Effect of Rotatory Inertia and Load Natural. Frequency on the Response of Uniform Rayleigh. Beam Resting on Pasternak Foundation

Similar documents
Deflection profile analysis of beams on two-parameter elastic subgrade

Indian railway track analysis for displacement and vibration pattern estimation

Finite Difference Dynamic Analysis of Railway Bridges Supported by Pasternak Foundation under Uniform Partially Distributed Moving Railway Vehicle

Dynamic Green Function Solution of Beams Under a Moving Load with Dierent Boundary Conditions

COPYRIGHTED MATERIAL. Index

Stochastic vibration of laminated composite coated beam traversed by a random moving load

Dynamic analysis of railway bridges by means of the spectral method

Structural Dynamics Lecture Eleven: Dynamic Response of MDOF Systems: (Chapter 11) By: H. Ahmadian

Introduction to Continuous Systems. Continuous Systems. Strings, Torsional Rods and Beams.

International Journal of Advance Engineering and Research Development

DYNAMIC EFFECTS OF VISCOUS DAMPING ON ISOTROPIC RECTANGULAR PLATES RESTING ON PASTERNAK FOUNDATION, SUBJECTED TO MOVING LOADS

Computational Simulation of Dynamic Response of Vehicle Tatra T815 and the Ground

Free vibrations of a multi-span Timoshenko beam carrying multiple spring-mass systems

Table of Contents. Preface... 13

VIBRATION PROBLEMS IN ENGINEERING

The Effect of Distribution for a Moving Force

Determination of Young's Modulus by Using. Initial Data for Different Boundary Conditions

FREE VIBRATIONS OF UNIFORM TIMOSHENKO BEAMS ON PASTERNAK FOUNDATION USING COUPLED DISPLACEMENT FIELD METHOD

Shape Optimization of Revolute Single Link Flexible Robotic Manipulator for Vibration Suppression

1859. Forced transverse vibration analysis of a Rayleigh double-beam system with a Pasternak middle layer subjected to compressive axial load

Analysis of Infinitely Long Euler Bernoulli Beam on Two Parameter Elastic Foundation: Case of Point Load

NONLINEAR ANALYSIS OF A FUNCTIONALLY GRADED BEAM RESTING ON THE ELASTIC NONLINEAR FOUNDATION

Introduction to structural dynamics

Dynamic Behaviour of a Cantilever Beam Subjected To Moving Mass and Elastic End Constraint

A STUDY ON THE WHEELSET/SLAB TRACK VERTICAL INTERACTION

Vibration of Thin Beams by PIM and RPIM methods. *B. Kanber¹, and O. M. Tufik 1

Transactions on Modelling and Simulation vol 18, 1997 WIT Press, ISSN X

Consider an elastic spring as shown in the Fig.2.4. When the spring is slowly

Forced Vibration Analysis of Timoshenko Beam with Discontinuities by Means of Distributions Jiri Sobotka

Vibration analysis of concrete bridges during a train pass-by using various models

Parametric Study of Thermal Stability on Continuous Welded Rail

DYNAMIC CHARACTERISTICS OF ELASTICALLY SUPPORTED BEAM SUBJECTED TO A COMPRESSIVE AXIAL FORCE AND A MOVING LOAD

Final Exam Solution Dynamics :45 12:15. Problem 1 Bateau

202 Index. failure, 26 field equation, 122 force, 1

Flexural Behavior of Laterally Loaded Tapered Piles in Cohesive Soils

Free vibration analysis of elastically connected multiple-beams with general boundary conditions using improved Fourier series method

Structural Dynamics. Spring mass system. The spring force is given by and F(t) is the driving force. Start by applying Newton s second law (F=ma).

The... of a particle is defined as its change in position in some time interval.

