Review of 1 st Order Circuit Analysis
|
|
- Gabriel Potter
- 5 years ago
- Views:
Transcription
1 ECEN 60 Circuits/Electronics Spring P. Mathys Review of st Order Circuit Analysis First Order Differential Equation Consider the following circuit with input voltage v S (t) and output voltage v O (t). i R (t) R i C (t) v S (t) C v O (t) Recall that for capacitors i C (t) = C v () C (t), where v() C (t) denotes the first derivative (with respect to t) of v C (t). Using KCL i R (t) = i C (t) = Thus, the differential equation for this circuit is v S (t) v O (t) R = C v () O (t). v () O (t) v O(t) = v S (t), with initial condition v O (0) = V 0. Another way to write this is v () O (t) = v S(t) v O(t). This can be visualized using a block diagram with an integrator as shown below. v S (t) v () O (t) V 0 v O(t)
2 Natural Response To obtain the natural response (or homogeneous solution) of the st order differential equation v () O (t) v O(t) = v S (t), set v S (t) = 0 and assume a solution of the form v N (t) = K e st, t 0, = v () N (t) = Ks est, t 0, for some constants K and s. Substitute in the differential equation to obtain The nontrivial solution is Ks e st K e st = K (s ) e st = 0. s = 0 = s = = v N (t) = K e t/, t 0. Because the voltage across a capacitor is a state variable, the initial condition V 0 is the voltage across the capacitor at time t = 0, i.e., V 0 = v O (0) = v N (0) = K = v N (t) = V 0 e t/, t 0. 3 Forced Response: Step Input Let v S (t) = u(t) and assume a forced response (or particular solution) of the form v F (t) = V F, t 0, = v () F (t) = 0, t 0. Substitute in the differential equation to obtain V F = = v F (t) =, t 0. Next use superposition to combine the natural and forced solutions as v O (t) = v N (t) v F (t) = K e t/, t 0. Then use the initial condition V 0 = v O (0) to solve for K This yields the complete solution as V 0 = v O (0) = K = K = V 0. v O (t) = (V 0 ) e t/ }{{} V }{{} A natural forced = V 0 e }{{ t/ } ZIR ( e t/, t 0. }{{} ZSR The natural solution is also called transient response and the forced solution is also called steady-state response. ZIR stands for zero-input response and ZSR stands for zero-state response. The following graph shows v O (t) when V 0 /3.
3 V t 4 Forced Response: Sinusoidal Input Let v S (t) = cos ωt, t 0 and assume a solution of the form v F (t) = V F cos(ωt φ) = a cos ωt b sin ωt, where the Fourier coefficients a, b are given by (from cos(α β) = cos α cos β sin α sin β) a = V F cos φ, b = V F sin φ, and thus V F = a b, φ = tan b a. The first derivative of v F (t) (in Fourier coefficient format) is v () F (t) = aω sin ωt bω cos ωt, t 0. After substituting in the differential equation one obtains (aω sin ωt bω cos ωt) a cos ωt b sin ωt = cos ωt, t 0. Since cos ωt and sin ωt are orthogonal functions, this yields the following two equations (one for the coefficents of all the cos ωt terms and one for all the coefficients of the sin ωt terms) a b ω =, and a ω b = 0. In matrix-vector form this is [ ] [ ] ω a = ω b [ ] VA 0. Using Kramer s rule to solve for a and b yields ω 0 a = ω ω = (ω), 3
4 and b = ω 0 ω ω = ω (ω). Using superposition, the solution for v O (t) is the sum of v N (t) and v F (t), i.e., v O (t) = K e t/ To solve for K the initial condition v O (0) = V 0 is used (cos ωt ω sin ωt), t 0. (ω) V 0 = K = K = V (ω) 0 (ω). Thus, the complete solution is ( V ) A v O (t) = V 0 e t/ (cos ωt ω sin ωt) (ω) }{{ (ω) }}{{} transient response steady-state response. 5 Frequency Response More physical insight can be gained by converting the steady-state response from the Fourier coefficient format back to the form V F cos(ωt φ). This results in V F = a b = (ω) and φ = tan b a = tan ω, and thus ( V ) A v O (t) = V 0 e t/ (ω) }{{ } transient response (ω) cos(ωt tan ω) } {{ } steady-state response The combination of V F and φ is called the frequency response of the circuit. Individually, V F is called the magnitude of the frequency response and φ is called the phase of the frequency response. If a circuit has a frequency response magnitude that is larger for lower frequencies than higher frequencies, it is called a lowpass filter (LPF). Conversely, if a circuit has a frequency response magnitude that is smaller for lower frequencies than higher frequencies, it is called a highpass filter (HPF). Of special importance is the (cutoff) frequency ω c at which the output power of the circuit is reduced to one half of the input power. For V F as given above, this occurs for ω c = / as can be easily seen from V F ω=/ = (/) = =
