SYSTEM SOLUTION KITS Supplementary price list Great Britain Effective 1 January 2018 2018
System Solution Kits With over 10,000 products combining as systems and solutions to common problems associated with tile and stone installations, we recognise that finding the right combinations for crack-free coverings, guaranteed waterproofing, and underfloor heating is not always easy. At Schlüter-Systems Ltd, it is one of our aims to make life easier - our System Solution Kits have been introduced for this very reason, enabling all of the necessary products to be easily selected and available in a single box. This not only saves time, but also ensures that you have all of the right products and therefore the complete solution for the job. The kits contain all of the required components to create perfectly prepared: Floors that are protected with Schlüter -DITRA 25 matting for uncoupling and crack-bridging, with all joints sealed with the Schlüter -KERDI range for CE marked waterproofing Walls that are waterproofed with the Schlüter -KERDI range for CE marked waterproofing Floors or walls that are heated with Schlüter -DITRA-HEAT Drainage with the choice of point drains from Schlüter -KERDI-DRAIN, linear drains from Schlüter -KERDI-LINE and CE marked waterproofing for wetrooms and showers with the Schlüter -KERDI range Our solutions aren t limited to being covered in beautiful tiles and stone; the Schlüter -LIPROTEC kits allow details and features to be elegantly illuminated, including walls, mirrors, baths, edges and steps to enhance the beauty of a room. However, should these kits not fit your project requirements, then a solution can be found in our Profile and Systems price list.
UNDERFLOOR HEATING Schlüter -DITRA-HEAT-E UNDER TILE AND STONE HEATING FOR FLOORS AND WALLS Schlüter -DITRA-HEAT-E is a system for electrical under floor and wall heating that creates comfortably warm tile and stone coverings. The heating cables of Schlüter -DITRA-HEAT-E are installed in the uncoupling mat for targeted heating of the corresponding tiled areas. With the flexible control of temperatures and heating times provided by our programmable intelligent thermostat, you can use Schlüter -DITRA-HEAT-E to create warm tiles whenever and wherever you choose. 13dB Reduction 13dB Reduction 13dB Reduction 13dB Reduction 13dB Reduction From 5.5mm 13dB Reduction 13dB Reduction Uncoupling Surface Heating Impact Sound Reduction Thermal Break Load Distribution Crack-Bridging Waterproofing Vapour Management
UNDERFLOOR HEATING Schlüter -DITRA-HEAT-E-S Complete floor heating kits Schlüter -DITRA-HEAT-E-S floor kits are complete sets for electrical underfloor heating. They include the uncoupling mats Schlüter -DITRA-HEAT-MA, the heating cables Schlüter -DITRA-HEAT-E-HK and the thermostat set Schlüter -DITRA-HEAT-E-R. If needed, the uncoupled area can be extended with additional Schlüter -DITRA-HEAT-MA uncoupling mats. (Product data sheet 6.4) Schlüter -DITRA-HEAT-E-S Floor Kits complete electrical floor heating system 5.5 mm Uncoupled area (m 2 ) Heated area (m 2 ) at 136 W/m 2 / Set PL = Set 1.6 1.1 DH S16 S2 337.31 9 2.4 1.6 DH S24 S2 376.12 9 3.2 2.2 DH S32 S2 407.33 9 4.0 2.7 DH S40 S2 454.79 8 4.8 3.3 DH S48 S2 500.51 8 5.6 3.8 DH S56 S2 543.11 5 6.4 4.4 DH S64 S2 596.12 5 7.2 5.0 DH S72 S2 650.49 4 8.0 5.5 DH S80 S2 674.20 4 Content: Schlüter -DITRA-HEAT-MA uncoupling mats Schlüter -DITRA-HEAT-E-HK heating cables Schlüter -DITRA-HEAT-E-R thermostat set 4 Prices exclude VAT
