TALLER DE HIDROSTÁTICA

Size: px
Start display at page:

Download "TALLER DE HIDROSTÁTICA"

Transcription

1 TALLER DE HIDROSTÁTICA 1) Substance A has a density of 3 g/cm 3 and substance B has a density of 4 g/cm 3. In order to obtain equal masses of these two substances, what must be the ratio of the volume of A to the volume of B? A) V A VB = 1 3 B) V A VB = 4 3 C) V A VB = 3 4 D) V A VB = 3 1 E) V A VB = 3 4 1) 2) A styrofoam sphere of radius R has a density. You now carefully compress the sphere so its radius is R/2. What is the density of the compressed sphere? A) 8 B) 8 C) 2 D) 2 E) 4 2) 3) As shown in the figure, fluid fills a container having several sections. At which of the indicated points is the pressure greatest? 3) A) A B) B C) C D) D E) The pressure is the same at each of the labeled points. 1

2 SHORT ANSWER. Write the word or phrase that best completes each statement or answers the question. 4) A cubical block of stone is lowered at a steady rate into the ocean by a crane, always keeping the top and bottom faces horizontal. Which one of the following graphs best describes the gauge pressure p on the bottom of this block as a function of time t if the block just enters the water at time t = 0 s? 4) 5) A plastic block of dimensions 2.00 cm 3.00 cm 4.00 cm has a mass of 30.0 g. What is its density? 5) A) 1.20 g/cm3 B) 0.80 g/cm3 C) 1.60 g/cm3 D) 1.25 g/cm3 6) A compressed gas with a total mass of 107 kg is stored in a spherical container having a radius of m. What is the density of the compressed gas? A) 110 kg/m3 B) 181 kg/m3 C) 134 kg/m3 D) 161 kg/m3 6) 7) The density of material at the center of a neutron star is approximately kg/m3. What is the mass of a cube of this material that is 1.76 microns on each side. (One micron is equal to m.) A) 5.45 kg B) 6.16 kg C) 4.74 kg D) 6.70 kg 7)

3 8) A round coin has a diameter of mm, a thickness of 1.55 mm, and a mass of 2.50 g. What is its density? A) kg/m 3 B) kg/m 3 C) kg/m 3 D) kg/m 3 E) kg/m 3 9) The Aswan High Dam on the Nile River in Egypt is 111 m high. What is the gauge pressure in the water at the foot of the dam? The density of water is 1000 kg/m 3. A) Pa B) Pa C) Pa D) Pa E) Pa 10) The deepest point of the Pacific Ocean is 11,033 m, in the Mariana Trench. What is the gauge pressure in the water at that point? The density of seawater is 1025 kg/m 3. A) Pa B) Pa C) Pa D) Pa E) Pa 11) A circular window 30 cm in diameter in a submarine can withstand a net maximum force of N without damage. What is the maximum depth in a fresh-water lake to which the submarine can go without damaging the window? The density of fresh water is 1000 kg/m 3. A) 680 m B) 750 m C) 740 m D) 1200 m 12) A container has a vertical tube, whose inner radius is mm, connected to it at its side, as shown in the figure. An unknown liquid reaches level A in the container and level B in the tube level A being 5.0 cm higher than level B. The liquid supports a 20-cm high column of oil, between levels B and C, whose density is 570 kg/m3. The mass of the oil is closest to 8) 9) 10) 11) 12) A) 410 B) 820 C) 210 D) 620 E) 1000

4 SHORT ANSWER. Write the word or phrase that best completes each statement or answers the question. 13) As shown in the figure, a large open tank contains a layer of oil ( density 450 kg/m3) floating on top of a layer of water (density 1000 kg/m3) that is 3.0 m thick, as shown in the sketch. What must be the thickness of the oil layer if the gauge pressure at the bottom of the tank is to be 8.5 x 104 Pa? 13) 14) A container consists of two vertical cylindrical columns of different diameter connected by a narrow horizontal section, as shown in the figure. The open faces of the two columns are closed by very light plates that can move up and down without friction. The tube diameter at A is 35.0 cm and at B it is 10.2 cm. This container is filled with oil of density g/cm 3. If a 125-kg object is placed on the larger plate at A, how much mass should be placed on the smaller plate at B to balance it? 14) 15) In a hydraulic garage lift, the small piston has a radius of 5.0 cm and the large piston has a radius of 15 cm. What force must be applied on the small piston in order to lift a car weighing 20,000 N on the large piston? Assume the pistons each have negligible weight. A) N B) N C) N D) N 16) If a ship has a mass of 10 million kilograms, what volume of fresh water must it displace in order to float? The density of water is 1000 kg/m 3. A) m 3 B) 10 4 m 3 C) 10 7 m 3 D) m 3 E) 10 8 m 3 15) 16) 17) A 1.00-m 3 object floats in water with 20.0% of its volume above the waterline. What does the object weigh out of the water? The density of water is 1000 kg/m 3. A) 9,800 N B) 11,800 N C) 1,960 N D) 7,840 N 18) A hollow steel ball of diameter 3.0 m just barely floats in water. What is the wall thickness of the ball? ( Fe = 7.87 g/cm 3, water = 1.00 g/cm 3 ) A) 37 cm B) 6.6 cm C) 131 cm D) 79 cm 17) 18)

5 19) A rectangular wooden block measures 10.0 cm 4.00 cm 2.00 cm. When the block is placed in water, it floats horizontally, with its bottom face 1.65 cm below the surface. What is the density of the wood? The density of water is 1.00 g/cm3. A) 1.65 g/cm3 B) g/cm3 C) 1.21 g/cm3 D) g/cm3 E) g/cm3 20) A barge with vertical sides is 10 m wide and 60 m long and is floating in fresh water of density 1000 kg/m3. How much deeper into the water does the barge sink when 3.0 x 10 5 kg of coal are loaded on the barge? A) 50 cm B) 25 cm C) 1.0 m D) 75 cm E) 1.5 m 19) 20)

