Drilling. What is the Activity?

Drilling What is the Activity? Drilling is a critical activity in mineral exploration. There are several types of drilling. Diamond drilling is the most common type of drilling conducted in Ontario. It produces cylindrical pieces of rock called core. Reverse circulation or rotary drilling produces chips of rock. Overburden drilling is conducted to sample glacial deposits. Augur drilling is used to sample soils for geotechnical purposes. Drilling locations are selected using the results from previous studies, such as: Prospecting Geological mapping Geophysical surveys All drilling activities provide samples from below the surface. This allows for the testing of the properties of the soil and rocks, including mineral and metal content. Diamond drills range in size. There are smaller units called backpack or Winkie drills. One or more individuals can carry these. There are rigs the size of a small house. These rigs are typically mounted on skids or runners. They are dragged through the bush behind bulldozers or timber skidders. Diesel and hydraulic motors power most diamond drills. Diamond drilling uses a hollow bit whose surface contains low quality diamonds. It produces a long cylinder of rock referred to as a core. The core is stored in specially shaped core boxes. A geologist or technician examines the core and makes notes on the physical appearance of the rock. The geologist will also mark sections of the core to be sampled for analysis in a laboratory. The core is cut in half lengthwise to be sampled. One side is shipped to a laboratory and the other is stored as a reference sample. The size of the core and the length of the hole drilled depend on the size of the drill, the type of exploration

program and the mineral(s) being analyzed. A diamond drill hole can range in length from a less than a few meters in length to several thousand meters. The core sizes range from less than 2 cm in diameter up to 15 cm. Footprint on the Land Small areas of land must be cleared to make a drill pad. It must be large enough for safe operation of the drill and bulldozer or skidder. A typical drill pad is 20 to 40 meters in diameter. Hauling the drill rig through the bush also makes a very rough trail. Helicopters are sometimes used, especially in remote areas. The drill rigs are taken apart, flown to the site and reassembled. The drill pad for helicopter supported drilling is typically 40 to 50 meters in diameter. Diamond drilling uses hollow steel pipes called casing to drill through overburden such as loose soils and materials. The casing is anchored into the bedrock. The drilling is done through the casing, which provides a collar for the drill hole, keeping soil and water from running into the hole. Companies often choose to leave the casing pipes in the ground. They must mark the casings so that they are visible in all seasons. Leaving casings in the ground allows companies to use the hole at a later date to deepen the hole or to complete geophysical surveys. Some types of drilling, including diamond drilling, pump water to the drill and down the hole. This cools the bit and clears the hole of the ground-up rock. The water pumps may be placed on the shores of lakes, rivers and streams. The water is pumped though heavy hoses to the drill rig. Sumps may be dug at the drill site and the return water containing the ground up rock directed to the sump where the solids can settle out. In some cases, diamond drilling may take place on lake ice during the winter or from barges during other seasons. Special rules apply to this type of drilling. Drill holes that are drilled in lake bottoms as well as drill holes on land that produce water require cementing of the casing, for safety purposes and to control groundwater flow. Mining Act Requirements Drilling that uses a drill that weighs less than 150 kilograms requires an exploration plan. Drilling that uses a drill that weighs more than 150 kilograms requires an exploration permit.