UNDERFLOOR HEATING Schlüter -DITRA-HEAT-E-DUO-S Complete floor heating kits with integrated thermal break and acoustic reduction fleece Schlüter -DITRA-HEAT-E-DUO-S floor kits are complete sets for electrical underfloor heating. They include the uncoupling mats Schlüter -DITRA-HEAT-DUO, the heating cables Schlüter -DITRA-HEAT-E-HK and the thermostat set Schlüter -DITRA-HEAT-E-R. If needed, the uncoupled area can be extended with additional Schlüter -DITRA-HEAT-DUO uncoupling mats. The special Schlüter - DITRA-HEAT-DUO thermal break, in addition to reducing impact sound by up to 13dB enables significantly faster response. (Product data sheet 6.4) Schlüter -DITRA-HEAT-E-DUO-S Floor Kits complete floor heating system with integrated thermal break and acoustic reduction fleece 5.5 mm 2 mm Uncoupled area (m 2 ) Heated area (m 2 ) at 136 W/m 2 / Set PL = Set 1.6 1.1 DH D S1 362.38 9 2.4 1.6 DH D S2 402.65 9 3.2 2.2 DH D S3 435.42 9 4.0 2.7 DH D S4 482.24 8 4.8 3.3 DH D S5 529.06 8 5.6 3.8 DH D S6 582.43 5 6.4 4.4 DH D S7 629.25 5 7.2 5.0 DH D S8 685.44 4 8.0 5.5 DH D S9 725.70 4 Content: Schlüter -DITRA-HEAT-DUO uncoupling mats Schlüter -DITRA-HEAT-E-HK heating cables Schlüter -DITRA-HEAT-E-R thermostat set Prices exclude VAT 5
UNDER WALL HEATING Schlüter -DITRA-HEAT-E-WS Complete wall heating kits Schlüter -DITRA-HEAT-E-WS wall kits are complete sets for electrical under wall heating. They include the uncoupling mats Schlüter -DITRA-HEAT-MA, the heating cables Schlüter -DITRA-HEAT-E-HK and the thermostat set Schlüter -DITRA-HEAT-E-R. If needed, the uncoupled area can be extended with additional Schlüter -DITRA-HEAT-MA uncoupling mats. (Product data sheet 6.4) Schlüter -DITRA-HEAT-E-WS Wall Kits complete electrical wall heating system Uncoupled area (m 2 ) Heated area (m 2 ) at 200 W/m 2 / Set PL = Set 3.2 2.6 DH WS1 515.01 9 2.4 1.8 DH WS2 435.42 9 Schlüter -DITRA-HEAT-E-DUO-WS Complete wall heating kits with integrated thermal break and acoustic reduction fleece Schlüter -DITRA-HEAT-E-DUO-S wall kits are complete sets for electrical under wall heating. They include the uncoupling mats Schlüter -DITRA-HEAT-DUO, the heating cables Schlüter -DITRA-HEAT-E-HK and the thermostat set Schlüter -DITRA-HEAT-E-R. If needed, the uncoupled area can be extended with additional Schlüter -DITRA-HEAT-DUO uncoupling mats. The special Schlüter - DITRA-HEAT-DUO thermal break, in addition to reducing impact sound by up to 13dB, enables significantly faster heating response. (Product data sheet 6.4) Schlüter -DITRA-HEAT-E-DUO-WS Wall Kits* complete electrical wall heating system with integrated thermal break Uncoupled area (m 2 ) Content: Heated area (m 2 ) at 200 W/m 2 / Set PL = Set 3.2 2.6 DH D S10 526.72 9 2.4 1.8 DH D S11 444.22 9 Schlüter -DITRA-HEAT-MA\ *Schlüter -DITRA-HEAT-DUO uncoupling mats Schlüter -DITRA-HEAT-E-HK heating cables Schlüter -DITRA-HEAT-E-R thermostat set 6 Prices exclude VAT
WETROOMS Schlüter -WETROOMS INTEGRATED WETROOM KITS For peace of mind when it comes to long term success, possible time and cost savings and versatile design options, we recommend an integrated single-source system. The beauty of the Schlüter -WETROOM system is that its products have been designed and manufactured to complement each other and take care of installation issues, resulting in a reliable, water-tight finish which is CE marked and guaranteed to last for years to come. Incorporating the very latest innovations for floor-level access showers and wetrooms, Schlüter-Systems provides a fully integrated product suite, including top of the range ready-to-tile pre-sloped shower trays, drainage systems and waterproofing membranes for walls and floors. Prices exclude VAT 7
