tiles or natural stone over the Schlüter -BEKOTEC screed. The mat can Technical data: be installed as soon as the screed is sufficiently Installation spacing: 75-150 - 225-300 mm ready to bear weight (gypsum screeds: < 2% Construction material class: B2 acc. to DIN 4102 residual moisture). lease observe the instructions of our product data sheets 6.1 and 9.2. Schlüter -BEKOTEC-ENFG The leveling panel Schlüter -BEKOTEC-ENFG is installed in the area of door openings and heating circuit distributors to simplify connections and to minimise cutting waste. It consists of polystyrene foil material and is adhered below the studded panels EN 23 F, using the double-sided adhesive tape. Schlüter -BEKOTEC-BTZRKL Schlüter -BEKOTEC-BTZRKL is a pipe clamping strip for securing the pipes on the levelling panel ENFG. The clamping strips are self-adhesive to allow for permanent attachment. Schlüter -BEKOTEC-BTZDK Schlüter -BEKOTEC-BTZDK66 is a double-sided adhesive tape for adhering the studded panel EN 23 F to the substrate. Schlüter -BEKOTEC-ENFG ENFG = levelling panel 127.5 x 97.5 cm, thickness: 1.2 mm set ENFG 14.76 10 Schlüter -BEKOTEC-BTZRKL BTZRKL = pipe clamping strip Length: 20 cm, Number of pipe spaces: 4 per unit / BTZRKL 3.20 10 Schlüter -BEKOTEC-BTZDK66 BTZDK = double-sided adhesive tape Roll: 66 m, height: 30 mm, thickness: 1 mm / BTZDK66 42.45 10 box packaging. 11
Schlüter -BEKOTEC-BTS Schlüter -BEKOTEC-BTS is a 5 mm thick insulation layer of closed cell polyethylene foam for installation below the Schlüter studded screed panels. The use of Schlüter -BEKOTEC-BTS results in a significant improvement of sound insulation. The material can be used if the required construction height is not sufficient for a thick insulation layer of polystyrene or mineral fibre. The maximum floor load must be limited to 2 kn/m 2. Schlüter -BEKOTEC-BTS BTS = impact sound insulation 5 mm x 1 m x 50 m (50m 2 ) 1 roll (50 m 2 ) = delivery unit / m 2 rolls BTS 510 2.96 5 Schlüter -BEKOTEC-BRS Schlüter -BEKOTEC-BRS is an edging strip of closed cell polyethylene foam with an integrated foil leg. The edging strip is installed along walls or fixed room components. The foil leg is installed beneath the Schlüter -BEKOTEC panels or the E foil cover and is suitable for conventional cement screeds. The finishing strip Schlüter -BEKOTEC-BRSK is equipped with an additional adhesive strip for attachment to the wall. Schlüter -BEKOTEC-BRS BRS 810 = edging strip BRSK 810 = edging strip self adhesive 8 x 100 mm x 50 m 1 roll (50 m) = delivery unit / m rolls BRS 810 0.60 10 BRSK 810 0.78 10 Schlüter -BEKOTEC-BRS/KF Schlüter -BEKOTEC-BRS/KF is an edge strip of closed cell polyethylene foam with an adhesive leg and an adhesive backing for wall attachment. When the Schlüter -BEKOTEC studded panel is laid on the E adhesive, the resulting connection prevents flowing screeds from running underneath the assembly during installation. Schlüter -BEKOTEC-BRS/KF BRS/KF = edging strip with adhesive leg 8 x 80 mm x 25 m 1 roll (25 m) = delivery unit / m rolls BRS 808 KF 1.27 10 Schlüter -BEKOTEC-BRS/KSF Schlüter -BEKOTEC-BRS/KSF is an edging strip of closed cell polyethylene foam with an integrated foil leg that features an adhesive strip on both sides for attachment. The edging strip is pressed toward the wall by the adhesion on the substrate and the pre-tensioning of the integrated foil leg. When the studded panel Schlüter - BEKOTEC is laid on top of the adhesive strip, flowing screed can no longer flow underneath the panel. Schlüter -BEKOTEC-BRS/KSF BRS/KSF = edging strip for flowing screeds with integrated foil leg 8 x 80 mm x 25 m 1 roll (25 m) = delivery unit / m rolls BRS 808 KSF 1.71 5 BRS 808 KSF is especially suitable for combination with EN 23 F. 10 H Schlüter -DILEX-DF Schlüter -DILEX-DF is a movement profile for installation in door areas or for establishing fields in screed areas. Schlüter -DILEX-DF DF flexible movement joint H = mm L = 1.00 m 60 DF 6/100 7.19 20 80 DF 8/100 8.44 20 100 DF 10/100 9.84 20 L = 1.80 m 100 DF 10/180 17.10 20 12 box packaging.
