Sampling and Discrete Time. Discrete-Time Signal Description. Sinusoids. Sampling and Discrete Time. Sinusoids An Aperiodic Sinusoid.
|
|
|
- Mercy Powell
- 5 years ago
- Views:
Transcription
1 Sampling and Discrete Time Discrete-Time Signal Description Sampling is the acquisition of the values of a continuous-time signal at discrete points in time. x t discrete-time signal. ( ) is a continuous-time signal, x n x n = x ( nt s ) where T s is the time between samples is a M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 1 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl Sampling and Discrete Time The general form of a periodic sinusoid with fundamental period N 0 is g n [ ] = Acos( πf 0 n +θ) or Acos( Ω 0 n +θ) Unlike a continuous-time sinusoid, a discrete-time sinusoid is not necessarily periodic. If a sinusoid has the form g[ n] = Acos( πf 0 n +θ) then F 0 must be a ratio of integers (a rational number) for g[ n] to be periodic. If F 0 is rational in the form q / N 0 and all common factors in q and N 0 have been cancelled, then the fundamental period of the sinusoid is N 0, not N 0 / q (unless q = 1). M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 3 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 4 Periodic Periodic An Aperiodic Sinusoid Periodic Aperiodic M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 5 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 6 1
2 Two sinusoids whose analytical expressions look different, g 1 [ n] = Acos( πf 01 n +θ) and g [ n] = Acos( πf 0 n +θ) may actually be the same. If F 0 = F 01 + m, where m is an integer then (because n is discrete time and therefore an integer), ( ) = Acos( πf 0 n +θ) (Example on next slide) Acos πf 01 n +θ M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 7 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 8 Exponentials Real α Complex α M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 9 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 10 The Unit Impulse Function [ ] = 1, n = 0 δ n 0, n 0 The discrete-time unit impulse (also known as the Kronecker delta function ) is a function in the ordinary sense (in contrast with the continuous-time unit impulse). It has a sampling property, Aδ [ n n 0 ]x[ n] = Ax n 0 n= but no scaling property. That is, δ n [ ] [ ] = δ [ an] for any non-zero, finite integer a. The Unit Sequence Function [ ] = 1, n 0 u n 0, n < 0 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 11 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 1
3 The Signum Function 1, n > 0 sgn n = 0, n = 0 1, n < 0 The Unit Ramp Function ramp n [ ] = n, n 0 0, n < 0 = n u n n [ ] = u[ m 1] m= M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 13 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 14 The Periodic Impulse Function Let g[ n] be graphically defined by δ N [ n] = δ n mn m= [ ] g[ n] = 0, n >15 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 15 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 16 Time shifting n n + n 0, n 0 an integer Time compression n Kn K an integer > 1 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 17 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 18 3
4 Time expansion n n / K, K > 1 For all n such that n / K is an integer, g[ n / K ] is defined. For all n such that n / K is not an integer, g[ n / K ] is not defined. There is a form of time expansion that is useful. Let [ ] = x [ n / m ], n / m an integer y n 0, otherwise All values of y are defined. This type of time expansion is actually used in some digital signal processing operations. M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 19 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 0 Differencing Accumulation [ ] = h[ m] g n n m= M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 1 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl Even and Odd Signals g[ n] = g[ n] g[ n] = g[ n] Products of Even and Odd Functions Two Even Functions g e [ ] + g[ n] [ n] = g n g o [ ] g[ n] [ n] = g n M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 3 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 4 4
5 Products of Even and Odd Functions An Even Function and an Odd Function Products of Even and Odd Functions Two Odd Functions M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 5 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 6 Symmetric Finite Summation Periodic Functions A periodic function is one that is invariant to the change of variable n n + mn where N is a period of the function and m is any integer. The minimum positive integer value of N for which [ ] = g[ n + N ] is called the fundamental period N 0. g n N g[ n] = g 0 n= N N g[ n] = 0 [ ] + g[ n] n=1 N n= N M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 7 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 8 Periodic Functions The signal energy of a signal x[ n] is E x = n= x[ n] M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 9 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 30 5