WETROOMS Schlüter -KERDI-DRAIN-WRKD Integrated point drain wetroom kit Schlüter -KERDI-DRAIN-WRKD is an integrated wetroom kit with a point drain set. A collar made of Schlüter -KERDI is provided so a reliable connection of the channel body to the bonded waterproofing assembly can be ensured. The kit also includes a Schlüter - KERDI-SHOWER-SK waterproofing kit, preformed shower tray and a frameless design grate for subtle integration with your chosen tile or stone covering. Schlüter -KERDI-DRAIN-H Integrated Wetroom Kit complete wetroom kit with horizontal exit and Schlüter -KERDI-DRAIN point drain L x W = cm (Tray) H = mm (Tray) / Set PL = Set 100 x 100 22 WRK 1000 KD H50 ED4 364.33 3 Schlüter -KERDI-DRAIN-V Integrated Wetroom Kit complete wetroom kit with vertical exit and Schlüter -KERDI-DRAIN point drain WRK 1000 KD H50 ED4 includes: L x W = cm (Tray) H = mm (Tray) / Set PL = Set 100 x 100 22 WRK 1000 KD V50 ED4 344.33 3 Schlüter -KERDI-SHOWER- SK (KSS5) waterproofing kit WRK 1000 KD V50 ED4 includes: Schlüter -KERDI- SHOWER-TB Schlüter -KERDI-DRAIN design 4 tile support grate and frame Schlüter -KERDI-DRAIN horizontal drain and odour trap Schlüter -KERDI-SHOWER- SK (KSS5) waterproofing kit Schlüter -KERDI- SHOWER-TB Schlüter -KERDI-DRAIN design 4 tile support grate and frame Schlüter -KERDI-DRAIN vertical drain and odour trap 8 Prices exclude VAT
WETROOMS Schlüter -KERDI-LINE-WRKL Integrated linear drain wetroom kit Schlüter -KERDI-LINE-WRKL is an integrated wetroom kit with a linear drain set. The linear drain set can be positioned centrally, off-set, or at the perimeter of the shower area. A collar made of Schlüter -KERDI is pre-adhered to the flange on the surround of the channel body, and ensures the reliable connection of the channel body to the bonded waterproofing assembly. The kit includes a waterproofing and sealing kit, drain body and a frameless design grate for subtle integration with your chosen tile or stone covering. The enclosed shower tray can be cut down to size to accommodate drain position. Schlüter -KERDI-LINE-H 50 Integrated Wetroom Kit complete wetroom kit with horizontal exit DN50 and Schlüter -KERDI-LINE linear drain L x W = cm (Tray) 100 x 100 / 150 x 100 H = mm (Tray) L = cm (Drain\Grate) / Set PL = Set 42 60 WRK 1000 KL H50 DE60 788.72 3 42 70 WRK 1000 KL H50 DE70 803.48 3 42 80 WRK 1000 KL H50 DE80 812.94 3 All kits include: Schlüter -KERDI-SHOWER- SK (KSS10) waterproofing and sealing kit Schlüter -KERDI-SHOWER-LS (KSL1000S) and half a Schlüter -KERDI-SHOWER-L (KSL1000) for perimeter, intermediate or off-set installation. Schlüter -KERDI-LINE-D tile support grate to fit the drainage channel length. Schlüter -KERDI-LINE-H 50 G2 linear horizontal drainage channel, and low height channel support Prices exclude VAT 9
UNCOUPLING AND WATERPROOFING Schlüter -SYSTEMS UNCOUPLING AND WATERPROOFING To ensure peace of mind for a fully watertight installation, a waterproof membrane should be used on the floor and walls. For walls, Schlüter - KERDI-200 provides a CE marked waterproofing membrane for tile and stone coverings, that is easy to install and fully waterproof when sealed with Schlüter -KERDI-KEBA sealing band and Schlüter -KERDI-COLL-L sealing adhesive. For floors, use waterproof uncoupling layer Schlüter -DITRA 25 to prevent stresses from the substrate being transferred to the surface covering, protect moisture sensitive substrates and neutralise vapour pressure by allowing moisture in the substrate to evaporate. The floor should be sealed at the matting joints and the floor-to-wall junctions including internal and external corners with Schlüter -KERDI-KEBA sealing band and Schlüter -KERDI-COLL-L sealing adhesive. 10 Prices exclude VAT