16 x 2 mm 16 x 2 mm 14 x 2 mm Schlüter -BEKOTEC-THERM-HR Schlüter -BEKOTEC-THERM-HR is a heating pipe of high quality synthetic E-RT, highly flexible, for optimised attachment to the Schlüter -BEKOTEC studded screed panel. Diameter 14 mm or 16 mm, thickness of walls 2 mm, compliance with DIN 16833, impervious to oxygen according to DIN 4721/26, quality inspected by SKZ A240. Tested and certified in accordance with DIN-EN 1264 DIN CERTCO Reg. no. 3V270 E-RT Schlüter -BEKOTEC-THERM-HR HR = heating pipe 16 mm for EN/ and EN/F Length = m / m rolls 70 BTHR 16 RT 70 1.58 15 120 BTHR 16 RT 120 1.58 15 200 BTHR 16 RT 200 1.58 15 750 BTHR 16 RT 750 1.58 4 Schlüter -BEKOTEC-THERM-HR 14 x 2 mm 70 m in carton = shipping unit 120 m in carton = shipping unit 200 m in carton = shipping unit 750 m on disposable drum = shipping unit HR = heating pipe 14 mm for EN 23 F Length = m / m rolls 70 BTHR 14 RT 70 1.48 15 120 BTHR 14 RT 120 1.48 15 200 BTHR 14 RT 200 1.48 15 750 BTHR 14 RT 750 1.48 4 Schlüter -BEKOTEC-THERM-ZW Schlüter -BEKOTEC-THERM-ZW is an angle clip of synthetic material for defined 90 bends of the heating pipes Ø 14 or 16 mm in the distributor cabinet. The angle clip is easy to attach to the heating pipes from the side. Due to the relatively low thickness of the screed layer, the use of the clips is recommended. Schlüter -BEKOTEC-THERM-ZW ZW = angle clip BTZW 1418 1.53 50 2 required per heating circuit (hot and cold leg) Schlüter -BEKOTEC-THERM-HRA Schlüter -BEKOTEC-THERM-HRA is a dispensing unit that accommodates disposable drums with 750 m of Schlüter-heating pipe. It can be assembled without tools and is easily disassembled for transport. Made of a coated steel frame construction The unit consists of: - one 25 mm spindle - two triangular frames - two connecting brackets Schlüter -BEKOTEC-THERM-HRA HRA = heating pipe dispenser BTZHRA 750 190.97 Schlüter -BEKOTEC-THERM-RH Schlüter -BEKOTEC-THERM-RH 75 is an attachment clamp for the heating pipes, which can be anchored into the Schlüter -BEKOTEC studded panels across the studs. It is especially useful for forming 45 angles with 16 mm heating pipes in the studded panel. Schlüter -BEKOTEC-THERM-RH RH = heating pipe clamps for 16 mm heating pipes bag = 100. / bag bag BTZRH 75/100 18.22 10 BTZRH 17/100 9.55 10 Schlüter -BEKOTEC-THERM-RH 17 is a plastic clip with barbs for anchoring 16 mm heating pipes into the Schlüter -BEKOTEC studded panels. The heating pipe clips are not suitable for EN 23 F. box packaging. 13
Schlüter -BEKOTEC-THERM-HV/DE Schlüter -BEKOTEC-THERM-HV/A Number of heating circuits Schlüter -BEKOTEC-THERM-HV/DE Schlüter -BEKOTEC-THERM-HV/DE is a heating circuit distributor manifold DN 25 of stainless steel with hot leg and cold leg bars, outside diameter 35 mm. The following components are integrated and pre-installed into the set: - Hot leg flow meter with transparent scale, adjustable 0.5 to 5.0 l / minute for regulating flow quantities, - Thermostat valves, adjustable manually for every heating circuit, matching the electronically controlled Schlüter actuators, - Manual ventilation valve, nickel plated brass for hot and cold legs, - Filling and evacuation valve, 1/2" (DN 15), turning, nickel plated brass, - End plug 3/4" (DN 20), nickel plated brass, - Distributor connection, with 1 flat gasket male fitting (DN 25), - Heating circuit terminals, spaced 55 mm apart, consisting of connector nozzle 3/4" (DN 20) AG with cone, matching the Schlüter clamp connections, - 2 distributor manifold brackets with sound insulation inserts, matching the Schlüter distributor manifolds cabinet, as well as a wall mounting set are included loosely in the package for installation. Schlüter -BEKOTEC-THERM-HV/A Accessory sets for connecting the heating circuits to the heating circuit distributor, for heating pipes with Ø 14 or 16 mm, including 2 ball valves for the main connection. HV/DE = Heating circuit distributor HV/A = Distributor connection set Ø 16 mm HV/A = Distributor connection set Ø 14 mm / Set / Set / Set 2 BTHV 2 DE 113.14 BTHV 2 A 35.95 BTHV 2 A 14 34.87 5 3 BTHV 3 DE 146.02 BTHV 3 A 44.98 BTHV 3 A 14 43.36 5 4 BTHV 4 DE 178.93 BTHV 4 A 54.03 BTHV 4 A 14 51.85 5 5 BTHV 5 DE 211.79 BTHV 5 A 63.05 BTHV 5 A 14 60.33 5 6 BTHV 6 DE 244.69 BTHV 6 A 72.09 BTHV 6 A 14 68.82 5 7 BTHV 7 DE 277.56 BTHV 7 A 81.12 BTHV 7 A 14 77.32 5 8 BTHV 8 DE 310.44 BTHV 8 A 90.15 BTHV 8 A 14 85.81 5 9 BTHV 9 DE 343.35 BTHV 9 A 99.18 BTHV 9 A 14 94.30 5 10 BTHV 10 DE 376.24 BTHV 10 A 108.21 BTHV 10 A 14 102.79 5 11 BTHV 11 DE 409.11 BTHV 11 A 117.25 BTHV 11 A 14 111.27 5 12 BTHV 12 DE 441.97 BTHV 12 A 126.27 BTHV 12 A 