5 Note that at ω = ω c φ ω=/ = tan (/) = tan = Phasors Using Euler s relationship e jθ = cos θ j sin θ, a sinusoid of the form v(t) = cos(ωt φ) can be expressed as The quantity v(t) = cos(ωt φ) = Re{ e j(ωtφ) } = Re{ e }{{ jφ e } jωt }. =V V = e jφ is called the (complex-valued) phasor representation of v(t). This can be expressed symbolically as v(t) V. Linearity (and thus the superposition principle) holds for phasors, i.e., K v (t) K v (t) K V K V, for arbitrary real constants K and K. Note that v (t) and v (t) must both be sinusoids of the same frequency for this to hold. The phasor representation of the derivative of v(t) is obtained from and thus v () (t) = d dt Re{V ejωt } = Re { d dt V ejωt} = Re{jωV e jωt }, v () (t) jωv. The i(t)-v(t) characteristic of a resistor can be expressed as For capacitors one obtains v R (t) = R i R (t) V R = R I R = Z = R. i C (t) = C v () C (t) I C = V C = Z =. For inductors the relationships are v L (t) = L i () L (t) V L = jωl I L = Z = jωl. 5
6 7 Phasor Analysis The figure below shows the LPF circuit labeled for phasor analysis. R V O Using voltage division one obtains immediately V O = R = jω. Multiplying through by jω yields the relationship jω V O V O = v () O (t) v O(t) = v S (t), i.e., the differential equation can be obtained directly from the phasor analysis (and vice versa). Dividing the output phasor V O = V O e jφ O by the input phasor = e jφ S, one can define the transfer function H of the circuit as H = V O = V O e jφo V s e jφ S = V O e j(φ Oφ S ). Note that H is a complex quantity in general that can be written as H = H e j H. The quantity H = V O / is the magnitude of the frequency response and H = φ O φ S is the phase of the frequency response of the circuit. For the LPF circuit H = jω = jω (ω) = (ω) ej tan ω, where H = ( (ω) ) is the magnitude and H = tan ω is the phase of the frequency response of the circuit. This is the same result as found earlier from the forced solution of the differential equation for a sinusoidal input signal. 6
7 8 Analysis of Highpass Filter If the roles of the capacitor and the resistor are interchanged, then the circuit shown below is obtained. C i C (t) v C (t) i R (t) v S (t) R v O (t) Because of the capacitor in series with the input signal v S (t), this circuit does not pass dc, but passes high frequencies and is therefore a highpass filter or differentiator. Starting from the phasor analysis this time, the schematic is relabeled as follows: V C R V O Using voltage division yields immediately V O = R R = which translates into the differential equation jω jω, jω V O V O = jω v () O (t) v O(t) = v () S (t). The frequency response of the circuit is found as H = V O = jω jω = jω ( jω) (ω) = ω (j ω). (ω) The magnitude H and the phase H of the frequency response are therefore H = ω, H = (ω) tan ω. The half-power (or cutoff) frequency is ω c = / and H ωc = / and H ωc = tan = 45. 7
8 To derive the step response of the system with a specified initial condition, the form of the differential equation obtained above is not suitable because v O (t) is not a state variable of the system. In this case it is better to first derive a differential equation for the state variable v C (t) = v S (t) v O (t), and then to obtain v O (t) as a function of v C (t). Noting that v O (t) = v S (t) v C (t) and i C (t) = i R (t) one can write v O (t) = v S (t) v C (t) = R i C (t) = v () C (t) = v() C (t) v C(t) = v S (t), with initial condition v C (0) = V 0. Since i C (t) = i R (t), the output voltage is related to v C (t) by v O (t) = R i C (t) = v () C (t). This is shown in block diagram form in the following figure: v O (t) v S (t) v () C (t) V 0 v C (t) The natural solution of the differential equation for v C (t) is v N = K e t/, t 0, and the forced solution in response to a step input v S (t) = u(t) is v F (t) =, t 0. Combining v N (t) and v F (t) and using the initial condition v C (0) = V 0 to solve for K yields v C (t) = (V 0 ) e t/, t 0. Thus, v O (t) = v () C (t) in response to a step input of amplitude is v O (t) = ( V 0 ) e t/ = e }{{ t/ V } 0 e t/, t 0. }{{} ZSR ZIR c , P. Mathys. Last revised: -3-07, PM. 8
Sinusoids and Phasors
CHAPTER 9 Sinusoids and Phasors We now begins the analysis of circuits in which the voltage or current sources are time-varying. In this chapter, we are particularly interested in sinusoidally time-varying
More informationPhasors: Impedance and Circuit Anlysis. Phasors
Phasors: Impedance and Circuit Anlysis Lecture 6, 0/07/05 OUTLINE Phasor ReCap Capacitor/Inductor Example Arithmetic with Complex Numbers Complex Impedance Circuit Analysis with Complex Impedance Phasor
More informationCircuit Analysis-III. Circuit Analysis-II Lecture # 3 Friday 06 th April, 18
Circuit Analysis-III Sinusoids Example #1 ü Find the amplitude, phase, period and frequency of the sinusoid: v (t ) =12cos(50t +10 ) Signal Conversion ü From sine to cosine and vice versa. ü sin (A ± B)
More informationSCHOOL OF MATHEMATICS MATHEMATICS FOR PART I ENGINEERING. Self-paced Course
SCHOOL OF MATHEMATICS MATHEMATICS FOR PART I ENGINEERING Self-paced Course MODULE 26 APPLICATIONS TO ELECTRICAL CIRCUITS Module Topics 1. Complex numbers and alternating currents 2. Complex impedance 3.
