PHASED OUT. FL ballasts Electronic dimming. PCA TC BASIC Y II, W BASIC compact

Transcription

1 EL Product description Processor-controlled ballast with y II inside Highest possible energy class CELMA EEI = A BAT Noise-free precise control via DSI signal, switchdim or corridorfunction Nominal life up to 00,000 h (at ta 50 C with a failure rate max. 0. % per,000 h) 5-year guarantee Interfaces DSI switchdim (with memory function) corridorfunction ( preprogrammed profiles) Integrated SMART interface for function with SMART Sensor 5D 9f and corridorfunction plugs Functions Intelligent Temperature Guard (overtemperature protection) Intelligent Voltage Guard (overvoltage indication and undervoltage shutdown) Optimum filament heating in any dimmer setting Disconnection of filament heating from a dimming level of approx. 90 % for maximum energy efficiency (SMART-Heating concept) corridorfunction with ambient light control Automatically triggered emergency lighting value in DC mode, 5 % For emergency lighting systems as per EN 507 Automatic start after replacement of defective lamps Automatic shutdown if the lamp is faulty È Standards, page TC-DEL TC-SEL TC-TEL TC-TEL HE TC-F TC-L Wiring diagrams and installation examples, page 8 TC-DD T5c PCA TC BASIC Y II, 57 W BASIC compact 4, 4, 99 0,5 ±0, 99 0,5 ±0, ±0, 6,5 ±0, 6,5 89,5 Technical data Mains voltage range 0 40 V AC voltage range V DC voltage range V (lamp start 98 V DC) Mains frequency 0 / 50 / 60 Hz Overvoltage protection 0 V AC, h Typ. power input on standby < 0. W Protective hot restart 0.5 s for AC / 0. s for DC Dimming range 0 00 % Lamp start possible from 0 % Operating frequency ~ 40 0 khz Type of protection IP0 66,5 0±0, 79±0,

2 Specific technical data Lamp wattage Lamp type Type For luminaires with lamp Article number Ordering data Dimensions L x W x H Lamp power Circuit power EEI Current at 50 Hz 0 V λ at 50 Hz 0 V tc point max. Ambient temperature ta x W TC-SEL PCA x/ TC BASIC Y II 858 x 79 x mm.0 W.5 W A 0.06 A C C x W TC-TEL HE PCA x/ TC BASIC Y II 858 x 79 x mm.5 W.0 W A 0.07 A C C x W TC-DEL PCA x/ TC BASIC Y II 858 x 79 x mm.5 W.5 W A BAT 0.07 A C C x W TC-TEL PCA x/ TC BASIC Y II 858 x 79 x mm.5 W 4.0 W A BAT 0.07 A C C x 4 W TC-TEL HE PCA x/ TC BASIC Y II 858 x 79 x mm 4.5 W 6.0 W A BAT 0.08 A C C x 7 W TC-TEL HE PCA x/ TC BASIC Y II 858 x 79 x mm 7.5 W 9.0 W A BAT 0.09 A C C x 8 W TC-DEL PCA x8 TC BASIC Y II 854 x 79 x mm 6.5 W 9.0 W A BAT 0.09 A C C x 8 W TC-TEL PCA x8 TC BASIC Y II 854 x 79 x mm 6.5 W 8.5 W A BAT 0.09 A C C x 8 W TC-F PCA x8/4 TCL BASIC c Y II 855 x 79 x mm 5.0 W 8.5 W A BAT 0.08 A C C x 8 W TC-L PCA x8/4 TCL BASIC c Y II 855 x 79 x mm 6.0 W 8.5 W A BAT 0.08 A C C x W T5c PCA x8/4 TCL BASIC c Y II 855 x 79 x mm.0 W 5.0 W A BAT 0. A C C x 4 W TC-F PCA x8/4 TCL BASIC c Y II 855 x 79 x mm 0.0 W 4.5 W A BAT 0. A C C x 4 W TC-L PCA x8/4 TCL BASIC c Y II 855 x 79 x mm 6.0 W 4.5 W A BAT 0. A C C x 6 W TC-DEL PCA x6-57 TC BASIC Y II 85 x 79 x mm 4.0 W 6.5 W A BAT 