Lecture 23 Date: Multi-port networks Impedance and Admittance Matrix Lossless and Reciprocal Networks

Size: px
Start display at page:

Download "Lecture 23 Date: Multi-port networks Impedance and Admittance Matrix Lossless and Reciprocal Networks"

Transcription

1 Lecture 23 Date: Multi-port networks mpedance and Admittance Matrix Lossless and Reciprocal Networks

2 ntroduction A pair of terminals through which a current may enter or leave a network is known as a port. Two-terminal devices or elements (such as resistors, capacitors, and inductors) result in oneport networks. Most of the circuits we have dealt with so far are two-terminal or one-port circuits. So far, considered the voltage across or current through a single pair of terminals such as the two terminals of a resistor, capacitor, inductor. We have also studied four-terminal or two-port circuits involving op amps, and transformers. A two-port network is an electrical network with two separate ports for input and output.

3 2-port Networks Requirement of Matrix Formulation Current/Voltage Device (more than one port) Current/Voltage NO!! These are called networks What is the way? mpedance or Admittance Matrix. Right? Can we characterie this using an impedance or admittance! n principle, N by N impedance matrix completely characteries a linear N- port device. Effectively, the impedance matrix defines a multi-port device the way a Z L describes a single port device (e.g., a resistor) Linear networks can be completely characteried by parameters measured at the network ports without knowing the content of the networks.

4 Multiport Networks Networks can have any number of ports however, analysis of a 2-port, 3-port or 4-port network is sufficient to explain the theory and the associated concepts. Port + V - 2 Port Network 2 + V 2 - Port 2 The ports can be characteried with many parameters (Z, Y, h, S, ABCD). Each has a specific advantage. For 2-port Network, each parameter set is related to 4 variables: o 2 independent variables for excitation o 2 dependent variables for response

5 The mpedance Matrix Let us consider the following 4-port network: This could be a simple linear device or a large/complex linear system ( ) Either way, the network can be fully described by its impedance matrix V( ) Port- P ( ) 2 2 Port-2 Port-4 ( ) 4 4 V ( ) 4-port Linear Microwave Network 2 2 V ( ) P Port-3 4 4P The arbitrary locations are known as ports of the network 3 3P Four identical cables used to connect this network to the outside world ( ) 3 3 V ( ) 3 3 Each cable has specific location that defines input impedances to the network

6 The mpedance Matrix (contd.) n principle, the current and voltages at the port-n of networks are given as: V ( ) ( ) n n np n n np the simplified formulations are: V V ( ) ( ) n n n np n n n np f we want to say that there exists a nonero current at port- and ero current at all other ports then we can write as: n order to define the elements of impedance matrix, there will be need to measure/determine the V2 Z2 associated voltages and currents at the respective ports. Suppose, if we measure/determine current at port- and then voltage at port-2 then we can define: Trans-impedance Similarly, the trans-impedance parameters Z 3 and Z 4 are: Z V Z V We can define other trans-impedance parameters such as Z 34 as the ratio between the complex values 4 (into port-4) and V 3 (at port-3), given that the currents at all other ports (, 2, and 3) are ero.

7 The mpedance Matrix (contd.) Therefore, the more generic form of trans-impedance is: Z V m n (given that k = 0 for all k n) Open the ports where the current needs to be ero How do we ensure that all but one port current is ero? The ports should be opened! not the cables connected to the ports V Port- We can then define the respective trans-impedances as: Z 4-port Linear Microwave Network V V 2 V 4 m n Port-2 Port V 3 Port-3 (given that all ports k n are open)

8 The mpedance Matrix (contd.) Once we have defined the trans-impedance terms by opening various ports, it is time to formulate the impedance matrix Since the network is linear, the voltage at any port due to all the port currents is simply the coherent sum of the voltage at that port due to each of the currents For example, the voltage at port-3 is: Therefore we can generalie the voltage for N-port network as: Where and V are N V Z m n n vectors given as: V= V, V, V,..., V 2 3 N V3 Z344 Z333 Z322 Z3 T = V = Z,,,..., 2 3 N T The term Z is matrix given by: Z Z Z Z Z2 Z Z Z 2 n m m2 mpedance Matrix

9 The Admittance Matrix Let us consider the 4-port network again: ( ) V( ) Port- P ( ) 2 2 Port-2 Port-4 ( ) 4 4 V ( ) port Linear Microwave Network V ( ) P Port-3 4 4P 3 3P ( ) 3 3 V ( ) 3 3 This can be characteried using admittance matrix if currents are taken as dependent variables instead of voltages The elements of admittance matrix are called trans-admittance parameters Y

10 The Admittance Matrix (contd.) The trans-admittances Y are defined as: m Y (given that V V k = 0 for all k n) t is apparent that the voltage at all but one port must be equal to ero. This can be ensured by shortcircuiting the voltage ports. The ports should be short-circuited! not the cable connected to the ports n V Port- 2 4 mportant Y Z V2 0 4-port Linear Microwave Network V4 0 Port-2 Port-4 3 Port-3 V3 0 Now, since the network is linear, the current at any one port due to all the port voltages is simply the coherent sum of the currents at that port due to each of the port voltages.