Vibrations of Fluid-Conveying Pipes Resting on Two-parameter Foundation

Step 1: Mathematical Modeling

Mathematical modeling of three-layer beam hydroelastic oscillations

Quintic beam closed form matrices (revised 2/21, 2/23/12) General elastic beam with an elastic foundation

Pune, Maharashtra, India

Research Article Free Vibration Analysis of an Euler Beam of Variable Width on the Winkler Foundation Using Homotopy Perturbation Method

Flow-Induced Vibration of Pipeline on Elastic Support

Lecture 15 Strain and stress in beams

ME 475 Modal Analysis of a Tapered Beam

Advanced Vibrations. Distributed-Parameter Systems: Exact Solutions (Lecture 10) By: H. Ahmadian

Dr.Vinod Hosur, Professor, Civil Engg.Dept., Gogte Institute of Technology, Belgaum

MCE503: Modeling and Simulation of Mechatronic Systems. Modeling of Continuous Beams: Finite-Mode Approach

Response of a completely free beam on a tensionless Pasternak foundation subjected to dynamic load

General elastic beam with an elastic foundation

STRUCTURAL DYNAMICS BASICS:

Vibration of solids and structures under moving loads

Effect of periodicity of railway track and wheel rail interaction on wheelset track dynamics

Stresses and Strains in flexible Pavements

Dynamics of Railway Track

P. M. Pankade 1, D. H. Tupe 2, G. R. Gandhe 3

Analysis of Local Vibration for High-Speed Railway Bridge Based on Finite Element Method

Presented By: EAS 6939 Aerospace Structural Composites

Finite Element Analysis of Dynamic Properties of Thermally Optimal Two-phase Composite Structure

Vibration analysis of circular arch element using curvature

Part D: Frames and Plates

FINITE GRID SOLUTION FOR NON-RECTANGULAR PLATES

Numerical Solution of Non-Linear Biharmonic. Equation for Elasto-Plastic Bending Plate

Vibro-Impact Dynamics of a Piezoelectric Energy Harvester

The Shifted Data Problems by Using Transform of Derivatives

CIVL 8/7117 Chapter 12 - Structural Dynamics 1/75. To discuss the dynamics of a single-degree-of freedom springmass

Analytical Strip Method for Thin Isotropic Cylindrical Shells

Vibrations of string. Henna Tahvanainen. November 8, ELEC-E5610 Acoustics and the Physics of Sound, Lecture 4

Computational Modeling of Conjugated Aerodynamic and Thermomechanical Processes in Composite Structures of High-speed Aircraft

D : SOLID MECHANICS. Q. 1 Q. 9 carry one mark each.

PLAT DAN CANGKANG (TKS 4219)

DISTORTION ANALYSIS OF TILL -WALLED BOX GIRDERS

FLEXIBILITY METHOD FOR INDETERMINATE FRAMES

MODIFIED HYPERBOLIC SHEAR DEFORMATION THEORY FOR STATIC FLEXURE ANALYSIS OF THICK ISOTROPIC BEAM

Mechanics of Inflatable Fabric Beams

Dynamics of Nonlinear rectangular plates subjected to an orbiting mass based on shear deformation plate theory

VIBRATION ANALYSIS OF EULER AND TIMOSHENKO BEAMS USING DIFFERENTIAL TRANSFORMATION METHOD

Basic Energy Principles in Stiffness Analysis

Introduction to Vibration. Professor Mike Brennan

Large-Amplitude Periodic Oscillations in Suspension Bridges

2008 International ANSYS Conference

First-Order Solutions for the Buckling Loads of Euler-Bernoulli Weakened Columns

Vibro-acoustic response of FGM plates considering the thermal effects Tieliang Yang1, a, Qibai Huang1, *

2 marks Questions and Answers

Mechanics of Materials II. Chapter III. A review of the fundamental formulation of stress, strain, and deflection

AEROELASTIC ANALYSIS OF SPHERICAL SHELLS

THE INFLUENCE OF WARPING AND WINKLER-PASTERNAK SOIL ON THE TORSIONAL VIBRATIONS OF THIN-WALLED OPEN SECTION BEAMS WITH GUIDED-END CONDITIONS

Open Access Prediction on Deflection of V-core Sandwich Panels in Weak Direction

The Homotopy Perturbation Method for free vibration analysis of beam on elastic foundation

2. Determine the deflection at C of the beam given in fig below. Use principal of virtual work. W L/2 B A L C

This equation of motion may be solved either by differential equation method or by graphical method as discussed below:

