Block Diagram 1 REG. VCC 2 Hall Plate Amp B 3 GND 4 Pin Assignment 277 (276) Front View 1 : VCC 2 : 3 : B :GND Name P/I/O Pin # Desc
|
|
- Hannah Bryan
- 5 years ago
- Views:
Transcription
1 Features - On-chip Hall sensor with two different sensitivity and hysteresis settings for - 3.5V to 2V operating voltage - 4mA (avg) output sink current - Build-in protecting diode only for chip reverse power connecting - -2 C to 85 C operating temperature - Low profile 4 pin SIP package Applications - Dual-coil Brush-less DC Motor - Dual-coil Brush-less DC Fan - Revolution Counting - Speed Measurement General Description are integrated Hall sensors with output drivers, mainly designed for electronic commutation of brush-less DC Fan. This IC internally includes the regulator, protecting diode, Hall plate, amplifier, comparator, and a pair of complementary open-collector outputs (, B). While the magnetic flux density (B) is larger than operate point (), will turn on (low), and meanwhile B will turn off (high). Each output is latched until B is lower than release point (), and then B transfer each state. For DC fan application, sometimes need to test power reverse connection condition. Internal diode only protects chip-side but not for coil-side. If necessary, add one external diode to block the reverse current from coil-side. Ordering Information ATS27X X -XX X -X Part No. Wafer Body Package Lead Packing Magnetic Characteristics 6 : ATS276 Blank or P: SIP-4L L : Lead Free Blank : Tube or Bulk 276:A or B or C 7 : A~Z : if necessary to specify Blank: Normal A : Tape & Reel 277:A or B Typical Application Circuit 27X coil1 coil Brush-less DC Fan This datasheet contains new product information. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of this product. No rights under any patent accompany the sale of the product. Rev.B1 Mar 17, 24 1/7
2 Block Diagram 1 REG. VCC 2 Hall Plate Amp B 3 GND 4 Pin Assignment 277 (276) Front View 1 : VCC 2 : 3 : B :GND Name P/I/O Pin # Description P 1 Power Supply Input O 2 Output Pin B O 3 Output Pin GND P 4 Ground 2/7
3 Absolute Maximum Ratings ( at Ta=25 C ) Characteristics Symbol Values Unit Supply voltage V CC 2 V Reverse V CC Polarity Voltage V RCC -2 V Magnetic flux density B Unlimited Continuous.4 Output on current Hold Ic.5 A Peak (Start Up).7 Operating temperature range Ta -2~+85 C Storage temperature range Ts -65~+15 C Package Power Dissipation PD 55 mw Maximum Junction Temp Tj 15 C Electrical Characteristics ( T=+25 C = 4.V to 2V ) Characteristic Symbol Conditions Min Typ Max Units Low Supply Voltage Vce =3.5V, I L =1mA.4 V Supply Voltage V Output Zener Breakdown Vz 46 V Output Saturation Voltage Vce(sat) =14V, I L =3mA.3.6 V Output Leakage Current Icex Vce=14V, =14V <.1 1 µa Supply Current Icc =2V, Output Open ma Output Rise Time tr =14V, R L =82Ω, C L =2pF 3. 1 µs Output Falling Time tf =14V, R L =82Ω, C L =2pF µs Switch Time Differential t =14V, R L =82Ω, C L =2pF 3. 1 µs Test Circuit 14V 277 (276) RL1 RL2 RL1=RL2=82 Ohm CL1=CL2=2 pf CL1 CL2 B 3/7
4 Magnetic Characteristics( Ta=+25 C) (1mT=1 ) A grade Characteristic Symbol Min. Typ. Max. Unit Operate Point ATS Release Point ATS Hysteresis ATS B grade Characteristic Symbol Min. Typ. Max. Unit Operate Point ATS Release Point ATS Hysteresis ATS C grade Characteristic Symbol Min. Typ. Max. Unit Operate Point ATS Release Point ATS Hysteresis ATS B ( Output Voltage ) Turn off ( off-state ) Turn on ( Output Voltage ) Turn on ( off-state ) Turn off ( on-state ) Vsat ( Magnetic flux density B ) ( on-state ) Vsat ( Magnetic flux density B ) 4/7
5 Performance Characteristics (SIP4) Ta ( C) Pd (mw) Pd (mw) 1 Power Dissipation Curve Ta ( C) Typical Magnetic Switch Point VS. Supply Voltage Flux Density (G) Supply Voltage (V) s Typical Supply Current versus Supply Voltage Supply Current (ma) TA=8 o C TA=25 o C TA=-2 o C Supply Voltage (V) 5/7
6 Operating Characteristics S N ( SIP4 ) Marking side ( Output Voltage ) N Vsat High Vd Low S ( Magnetic flux density ) Marking Information Part Number ( Top View ) 27X X XX X X Blank : normal L : Lead Free Package ID Code: A ~ Z Nth week: 1~52 Year: "1" = 21 "2" = 22 ~ 6/7
7 Package Information Active Area Depth Marking side Package Sensor Location 1.75mm 1.35mm.7mm Package Dimension 1.55mm +/-.1mm 1.3mm +/-.1 5 o -7 o o 3 o mm +/-1.25mm.38mm +/-.3mm.3mm +/-.1mm 3.65mm +/-.1mm.46mm +/-.3mm.38mm +/-.3mm 5.22mm +/-.1mm 4.2mm +/-.1mm 27X 3.81mm +/-.3mm 5 o -7 o o 3 o -5.2mm Max. 1.42mm+/-.1mm 1.27mm +/-.3mm 7/7
General Description DTS27X X -X X X -X. Lead. 27X coil1. R1 = R2 = 470Ω C1 = C2 = 2.2 μ F The R, C value need to be fine tuned base on coils design.