TOPICS. Density. Pressure. Variation of Pressure with Depth. Pressure Measurements. Buoyant Forces-Archimedes Principle

TOPICS. Density. Pressure. Variation of Pressure with Depth. Pressure Measurements. Buoyant Forces-Archimedes Principle Lecture 6 Fluids TOPICS Density Pressure Variation of Pressure with Depth Pressure Measurements Buoyant Forces-Archimedes Principle Surface Tension ( External source ) Viscosity ( External source ) Equation

More information

EXAM 1 PHYS 103 FALL 2011 A NAME: SECTION

EXAM 1 PHYS 103 FALL 2011 A NAME: SECTION EXAM 1 PHYS 103 FALL 2011 A NAME: SECTION As a student at NJIT I, will conduct myself in a professional manner and will comply with the provisions of the NJIT Academic Honor Code. I also understand that

More information

AP Physics 2 Exam Review Questions

AP Physics 2 Exam Review Questions Chapter 10 5) When a heavy metal block is supported by a cylindrical vertical post of radius R, it exerts a force F on the post. If the diameter of the post is increased to 2R, what force does the block

More information

S.3 PHYSICS HOLIDAY WORK Where necessary assume the acceleration due to gravity, g 10ms. 1. 7. 13. 19. 25. 2. 8. 14. 20. 26. 3. 9. 15. 21. 27. 4. 10. 16. 22. 28. 5. 11. 17. 23. 29. 6. 12. 18. 24. 30. SECTION

More information

Stevens High School AP Physics II Work for Not-school

Stevens High School AP Physics II Work for Not-school 1. (AP SAMPLE QUESTION) An ideal fluid is flowing with a speed of 12 cm/s through a pipe of diameter 5 cm. The pipe splits into three smaller pipes, each with a diameter of 2 cm. What is the speed of the

More information

Name : Applied Physics II Exam One Winter Multiple Choice ( 7 Points ):

Name :   Applied Physics II Exam One Winter Multiple Choice ( 7 Points ): Name : e-mail: Applied Physics II Exam One Winter 2006-2007 Multiple Choice ( 7 Points ): 1. Pure nitrogen gas is contained in a sealed tank containing a movable piston. The initial volume, pressure and

More information

Nicholas J. Giordano. Chapter 10 Fluids

Nicholas J. Giordano.  Chapter 10 Fluids Nicholas J. Giordano www.cengage.com/physics/giordano Chapter 10 Fluids Fluids A fluid may be either a liquid or a gas Some characteristics of a fluid Flows from one place to another Shape varies according

More information

Physics - Fluids. Read Page 174 (Density) TQ1. A fluid is what type of matter? TQ2. What is fluid mechanics? TQ3. What is the equation for density?

Physics - Fluids. Read Page 174 (Density) TQ1. A fluid is what type of matter? TQ2. What is fluid mechanics? TQ3. What is the equation for density? Homework Procedure: Read pages specified in Honors Physics Essentials by Dan Fullerton. Questions labeled TQ will be questions about the text you read. These TQ s can be answered in one word, one phrase,

More information

storage tank, or the hull of a ship at rest, is subjected to fluid pressure distributed over its surface.

storage tank, or the hull of a ship at rest, is subjected to fluid pressure distributed over its surface. Hydrostatic Forces on Submerged Plane Surfaces Hydrostatic forces mean forces exerted by fluid at rest. - A plate exposed to a liquid, such as a gate valve in a dam, the wall of a liquid storage tank,

More information

Apex Grammar School O & A Level Evening Classes. Physics EVALUATION TEST PAPER. REAL EXAMINATION QUESTIONS for Secondary 4

Apex Grammar School O & A Level Evening Classes. Physics EVALUATION TEST PAPER. REAL EXAMINATION QUESTIONS for Secondary 4 Apex Grammar School O & A Level Evening Classes O Level Power Revision Series EVALUATION TEST PAPER REAL EXAMINATION QUESTIONS for Secondary 4 Name: Time Start: Date: Time End: Total Marks : / 40 40 questions

More information

A) 3.1 m/s B) 9.9 m/s C) 14 m/s D) 17 m/s E) 31 m/s

A) 3.1 m/s B) 9.9 m/s C) 14 m/s D) 17 m/s E) 31 m/s 1. A large tank, open at the top, is filled with water to a depth of 15 m. A spout located 10.0 m above the bottom of the tank is then opened as shown in the drawing. With what speed will water emerge

More information

Chapter 10. Solids & Liquids

Chapter 10. Solids & Liquids Chapter 10 Solids & Liquids Next 6 chapters use all the concepts developed in the first 9 chapters, recasting them into a form ready to apply to specific physical systems. 10.1 Phases of Matter, Mass Density

More information

Prince Sultan University Deanship of Educational Services Department of Mathematics and General Sciences

Prince Sultan University Deanship of Educational Services Department of Mathematics and General Sciences Prince Sultan University Deanship of Educational Services Department of Mathematics and General Sciences COURSE DETAILS: Introduction to Physical Science SCI101 MAJOR EXAM II Semester: First Semester --

More information

PHYS 185 Practice Final Exam Fall You may answer the questions in the space provided here, or if you prefer, on your own notebook paper.