14 119.77 5 Connection set components Ø 16 x 2 mm Example: BTHV 5 A for 5-component heating circuit distributor Ø 14 x 2 mm = Set Example: BTHV 7 A 14 for 7-component heating circuit distributor Ball valves R ¾ 2 per distributor 2 2 per distributor 2 Clamp connections 2 per heating circuit 10 2 per heating circuit 14 Angle clips 2 per heating circuit 10 2 per heating circuit 14 Heating pipe clamp RH 17 2 per heating circuit 10 Heating pipe clamp RH 75 2 per heating circuit 10 14 Schlüter -BEKOTEC-THERM-HVE Schlüter -BEKOTEC-THERM-HVE is a heating circuit distributor manifold expansion for the subsequent expan sion of the Schlüter heating circuit distributor of stainless steel. The following components are integrated and pre-installed into the set: - Hot leg flow meter with transparent scale, adjustable 0.5 to 5.0 l / minute for regulating flow quantities - Thermostat valve, adjustable manually for every heating circuit, matching the electronically controlled Schlüter actuators - Heating circuit terminal with connector nozzle 3/4" (DN 20) AG with cone, matching the Schlüter clamp connections. Schlüter -BEKOTEC-THERM-HVE HVE = HVE = heating circuit distributor expansion / Set = Set BTHVE 1 DE 66.95 5 The connection to the Schlüter -BEKOTEC- THERM heating pipes requires two clamp connections BTZ 2 KV and two angle clips BTZW 1418. box packaging.
Schlüter -BEKOTEC-THERM-KH Schlüter -BEKOTEC-THERM-KH is a ball valve, nickel plated brass, with 1" outside threading on one side (DN 25) for flat gasket connection to Schlüter heating circuit distributors and a connection pipe with 3/4" (DN 20) or 1" (DN 25) inside threading (shipping unit = set of two for hot leg and cold leg). Schlüter -BEKOTEC-THERM-KH KH = ball valve, 2 / set Ø set = 2 = set 3/4" BTZ2KH 20 17.88 10 1" BTZ2KH 25 26.01 10 Schlüter -BEKOTEC-THERM-KV Schlüter -BEKOTEC-THERM-KV is a 3/4" (DN 20) clamp connection made of nickel plated brass for connection of Schlüter heating pipes, diameter 14 mm or 16 mm, to the Schlüter heating circuit distributor (shipping unit = set with two for hot and cold leg). Schlüter -BEKOTEC-THERM-KV KV = clamp connection Ø mm set = 2 = set 16 BTZ2KV 16 5.43 10 14 BTZ2KV 14 5.43 10 Schlüter -BEKOTEC-THERM-KU Schlüter -BEKOTEC-THERM-KU is a 3/4" (DN 20) connection coupling made of nickel plated brass for the connection of Schlüter heating pipes, diameter 14 mm or 16 mm. Schlüter -BEKOTEC-THERM-AN Schlüter -BEKOTEC-THERM-AN is a 1/2" x 3/4" connector fitting made of nickel plated brass. One side has a self sealing 1/2" (DN 15) external thread, while the other side features a 3/4" (DN 20) compression fitting for connecting the 14 mm or 16 mm Schlüter heating pipe. Schlüter -BEKOTEC-THERM-AW Schlüter -BEKOTEC-THERM-AW is a 1/2" x 3/4" angled connection fitting made of nickel plated brass that can be rotated. One side has a self sealing 1/2" (DN 15) external thread, while the other side features a 3/4" (DN 20) compression fitting for connecting the 14 mm or 16 mm Schlüter heating pipe. Schlüter -BEKOTEC-THERM-KU KU = connection coupling Ø mm 16 BTZKU 16 8.43 10 14 BTZKU 14 8.43 10 Schlüter -BEKOTEC-THERM-AN AN = connector fitting Ø mm Set = 2 = set 16 BTZ2AN 16 8.76 10 14 BTZ2AN 14 8.76 10 Schlüter -BEKOTEC-THERM-AW AW = angled connector fitting Ø mm Set = 2 = set 16 BTZ2AW 16 16.90 10 14 BTZ2AW 14 16.90 10 Schlüter -BEKOTEC-THERM-DA Schlüter -BEKOTEC-THERM-DA is a set of twin connectors made of nickel plated brass. It features a ¾ (DN 20) cone joint nut on one side and two ¾ (DN 20) cone connector threads on the other side for connecting the Schlüter heating pipes with diameters of 14 mm or 16 mm. The twin connector allows for setting up a second heating circuit at the control station BTBMS/RT. In this case, the heating circuits must have approximately the same lengths and performance ratings. Schlüter -BEKOTEC-THERM-DA DA = Twin connector Set = 2 = set BTZ 2 DA 37.78 10 Depending on the selected system, the connection to the Schlüter -BEKOTEC-THERM heating pipes requires 2 sets of clamp connections BTZ 2 KV... and two angle clips BTZW 1418. box packaging. 15