0. A C C x 6 W TC-TEL PCA x6-57 TC BASIC Y II 85 x 79 x mm 4.0 W 7.0 W A BAT 0. A C C x W TC-TEL PCA x6-57 TC BASIC Y II 85 x 79 x mm.0 W 5.0 W A BAT 0.5 A C C x 40 W T5c PCA x6-57 TC BASIC Y II 85 x 79 x mm 40.0 W 4.0 W A BAT 0.6 A C C x 40 W TC-L PCA x6-57 TC BASIC Y II 85 x 79 x mm 40.0 W 4.0 W A BAT 0.8 A C C x 4 W TC-TEL PCA x6-57 TC BASIC Y II 85 x 79 x mm 4.0 W 44.0 W A BAT 0.0 A C C x 57 W TC-TEL PCA x6-57 TC BASIC Y II 85 x 79 x mm 57.0 W 6.0 W A BAT 0.4 A C C x 8 W TC-DD PCA x8 TC-DD BASIC Y II 8556 x 79 x mm 6.5 W 7.5 W A BAT 0. A C C x 55 W T5c PCA x55 T5c BASIC Y II 856 x 79 x mm 55.0 W 59.0 W A BAT 0.6 A C C For luminaires with lamps x W TC-SEL PCA x/ TC BASIC Y II 859 x 0 x mm.0 W 4.5 W A BAT 0. A C C x W TC-TEL HE PCA x/ TC BASIC Y II 859 x 0 x mm.5 W 6.0 W A BAT 0. A C C x W TC-DEL PCA x/ TC BASIC Y II 859 x 0 x mm 5.0 W 7.0 W A BAT 0. A C C x W TC-TEL PCA x/ TC BASIC Y II 859 x 0 x mm 5.0 W 7.5 W A BAT 0. A C C x 4 W TC-TEL HE PCA x/ TC BASIC Y II 859 x 0 x mm 9.0 W.0 W A BAT 0.5 A C C x 7 W TC-TEL HE PCA x/ TC BASIC Y II 859 x 0 x mm 5.0 W 7.5 W A BAT 0.7 A C C x 8 W TC-DEL PCA x8 TC BASIC Y II 855 x 0 x mm.0 W 6.0 W A BAT 0.7 A C C x 8 W TC-TEL PCA x8 TC BASIC Y II 855 x 0 x mm.0 W 6.0 W A BAT 0.7 A C C x 8 W TC-F PCA x8/4 TCL BASIC c Y II 8559 x 0 x mm 5.0 W 7.0 W A BAT 0.5 A C C x 8 W TC-L PCA x8/4 TCL BASIC c Y II 8559 x 0 x mm 6.0 W 7.0 W A BAT 0.6 A C C x 4 W TC-F PCA x8/4 TCL BASIC c Y II 8559 x 0 x mm 0.0 W 48.0 W A BAT 0. A C C x 4 W TC-L PCA x8/4 TCL BASIC c Y II 8559 x 0 x mm.0 W 48.0 W A BAT 0. A C C x 6 W TC-DEL PCA x6//4 TC BASIC Y II 85 x 0 x mm 48.0 W 5.0 W A BAT 0.4 A C C x 6 W TC-TEL PCA x6//4 TC BASIC Y II 85 x 0 x mm 48.0 W 5.0 W A BAT 0.4 A C C x W TC-TEL PCA x6//4 TC BASIC Y II 85 x 0 x mm 64.0 W 68.0 W A BAT 0.9 A C C x 4 W TC-TEL PCA x6//4 TC BASIC Y II 85 x 0 x mm 84.0 W 88.5 W A BAT 0.9 A C C According to the EU directives on ecodesign requirements (EC) No. 45/009 and (EC) No. 47/00. Valid at 00 % dimming level. +0 C to ta max: unrestricted dimming. -5 C to +0 C: unrestricted dimming from 00 % to 0 %. -5 C to +0 C, dimming below 0 %: malfunction possible but no damage to ECG. This applies to AC and DC operation. Type Article number Packaging, carton Packaging, pallet Weight per pc. For luminaires with lamp PCA x/ TC BASIC Y II pc(s). 500 pc(s) kg PCA x8 TC BASIC Y II pc(s). 500 pc(s) kg PCA x8/4 TCL BASIC c Y II pc(s). 500 pc(s) kg PCA x6-57 TC BASIC Y II 85 0 pc(s). 500 pc(s). 0.6 kg PCA x8 TC-DD BASIC Y II pc(s). 500 pc(s) kg PCA x55 T5c BASIC Y II pc(s). 500 pc(s). 0.6 kg For luminaires with lamps PCA x/ TC BASIC Y II pc(s). 500 pc(s) kg PCA x8 TC BASIC Y II pc(s). 500 pc(s) kg PCA x8/4 TCL BASIC c Y II pc(s). 500 pc(s). 0.0 kg PCA x6//4 TC BASIC Y II 85 0 pc(s). 500 pc(s) kg