More information09/29/2009 Reading: Hambley Chapter 5 and Appendix A
EE40 Lec 10 Complex Numbers and Phasors Prof. Nathan Cheung 09/29/2009 Reading: Hambley Chapter 5 and Appendix A Slide 1 OUTLINE Phasors as notation for Sinusoids Arithmetic with Complex Numbers Complex
More informationPhasor Diagram. Figure 1: Phasor Diagram. A φ. Leading Direction. θ B. Lagging Direction. Imag. Axis Complex Plane. Real Axis
1 16.202: PHASORS Consider sinusoidal source i(t) = Acos(ωt + φ) Using Eulers Notation: Acos(ωt + φ) = Re[Ae j(ωt+φ) ] Phasor Representation of i(t): = Ae jφ = A φ f v(t) = Bsin(ωt + ψ) First convert the
More informationChapter 10: Sinusoidal Steady-State Analysis
Chapter 10: Sinusoidal Steady-State Analysis 1 Objectives : sinusoidal functions Impedance use phasors to determine the forced response of a circuit subjected to sinusoidal excitation Apply techniques
More informationImpedance and Loudspeaker Parameter Measurement
ECEN 2260 Circuits/Electronics 2 Spring 2007 2-26-07 P. Mathys Impedance and Loudspeaker Parameter Measurement 1 Impedance Measurement Many elements from which electrical circuits are built are two-terminal
More informationEE100Su08 Lecture #11 (July 21 st 2008)
EE100Su08 Lecture #11 (July 21 st 2008) Bureaucratic Stuff Lecture videos should be up by tonight HW #2: Pick up from office hours today, will leave them in lab. REGRADE DEADLINE: Monday, July 28 th 2008,
More informationElectric Circuit Theory
Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 11 Sinusoidal Steady-State Analysis Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Contents and Objectives 3 Chapter Contents 11.1
More informationFrequency Response. Re ve jφ e jωt ( ) where v is the amplitude and φ is the phase of the sinusoidal signal v(t). ve jφ
27 Frequency Response Before starting, review phasor analysis, Bode plots... Key concept: small-signal models for amplifiers are linear and therefore, cosines and sines are solutions of the linear differential
More informationI. Impedance of an R-L circuit.
I. Impedance of an R-L circuit. [For inductor in an AC Circuit, see Chapter 31, pg. 1024] Consider the R-L circuit shown in Figure: 1. A current i(t) = I cos(ωt) is driven across the circuit using an AC
More informationd n 1 f dt n 1 + K+ a 0f = C cos(ωt + φ)
Tutorial TUTOR: THE PHASOR TRANSFORM All voltages currents in linear circuits with sinusoidal sources are described by constant-coefficient linear differential equations of the form (1) a n d n f dt n
More informationChapter 10: Sinusoids and Phasors
Chapter 10: Sinusoids and Phasors 1. Motivation 2. Sinusoid Features 3. Phasors 4. Phasor Relationships for Circuit Elements 5. Impedance and Admittance 6. Kirchhoff s Laws in the Frequency Domain 7. Impedance
More informationSchool of Electrical and Computer Engineering ECE2040 Dr. George F. Riley Summer 2007, GT Lorraine Analysis of LRC with Sinusoidal Sources
School of Electrical and Computer Engineering ECE2040 Dr. George F. Riley Summer 2007, GT Lorraine Analysis of LRC with Sinusoidal Sources In chapter 8 in the textbook, we determined that if the forcing
More informationSinusoidal Steady-State Analysis
Sinusoidal Steady-State Analysis Mauro Forti October 27, 2018 Constitutive Relations in the Frequency Domain Consider a network with independent voltage and current sources at the same angular frequency
More informationSinusoidal Steady-State Analysis
Chapter 4 Sinusoidal Steady-State Analysis In this unit, we consider circuits in which the sources are sinusoidal in nature. The review section of this unit covers most of section 9.1 9.9 of the text.
More informationElectric Circuits II Sinusoidal Steady State Analysis. Dr. Firas Obeidat
Electric Circuits II Sinusoidal Steady State Analysis Dr. Firas Obeidat 1 Table of Contents 1 2 3 4 5 Nodal Analysis Mesh Analysis Superposition Theorem Source Transformation Thevenin and Norton Equivalent
More information15 n=0. zz = re jθ re jθ = r 2. (b) For division and multiplication, it is handy to use the polar representation: z = rejθ. = z 1z 2.