Schlüter -BEKOTEC-THERM-W Schlüter -BEKOTEC-THERM-W Schlüter -BEKOTEC-THERM-W is a blank set for retrofitting the calorimeter, partly pre-installed. Vertical components: 1 spacer fitting, length 110 mm, with outside threading 3/4" (DN 20) 2 90 angles 3 ball valves 3/4" (DN 20), nickel plated brass 2 flat gaskets 1" (DN 25) Horizontal components: 1 spacer fitting, length 110 mm, with outside threading 3/4" (DN 20) 3 ball valves 3/4" (DN 20), nickel plated brass 2 flat gaskets 1" (DN 25) W = pre-plumb kit = set BTZW 20 V (vertical) 90.11 5 BTZW 20 H (horizontal) 64.52 5 The blank set for the measuring mechanism of the calorimeter is usually attached to the cold leg. Depending on the connection situation, it may become necessary to attach the distributor terminal for the cold leg above or below. Follow the manufacturer s instructions for the selected calorimeter. The space needs also are important for the selection of the distributor cabinet (see table on page 19). Schlüter -BEKOTEC-THERM-ZV Schlüter -BEKOTEC-THERM-ZV is a heating zone valve that simultaneously operates all heating circuits connected to the Schlüter -BEKOTEC heating circuit distributor by opening or closing. The heating zone valve can be controlled by a Schlüter actuator. The unit is controlled either by Schlüter control components or through an external control unit. Connection/material: threaded connection/valve 1" (DN 25) of nickel plated brass. Schlüter -BEKOTEC-THERM-ZV ZV = heating zones valve BTZZV 34.56 5 During installation, it is important to observe the flow direction shown with an arrow on the valve kvs = 4.2 m 3 / h -316 200 Schlüter -BEKOTEC-THERM-RVT Schlüter -BEKOTEC-THERM-RVT* is a fixed value control station for setting the supply temperature, which connects directly to the Schlüter -BEKOTEC-THERM heating circuit distributor with 2 to 8 heating circuits. The fixed value control unit supplies the Schlüter - BEKOTEC-THERM ceramic thermal comfort floor with the required low supply temperatures by mixing flow and return water. The control station can be installed in Schlüter - BEKOTEC-THERM-VSE distributor cabinets, provided the minimum installation depth is 140 mm and at least 350 mm are added to the distributor cabinet size. The control station is pre-installed with an electronically controlled circulation pump and a 3 way distributor valve. Schlüter -BEKOTEC-THERM-RVT RVT = control station for supply temperature DN 25 BTRVT 690.76 * A qualified expert must examine the control technology and hydraulic conditions before the installation of the unit. The manufacturer s installation and assembly instructions must be observed. -120 G1 G1 16 box packaging.
BTMS Schlüter -BEKOTEC-THERM-BMS Schlüter -BEKOTEC-THERM-BMS/RT The Schlüter -BEKOTEC-THERM-BMS control station is a simple control concept to supply smaller areas equipped with one or two Schlüter -BEKOTEC-THERM heating circuits. The control station Schlüter -BEKOTEC-THERM-BMS/ RT is equipped with an additional interior thermostat that allows for switching the control station depending on room temperature. The control station supplies the Schlüter -BEKOTEC- THERM ceramic thermal comfort floor with the required low supply temperatures by mixing in heating water from warmer heating circuits, e.g. from the radiator circuit. It is suitable for use in the Schlüter -BEKOTEC-THERM distributor cabinet models BTVSE 4 and BTVSV 4. A second heating circuit can be implemented with an available set of twin connectors (order separately, item no.: BTZ 2 DA). In this case, the heating circuits must have approximately the same lengths and performance ratings. For further technical information please refer to the corresponding installation and operating instructions. Schlüter -BEKOTEC-THERM-BMS BMS = Control station BTBMS 550.38 BTBMS/RT 577.58 BTMS/RT Notes: The clamp connections BTZ 2 KV 14 and BTZ 2 KV 16 are not included with the control station and must be ordered separately to match the diameter of the heating pipes. rior to installation, a qualified expert should inspect the control technology and hydraulic installations. The installation and assembly instructions of the manufacturer must be observed. 17
Schlüter -BEKOTEC-THERM-RTB Schlüter -BEKOTEC-THERM-RTB* is a return temperature limiter valve for concealed installation into the wall. It is installed at the end of a Schlüter -BEKOTEC heating circuit and can be utilised to limit the water temperature in the preceding heating circuit. In addition, it serves to control the floor temperature in rooms with existing heaters. The temperature limiter can be adjusted to temperatures ranging from 20 to 40 ºC. The set includes: - Recessed wall installation box with adjustable installation depth W x H x D = 135 x 190 x 57 approx. 