PI3B V, Dual 4:1 Mux/DeMux NanoSwitch

Transcription

1 3.3V, Dual 4: Mux/DeMux NanoSwitch Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Fast Switching Speed: 5.2ns max. Ultra Low Quiescent Power (0.2μA typical) Ideally suited for notebook applications Pin compatible with 74 series 253 logic devices Packaging (Pb-free & Green available): 6-pin 50-mil wide plastic QSOP (Q) 6-pin 50-mil wide plastic SOIC (W) 6-pin 73-mil wide plastic TSSOP (L) Block Diagram Description Pericom Semiconductor s PI3B3253 is a 3.3V, Dual4: Multiplexer/ Demultiplexer with Hi-Z outputs that is pinout compatible with the PI74FCT253T, 74F253, and 74ALS/AS/LS 253. Inputs can be connected to outputs with low On-Resistance (5Ω) with no additional ground bounce noise or propagation delay. Pin Configuration IA0 IA IA2 IA3 IB0 IB IB2 IB3 EA EB S0 I Y EA S IA3 IA2 IA V CC EB S0 IB3 IB2 S E IA0 YA GND IB IB0 YB YA YB Truth Table () Enable Select E A E B S S 0 Y A Y B Function H X X X Hi-Z X Disable A X H X X X Hi-Z Disable B L L L L IA 0 I B 0 S-0 = 0 L L L H IA I B S-0 = L L H L IA 2 I B 2 S-0 = 2 L L H H IA 3 I B 3 S-0 = 3 Note:. H = High Voltage Level, L = Low Voltage Level Pin Description Pin Name IA N, I B N S 0- E A, E B Y A, Y B GND V CC Description Data Inputs Select Inputs Enable Data Outputs Ground Power PS847J 2/3/06

2 3.3V, Dual 4: Mux/DeMux NanoSwitch Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature C to +50 C Ambient Temperature with Power Applied C to +85 C Supply Voltage to Ground Potential V to +4.6V DC Input Voltage V to +4.6V DC Output Current... 20mA Power Dissipation W Note: Stresses greater than those listed under MAX I MUM RATINGS may cause per ma nent dam age to the device. This is a stress rating only and func tion al oper a tion of the device at these or any other con di tions above those indicated in the operational sec tions of this specification is not implied. Ex po sure to absolute maximum rating conditions for ex tend ed periods may affect re li abil i ty. DC Electrical Characteristics (Over the Operating Range, T A = 40 C to +85 C, V CC =3.3V ±0%) Parameters Description Test Conditions () Min. Typ. (2) Max. Units V IH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 V IL Input LOW Voltage Guaranteed Logic LOW Level I IH Input HIGH Current V CC = Max., V IN = V CC ± I IL Input LOW Current V CC = Max., V IN = GND ± I OZH High Impedance Output Current 0 I N, Y N V CC ± V IK Clamp Diode Voltage V CC = Min., I IN = 8mA.2 V R ON Switch On-Resistance (3) I ON = 48mA or 64mA V CC = Min., V IN = 0.0V, Capacitance (T A = 25 C, f = MHz) Parameters () Description Test Conditions Typ. Units C IN Input Capacitance C OFF I A /I B Capacitance, Switch Off V IN = 0V 8.0 C ON I A /I B Capacitance, Switch On V CC = Min., V IN = 2.4V, I ON = 5mA 0 7. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at V CC = 3.3V, T A = 25 C ambient and maximum loading. 3. Measured by the voltage drop between I and Y pin at indicated current through the switch. On-Resistance is de ter mined by the lower of the voltages on the two (I,Y) pins.. This parameter is determined by device characterization but is not production tested. 3.0 pf V μa Ω 2 PS847J 2/3/06

3 3.3V, Dual 4: Mux/DeMux NanoSwitch Power Supply Characteristics Parameters Description Test Conditions () Min. Typ. (2) Max. Units I CC Quiescent Power Supply Current V CC = Max. V IN = GND or V CC ΔI CC Supply Current per TTL HIGH V CC = Max. V IN = 3.0V (3) 750. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at V CC = 3.3V, +25 C ambient. 3. Per TTL driven input (control inputs only); I and Y pins do not contribute to I CC. μa Switching Characteristics over Operating Range Parameters Description Test Conditions Com. Min. Max. t IY Propagation Delay (,2) In to Yn t SY Bus Select Time, Sn to Yn C L = 50pF 4.0 t PZH Bus Enable Time, E to Yn R L = 500Ω 3.8 Units ns t PHZ t PLZ Bus Disable Time, En to Y 5.2. This parameter is guaranteed but not tested on Propagation Delays. 2. The bus switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is de ter mined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Applications Information Logic Inputs The logic control inputs can be driven up to +3.6V regardless of the supply voltage. For example, given a +3.3V supply, IN may be driven low to 0V and high to 3.6V. Driving IN Rail-to-Rail minimizes power consumption. Power-Supply Sequencing and Hot Plug Information Proper power-supply sequencing is recommended for all CMOS devices. Always apply V CC and GND before applying signals to input/output or control pins. Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. 3 PS847J 2/3/06

4 3.3V, Dual 4: Mux/DeMux NanoSwitch Packaging Mechanical: 6-Pin QSOP (Q) Guage Plane MIN Detail A x Detail A SEATING PLANE X.XX X.XX DENOTES DIMENSIONS IN MILLIMETERS Packaging Mechanical: 6-Pin SOIC (W) x SEATING PLANE X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS 4 PS847J 2/3/06

5 3.3V, Dual 4: Mux/DeMux NanoSwitch Packaging Mechanical: 6-Pin TSSOP (L) max..20 SEATING PLANE Ordering Information Ordering Code Package Code Package Desciption PI3B3253Q Q 6-pin QSOP PI3B3253QE Q Pb-free & Green, 6-pin QSOP PI3B3253W W 6-pin SOIC PI3B3253L L 6-pin TSSOP PI3B3253LE L Pb-free & Green, 6-pin TSSOP Thermal characteristics can be found on the company web site at E = Pb-free & Green Adding an X suffix = Tape/Reel Pericom Semiconductor Corporation PS847J 2/3/06