3 Standards EN 5505 EN 6099 EN EN EN 6547 Suitable for emergency installations according EN 507 CISPR 5 CISPR IEC 6099 IEC IEC IEC 6547 Lamp starting characteristics Warm start Starting time 0.5 s with AC Starting time 0. s with DC Start at dimming level from 0 00 % AC operation Mains voltage 0 40 V 50/60 Hz V 50/60 Hz including safety tolerance (±0 %) V 50/60 Hz including performance tolerance (+6 % / -8 %) DC operation 0 40 V 0 Hz V 0 Hz certain lamp start V 0 Hz operating range Use in emergency lighting installations according to EN 507 or for emergency luminaires according to EN appendix J. Light output level in DC operation Default value is 5 % Emergency units The PCA TC BASIC y II ballasts are compatible with all emergency units from Tridonic. See the table in the data sheet. Also all 5-pole emergency units can be used. When used with other emergency units tests are necessary. Temperature range Unlimited dimming range from 0 C to ta max. -5 C to 0 C: unlimited dimming operation from 00 % bis 0 %. If dimm level goes below 0 % malfunction possible, but no electronic ballast damage. This applies to AC and DC operation. Mains currents in DC operation (at 5 % light output) Type Lamp type Wattage Mains current at Un = 0 VDC Mains current at Un = 75 VDC TC-SEL x W 0.04 A 0.0 A TC-TEL HE x W 0.04 A 0.0 A PCA x/ TC BASIC Y II TC-DEL x W 0.04 A 0.0 A TC-TEL x W 0.04 A 0.0 A TC-TEL HE x 4 W 0.04 A 0.04 A TC-TEL HE x 7 W 0.04 A 0.04 A PCA x8 TC BASIC Y II TC-DEL x 8 W 0.05 A 0.04 A TC-TEL x 8 W 0.04 A 0.04 A TC-F x 8 W 0.04 A 0.04 A TC-L x 8 W 0.04 A 0.04 A PCA x8/4 TCL BASIC c Y II T5c x W 0.06 A 0.05 A TC-F x 4 W 0.05 A 0.04 A TC-L x 4 W 0.05 A 0.05 A TC-DEL x 6 W 0.06 A 0.05 A TC-TEL x 6 W 0.06 A 0.05 A TC-TEL x W 0.06 A 0.06 A PCA x6-57 TC BASIC Y II T5c x 40 W 0.07 A 0.06 A TC-L x 40 W 0.07 A 0.07 A TC-TEL x 4 W 0.07 A 0.07 A TC-TEL x 57 W 0.09 A 0.08 A PCA x8 TC-DD BASIC Y II TC-DD x 8 W 0.06 A 0.05 A PCA x55 T5c BASIC Y II T5c x 55 W 0.0 A 0.09 A TC-SEL x W 0.05 A 0.05 A TC-TEL HE x W 0.06 A 0.05 A PCA x/ TC BASIC Y II TC-DEL x W 0.06 A 0.05 A TC-TEL x W 0.06 A 0.05 A TC-TEL HE x 4 W 0.06 A 0.06 A TC-TEL HE x 7 W 0.07 A 0.06 A PCA x8 TC BASIC Y II TC-DEL x 8 W 0.07 A 0.07 A TC-TEL x 8 W 0.07 A 0.06 A TC-F x 8 W 0.07 A 0.05 A PCA x8/4 TCL BASIC c Y II TC-L x 8 W 0.07 A 0.06 A TC-F x 4 W 0.09 A 0.07 A TC-L x 4 W 0.04 A 0.07 A TC-DEL x 6 W 0. A 0.09 A PCA x6//4 TC BASIC Y II TC-TEL x 6 W 0.0 A 0.09 A TC-TEL x W 0. A 0.0 A TC-TEL x 4 W 0. A 0. A

4 Ballast lumen factor AC operation (AC-BLF) EN Type Lamp type Wattage AC-BLF at U = 0 VAC TC-SEL x W.04 TC-TEL HE x W.05 PCA x/ TC BASIC Y II TC-DEL x W.00 TC-TEL x W 0.99 TC-TEL HE x 4 W.05 TC-TEL HE x 7 W.06 PCA x8 TC BASIC Y II TC-DEL x 8 W.0 TC-TEL x 8 W.0 TC-F x 8 W 0.07 TC-L x 8 W 0.97 PCA x8/4 TCL BASIC c Y II T5c x W.0 TC-F x 4 W.0 TC-L x 4 W.0 TC-DEL x 6 W.00 TC-TEL x 6 W.0 TC-TEL x W 0.98 PCA x6-57 TC BASIC Y II T5c x 40 W 0.96 TC-L x 40 W 0.96 TC-TEL x 4 W.00 TC-TEL x 57 W 0.98 PCA x8 TC-DD BASIC Y II TC-DD x 8 W.0 PCA x55 T5c BASIC Y II T5c x 55 W.00 TC-SEL x W.04 TC-TEL HE x W.04 PCA x/ TC BASIC Y II TC-DEL x W 0.99 TC-TEL x W 0.98 TC-TEL HE x 4 W.04 TC-TEL HE x 7 W.04 PCA x8 TC BASIC Y II TC-DEL