Professor Fearing EECS0/Problem Set v.0 Fall 06 Due at 4 pm, Fri. Sep. in HW box under stairs (st floor Cory) Reading: EE6AB notes. This problem set should be review of material from EE6AB. (Please note,
More informationChapter 9 Objectives
Chapter 9 Engr8 Circuit Analysis Dr Curtis Nelson Chapter 9 Objectives Understand the concept of a phasor; Be able to transform a circuit with a sinusoidal source into the frequency domain using phasor
More informationEE292: Fundamentals of ECE
EE292: Fundamentals of ECE Fall 2012 TTh 10:00-11:15 SEB 1242 Lecture 18 121025 http://www.ee.unlv.edu/~b1morris/ee292/ 2 Outline Review RMS Values Complex Numbers Phasors Complex Impedance Circuit Analysis
More informationReview of Linear Time-Invariant Network Analysis
D1 APPENDIX D Review of Linear Time-Invariant Network Analysis Consider a network with input x(t) and output y(t) as shown in Figure D-1. If an input x 1 (t) produces an output y 1 (t), and an input x
More informationR-L-C Circuits and Resonant Circuits
P517/617 Lec4, P1 R-L-C Circuits and Resonant Circuits Consider the following RLC series circuit What's R? Simplest way to solve for is to use voltage divider equation in complex notation. X L X C in 0
More informationEE 40: Introduction to Microelectronic Circuits Spring 2008: Midterm 2
EE 4: Introduction to Microelectronic Circuits Spring 8: Midterm Venkat Anantharam 3/9/8 Total Time Allotted : min Total Points:. This is a closed book exam. However, you are allowed to bring two pages
More informationSinusoidal steady-state analysis
Sinusoidal steady-state analysis From our previous efforts with AC circuits, some patterns in the analysis started to appear. 1. In each case, the steady-state voltages or currents created in response
More informationChapter 33. Alternating Current Circuits
Chapter 33 Alternating Current Circuits 1 Capacitor Resistor + Q = C V = I R R I + + Inductance d I Vab = L dt AC power source The AC power source provides an alternative voltage, Notation - Lower case
More informationComplex Numbers Review
Complex Numbers view ference: Mary L. Boas, Mathematical Methods in the Physical Sciences Chapter 2 & 4 George Arfken, Mathematical Methods for Physicists Chapter 6 The real numbers (denoted R) are incomplete
More informationHarman Outline 1A CENG 5131
Harman Outline 1A CENG 5131 Numbers Real and Imaginary PDF In Chapter 2, concentrate on 2.2 (MATLAB Numbers), 2.3 (Complex Numbers). A. On R, the distance of any real number from the origin is the magnitude,
More informationAC analysis - many examples
AC analysis - many examples The basic method for AC analysis:. epresent the AC sources as complex numbers: ( ). Convert resistors, capacitors, and inductors into their respective impedances: resistor Z
More informationLecture 4: R-L-C Circuits and Resonant Circuits
Lecture 4: R-L-C Circuits and Resonant Circuits RLC series circuit: What's V R? Simplest way to solve for V is to use voltage divider equation in complex notation: V X L X C V R = in R R + X C + X L L
More information1 Phasors and Alternating Currents
Physics 4 Chapter : Alternating Current 0/5 Phasors and Alternating Currents alternating current: current that varies sinusoidally with time ac source: any device that supplies a sinusoidally varying potential
More informationP A R T 2 AC CIRCUITS. Chapter 9 Sinusoids and Phasors. Chapter 10 Sinusoidal Steady-State Analysis. Chapter 11 AC Power Analysis
P A R T 2 AC CIRCUITS Chapter 9 Sinusoids and Phasors Chapter 10 Sinusoidal Steady-State Analysis Chapter 11 AC Power Analysis Chapter 12 Three-Phase Circuits Chapter 13 Magnetically Coupled Circuits Chapter
More informationRefinements to Incremental Transistor Model
Refinements to Incremental Transistor Model This section presents modifications to the incremental models that account for non-ideal transistor behavior Incremental output port resistance Incremental changes
More informationEE292: Fundamentals of ECE
EE292: Fundamentals of ECE Fall 2012 TTh 10:00-11:15 SEB 1242 Lecture 20 121101 http://www.ee.unlv.edu/~b1morris/ee292/ 2 Outline Chapters 1-3 Circuit Analysis Techniques Chapter 10 Diodes Ideal Model
More informationREACTANCE. By: Enzo Paterno Date: 03/2013
REACTANCE REACTANCE By: Enzo Paterno Date: 03/2013 5/2007 Enzo Paterno 1 RESISTANCE - R i R (t R A resistor for all practical purposes is unaffected by the frequency of the applied sinusoidal voltage or
More informationChapter 10: Sinusoidal Steady-State Analysis