FREE VIBRATION OF BEAM ON CONTINUOUS ELASTIC SUPPORT BY ANALYTICAL AND EXPERIMENTAL METHOD

Dynamic Analysis of Burried Pipelines under Linear Viscoelastic Soil Condition

A New Method of Analysis of Continuous Skew Girder Bridges

CO-ROTATIONAL DYNAMIC FORMULATION FOR 2D BEAMS

INELASTIC RESPONSES OF LONG BRIDGES TO ASYNCHRONOUS SEISMIC INPUTS

DYNAMIC RESPONSE OF A MULTI-SPAN CURVED BEAM FROM MOVING TRANSVERSE POINT LOADS AMANDA D. ALEXANDER

on the figure. Someone has suggested that, in terms of the degrees of freedom x1 and M. Note that if you think the given 1.2

Transcription:

Applied Mathematical Sciences, Vol. 12, 218, no. 16, 783-795 HIKARI Ltd www.m-hikari.com https://doi.org/1.12988/ams.218.8345 Effect of Rotatory Inertia and Load Natural Frequency on the Response of Uniform Rayleigh Beam Resting on Pasternak Foundation Subjected to a Harmonic Magnitude Moving Load A. Jimoh 1 and E. O. Ajoge 2 1 Department of Mathematical Sciences Kogi State University, Anyigba, Nigeria 2 Centre for Energy Research and Development Obafemi Awolowo University, Ile-Ife, Nigeria Copyright 218 A. Jimoh and E. O. Ajoge. This article is distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Abstract In this study, the effect of rotatory inertia on the transverse motion of uniform Rayleigh beam resting on Pasternak foundation subjected to harmonic magnitude moving load is investigated. We employed Fourier sine transform, Laplace integral transformation and convolution theorem as solution technique. It was observed from the results that, the amplitude of the deflection profile of the beam decreases with increase in the value of rotatory inertia and load natural frequency. Also increases in the values of the other structural parameters like shear modulus, foundation modulus, axial force, and damping coefficient lead to decreases in the deflection profile of the beam. It was also observed that the effect of the load natural frequency is more noticeable than that of the rotatory inertia. Keywords: Rotatory inertia, load natural frequency, harmonic load, moving load, Pasternak foundation, damping coefficient, axial force, shear modulus, foundation

784 A. Jimoh and E. O. Ajoge 1 Introduction The calculation of the dynamic response of elastic structures (beams, plates and shells) carrying one or more traveling loads (moving trains, tracks, cars, bicycles, cranes, etc.) is very important in Engineering, Physics and Applied Mathematics as applications relate, for example, to the analysis and design of highway, railway bridges, cable-railroads and the like. Generally, emphasis is placed on the dynamics of the elastic structural members rather on that of the moving loads. Among the earliest researchers on the dynamic analysis of an elastic beam was Ayre et al [1] who studied the effect of the ratio of the weight of the load to the weight of a simply supported beam of a constantly moving mass load. Kenny [2] similarly investigated the dynamic response of infinite elastic beams on elastic foundation under the influence of load moving at constant speeds. He included the effects of viscous damping in the governing differential equation. Steel [3] also investigated the response of a finite simplify supported Bernouli-Euler beam to a unit force moving at a uniform velocity. He analysed the effects of this moving force on beams with and without an elastic foundation. Oni [4] considered the problem of a harmonic time-variable concentrated force moving at uniform velocity over a finite deep beam. In the recent years, several other researchers that made tremendous feat in the study of dynamic of structures under moving loads include Chang and Liu [5], Oni and Omolofe [6], Oni and Awodola [7], Misra [8], Oni and Ogunyebi [9], Hsu [1], Achawakorn and Jearsiri Pongkul [11]. However, all the aforementioned researchers considered only the winkler approximation model which has been criticised variously by authors [12, 13, 14] because it predict discontinuities in the deflection of the surface of the foundation at the ends of a finite beam, which is in contradiction to observation made in practice. To this end, in a more recent time, researchers who considered the dynamic response of elastic beam resting on Pasternak foundation are Coskum [15], Oni and Jimoh [16], Guter [17], Oni and Ahmed [18], Oni and Ahmed [19], Ma et al [2] and Ahmed [21]. In all those researches, rotatory inertia and load natural frequency were neglected. Thus, in this paper, we investigate the effect of rotatory intertia and load natural frequency on the response of uniform Rayleigh beam resting on Pasternak foundation and subjected to harmonic magnitude moving loads. 2. Mathematical Model This paper considered the dynamic response of a uniform Rayleigh beam resting on Pasternak foundation when it is under the action of a harmonic magnitude moving load. The governing partial differential equation that described the motion of the dynamical system is given by [22]