6 x[ n] = 0, n > 31 Find the signal energy of n= [ ] = x n ( 5 / 3) n, 0 n < 8 0, otherwise 7 n=0 ( ) n ( ) 4 E x = x[ n] = 5 / 3 = 5 / 3 N 1 N, r = 1 Using r n = 1 r N n=0, r 1 1 r 8 ( )4 E x = 1 5 / / 3 7 n=0 ( ) n M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 31 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 3 Some signals have infinite signal energy. In that case It is usually more convenient to deal with average signal power. The average signal power of a signal x n 1 P x = lim N N For a periodic signal x n P x = 1 N N 1 n= N x[ n] [ ] is [ ] the average signal power is n= N x[ n] The notation means the sum over any set of n= N consecutive n's exactly N in length. M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 33 M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 34 A signal with finite signal energy is called an energy signal. A signal with infinite signal energy and finite average signal power is called a power signal. M. J. Roberts - All Rights Reserved. Edited by Dr. Robert Akl 35 6
Section 3 Discrete-Time Signals EO 2402 Summer /05/2013 EO2402.SuFY13/MPF Section 3 1
Section 3 Discrete-Time Signals EO 2402 Summer 2013 07/05/2013 EO2402.SuFY13/MPF Section 3 1 [p. 3] Discrete-Time Signal Description Sampling, sampling theorem Discrete sinusoidal signal Discrete exponential
Mathematical Description of Discrete-Time Signals. 9/10/16 M. J. Roberts - All Rights Reserved 1
Mathematical Descriptio of Discrete-Time Sigals 9/10/16 M. J. Roberts - All Rights Reserved 1 Samplig ad Discrete Time Samplig is the acquisitio of the values of a cotiuous-time sigal at discrete poits
Generalizing the DTFT!
The Transform Generaliing the DTFT! The forward DTFT is defined by X e jω ( ) = x n e jωn in which n= Ω is discrete-time radian frequency, a real variable. The quantity e jωn is then a complex sinusoid
The Discrete-time Fourier Transform
The Discrete-time Fourier Transform Rui Wang, Assistant professor Dept. of Information and Communication Tongji University it Email: ruiwang@tongji.edu.cn Outline Representation of Aperiodic signals: The
6.003: Signal Processing
6.003: Signal Processing Discrete Fourier Transform Discrete Fourier Transform (DFT) Relations to Discrete-Time Fourier Transform (DTFT) Relations to Discrete-Time Fourier Series (DTFS) October 16, 2018
Chapter 1 Fundamental Concepts
Chapter 1 Fundamental Concepts 1 Signals A signal is a pattern of variation of a physical quantity, often as a function of time (but also space, distance, position, etc). These quantities are usually the
Chapter 1 Fundamental Concepts
Chapter 1 Fundamental Concepts Signals A signal is a pattern of variation of a physical quantity as a function of time, space, distance, position, temperature, pressure, etc. These quantities are usually
z Transform System Analysis
z Transform System Analysis Block Diagrams and Transfer Functions Just as with continuous-time systems, discrete-time systems are conveniently described by block diagrams and transfer functions can be
Chapter 13 Z Transform
Chapter 13 Z Transform 1. -transform 2. Inverse -transform 3. Properties of -transform 4. Solution to Difference Equation 5. Calculating output using -transform 6. DTFT and -transform 7. Stability Analysis
ENT 315 Medical Signal Processing CHAPTER 2 DISCRETE FOURIER TRANSFORM. Dr. Lim Chee Chin
ENT 315 Medical Signal Processing CHAPTER 2 DISCRETE FOURIER TRANSFORM Dr. Lim Chee Chin Outline Introduction Discrete Fourier Series Properties of Discrete Fourier Series Time domain aliasing due to frequency
Solution of ECE 315 Test #1 Su03
Solution of ECE 5 Test # Su I. point each. A CT function is time inverted and looks the same as it did before it was time inverted. What kind of function is it? Even function Answers like rect or sinc
Representing a Signal
The Fourier Series Representing a Signal The convolution method for finding the response of a system to an excitation takes advantage of the linearity and timeinvariance of the system and represents the
EQ: What are limits, and how do we find them? Finite limits as x ± Horizontal Asymptote. Example Horizontal Asymptote
Finite limits as x ± The symbol for infinity ( ) does not represent a real number. We use to describe the behavior of a function when the values in its domain or range outgrow all finite bounds. For example,
Continuous-time Signals. (AKA analog signals)
Continuous-time Signals (AKA analog signals) I. Analog* Signals review Goals: - Common test signals used in system analysis - Signal operations and properties: scaling, shifting, periodicity, energy and
Review of Discrete-Time System
Review of Discrete-Time System Electrical & Computer Engineering University of Maryland, College Park Acknowledgment: ENEE630 slides were based on class notes developed by Profs. K.J. Ray Liu and Min Wu.