PHYS 185 Practice Final Exam Fall You may answer the questions in the space provided here, or if you prefer, on your own notebook paper. PHYS 185 Practice Final Exam Fall 2013 Name: You may answer the questions in the space provided here, or if you prefer, on your own notebook paper. Short answers 1. 2 points When an object is immersed

More information

Figure 1 Answer: = m

Figure 1 Answer: = m Q1. Figure 1 shows a solid cylindrical steel rod of length =.0 m and diameter D =.0 cm. What will be increase in its length when m = 80 kg block is attached to its bottom end? (Young's modulus of steel

More information

1) Pressure in a fluid decreases with depth. False 1) 2) To determine gauge pressure, add the atmospheric pressure to the absolute pressure.

1) Pressure in a fluid decreases with depth. False 1) 2) To determine gauge pressure, add the atmospheric pressure to the absolute pressure. Exam 4 review Name TRUE/FALSE. Write 'T' if the statement is true and 'F' if the statement is false. 1) Pressure in a fluid decreases with depth. False 1) 2) To determine gauge pressure, add the atmospheric

More information

CHAPTER 28 PRESSURE IN FLUIDS

CHAPTER 28 PRESSURE IN FLUIDS CHAPTER 8 PRESSURE IN FLUIDS EXERCISE 18, Page 81 1. A force of 80 N is applied to a piston of a hydraulic system of cross-sectional area 0.010 m. Determine the pressure produced by the piston in the hydraulic

More information

PHYSICS 111 SPRING EXAM 3: April 12, 2016; 8:15pm - 9:45pm

PHYSICS 111 SPRING EXAM 3: April 12, 2016; 8:15pm - 9:45pm PHYSICS 111 SPRING 2016 EXAM 3: April 12, 2016; 8:15pm - 9:45pm Name (printed): Recitation Instructor: Section # INSTRUCTIONS: This exam contains 20 multiple-choice questions plus 1 extra credit question,

More information

Q1. Which of the following is the correct combination of dimensions for energy?

Q1. Which of the following is the correct combination of dimensions for energy? Tuesday, June 15, 2010 Page: 1 Q1. Which of the following is the correct combination of dimensions for energy? A) ML 2 /T 2 B) LT 2 /M C) MLT D) M 2 L 3 T E) ML/T 2 Q2. Two cars are initially 150 kilometers

More information

Find this material useful? You can help our team to keep this site up and bring you even more content consider donating via the link on our site.

Find this material useful? You can help our team to keep this site up and bring you even more content consider donating via the link on our site. Find this material useful? You can help our team to keep this site up and bring you even more content consider donating via the link on our site. Still having trouble understanding the material? Check

More information

King Fahd University of Petroleum and Minerals Department of Physics. Final Exam 041. Answer key - First choice is the correct answer

King Fahd University of Petroleum and Minerals Department of Physics. Final Exam 041. Answer key - First choice is the correct answer King Fahd University of Petroleum and Minerals Department of Physics MSK Final Exam 041 Answer key - First choice is the correct answer Q1 A 20 kg uniform ladder is leaning against a frictionless wall

More information

PHYSICS 220 Lecture 16 Fluids Textbook Sections

PHYSICS 220 Lecture 16 Fluids Textbook Sections PHYSICS 220 Lecture 16 Fluids Textbook Sections 10.1-10.4 Lecture 16 Purdue University, Physics 220 1 States of Matter Fluids Solid Hold Volume Hold Shape Liquid Hold Volume Adapt Shape Gas Adapt Volume

More information

Chapter 15. m. The symbolic equation for mass density is: ρ= m V. Table of Densities

Chapter 15. m. The symbolic equation for mass density is: ρ= m V. Table of Densities Chapter 15 Density Often you will hear that fiberglass is used for racecars because it is lighter than steel. This is only true if we build two identical bodies, one made with steel and one with fiberglass.

More information

BUSIA COUNTY JOINT EXAMINATION Kenya Certificate of Education Physics Paper 1

BUSIA COUNTY JOINT EXAMINATION Kenya Certificate of Education Physics Paper 1 NAME:.. CLASS:. ADM NO: SIGNATURE: INDEX NO: 232/1 PHYSICS PAPER 1 JULY/AUG 2014 BUSIA COUNTY JOINT EXAMINATION - 2014 Kenya Certificate of Education Physics Paper 1 Instructions to candidates This paper

More information

11.1 Mass Density. Fluids are materials that can flow, and they include both gases and liquids. The mass density of a liquid or gas is an

11.1 Mass Density. Fluids are materials that can flow, and they include both gases and liquids. The mass density of a liquid or gas is an Chapter 11 Fluids 11.1 Mass Density Fluids are materials that can flow, and they include both gases and liquids. The mass density of a liquid or gas is an important factor that determines its behavior

More information

Find this material useful? You can help our team to keep this site up and bring you even more content consider donating via the link on our site.

Find this material useful? You can help our team to keep this site up and bring you even more content consider donating via the link on our site. Find this material useful? You can help our team to keep this site up and bring you even more content consider donating via the link on our site. Still having trouble understanding the material? Check

More information

Q1. A) 46 m/s B) 21 m/s C) 17 m/s D) 52 m/s E) 82 m/s. Ans: v = ( ( 9 8) ( 98)

Q1. A) 46 m/s B) 21 m/s C) 17 m/s D) 52 m/s E) 82 m/s. Ans: v = ( ( 9 8) ( 98) Coordinator: Dr. Kunwar S. Wednesday, May 24, 207 Page: Q. A hot-air balloon is ascending (going up) at the rate of 4 m/s and when the balloon is 98 m above the ground a package is dropped from it, vertically

More information

DENSITY OF AN IRREGULAR SHAPED OBJECT

DENSITY OF AN IRREGULAR SHAPED OBJECT MASS 9/28/2017 AP PHYSICS 2 DENSITY UNIT 1 FLUID STATICS AND DYNAMICS CHAPTER 10 FLUIDS AT REST 0.12 0.1 0.08 0.06 0.04 0.02 0 MASS vs. VOLUME y = 1000x 0 0.00002 0.00004 0.00006 0.00008 0.0001 0.00012