Effect of rotatory inertia and load natural frequency 785 EI 4 V(x,t) x 4 P(x, t) + μ 2 V(x,t) x 2 N 2 V(x,t) x 2 μr 2 4 V(x,t) x 2 t 2 v(x,t) + Σ + PG(x, t) = t (1) EI is the flexural rigidity of the beam, μ is the mass of the beam per unit length L, N is the axial force, Σ is the damping coefficient, PG is the foundation reaction, E is the young s modulus of the beam, I is the moment of inertia of the beam, K is the foundation modulus, P(x, t) is the transverse moving load, x is the spatial coordinate and t is the time The boundary condition at the end x = and x = L are given by V(, t) = V(L,t) x = (2) And the initial conditions V(x, ) = V(x,) t = (3) The foundation reaction PG is given by PG(x, t) = F 2 V(x,t) x 2 + KV(x, t) (4) Where F is the shear modulus and K is the foundation stiffness. Furthermore, the harmonic magnitude moving force P(x,t) acting on the beam is given by P(x, t) = P cos wt f(x Vt) (5) Where w is the load natural frequency and f(*) is the dirac-delta function. When equations (4) and (5) are substituted into (1), the result is a nonhomogeneous system of partial differential equations given by EI 4 V(x,t) + μ 2 V(x,t) N 2 V(x,t) 2 μr 4 V(x,t) v(x,t) x 4 x 2 x 2 + Σ + F 2 V(x,t) + x 2 t 2 t x 2 KV(x, t) = P cos wt f(x Vt) (6) 3. Approximate Analytical Solution The effective applicable method of handling 6 is the integral transform technique, specifically, the Fourier transformation for the length coordinates and the Laplace transformation for the time coordinate with boundary and initial conditions are used

786 A. Jimoh and E. O. Ajoge in this work. The finite Fourier sine integral transformation for the length coordinate is defined as L V(m, t) = V(x, t) sin mux L (7) With the inverse transform defined as V(x, t) = 2 L n=1 V(m, t) sin mux L (8) Thus, by invoking equation (7) on equation (6), we have K m (1 + R 2 π 2 ) V tt(m, t) + V t (m,t) μ ) V(m, t) = P μ L 2 cos wt sin mπvt L μ + ( EI μ (mπ L )4 + N μ (mπ L )2 F μ (mπ L )2 + (9) Equation (9) can be conveniently be written as: V tt (m, t) + 11 V t (m, t) + 12 V(m, t) = 13 cos wt sin t (1) Where b = 1 + R ( mπ L )2, b 1 = Σ, μ K b 2 = EI μ (mπ L )4, b 3 = 1 μ (mπ L )2 (N F), b 4 =, b μ 5 = P, P = mg (11) μ 11 = b 1 b, 12 = b 2 + b 3 + b 4 b, 13 = b 5 b, = mπv L Equation (1) represent the first Fourier transformed governing equations of the uniform Rayleigh beam subjected to harmonic magnitude moving load moving with constant velocity 3.1 Laplace Transformed Solutioins To solve equation (1) above, we apply the method of the Laplace integral transformation for the time coordinate between and. The operation of the Laplace transform is indicated by the notation. L(f(t)) = f(t) e st dt (12) Here

Effect of rotatory inertia and load natural frequency 787 L and s are the Laplace transform operator and Laplace transform variable respectively. In particular, we use L(V(m, t)) = V(m, s) = V(m, t) e st dt (13) Using the transformation in equation (13) on equation (1) in conjunction with the set of the initial conditions in equation (3) and upon simplification we obtain V(m, s) = 13 2(c 1 c 2 ) (( 1 s c 1 ) ( s 2 2) ( 1 s c 2 ) ( s 2 2) ( 1 s c 1 ) ( s 2 2) + ( 1 s c 2 ) ( s 2 2)) (14) Where c 1 = 11 + 11 2 4 12 2 2 (15) c 2 = 11 11 2 4 12 2 2 = w + = w (16) In order to obtain the Laplace inversion of equation (14), we shall adopt the following representations F 1 (s) = ( 1 s c 1 ) F 2 (s) = ( 1 s c 2 ) (17) G 1 (s) = ( s 2 2 ) G 2 (s) = ( s 2 2 )