Ministry of Northern Development and Mines Mineral Development and Lands Branch B002 435 James Street South Thunder Bay, Ontario P7E 6S7 Tel.: (807) 475-1123 Fax: (807) 475-1112 Ministère du Développement du Nord et des Mines Direction de l exploitation des minéraux et de la gestion des terrains miniers Bureau B002 435 James Sud Thunder Bay, Ontario P7E 6S7 Tél.: (807) 475-1123 Téléc.: (807) 475-1112 February 9, 2015 Chief Georjann Morriseau and Council Fort William First Nation 90 Anemki Drive, Suite 200 Thunder Bay, Ontario P7J 1L3 Via email: georjann.morriseau@fwfn.com Dear Chief Morriseau: Re: Exploration Permit Application PR-15-10633, Onion Lake Project Onion Lake Area (G-0747), District of Thunder Bay The Ministry of Northern Development and Mines (MNDM) has received an application from Mars Joseph (the proponent ) for an exploration permit under the Mining Act. The exploration permit application is attached for your review. We have also attached information sheets which provide further details about the types of activities proposed in the permit application. MNDM encourages proponents and aboriginal communities to engage early in the mining sequence, build relationships and, where appropriate, formalize commitments through arrangements. If you have not already been contacted by the proponent, their contact information is set out below. The proponent has already been provided with contact information for your community. Mars Joseph 1100 Memorial Avenue Unit 122 Thunder Bay, Ontario P7B 4A3 Tel: 807-632-2757 E-mail: mars_joseph@shaw.ca Please review the permit application and the information sheets. If you have any comments or concerns about potential adverse effects that the proposed early exploration activities may have on your community s existing or asserted Aboriginal and treaty rights and suggestions on how to reduce or avoid such adverse effects, please contact the Mineral Exploration and Development Consultant identified below and the proponent by March 11, 2015.

- 2 - When satisfied that appropriate consultation has taken place, I will make a decision on the permit application within 50 days after the date of this letter. The process may be subject to a Temporary Hold to provide for sufficient time for appropriate consultation if I find that to be necessary. For more information about early exploration and Aboriginal consultation, please refer to Ministry of Northern Development and Mines (MNDM) policy on Consultation and Arrangements with Aboriginal Communities at Early Exploration, which is available at: http://www.mndm.gov.on.ca/sites/default/files/aboriginal_exploration_consultation_policy.pdf. If you have any questions regarding the contents of this letter or about early exploration and Aboriginal consultation, please do not hesitate to contact Patrick Barnes, Mineral Exploration and Development Consultant in the Thunder Bay office, at 807-475-1583 or by e-mail to patrick.m.barnes@ontario.ca Sincerely, Mike Grant Director of Exploration Enclosures: Permit Application Activity Information Sheets ec: Ian Bannon, FWFN ijb@fwfn.com

Capping and Sealing Drill Holes If the drill hole produces water, or if it encounters underground mine opening or solution cavities, it must be sealed. Seal the drill hole at the surface and into the upper bedrock by grouting the upper 30 metres of bedrock or the entire depth of the hole, whichever is lesser. Provincial Standards for Early Exploration All early exploration activities that require an exploration plan or permit must follow the Provincial Standards for Early Exploration. There are three parts to these Provincial Standards: 1. Rules for carrying out exploration plan activities. 2. Rules for carrying out exploration permit activities. 3. Rules for rehabilitation of exploration plan and exploration permit activities. During drilling programs, the Provincial Standards for Early Exploration must be followed for both an exploration plan and an exploration permit: Marking Drill Holes Where Casings Left Mark all drill hole locations that still have casings with durable reflective markers that are clearly visible in all seasons. Drill Core Store drill core samples more than 30 metres from any permanent water body or waterway. The rehabilitation requirements in the Provincial Standards must be followed. They must be done after the exploration activity is complete, or before the exploration plan or permit expires. Drilling Fluids and Cuttings Contain all drilling fluids, cuttings and mud left on site. Contain them more than 30 metres from any permanent water body or waterway.

Drill Core Drill core left on the exploration site must be cross-piled in an orderly manner. The height must be less than 1.5 metres. The drill core pile must be more than 30 metres from any permanent water body or waterway. For the official and most up to date information on the rules for carrying out these exploration and rehabilitation activities, please refer to: The Mining Act Exploration Plans and Exploration Permits Regulation Provincial Standards for Early Exploration Ministry of Northern Development & Mines Office Contact Numbers Sudbury: (705) 670-5815 Timmins: (705) 235-1625 Thunder Bay: (807) 475-1123