More information

PHYSICS HYDROSTATICS FORM 5

PHYSICS HYDROSTATICS FORM 5 Pressure Pressure is defined as force per unit area. Pressure = Force Area Pressure = Newton (metre) 2 1 Pa = 1N/m 2 Which of the following exerts a greater pressure? A woman of mass 70kg stepping on your

More information

WRITE ALL YOUR CALCULATIONS IN THE BLUEBOOK PUT YOUR NAME AND THE TEST IN THE BLUEBOOK AND HAND IN

WRITE ALL YOUR CALCULATIONS IN THE BLUEBOOK PUT YOUR NAME AND THE TEST IN THE BLUEBOOK AND HAND IN Physics 6B - MWF - Midterm 1 Test #: A Name: Perm #: Section (10-11 or 12-1): You MUST put the TEST # in the first answer bubble. The TA will explain. YOU MUST do this or the test will not be graded. WRITE

More information

Question 9.1: A steel wire of length 4.7 m and cross-sectional area 3.0 10 5 m 2 stretches by the same amount as a copper wire of length 3.5 m and cross-sectional area of 4.0 10 5 m 2 under a given load.

More information

m V DEFINITION OF MASS DENSITY The mass density of a substance is the mass of a substance divided by its volume: SI Unit of Mass Density: kg/m 3

m V DEFINITION OF MASS DENSITY The mass density of a substance is the mass of a substance divided by its volume: SI Unit of Mass Density: kg/m 3 Chapter Fluids . Mass Density DEFINITION OF MASS DENSITY The mass density of a substance is the mass of a substance divided by its volume: m V SI Unit of Mass Density: kg/m 3 . Mass Density . Mass Density

More information

Question Figure shows the strain-stress curve for a given material. What are (a) Young s modulus and (b) approximate yield strength for this material?

Question Figure shows the strain-stress curve for a given material. What are (a) Young s modulus and (b) approximate yield strength for this material? Question. A steel wire of length 4.7 m and cross-sectional area 3.0 x 10-5 m 2 stretches by the same amount as a copper wire of length 3.5 m and cross-sectional area of 4.0 x 10-5 m 2 under a given load.

More information

Please choose the letter corresponding to the best answer to each problem (5 pts each).

Please choose the letter corresponding to the best answer to each problem (5 pts each). Please choose the letter corresponding to the best answer to each problem (5 pts each). 1. A 10-m uniform horizontal beam of weight 75 N is supported by two vertical posts. The left post is at the left

More information

Class XI Physics. Ch. 9: Mechanical Properties of solids. NCERT Solutions

Class XI Physics. Ch. 9: Mechanical Properties of solids. NCERT Solutions Downloaded from Class XI Physics Ch. 9: Mechanical Properties of solids NCERT Solutions Page 242 Question 9.1: A steel wire of length 4.7 m and cross-sectional area 3.0 10 5 m 2 stretches by the same amount

More information

CPO Science Foundations of Physics. Unit 8, Chapter 27

CPO Science Foundations of Physics. Unit 8, Chapter 27 CPO Science Foundations of Physics Unit 8, Chapter 27 Unit 8: Matter and Energy Chapter 27 The Physical Properties of Matter 27.1 Properties of Solids 27.2 Properties of Liquids and Fluids 27.3 Properties

More information

CHAPTER 13. Liquids FLUIDS FLUIDS. Gases. Density! Bulk modulus! Compressibility. To begin with... some important definitions...

CHAPTER 13. Liquids FLUIDS FLUIDS. Gases. Density! Bulk modulus! Compressibility. To begin with... some important definitions... CHAPTER 13 FLUIDS Density! Bulk modulus! Compressibility Pressure in a fluid! Hydraulic lift! Hydrostatic paradox Measurement of pressure! Manometers and barometers Buoyancy and Archimedes Principle! Upthrust!

More information

M10/4/PHYSI/SPM/ENG/TZ1/XX+ Physics Standard level Paper 1. Monday 10 May 2010 (afternoon) 45 minutes INSTRUCTIONS TO CANDIDATES

M10/4/PHYSI/SPM/ENG/TZ1/XX+ Physics Standard level Paper 1. Monday 10 May 2010 (afternoon) 45 minutes INSTRUCTIONS TO CANDIDATES M1/4/PHYSI/SPM/ENG/TZ1/XX+ 221651 Physics Standard level Paper 1 Monday 1 May 21 (afternoon) 45 minutes INSTRUCTIONS TO CANDIDATES Do not open this examination paper until instructed to do so. Answer all

More information

Chapter 15: Fluid Mechanics Dynamics Using Pascal s Law = F 1 = F 2 2 = F 2 A 2

Chapter 15: Fluid Mechanics Dynamics Using Pascal s Law = F 1 = F 2 2 = F 2 A 2 Lecture 24: Archimedes Principle and Bernoulli s Law 1 Chapter 15: Fluid Mechanics Dynamics Using Pascal s Law Example 15.1 The hydraulic lift A hydraulic lift consists of a small diameter piston of radius

More information

9 MECHANICAL PROPERTIES OF SOLIDS

9 MECHANICAL PROPERTIES OF SOLIDS 9 MECHANICAL PROPERTIES OF SOLIDS Deforming force Deforming force is the force which changes the shape or size of a body. Restoring force Restoring force is the internal force developed inside the body