Features - On-chip Hall sensor with two different sensitivity and hysteresis settings for - 3.5V to 18V operating voltage - 35mA (avg) output sink current - Built-in protecting diode only for chip reverse
More informationATS276 X - P X - B - X. Lead Free L : Lead Free G : Green
Features General Description On-Chip Hall Sensor with Two Different Sensitivity and Hysteresis Settings for ATS276 3.5V to 2V Operating Voltage 4mA (avg.) Output Sink Current Built-in Protecting Diode
More informationATS177. General Description. Features. Applications. Ordering Information SINGLE OUTPUT HALL EFFECT LATCH ATS177 - P L - X - X
Features General Description 3.5V to 20V DC operation voltage Temperature compensation Wide operating voltage range Open-Collector pre-driver 25mA maximum sinking output current Reverse polarity protection
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD COMPLEMENTARY OUTPUT HALL EFFECT LATCH DESCRIPTION The UTC H654 is integrated Hall sensors with complementary output drivers designed for electronic commutation of brushless
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD COMPLEMENTARY OUTPUTS HALL EFFECT LATCH IC DESCRIPTION The UTC UH277 is a Latch-Type Hall Effect sensor with built-in complementary output drivers. It s designed with internal
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD COMPLEMENTARY OUTPUTS HALL EFFECT LATCH IC DESCRIPTION The UTC UH276 is a Latch-Type Hall Effect sensor with built-in complementary output drivers. It s designed with internal
More informationHIGH VOLTAGE HALL EFFECT LATCH General Description. Features. Applications
General Description The is an integrated Hall sensor with output driver designed for electronic commutation of brushless DC motor applications. The device includes an onchip Hall sensor for magnetic sensing,
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD BIPOLAR LATCH TYPE HALL EFFECT FOR HIGH-TEMPERATURE OPERATION DESCRIPTION 1 SIP-3 The UTC SK1816 is a semiconductor integrated circuit utilizing the Hall effect. It designed
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD BIPOLAR LATCH TYPE HALL EFFECT FOR HIGH-TEMPERATURE OPERATION DESCRIPTION 1 SIP-3 The UTC SK1816 is a semiconductor integrated circuit utilizing the Hall effect. It designed
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD BIPOLAR LATCH TYPE HALL EFFECT FOR HIGH-TEMPERATURE OPERATION DESCRIPTION The UTC SK1816 is a semiconductor integrated circuit utilizing the Hall effect. It designed to operate
More informationHallogic Hall-Effect Sensors OH090U, OH180U, OH360U OHN3000 series, OHS3000 series OHN3100 series, OHS3100 series
Hallogic HallEffect Sensors OH9U, OH18U, OH36U OHN3 series, OHS3 series OHN3 series, OHS3 series Features: Designed for noncontact switching operations Operates over broad range of supply voltages (4.5
More informationHigh Reliability Hallogic Hall- Effect Sensors OMH090, OMH3019, OMH3020, OMH3040, OMH3075, OMH3131 (B, S versions)
High Reliability Hallogic Hall Features: Designed for noncontact switching operations Operates over a broad range of supply voltages Excellent temperature stability operates in harsh environments Suitable
More informationHallogic Hall-effect Sensors OH090U, OH180U, OH360U OHN3000 Series, OHS3000 Series OHN3100 Series, OHS3100 Series
Hallogic Halleffect Sensors Features: Designed for noncontact switching operations Operates over broad range of supply voltages (4.5 V to 24 V) Operates with excellent temperature stability in harsh environments
More informationChopper-Stabilized, Two Wire Hall-Effect Switches
FEATURES AND BENEFITS High speed, 4-phase chopper stabilization Low switchpoint drift throughout temperature range Low sensitivity to thermal and mechanical stresses On-chip protection Supply transient
More information4-PIN PHOTOTRANSISTOR OPTOCOUPLERS
PACKAGE HAA84 SCHEMATIC 4 COLLECTOR 4 2 3 EMITTER DESCRIPTION The HAA84 Series consists of two gallium arsenide infrared emitting diodes, connected in inverse parallel, driving a single silicon phototransistor
More informationMT3451 Series BiCMOS, Latch, Hall-Effect Magnetic Position Sensors
