by Dr. Shibayan Sarkar Department of Mechanical Engineering

Size: px

Start display at page:

Download "by Dr. Shibayan Sarkar Department of Mechanical Engineering"

Ralph Morrison
5 years ago
Views:

1 Lecture on Pump by Dr. Shibayan Sarkar Department of Mechanical Engineering Indian School of Mines Dhanbad

2 WHAT IS PUMP? A hydrodynamic pump machine is a device which converts the mechanical energy held by a device into potential and kinetic energy in fluid. Pumps enable a liquid to: 1. Flow from a region or low pressure to one of high pressure.. Flow from a low level to a higher level. PUMP 3. Flow at a faster rate. Pump is the machine designed to move fluid and add energy to them. Rotodynamic Positive displacement Centrifugal There are two main categories of pump Rotary Reciprocating according to design and Axial flow principle of operation: Mixed flow Rotodynamic pumps. Gear Piston Positive displacement pumps. Turbine Lobe Diaphragm Based on direction of fluid flow relative to shaft Radial (centrifugal pumps) Axial (boat propellers) Mixed Sliding Vane Plunger Single- vs multi-stage(diffuser t type casing is used, pump impellers are connected in series) Constant vs variable speed ( to operate under different load efficiently) Screw Pneumatic

3 CHARACTERISTICS OF POSITIVE DISPLACEMENT PUMPS Rotary:- Rotating action occurs periodically. Gear comprises two gears in a housing with small radial end clearances. Used in lubrication system. Lobe- Handles solids also. Used in paper and pulp industry. Sliding Vane comprises number of vanes. Screw- three screw with housing is used with housing. Can create high pressure, uniform delivery, used to transfer lubricant. Rotodynamic PUMP Centrifugal Rotary Axial flow Positive displacement Reciprocating Reciprocating:- Reciprocating action occurs periodically. Mixed flow Gear Piston Turbine Piston comprises a cylinder and piston, Diaphram comprises flexible diaphram made Lobe Diaphragm from rubber or rubberised febric Plunger comprises plunger, uses crank Sliding Vane Plunger mechanism Pneumatic Handles compressed air. Screw Pneumatic

4 Centrifugal Pumps: Centrifugal pumps p have a rotating impeller, also known as a blade, that is immersed in the liquid. Liquid enters the pump near the axis of the impeller, and the rotating impeller sweeps the liquid out toward the ends of the impeller blades at high pressure. Positive-displacement Pumps: A variety of positive-displacement pumps are also available, generally consisting of arotatingmemberwith a number of lobes that move in a close-fitting casing. The liquid is trapped in the spaces between the lobes and then discharged into a region of higher pressure. A common device of this type is the gear pump, which h consists of a pair of meshing gears. The lobes in this case are the gear teeth A rotodynamic or non- positive displacement pump imparts velocity energy to the fluid, which is converted to pressure energy upon exiting the pump casing. A positive displacement pump moves a fixed volume of fluid within the pump casing by applying a force to moveable boundaries containing the fluid volume. 3

5 Differences between centrifugal pumps, reciprocating pumps and rotary pumps (relatively broad categories) Parameter Optimum Flow and Pressure Applications Maximum Flow Rate Low Flow Rate Capability Centrifugal Pumps Medium/High discharge Capacity, Low/Medium Pressure, small change in pr. Diff. causes a large change in flow 100,000+ GPM No Reciprocating Pumps Low discharge Capacity, High Pressure, pr. Fluctuation doesnot affect discharge 10,000+ GPM Yes Rotary Pumps Low/Medium discharge Capacity, Low/Medium Pressure 10,000+ GPM Maximum Pressure 6,000+ PSI 100,000+ PSI 4,000+ PSI (pound/in ) Requires Pr. Relief Valve Smooth or Pulsating Flow Variable or Constant Flow Self-priming Space Considerations No Smooth Variable No Requires Less Space Yes Pulsating Constant Yes Requires More Space Yes Yes Smooth Constant Yes Requires Less Space Costs Lower Initial Lower Maintenance Higher Power Higher Initial Higher Maintenance Lower Power Lower Initial Lower Maintenance Lower Power Fluid Handling Suitable for a wide range including clean, clear, non-abrasive fluids to fluids with abrasive, high-solid content. Suitable for clean, clear, nonabrasive fluids. Specially-fitted pumps suitable for abrasiveslurry service. Requires clean, clear, nonabrasive fluid due to close tolerances Not suitable for high viscosity fluids Suitable for high viscosity fluids Optimum performance with high viscosity fluids Lower tolerance for entrained gases (vapour trapped in flowing iquid) Higher tolerance for entrained gases Higher tolerance for entrained gases 5