More information

I N V E S T I C E D O R O Z V O J E V Z D Ě L Á V Á N Í

I N V E S T I C E D O R O Z V O J E V Z D Ě L Á V Á N Í MECHNICS O LUIDS luids are both liquids and gases. The common property of fluids is that the particles can be separated easily (liquids do not have their own shape etc.). Real fluids have something like

More information

Physics 107 HOMEWORK ASSIGNMENT #9

Physics 107 HOMEWORK ASSIGNMENT #9 Physics 07 HOMEORK ASSIGNMENT #9 Cutnell & Johnson, 7 th edition Chapter : Problems 6, 8, 33, 40, 44 *6 A 58-kg skier is going down a slope oriented 35 above the horizontal. The area of each ski in contact

More information

Physics 101: Lecture 17 Fluids

Physics 101: Lecture 17 Fluids Exam III Physics 101: Lecture 17 Fluids Exam 2 is Mon Nov. 4, 7pm Extra office hours on Fri. (see webpage!) Physics 101: Lecture 17, Pg 1 Homework 9 Help A block of mass M 1 = 3 kg rests on a table with

More information

PHYS102 Previous Exam Problems. Temperature, Heat & The First Law of Thermodynamics

PHYS102 Previous Exam Problems. Temperature, Heat & The First Law of Thermodynamics PHYS102 Previous Exam Problems CHAPTER 18 Temperature, Heat & The First Law of Thermodynamics Equilibrium & temperature scales Thermal expansion Exchange of heat First law of thermodynamics Heat conduction

More information

Physics 220: Classical Mechanics

Physics 220: Classical Mechanics Lecture /33 Phys 0 Physics 0: Classical Mechanics Lecture: MWF 8:40 am 9:40 am (Phys 4) Michael Meier mdmeier@purdue.edu Office: Phys Room 38 Help Room: Phys Room schedule on course webpage Office Hours:

More information

CH 10: PRESSURE, GRAVITY AND MOMENTS

CH 10: PRESSURE, GRAVITY AND MOMENTS CH 10: PRESSURE, GRAVITY AND MOMENTS Exercise 10.1: Page 104 1. Convert each of the following to kg: (i) 200 g (ii) 4 g (iii) 2 x 10 5 g (iv) 24 mg 2. Convert each of the following to m 3 : (i) 1 cm 3

More information

Physics 5B Practice Problems 3

Physics 5B Practice Problems 3 Physics 5B Practice Problems 3 Eric Reichwein Department of Physics University of California, Santa Cruz March 13, 213 1 Multiple Choice Section 1. A fresh-pure-water ice cube is floating in a glass filled

More information

Question 9.1: Answer. Length of the steel wire, L 1 = 4.7 m. Area of cross-section of the steel wire, A 1 = m 2

Question 9.1: Answer. Length of the steel wire, L 1 = 4.7 m. Area of cross-section of the steel wire, A 1 = m 2 Question 9.1: A steel wire of length 4.7 m and cross-sectional area 3.0 10 5 m 2 stretches by the same amount as a copper wire of length 3.5 m and cross-sectional area of 4.0 10 5 m 2 under a given load.

More information

Physics 17 Exam #3 November 9, 2009

Physics 17 Exam #3 November 9, 2009 Physics 17 Exam #3 November 9, 2009 Atomic Weights hydrogen: 1 carbon: 12 oxygen: 16 nitrogen: 14 Atmospheric pressure at sea level = 101,000 Pa, or 14.7 lbs/in 2 Specific heat capacity of water = 1.0

More information

Liquids CHAPTER 13 FLUIDS FLUIDS. Gases. Density! Bulk modulus! Compressibility. To begin with... some important definitions...

Liquids CHAPTER 13 FLUIDS FLUIDS. Gases. Density! Bulk modulus! Compressibility. To begin with... some important definitions... CHAPTER 13 FLUIDS FLUIDS Liquids Gases Density! Bulk modulus! Compressibility Pressure in a fluid! Hydraulic lift! Hydrostatic paradox Measurement of pressure! Manometers and barometers Buoyancy and Archimedes

More information

Hydrostatics. ENGR 5961 Fluid Mechanics I: Dr. Y.S. Muzychka

Hydrostatics. ENGR 5961 Fluid Mechanics I: Dr. Y.S. Muzychka 1 Hydrostatics 2 Introduction In Fluid Mechanics hydrostatics considers fluids at rest: typically fluid pressure on stationary bodies and surfaces, pressure measurements, buoyancy and flotation, and fluid

More information

That teaches better, that feels better. Mass Volume and Density. Over Betuwe College 2013 Page 1

That teaches better, that feels better. Mass Volume and Density. Over Betuwe College 2013 Page 1 Mass Volume and Density Over Betuwe College 2013 Page 1 Contents 1 Volume... 3 1.1 Calculating volume.... 3 1.2 Volume 2... 5 1.3 Symbols and conversion.... 5 2 Mass... 6 3 Density... 7 3.1 The ratio table...

More information

Exam 4--PHYS 101--Fall 2016

Exam 4--PHYS 101--Fall 2016 Name: Exam 4--PHYS 101--Fall 2016 Multiple Choice Identify the choice that best completes the statement or answers the question. 1. A bus contains a 2000 kg flywheel (a disk that has a 0.500 m radius)

More information

Class XI Chapter 9 Mechanical Properties of Solids Physics

Class XI Chapter 9 Mechanical Properties of Solids Physics Book Name: NCERT Solutions Question : A steel wire of length 4.7 m and cross-sectional area 5 3.0 0 m stretches by the same 5 amount as a copper wire of length 3.5 m and cross-sectional area of 4.0 0 m

More information

UNIVERSITY OF MANITOBA. All questions are of equal value. No marks are subtracted for wrong answers.