11 The Admittance Matrix (contd.) For example, the current at port-3 is: 3 Y34V 4 Y33V 3 Y32V 2 Y3V N Therefore we can generalie the m current for N-port network as: YV n n Where and V are vectors given as: T V= V, V, V,..., V =,,,..., 2 3 N 2 3 N T = YV The term Y is matrix given by: Y Y Y Y2 Y Y Y Y 2 n m m2 Admittance Matrix The values of elements in the admittance matrix are frequency dependents and often it is advisable to describe admittance matrix as: Y ( ) Y2 ( ) Y n( ) Y2( ) Y( ) Ym ( ) Ym 2( ) Y ( )

12 The Admittance Matrix (contd.) You said that: Z s there any relationship between admittance and impedance matrix of a given device? Y Answer: Let us see if we can figure it out! Recall that we can determine the inverse of a matrix. Denoting the matrix inverse of the admittance matrix as Y, we find: Y = Y Y = Y YV YV Y = V = YV We also know: V = Z Z = Y OR Y Z

13 Reciprocal and Lossless Networks We can classify multi-port devices or networks as either lossless or lossy; reciprocal or non-reciprocal. Let s look at each classification individually. Lossless Network A lossless network or device is simply one that cannot absorb power. This does not mean that the delivered power at every port is ero; rather, it means the total power flowing into the device must equal the total power exiting the device. A lossless device exhibits an impedance matrix with an interesting property. Perhaps not surprisingly, we find for a lossless device that the elements of its impedance matrix will be purely reactive: Re( Z ) 0 For a lossless device f the device is lossy, then the elements of the impedance matrix must have at least one element with a real (i.e., resistive) component. Furthermore, we can similarly say that if the elements of an admittance matrix are all purely imaginary (i.e., Re{Y } =0), then the device is lossless.

14 Reciprocal and Lossless Networks (contd.) Reciprocal Network deally, most passive, linear components will turn out to be reciprocal regardless of whether the designer intended it to be or not! Reciprocity is a tremendously important characteristic, as it greatly simplifies an impedance or admittance matrix! Specifically, we find that a reciprocal device will result in a symmetric impedance and admittance matrix, meaning that: Z Z nm Y Y nm For a reciprocal device For example, we find for a reciprocal device that Z 23 =Z 32, and Y 2 =Y 2.

15 Reciprocal and Lossless Networks (contd.) Z= j2 0. j3 j neither lossless nor reciprocal lossless, but not reciprocal Z= j2 j0. j3 j j j j4 j2 j0.5 Z= j2 j 4 j j2 4 j2 j0.5 reciprocal, but not lossless lossless and reciprocal Z= j2 j j4 j j j2 j4 j2 j0.5 Example determine the Y matrix of this twoport device. R β, Z 0 V 2R V2 β, Z 0 2

16 Example (contd.) Step-: Place a short at port 2 β, Z 0 2 V 2R R V2 0 Step-2: Determine currents and 2 Note that after the short was placed at port 2, both resistors are in parallel, with a potential V across each Therefore current is The current 2 equals the portion of current through R but with opposite sign V V 3V 2R R 2R 2 V R

17 Example (contd.) Step-3: Determine the trans-admittances Y and Y 2 Y 3 V 2 2 2R V Y R Note that Y 2 is real and negative This is still a valid physical result, although you will find that the diagonal terms of an impedance or admittance matrix (e.g., Y 22, Z, Y 44 ) will always have a real component that is positive To find the other two trans-admittance parameters, we must move the short and then repeat each of our previous steps!

18 Example (contd.) Step-: Place a short at port V 2 0 2R R V 2 Step-2: Determine currents and 2 Note that after a short was placed at port, resistor 2R has ero voltage across it and thus ero current through it! Therefore: V2 2 R Step-3: 2 V2 R Determine the trans-admittances Y 2 and Y 22 2 Therefore the admittance matrix is: Y= Y V Y 2 22 R V 2 3/2R /R /R /R 2 R s it lossless or reciprocal?

19 Example 2 2 Consider this circuit: + 6 V + V 2 Where the 3-port device is characteried by the impedance matrix: Z= V 3 determine all port voltages V, V 2, V 3 and all currents, 2, 3.

The Impedance Matrix

The Impedance Matrix 0/0/09 The mpedance Matrix.doc /7 The mpedance Matrix Consider the -port microwave device shown below: z ( z ) z z port z z port 0 -port 0 microwave 0 device P z z P z port z P z ( z ) z port 0 ( z ) z

More information

LAB MANUAL EXPERIMENT NO. 7

LAB MANUAL EXPERIMENT NO. 7 LAB MANUAL EXPERIMENT NO. 7 Aim of the Experiment: Concept of Generalized N-port scattering parameters, and formulation of these parameters into 2-port reflection and transmission coefficients. Requirement:

More information

Electric Circuit Theory

Electric Circuit Theory Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 18 Two-Port Circuits Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Contents and Objectives 3 Chapter Contents 18.1 The Terminal Equations

More information

EE 205 Dr. A. Zidouri. Electric Circuits II. Two-Port Circuits Two-Port Parameters. Lecture #42

EE 205 Dr. A. Zidouri. Electric Circuits II. Two-Port Circuits Two-Port Parameters. Lecture #42 EE 05 Dr. A. Zidouri Electric Circuits Two-Port Circuits Two-Port Parameters Lecture #4-1 - EE 05 Dr. A. Zidouri The material to be covered in this lecture is as follows: o ntroduction to two-port circuits

More information

Two Port Networks. Definition of 2-Port Network A two-port network is an electrical network with two separate ports for input and output

Two Port Networks. Definition of 2-Port Network A two-port network is an electrical network with two separate ports for input and output Two Port Networks Definition of 2-Port Network A two-port network is an electrical network with two separate ports for input and output What is a Port? It is a pair of terminals through which a current

More information

Two-Port Networks Introduction

Two-Port Networks Introduction Two-Port Networks ntroduction n general, a network ma have n ports. The current entering one terminal leaves through the other terminal so that the net current entering all ports equals zero. Thus, a two-port

