Weather Station P03/3-RS485-GPS with RS485 Interface

Transcription

1 Weather Station P03/3-RS485-GPS with RS485 Interface Technical data and notes for installation Elsner Elektronik GmbH Control and Automation Engineering Herdweg 7 D Gechingen Germany Phone: +49 (0) 70 56/ Fax: +49 (0) 70 56/ info@elsner-elektronik.de

2 Description The P03/3-RS485-GPS Weather Station measures temperature, wind speed and brightness (eastern, sothern and western sun). It recognizes precipitation and receives the international time signal UTC and position coordinates with a GPS receiver. Direction (azimuth) and hight (elevation) of the sun are calculated and output. The weather station sends the currently recorded weather data, date and time once every second. This data flow can be received and analyzed by an end device such as SPS, PC or MC. The P03/3-RS485-GPS has four connections. Data output is at terminals A and B. Terminals 1 and 2 are for the power supply (24 V DC). The connections are not resistant to pole reversal. Connecting them incorrectly will destroy the interface components. Functions: Brightness measurement with three separate sensors for east, south and west. Recognition of twilight/dawn with special filters Wind speed measurement by means of a nonwearing electronic sensor. No damage from storm or hail as with mechanical anemometers Temperature measurement Heated precipitation sensor (1.2 watts): No false reports as a result of fog or dew. Dries quickly after precipitation has stopped Integrated GPS receiver. Output of UTC (universal time coordinated), position (longitude, latitude) and position of the sun (azimuth, elevation) Technical data Housing: Plastic material Colour: White / translucent Mounting: On-wall Protection category: IP 44 Dimensions: approx. 96 x 77 x 118 (W x H x D, mm) Weight: approx. 160 g Ambient temperature: Operation C, Storage C Operating voltage: 24 V DC Current: max. 105 ma, residual ripple 10% Data output: RS485 Heating rain sensor: approx. 1.2 W 2 Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted.

3 Measurement range temperature: Measurement range wind: Measurement range brightness: C Resolution: 0.1 C Accuracy: ±0.5 C at C ±1.5 C at C 0 70 m/s Resolution: <10% of the measured value Accuracy: ± 25% at 0 15 m/s, at an angle of attack of 45, pole mounting lux Resolution: 1 lux at lux 2 lux at lux 63 lux at lux 423 lux at lux Accuracy: ± 35% The following standards were referenced with regard to evaluating electromagnetic compatibility of the product: EN : A11:2002 The product has been tested by an accredited EMC laboratory according to the abovementioned standards. Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted. 3

4 PCB layout Fig. 1 1 Socket for connecting cables to rain sensor in housing cover 2 Socket for connection 1: +24 V DC 2: GND A: Data B: Data 3 GPS reception control LED 4 Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted.

5 Transfer protocol All characters and/or digits are based on the ASCII standard, i.e. every reading processed internally as an integer or float value will always be broken down into and transferred in its individual ASCII format characters. They must then be reassembled in the reverse process by the receiver. Transfer rate: Baud Data bits: 8 Stop bit: 1 Parity: none The checksum is calculated along by the receiver by adding all received bytes up until byte 56 and then compared with the checksum transferred from the P03. Units: Temperatures in degrees Celsius Sun intensity in kilolux Daylight in Lux Wind in metres per second Byte No. Char Description 1 G Start of string 2 + / - Outdoor temperature in C, sign Outdoor temperature in C, tens digit Outdoor temperature in C, units digit 5. Outdoor temperature in C, decimal point Outdoor temperature in C, tenths digit Sun south in klux, tens digit Sun south in klux, units digit Sun west in klux, tens digit Sun west in klux, units digit Sun east in klux, tens digit Sun east in klux, units digit 13 J / N Lux twilight indication Daylight in Lux, hundreds digit Daylight in Lux, tens digit Daylight in Lux, units digit Wind in m/s, tens digit Wind in m/s, units digit 19. Wind in m/s, decimal point Wind in m/s, tenths digit 21 J / N Rain indication 22? / 1 7 UTC weekday (1 = mondy... 7 = sunday? = UTC not OK) Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted. 5

6 Byte No. Char Description UTC date day, tens digit UTC date day, units digit UTC date month, tens digit UTC date month, units digit UTC date year, tens digit UTC date year, units digit UTC time hour, tens digit UTC time hour, units digit UTC time minute, tens digit UTC time minute, units digit UTC time second, tens digit UTC time second, units digit 35 0 / 1 GPS report azimuth/elevation/longitude/latitude (1 = OK, 0 = not OK) Azimuth in, hundreds digit Azimuth in, tens digit Azimuth in, units digit 39. Azimuth in, decimal point Azimuth in, tenths digit 41 + / - Elevation in, sign Elevation in, tens digit Elevation in, units digit 44. Elevation in, decimal point Elevation in, tenths digit 46 O / W Longitude in (O = east, W = west) 47 0 / 1 Longitude in, hundreds digit Longitude in, tens digit Longitude in, units digit 50. Longitude in, decimal point Longitude in, tenths digit 52 N / S Latitude in (N = north, S = south) Latitude in, tens digit Latitude in, units digit 55. Latitude in, decimal point Latitude in, tenths digit Checksum thousands digit Checksum hundreds digit Checksum tens digit Checksum units digit 61 0x03 end identifier 6 Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted.