788 A. Jimoh and E. O. Ajoge So that the Laplace inversion of equation (14) is the convolution of f i and g j defined as t f i g j = f i (t u) g j (u)du, i = 1, 2, ; j = 1, 2 Thus the Laplace inversion of (14) is given by z(m, t) = Where 13 2(c 1 c 2 ) (F 1(s)G 1 (s) F 2 (s)g 1 (s) F 1 (s)g 2 (s) + F 2 (s)g 2 (s) t F 1 G 1 = e c1t e c 1u sin u du t F 1 G 2 = e c1t e c 1u t F 2 G 1 = e c2t e c 2u t F 2 G 2 = e c2t e c 2u sin u du sin u du sin u du (18) (2) (21) (22) (23) (19) Evaluating the integrals (2 23) to obtain F 1 (t)g 1 (t) = F 1 (t)g 2 (t) = 2 + c 1 2 (((ec 1t cos t) c 1 sin t)) 2 + c 1 2 (((ec 1t cos t) c 1 sin t)) (24) (25) (26) F 2 (t)g 1 (t) = 2 + c 2 2 (((ec 2t cos t) c 2 sin t)) (27) F 2 (t)g 2 (t) = 2 + c 2 2 (((ec 2t cos t) c 2 sin t)) Putting equations (24-27) to obtain

Effect of rotatory inertia and load natural frequency 789 V(m, t) = 13 2(c 1 c 2 ) ( 2 + c 1 2 (((ec 1t cos t) c 1 sin t))) 2 + c 1 2 (((ec 1t cos t) c 1 sin t)) 2 + c 2 2 (((ec 2t cos t) c 2 sin t)) + 2 + c 2 2 (((ec 2t cos t) c 2 sin t)) (28) The inversion of equation (28) yields V(m, t) = 2 L [ 13 2(c 1 c 2 ) ( 2 1 + c (((ec1t cos t) c 1 sin d 1 t))) 1 n=1 2 + c 1 2 (((ec 1t cos t) c 1 sin t)) 2 + c 2 2 (((ec 2t cos t) c 2 sin t)) + 2 2 + c (((ec2t cos t) c 2 sin d 2 t))] sin mux 2 L (29) Equation (29) represents the transverse displacement response to a harmonic magnitude moving load with constant velocity of uniform Rayleigh beam resting on Pasternak foundation. 4. Numerical Calculations and Discussion of Results In this section, numerical results for the uniform Rayleigh beam are presented in plotted curves. An elastic beam of length 12.9 m is considered. Other values used are modulus of elasticity E =2.1924 x 1 1 N/m 2, the moment of inertial I= 2.87698 x 1-3 m and mass per unit length of the beam μ = 341.563 kg/m. The value of the foundation stiffness (k) is varied between ( & 4) N/m 3, the value of the axial force N is varied between ( & 2. x 1 8 )N, the values of the shear modules (G) varied between ( an3) N/m 3, damping coefficient (Σ) varied between (1.8 & 3.), rotatory inertia R varied between ( & 12), and the value of Natural Frequency of the moving load is between ( & 12), the results are shown in the graphs below, and from the graphs it was observed that an increase in all the structural parameters lead to decreases in the deflection profile of the uniform Rayleigh beam subjected to harmonically varying magnitude moving load. It was also observed that the effect of load natural frequency is more pronounced than that of rotatory inertial.

DISPLACEMENT V(L/2, t) DISPLACEMENT V(L/2, t) 79 A. Jimoh and E. O. Ajoge,12,1,8,6,4,2 RO = RO = 5 RO = 1 -,2 -,4,2,4,6,8 1 1,2 1,4 1,6 1,8 2 TIME t Fig 1: Deflection profile of uniform Rayleigh Beam subjected to harmonically varying moving loads for various values of Rotatory Inertial (R) and fixed values of Shear Modulus (G), Foundation Modulus (K), Damping Coefficient (Ƹ), Axial Force (N), and Load Natural Frequency (w).,12,1,8,6,4,2 W = W =.5 W = 1. -,2 -,4,2,4,6,8 1 1,2 1,4 1,6 1,8 2 TIME t Fig 2: Deflection profile of uniform Rayleigh Beam subjected to harmonically varying moving loads for various values of Load Natural Frequency (w) and fixed values of Shear Modulus (G), Foundation Modulus (K), Damping Coefficient (Ƹ), Axial Force (N), and Rotatory Inertial (R).