More information

Impedance and Admittance Parameters

Impedance and Admittance Parameters 1/31/011 mpedance and Admittance Parameters lecture 1/ mpedance and Admittance Parameters Say we wish to connect the put of one circuit to the input of another. #1 put port input port # The terms input

More information

Lecture 11 Date:

Lecture 11 Date: Lecture 11 Date: 11.09.014 Scattering Parameters and Circuit Symmetry Even-mode and Odd-mode Analysis Generalized S-Parameters Example T-Parameters Q: OK, but how can we determine the scattering matrix

More information

Lecture #3. Review: Power

Lecture #3. Review: Power Lecture #3 OUTLINE Power calculations Circuit elements Voltage and current sources Electrical resistance (Ohm s law) Kirchhoff s laws Reading Chapter 2 Lecture 3, Slide 1 Review: Power If an element is

More information

A two-port network is an electrical network with two separate ports

A two-port network is an electrical network with two separate ports 5.1 Introduction A two-port network is an electrical network with two separate ports for input and output. Fig(a) Single Port Network Fig(b) Two Port Network There are several reasons why we should study

More information

Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institution of Technology, Madras

Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institution of Technology, Madras Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institution of Technology, Madras Lecture - 32 Network Function (3) 2-port networks: Symmetry Equivalent networks Examples

More information

Matched, Lossless, Reciprocal Devices

Matched, Lossless, Reciprocal Devices /3/7 Matched reciprocal lossless 73 /9 Matched, Lossless, Reciprocal Devices As we discussed earlier, a device can be lossless or reciprocal. In addition, we can likewise classify it as being matched.

More information

Matched, Lossless, Reciprocal Devices

Matched, Lossless, Reciprocal Devices /6/009 Matched reciprocal lossless present / Matched, Lossless, Reciprocal Devices As we discussed earlier, a device can be lossless or reciprocal. In addition, we can likewise classify it as being matched.

More information

Module 13: Network Analysis and Directional Couplers

Module 13: Network Analysis and Directional Couplers Module 13: Network Analysis and Directional Couplers 13.2 Network theory two port networks, S-parameters, Z-parameters, Y-parameters The study of two port networks is important in the field of electrical

More information

Lecture 19 Date:

Lecture 19 Date: Lecture 19 Date: 8.10.014 The Quadrature Hybrid We began our discussion of dividers and couplers by considering important general properties of three- and fourport networks. This was followed by an analysis

More information

Two Port Network. Ram Prasad Sarkar

Two Port Network. Ram Prasad Sarkar Two Port Ram Prasad Sarkar 0 Two Post : Post nput port Two Post Fig. Port Output port A network which has two terminals (one port) on the one side and another two terminals on the opposite side forms a

More information

Single Phase Parallel AC Circuits

Single Phase Parallel AC Circuits Single Phase Parallel AC Circuits 1 Single Phase Parallel A.C. Circuits (Much of this material has come from Electrical & Electronic Principles & Technology by John Bird) n parallel a.c. circuits similar

More information

Lecture 17 Date:

Lecture 17 Date: Lecture 17 Date: 09.03.017 The Quadrature Hybrid We began our discussion of dividers and couplers by considering important general properties of three- and four-port networks. This was followed by an analysis

More information

Microwave Network Analysis Lecture 1: The Scattering Parameters

Microwave Network Analysis Lecture 1: The Scattering Parameters Microwave Network Analysis Lecture : The Scattering Parameters ELC 305a Fall 0 Department of Electronics and Communications Engineering Faculty of Engineering Cairo University Outline Review on Network

More information

Outline. Thermal noise, noise power and noise temperature. Noise in RLC single-ports. Noise in diodes and photodiodes

Outline. Thermal noise, noise power and noise temperature. Noise in RLC single-ports. Noise in diodes and photodiodes 3. Noise 1 Outline Thermal noise, noise power and noise temperature Noise in RLC single-ports Noise in diodes and photodiodes -port and multi-port noise parameters Noise temperature and noise parameter

More information

Chapter 2. Engr228 Circuit Analysis. Dr Curtis Nelson

Chapter 2. Engr228 Circuit Analysis. Dr Curtis Nelson Chapter 2 Engr228 Circuit Analysis Dr Curtis Nelson Chapter 2 Objectives Understand symbols and behavior of the following circuit elements: Independent voltage and current sources; Dependent voltage and

More information

0-2 Operations with Complex Numbers

0-2 Operations with Complex Numbers Simplify. 1. i 10 2. i 2 + i 8 3. i 3 + i 20 4. i 100 5. i 77 esolutions Manual - Powered by Cognero Page 1 6. i 4 + i 12 7. i 5 + i 9 8. i 18 Simplify. 9. (3 + 2i) + ( 4 + 6i) 10. (7 4i) + (2 3i) 11.

More information

Charge The most basic quantity in an electric circuit is the electric charge. Charge is an electrical property of the atomic particles of which matter

Charge The most basic quantity in an electric circuit is the electric charge. Charge is an electrical property of the atomic particles of which matter Basic Concepts of DC Circuits Introduction An electric circuit is an interconnection of electrical elements. Systems of Units 1 Charge The most basic quantity in an electric circuit is the electric charge.

More information

0-2 Operations with Complex Numbers

0-2 Operations with Complex Numbers Simplify. 1. i 10 1 2. i 2 + i 8 0 3. i 3 + i 20 1 i esolutions Manual - Powered by Cognero Page 1 4. i 100 1 5. i 77 i 6. i 4 + i 12 2 7. i 5 + i 9 2i esolutions Manual - Powered by Cognero Page 2 8.