Features and Benefits BiCMOS Technology Magnetic Type: Latch Wide Operating Voltage Range: Supply Voltage 2.8~24V Specified Operating Temperature Range: From -40 ~ 150 High Magnetic Sensitivity B OP =20Gauss,
More informationGENERAL PURPOSE 6-PIN PHOTOTRANSISTOR OPTOCOUPLERS
4N37 HA HA2 HA3 HA4 HA5 WHITE PACKAGE (-M SUFFIX) SCHEMATIC 2 3 NC PIN. ANODE 2. CATHODE 3. NO CONNECTION 4. EMITTER 5. COLLECTOR. BASE 5 4 BLACK PACKAGE (NO -M SUFFIX) DESCRIPTION The general purpose
More information4-PIN PHOTOTRANSISTOR OPTOCOUPLERS
PACKAGE HAA84 SCHEMATIC 4 COLLECTOR 4 2 3 EMITTER DESCRIPTION The HAA84 Series consists of two gallium arsenide infrared emitting diodes, connected in inverse parallel, driving a single silicon phototransistor
More informationDiscontinued Product
Discontinued Product This device is no longer in production. The device should not be purchased for new design applications. Samples are no longer available. Date of status change: November 1, 21 Recommended
More informationGENERAL PURPOSE 6-PIN PHOTOTRANSISTOR OPTOCOUPLERS
TIL TIL-M TIL7-M MOC800-M WHITE PACKAGE (-M SUFFIX) SCHEMATIC 2 3 NC 5 4 PIN. ANODE 2. CATHODE 3. NO CONNECTION 4. EMITTER 5. COLLECTOR. BASE BLACK PACKAGE (NO -M SUFFIX) DESCRIPTION The MOC800, TIL and
More informationPHOTOTRANSISTOR OPTOCOUPLERS
MCT MCTE MCT0 MCT7 MCT00 MCT0 MCT0 WHITE PACKAGE (-M SUFFIX) BLACK PACKAGE (NO -M SUFFIX) DESCRIPTION The MCTXXX series optoisolators consist of a gallium arsenide infrared emitting diode driving a silicon
More informationH21A1 / H21A2 / H21A3 PHOTOTRANSISTOR OPTICAL INTERRUPTER SWITCH
HA / HA / HA.07 (.85). (.8) NOTES: 0.9 (6.5) 0. (6.5) 0.5 (.) 0.9 (.0) PACKAGE DIMENSIONS.95 (7.5).7 (6.9) 0.97 (.7) 0.957 (.) 0.7 (.0) 0.57 (.6) D E 0.755 (9.) 0.75 (8.9) 0.9 (.) 0.9 (.0) Ø 0. (.) Ø 0.6
More informationMOC205-M MOC206-M MOC207-M MOC208-M
DESCRIPTION These devices consist of a gallium arsenide infrared emitting diode optically coupled to a monolithic silicon phototransistor detector, in a surface mountable, small outline, plastic package.
More informationMT4106 Series Uni-polar, Hall-Effect
Uni-polar, Hall-Effect Magnetic Position ensors Features and Benefits Bipolar Technology Magnetic Type: Uni-polar Wide Operating Voltage Range: upply Voltage 3.8~30V pecified Operating Temperature Range:
More informationHAL501...HAL506, HAL508 Hall Effect Sensor ICs MICRONAS INTERMETALL MICRONAS. Edition May 5, DS
MICRONAS INTERMETALL HAL1...HAL, HAL Hall Effect Sensor ICs Edition May, 1997 1--1DS MICRONAS HAL1...HAL HAL Hall Effect Sensor IC in CMOS technology Common Features: switching offset compensation at khz
More informationContinuous-Time Switch Family
Features and enefits Continuous-time operation Fast power-on time Low noise Stable operation over full operating temperature range Reverse battery protection Solid-state reliability Factory-programmed
More informationS-57K1 A Series FOR AUTOMOTIVE 125 C OPERATION HIGH-WITHSTAND VOLTAGE HIGH-SPEED BIPOLAR HALL EFFECT LATCH IC. Features. Applications.
www.ablic.com FOR AUTOMOTIVE 125 C OPERATION HIGH-WITHSTAND VOLTAGE HIGH-SPEED BIPOLAR HALL EFFECT LATCH IC ABLIC Inc., 2013-2019 This IC, developed by CMOS technology, is a high-accuracy Hall effect latch
More information4N25 4N26 4N27 4N28. MAXIMUM RATINGS (TA = 25 C unless otherwise noted) SCHEMATIC. Order this document by 4N25/D STANDARD THRU HOLE
Order this document by N/D GlobalOptoisolator The N, N, N7 and N8 devices consist of a gallium arsenide infrared emitting diode optically coupled to a monolithic silicon phototransistor detector. Most
More informationFeatures. Description. Table 1. Device summary. Order code Marking Packages Packing. STGD19N40LZ GD19N40LZ DPAK Tape and reel
Automotive-grade 390 V internally clamped IGBT E SCIS 180 mj Features Datasheet - production data TAB DPAK 1 3 AEC-Q101 qualified 180 mj of avalanche energy @ T C = 150 C, L = 3 mh ESD gate-emitter protection
More informationOptical (2.8) (2.3) PIN 1 ANODE PIN 2 CATHODE PIN 3 COLLECTOR PIN 4 EMITTER
PACKAGE DIMENSIONS 0.97 (.7) 0.957 (.3) 0.7 (.0) 0.57 (.6) Ø 0.33 (3.) Ø 0.6 (3.) (X) 0.9 (6.35) 0.3 (6.5) D E 0.755 (9.) 0.75 (8.9) 0.39 (.00) 0.3 (0.85) 0.9 (3.3) 0.9 (3.0) 0.03 (.60) NOM 0.33 (.0) 0.