Chapter 10: Sinusoidal Steady-State Analysis 10.1 10.2 10.3 10.4 10.5 10.6 10.9 Basic Approach Nodal Analysis Mesh Analysis Superposition Theorem Source Transformation Thevenin & Norton Equivalent Circuits
More informationHandout 11: AC circuit. AC generator
Handout : AC circuit AC generator Figure compares the voltage across the directcurrent (DC) generator and that across the alternatingcurrent (AC) generator For DC generator, the voltage is constant For
More informationFall 2011 ME 2305 Network Analysis. Sinusoidal Steady State Analysis of RLC Circuits
Fall 2011 ME 2305 Network Analysis Chapter 4 Sinusoidal Steady State Analysis of RLC Circuits Engr. Humera Rafique Assistant Professor humera.rafique@szabist.edu.pk Faculty of Engineering (Mechatronics)
More information1.3 Sinusoidal Steady State
1.3 Sinusoidal Steady State Electromagnetics applications can be divided into two broad classes: Time-domain: Excitation is not sinusoidal (pulsed, broadband, etc.) Ultrawideband communications Pulsed
More informationSINUSOIDAL STEADY STATE CIRCUIT ANALYSIS
SINUSOIDAL STEADY STATE CIRCUIT ANALYSIS 1. Introduction A sinusoidal current has the following form: where I m is the amplitude value; ω=2 πf is the angular frequency; φ is the phase shift. i (t )=I m.sin
More information15-884/484 Electric Power Systems 1: DC and AC Circuits
15-884/484 Electric Power Systems 1: DC and AC Circuits J. Zico Kolter October 8, 2013 1 Hydro Estimated U.S. Energy Use in 2010: ~98.0 Quads Lawrence Livermore National Laboratory Solar 0.11 0.01 8.44
More informationSinusoidal Steady State Analysis (AC Analysis) Part I
Sinusoidal Steady State Analysis (AC Analysis) Part I Amin Electronics and Electrical Communications Engineering Department (EECE) Cairo University elc.n102.eng@gmail.com http://scholar.cu.edu.eg/refky/
More information11. AC Circuit Power Analysis
. AC Circuit Power Analysis Often an integral part of circuit analysis is the determination of either power delivered or power absorbed (or both). In this chapter First, we begin by considering instantaneous
More informationBME/ISE 3511 Bioelectronics - Test Six Course Notes Fall 2016
BME/ISE 35 Bioelectronics - Test Six ourse Notes Fall 06 Alternating urrent apacitive & Inductive Reactance and omplex Impedance R & R ircuit Analyses (D Transients, Time onstants, Steady State) Electrical
More informationThree Phase Circuits
Amin Electronics and Electrical Communications Engineering Department (EECE) Cairo University elc.n102.eng@gmail.com http://scholar.cu.edu.eg/refky/ OUTLINE Previously on ELCN102 Three Phase Circuits Balanced
More informationModule 25: Outline Resonance & Resonance Driven & LRC Circuits Circuits 2
Module 25: Driven RLC Circuits 1 Module 25: Outline Resonance & Driven LRC Circuits 2 Driven Oscillations: Resonance 3 Mass on a Spring: Simple Harmonic Motion A Second Look 4 Mass on a Spring (1) (2)
More informationCIRCUIT ANALYSIS II. (AC Circuits)
Will Moore MT & MT CIRCUIT ANALYSIS II (AC Circuits) Syllabus Complex impedance, power factor, frequency response of AC networks including Bode diagrams, second-order and resonant circuits, damping and
More informationTo find the step response of an RC circuit
To find the step response of an RC circuit v( t) v( ) [ v( t) v( )] e tt The time constant = RC The final capacitor voltage v() The initial capacitor voltage v(t ) To find the step response of an RL circuit
More informationLecture 9 Time Domain vs. Frequency Domain
. Topics covered Lecture 9 Time Domain vs. Frequency Domain (a) AC power in the time domain (b) AC power in the frequency domain (c) Reactive power (d) Maximum power transfer in AC circuits (e) Frequency
More informationChapter 5 Frequency Domain Analysis of Systems
Chapter 5 Frequency Domain Analysis of Systems CT, LTI Systems Consider the following CT LTI system: xt () ht () yt () Assumption: the impulse response h(t) is absolutely integrable, i.e., ht ( ) dt< (this
More informationEE40 Lecture 11 Josh Hug 7/19/2010
EE40 Lecture Josh 7/9/200 Logistical Things Lab 4 tomorrow Lab 5 (active filter lab) on Wednesday Prototype for future lab for EE40 Prelab is very short, sorry. Please give us our feedback Google docs
More informationEE 3120 Electric Energy Systems Study Guide for Prerequisite Test Wednesday, Jan 18, pm, Room TBA
EE 3120 Electric Energy Systems Study Guide for Prerequisite Test Wednesday, Jan 18, 2006 6-7 pm, Room TBA First retrieve your EE2110 final and other course papers and notes! The test will be closed book