More information

Two-Port Networks Admittance Parameters CHAPTER16 THE LEARNING GOALS FOR THIS CHAPTER ARE THAT STUDENTS SHOULD BE ABLE TO:

Two-Port Networks Admittance Parameters CHAPTER16 THE LEARNING GOALS FOR THIS CHAPTER ARE THAT STUDENTS SHOULD BE ABLE TO: CHAPTER16 Two-Port Networks THE LEARNING GOALS FOR THIS CHAPTER ARE THAT STUDENTS SHOULD BE ABLE TO: Calculate the admittance, impedance, hybrid, and transmission parameter for two-port networks. Convert

More information

TWO-PORT NETWORKS. Enhancing Your Career. Research is to see what everybody else has seen, and think what nobody has thought.

TWO-PORT NETWORKS. Enhancing Your Career. Research is to see what everybody else has seen, and think what nobody has thought. C H A P T E R TWO-PORT NETWORKS 8 Research is to see what everybody else has seen, and think what nobody has thought. Albert Szent-Gyorgyi Enhancing Your Career Career in Education While two thirds of

More information

One-Port Networks. One-Port. Network

One-Port Networks. One-Port. Network TwoPort s Definitions Impedance Parameters dmittance Parameters Hybrid Parameters Transmission Parameters Cascaded TwoPort s Examples pplications OnePort s v i' 1 OnePort pair of terminals at which a signal

More information

Basics of Network Theory (Part-I)

Basics of Network Theory (Part-I) Basics of Network Theory (PartI). A square waveform as shown in figure is applied across mh ideal inductor. The current through the inductor is a. wave of peak amplitude. V 0 0.5 t (m sec) [Gate 987: Marks]

More information

What s Your (real or imaginary) LCR IQ?

What s Your (real or imaginary) LCR IQ? Chroma Systems Solutions, Inc. What s Your (real or imaginary) LCR IQ? 11021, 11025 LCR Meter Keywords:. Impedance, Inductance, Capacitance, Resistance, Admittance, Conductance, Dissipation Factor, 4-Terminal

More information

ECE2262 Electric Circuits. Chapter 1: Basic Concepts. Overview of the material discussed in ENG 1450

ECE2262 Electric Circuits. Chapter 1: Basic Concepts. Overview of the material discussed in ENG 1450 ECE2262 Electric Circuits Chapter 1: Basic Concepts Overview of the material discussed in ENG 1450 1 Circuit Analysis 2 Lab -ECE 2262 3 LN - ECE 2262 Basic Quantities: Current, Voltage, Energy, Power The

More information

Lecture 6: Impedance (frequency dependent. resistance in the s- world), Admittance (frequency. dependent conductance in the s- world), and

Lecture 6: Impedance (frequency dependent. resistance in the s- world), Admittance (frequency. dependent conductance in the s- world), and Lecture 6: Impedance (frequency dependent resistance in the s- world), Admittance (frequency dependent conductance in the s- world), and Consequences Thereof. Professor Ray, what s an impedance? Answers:

More information

Chapter - 7 Power Dividers and Couplers

Chapter - 7 Power Dividers and Couplers 4//7 7_1 Basic Properties of Dividers and Couplers 1/ Chapter - 7 Power Dividers and Couplers One of the most fundamental problems in microwave engineering is how to efficiently divide signal power. 1.

More information

Lecture 13 Date:

Lecture 13 Date: ecture 3 Date: 6.09.204 The Signal Flow Graph (Contd.) Impedance Matching and Tuning Tpe Matching Network Example Signal Flow Graph (contd.) Splitting Rule Now consider the three equations SFG a a b 2

More information

Notes for course EE1.1 Circuit Analysis TOPIC 10 2-PORT CIRCUITS

Notes for course EE1.1 Circuit Analysis TOPIC 10 2-PORT CIRCUITS Objectives: Introduction Notes for course EE1.1 Circuit Analysis 4-5 Re-examination of 1-port sub-circuits Admittance parameters for -port circuits TOPIC 1 -PORT CIRCUITS Gain and port impedance from -port

More information

Some of the different forms of a signal, obtained by transformations, are shown in the figure. jwt e z. jwt z e

Some of the different forms of a signal, obtained by transformations, are shown in the figure. jwt e z. jwt z e Transform methods Some of the different forms of a signal, obtained by transformations, are shown in the figure. X(s) X(t) L - L F - F jw s s jw X(jw) X*(t) F - F X*(jw) jwt e z jwt z e X(nT) Z - Z X(z)

More information

II Transmitter and Receiver Design

II Transmitter and Receiver Design 8/3/6 transmission lines 1/7 II Transmitter and Receiver Design We design radio systems using RF/microwave components. Q: Why don t we use the usual circuit components (e.g., resistors, capacitors, op-amps,

More information

Lecture 23: Basic Properties of Dividers and Couplers.

Lecture 23: Basic Properties of Dividers and Couplers. Whites, EE 48/58 Lecture 23 age of 9 Lecture 23: Basic roperties of Dividers and Couplers. For the remainder of this course we re going to investigate a plethora of microwave devices and circuits both

More information

11. AC Circuit Power Analysis

11. AC Circuit Power Analysis . AC Circuit Power Analysis Often an integral part of circuit analysis is the determination of either power delivered or power absorbed (or both). In this chapter First, we begin by considering instantaneous

More information

Sophomore Physics Laboratory (PH005/105)

Sophomore Physics Laboratory (PH005/105) CALIFORNIA INSTITUTE OF TECHNOLOGY PHYSICS MATHEMATICS AND ASTRONOMY DIVISION Sophomore Physics Laboratory (PH5/15) Analog Electronics Active Filters Copyright c Virgínio de Oliveira Sannibale, 23 (Revision