Discrete-Time Signals: Time-Domain Representation
Discrete-Time Signals: Time-Domain Representation 1 Signals represented as sequences of numbers, called samples Sample value of a typical signal or sequence denoted as x[n] with n being an integer in the
Lecture 8: Discrete-Time Signals and Systems Dr.-Ing. Sudchai Boonto
Dr-Ing Sudchai Boonto Department of Control System and Instrumentation Engineering King Mongut s Unniversity of Technology Thonburi Thailand Outline Introduction Some Useful Discrete-Time Signal Models
Theory and Problems of Signals and Systems
SCHAUM'S OUTLINES OF Theory and Problems of Signals and Systems HWEI P. HSU is Professor of Electrical Engineering at Fairleigh Dickinson University. He received his B.S. from National Taiwan University
Flash File. Module 3 : Sampling and Reconstruction Lecture 28 : Discrete time Fourier transform and its Properties. Objectives: Scope of this Lecture:
Module 3 : Sampling and Reconstruction Lecture 28 : Discrete time Fourier transform and its Properties Objectives: Scope of this Lecture: In the previous lecture we defined digital signal processing and
Communication Signals (Haykin Sec. 2.4 and Ziemer Sec Sec. 2.4) KECE321 Communication Systems I
Communication Signals (Haykin Sec..4 and iemer Sec...4-Sec..4) KECE3 Communication Systems I Lecture #3, March, 0 Prof. Young-Chai Ko 년 3 월 일일요일 Review Signal classification Phasor signal and spectra Representation
Fourier Transform for Continuous Functions
Fourier Transform for Continuous Functions Central goal: representing a signal by a set of orthogonal bases that are corresponding to frequencies or spectrum. Fourier series allows to find the spectrum
Review of Analog Signal Analysis
Review of Analog Signal Analysis Chapter Intended Learning Outcomes: (i) Review of Fourier series which is used to analyze continuous-time periodic signals (ii) Review of Fourier transform which is used
System Processes input signal (excitation) and produces output signal (response)
Signal A funcion of ime Sysem Processes inpu signal (exciaion) and produces oupu signal (response) Exciaion Inpu Sysem Oupu Response 1. Types of signals 2. Going from analog o digial world 3. An example
( ) ( ) numerically using the DFT. The DTFT is defined. [ ]e. [ ] = x n. [ ]e j 2π Fn and the DFT is defined by X k. [ ]e j 2π kn/n with N = 5.
![( ) ( ) numerically using the DFT. The DTFT is defined. [ ]e. [ ] = x n. [ ]e j 2π Fn and the DFT is defined by X k. [ ]e j 2π kn/n with N = 5.](/thumbs/88/116792961.jpg "( ) ( ) numerically using the DFT. The DTFT is defined. [ ]e. [ ] = x n. [ ]e j 2π Fn and the DFT is defined by X k. [ ]e j 2π kn/n with N = 5.")
( /13) in the Ω form. ind the DTT of 8rect 3 n 2 8rect ( 3( n 2) /13) 40drcl(,5)e j 4π Let = Ω / 2π. Then 8rect 3 n 2 40 drcl( Ω / 2π,5)e j 2Ω ( /13) ind the DTT of 8rect 3( n 2) /13 by X = x n numerically
A system that is both linear and time-invariant is called linear time-invariant (LTI).