75 mm - Aperture, white, W x H = 145 x 200 mm - Two mounting angles - RTB valve made of brass, incl. exhaust valve and flush valve with valve connections AG 3/4" (DN20), which match the clamping ring threading BTZ 2 KV - Thermostat head RTLH for return temperature, adjustable from 20 to 40 C - Installation and assembly manual Schlüter -BEKOTEC-THERM-RTB RTB = return temperature limiter valve = set BTRTB 120.57 5 * see BTRVT A set of clamps BTZ 2 KV is required for connection with the Schlüter -BEKOTEC heating pipe BTHR. The connector fitting BTZ 2 AN or the angled connector fitting BTZ 2 AW can be used at the connection to the existing heating system (see page 15). Schlüter -BEKOTEC-THERM-RTBR Schlüter -BEKOTEC-THERM-RTBR* is a return temperature limiter valve for room temperature control. It is installed in a recessed wall box at the end of the return in a Schlüter -BEKOTEC-THERM floor heating circuit. It can be used for control purposes when the Schlüter - BEKOTEC-THERM heating circuit is to branch off the existing heating circuit to act as a supplementary heating. The temperature limiter can be set up for a temperature range from 20 to 40 C. The room temperature can be adjusted from 7 to 28 C with the help of a thermostat head. The set includes: - Recessed wall installation box with adjustable installation depth W x H x D = 135 x 190 x 57 approx. 75 mm - Two mounting angles - Aperture, white, W x H = 145 x 210 mm - Integrated room temperature control unit with adjustment range from 7 to 28 ºC - RTB valve made of brass, incl. exhaust valve and flush valve with valve connections AG 3/4" (DN20), which match the clamping ring threading BTZ 2 KV - RTB thermostat head for return temperature, adjustable from 20 to 40 C - Installation and assembly manual Schlüter -BEKOTEC-THERM-RTBR RTBR = return temperature limiter valve with room temperature control = set BTRTBR 254.73 5 * see BTRVT A set of clamps BTZ 2 KV is required for connection with the Schlüter -BEKOTEC heating pipe BTHR. The connector fitting BTZ 2 AN or the angled connector fitting BTZ 2 AW can be used at the connection to the existing heating system (see page 15). 18 box packaging.
Schlüter -BEKOTEC-THERM-VSE Schlüter -BEKOTEC-THERM-VSE is a distributor cabinet for concealed mounting to house the Schlüter heating circuit distributor manifold and the matching control components. The concealed cabinet consists of galvanized steel with two stabilising double edges around the perimeter and perforations in the lateral walls for inserting the connector pipes. The unit includes: - Two lateral height adjustable installation pedestals, adjustable from 0 to 90 mm - Screed panel, height adjustable and removable - Heating pipe rail - 2 adjustable attachment rails for Schlüter heating circuit distributor manifold and an additional installation rail for simple plug-in installation of the Schlüter control modules. The powder coated frame and door come in separate packaging and can be installed subsequently with four tuck flaps with wing screws, with variable attachment options for in wall openings of 110 to 150 mm. The door can be closed with a turning latch. Colour: Brilliant white a lock with standard keys is available as a special accessory (item no BTZS). Schlüter -BEKOTEC-THERM-VSE Distributor cabinet for concealed mounting Outside dimensions (W x H x D = mm) Inside dim. (B = mm) Max. heating Max. heating circuits circuits without W* with W* vertical Max. heating circuits with W* horizontal Max. heating circuits with RVT ** BTVSE 4 BW 490 x 705 x110 455 4 2 0 107.53 5 BTVSE 5 BW 575 x 705 x110 540 5 4 2 118.52 5 BTVSE 8 BW 725 x 705 x110 690 8 7 5 2 137.16 5 BTVSE 11 BW 875 x 705 x110 840 11 9 7 5 154.22 5 BTVSE 12 BW 1025 x 705 x110 990 12 12 11 8 173.29 5 BTZS Distributor cabinet lock with 2 standard keys 12.43 5 * W = blank set for calorimeter ** RVT = fixed value control station BTRVT (minimum installation dept 140 mm) Schlüter -BEKOTEC-THERM-VSV Schlüter -BEKOTEC-THERM-VSV is a distributor cabinet for surface mounting to house the Schlüter heating circuit distributor manifold and the matching control components. The distributor cabinet consists of galvanized steel, with powder coating on the inside and outside. The unit includes: - Two lateral height adjustable installation pedestals, adjustable from 0 to 90 mm - Screed panel, removable - Heating pipe rail - 2 adjustable attachment rails for Schlüter heating circuit distributor manifold and an additional installation rail for simple plug-in installation of the Schlüter control modules Cabinet depth: 125 mm. The door can be closed with a turning latch. a lock with standard keys is available as a special accessory (item no BTZS). Schlüter -BEKOTEC-THERM-VSV Distributor cabinet for wall mounting Outside dimensions (W x H x D = mm) Inside dim. (B = mm) Max. heating Max. heating circuits circuits without W* with W* vertical Max. heating circuits with W* horizontal Max. heating circuits with RVT** BTVSV 4 BW 496 x 620 x125 493 4 2 0 145.26 5 BTVSV 5 BW 582 x 620 x125 579 5 4 2 154.63 5 BTVSV 8 BW 732 x 620 x125 729 8 7 5 167.54 5 Installation not possible BTVSV 11 BW 882 x 620 x125 878 11 9 7 179.29 5 BTVSV 12 BW 1032 x 620 x125 1029 12 12 10 204.37 5 BTZS Distributor cabinet lock with 2 standard keys 12.43 5 * W = blank set for calorimeter ** RVT = fixed value control station BTRVT box packaging. 19