More information

Lecture 12. Microwave Networks and Scattering Parameters

Lecture 12. Microwave Networks and Scattering Parameters Lecture Microwave Networs and cattering Parameters Optional Reading: teer ection 6.3 to 6.6 Pozar ection 4.3 ElecEng4FJ4 LECTURE : MICROWAE NETWORK AND -PARAMETER Microwave Networs: oltages and Currents

More information

Unit 2: Modeling in the Frequency Domain. Unit 2, Part 4: Modeling Electrical Systems. First Example: Via DE. Resistors, Inductors, and Capacitors

Unit 2: Modeling in the Frequency Domain. Unit 2, Part 4: Modeling Electrical Systems. First Example: Via DE. Resistors, Inductors, and Capacitors Unit 2: Modeling in the Frequency Domain Part 4: Modeling Electrical Systems Engineering 582: Control Systems I Faculty of Engineering & Applied Science Memorial University of Newfoundland January 20,

More information

5. Circulators and Isolators

5. Circulators and Isolators 9/9/006 Circulators and Isolators / 5. Circulators and Isolators Q: All the devices we have studied thus far are reciprocal. Are there such things as non-reciprocal microwave devices? A: HO: The Circulator

More information

4/27 Friday. I have all the old homework if you need to collect them.

4/27 Friday. I have all the old homework if you need to collect them. 4/27 Friday Last HW: do not need to turn it. Solution will be posted on the web. I have all the old homework if you need to collect them. Final exam: 7-9pm, Monday, 4/30 at Lambert Fieldhouse F101 Calculator

More information

Analog Circuits and Systems

Analog Circuits and Systems Analog Circuits and Systems Prof. K Radhakrishna Rao Lecture 5 Analog Signal Processing using One Port Networks, Passive Two Ports and Ideal Amplifiers 1 One Port Devices Passive devices like R, L, C and

More information

Direct Current Circuits. February 18, 2014 Physics for Scientists & Engineers 2, Chapter 26 1

Direct Current Circuits. February 18, 2014 Physics for Scientists & Engineers 2, Chapter 26 1 Direct Current Circuits February 18, 2014 Physics for Scientists & Engineers 2, Chapter 26 1 Kirchhoff s Junction Rule! The sum of the currents entering a junction must equal the sum of the currents leaving

More information

Transmission Lines. Plane wave propagating in air Y unguided wave propagation. Transmission lines / waveguides Y. guided wave propagation

Transmission Lines. Plane wave propagating in air Y unguided wave propagation. Transmission lines / waveguides Y. guided wave propagation Transmission Lines Transmission lines and waveguides may be defined as devices used to guide energy from one point to another (from a source to a load). Transmission lines can consist of a set of conductors,

More information

Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institute of Technology, Madras

Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institute of Technology, Madras Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institute of Technology, Madras Lecture - 34 Network Theorems (1) Superposition Theorem Substitution Theorem The next

More information

Chapter 10: Sinusoidal Steady-State Analysis

Chapter 10: Sinusoidal Steady-State Analysis Chapter 10: Sinusoidal Steady-State Analysis 1 Objectives : sinusoidal functions Impedance use phasors to determine the forced response of a circuit subjected to sinusoidal excitation Apply techniques

More information

Analysis of a single-loop circuit using the KVL method

Analysis of a single-loop circuit using the KVL method Analysis of a single-loop circuit using the KVL method Figure 1 is our circuit to analyze. We shall attempt to determine the current through each element, the voltage across each element, and the power

More information

Chapter 5 Impedance Matching and Tuning

Chapter 5 Impedance Matching and Tuning 3/25/29 section 5_1 Match with umped Elements 1/3 Chapter 5 Impedance Match and Tun One of the most important and fundamental two-port networks that microwave eneers des is a lossless match network (otherwise

More information

TRANSMISSION LINES AND MATCHING

TRANSMISSION LINES AND MATCHING TRANSMISSION LINES AND MATCHING for High-Frequency Circuit Design Elective by Michael Tse September 2003 Contents Basic models The Telegrapher s equations and solutions Transmission line equations The

More information

Four Ports. 1 ENGN4545/ENGN6545: Radiofrequency Engineering L#16

Four Ports. 1 ENGN4545/ENGN6545: Radiofrequency Engineering L#16 Four Ports Theorems of four port networks 180 o and 90 o Hybrids Directional couplers Transmission line transformers, Four port striplines Rat-races, Wilkinsons, Magic-T s Circulators, Diplexers and Filter

More information

ECE 5260 Microwave Engineering University of Virginia. Some Background: Circuit and Field Quantities and their Relations

ECE 5260 Microwave Engineering University of Virginia. Some Background: Circuit and Field Quantities and their Relations ECE 5260 Microwave Engineering University of Virginia Lecture 2 Review of Fundamental Circuit Concepts and Introduction to Transmission Lines Although electromagnetic field theory and Maxwell s equations

More information

2. Basic Components and Electrical Circuits

2. Basic Components and Electrical Circuits 1 2. Basic Components and Electrical Circuits 2.1 Units and Scales The International System of Units (SI) defines 6 principal units from which the units of all other physical quantities can be derived

More information

Consider a simple RC circuit. We might like to know how much power is being supplied by the source. We probably need to find the current.

Consider a simple RC circuit. We might like to know how much power is being supplied by the source. We probably need to find the current. AC power Consider a simple RC circuit We might like to know how much power is being supplied by the source We probably need to find the current R 10! R 10! is VS Vmcosωt Vm 10 V f 60 Hz V m 10 V C 150

More information

EE313 Fall 2013 Exam #1 (100 pts) Thursday, September 26, 2013 Name. 1) [6 pts] Convert the following time-domain circuit to the RMS Phasor Domain.