6 Advantages and Disadvantages of Centrifugal Pump Advantages Disadvantages Simple in construction and cheap. Cannot handle highly viscous fluids Handle liquid with large amounts of efficiently greater than 1000 centipoise solids. (cp). (1P= kgm -1 s -1 ) No metal to metal fits. Cannot be operated at low capacity. No valves involved in pump operation. Cannot be operated at high heads. Maintenance costs are lower. Maximum efficiency holds over a narrow range of conditions. Selection of Pump based on: Cannot operate, if percentage volume of Pressure and capacity (discharge). dissolved gases is greater than 5%. Property of liquid (viscosity, temperature, corrosiveness, grittiness i.e. i erosion for suspended particle). Initial and maintenance cost. Pump duty. Availability of space, size and position of locating the pump. Speed of rotation and power required. Standardization with respect to the type and makes of pumps already available at site.

7 Construction of Centrifugal Pumps Main components: 1. Stationary componets, casing, casing cover and bearings. Rotating components, impeller and shaft. Energy changes occur by virtue of impeller and volute. Liquid is fed into the pump at the center of a rotating impeller (eye) and thrown outward by centrifugal force. The conversion of kinetic energy into pressure energy supplies the pressure difference between the suction side and delivery side of the pump tongue 6

Delivery pipe, strainer and foot valve- centre pipe

. Suction pipe, strainer and foot valve- a regular

vertical/horizontal/diagonal split, segmented casing

increasing in area to the discharge port.

delivery pipe, therefore velocity decreases, pressure

Single stage pumps are made by volute, though they

Circular casings for low head and high capacity.

impeller periphery that convert velocity energy

8 Construction of Centrifugal Pumps 3. Other accessories: 1. Delivery pipe, strainer and foot valve- centre pipe connects the centre (eye) of the impeller to the sump.. Suction pipe, strainer and foot valve- a regular valve is just near the pump outlet serves to control the flow of liquid into delivery pipe. Construction wise: Integral, vertical/horizontal/diagonal split, segmented casing Casing (stationary part) I. Volute casings for a higher head. A volute or spiral casing is a curved funnel increasing in area to the discharge port. Cross-section gradually increases from tongue towards delivery pipe, therefore velocity decreases, pressure increases. Single stage pumps are made by volute, though they have greater eddy loss, i.e. lower efficiency. II. Circular casings for low head and high capacity. have stationary diffusion vanes surrounding the impeller periphery that convert velocity energy (dynamic head) to pressure energy (static head). Pump fitted with guide vane is called diffuser pump p or turbine pump. p III. Whirlpool chamber casings annular space is provided in between volute and impeller- arrest the formation of eddies reduce loss of energy improve efficiency. 6

Construction of Centrifugal Pumps Impeller (rotating element) Three main categories of centrifugal pumps exist Both side shrouded (side plate) plate on one side

Enclosed Semi-open Open Radial flow Head is developed by action of the centrifugal force upon the liquid.