More informationA1245. Chopper-Stabilized, Two Wire Hall-Effect Latch PACKAGES
FEATURES AND BENEFITS High speed, 4-phase chopper stabilization Low switchpoint drift throughout temperature range Low sensitivity to thermal and mechanical stresses On-chip protection Supply transient
More informationA1244 Chopper-Stabilized, Two Wire Hall-Effect Latch
Features and Benefits High speed, 4-phase chopper stabilization Low switchpoint drift throughout temperature range Low sensitivity to thermal and mechanical stresses On-chip protection Supply transient
More informationInsulated Gate Bipolar Transistor (IGBT)
BUK856-8A GENERAL DESCRIPTION QUICK REFERENCE DATA Fast-switching N-channel insulated SYMBOL PARAMETER MAX. UNIT gate bipolar power transistor in a plastic envelope. V CE Collector-emitter voltage 8 V
More informationAlfa-MOS Technology. AF V / 50mA Linear LED Driver
General Description The is a linear LED driver. The application of high bright LED is widely used for general illumination. The maximum output current is 50mA. Typical variations is % in V IN = 6 ~ 500V
More informationAP Pin Assignments. Description. Features UNIVERSAL DC/DC CONVERTER AP34063 SO-8. PDIP-8 ( Top View ) ( Top View )
UNIVERSAL DC/DC CONVERTER Description Pin Assignments The Series is a monolithic control circuit containing the primary functions required for DC-to-DC converters. These devices consist of an internal
More informationAutomotive-grade 400 V internally clamped IGBT E SCIS 320 mj
STGB25N40LZAG, STGD25N40LZAG Datasheet Automotive-grade 400 V internally clamped IGBT E SCIS 320 mj Features TAB D 2 PAK 2 1 3 TAB 2 1 DPAK 3 AEC-Q101 qualified SCIS energy of 320 mj @ T J = 25 C Parts
More informationGM4275 GM4275 V2.03. Features. Description. Applications. Block Diagram WIDE INPUT RANGE 5V LOW DROPOUT REGULATOR WITH RESET FLAG
Description The GM4275 series of fixed output, micro-power voltage regulators is designed for applications which require wide input voltage range up to 45V. The GM4275 is an excellent choice for the use
More informationHall-Effect Latch / Bipolar Switch
2 - FEATURES AND BENEFITS AEC-Q1 automotive qualified Quality managed (QM), ISO 26262 compliant High-speed, 4-phase chopper stabilization Low operating voltage down to 3 V High sensitivity Stable switchpoints
More informationPH5504A2NA1. Ambient Light Sensor DESCRIPTION FEATURES APPLICATIONS. R08DS0067EJ0100 Rev.1.00 Nov 05, 2012 DISCONTINUED
Ambient Light Sensor DESCRIPTION Data Sheet The is an ambient light sensor with a photo diode and current amplifier. This product has spectral characteristics close to human eye sensitivity and outputs
More informationMM74C00 MM74C02 MM74C04 Quad 2-Input NAND Gate Quad 2-Input NOR Gate Hex Inverter
MM74C00 MM74C02 MM74C04 Quad 2-Input NAND Gate Quad 2-Input NOR Gate Hex Inverter General Description The MM74C00, MM74C02, and MM74C04 logic gates employ complementary MOS (CMOS) to achieve wide power
More informationH11AV1-M H11AV1A-M H11AV2-M H11AV2A-M
PACKAGE OUTLINE SCHEMATIC 6 6 HAVS-M, HAV2S-M 6 HAV-M, HAV2-M 2 3 NC PIN. ANODE 2. CATHODE 3. NO CONNECTION 4. EMITTER 5. COLLECTOR 6. BASE 5 4 6 HAVA-M, HAV2A-M DESCRIPTION The general purpose optocouplers
More informationPHOTODARLINGTON OPTICAL INTERRUPTER SWITCH
HB HB HB3 PACKAGE DIMENSIONS 0.7 (.0) 0.57 (.6) C L 0.9 (6.35) 0.3 (6.5) D E C L 0.39 (.00) 0.3 (0.85).33 (3.38).073 (.85) 0.9 (3.3) 0.9 (3.0) 0.33 (.0) 0. (0.7) Optical C L 0.5 (3.) 0.9 (3.0).35 (8.00).95
More informationMM74C00 MM74C02 MM74C04 Quad 2-Input NAND Gate Quad 2-Input NOR Gate Hex Inverter
MM74C00 MM74C02 MM74C04 Quad 2-Input NAND Gate Quad 2-Input NOR Gate Hex Inverter General Description The MM74C00, MM74C02, and MM74C04 logic gates employ complementary MOS (CMOS) to achieve wide power
More informationS-57P1 S Series FOR AUTOMOTIVE 150 C OPERATION HIGH-WITHSTAND VOLTAGE HIGH-SPEED BIPOLAR HALL EFFECT LATCH IC. Features. Applications.