DISPLACEMENT V(L/2, t) DISPLACEMENT V(L/2, t) Effect of rotatory inertia and load natural frequency 791,12,1,8,6,4,2 N = N = 2 N = 2 -,2 -,4,2,4,6,8 1 1,2 1,4 1,6 1,8 2 TIME t Fig 3: Deflection profile of uniform Rayleigh Beam subjected to harmonically varying moving loads for various values of Axial Force (N) and fixed values of Shear Modulus (G), Foundation Modulus (K), Damping Coefficient (Ƹ), Rotatory Inertial (R), and Load Natural Frequency (w).,12,1,8,6,4,2 K = K = 4 K = 4 -,2 -,4,2,4,6,8 1 1,2 1,4 1,6 1,8 2 TIME t Fig 4: Deflection profile of uniform Rayleigh Beam subjected to harmonically varying moving loads for various values of Foundation Modulus (K) and fixed values of Shear Modulus (G), Damping Coefficient (Ƹ), Rotatory Inertial (R), Load Natural Frequency (w), and Axial Force (N).

DISPLACEMENT V(L/2, t) DISPLACEMENT V(L/2, t) 792 A. Jimoh and E. O. Ajoge,16,14,12,1,8,6,4 ε = 1.8 ε = 2.3 ε = 2.8,2,2,4,6,8 1 1,2 1,4 1,6 1,8 2 TIME t Fig 5: Deflection profile of uniform Rayleigh Beam subjected to harmonically varying moving loads for various values of Damping Coefficient (Ƹ) and fixed values of Shear Modulus (G), Rotatory Inertial (R), Load Natural Frequency (w), Axial Force (N), and Foundation Modulus (K).,4,35,3,25,2,15,1,5 G = G = 9 G = 12 -,5 -,1,2,4,6,8 1 1,2 1,4 1,6 1,8 2 TIME t Fig 6: Deflection profile of uniform Rayleigh Beam subjected to harmonically varying moving loads for various values of Shear Modulus (G) and fixed values of Shear Modulus (G), Rotatory Inertial (R), Load Natural Frequency (w), Axial Force (N), Foundation Modulus (K), and Damping Coefficient (Ƹ).

Effect of rotatory inertia and load natural frequency 793 5. Conclusion In this paper, the problem of the dynamic response to harmonic magnitude moving load of uniform Rayleigh beam resting on Pasternak foundation is investigated. The approximation technique is based on the finite Fourier sine transform, Laplace transformation and convolution theorem. Analytical solutions and numerical analysis show that load natural frequency and rotatory inertia decreases the deflection profile of beam subjected to harmonic magnitude moving load. Furthermore, increases in other structural parameter such as shear modulus foundation stiffness, axial force and damping coefficient decreases the response amplitude of the beam. Finally, it was observed that rotatory inertia had more noticeable effect than that of the load natural frequency. References [1] R. S. Ayre, L. S. Jacobsen and C. S. Hsu, Transverse vibration of one and of two-span beams under the action of a moving mass load, Proceedings of the first U.S National Congress of Applied Mechanics, (1951), 81-9. [2] J. Kenny, Steady state vibrations of a beam on an elastic foundation for a moving load, J. Appl. Mech., 76 (1984), 359-364. [3] C. R. Steel, Beams and shells with moving loads, Int. Journal of Solids and Structures, 7 (1971), 1171-1198. https://doi.org/1.116/2-7683(71)96-6 [4] S. T. Oni, On the thick beams under the action of a variable traveling transverse load. Abacus, Journal of Mathematical Association of Nigeria, 25 (1997), no. 2, 531-546. [5] T. P. Chang and H. W. Liu, Vibration analysis of a uniform beam traversed by a moving vehicle with random mass and random velocity, Structural Engineering & Mechanics, An International Journal, 31 (29), no. 6, 737-749. https://doi.org/1.12989/sem.29.31.6.737 [6] S. T. Oni and B. Omolofe, Vibration analysis of non-prismatic beam resting on elastic subgrade and under the actions of accelerating masses, Journal of the Nigerian Mathematical Society, 3 (211), 63-19. [7] S. T. Oni and T. O. Awodola, Dynamic behaviour under moving concentrated masses of simply supported rectangular plates resting on variable winkler elastic foundation, Latin American Journal of Solids and Structures, 8 (211), 373 392. https://doi.org/1.159/s1679-782521141