9 Construction of Centrifugal Pumps Impeller (rotating element) Three main categories of centrifugal pumps exist Both side shrouded (side plate) plate on one side vane Axial flow Head is developed by propelling or lift action of the vane on the liquid, similar to the airplane. Enclosed Semi-open Open Radial flow Head is developed by action of the centrifugal force upon the liquid. id Mixed flow Head is developed partly by action of the centrifugal force upon the liquid and partly by axial propulsion. This types of pumps resembles the screw, sometimes called screw impeller, suited for irrigation purpose, where high discharge in low head is required. 7

Construction of Centrifugal Pumps Shape and

(upto 15 m) medium head (15 to 40 m) high

Single stage pump can exceed 40 m, for more

respect to the liquid entrance, pump may be

suction chamber Two stage Double suction pump

deep well, mines) Classification of the pump

10 Construction of Centrifugal Pumps Shape and Number of Vane Usually 6 to 1, shaped like curved, cylindrical or more complex. Working Head and Number of Stages Low head (upto 15 m) medium head (15 to 40 m) high head (over 40 m). Single stage pump can exceed 40 m, for more head multistage pump is required number of impeller in series. Single suction and double suction With respect to the liquid entrance, pump may be onesided suction or two-sided suction, to increase discharge. increase head Multistage pump Semi spiral suction chamber Two stage Double suction pump Shaft Position Single stage single suction pump Eliminate axial thrust, increase discharge Split Case Double suction pump Most pump have horizontal shaft. To accommodate space it may be vertical (for deep well, mines) Classification of the pump may be based on liquid handled, suspended solid, viscous liquid handled, application in irrigation, boiler feed, condensate circulation, power used such as IC engine or electric motor etc.

Construction of Centrifugal Pumps Typical Specification of a Split Case High Flow - Double

stage double suction split casing pump with high capacity and pressure.

Once using check valve, the pump can be self-priming.

Impeller: Brozne, Gray cast iron, Silicon brass, stainless steel Shaft: Stainless steel,

SS304,SS316,Copper,HT00 Pump Sealing Packing seal,mechanical seal Capacity Range 16m 3

11 Construction of Centrifugal Pumps Typical Specification of a Split Case High Flow - Double Suction Centrifugal Pump Overview This Fire Fighting Pump is high flow rate pump single stage double suction split casing pump with high capacity and pressure. Usually temperature can not more than 80 C. Once using check valve, the pump can be self-priming. Main Material Casing: Gray cast iron, ductile cast iron, cast steel. Impeller: Brozne, Gray cast iron, Silicon brass, stainless steel Shaft: Stainless steel, Carbon steel Pump Type Casing Material Impeller Split Casing Pump HT00 (Grey Cast Iron % carbon and 0.3-5% silicon plus manganese, sulphur and phosphorus) (Tensile Strength 00 σb /Mpa ) SS304,SS316,Copper,HT00 Pump Sealing Packing seal,mechanical seal Capacity Range 16m 3 /h~850m 3 /h Head Range 8m~140m Inlet/Outlet diameter Impeller 6"(150mm)~3"(800mm) ( ) Rotary Speed 1450rmp/950rpm/585rpm/730rpm/970rpm NPSH(r).5m~7.5m N.weight 165kgs~550kgs Casing,Pump cover,impeller,shaft, Double Pump Parts suction sealing ring Shaft sleeve,bearing etc Certificate ISO9001:008,CE,TUV

Total Static or vertical lift = h s + h d (1) Suction Head of the Pump (H s ) Vs Ps Vs H s h i h f s h s g g where : h i = loss of head at inlet to suction

12 Heads of Pump: where : V s = Velocity of fluid in the suction pipe. V d = Velocity of fluid in the delivery pipe. Free surface h s = Suction lift. h d = Delivery lift. Total Static or vertical lift = h s + h d (1) Suction Head of the Pump (H s ) Vs Ps Vs H s h i h f s h s g g where : h i = loss of head at inlet to suction pipe (negligible) h fs = loss of head due to friction. h s +hh i +hh fs = head measured by vacuum gauge near suction flange, adjacent to the pump () Delivery Head of the Pump (H d ) Vd Pd V where : h d d +h fd = head measured by pressure Hd hf d hd g g gauge near delivery flange, adjacent to the pump 10

