TC411BP/BF TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC411BP,TC411BF TC411B BCD-to-Seven Segment Latch/Decoder/Driver TC411B is decoder which converts the input of BCD code into the 7 segment display element driving signal and the output has complementary connection of NPN bipolar traistor and N-channel MOS FET. Therefore, not only capability of directly driving cathode common type LED, this has capability of driving various display elements with simple interface circuits. LT input and BI input are to force all the outputs to be H (illuminated) and L (not illuminated) respectively regardless of BCD input. As the latch controlled by common LE input is ierted in each of four input lines, static display of dynamic information can be achieved. When an invalid BCD input, or higher is applied, all the outputs become L (not illuminated). TC411BP TC411BF Pin Assignment Display Weight DIP16-P-300-2.4A SOP16-P-300-1.27A SOP16-P-300-1.27 : 1.00 g (typ.) : 0.18 g (typ.) : 0.18 g (typ.) 1
TC411BP/BF Truth Table Inputs Outputs LE BI LT D C B A a b c d e f g * * L * * * * H H H H H H H 8 Display Mode * L H * * * * L L L L L L L Blank L H H L L L L H H H H H H L 0 L H H L L L H L H H L L L L 1 L H H L L H L H H L H H L H 2 L H H L L H H H H H H L L H 3 L H H L H L L L H H L L H H 4 L H H L H L H H L H H L H H L H H L H H L L L H H H H H 6 L H H L H H H H H H L L L L 7 L H H H L L L H H H H H H H 8 L H H H L L H H H H L L H H 9 L H H H L H L L L L L L L L Blank L H H H L H H L L L L L L L Blank L H H H H * * L L L L L L L Blank H H H * * * * *: Don t care : Depends upon the BCD code previously applied when LE L 2
TC411BP/BF Logic Diagram 3
TC411BP/BF Absolute Maximum Ratings (Note) Characteristics Symbol Rating Unit DC supply voltage V DD V SS 0.~V SS + 20 V Input voltage V IN V SS 0.~V DD + 0. V Output voltage V OUT V SS 0.~V DD + 0. V DC input current I IN ± ma Output high current I OH 0 ma Power dissipation P D 300 (DIP)/180 (SOIC) mw Operating temperature range T opr 40~8 C Storage temperature range T stg 6~10 C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Recommended Operating Conditio (V SS = 0 V) (Note) Characteristics Symbol Test Condition Min Typ. Max Unit DC supply voltage V DD 3 18 V Input voltage V IN 0 V DD V Note: The recommended operating conditio are required to eure the normal operation of the device. Unused inputs must be tied to either VCC or GND. 4
TC411BP/BF Static Electrical Characteristics (V SS = 0 V) Characteristics High-level output voltage Low-level output voltage Symbol V OH I OUT < 1 µa V IN = V SS, V DD V OL I OUT < 1 µa V IN = V SS, V DD Test Condition 40 C 2 C 8 C I OH = 0 ma I OH = ma I OH = 20 ma V IN = V DD, V SS V DD (V) 1 1 Min Max Min Typ. Max Min Max 4.1 9.1 14.1 4. 3.90 3. 0.0 0.0 0.0 4.1 9.1 14.1 4. 3.90 3. 4.41 9.41 14.41 0.00 0.00 0.00 4.41 4.2 4.19 0.0 0.0 0.0 4.2 9.2 14.2 4.20 3.90 3.30 0.0 0.0 0.0 Unit V V I OH = 0 ma 9. 9. 9.41 9.20 Output high voltage V OH I OH = ma I OH = 20 ma 9.00 8.70 9.00 8.70 9.2 9.20 9.00 8.40 V V IN = V DD, V SS I OH = 0 ma 14. 14. 14.41 14.20 I OH = ma 1 14.00 14.00 14.26 14.00 I OH = 20 ma 13.7 13.7 14.21 13.0 V IN = V DD, V SS V OUT = 0.4 V 0.61 0.1 1.2 0.42 Output low voltage I OL V OUT = 0. V V OUT = 1. V 1 1. 4.0 1.3 3.4 3.2 12.0 1.1 2.8 ma V IN = V DD, V SS Input high voltage Input low voltage Input current Quiescent supply current V IH V IL V OUT = 0. V, 4. V V OUT = 1.0 V, 9.0 V V OUT = 1. V, 13. V I OUT < 1 µa V OUT = 0. V, 4. V V OUT = 1.0 V, 9.0 V V OUT = 1. V, 13. V I OUT < 1 µa 1 1 3. 7.0 11.0 1. 3.0 4.0 3. 7.0 11.0 2.7.0 8.2 2.2 4. 6.7 1. 3.0 4.0 3. 7.0 11.0 H level I IH V IH = 18 V 18 0.3 0.3 1.0 L level I IL V IL = 0 V 18 0.3 0.3 1.0 I DD V IN = V SS, V DD (Note) 1 20 0.00 0.0 0.01 20 1. 3.0 4.0 10 300 600 V V µa µa Note: All valid input combinatio.
Dynamic Electrical Characteristics (Ta = 2 C, V SS = 0 V, C L = 0 pf, R L = kω) TC411BP/BF Characteristics Symbol Test Condition V DD (V) Min Typ. Max Unit 2 80 Output traition time t TLH 1 60 (low to high) 1 1 0 Output traition time (high to low) t THL 70 3 200 0 1 30 80 (DATA-OUT) t plh 1 200 90 6 40 420 300 230 40 t phl 1 420 (DATA-OUT) 1 80 300 7 640 t plh 4 260 ( BI -OUT) 1 3 200 90 640 t phl 0 260 ( BI -OUT) 1 4 200 60 300 t plh 40 10 ( LT -OUT) 1 3 0 7 300 t phl 4 10 ( LT -OUT) 1 3 0 180 600 t plh 90 300 (LE-OUT) 1 6 20 (LE-OUT) t phl 230 1 600 300 1 8 20 Min pulse time (LE) t WL 1 40 20 1 300 10 120 3 10 Min set-up time t SU 1 70 (DATA-LE) 1 40 0 Min hold time t H 0 (DATA-LE) 1 0 Input capacitance C IN 7. pf 6
TC411BP/BF Waveform for Measurement of Dynamic Characteristics Waveform 1 Waveform 2 Waveform 3 Waveform 4 7
TC411BP/BF Package Dimeio Weight: 1.00 g (typ.) 8
TC411BP/BF Package Dimeio Weight: 0.18 g (typ.) 9
TC411BP/BF Package Dimeio Weight: 0.18 g (typ.)
TC411BP/BF Note: Lead (Pb)-Free Packages DIP16-P-300-2.4A SOP16-P-300-1.27A RESTRICTIONS ON PRODUCT USE 060116EBA The information contained herein is subject to change without notice. 0223_D TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical seitivity and vulnerability to physical stress. It is the respoibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situatio in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your desig, please eure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specificatio. Also, please keep in mind the precautio and conditio set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc. 0223_A The TOSHIBA products listed in this document are intended for usage in general electronics applicatio (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ( Unintended Usage ). Unintended Usage include atomic energy control itruments, airplane or spaceship itruments, traportation itruments, traffic signal itruments, combustion control itruments, medical itruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer s own risk. 0223_B The products described in this document shall not be used or embedded to any dowtream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulatio. 0606_Q The information contained herein is presented only as a guide for the applicatio of our products. No respoibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No licee is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 0223_C The products described in this document are subject to the foreign exchange and foreign trade laws. 0223_E 11