UNCOUPLING AND WATERPROOFING Schlüter -DITRA Kit Uncoupling and waterproofing kit for floors Schlüter -DITRA Kit is a complete uncoupling and waterproofing system for floors, suitable for use in areas such as wetrooms, bathrooms and kitchens with tile and stone coverings. It includes Schlüter -DITRA 25 uncoupling matting, Schlüter -KERDI-KEBA sealing band and Schlüter -KERDI-KERECK prefabricated corner pieces for waterproofing the abutting joints of the matting, corners and floorto-wall transitions. The kit also includes Schlüter -KERDI-COLL-L sealing adhesive for waterproofing the sealing band and prefabricated parts. Schlüter -DITRA Kit complete uncoupling and waterproofing kit for floors Area (m 2 )* / Set PL = Set 5 SSL UK 5M 140.04 15 Kit includes: Schlüter -DITRA 25 uncoupling matting Size: 1 m x 5 m Schlüter -KERDI-KEBA sealing band Size: 15 cm x 5 m Schlüter -KERDI-COLL-L sealing adhesive Tub size: 1.85 kg Schlüter -KERDI-KERECK prefabricated corners Quantity: 2 *For additional waterproofing materials, see page 13. Prices exclude VAT 11
WATERPROOFING Schlüter -KERDI Kit Waterproofing kit for walls Schlüter -KERDI Kit is a complete waterproofing system for walls, suitable for use in areas such as wetrooms and bathrooms with tile and stone coverings. It includes Schlüter -KERDI-200 waterproofing membrane, Schlüter -KERDI-KEBA sealing band and Schlüter -KERDI-COLL-L sealing adhesive for waterproofing the abutting joints of the membranes and floor-to-wall transitions. Schlüter -KERDI Kit complete waterproofing kit for walls Area (m 2 )* / Set PL = Set 5 SSL WK 5M 140.79 15 Kit includes: Schlüter -KERDI-200 waterproofing membrane Size: 1 m x 5 m Schlüter -KERDI-KEBA sealing band Size: 12.5 cm x 5 m Schlüter -KERDI-COLL-L sealing adhesive Tube size: 1.85 kg Schlüter -KERDI-KERECK prefabricated corners Quantity: 2 *For additional waterproofing materials, see page 13. Schlüter -KERDI-COLL-L Schlüter -KERDI-COLL-L is a two component sealant adhesive based on a solvent free acrylate dispersion and a reactive cementitious powder. It is suitable for adhering and sealing overlaps of Schlüter - KERDI membranes. In addition, Schlüter - KERDI-COLL-L can be used to tightly adhere the sealing band Schlüter -KERDI-KEBA on bonded waterproofing assemblies. Schlüter - KERDI-COLL-L has an extended curing time to facilitate installation in environments with higher temperatures. (Product data sheet 8.4) Schlüter -KERDI-COLL-L two component sealing adhesive Weight kg / kg PL = 1.85 KERDI-COLL-L 185 9.80 110 4.25 KERDI-COLL-L 8.06 75 Note: Installation time at 20/30 C approx. 90/60 min. Hardening times are significantly longer in cool ambient temperatures. 12 Prices exclude VAT
WATERPROOFING Schlüter -KERDI-KERECK-F Schlüter -KERDI-KERECK-F are completely seam sealed, prefabricated parts to produce internal and external corners. (Product data sheet 8.1) Schlüter -KERDI-KERECK/FA 90 external corner, prefabricated H = mm Set = 2 units / Set P = Set 0.1 KERECK/FA2 16.87 10 Schlüter -KERDI-KERECK/FI 90 internal corner, prefabricated H = mm Set = 2 units / Set P = Set 0.1 KERECK/FI2 14.41 10 Schlüter -KERDI-KEBA Schlüter -KERDI-KEBA is a sealing band to seal mat connections and wall to floor connections. (Product data sheet 8.1) Schlüter -KERDI-KEBA/5M sealing band B = mm Roll = 5 m / m PL = Roll 125 KEBA 100 / 125 / 5M 3.77 10 150 KEBA 100 / 150 / 5M 4.03 10 Schlüter -KERDI-TS Schlüter -KERDI-TS is a set for the reliable waterproof connection of building components such as bathtubs and shower trays made of steel enamel, acrylic or mineral casting to the Schlüter -KERDI waterproofing system. It includes a sealing tape made of polyethylene with double-sided fleece fabric and selfadhesive sound insulation strip, Schlüter - KERDI-FIX installation adhesive, cleaning cloths as well as installation corner piece(s). (Product data sheet 8.9) 5 mm 3 22 100 mm Schlüter -KERDI-TS complete set for waterproof connection L = m / Set PL = 2 KE TS / 200 63.25 10 2.8 KE TS / 280 76.44 10 3.8 KE TS / 380 90.09 10 Note: The sets KETS/280 and KETS/380 each contain 2 installation corner pieces. Prices exclude VAT 13