13 Heads of Pump: (3) Total External Head of the Pump against which pump has to work (H) Free surface Ps Vs g Generally discharge velocity head is quite low compared to static head, hence neglected P s /γ P d /γ h (4) Manometric Head is difference of total energy at inlet and exit of pump (H m ) Fluid energy at suction P V g P / V /gh s / s / d d Fluid energy at discharge where h is difference in elevation of two pressure gauge installed at inlet and outlet H ( P / V / gh) ( P / V / g) P / P / m d d s s d s H m is actually differences in pressure gauge reading Another expression of H m considering the external condition is as follows Eventually this expression equals to the Total External Head 10

14 Heads of Pump: (5) Net Positive Suction Head NPSH Free surface Pa=atmospheric pressure on the surface of the fluid in the suction well ṆPSH is suction head at impeller eye; it represents NPSH ( P / P / h h ) head requires to transfer a v s fs For smooth and cavitation free operation. NPSH should have such a value so that flowing fluid does not boil. Velocity Triangle fluid from suction to the impeller. v 1 = velocity of fluid at inlet u 1 = velocity of fthe vane at inlet v r1 = relative velocity of fluid at inlet α = angle between the fluid direction and the vane motion direction v w1 = velocity of whirl at inlet = angle made by v r1 with direction of motion at inlet, inlet vane angle v 1 = velocity of fluid at outlet v f1 = velocity of flow at inlet v w = velocity of whirl at outlet v f = velocity of fflow at outlet t β = angle between v 10 with the direction of motion of vane at outlet ϕ = angle made by v r with vane motion direction at outlet, outlet vane angle h

15 Efficiencies of Pump: (1) Manometric Efficiency (η man ) - ratio of the measured / manometric head to the head imparted by the impeller to water. H m H m man Power at the impeller of the Vwu He pump is more than the power given to the water at outlet of g H m He= Theoretical / Euler Head h the pump. imparted to the fluid Hi Power given to the The ratio of the power given to water at outlet of the pump to WH m water at outlet of the kw W= weight of the water the power available at the impeller is called as manometric pump i.e. Pump Output 1000 = g (Q+q), if no loss efficiency. mentioned, then q=0 Work done by impeller per sec W Vwu Power at the impeller /rotor kw kw manometric gh m 1000 g 1000 efficiency = man () Mechanical Efficiency (η m ) Power at the shaft of the impeller of Vwu W Vw u centrifugal pump is more than the power available at the impeller of the pump. The ratio of the power available in the impeller to the power at the shaft of the g 1000 m S. P. = Shaft Power centrifugal pump is known as mechanical efficiency (95~98%). SP.. (4) Hydraulic Efficiency cy (η h ) Hydraulic Losses refer to energy e consumed by friction and fluid separation in the flow passage. This losses decrease the lift or head developed by the impeller. Hydraulic efficiency is the ratio of manometric head developed by the pump to theoretical or ideal head developed by the pump (Hi). where H i =μh e, μ is slip factor of impeller, if number of blade is infinite, then μ =1. ( for medium and higher discharge Q>0.8 m 3 /ṣ, η v =0.98.) (4) Volumetric Efficiency (η v ) Flow through pump is always associated with a volumetric loss due to leakage effect between the impeller and casing. Fluid leakage occurs due to pressure differential between the pressure and discharge side of the impeller, in the labyrinth seal, gland and stuffing box. volumetric efficiency is the ratio of actual to theoretical discharge. (5) Overall Efficiency (η o ) The ratio of the power output of the pump to the power input to the pump. (η o Varies from 0.7 to 0.85) Hm Hm man h H H Q v ( Q q) o man m WH m o kw S. P o hvm i i e