EE313 Fall 2013 Exam #1 (100 pts) Thursday, September 26, 2013 Name. 1) [6 pts] Convert the following time-domain circuit to the RMS Phasor Domain. Name If you have any questions ask them. Remember to include all units on your answers (V, A, etc). Clearly indicate your answers. All angles must be in the range 0 to +180 or 0 to 180 degrees. 1) [6 pts]

More information

Resonant Matching Networks

Resonant Matching Networks Chapter 1 Resonant Matching Networks 1.1 Introduction Frequently power from a linear source has to be transferred into a load. If the load impedance may be adjusted, the maximum power theorem states that

More information

1. Review of Circuit Theory Concepts

1. Review of Circuit Theory Concepts 1. Review of Circuit Theory Concepts Lecture notes: Section 1 ECE 65, Winter 2013, F. Najmabadi Circuit Theory is an pproximation to Maxwell s Electromagnetic Equations circuit is made of a bunch of elements

More information

mywbut.com Lesson 16 Solution of Current in AC Parallel and Seriesparallel

mywbut.com Lesson 16 Solution of Current in AC Parallel and Seriesparallel esson 6 Solution of urrent in Parallel and Seriesparallel ircuits n the last lesson, the following points were described:. How to compute the total impedance/admittance in series/parallel circuits?. How

More information

.. Use of non-programmable scientific calculator is permitted.

.. Use of non-programmable scientific calculator is permitted. This question paper contains 8+3 printed pages] Roll No. S. No. of Question Paper 7981 Cnique Paper Code 1\;ame of the Paper ~ame of the Course Semester Duration : 3 Hours 2511102 Circuit Analysis [DC-1.1]

More information

Electronics for Analog Signal Processing - II Prof. K. Radhakrishna Rao Department of Electrical Engineering Indian Institute of Technology Madras

Electronics for Analog Signal Processing - II Prof. K. Radhakrishna Rao Department of Electrical Engineering Indian Institute of Technology Madras Electronics for Analog Signal Processing - II Prof. K. Radhakrishna Rao Department of Electrical Engineering Indian Institute of Technology Madras Lecture - 14 Oscillators Let us consider sinusoidal oscillators.

More information

CHAPTER ONE. 1.1 International System of Units and scientific notation : Basic Units: Quantity Basic unit Symbol as shown in table 1

CHAPTER ONE. 1.1 International System of Units and scientific notation : Basic Units: Quantity Basic unit Symbol as shown in table 1 CHAPTER ONE 1.1 International System of Units and scientific notation : 1.1.1 Basic Units: Quantity Basic unit Symbol as shown in table 1 Table 1 1.1.2 Some scientific notations : as shown in table 2 Table

More information

TWO PORT NETWORKS Introduction: A port is normally referred to a pair of terminals of a network through which we can have access to network either for a source for measuring an output We have already seen

More information

Chapter 28. Direct Current Circuits

Chapter 28. Direct Current Circuits Chapter 28 Direct Current Circuits Circuit Analysis Simple electric circuits may contain batteries, resistors, and capacitors in various combinations. For some circuits, analysis may consist of combining

More information

EE 3120 Electric Energy Systems Study Guide for Prerequisite Test Wednesday, Jan 18, pm, Room TBA

EE 3120 Electric Energy Systems Study Guide for Prerequisite Test Wednesday, Jan 18, pm, Room TBA EE 3120 Electric Energy Systems Study Guide for Prerequisite Test Wednesday, Jan 18, 2006 6-7 pm, Room TBA First retrieve your EE2110 final and other course papers and notes! The test will be closed book

More information

15.9 TWO-PORTS* . (15.114) R Thout = v 2a

15.9 TWO-PORTS* . (15.114) R Thout = v 2a 15.9 TWOPORTS* It should be obvious by now that circuits with dependent sources can perform much more interesting and useful signal processing than those constructed solely from twoterminal resistive elements.

More information

Energy stored in a mechanical wave

Energy stored in a mechanical wave Waves 3 1. Energy stored in a mechanical wave. Wave equation revisited - separation of variables 3. Wave on string with fied ends 4. Waves at boundaries 5. mpedance 6. Other eamples: - Lossless transmission

More information

Basic. Theory. ircuit. Charles A. Desoer. Ernest S. Kuh. and. McGraw-Hill Book Company

Basic. Theory. ircuit. Charles A. Desoer. Ernest S. Kuh. and. McGraw-Hill Book Company Basic C m ш ircuit Theory Charles A. Desoer and Ernest S. Kuh Department of Electrical Engineering and Computer Sciences University of California, Berkeley McGraw-Hill Book Company New York St. Louis San

More information

Bridge Measurement 2.1 INTRODUCTION Advantages of Bridge Circuit

Bridge Measurement 2.1 INTRODUCTION Advantages of Bridge Circuit 2 Bridge Measurement 2.1 INTRODUCTION Bridges are often used for the precision measurement of component values, like resistance, inductance, capacitance, etc. The simplest form of a bridge circuit consists

More information

Single-Time-Constant (STC) Circuits This lecture is given as a background that will be needed to determine the frequency response of the amplifiers.