The Cooper Union Department of Electrical Engineering ECE111 Signal Processing & Systems Analysis Lecture Notes: Time, Frequency & Transform Domains February 28, 2012 Signals & Systems Signals are mapped
Solution of ODEs using Laplace Transforms. Process Dynamics and Control
Solution of ODEs using Laplace Transforms Process Dynamics and Control 1 Linear ODEs For linear ODEs, we can solve without integrating by using Laplace transforms Integrate out time and transform to Laplace
Digital Signal Processing Module 1 Analysis of Discrete time Linear Time - Invariant Systems
Digital Signal Processing Module 1 Analysis of Discrete time Linear Time - Invariant Systems Objective: 1. To understand the representation of Discrete time signals 2. To analyze the causality and stability
Discrete-Time Signals: Time-Domain Representation
Discrete-Time Signals: Time-Domain Representation 1 Signals represented as sequences of numbers, called samples Sample value of a typical signal or sequence denoted as x[n] with n being an integer in the
Signal Processing and Linear Systems1 Lecture 4: Characterizing Systems
Signal Processing and Linear Systems Lecture : Characterizing Systems Nicholas Dwork www.stanford.edu/~ndwork Our goal will be to develop a way to learn how the system behaves. In general, this is a very
Unit 2: Modeling in the Frequency Domain Part 2: The Laplace Transform. The Laplace Transform. The need for Laplace
Unit : Modeling in the Frequency Domain Part : Engineering 81: Control Systems I Faculty of Engineering & Applied Science Memorial University of Newfoundland January 1, 010 1 Pair Table Unit, Part : Unit,
1 Signals and systems
978--52-5688-4 - Introduction to Orthogonal Transforms: With Applications in Data Processing and Analysis Signals and systems In the first two chapters we will consider some basic concepts and ideas as
SIGNALS AND SYSTEMS. Unit IV. Analysis of DT signals
SIGNALS AND SYSTEMS Unit IV Analysis of DT signals Contents: 4.1 Discrete Time Fourier Transform 4.2 Discrete Fourier Transform 4.3 Z Transform 4.4 Properties of Z Transform 4.5 Relationship between Z
) = nlog b ( m) ( m) log b ( ) ( ) = log a b ( ) Algebra 2 (1) Semester 2. Exponents and Logarithmic Functions
Exponents and Logarithmic Functions Algebra 2 (1) Semester 2! a. Graph exponential growth functions!!!!!! [7.1]!! - y = ab x for b > 0!! - y = ab x h + k for b > 0!! - exponential growth models:! y = a(
Networks and Systems Prof V.G K. Murti Department of Electrical Engineering Indian Institute of Technology, Madras Lecture - 10 Fourier Series (10)
Networks and Systems Prof V.G K. Murti Department of Electrical Engineering Indian Institute of Technology, Madras Lecture - 10 Fourier Series (10) What we have seen in the previous lectures, is first
16.362: Signals and Systems: 1.0
16.362: Signals and Systems: 1.0 Prof. K. Chandra ECE, UMASS Lowell September 1, 2016 1 Background The pre-requisites for this course are Calculus II and Differential Equations. A basic understanding of
ENSC327 Communications Systems 2: Fourier Representations. Jie Liang School of Engineering Science Simon Fraser University
ENSC327 Communications Systems 2: Fourier Representations Jie Liang School of Engineering Science Simon Fraser University 1 Outline Chap 2.1 2.5: Signal Classifications Fourier Transform Dirac Delta Function
Signals and Systems Lecture Notes
Dr. Mahmoud M. Al-Husari Signals and Systems Lecture Notes This set of lecture notes are never to be considered as a substitute to the textbook recommended by the lecturer. ii Contents Preface v 1 Introduction
PUTNAM PROBLEMS SEQUENCES, SERIES AND RECURRENCES. Notes
PUTNAM PROBLEMS SEQUENCES, SERIES AND RECURRENCES Notes. x n+ = ax n has the general solution x n = x a n. 2. x n+ = x n + b has the general solution x n = x + (n )b. 3. x n+ = ax n + b (with a ) can be
Discrete-time Fourier transform (DTFT) representation of DT aperiodic signals Section The (DT) Fourier transform (or spectrum) of x[n] is
![Discrete-time Fourier transform (DTFT) representation of DT aperiodic signals Section The (DT) Fourier transform (or spectrum) of x[n] is](/thumbs/89/98498368.jpg "Discrete-time Fourier transform (DTFT) representation of DT aperiodic signals Section The (DT) Fourier transform (or spectrum) of x[n] is")
Discrete-time Fourier transform (DTFT) representation of DT aperiodic signals Section 5. 3 The (DT) Fourier transform (or spectrum) of x[n] is X ( e jω) = n= x[n]e jωn x[n] can be reconstructed from its