www.ablicinc.com FOR AUTOMOTIVE 150 C OPERATION HIGH-WITHSTAND VOLTAGE HIGH-SPEED BIPOLAR HALL EFFECT LATCH IC ABLIC Inc., 2015-2017 This IC, developed by CMOS technology, is a high-accuracy Hall effect
More informationMM74C373 MM74C374 3-STATE Octal D-Type Latch 3-STATE Octal D-Type Flip-Flop
MM74C374 3-STATE Octal D-Type Latch 3-STATE Octal D-Type Flip-Flop General Description The and MM74C374 are integrated, complementary MOS (CMOS), 8-bit storage elements with 3- STATE outputs. These outputs
More informationMOC8111 MOC8112 MOC8113
PACKAGE SCHEMATIC ANODE 6 N/C 6 6 CATHODE 2 5 COLLECTOR N/C 3 4 EMITTER 6 DESCRIPTION The MOC8X series consists of a Gallium Arsenide IRED coupled with an NPN phototransistor. The base of the transistor
More informationS-5743 A Series 125 C OPERATION HIGH-WITHSTAND VOLTAGE HIGH-SPEED BIPOLAR HALL EFFECT LATCH IC. Features. Applications. Package.
www.ablicinc.com S-5743 A Series 125 C OPERATION HIGH-WITHSTAND VOLTAGE HIGH-SPEED BIPOLAR HALL EFFECT LATCH IC ABLIC Inc., 2015-2017 Rev.1.1_02 This IC, developed by CMOS technology, is a high-accuracy
More informationDetection of S pole Detection of N pole Active "L" Active "H" Nch open-drain output Nch driver built-in pull-up resistor. f C = 250 khz typ.
www.ablic.com www.ablicinc.com S-5732 B Series 125 C OPERATION HIGH-WITHSTAND VOLTAGE HIGH-SPEED UNIPOLAR DETECTION TYPE HALL EFFECT SWITCH IC ABLIC Inc., 2016-2017 Rev.2.1_02 This IC, developed by CMOS
More informationNPN/PNP low V CEsat Breakthrough in Small Signal (BISS) transistor pair in a SOT457 (SC-74) Surface Mounted Device (SMD) plastic package.
Rev. 02 14 July 2005 Product data sheet 1. Product profile 1.1 General description NPN/PNP low V CEsat Breakthrough in Small Signal (BISS) transistor pair in a SOT457 (SC-74) Surface Mounted Device (SMD)
More informationIsolated Current Sensor with Common Mode Field Rejection
Fully Integrated Current Sensor IC Isolated Current Sensor with Common Mode Field Rejection Description The SENKO SC820 provides economical and precise solutions for AC or DC current sensing in industrial,
More informationMM74C14 Hex Schmitt Trigger
MM74C14 Hex Schmitt Trigger General Description The MM74C14 Hex Schmitt Trigger is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement transistors. The
More informationThe IK642B is a bi-polar integrated circuit designed for the wiper application in the automotive market. It includes wipe, wash and internal mode.
TECHNICAL DATA INTERAL- and WIPE/WASH WIPER CONTROL IC IK642B The IK642B is a bi-polar integrated circuit designed for the wiper application in the automotive market. It includes wipe, wash and internal
More informationA1126. Chopper-Stabilized Omnipolar Hall-Effect Switch DESCRIPTION FEATURES AND BENEFITS. PACKAGES: Not to scale. Functional Block Diagram
FEATURES AND BENEFITS AEC-Q1 automotive qualified Omnipolar operation Low switchpoint drift Superior temperature stability Insensitive to physical stress Reverse-battery protection Robust EMC capability
More informationRIGHT ANGLE SURFACE MOUNT INFRARED PHOTOTRANSISTOR
PACKAGE DIMENSIONS.16 (3.).11 (.8).43 (1.1).3 (.9) FRONT. (.).87 (.).71 (1.8).39 (1.).87 (.).71 (1.8) TOP.3 (.9) R.17 (.4) COLLECTOR MARK 1 NOTE:.16 (.4) BACK 1. Emitter. Collector 3. Tolerance of ±.1
More informationMM74C14 Hex Schmitt Trigger
MM74C14 Hex Schmitt Trigger General Description The MM74C14 Hex Schmitt Trigger is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement transistors. The
More informationNPN/PNP low V CEsat Breakthrough in Small Signal (BISS) transistor pair in a SOT457 (SC-74) Surface Mounted Device (SMD) plastic package.