794 A. Jimoh and E. O. Ajoge [8] R. K. Misra, Free Vibration analysis of isotropic plate using multiquadric radial basis function, International Journal of Science, Environment and Technology, 1 (212), no. 2, 99 17. [9] S. T. Oni and S.N. Ogunyebi, Dynamical analysis of a prestressed elastic beam with general boundary conditions under the action of uniform distributed masses, Journal of the Nigerian Association of Mathematical Physics, 12 (28), 87-12. https://doi.org/1.4314/jonamp.v12i1.45492 [1] M. H. Hsu, Vibration characteristics of rectangular plates resting on elastic foundations and carrying any number of spring masses, International of Applied Sciences and Engineering, 4 (26), no. 1, 83-89. [11] K. Achawakorn and T. Jearipongkul, Vibration analysis of Exponential cross-section beam of exponential cross-section beam using Galerkin s method, International Journal of Applied Science and Technology, 2 (212), no. 6, 7-13. [12] A. D. Kerr, Elastic and Viscoelastic foundation models, Journal of Applied Mechanics, 31 (1964), 491-499. https://doi.org/1.1115/1.3629667 [13] G. L. Anderson, The influence of a Weghardt type elastic foundation on the stability of some beams subjected to distributed tangential forces, Journal of Sound and Vibration, 44 (1976), no, 1, 13-118. https://doi.org/1.116/22-46x(76)971- [14] P. L. Pasternak, On a new method of analysis of an elastic foundation by means of two foundation constants in (Russian). Gosudertrennve itdate Ustre Literature, Postroetalstivvi Arkhiteektre, Moscow. [15] I. Coskum, The response of a finite beam on a tensionless Pasternak foundation subjected to a harmonic load, Eur. J. Mech. A- Solide, 22 (23), no. 1, 151-161. https://doi.org/1.116/s997-7538(3)11-1 [16] S. T. Oni and A. Jimoh, On the dynamic response to moving concentrated loads of non-uniform Bernoulli-Euler Beam resting on Bi-parametric subgrades with other boundary conditions, A Journal of National Mathematical Sciences, 3 (214), no. 1, 515-538. [17] K. Guter, Circular elastic plate resting on tensionless Pasternak foundation, J. Eng. Mech., 13 (23), no. 1, 1251-1254. https://doi.org/1.161/(asce)733-9399(24)13:1(1251) [18] S. T. Oni and A. Jimoh, Dynamic response to moving concentrated loads of simply supported pre-stressed Bernoulli-Euler beam resting on Bi- parametric

Effect of rotatory inertia and load natural frequency 795 subgrades, International Journal of Scientific and Engineering Research, 7 (216), no. 9, 584-6. [19] S. T. Oni and A. Jimoh, On the dynamic response to moving concentraed loads of pre-stressed Bernoulli-Euler subgrades with other boundary conditions, A Journal of National Mathematical Centre, Abuja, 4 no 1, 857-88. [2] X. Ma, I. W. Butterworth and G. C. Cliffon, Static analysis of an infinite beam resting on a tensionless Pasternak foundation, Eur. J. Mech. A. Solid, 28 (29), 697-73. https://doi.org/1.116/j.euromechsol.29.3.3 [21] S. T. Oni and A. Jimoh, Dynamic response to moving concentrated loads of non-uniform simply supported pre-stressed Bernoulli-Euler beam resting on bi-parametric subgrades, International Journal of Scientific and Engineering Research, 7 (216), no. 3, 754-77. [22] L. Fryba, Vibration of Solids and Structures Under Moving Loads, Springer, Gronigen, Noordhoff, 1972. https://doi.org/1.17/978-94-11-9685-7 Received: March 21, 218; Published: July 6, 218