x 8 W.0 TC-TEL x 8 W.0 TC-F x 8 W 0.94 PCA x8/4 TCL BASIC c Y II TC-L x 8 W 0.94 TC-F x 4 W.0 TC-L x 4 W.0 TC-DEL x 6 W.00 PCA x6//4 TC BASIC Y II TC-TEL x 6 W.0 TC-TEL x W 0.97 TC-TEL x 4 W 0.99 The ballast lumen factor for AC operation (AC-BLF) does not alter from Un = 98 V AC to Un = 54 V AC. The ballast lumen factor for DC operation (DC-BLF) on the basis of an automatic power reduction of the ballasts (default value is 5 %) will be smaller than AC. It does not alter in the DC operating range (98 80 V DC). 4

5 Dimming Dimming curve is adapted to the eye sensitiveness. Dimming range 0 % to 00 % Digital control with DSI signal: 8 bit Manchester Code Speed 0 % to 00 % in 0.8 s Control input (D, D) Digital DSI signal, push-to-make switch (switchdim) or a motion detector (corridorfunction) can be wired on the same terminals (D and D). Digital signal DSI The control input is non-polar and protected against accidental connection with a mains voltage up to 64 V. The control signal is not SELV. Control cable has to be installed in accordance to the requirements of low voltage installations. Different functions depending on each module. SMART interface An additional interface for the direct connection of the SMART-Sensor 5D 9f ) or corridorfunction plugs. Application and functionallity see corridorfunction user manual. SMART-Sensor 5D 9f ) light sensor operating mode: The sensor registers actual ambient light and maintains the individually defined constant lux level. After every mains reset the SMART interface automatically checks for an installed sensor. With the sensor installed the PCA TC BASIC y II automatically runs in the constant lux level mode. ON/OFF switch via mains, switchdim or DSI signal. DSI signal = 0 switches off, DSI signal switches on. With switchdim signals it is possible to change the controlled light level temporarily. Temporarily means that after a switching cycle OFF/ ON command the ballast will start at the preset value determined by the SAMRT-Sensor 5D 9f. The installation of the two wire bus is according to the appropriate low voltage regulations. ) SMART-Sensor 5D 9f: article number switchdim Integrated switchdim function allows a direct connection of a push to make switch for dimming and switching. Brief push (< 0.6 s) switches ballast ON and OFF. The ballasts switch-on at light level set at switch-off. After switch ON the last settet dimming level will be activated again. When the push to make switch is held, PCA ballasts are dimmed. After repush the PCA is dimmed in the opposite direction. The switchdim fade time is s from min. to max. in the factory settings. In installations with PCAs with different dimming levels or opposite dimming directions (e.g. after a system extension), all PCAs can be synchronized to 50 % dimming level by a 0 s push. Use of push to make switch with indicator lamp is not permitted. switchdim and corridorfunction are very simple tools for controlling ballasts with conventional momentaryaction