Schlüter -BEKOTEC-THERM-ER/C Schlüter -BEKOTEC-THERM-ER/C is an interior thermostat of the type Control available in 230 or 24 with removable digital clock for programming the time controlled electronic temperature settings. The digital clock is suitable for programming daily or weekly programs with eight switch times (4 times on /4 times off) and can be used for the time control of a room or as a pilot clock for several rooms (room group control). Manual settings for daylight savings time ± 1 hour, power reserve for 100 hours. The target temperature can be set on a dial from 10 to 28 C and can be limited by a set point limit. An adjustable, time controlled temperature reduction mechanism of 2 to 6 C is integrated. The operating status Temperature decrease on/off is shown by an LED and can also be activated manually if required. A pulse width modulation is integrated to prevent variations in room temperature. Schlüter -BEKOTEC-THERM-ER/C ER/C = interior thermostat Control The unit is easy to install by plugging into the previously installed mounting socket for the interior thermostat. Colour: BW = Brilliant white Dimensions: W/H/D 118 x 79 x 27mm 230 V BTER 230 C/BW 188.79 10 24 V BTER 24 C/BW 188.79 10 Be sure to order mounting socket Schlüter -BEKOTEC-THERM-ER/M ( BTERM) separately. Schlüter -BEKOTEC-THERM-ER/K Schlüter -BEKOTEC-THERM-ER/K is an interior thermostat of the type Comfort available in 230 or 24 with electronic temperature control. The target temperature can be set on a dial from 10 to 28 C and can be limited by a set point limit. A time controlled temperature reduction of 2 to 6 C is possible by using the Schlüter -BEKOTEC-THERM-ER/C unit as a pilot clock or adding the control module expansion Schlüter -BEKOTEC-THERM-ESME/T with timer. The operating status Temperature decrease on/off is shown by an LED and can also be activated manually if required. A pulse width modulation is integrated to prevent variations in room temperature. The unit is easy to install by plugging into the previously installed mounting socket for the interior thermostat. Schlüter -BEKOTEC-THERM-ER/K ER/C = interior thermostat Comfort Colour: BW = Brilliant white Dimensions: W/H/D 93 x 79 x 27mm 230 V BTER 230 K/BW 55.73 10 24 V BTER 24 K/BW 55.73 10 Be sure to order mounting socket Schlüter -BEKOTEC-THERM-ER/M ( BTERM) separately. Schlüter -BEKOTEC-THERM-ER/S Schlüter -BEKOTEC-THERM-ER/S is an interior ther mostat of the type Standard available in 230 or 24 with electronic temperature control. The target temperature can be set on a dial from 10 to 28 C and can be limited by a set point limit. A time controlled temperature reduction of 2 C is possible by using the Schlüter -BEKOTEC-THERM-ER/C unit as a pilot clock or adding the control module expansion Schlüter -BEKOTEC-THERM-ESME/T with timer. A pulse width modulation is integrated to prevent variations in room temperature. The unit is easy to install by plugging into the previously installed mounting socket for the interior thermostat. Schlüter -BEKOTEC-THERM-ER/S ER/S = interior thermostat Standard Colour: BW = Brilliant white Dimensions: W/H/D 84 x 79 x 27mm 230 V BTER 230 S/BW 41.39 10 24 V BTER 24 S/BW 41.39 10 Be sure to order mounting socket Schlüter -BEKOTEC-THERM-ER/M ( BTERM) separately. 20 box packaging.
Schlüter -BEKOTEC-THERM-ERF/K Schlüter -BEKOTEC-THERM-ERF/K is a wireless interior thermostat of the type Comfort for wireless electronic temperature control. The target temperature can be set on a dial from 10 to 28 C and can be limited by a set point limit. A time controlled temperature reduction of 2 to 6 C is possible by adding the control module expansion with timer, Schlüter -BEKOTEC-THERM-ER/C. The operating status Temperature decrease on/off is shown by an LED and can also be activated manually if required. A pulse width modulation is integrated to prevent vari ations in room temperature. Schlüter -BEKOTEC-THERM-ER/KKH Schlüter -BEKOTEC-THERM-ER/KKH is a thermostat for cooling/heating with electronic temperature control for cooling and heating in a 24 version. The temperature reference value is adjustable from 10 to 28 ºC with the help of a dial and can be limited by a reference value limiter. A time