WATERPROOFING Schlüter -KERDI-TS-ZC Schlüter -KERDI-TS-ZC is an expansion set for the reliable waterproof connection of building components such as bathtubs and shower trays for special installation situations (see drawing) in connection with the Schlüter -KERDI-TS waterproofing set. It consists of a waterproofing collar and a corner installation piece. (Product data sheet 8.9) Schlüter -KERDI-TS-ZC expansion set / Set PL = KE TS ZC 9.05 10 Schlüter -KERDI-FIX The expansion set comprises the following components: 1 PE collar, fleece-laminated on both sides, 120x120mm 1 corner installation piece installation examples Schlüter -KERDI-CP Schlüter -KERDI-CP is a cutting protection that can be shortened to any length and protects the connection seal when the silicone joint is renovated at a later time. The versatile folding profile can be installed directly in the adhesive bed or into freshly applied Schlüter - KERDI-FIX. (Product data sheet 8.9) 5 mm 15 mm 5 mm 0,8 Schlüter -KERDI-CP polypropylene cutting protection L = m / U. PL = 2 KE CP / 200 7.23 10 2.8 KE CP / 280 10.01 10 3.8 KE CP / 380 13.20 10 10 KE CP / 1000 29.12 10 Schlüter -DILEX-AS Schlüter -DILEX-AS is a joining profile for creating flexible joints to fixtures such as shower trays, baths, door and window frames. (Product data sheet 4.10) 29 mm 9 20 mm Schlüter -DILEX-AS PVC L = 2.50 m / U. KV = AS 20 BW 7.05 90 Schlüter -DILEX-AS/I 90 internal corner / U. P = I / AS 20 BW 1.07 10 Schlüter -DILEX-AS/EK end cap Set = 1 x left, 1 x right / Set KV = AS 20 BW 2.14 10 14 Prices exclude VAT
WETROOM ACCESSORIES Schlüter -KERDI-BOARD-N PREFABRICATED NICHES There are a variety of ways to enhance the look and functionality of a wetroom, bathroom or en-suite and one of the easiest ways is to create integrated tiled shelving. Schlüter -KERDI-BOARD-N is a range of prefabricated niches that are fully sealed, quick to install, and integrated with the rest of the Schlüter -KERDI-BOARD range. The larger niche sizes include a shelf insert that can be installed at any height to create separate compartments within the niche. The main benefit of using a prefabricated niche is that it is waterproof, vapour-tight and features sealed corners for effective waterproofing, saving valuable time during installation. Prices exclude VAT 15
WETROOM ACCESSORIES Schlüter -KERDI-BOARD-N Prefabricated niches Schlüter -KERDI-BOARD-N is a range of prefabricated niches for shelving made of Schlüter -KERDI-BOARD that can be installed in both Schlüter -KERDI and Schlüter -KERDI- BOARD wall assemblies. All niches include a pre-cut collar to make sealing simple. Available in 4 sizes. Schlüter -KERDI-BOARD-N prefabricated niche L x H x D = mm Shelf / U PL = Set 305 x 152 x 89 - KB 12 N 305 152 A 47.51 56 305 x 305 x 89 - KB 12 N 305 305 A 59.45 34 305 x 508 x 89 1 KB 12 N 305 508 A1 87.88 25 305 x 711 x 89 1 KB 12 N 305 711 A1 118.91 16 Product range: KB 12 N 305 152 A KB 12 N 305 305 A KB 12 N 305 508 A1 KB 12 N 305 711 A1 16 Prices exclude VAT 16
WETROOM ACCESSORIES Schlüter -KERDI-DRAIN and Schlüter -SHOWERPROFILE DESIGNER GRATES AND SLOPED PROFILES Elegance in design is about the finer details and subtle finishes that blend in with surroundings, or alternatively, that create a contrast to generate emphasis with sleek, contemporary metal finishes find your perfect style with Schlüter -SYSTEMS. Prices exclude VAT 17