Single-Time-Constant (STC) Circuits This lecture is given as a background that will be needed to determine the frequency response of the amplifiers. Single-Time-Constant (STC) Circuits This lecture is given as a background that will be needed to determine the frequency response of the amplifiers. Objectives To analyze and understand STC circuits with

More information

(1) The open and short circuit required for the Z and Y parameters cannot usually be

(1) The open and short circuit required for the Z and Y parameters cannot usually be ECE 580 Network Theory Scattering Matrix 76 The Scattering Matrix Motivation for introducing the SM: () The open and short circuit required for the Z and Y parameters cannot usually be implemented in actual

More information

Lecture 1. Electrical Transport

Lecture 1. Electrical Transport Lecture 1. Electrical Transport 1.1 Introduction * Objectives * Requirements & Grading Policy * Other information 1.2 Basic Circuit Concepts * Electrical l quantities current, voltage & power, sign conventions

More information

CHAPTER 5 ANALYSIS OF EXTRAPOLATION VOLTAGES

CHAPTER 5 ANALYSIS OF EXTRAPOLATION VOLTAGES CHAPTER 5 ANALYSIS OF EXTRAPOLATION VOLTAGES In the previous chapters, the emphasis was on understanding the acoustical nonlinearities that would corrupt the ideal voltage based linear extrapolation. However,

More information

Annexure-I. network acts as a buffer in matching the impedance of the plasma reactor to that of the RF

Annexure-I. network acts as a buffer in matching the impedance of the plasma reactor to that of the RF Annexure-I Impedance matching and Smith chart The output impedance of the RF generator is 50 ohms. The impedance matching network acts as a buffer in matching the impedance of the plasma reactor to that

More information

Transmission Line Input Impedance

Transmission Line Input Impedance 1/22/23 Transmission e Input Impedance.doc 1/9 Transmission e Input Impedance Consider a lossless le, length, termated with a load. I(z) I + V (z) -, β + V - z z What is the put impedance of this le? Q:

More information

Sinusoidal Steady State Analysis (AC Analysis) Part I

Sinusoidal Steady State Analysis (AC Analysis) Part I Sinusoidal Steady State Analysis (AC Analysis) Part I Amin Electronics and Electrical Communications Engineering Department (EECE) Cairo University elc.n102.eng@gmail.com http://scholar.cu.edu.eg/refky/

More information

2. The following diagram illustrates that voltage represents what physical dimension?

2. The following diagram illustrates that voltage represents what physical dimension? BioE 1310 - Exam 1 2/20/2018 Answer Sheet - Correct answer is A for all questions 1. A particular voltage divider with 10 V across it consists of two resistors in series. One resistor is 7 KΩ and the other

More information

ECE 546 Lecture 13 Scattering Parameters

ECE 546 Lecture 13 Scattering Parameters ECE 546 Lecture 3 Scattering Parameters Spring 08 Jose E. Schutt-Aine Electrical & Computer Engineering University of Illinois jesa@illinois.edu ECE 546 Jose Schutt Aine Transfer Function Representation

More information

E40M Charge, Current, Voltage and Electrical Circuits. M. Horowitz, J. Plummer, R. Howe 1

E40M Charge, Current, Voltage and Electrical Circuits. M. Horowitz, J. Plummer, R. Howe 1 E40M Charge, Current, Voltage and Electrical Circuits M. Horowitz, J. Plummer, R. Howe 1 Understanding the Solar Charger Lab Project #1 We need to understand how: 1. Current, voltage and power behave in

More information

Lecture 12 Date:

Lecture 12 Date: Lecture 12 Date: 09.02.2017 Microstrip Matching Networks Series- and Shunt-stub Matching Quarter Wave Impedance Transformer Microstrip Line Matching Networks In the lower RF region, its often a standard

More information

Electrical Circuits Lab Series RC Circuit Phasor Diagram

Electrical Circuits Lab Series RC Circuit Phasor Diagram Electrical Circuits Lab. 0903219 Series RC Circuit Phasor Diagram - Simple steps to draw phasor diagram of a series RC circuit without memorizing: * Start with the quantity (voltage or current) that is

More information

Waves on Lines. Contents. ! Transmission Lines! The Smith Chart! Vector Network Analyser (VNA) ! Measurements

Waves on Lines. Contents. ! Transmission Lines! The Smith Chart! Vector Network Analyser (VNA) ! Measurements Waves on Lines If the wavelength to be considered is significantly greater compared to the size of the circuit the voltage will be independent of the location. amplitude d! distance but this is not true

More information

Impedance Measurements for Successful Device Modeling

Impedance Measurements for Successful Device Modeling Impedance Measurements for Successful Device Modeling - A Lab Book Emphasizing Practice - (C) Franz Sischka, Nov. 2018 www.sisconsult.de -1- Outline The Impedance Plane Z = R + j*x and Typical Impedance

More information

Chapter 6 DIRECT CURRENT CIRCUITS. Recommended Problems: 6,9,11,13,14,15,16,19,20,21,24,25,26,28,29,30,31,33,37,68,71.

Chapter 6 DIRECT CURRENT CIRCUITS. Recommended Problems: 6,9,11,13,14,15,16,19,20,21,24,25,26,28,29,30,31,33,37,68,71. Chapter 6 DRECT CURRENT CRCUTS Recommended Problems: 6,9,,3,4,5,6,9,0,,4,5,6,8,9,30,3,33,37,68,7. RESSTORS N SERES AND N PARALLEL - N SERES When two resistors are connected together as shown we said that

More information

Schedule. ECEN 301 Discussion #20 Exam 2 Review 1. Lab Due date. Title Chapters HW Due date. Date Day Class No. 10 Nov Mon 20 Exam Review.