controlled temperature change from 2 to 6 ºC is possible. The operating modes are shown with separate LED indicators. The control module extension ESME24KH must be used for heating/cooling switches of all thermostats connected to the Schlüter -BEKOTEC-THERM control module (24 ). A pulse width modulation is integrated to prevent variations in room temperature. The unit is easy to install and is simply plugged into the previously installed thermostat mounting base. Schlüter -BEKOTEC-THERM-ERF/K ERF/K = wireless interior thermostat BTERFK/BW 119.16 10 Colour: BW = Brilliant white Dimensions: W/H/D 93 x 79 x 27 mm A mounting socket is not required. Batteries are included in delivery. Schlüter -BEKOTEC-THERM-ER/KKH ER/KKH = interior thermostat cooling/heating = BTER24KKH/BW 101.33 10 Colour: BW = Brilliant white Dimensions W/H/D: 93 x 79 x 27 mm. The cooling mode only offers basic cooling without exact temperature control. lease order the mounting base Schlüter -BEKOTEC-THERM- ERM (part no. BTERM) separately. Only control components for 24 can be used. Schlüter -BEKOTEC-THERM-ERM Schlüter -BEKOTEC-THERM-ERM is a mounting base for the electronically controlled Schlüter thermostats ER/C, ER/K, ER/S, and ER/KKH, 230 or 24. The unit can be installed over a conventional, concealed junction box. Schlüter -BEKOTEC-THERM-ERM ERM = mounting socket for interior thermostats 230/24 BTERM 6.15 10 Schlüter -BEKOTEC-THERM-ESA Schlüter -BEKOTEC-THERM-ESA is an actuator for either 230 or 24 to control the flow of the cold leg valves. It is mounted by plugging into the valves of the cold leg of the Schlüter heating circuit distributor. Actuators are equipped with a volume display, including a control function of the valve adapters and a protection mechanism against moisture. The valve is delivered in open condition (first open function). Zero current circuit. Connector cable 1 m, plug-in type. Schlüter -BEKOTEC-THERM-ESA ESA = actuator 230 V BTESA 230 32.80 10 24 V BTESA 24 32.80 10 Dimension W/H/D: 54 x 43 x 53 mm Wireless control requires the 24 actuator. box packaging. 21
230 24 Schlüter -BEKOTEC-THERM-ESM R6 Schlüter -BEKOTEC-THERM-ESM R6 is a control module available in 230 or 24 as a switch connection between Schlüter interior thermostats and actuators. The unit is installed by simply plugging into the installation rail of the Schlüter distributor cabinet. The cable connections to the main supply and the Schlüter actuators and interior thermostats are simple plug-in clamps. The allocation is clearly labelled with colour coding. The switching capacity is designed for a maximum of six interior thermostats (= 6 rooms) with 1-4 actuators (heating circuits), with a maximum limit of 14 actuators per control module. Function displays for Operating power, Fuse, and Switched output to interior thermostat ON. The Schlüter Control module 24 is equipped with an integrated transformer. Schlüter -BEKOTEC-THERM-ESM R6 ESM = control module 230 V BTESM 230 R6 95.63 5 24 V BTESM 24 R6 130.24 5 Dimensions W/H/D: 230 : 238 x 75 x 70 mm 24 : 305 x 75 x 70 mm The following expansion modules can be added for 230 or 24 models with plugin connections: -Schlüter -BEKOTEC-THERM-ESME/T -Schlüter -BEKOTEC-THERM-ESME/SA -Schlüter -BEKOTEC-THERM-ESME/R -Schlüter -BEKOTEC-THERM-ESME/ -Schlüter -BEKOTEC-THERM-ESME/D -Schlüter -BEKOTEC-THERM-ESME/24KH 230 Schlüter -BEKOTEC-THERM-ESM R1 Schlüter -BEKOTEC-THERM-ESM R1 is a 230 or 24 control module that serves as the switched connection between the interior thermostats and the actuators. The modules are simply plugged into the installation rail that is integrated into the Schlüter distribution cabinet. The wiring connections for power supply and with the Schlüter actuators and interior thermostats are designed as simple plug-in connections. The connections are clearly labelled with colour coding. The switching capacity is designed for interior thermostats with 1-4 actuators (= heating circuits). The control features a functional display for Supply voltage, Fuse and Thermostat output activated. The Schlüter 24 control module is equipped with an integrated transformer. Schlüter -BEKOTEC-THERM-ESM R1 ESM R1 = Control module for single room 230 V BTESM 230 R1 58.23 5 24 V BTESM 24 R1 98.13 5 Dimensions W/H/D: 230 = 88 x 75 x 70 mm 24 = 157 x 75 x 70 mm The following expansion modules can be added for 230 or 24 models with plugin connections: -Schlüter -BEKOTEC-THERM-ESME/T -Schlüter -BEKOTEC-THERM-ESME/SA -Schlüter -BEKOTEC-THERM-ESME/R -Schlüter -BEKOTEC-THERM-ESME/ -Schlüter -BEKOTEC-THERM-ESME/D -Schlüter -BEKOTEC-THERM-ESME/24KH 24 22 box packaging.