Rev. 03 11 December 2009 Product data sheet 1. Product profile 1.1 General description NPN/PNP low V CEsat Breakthrough in Small Signal (BISS) transistor pair in a SOT457 (SC-74) Surface Mounted Device
More informationAPS12205, APS12215, and APS12235 High-Temperature Hall-Effect Latches for Low Voltage Applications
FEATURES AND BENEFITS Optimized for applications with regulated power rails Operation from to. V AEC-Q100 automotive qualified Operation up to 17 C junction temperature Dynamic offset cancellation Resistant
More informationAME, Inc. 5A Low Dropout AME1084 Positive Voltage Regulator General Description Functional Block Diagram Input Current Limiting
General Description Functional Block Diagram The is a 5A low-dropout positive voltage regulator. It is available in fixed and adjustable output voltage versions. Overcurrent and thermal protection are
More informationS-5841 Series TEMPERATURE SWITCH IC (THERMOSTAT IC) Features. Applications. Packages. Seiko Instruments Inc. 1.
S-5841 Series www.sii-ic.com Seiko Instruments Inc., 2007-2012 Rev.2.1_00 The S-5841 Series is a temperature switch IC (thermostat IC) which detects the temperature with a temperature accuracy of ±2.5
More informationAC INPUT/PHOTOTRANSISTOR OPTOCOUPLERS
HAA HAA3 HAA2 HAA4 DESCRIPTION The HAAX series consists of two gallium-arsenide infrared emitting diodes connected in inverse parallel driving a single silicon phototransistor output. FEATURES Bi-polar
More informationSilicon Diffused Darlington Power Transistor
GENERAL DESCRIPTION Highvoltage, monolithic npn power Darlington transistor in a SOT93 envelope intended for use in car ignition systems, DC and AC motor controls, solenoid drivers, etc. QUICK REFERENCE
More informationIRGB8B60KPbF IRGS8B60KPbF IRGSL8B60KPbF C
INSULATED GATE BIPOLAR TRANSISTOR Features Low VCE (on) Non Punch Through IGBT Technology. 1µs Short Circuit Capability. Square RBSOA. Positive VCE (on) Temperature Coefficient. Lead-Free. Benefits Benchmark
More informationHIGH SPEED-10 MBit/s LOGIC GATE OPTOCOUPLERS
DESCRIPTION The / optocouplers consist of an AlGaAS LED, optically coupled to a very high speed integrated photo-detector logic gate with a strobable output. The devices are housed in a compact small-outline
More informationTC74LCX08F,TC74LCX08FN,TC74LCX08FT,TC74LCX08FK
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74LCX08F/FN/FT/FK TC74LCX08F,TC74LCX08FN,TC74LCX08FT,TC74LCX08FK Low-Voltage Quad 2-Input AND Gate with 5-V Tolerant Inputs and Outputs The
More informationMP6901 MP6901. High Power Switching Applications. Hammer Drive, Pulse Motor Drive and Inductive Load Switching. Maximum Ratings (Ta = 25 C)
TOSHIBA Power Transistor Module Silicon Epitaxial Type (Darlington power transistor in ) High Power Switching Applications. Hammer Drive, Pulse Motor Drive and Inductive Load Switching. Industrial Applications
More informationContinuous-Time Switch Family
Features and Benefits Continuous-time operation Fast power-on time Low noise Stable operation over full operating temperature range Reverse battery protection Solid-state reliability Factory-programmed
More informationGT10Q301 GT10Q301. High Power Switching Applications Motor Control Applications. Maximum Ratings (Ta = 25 C) Equivalent Circuit. Marking
GTQ TOSHIBA Insulated Gate Bipolar Transistor Silicon N Channel IGBT GTQ High Power Switching Applications Motor Control Applications Unit: mm Third-generation IGBT Enhancement mode type High speed: tf
More informationIRGB30B60KPbF IRGS30B60KPbF IRGSL30B60KPbF
PD - 973 INSULATED GATE BIPOLAR TRANSISTOR Features Low VCE (on) Non Punch Through IGBT Technology 1µs Short Circuit Capability Square RBSOA G Positive VCE (on) Temperature Coefficient Maximum Junction
More information1200 V 600 A IGBT Module
1200 V 600 A IGBT RoHS Features Trench-gate field stop IGBT technology Low saturation voltage and positive temperature coefficient Fast switching and short tail current Free wheeling diodes with fast and
More informationChopper-Stabilized Precision Hall-Effect Latches
Features and Benefits AEC-Q1 automotive qualified Symmetrical latch switchpoints Resistant to physical stress Superior temperature stability Output short-circuit protection Operation from unregulated supply
More informationS-57M1 Series HIGH-SPEED BIPOLAR HALL EFFECT LATCH. Features. Applications. Package. ABLIC Inc., Rev.1.