More informationLecture 7: Laplace Transform and Its Applications Dr.-Ing. Sudchai Boonto
Dr-Ing Sudchai Boonto Department of Control System and Instrumentation Engineering King Mongkut s Unniversity of Technology Thonburi Thailand Outline Motivation The Laplace Transform The Laplace Transform
More informationSinusoidal Steady State Analysis (AC Analysis) Part II
Sinusoidal Steady State Analysis (AC Analysis) Part II Amin Electronics and Electrical Communications Engineering Department (EECE) Cairo University elc.n102.eng@gmail.com http://scholar.cu.edu.eg/refky/
More informationElectric Circuit Theory
Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 8 Natural and Step Responses of RLC Circuits Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 8.1 Introduction to the Natural Response
More informationExplanations and Discussion of Some Laplace Methods: Transfer Functions and Frequency Response. Y(s) = b 1
Engs 22 p. 1 Explanations Discussion of Some Laplace Methods: Transfer Functions Frequency Response I. Anatomy of Differential Equations in the S-Domain Parts of the s-domain solution. We will consider
More informationC R. Consider from point of view of energy! Consider the RC and LC series circuits shown:
ircuits onsider the R and series circuits shown: ++++ ---- R ++++ ---- Suppose that the circuits are formed at t with the capacitor charged to value. There is a qualitative difference in the time development
More informationECE 45 Average Power Review
UC San Diego J. Connelly Complex Power ECE 45 Average Power Review When dealing with time-dependent voltage and currents, we have to consider a more general definition of power. We can calculate the instantaneous
More informationSinusoidal Steady State Analysis
Sinusoidal Steady State Analysis 9 Assessment Problems AP 9. [a] V = 70/ 40 V [b] 0 sin(000t +20 ) = 0 cos(000t 70 ).. I = 0/ 70 A [c] I =5/36.87 + 0/ 53.3 =4+j3+6 j8 =0 j5 =.8/ 26.57 A [d] sin(20,000πt
More informationAnnouncements: Today: more AC circuits
Announcements: Today: more AC circuits I 0 I rms Current through a light bulb I 0 I rms I t = I 0 cos ωt I 0 Current through a LED I t = I 0 cos ωt Θ(cos ωt ) Theta function (is zero for a negative argument)
More informationOrdinary differential equations
Class 7 Today s topics The nonhomogeneous equation Resonance u + pu + qu = g(t). The nonhomogeneous second order linear equation This is the nonhomogeneous second order linear equation u + pu + qu = g(t).
More informationLectures 16 & 17 Sinusoidal Signals, Complex Numbers, Phasors, Impedance & AC Circuits. Nov. 7 & 9, 2011
Lectures 16 & 17 Sinusoidal Signals, Complex Numbers, Phasors, Impedance & AC Circuits Nov. 7 & 9, 2011 Material from Textbook by Alexander & Sadiku and Electrical Engineering: Principles & Applications,
More informationEECE 2150 Circuits and Signals Final Exam Fall 2016 Dec 16
EECE 2150 Circuits and Signals Final Exam Fall 2016 Dec 16 Instructions: Write your name and section number on all pages Closed book, closed notes; Computers and cell phones are not allowed You can use
More informationPhysics 294H. lectures will be posted frequently, mostly! every day if I can remember to do so
Physics 294H l Professor: Joey Huston l email:huston@msu.edu l office: BPS3230 l Homework will be with Mastering Physics (and an average of 1 hand-written problem per week) Help-room hours: 12:40-2:40
More informationPhasor mathematics. Resources and methods for learning about these subjects (list a few here, in preparation for your research):
Phasor mathematics This worksheet and all related files are licensed under the Creative Commons Attribution License, version 1.0. To view a copy of this license, visit http://creativecommons.org/licenses/by/1.0/,
More informationChapter 10 Sinusoidal Steady State Analysis Chapter Objectives:
Chapter 10 Sinusoidal Steady State Analysis Chapter Objectives: Apply previously learn circuit techniques to sinusoidal steady-state analysis. Learn how to apply nodal and mesh analysis in the frequency
More informationECE Circuit Theory. Final Examination. December 5, 2008
ECE 212 H1F Pg 1 of 12 ECE 212 - Circuit Theory Final Examination December 5, 2008 1. Policy: closed book, calculators allowed. Show all work. 2. Work in the provided space. 3. The exam has 3 problems
More informationCourse Updates. Reminders: 1) Assignment #10 due Today. 2) Quiz # 5 Friday (Chap 29, 30) 3) Start AC Circuits