Schlüter -BEKOTEC-THERM-ESMF Schlüter -BEKOTEC-THERM-ESMF is a wireless control module with either 6 or 12 channels (interior thermostats) and integrated 24 transformer as a switch connection between Schlüter wireless interior thermostats and actuators. The unit is installed by simply plugging in to the installation rail of the Schlüter distributor cabinet. The cable connections to the main supply and the Schlüter actuators and interior thermostats are simple plug-in clamps. The allocation is clearly labelled with colour coding. The switching capacity is designed for max. 6 or 12 channels (interior thermostats) with 1-4 actuators (heating circuits) each, with a maximum limit of 13 actuators. The interior thermostats can be freely allocated to 1-4 actuators per channel. Function displays for operating power 24, wireless reception control, Switched output to interior thermostat ON. rotection switch in case of interior thermostat failure (freeze protection mode). Wireless transmission test required before operation. Schlüter -BEKOTEC-THERM-ESMF ESMF = wireless control module Channels 6 BTESMF 24R6 386.50 5 12 BTESMF 24R12 510.18 5 Dimensions: W/H/D: 305 x 75 x 70 mm The following expansion models of the 24 type can be plugged in: -Schlüter -BEKOTEC-THERM-ESME/T -Schlüter -BEKOTEC-THERM-ESME/SA -Schlüter -BEKOTEC-THERM-ESME/ -Schlüter -BEKOTEC-THERM-ESME/D -Schlüter -BEKOTEC-THERM-ESME/24KH Schlüter -BEKOTEC-THERM-ESME/T Schlüter -BEKOTEC-THERM-ESME/T is a control module expansion with timer/digital clock and LCD display. It allows for programming two separate heating zones (room group control). Daily and weekly programs, with weekday blocks, and daylight savings time settings can be programmed. 42 memory locations, 120 hours of power reserve. Simple installation by plug-in connection. Suitable for 230, 24, and wireless operation. Schlüter -BEKOTEC-THERM-ESME/T ESME/T = control module expansion with timer as digital clock BTESMET 220.51 5 Dimension W/H/D: 65 x 75 x 46 mm Schlüter -BEKOTEC-THERM-ESME/SA Schlüter -BEKOTEC-THERM-ESME/SA is a control module expansion for 230 or 24 for connecting 1-8 additional actuators to an interior thermostat or 1-4 actuators each to two interior thermostats of the control module. A plug-in jumper takes care of the allocation to the corresponding interior thermostats. Simple installation by plug-in connection. Suitable for 230, 24, and wireless operation. Schlüter -BEKOTEC-THERM-ESME/SA ESME/SA = control module expansion for actuators 230 V BTESME 230 SA 59.45 5 24 V BTESME 24 SA 59.45 5 Dimension W/H/D: 88 x 75 x 70 mm The 24 expansion is to be used for wireless operation. Maximum number of actuators per control module: 14 (wireless: 13) box packaging. 23
Schlüter -BEKOTEC-THERM-ESME/R Schlüter -BEKOTEC-THERM-ESME/R is a control module expansion for connecting 1 or 2 additional interior thermostats with 1-4 actuators each. Simple installation by plug-in connection. Suitable for 230, 24, and wireless operation. Schlüter -BEKOTEC-THERM-ESME/R ESME/R = control module expansion for interior thermostat 230 V BTESME 230 R 47.94 5 24 V BTESME 24 R 47.94 5 Dimension W/H/D: 88 x 75 x 70 mm Maximum number of actuators per control module: 14 Schlüter -BEKOTEC-THERM-ESME/ Schlüter-BEKOTEC-THERM-ESME/ is a control module expansion for pump control. The circulating pump is switched off when all actuators are closed. The wake flow time can be set to 0, 5, 10, or 15 minutes. Heating zones / control module operation mode can be allocated by plug-in jumpers. Simple installation by plug-in connection. Suitable for 230, 24 and wireless operation. Schlüter -BEKOTEC-THERM-ESME/ ESME/ control module expansion for pump control Dimension W/H/D: 88 x 75 x 70 mm 230 V BTESME 230 86.29 5 24 V BTESME 24 86.29 5 Schlüter -BEKOTEC-THERM-ESME/D Schlüter -BEKOTEC-THERM-ESME/D is a control module expansion dual pump module, which allows for pump control and the addition of another electrical consumer (e.g. a boiler). The circulating pump and another consumer are switched off when all actuators are closed. The follow on time can be set to 0, 5, 10, or 15 minutes. Simple plug-in installation, suitable for 230, 24, or wireless systems. Schlüter -BEKOTEC-THERM-ESME/D ESME/D = control module expansion dual pump module Dimension W/H/D: 88 x 75 x 70 mm 230 V BTESME 230 D 101.11 5 24 V BTESME 24 D 101.11 5 Schlüter -BEKOTEC-THERM-ESME/KH Schlüter -BEKOTEC-THERM-ESME/KH is a control module extension for cooling / heating that can switch all KKH thermostats connected to the Schlüter - BEKOTEC-THERM control module (24 ) from cooling to heating and vice versa. The switching takes place by way of a potential free contact on the side of the heat or cold generator or manually by pushing the set button on the control module extension. The operating modes (cooling, heating, or automatic mode) are indicated by LEDs. Simple plug-in installation. Suitable for 24 only. Schlüter -BEKOTEC-THERM-ESME/KH ESME/KH = control module extension cooling/heating Dimensions L/H/D: 88 x 75 x 70 mm 24 V BTESME 24 KH 120.35 5 the control module extension cooling/ heating requires cooling/heating thermostats. 24 box packaging.
Schlüter -BEKOTEC-THERM-ESME/S Schlüter -BEKOTEC-THERM-ESME/S is a control module extension in the form of a program plug for combining the base controls of channels C1 and C2 at the control module BTESM/R6. Channel C1 corresponds to the interior thermostat connections 1, 2, and 3, while channel C2 corresponds to the interior thermostat connections 4, 5, and 6 of the BTESM/R6 control module. The program plug is used for the timed control of the interior thermostats connected to channels C1 and C2 via an interior thermostat of the Control series. The item is simply plugged into the control module or the last control module extension. Schlüter -BEKOTEC-THERM-ESME/S ESME/S = Control module extension rogram plug 230 V BTESME 230 S 16.10 5 24 V BTESME 24 S 16.10 5 25