16 Type of Impeller: Three main categories of impeller due to type of impeller s vane: V U U U =V w Radial vanes, Fig. (a). w Backward vanes, Fig. (b). V V f V r f Forward vanes, Fig. (c). V f = V r V r V V V where : V = absolute velocity of the water. U = Tangential velocity of impeller (peripheral velocity). V r = relative velocity of water to the wheel. V f = velocity of flow. v w = velocity of whirl N = Speed of impeller in (rpm). = angle between v with the direction of motion of vane at outlet = = angle made by v r with direction of motion of vane at outlet, vane angle at outlet where : Fig (a) Γ b = direction of blade circulation Fig (b) V r = Distribution of relative velocity in blade spaces. Fig (c) Distribution of pressure in a certain radial section. V w when β = 90 o, (b) when β < 90 o, the (c) when β > 90 o, the radial curved vanes. Backwards curved vanes. Forwards curved vanes. Due to inertial effect, the liquid which is trapped between the impeller vanes is reluctant to move round with the impeller. This results difference of pressure force across the vane. Therefore, high pressure developed in the leading side and low pressure on the trailing side. This difference is called vane loading which increases with the number of vane. V r U =V w V V f = V r V Velocity diagram For Radial vane V w Slip V r The Γ decreases V r in working side of blade and vice versa. This forms pressure differential which is overcome by torque developed by the drive. (a) (b) (c)

17 Slip factor: On high pressure side: liquid follows the blade contour it leaves blade tangentially. On low pressure side: liquid leaves the vane with a certain circumferential component. As a result liquid leaves at an average angle β which is less than actual geometric blade angle β. Due to deviation in flow path, tangential component get reduced by (V w -V w ) which is called slip of the impeller. The ideal slip coefficient is then defined as the ratio of whirl component with the fluid deviation to the whirl component without fluid deviation Due to real fluid effect (friction and fluid separation on the wall of disc shroud and vanes) the radial velocity may not be uniform around the periphery of the impeller. The net effect of the non-uniform velocity and slip is to reduce Euler Head (H e ) Also further reduction of the losses occurs due to intake loss, friction and separation loss etc Empirical Relations for Slip factor V r U =V w V V f = V r V Velocity diagram For Radial vane V w Slip Loss and actual Head-Q curve V r The major loss considered is shock losses at the impeller inlet caused by the mismatch of fluid and metal angles (a) (b) (c)

18 Velocity Vector Diagram and Assumptions Assumptions: Infinite number of vanes, no energy loss in impeller due to friction and eddy formation. Uniform velocity distribution in narrow passage between two adjacent passages. Fluid enters in the eye in radial/axial direction and whirl component at inlet V w1 = 0, V f1 =V 1 No loss due to shock entry, i.e. Inlet edge of the impeller blades are parallel to the relative velocity. Q The rate of change of angular momentum m ( V r V r V r V r w w1 1) Q ( w w1 1) ( V w r V w 1r 1 ) Therefore, Torque = Q / g ( V g wr Vw1r1) Q Q Energy transfer (E) = torque rotational speed in rad/sec ( Vwr Vw 1r1) ( VwuVw 1u1) g g Energy transfer per unit head i.e. Euler Head (H e ) E / Q ( Vw u Vw 1 u 1 )/ g As whirl component at inlet V w1 = 0, therefore H e ( Vwu Vw 1u1)/ g Vwu / g (=H m, shockless entry) I II III Finally Term I : increase in KE or dynamic head, conversation of dynamic head into ( V V1 ) ( u u1) ( Vr Vr1) static pressure is achieved through retardation in volute casing. H e g g g Term II : increase in static pressure due to centrifugal force, due to rotating fluid from one radius to another Head Capacity relationship Term III : change in KE due to retardation of fluid relative to impeller. V u u w e f cot u Q H u V u cot g g g A For a particular pump running at constant speed, i.e. β, A and u =constant, So, H K K Q (Straight line) e 1 Q ( g ) P QH i.. e Pe AQ BQ For β<90º, cot β is +ve, Q H e For β=90º, cot β is 0, Q H e constant For β>90º, cot β is -ve, Q H e (Main Characteristics Curve)