ourse Updates http://www.phys.hawaii.edu/~varner/phys272-spr10/physics272.html eminders: 1) Assignment #10 due Today 2) Quiz # 5 Friday (hap 29, 30) 3) Start A ircuits Alternating urrents (hap 31) In this
More informationChapter 8: Frequency Domain Analysis
Chapter 8: Frequency Domain Analysis Samantha Ramirez Preview Questions 1. What is the steady-state response of a linear system excited by a cyclic or oscillatory input? 2. How does one characterize the
More informationAlternating Current (AC) Circuits
Alternating Current (AC) Circuits We have been talking about DC circuits Constant currents and voltages Resistors Linear equations Now we introduce AC circuits Time-varying currents and voltages Resistors,
More informationBioelectrical Circuits: Lecture 9
City University of New York (CUNY) CUNY Academic Works Open Educational Resources City College of New York 2019 Bioelectrical Circuits: Lecture 9 Jacek P. Dmochowski CUNY City College Luis Cardoso CUNY
More information8. Introduction and Chapter Objectives
Real Analog - Circuits Chapter 8: Second Order Circuits 8. Introduction and Chapter Objectives Second order systems are, by definition, systems whose input-output relationship is a second order differential
More informationCircuits and Systems I
Circuits and Systems I LECTURE #2 Phasor Addition lions@epfl Prof. Dr. Volkan Cevher LIONS/Laboratory for Information and Inference Systems License Info for SPFirst Slides This work released under a Creative
More informationK.K. Gan L3: R-L-C AC Circuits. amplitude. Volts. period. -Vo
Lecture 3: R-L-C AC Circuits AC (Alternative Current): Most of the time, we are interested in the voltage at a point in the circuit will concentrate on voltages here rather than currents. We encounter
More informationFourier series. XE31EO2 - Pavel Máša. Electrical Circuits 2 Lecture1. XE31EO2 - Pavel Máša - Fourier Series
Fourier series Electrical Circuits Lecture - Fourier Series Filtr RLC defibrillator MOTIVATION WHAT WE CAN'T EXPLAIN YET Source voltage rectangular waveform Resistor voltage sinusoidal waveform - Fourier
More informationChapter 10 AC Analysis Using Phasors
Chapter 10 AC Analysis Using Phasors 10.1 Introduction We would like to use our linear circuit theorems (Nodal analysis, Mesh analysis, Thevenin and Norton equivalent circuits, Superposition, etc.) to
More informationTransmission lines. Shouri Chatterjee. October 22, 2014
Transmission lines Shouri Chatterjee October 22, 2014 The transmission line is a very commonly used distributed circuit: a pair of wires. Unfortunately, a pair of wires used to apply a time-varying voltage,
More informationProf. Shayla Sawyer CP08 solution
What does the time constant represent in an exponential function? How do you define a sinusoid? What is impedance? How is a capacitor affected by an input signal that changes over time? How is an inductor
More informationLINEAR CIRCUIT ANALYSIS (EED) U.E.T. TAXILA 09
LINEAR CIRCUIT ANALYSIS (EED) U.E.T. TAXILA 09 ENGR. M. MANSOOR ASHRAF INTRODUCTION Thus far our analysis has been restricted for the most part to dc circuits: those circuits excited by constant or time-invariant
More information16.362: Signals and Systems: 1.0
16.362: Signals and Systems: 1.0 Prof. K. Chandra ECE, UMASS Lowell September 1, 2016 1 Background The pre-requisites for this course are Calculus II and Differential Equations. A basic understanding of
More informationLecture 11 - AC Power
- AC Power 11/17/2015 Reading: Chapter 11 1 Outline Instantaneous power Complex power Average (real) power Reactive power Apparent power Maximum power transfer Power factor correction 2 Power in AC Circuits
More information3 What You Should Know About Complex Numbers
3 What You Should Know About Complex Numbers Life is complex it has a real part, and an imaginary part Andrew Koenig. Complex numbers are an extension of the more familiar world of real numbers that make
More informationSolutions to Problems in Chapter 4
Solutions to Problems in Chapter 4 Problems with Solutions Problem 4. Fourier Series of the Output Voltage of an Ideal Full-Wave Diode Bridge Rectifier he nonlinear circuit in Figure 4. is a full-wave
More informationSinusoidal Steady-State Analysis
Sinusoidal Steady-State Analysis Almost all electrical systems, whether signal or power, operate with alternating currents and voltages. We have seen that when any circuit is disturbed (switched on or
More informationSchedule. ECEN 301 Discussion #20 Exam 2 Review 1. Lab Due date. Title Chapters HW Due date. Date Day Class No. 10 Nov Mon 20 Exam Review.