www.ablic.com www.ablicinc.com HIGH-SPEED BIPOLAR HALL EFFECT LATCH ABLIC Inc., 2011-2013 Rev.1.2_02 The, developed by CMOS technology, is a high-accuracy Hall IC that operates with a high-sensitivity,
More informationTA7262P,TA7262P(LB),TA7262F
TOSHIBA BIPOLAR LINEAR INTEGRATED CIRCUIT SILICON MONOLITHIC TA7262P,TA7262P(LB),TA7262F DC MOTOR DRIVER (3 PHASE Bi DIRECTIONAL) The TA7262P / P (LB) / F are 3 Phase Bi Directional supply voltage control
More informationSGM7SZ00 Small Logic Two-Input NAND Gate
GENERAL DESCRIPTION The SGM7SZ00 is a single two-input NAND gate from SGMICRO s Small Logic series. The device is fabricated with advanced CMOS technology to achieve ultra-high speed with high output drive
More informationSilicon carbide Power MOSFET 650 V, 90 A, 18 mω (typ., T J = 25 C) in an H²PAK-7 package. Order code V DS R DS(on) max. I D
Datasheet Silicon carbide Power MOSFET 650 V, 90 A, 18 mω (typ., T J = 25 C) in an H²PAK-7 package TAB Features Order code V DS R DS(on) max. I D 1 H2PAK-7 7 SCTH90N65G2V-7 650 V 25 mω 90 A Very high operating
More informationMaintenance/ Discontinued
Cs for CD/CD-RM Player AN886SB 4ch. Linear Driver C for CD/CD-RM verview The AN886SB is a 4ch. driver using the power operational amplifier method. t employs the surface mounting type package superior
More informationMA8000 Series. [ Fine classification, H rank ] Silicon planer type MA111. Zener Diodes. For stabilization of power supply.
MA MA00 Series Silicon planer e For stabilization of power supply Unit : mm Features Extremely low noise voltage from the diode (.4V to 39V, /3 to / of our conventional MA00 series) Satisfactory in rise
More information5V/400mA Low Drop Voltage ILE4275 TECHNICAL DATA
TECHNICAL DATA 5V/400mA Low Drop Voltage ILE4275 is integrated circuits of voltage regulator 5V/400 ma with low-drop voltage. The IC of voltage regulator 5V/400 ma are purposed to supply DC voltage 5V
More informationSTGWA40HP65FB2. Trench gate field-stop, 650 V, 40 A, high-speed HB2 series IGBT in a TO-247 long leads package. Datasheet. Features.
Datasheet Trench gate field-stop, 65 V, 4 A, high-speed HB2 series IGBT in a TO-247 long leads package Features Maximum junction temperature : T J = 175 C Low V CE(sat) = 1.55 V(typ.) @ I C = 4 A Co-packaged
More informationPHOTODARLINGTON OPTOCOUPLERS
DESCRIPTION The CNX48U, HBX, and TIL3 have a gallium arsenide infrared emitter optically coupled to a silicon planar photodarlington. CNX48U HB HB2 HB255 HB3 TIL3 FEATURES High sensitivity to low input
More informationAPS13290 and APS13291 Precision Hall-Effect Latches for Consumer and Industrial Applications
APS329 and FEATURES AND BENEFITS Symmetrical latch switchpoints Superior ruggedness and fault tolerance Reverse-polarity and transient protection Operation from 4 C to 7 C junction temperature Output short-circuit
More informationS150PTD-1A. Technical Data Sheet. 3.2x1.6mm, Phototransistor LED Surface Mount Chip LED. Features: Descriptions: Applications:
Features: Fast response time. High photo sensitivity. Small junction capacitance. Package in 8mm tape on 7 diameter reel. The product itself will remain within RoHS compliant Version. Descriptions: The
More informationIRGS4062DPbF IRGSL4062DPbF
INSULATED GATE BIPOLAR TRANSISTOR WITH ULTRAFAST SOFT RECOVERY DIODE Features Low V CE (ON) Trench IGBT Technology Low switching losses Maximum Junction temperature 175 C 5 µs short circuit SOA Square
More informationHIGH SPEED TRANSISTOR OPTOCOUPLERS
SINGLECHANNEL: PACKAGE SCHEMATIC N/C V CC + V CC V F + V F 7 V B _ 7 V 0 _ V O _ V 0 V F N/C 4 5 GND + 4 5 GND,,, Pin 7 is not connected in Part Number / DESCRIPTION The /, / and / optocouplers consist
More information2 Input NAND Gate L74VHC1G00
Input NAND Gate The is an advanced high speed CMOS input NAND gate fabricated with silicon gate CMOS technology. It achieves high speed operation similar to equivalent Bipolar Schottky TTL while maintaining
More informationABLIC Inc., Rev.2.2_02
S-5841 Series www.ablicinc.com TEMPERATURE SWITCH IC (THERMOSTAT IC) ABLIC Inc., 2007-2015 Rev.2.2_02 The S-5841 Series is a temperature switch IC (thermostat IC) which detects the temperature with a temperature
More informationIsolated Current Sensor with Common Mode Field Rejection
Fully Integrated Current Sensor IC Isolated Current Sensor with Common Mode Field Rejection Description The Senko Micro s SC810 provides economical and precise solutions for AC or DC current sensing in
More informationAN8814SB. 4-channel driver IC for optical disk drive. ICs for Compact Disc/CD-ROM Player. Overview. Features. Applications.