7 Installation and first use The weather station may only be installed, tested, put into operation and troubleshot by a person qualified to do so. When connecting the weather station, do not connect any live wires (switch off the mains fuse first) and take precautionary measures to prevent them from being accidentally switched back on. Make sure all connections are correct. An incorrect connection could destroy the weather station or any electronic devices connected to it. The weather station must be used for its intended purpose only. Any improper modification or failure to observe the operation instructions will void all guarantees or claims to warranty. When unpacking, check the unit immediately for any mechanical damage. The supplier must be informed immediately of any damage caused during transport. The weather station must not be put into use if damaged. If there is any cause to believe that safe operation is no longer guaranteed, the system must be rendered inoperative and secured against being switched on unintentionally. The weather station may only be operated as a stationary installation; i.e. only when mounted and after all installation and initialization procedures are complete, and only in the environment it is intended for. Elsner Elektronik is not liable for any changes to standards or defaults after publication of the operation instructions. Position Choose an installation position in the building where wind, rain and sun can be measured unhindered by the sensors. The weather station must not be installed underneath any structural parts from which water can still drip onto the rain sensor after it has stopped raining or snowing. The weather station must not be shaded by anything, such as building structures or trees. There must be at least 60 cm of free space underneath the weather station to allow it to measure the wind correctly and to prevent it from being snowed in when it snows. Iron structures or large-surfaces of sheet metal directly behind or near the weather station reduce the reception quality of the integrated GPS receiver. Please take this into account when choosing the installation site. Also, magnetic fields, transmitters and interfering fields from electricity consumers (e.g. fluorescent lamps, neon signs, Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted. 7

8 switched-mode power supplies etc.) can interfere with or even cut out reception of the GPS signal. North Fig. 2 Align the weather station in a southward direction. South Fig. 3 The weather station must be mounted onto a vertical wall (or pole). Fig. 4 The weather station must be mounted horizontally in the lateral direction. Attaching the mount The weather station comes with a combination wall/pole mount. The mount comes adhered by adhesive strips to the rear side of the housing. Fasten the mount vertically onto the wall or pole. 8 Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted.

9 Fig. 5 When wall mounting: flat side on wall, crescentshaped collar upward. Fig. 6 When pole mounting: curved side on pole, collar downward. Fig. 7 An additional, optional accessory available from Elsner Elektronik is an articulated arm for flexible wall, pole or beam mounting of the weather station. View of rear side and drill hole plan Fig. 8a: Drill hole plan Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted. 9

10 Fig. 8b: Dimensions of rear side of housing with bracket. Subject to change for technical enhancement. Preparing the weather station 1 Cover with rain sensor 2 Cover snaps 3 Bottom part of housing Fig Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted.

11 The weather station cover with the rain sensor snaps in on the left and right along the bottom edge (see Fig. 9). Remove the weather station cover. Proceed carefully, so as not to pull off the wire connecting the PCB in the bottom part with the rain sensor in the cover (wire with push-connector). Push the connection cable through the rubber seal on the bottom of the weather station and push the power and bus cables onto their designated terminals. The connection is by typical telephone cable (J-Y(ST)Y ). Mounting the weather station Close the housing by putting the cover back over the bottom part. The cover must snap in on the left and right with a definite click. Fig. 10 Make sure the cover and bottom part are properly snapped together! This picture is looking at the closed weather station from underneath. Fig. 11 Push the housing from above into the fastened mount. The bumps on the mount must snap into the rails in the housing. To remove it, the weather station can be simply pulled upwards out of the mount, against the resistance of the fastening. Notes on installation Do not open the P03 weather station if water (rain) could get in: even a few drops could damage the electronics inside. When mounting, you must take care not to damage the temperature sensor (small PCB on the bottom of the housing). Also, the wire connecting the PCB with the rain sensor must not be pulled off or kinked at the terminal. It will take 30 seconds after applying the power before the wind measurement will be output. Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted. 11

12 Remove all existing protection labels after installation. Maintenance The weather station must be checked for dirt on a regular, twice-yearly basis and cleaned if necessary. A dirty weather station can lead to strange results, such as the wind sensor failing to work, the station constantly announcing rain, or failure to detect sunlight. 12 Weather Station P03/3-RS485-GPS Version: 24 March 2010 Subject to technical alterations. Errors excepted.