Chapter 4 The Fourier Series and Fourier Transform
Chapter 4 The Fourier Series and Fourier Transform Representation of Signals in Terms of Frequency Components Consider the CT signal defined by N xt () = Acos( ω t+ θ ), t k = 1 k k k The frequencies `present
Digital Signal Octave Codes (0A)
Digital Signal Periodic Conditions Copyright (c) 2009-2017 Young W. Lim. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version
Discrete-time Signals and Systems in
Discrete-time Signals and Systems in the Frequency Domain Chapter 3, Sections 3.1-39 3.9 Chapter 4, Sections 4.8-4.9 Dr. Iyad Jafar Outline Introduction The Continuous-Time FourierTransform (CTFT) The
X. Chen More on Sampling
X. Chen More on Sampling 9 More on Sampling 9.1 Notations denotes the sampling time in second. Ω s = 2π/ and Ω s /2 are, respectively, the sampling frequency and Nyquist frequency in rad/sec. Ω and ω denote,
Digital Signal Octave Codes (0A)
Digital Signal Periodic Conditions Copyright (c) 2009-207 Young W. Lim. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version.2
Chapter 8 The Discrete Fourier Transform
Chapter 8 The Discrete Fourier Transform Introduction Representation of periodic sequences: the discrete Fourier series Properties of the DFS The Fourier transform of periodic signals Sampling the Fourier
The Discrete-Time Fourier
Chapter 3 The Discrete-Time Fourier Transform 清大電機系林嘉文 cwlin@ee.nthu.edu.tw 03-5731152 Original PowerPoint slides prepared by S. K. Mitra 3-1-1 Continuous-Time Fourier Transform Definition The CTFT of
Section 4.1: Sequences and Series
Section 4.1: Sequences and Series In this section, we shall introduce the idea of sequences and series as a necessary tool to develop the proof technique called mathematical induction. Most of the material
06EC44-Signals and System Chapter Fourier Representation for four Signal Classes
Chapter 5.1 Fourier Representation for four Signal Classes 5.1.1Mathematical Development of Fourier Transform If the period is stretched without limit, the periodic signal no longer remains periodic but
Infinite Series. MATH 211, Calculus II. J. Robert Buchanan. Spring Department of Mathematics
Infinite Series MATH 211, Calculus II J. Robert Buchanan Department of Mathematics Spring 2018 Background Consider the repeating decimal form of 2/3. 2 3 = 0.666666 = 0.6 + 0.06 + 0.006 + 0.0006 + = 6(0.1)
Digital Signal Octave Codes (0A)
Digital Signal Periodic Conditions Copyright (c) 2009-2017 Young W. Lim. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version
EE482: Digital Signal Processing Applications
Professor Brendan Morris, SEB 3216, brendan.morris@unlv.edu EE482: Digital Signal Processing Applications Spring 2014 TTh 14:30-15:45 CBC C222 Lecture 02 DSP Fundamentals 14/01/21 http://www.ee.unlv.edu/~b1morris/ee482/
Automatic Control Systems theory overview (discrete time systems)
Automatic Control Systems theory overview (discrete time systems) Prof. Luca Bascetta (luca.bascetta@polimi.it) Politecnico di Milano Dipartimento di Elettronica, Informazione e Bioingegneria Motivations
Laplace Transforms Chapter 3
Laplace Transforms Important analytical method for solving linear ordinary differential equations. - Application to nonlinear ODEs? Must linearize first. Laplace transforms play a key role in important
Digital Signal Octave Codes (0A)
Digital Signal Periodic Conditions Copyright (c) 2009-207 Young W. Lim. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version.2
Digital Signal Octave Codes (0A)
Digital Signal Periodic Conditions Copyright (c) 2009-207 Young W. Lim. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version.2
Chapter 4 Discrete Fourier Transform (DFT) And Signal Spectrum
Chapter 4 Discrete Fourier Transform (DFT) And Signal Spectrum CEN352, DR. Nassim Ammour, King Saud University 1 Fourier Transform History Born 21 March 1768 ( Auxerre ). Died 16 May 1830 ( Paris ) French
Topic 3: Fourier Series (FS)
ELEC264: Signals And Systems Topic 3: Fourier Series (FS) o o o o Introduction to frequency analysis of signals CT FS Fourier series of CT periodic signals Signal Symmetry and CT Fourier Series Properties
Chapter Generating Functions
Chapter 8.1.1-8.1.2. Generating Functions Prof. Tesler Math 184A Fall 2017 Prof. Tesler Ch. 8. Generating Functions Math 184A / Fall 2017 1 / 63 Ordinary Generating Functions (OGF) Let a n (n = 0, 1,...)