19 Cavitation and other criteria Multistage Pump: N= number of stage, then Total Head developed = n H m Cavitation: ti Vs ( H atm H v) H s hls NPSH g H H If Critical cavitation factor ( c ) >,then cavitation tato stat start: c N s ( ) Maximum suction lift for a pump is as follows, otherwise vaporization of liquid at inlet of pump take place i.e. cavitation V Hs H H h g s atm v Ls h Ls = frictional head loss in suction pipe, H s = suction pressure head in water (m), H = head developed by pump So, for cavitation free operation c or NPSH ch i.e. Minimum NPSH should be equal to c H Priming When centrifugal pump is not running for some time, the water present in the pump casing and suction pipe flows back to the sump and these spaces get filled with air. Now, when motor is switched on and pump starts running, the head developed is equal to H e of air. Since air water, the head thus generated cannot produce spontaneously the vacuum required to start the pumping action. Accordingly water cannot be sucked in along the suction pipe to reach the impeller. For making the pump deliver water, there need to make the casing, impeller and suction line free from air and fill these spaces with water. This process is called priming. For small pump vent cock is provided to supply the water, and for self priming pump certain arrangement is done to ensure supply of water in suction pipe. Performance characteristics of centrifugal pump Pumps are generally designed for maximum efficiency and that occurs when the pump operates at design speed. A particular characteristics corresponding to the design speed are called operating characteristics. It helps to obtain design discharge, head corresponding to the point of maximum efficiency. Operating Characteristics Muschel Curve for pump Muschel curve depicts the performance of the pump over its entire range of operation. Data for plotting these curves is obtained from main characteristics curve curves η vs Q, H vs Q. It helps to locate the region where pump would operate with maximum efficiency.

20 Detection of Pump Problems during operation

21 The Affinity Law The affinity laws for pumps/fans are used in hydraulics to express the relationship between variables involved in pump or fan performance (such as head, volumetric flow rate, shaft speed) and power. They apply to pumps, fans, and hydraulic turbines. In these rotary implements, the affinity laws apply both to centrifugal and axial flows. The affinity laws are useful as they allow prediction of the head discharge characteristic of a pump or fan from a known characteristic measured at a different speed or impeller diameter. The only requirement is that the two pumps or fans are dynamically similar, that is the ratios of the fluid forced are the same. Formulas for Refiguring Pump Performance with Impeller Diameter or Speed Change Similarity relationship Diameter Change Only Speed Change Only Diameter and Speed Change Q D N Q1 D1 N1 Q Q H D N H1 D1 N1 P D N P1 D1 N1 H H P P N Q D N Q1 D1 1 1 N N 1 1 N N 1 1 H H P P D D 1 1 D D 1 1 H constant DN Q constant 3 DN P constant 5 3 DN Specific Speed for Pump Type of impeller Slow speed radial flow Normal speed radial flow High speed radial flow N Q Specific Speed Ns 3/4 Specific Speed H 365N 3.65N Q As per BIS Code: Speed of a Geometrically similar pump capable of lifting 75 kg of Specific Speed (IS code) Ns 3/4 H water per second to a height of one meter. Specific Speed has dimension L 3/4 T -3/, N Q Dimensionless specific speed is Ns 3/4 ( gh ) / T ( LT ) Dimension of dimensionless specific speed Ns 3/4 ( LT L) Mixed flow Axial or Propeller

22 Sample Sheet for pump selection Suppose System Requirements: Suction Pipe diameter: (50 NB) Delivery Pipe diameter: 1.5 (40 NB) Motor speed 1450 rpm Head 8 m to 18 m Discharge 8 LPS to 10 LPS Now Select your Pump..

CHAPTER EIGHT P U M P I N G O F L I Q U I D S

CHAPTER EIGHT P U M P I N G O F L I Q U I D S Pupmps are devices for supplying energy or head to a flowing liquid in order to overcome head losses due to friction and also if necessary, to raise liquid