UNIVERSITY OF MANITOBA. All questions are of equal value. No marks are subtracted for wrong answers. (3:30 pm 6:30 pm) PAGE NO.: 1 of 7 All questions are of equal value. No marks are subtracted for wrong answers. Record all answers on the computer score sheet provided. USE PENCIL ONLY! Black pen will

More information

1. A pure shear deformation is shown. The volume is unchanged. What is the strain tensor.

1. A pure shear deformation is shown. The volume is unchanged. What is the strain tensor. Elasticity Homework Problems 2014 Section 1. The Strain Tensor. 1. A pure shear deformation is shown. The volume is unchanged. What is the strain tensor. 2. Given a steel bar compressed with a deformation

More information

UNIVERSITY OF MANITOBA. Equal marks for all questions. No marks are subtracted for wrong answers.

UNIVERSITY OF MANITOBA. Equal marks for all questions. No marks are subtracted for wrong answers. PAGE NO.: 1 of 5 Equal marks for all questions. No marks are subtracted for wrong answers. Record all answers on the computer score sheet provided. USE PENCIL ONLY! Black pen will look good but may not

More information

UIC PHYSICS 105 Fall 2014 Practice Final Exam. UIC Physics 105. Practice Final Exam. Fall 2014 Best if used by December 7 PROBLEM POINTS SCORE

UIC PHYSICS 105 Fall 2014 Practice Final Exam. UIC Physics 105. Practice Final Exam. Fall 2014 Best if used by December 7 PROBLEM POINTS SCORE UIC Physics 105 Practice Final Exam Fall 2014 Best if used by December 7 PROBLEM POINTS SCORE Multiple Choice Problem 1 Problem 2 Problem 3 Problem 4 Problem 5 50 11 8 7 11 13 Total 100 Page 1 of 7 MULTIPLE

More information

Fluid Mechanics. Chapter 14. Modified by P. Lam 6_7_2012

Fluid Mechanics. Chapter 14. Modified by P. Lam 6_7_2012 Chapter 14 Fluid Mechanics PowerPoint Lectures for University Physics, Twelfth Edition Hugh D. Young and Roger A. Freedman Lectures by James Pazun Modified by P. Lam 6_7_2012 Goals for Chapter 14 To study

More information

Engineering Mechanics. Equivalent force systems: problems

Engineering Mechanics. Equivalent force systems: problems Engineering Mechanics Equivalent force systems: problems A 36-N force is applied to a wrench to tighten a showerhead. Knowing that the centerline of the wrench is parallel to the x axis. Determine the

More information

22 Which of the following correctly defines the terms stress, strain and Young modulus? stress strain Young modulus

22 Which of the following correctly defines the terms stress, strain and Young modulus? stress strain Young modulus PhysicsndMathsTutor.com Which of the following correctly defines the terms stress, strain and Young modulus? 97/1/M/J/ stress strain Young modulus () x (area) (extension) x (original length) (stress) /

More information

Page 1. Physics 131: Lecture 23. Today s Agenda. Announcements. States of Matter

Page 1. Physics 131: Lecture 23. Today s Agenda. Announcements. States of Matter Physics 131: Lecture 3 Today s Agenda Description of Fluids at Rest Pressure vs Depth Pascal s Principle: hydraulic forces Archimedes Principle: objects in a fluid Bernoulli s equation Physics 01: Lecture

More information

(Refer Slide Time: 0:28)

(Refer Slide Time: 0:28) Engineering Thermodynamics Professor Jayant K Singh Department of Chemical Engineering Indian Institute of Technology Kanpur Lecture 08 Examples on basic concept & energy balance Welcome back! Myself Parul

More information

1 atm = 1.01x10 Pa = 760 Torr = 14.7 lb / in

1 atm = 1.01x10 Pa = 760 Torr = 14.7 lb / in Last class we began discussion of ressure in fluids, with ressure defined as, F = ; units N 1 Pa = 1 m 2 There are a number of other ressure units in common use having the following equivalence, 5 2 1

More information

Chapter 9: Solids and Fluids

Chapter 9: Solids and Fluids Chapter 9: Solids and Fluids State of matters: Solid, Liquid, Gas and Plasma. Solids Has definite volume and shape Can be crystalline or amorphous Molecules are held in specific locations by electrical

More information

Jordan University of Science & Technology PHYS 101A Final exam First semester 2007

Jordan University of Science & Technology PHYS 101A Final exam First semester 2007 Student Name Student ID Jordan University of Science & Technology PHYS 101A Final exam First semester 2007 Approximate your answer to those given for each question. Use this table to fill in your answer

More information

PH1011 Tut 4: Forces, Momentum and Impulse

PH1011 Tut 4: Forces, Momentum and Impulse PH1011 Tut 4: Forces, Momentum and Impulse 1) [ A J86/II/8] When a body moves through a fluid, a retarding force due to turbulence may be experienced. In the case of a sphere of radius r moving with speed

More information

Chapter 9 Solids and Fluids. Elasticity Archimedes Principle Bernoulli s Equation

Chapter 9 Solids and Fluids. Elasticity Archimedes Principle Bernoulli s Equation Chapter 9 Solids and Fluids Elasticity Archimedes Principle Bernoulli s Equation States of Matter Solid Liquid Gas Plasmas Solids: Stress and Strain Stress = Measure of force felt by material Stress= Force

More information

8.4 Density and 8.5 Work Group Work Target Practice

8.4 Density and 8.5 Work Group Work Target Practice 8.4 Density and 8.5 Work Group Work Target Practice 1. The density of oil in a circular oil slick on the surface of the ocean at a distance meters from the center of the slick is given by δ(r) = 5 1+r

More information

ME-B41 Lab 1: Hydrostatics. Experimental Procedures

ME-B41 Lab 1: Hydrostatics. Experimental Procedures ME-B41 Lab 1: Hydrostatics In this lab you will do four brief experiments related to the following topics: manometry, buoyancy, forces on submerged planes, and hydraulics (a hydraulic jack). Each experiment

More information

Fluidi. Copyright 2015 John Wiley & Sons, Inc. All rights reserved.