Discrete-Time Signals & Systems
Chapter 2 Discrete-Time Signals & Systems 清大電機系林嘉文 cwlin@ee.nthu.edu.tw 03-5731152 Original PowerPoint slides prepared by S. K. Mitra 2-1-1 Discrete-Time Signals: Time-Domain Representation (1/10) Signals
Continuous and Discrete Time Signals and Systems
Continuous and Discrete Time Signals and Systems Mrinal Mandal University of Alberta, Edmonton, Canada and Amir Asif York University, Toronto, Canada CAMBRIDGE UNIVERSITY PRESS Contents Preface Parti Introduction
Let H(z) = P(z)/Q(z) be the system function of a rational form. Let us represent both P(z) and Q(z) as polynomials of z (not z -1 )
Review: Poles and Zeros of Fractional Form Let H() = P()/Q() be the system function of a rational form. Let us represent both P() and Q() as polynomials of (not - ) Then Poles: the roots of Q()=0 Zeros:
Introduction to DSP Time Domain Representation of Signals and Systems
Introduction to DSP Time Domain Representation of Signals and Systems Dr. Waleed Al-Hanafy waleed alhanafy@yahoo.com Faculty of Electronic Engineering, Menoufia Univ., Egypt Digital Signal Processing (ECE407)
Digital Signal Octave Codes (0A)
Digital Signal Periodic Conditions Copyright (c) 2009-207 Young W. Lim. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version.2
Digital Signal Processing
Digital Signal Processing The -Transform and Its Application to the Analysis of LTI Systems Moslem Amiri, Václav Přenosil Embedded Systems Laboratory Faculty of Informatics, Masaryk University Brno, Cech
Solutions to Assignment 1
Solutions to Assignment 1 Question 1. [Exercises 1.1, # 6] Use the division algorithm to prove that every odd integer is either of the form 4k + 1 or of the form 4k + 3 for some integer k. For each positive
Summary of Fourier Transform Properties
Summary of Fourier ransform Properties Frank R. Kschischang he Edward S. Rogers Sr. Department of Electrical and Computer Engineering University of oronto January 7, 207 Definition and Some echnicalities
DETERMINANTS 1. def. (ijk) = (ik)(ij).