Schedule. ECEN 301 Discussion #20 Exam 2 Review 1. Lab Due date. Title Chapters HW Due date. Date Day Class No. 10 Nov Mon 20 Exam Review. Schedule Date Day lass No. 0 Nov Mon 0 Exam Review Nov Tue Title hapters HW Due date Nov Wed Boolean Algebra 3. 3.3 ab Due date AB 7 Exam EXAM 3 Nov Thu 4 Nov Fri Recitation 5 Nov Sat 6 Nov Sun 7 Nov Mon

More information

Single- and Multiport Networks. RF Electronics Spring, 2018 Robert R. Krchnavek Rowan University

Single- and Multiport Networks. RF Electronics Spring, 2018 Robert R. Krchnavek Rowan University Single- and Multiport Networks RF Electronics Spring, 208 Robert R. Krchnavek Rowan University Objectives Generate an understanding of the common network representations of Z, Y, h, and ABCD. To be able

More information

Transmission lines. Shouri Chatterjee. October 22, 2014

Transmission lines. Shouri Chatterjee. October 22, 2014 Transmission lines Shouri Chatterjee October 22, 2014 The transmission line is a very commonly used distributed circuit: a pair of wires. Unfortunately, a pair of wires used to apply a time-varying voltage,

More information

ABSTRACT INTRODUCTION

ABSTRACT INTRODUCTION Design of Stable Fuzzy-logic-controlled Feedback Systems P.A. Ramamoorthy and Song Huang Department of Electrical & Computer Engineering, University of Cincinnati, M.L. #30 Cincinnati, Ohio 522-0030 FAX:

More information

PHYS225 Lecture 9. Electronic Circuits

PHYS225 Lecture 9. Electronic Circuits PHYS225 Lecture 9 Electronic Circuits Last lecture Field Effect Transistors Voltage controlled resistor Various FET circuits Switch Source follower Current source Similar to BJT Draws no input current

More information

y(d) = j

y(d) = j Problem 2.66 A 0-Ω transmission line is to be matched to a computer terminal with Z L = ( j25) Ω by inserting an appropriate reactance in parallel with the line. If f = 800 MHz and ε r = 4, determine the

More information

Chapter 2 Direct Current Circuits

Chapter 2 Direct Current Circuits Chapter 2 Direct Current Circuits 2.1 Introduction Nowadays, our lives are increasingly dependent upon the availability of devices that make extensive use of electric circuits. The knowledge of the electrical

More information

Kirchhoff's Laws and Circuit Analysis (EC 2)

Kirchhoff's Laws and Circuit Analysis (EC 2) Kirchhoff's Laws and Circuit Analysis (EC ) Circuit analysis: solving for I and V at each element Linear circuits: involve resistors, capacitors, inductors Initial analysis uses only resistors Power sources,

More information

Transient Analysis of Interconnects by Means of Time-Domain Scattering Parameters

Transient Analysis of Interconnects by Means of Time-Domain Scattering Parameters Transient Analysis of Interconnects by Means of Time-Domain Scattering Parameters Wojciech Bandurski, Poznań Univ. of Technology 60-965 Poznań, Piotrowo 3a, Poland, bandursk@zpe.iee.put.poznan.pl INTRODUCTION

More information

EE Branch GATE Paper 2010

EE Branch GATE Paper 2010 Q.1 Q.25 carry one mark each 1. The value of the quantity P, where, is equal to 0 1 e 1/e 2. Divergence of the three-dimensional radial vector field is 3 1/r 3. The period of the signal x(t) = 8 is 0.4

More information

ENGG 225. David Ng. Winter January 9, Circuits, Currents, and Voltages... 5

ENGG 225. David Ng. Winter January 9, Circuits, Currents, and Voltages... 5 ENGG 225 David Ng Winter 2017 Contents 1 January 9, 2017 5 1.1 Circuits, Currents, and Voltages.................... 5 2 January 11, 2017 6 2.1 Ideal Basic Circuit Elements....................... 6 3 January

More information

Homework 2 SJTU233. Part A. Part B. Problem 2. Part A. Problem 1. Find the impedance Zab in the circuit seen in the figure. Suppose that R = 5 Ω.

Homework 2 SJTU233. Part A. Part B. Problem 2. Part A. Problem 1. Find the impedance Zab in the circuit seen in the figure. Suppose that R = 5 Ω. Homework 2 SJTU233 Problem 1 Find the impedance Zab in the circuit seen in the figure. Suppose that R = 5 Ω. Express Zab in polar form. Enter your answer using polar notation. Express argument in degrees.

More information

RF AND MICROWAVE ENGINEERING

RF AND MICROWAVE ENGINEERING RF AND MICROWAVE ENGINEERING EC6701 RF AND MICROWAVE ENGINEERING UNIT I TWO PORT RF NETWORKS-CIRCUIT REPRESENTATION 9 Low frequency parameters-impedance,admittance, hybrid and ABCD. High frequency parameters-formulation

More information

LINEAR CIRCUIT ANALYSIS (EED) U.E.T. TAXILA 09

LINEAR CIRCUIT ANALYSIS (EED) U.E.T. TAXILA 09 LINEAR CIRCUIT ANALYSIS (EED) U.E.T. TAXILA 09 ENGR. M. MANSOOR ASHRAF INTRODUCTION Thus far our analysis has been restricted for the most part to dc circuits: those circuits excited by constant or time-invariant

More information

Lecture 5: Using electronics to make measurements

Lecture 5: Using electronics to make measurements Lecture 5: Using electronics to make measurements As physicists, we re not really interested in electronics for its own sake We want to use it to measure something often, something too small to be directly

More information

2.004 Dynamics and Control II Spring 2008

2.004 Dynamics and Control II Spring 2008 MIT OpenCourseWare http://ocwmitedu 00 Dynamics and Control II Spring 00 For information about citing these materials or our Terms of Use, visit: http://ocwmitedu/terms Massachusetts Institute of Technology

More information