AN884SB 4-channel driver IC for optical disk drive Overview The AN884SB is a BTL system 4-channel driver and is encapsulated in the SMD package which excels in heat radiation characteristic. 8.4±0. (5.5)
More informationIRGPS40B120UP INSULATED GATE BIPOLAR TRANSISTOR UltraFast IGBT
PD- 95899A IRGPS4B12UP INSULATED GATE BIPOLAR TRANSISTOR UltraFast IGBT Features Non Punch Through IGBT Technology. 1µs Short Circuit Capability. Square RBSOA. Positive VCE (on) Temperature Coefficient.
More informationIRGB4B60K IRGS4B60K IRGSL4B60K
INSULATED GATE BIPOLAR TRANSISTOR PD - 9633A IRGBB6K IRGSB6K IRGSLB6K Features Low VCE (on) Non Punch Through IGBT Technology. 1µs Short Circuit Capability. Square RBSOA. Positive VCE (on) Temperature
More informationMM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer
MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer General Description The MM74C150 and MM82C19 multiplex 16 digital lines to 1 output. A 4-bit address code determines
More information. HIGH SPEED .LOW POWER DISSIPATION .HIGH NOISE IMMUNITY M54HC4511 M74HC4511 BCD TO 7 SEGMENT LATCH/DECODER DRIVER. tpd = 28 ns (TYP.
M54HC4511 M74HC4511 BCD TO 7 SEGMENT LATCH/DECODER DRIVER. HIGH SPEED tpd = 28 (TYP.) AT VCC =5V.LOW POWER DISSIPATION I CC =4µA (MAX.) AT T A =25 C.HIGH NOISE IMMUNITY VNIH =VNIL =28%VCC (MIN.) OUTPUT
More informationSCT10N120. Silicon carbide Power MOSFET 1200 V, 12 A, 520 mω (typ., T J = 150 C) in an HiP247 package. Datasheet. Features. Applications.
Datasheet Silicon carbide Power MOSFET 12 V, 12 A, 52 mω (typ., T J = 15 C) in an HiP247 package Features Very tight variation of on-resistance vs. temperature Very high operating junction temperature
More information2-Phase Stepper Motor Unipolar Driver ICs
-Phase/- Phase Excitation -Phase Stepper Motor Unipolar Driver ICs Absolute Maximum Ratings Parameter Symbol Ratings SLA77MU SLA74M SLA76M Units Motor supply voltage CC 46 FET Drain-Source voltage DSS
More informationLDL212. High PSRR, low drop linear regulator IC. Datasheet. Features. Applications. Description
Datasheet High PSRR, low drop linear regulator IC Features Input voltage from 2.5 V to 18 V 2 V AMR Any fixed output voltages, from 1.2 V to 12 V in 1 mv steps (from 1.2 V to 6.6 V in 5 mv steps) available
More information74AUP2G34. Pin Assignments. Description ADVANCED INFORMATION. Features. Applications. (Top View) SOT363 X2-DFN X2-DFN X2-DFN1010-6
DUAL BUFFERS Description The Advanced Ultra Low Power (AUP) CMOS logic family is designed for low power and extended battery life in portable applications. The is composed of two buffers with standard
More informationOBSOLETE - PART DISCONTINUED
General Description The series are three terminal positive regulators designed for a wide variety of applications including local, on-card regulation. The are complete with internal current limiting, thermal
More informationIRGB30B60K IRGS30B60K IRGSL30B60K
INSULATED GATE BIPOLAR TRANSISTOR Features Low VCE on) Non Punch Through IGBT Technology. µs Short Circuit Capability. Square RBSOA. Positive VCE on) Temperature Coefficient. Maximum Junction Temperature
More information5A Low Dropout Linear Regulator
Solved by SP084 TM 5A Low Dropout Linear Regulator TO-- features INPUT Low Dropout oltage:. Typically at 5A Current Limiting and Thermal Protection Output Current: 5A Current Limit:.5A Operating Junction
More informationPrecision Hall-Effect Switch for Consumer and Industrial Applications
FEATURES AND BENEFITS Unipolar switchpoints Superior ruggedness and fault tolerance Reverse-polarity and transient protection Operation from 40 C to 175 C junction temperature Output short-circuit and
More information=25 C Avalanche Energy, single pulse 65 I C. C Soldering Temperature, for 10 seconds 300, (0.063 in. (1.6mm) from case)
PD- 94117 IRGP2B12U-E INSULATED GATE BIPOLAR TRANSISTOR Features UltraFast IGBT UltraFast Non Punch Through (NPT) Technology 1 µs Short Circuit capability Square RBSOA Positive V CE (on) Temperature Coefficient
More information