DETERMINANTS 1 Cyclic permutations. A permutation is a one-to-one mapping of a set onto itself. A cyclic permutation, or a cycle, or a k-cycle, where k 2 is an integer, is a permutation σ where for some
4.1. If the input of the system consists of the superposition of M functions, M
4. The Zero-State Response: The system state refers to all information required at a point in time in order that a unique solution for the future output can be compute from the input. In the case of LTIC
2 Problem Set 2 Graphical Analysis
2 PROBLEM SET 2 GRAPHICAL ANALYSIS 2 Problem Set 2 Graphical Analysis 1. Use graphical analysis to describe all orbits of the functions below. Also draw their phase portraits. (a) F(x) = 2x There is only
Control Systems I. Lecture 6: Poles and Zeros. Readings: Emilio Frazzoli. Institute for Dynamic Systems and Control D-MAVT ETH Zürich
Control Systems I Lecture 6: Poles and Zeros Readings: Emilio Frazzoli Institute for Dynamic Systems and Control D-MAVT ETH Zürich October 27, 2017 E. Frazzoli (ETH) Lecture 6: Control Systems I 27/10/2017
Introduction to Signal Spaces
Introduction to Signal Spaces Selin Aviyente Department of Electrical and Computer Engineering Michigan State University January 12, 2010 Motivation Outline 1 Motivation 2 Vector Space 3 Inner Product
Digital Signal Processing
Digital Signal Processing Introduction Moslem Amiri, Václav Přenosil Embedded Systems Laboratory Faculty of Informatics, Masaryk University Brno, Czech Republic amiri@mail.muni.cz prenosil@fi.muni.cz February
ICS141: Discrete Mathematics for Computer Science I
ICS4: Discrete Mathematics for Computer Science I Dept. Information & Computer Sci., Jan Stelovsky based on slides by Dr. Baek and Dr. Still Originals by Dr. M. P. Frank and Dr. J.L. Gross Provided by
FOURIER TRANSFORMS. At, is sometimes taken as 0.5 or it may not have any specific value. Shifting at
Chapter 2 FOURIER TRANSFORMS 2.1 Introduction The Fourier series expresses any periodic function into a sum of sinusoids. The Fourier transform is the extension of this idea to non-periodic functions by
Discrete Time Signals and Systems Time-frequency Analysis. Gloria Menegaz
Discrete Time Signals and Systems Time-frequency Analysis Gloria Menegaz Time-frequency Analysis Fourier transform (1D and 2D) Reference textbook: Discrete time signal processing, A.W. Oppenheim and R.W.
Chapter 10. Infinite Sequences and Series
10.6 Alternating Series, Absolute and Conditional Convergence 1 Chapter 10. Infinite Sequences and Series 10.6 Alternating Series, Absolute and Conditional Convergence Note. The convergence tests investigated
The Laplace Transform
The Laplace Transform Introduction There are two common approaches to the developing and understanding the Laplace transform It can be viewed as a generalization of the CTFT to include some signals with
LINEAR SYSTEMS. J. Elder PSYC 6256 Principles of Neural Coding
LINEAR SYSTEMS Linear Systems 2 Neural coding and cognitive neuroscience in general concerns input-output relationships. Inputs Light intensity Pre-synaptic action potentials Number of items in display
The Fourier Transform (and more )
The Fourier Transform (and more ) imrod Peleg ov. 5 Outline Introduce Fourier series and transforms Introduce Discrete Time Fourier Transforms, (DTFT) Introduce Discrete Fourier Transforms (DFT) Consider
Power series solutions for 2nd order linear ODE s (not necessarily with constant coefficients) a n z n. n=0
Lecture 22 Power series solutions for 2nd order linear ODE s (not necessarily with constant coefficients) Recall a few facts about power series: a n z n This series in z is centered at z 0. Here z can
PROBLEMS ON CONGRUENCES AND DIVISIBILITY
PROBLEMS ON CONGRUENCES AND DIVISIBILITY 1. Do there exist 1,000,000 consecutive integers each of which contains a repeated prime factor? 2. A positive integer n is powerful if for every prime p dividing
s=a+jb s=% x(t)=sin(&t)
Linearity input Ax (t)+bx (t) Time invariance x(t-$) x(t) Characteristic Functions Linear Time Invariant Systems Linear Time Invariant System scaling & superposition e st complex exponentials y(t) output
GATE EE Topic wise Questions SIGNALS & SYSTEMS
www.gatehelp.com GATE EE Topic wise Questions YEAR 010 ONE MARK Question. 1 For the system /( s + 1), the approximate time taken for a step response to reach 98% of the final value is (A) 1 s (B) s (C)