Fluidi. Copyright 2015 John Wiley & Sons, Inc. All rights reserved. Fluidi 11.1 Mass Density DEFINITION OF MASS DENSITY The mass density of a substance is the mass of a substance divided by its volume: m V SI Unit of Mass Density: kg/m3 11.1 Mass Density 11.1 Mass Density

More information

FE Fluids Review March 23, 2012 Steve Burian (Civil & Environmental Engineering)

FE Fluids Review March 23, 2012 Steve Burian (Civil & Environmental Engineering) Topic: Fluid Properties 1. If 6 m 3 of oil weighs 47 kn, calculate its specific weight, density, and specific gravity. 2. 10.0 L of an incompressible liquid exert a force of 20 N at the earth s surface.

More information

Modeling with Volume

Modeling with Volume 1.2 Modeling with Essential Question How can you use the mass and volume of an object to describe the density of the object? Finding Densities Work with a partner. Approximate the volume of each object

More information

Chapter 10 - Mechanical Properties of Fluids. The blood pressure in humans is greater at the feet than at the brain

Chapter 10 - Mechanical Properties of Fluids. The blood pressure in humans is greater at the feet than at the brain Question 10.1: Explain why The blood pressure in humans is greater at the feet than at the brain Atmospheric pressure at a height of about 6 km decreases to nearly half of its value at the sea level, though

More information

5 In a factory, regular stacks, each containing 150 pieces of paper, are measured using a pair of vernier calipers. The reading of one stack is shown.

5 In a factory, regular stacks, each containing 150 pieces of paper, are measured using a pair of vernier calipers. The reading of one stack is shown. PURE PHYSICS MECHANICS (PART I) 1 State the symbol of the SI unit for the following physical quantities. (a) Temperature (b) Density (c) Weight (d) Acceleration 2 For each of the following formula, derive

More information

i. Indicate on the figure the point P at which the maximum speed of the car is attained. ii. Calculate the value vmax of this maximum speed.

i. Indicate on the figure the point P at which the maximum speed of the car is attained. ii. Calculate the value vmax of this maximum speed. 1. A 0.20 kg object moves along a straight line. The net force acting on the object varies with the object's displacement as shown in the graph above. The object starts from rest at displacement x = 0

More information

Exam 3--Fall 08--PHYS 101

Exam 3--Fall 08--PHYS 101 Name: Class: Date: Exam 3--Fall 08--PHYS 101 Multiple Choice Identify the choice that best completes the statement or answers the question. 1. An object at rest begins to rotate with a constant angular

More information

Solution to phys101-t112-final Exam

Solution to phys101-t112-final Exam Solution to phys101-t112-final Exam Q1. An 800-N man stands halfway up a 5.0-m long ladder of negligible weight. The base of the ladder is.0m from the wall as shown in Figure 1. Assuming that the wall-ladder

More information

States of Matter. Chapter 9 Solids and Fluids. Solids: Stress and Strain. Solids: Stress and Strain. Stress = Force Area. Strain =!

States of Matter. Chapter 9 Solids and Fluids. Solids: Stress and Strain. Solids: Stress and Strain. Stress = Force Area. Strain =! Elasticity Chapter 9 Solids and Fluids Archimedes Principle Bernoulli s Equation Solid Liquid Gas Plasmas States of Matter 1 2 Solids: Stress and Strain Solids: Stress and Strain Stress = Measure of force

More information

States of Matter. Chapter 9 Solids and Fluids. Solids: Stress and Strain. Solids: Stress and Strain. Stress = Force Area. Strain =!L L. Example 9.

States of Matter. Chapter 9 Solids and Fluids. Solids: Stress and Strain. Solids: Stress and Strain. Stress = Force Area. Strain =!L L. Example 9. Elasticity Chapter 9 Solids and Fluids Archimedes Principle Bernoulli s Equation Solid Liquid Gas Plasmas States of Matter Solids: Stress and Strain Solids: Stress and Strain Stress = Measure of force

More information

All questions are of equal value. No marks are subtracted for wrong answers.

All questions are of equal value. No marks are subtracted for wrong answers. (1:30 PM 4:30 PM) Page 1 of 6 All questions are of equal value. No marks are subtracted for wrong answers. Record all answers on the computer score sheet provided. USE PENCIL ONLY! Black pen will look

More information

Physics 6B. Practice Midterm #1 Solutions

Physics 6B. Practice Midterm #1 Solutions Physics 6B Practice Midterm #1 Solutions 1. A block of plastic with a density of 90 kg/m 3 floats at the interface between of density 850 kg/m 3 and of density 1000 kg/m 3, as shown. Calculate the percentage

More information

Some physical constants:

Some physical constants: E= mc 2 ρhysics Ωlympiad Symbol No.: College: Grade: Some physical constants: g = 9.8 N/kg G = 6.67 10 11 N m 2 /kg 2 k = 1/4πԑ0 = 8.99 109 N m 2 /C 2 c = 3.00 108 m/s k B = 1.38 10 23 J/K N A = 6.02 1023

More information

NAME: Given Formulae: Law of Cosines: Law of Sines:

NAME: Given Formulae: Law of Cosines: Law of Sines: NME: Given Formulae: Law of Cosines: EXM 3 PST PROBLEMS (LESSONS 21 TO 28) 100 points Thursday, November 16, 2017, 7pm to 9:30, Room 200 You are allowed to use a calculator and drawing equipment, only.