Schedule Date Day lass No. 0 Nov Mon 0 Exam Review Nov Tue Title hapters HW Due date Nov Wed Boolean Algebra 3. 3.3 ab Due date AB 7 Exam EXAM 3 Nov Thu 4 Nov Fri Recitation 5 Nov Sat 6 Nov Sun 7 Nov Mon
More informationFirst and Second Order Circuits. Claudio Talarico, Gonzaga University Spring 2015
First and Second Order Circuits Claudio Talarico, Gonzaga University Spring 2015 Capacitors and Inductors intuition: bucket of charge q = Cv i = C dv dt Resist change of voltage DC open circuit Store voltage
More informationLab 3: Poles, Zeros, and Time/Frequency Domain Response
ECEN 33 Linear Systems Spring 2 2-- P. Mathys Lab 3: Poles, Zeros, and Time/Frequency Domain Response of CT Systems Introduction Systems that are used for signal processing are very often characterized
More informationChapter 5 Frequency Domain Analysis of Systems
Chapter 5 Frequency Domain Analysis of Systems CT, LTI Systems Consider the following CT LTI system: xt () ht () yt () Assumption: the impulse response h(t) is absolutely integrable, i.e., ht ( ) dt< (this
More informationBFF1303: ELECTRICAL / ELECTRONICS ENGINEERING. Alternating Current Circuits : Basic Law
BFF1303: ELECTRICAL / ELECTRONICS ENGINEERING Alternating Current Circuits : Basic Law Ismail Mohd Khairuddin, Zulkifil Md Yusof Faculty of Manufacturing Engineering Universiti Malaysia Pahang Alternating
More information1. (10 points) Find the general solution to the following second-order differential equation:
Math 307A, Winter 014 Midterm Solutions Page 1 of 8 1. (10 points) Find the general solution to the following second-order differential equation: 4y 1y + 9y = 9t. To find the general solution to this nonhomogeneous
More informationPHYSICS 110A : CLASSICAL MECHANICS HW 2 SOLUTIONS. Here is a sketch of the potential with A = 1, R = 1, and S = 1. From the plot we can see
PHYSICS 11A : CLASSICAL MECHANICS HW SOLUTIONS (1) Taylor 5. Here is a sketch of the potential with A = 1, R = 1, and S = 1. From the plot we can see 1.5 1 U(r).5.5 1 4 6 8 1 r Figure 1: Plot for problem
More informationDesigning Information Devices and Systems II Spring 2016 Anant Sahai and Michel Maharbiz Midterm 2
EECS 16B Designing Information Devices and Systems II Spring 2016 Anant Sahai and Michel Maharbiz Midterm 2 Exam location: 145 Dwinelle (SIDs ending in 1 and 5) PRINT your student ID: PRINT AND SIGN your
More informationEE221 Circuits II. Chapter 14 Frequency Response
EE22 Circuits II Chapter 4 Frequency Response Frequency Response Chapter 4 4. Introduction 4.2 Transfer Function 4.3 Bode Plots 4.4 Series Resonance 4.5 Parallel Resonance 4.6 Passive Filters 4.7 Active
More informationP441 Analytical Mechanics - I. RLC Circuits. c Alex R. Dzierba. In this note we discuss electrical oscillating circuits: undamped, damped and driven.
Lecture 10 Monday - September 19, 005 Written or last updated: September 19, 005 P441 Analytical Mechanics - I RLC Circuits c Alex R. Dzierba Introduction In this note we discuss electrical oscillating
More informationName (print): Lab (circle): W8 Th8 Th11 Th2 F8. θ (radians) θ (degrees) cos θ sin θ π/ /2 1/2 π/4 45 2/2 2/2 π/3 60 1/2 3/2 π/
Name (print): Lab (circle): W8 Th8 Th11 Th2 F8 Trigonometric Identities ( cos(θ) = cos(θ) sin(θ) = sin(θ) sin(θ) = cos θ π ) 2 Cosines and Sines of common angles Euler s Formula θ (radians) θ (degrees)
More informationLecture 15: Sinusoidal Steady State (SSS) Analysis or Phasors without a Phasor more or less
Spring 18 page 1 Lecture 15: Sinusoidal Steady State (SSS) Analysis or Phasors without a Phasor more or less 1. Definition. A signal f (t) is periodic with period T > 0 if f (t) = f (t + T ) ; the smallest
More informationBasic Electronics. Introductory Lecture Course for. Technology and Instrumentation in Particle Physics Chicago, Illinois June 9-14, 2011
Basic Electronics Introductory Lecture Course for Technology and Instrumentation in Particle Physics 2011 Chicago, Illinois June 9-14, 2011 Presented By Gary Drake Argonne National Laboratory Session 2
More informationEE221 Circuits II. Chapter 14 Frequency Response
EE22 Circuits II Chapter 4 Frequency Response Frequency Response Chapter 4 4. Introduction 4.2 Transfer Function 4.3 Bode Plots 4.4 Series Resonance 4.5 Parallel Resonance 4.6 Passive Filters 4.7 Active
More informationRefresher course on Electrical fundamentals (Basics of A.C. Circuits) by B.M.Vyas
Refresher course on Electrical fundamentals (Basics of A.C. Circuits) by B.M.Vyas A specifically designed programme for Da Afghanistan Breshna Sherkat (DABS) Afghanistan 1 Areas Covered Under this Module
More information2 Signal Frequency and Impedances First Order Filter Circuits Resonant and Second Order Filter Circuits... 13
Lecture Notes: 3454 Physics and Electronics Lecture ( nd Half), Year: 7 Physics Department, Faculty of Science, Chulalongkorn University //7 Contents Power in Ac Circuits Signal Frequency and Impedances
More information