Radar Systems Engineering Lecture 3 Review of Signals, Systems and Digital Signal Processing
Radar Systems Engineering Lecture Review of Signals, Systems and Digital Signal Processing Dr. Robert M. O Donnell Guest Lecturer Radar Systems Course Review Signals, Systems & DSP // Block Diagram of
Outline of the Seminar Topics on elliptic curves Saarbrücken,
Outline of the Seminar Topics on elliptic curves Saarbrücken, 11.09.2017 Contents A Number theory and algebraic geometry 2 B Elliptic curves 2 1 Rational points on elliptic curves (Mordell s Theorem) 5
Laboratory handouts, ME 340
Laboratory handouts, ME 340 This document contains summary theory, solved exercises, prelab assignments, lab instructions, and report assignments for Lab 4. 2014-2016 Harry Dankowicz, unless otherwise
Discrete-Time Signals and Systems. The z-transform and Its Application. The Direct z-transform. Region of Convergence. Reference: Sections
Discrete-Time Signals and Systems The z-transform and Its Application Dr. Deepa Kundur University of Toronto Reference: Sections 3. - 3.4 of John G. Proakis and Dimitris G. Manolakis, Digital Signal Processing:
The z-transform Part 2
http://faculty.kfupm.edu.sa/ee/muqaibel/ The z-transform Part 2 Dr. Ali Hussein Muqaibel The material to be covered in this lecture is as follows: Properties of the z-transform Linearity Initial and final
SIGNALS AND SYSTEMS I. RAVI KUMAR
Signals and Systems SIGNALS AND SYSTEMS I. RAVI KUMAR Head Department of Electronics and Communication Engineering Sree Visvesvaraya Institute of Technology and Science Mahabubnagar, Andhra Pradesh New
Signals and Systems Laboratory with MATLAB
Signals and Systems Laboratory with MATLAB Alex Palamides Anastasia Veloni @ CRC Press Taylor &. Francis Group Boca Raton London NewYork CRC Press is an imprint of the Taylor & Francis Group, an informa
LECTURE NOTES DIGITAL SIGNAL PROCESSING III B.TECH II SEMESTER (JNTUK R 13)
LECTURE NOTES ON DIGITAL SIGNAL PROCESSING III B.TECH II SEMESTER (JNTUK R 13) FACULTY : B.V.S.RENUKA DEVI (Asst.Prof) / Dr. K. SRINIVASA RAO (Assoc. Prof) DEPARTMENT OF ELECTRONICS AND COMMUNICATIONS
Notes 07 largely plagiarized by %khc
Notes 07 largely plagiarized by %khc Warning This set of notes covers the Fourier transform. However, i probably won t talk about everything here in section; instead i will highlight important properties
LTI Systems (Continuous & Discrete) - Basics
LTI Systems (Continuous & Discrete) - Basics 1. A system with an input x(t) and output y(t) is described by the relation: y(t) = t. x(t). This system is (a) linear and time-invariant (b) linear and time-varying
SEISMIC WAVE PROPAGATION. Lecture 2: Fourier Analysis
SEISMIC WAVE PROPAGATION Lecture 2: Fourier Analysis Fourier Series & Fourier Transforms Fourier Series Review of trigonometric identities Analysing the square wave Fourier Transform Transforms of some
CHAPTER 1 REAL NUMBERS KEY POINTS
CHAPTER 1 REAL NUMBERS 1. Euclid s division lemma : KEY POINTS For given positive integers a and b there exist unique whole numbers q and r satisfying the relation a = bq + r, 0 r < b. 2. Euclid s division
MAS.160 / MAS.510 / MAS.511 Signals, Systems and Information for Media Technology Fall 2007
MIT OpenCourseWare http://ocw.mit.edu MAS.60 / MAS.50 / MAS.5 Signals, Systems and Information for Media Technology Fall 007 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms.
Some of the different forms of a signal, obtained by transformations, are shown in the figure. jwt e z. jwt z e
Transform methods Some of the different forms of a signal, obtained by transformations, are shown in the figure. X(s) X(t) L - L F - F jw s s jw X(jw) X*(t) F - F X*(jw) jwt e z jwt z e X(nT) Z - Z X(z)
Notes on Continued Fractions for Math 4400
. Continued fractions. Notes on Continued Fractions for Math 4400 The continued fraction expansion converts a positive real number α into a sequence of natural numbers. Conversely, a sequence of natural
Communication Systems. Collection Editor: Janko Calic
Communication Systems Collection Editor: Janko Calic Communication Systems Collection Editor: Janko Calic Authors: Thanos Antoulas Richard Baraniuk Dan Calderon Catherine Elder Anders Gjendemsjø Michael
Signals & Systems Handout #4
Signals & Systems Handout #4 H-4. Elementary Discrete-Domain Functions (Sequences): Discrete-domain functions are defined for n Z. H-4.. Sequence Notation: We use the following notation to indicate the