More information

AP Physics C: Work, Energy, and Power Practice

AP Physics C: Work, Energy, and Power Practice AP Physics C: Work, Energy, and Power Practice 1981M2. A swing seat of mass M is connected to a fixed point P by a massless cord of length L. A child also of mass M sits on the seat and begins to swing

More information

Making measurements. density the ratio of mass to volume for a substance

Making measurements. density the ratio of mass to volume for a substance Block 1 General physics 1A definition to learn density the ratio of mass to volume for a substance Making measurements An equation to learn and use density = mass volume Exercise 1.1 Accurate measurements

More information

Moving earth crust. 100 m

Moving earth crust. 100 m example An architect wants to design a 5 m high circular pillar with a radius of 0.5 m that holds a bronze statue that weighs 1.0E+04 kg. He chooses concrete for the material of the pillar (Y=1.0E+10 Pa).

More information

Test 3 Preparation Questions

Test 3 Preparation Questions Test 3 Preparation Questions A1. Which statement is true concerning an object executing simple harmonic motion? (A) Its velocity is never zero. (B) Its acceleration is never zero. (C) Its velocity and

More information

Fluids. Fluid = Gas or Liquid. Density Pressure in a Fluid Buoyancy and Archimedes Principle Fluids in Motion

Fluids. Fluid = Gas or Liquid. Density Pressure in a Fluid Buoyancy and Archimedes Principle Fluids in Motion Chapter 14 Fluids Fluids Density Pressure in a Fluid Buoyancy and Archimedes Principle Fluids in Motion Fluid = Gas or Liquid MFMcGraw-PHY45 Chap_14Ha-Fluids-Revised 10/13/01 Densities MFMcGraw-PHY45 Chap_14Ha-Fluids-Revised

More information

Chapter 9. Solids and Fluids

Chapter 9. Solids and Fluids Chapter 9 Solids and Fluids States of Matter Solid Liquid Gas Plasma Solids Have definite volume Have definite shape Atoms or molecules are held in specific locations By electrical forces Vibrate about

More information

m V DEFINITION OF MASS DENSITY The mass density of a substance is the mass of a substance divided by its volume: SI Unit of Mass Density: kg/m 3

m V DEFINITION OF MASS DENSITY The mass density of a substance is the mass of a substance divided by its volume: SI Unit of Mass Density: kg/m 3 Chapter 11 Fluids 11.1 Mass Density DEFINITION OF MASS DENSITY The mass density of a substance is the mass of a substance divided by its volume: ρ m V SI Unit of Mass Density: kg/m 3 11.1 Mass Density

More information

Semester One Test Review

Semester One Test Review Semester One Test Review Net Forces a. 5N 2N b. 5N 3N c. 3N 3N d. 2N 4N 2N 1. Which forces diagrams above show a Net Force of zero? a. All of them b. None of them c. c only d. c and d 2. Which force diagrams

More information

AP Physics 1 Lesson 9 Homework Outcomes. Name

AP Physics 1 Lesson 9 Homework Outcomes. Name AP Physics 1 Lesson 9 Homework Outcomes Name Date 1. Define uniform circular motion. 2. Determine the tangential velocity of an object moving with uniform circular motion. 3. Determine the centripetal

More information

Physics 123 Unit #1 Review

Physics 123 Unit #1 Review Physics 123 Unit #1 Review I. Definitions & Facts Density Specific gravity (= material / water) Pressure Atmosphere, bar, Pascal Barometer Streamline, laminar flow Turbulence Gauge pressure II. Mathematics

More information

SCIENCE (PAPER 1) Physics

SCIENCE (PAPER 1) Physics SCIENCE (PAPER 1) Physics (Two hours) Answers to this paper must be written on the paper provided separately. You will not be allowed to write during the first 15 minutes. This time is to be spent in reading

More information

CHAPTERS 12 and 13 Review Questions

CHAPTERS 12 and 13 Review Questions HCC Physics 1305 CHAPTERS 12 and 13 Review Questions Multiple Choice Identify the choice that best completes the statement or answers the question. 1. Which of the four states of matter occurs at the highest

More information

States of matter. Density high > high >> low (pressure dependent)

States of matter. Density high > high >> low (pressure dependent) Fluids States of matter Solids Fluids crystalline amorphous liquids gasses Inter-atomic forces strong > strong >> very weak Density high > high >> low (pressure dependent) Density is an important material

More information

AP Physics B Summer Assignment

AP Physics B Summer Assignment BERGEN COUNTY TECHNICAL SCHOOL AP Physics B Summer Assignment 2011 Solve all problems on separate paper. This will be due the first week of school. If you need any help you can e-mail Mr. Zavorotniy at

More information

Physics 207 Lecture 18

Physics 207 Lecture 18 Physics 07, Lecture 8, Nov. 6 MidTerm Mean 58.4 (64.6) Median 58 St. Dev. 6 (9) High 94 Low 9 Nominal curve: (conservative) 80-00 A 6-79 B or A/B 34-6 C or B/C 9-33 marginal 9-8 D Physics 07: Lecture 8,

More information

MULTIPLE-CHOICE PROBLEMS:(Two marks per answer) (Circle the Letter Beside the Most Correct Answer in the Questions Below.)

MULTIPLE-CHOICE PROBLEMS:(Two marks per answer) (Circle the Letter Beside the Most Correct Answer in the Questions Below.) MULTIPLE-CHOICE PROLEMS:(Two marks per answer) (Circle the Letter eside the Most Correct Answer in the Questions elow.) 1. The absolute viscosity µ of a fluid is primarily a function of: a. Density. b.

More information