WETROOM ACCESSORIES Schlüter -KERDI-DRAIN Shower grates Schlüter -KERDI-DRAIN grates are a range of designer metal grates and frames, available as alternatives to the support grate included in the Schlüter -KERDI-DRAIN-WRKD Wetroom Kits. Schlüter -KERDI-DRAIN Grate design 1, grate and frame set H = mm / U. 10 x 10 KD R10 ED1 S 46.28 Schlüter -KERDI-DRAIN Grate design 2, grate and frame set H = mm / U. 10 x 10 KD R10 ED2 84.14 Schlüter -KERDI-DRAIN Grate design 3, grate and frame set H = mm / U. 10 x 10 KD R10 ED3 84.14 Schlüter -KERDI-DRAIN-STYLE FLORAL design, grate and frame set H = mm / U. 10 x 10 KD IF 10EB D5 81.45 Schlüter -KERDI-DRAIN-STYLE CURVE design, grate and frame set H = mm / U. 10 x 10 KD IF 10EB D6 81.45 Schlüter -KERDI-DRAIN-STYLE PURE design, grate and frame set H = mm / U. 10 x 10 KD IF 10EB D7 83.27 18 Prices exclude VAT
WETROOM ACCESSORIES Schlüter -SHOWERPROFILE-S Sloped profile for Schlüter -KERDI-LINE Schlüter -SHOWERPROFILE-S is a triangular profile made of a brushed stainless steel flat profile with a 2% slope for covering the sloped edges of floor-level showers. A fleece fabric is laminated on the reverse of the profile for bonding with the tile adhesive. A matching hard PVC support profile is available in different heights and features a U-shaped installation channel. The triangular profile can be shortened as necessary on the short and/or long side to accommodate height adjustment. The triangular profile can be used on the left or right side of the floor transition or below the tiles of a lateral wall. (Product data sheet 14.1) Schlüter -SHOWERPROFILE-SPS 50 PVC tapered support profile, brushed stainless steel V4A, H1 = 6 mm H = mm L = 1.20 m / U. KV = 5 SPSA 50 EB/120 43.43 40 Schlüter -SHOWERPROFILE-SPS 100 PVC tapered support profile, brushed stainless steel V4A, H1 = 10 mm H = mm L = 1.20 m / U. KV = 10 SPSB 100 EB/120 42.39 40 Schlüter -SHOWERPROFILE-SPS 125 PVC tapered support profile, brushed stainless steel V4A, H1 = 10 mm H = mm L = 1.20 m / U. KV = 12.5 SPSB 125 EB/120 42.39 40 SPS 50 SPS 100 SPS 125 H = 5 mm H = height of support profile SPS 50 is suitable for tile thickness of 6-9 mm H = height of support profile SPS 100 is suitable for tile thickness of 10-18 mm H = height of support profile SPS 125 is suitable for tile thickness of 12.5-20 mm L = 1.20 m: H2 = 30 mm, H1 = 6 mm L = 1.20 m: H2 = 34 mm, H1 = 10 mm L = 1.20 m: H2 = 34 mm, H1 = 10 mm Schlüter -SHOWERPROFILE-R Schlüter -SHOWERPROFILE-R is a two part wall transition profile for covering the wall area exposed due to the use of a wedge with a line drainage channel. The visible surface of the profile consists of brushed stainless steel. A fleece fabric is laminated the reverse for bonding with the tile adhesive. Due to the two part design, Schlüter -SHOWERPROFILE-R can be seamlessly adjusted to any height between 23 and 45 mm (available in two versions). (Product data sheet 14.1) Schlüter -SHOWERPROFILE-RA two part wall transition profile, brushed stainless steel V4A 20 mm = H H = mm L = 1.00 m / U. KV = 23-35 SPRA 23 EB/100 48.44 40 33-45 SPRA 33 EB/100 53.06 40 22 / 32 mm H = variabel Prices exclude VAT 19
WETROOM ACCESSORIES Schlüter -SHOWERPROFILE-WS Schlüter -SHOWERPROFILE-WS is a two piece profile of anodised aluminium that serves as a splashguard in floor level showers. The support profile is embedded in the tile adhesive during tile installation. It can be fitted with a semi-circular or upright straight lip to protect against splashing. Both variations are suitable for wheelchair use. (Product data sheet 14.2) Schlüter -SHOWERPROFILE-WS support profile anodised aluminium, natural satin L = 1.00 m / m P = SPWS 19 AE / 100 18.31 40 Schlüter -SHOWERPROFILE-WSC semi-circular lip L = 1.00 m / m P = SPWSC 16 GS / 100 9.06 40 Schlüter -SHOWERPROFILE-WSL straight lip L = 1.00 m / m P = SPWSL 30 T / 100 10.92 40 8 8 29 mm 19 mm SHOWERPROFILE-WS + WSC 19 mm SHOWERPROFILE-WS + WSL Schlüter -SHOWERPROFILE-WSK Schlüter -SHOWERPROFILE-WSK is a two piece profile of anodised aluminium that serves as a splashguard in floor level showers. The support profile is adhered to existing coverings. It can be fitted with a semi-circular or upright straight lip to protect against splashing. Both variations are suitable for wheelchair use. (Product data sheet 14.2) Schlüter -SHOWERPROFILE-WSK support profile anodised aluminium, natural satin L = 1.00 m / m P = SPWSK 52 AE / 100 21.30 40 Schlüter -SHOWERPROFILE-WSC semi-circular lip L = 1.00 m / m P = SPWSC 16 GS / 100 9.06 40 Schlüter -SHOWERPROFILE-WSL straight lip L = 1.00 m / m P = SPWSL 30 T / 100 10.92 40 Schlüter -SHOWERPROFILE-WSK/EK end cap 37 mm 8 2.5 8 / U. P = EK / SPWSK 52 AE 2.87 50 52 mm SHOWERPROFILE-WSK + WSLS 52 mm HOWERPROFILE-WSK + WSC SHOWERPROFILE-WSK/EK 20 Prices exclude VAT
EDGE PROFILES FOR FLOOR COVERINGS Schlüter -PROFILES FLOOR AND WALL PROFILES The difference between something good and something great is attention to detail. It s the finer details and finishing touches that are subtly incorporated into a design that make it distinct. When careful consideration has been made to the sanitary-ware, taps, shower, tile or stone covering then why leave profiles to chance when a palette of designs, finishes and materials allow you to select details that blend, or act as elegant accents to your design. With Schlüter -PROFILES there are many ways of perfecting and protecting your tile or stone installation with hundreds of options for finishes, textures, materials and colours. AtlasConcorde Prices exclude VAT 21
EDGE PROFILES FOR FLOOR COVERINGS Schlüter -PROFILES for floors Schlüter -SCHIENE - finishes tiled surfaces and protects the outer edges of ceramic and natural stone floor coverings from mechanical impact. Schlüter -RENO - create a smooth transition between adjoining floor coverings of different heights, protecting the exposed tile edge. Schlüter -SCHIENE Schlüter -SCHIENE-ES Schlüter -SCHIENE-BASIC Schlüter -SCHIENE-V Schlüter -RENO-V Schlüter -RENO-U Schlüter -RENO-RAMP Schlüter -RENO-T Refer to the current Illustrated Pricelist for Profiles and Systems for the complete range of sizes, materials and finishes available. 22 Prices exclude VAT
WALL CORNERS AND EDGE PROFILES Schlüter -PROFILES for Walls The tile profiles of Schlüter -JOLLY, Schlüter -RONDEC, and Schlüter -QUADEC create a highly durable and decorative finishing for wall coverings and skirtings made of tile and natural stone. Thanks to a wide palette of material and colour, there are no limits to creativity. Schlüter-Systems range of finishing profiles for walls includes: Schlüter -RONDEC Schlüter -QUADEC Schlüter -JOLLY Schlüter -DECO Schlüter -DECO-SG Schlüter -INDEC Schlüter -DIADEC Schlüter -DESIGNLINE Schlüter -QUADEC-FS Schlüter -DESIGNBASE Schlüter -FINEC Schlüter -DILEX-AHK Refer to the current Illustrated Pricelist for Profiles and Systems for the complete range of sizes, materials and finishes available. Prices exclude VAT 23
Subject to the Standard Terms and Conditions of Sale of Schlüter-Systems Ltd. All previous price lists lose their validity on the publication of this price list. Errors, changes, and printing mistakes as well as changes necessary in the interest of product innovation or shipping reserved. For reasons of printing, colours shown in this price list may differ from actual product colours. Schlüter-Systems KG Schmölestraße 7 D-58640 Iserlohn Tel.: +49 2371 971-261 Fax: +49 2371 971-112 info@schlueter.de www.schlueter-systems.com Schlüter-Systems Ltd s 3-5 Bardon 22 Beveridge Lane Coalville Leicestershire LE67 1TE Tel.: +44 1530 813396 Fax: +44 1530 813376 technical@schluter.co.uk sales@schluter.co.uk www.schluter.co.uk SSL\IPL\KITS18 edition 01/18