switches or motion sensors. To ensure correct operation a sinusoidal mains voltage with a frequency of 50 Hz or 60 Hz is required at the control input. Dimming characteristics PCA TC BASIC Y II Energy saving PCA TC BASIC Y II digital dimming value mains power in % DSI relative lighting level in % dimming level in % Dimming characteristics as seen by the human eye Note: The dimming level of BASIC can be different to the graphic (dimming level 0 to 00 %) Special attention must be paid to achieving clear zero crossings. Serious mains faults may impair the operation of switchdim and corridorfunction. corridorfunction To activate the corridorfunction a voltage of 0 V simply has to be applied for five minutes at switchdim connection. The unit will then switch automatically to the corridorfunction. Note: If the corridorfunction is wrongly activated in a switchdim system (for example a switch is used instead of pushbutton), there is the option of installing a pushbutton and deactivating the corridorfunction mode by five short pushes of the button within three seconds. The corridorfunction offers the added benefit of a second and third preprogrammed profile, which can be activated by the corridorfunction plugs. It is also possible to combine the corridorfunction with the SMART-Sensor 5D 9f light sensor. Application and functionallity of profiles see user manual of the corridorfunction. switchdim PCA TC BASIC Y II DSI PCA TC BASIC Y II Dimmable ballasts from Tridonic have to be earthed. D D D 5 D 6 corridorfunction PCA TC BASIC Y II D 5 D N L N L DSI 5

6 Loading of automatic circuit breakers (Limitation via inrush current) Automatic circuit breaker type C0 C C6 C0 B0 B B6 B0 Inrush current (.5 mm ) Inrush current (.5 mm ) Installation Ø.5 mm.5 mm.5 mm.5 mm.5 mm.5 mm.5 mm.5 mm I max time I max time PCA x/ TC BASIC Y II A 5 µs. A 57 µs PCA x8 TC BASIC Y II A 47 µs 4.5 A 50 µs PCA x8/4 TCL BASIC c Y II A 06 µs 5.6 A 99 µs PCA x6-57 TC BASIC Y II A µs 0.4 A µs PCA x8 TC-DD BASIC Y II A 89 µs 8.8 A 7 µs PCA x55 T5c BASIC Y II A 40 µs 7.5 A 5 µs PCA x/ TC BASIC Y II A 89 µs.7 A 86 µs PCA x8 TC BASIC Y II A 8 µs 9.7 A 45 µs PCA x8/4 TCL BASIC c Y II A 55 µs 7. A 45 µs PCA x6//4 TC BASIC Y II A 48 µs 6.4 A 4 µs Continuous operation: to calculate the protective saftey switch see main current, page Intelligent Voltage Guard Intelligent Voltage Guard is the name of the electronic monitor from Tridonic. This inno vative feature of the PCA family of control gear from Tridonic immediately shows if the mains voltage rises above certain thresholds. Measures can then be taken quickly to prevent damage to the control gear. Harmonic distortion in the mains supply (at 0 V / 50 Hz) If the mains voltage rises above approx. 8 Vrms (voltage depends on the ballast type), the lamp starts flashing on and off. To avoid a damage of the device the mains supply has to be switched off at this signal. Type Lamp type Wattage THD TC-SEL x W 0 4 TC-TEL HE x W 0 4 PCA x/ TC BASIC Y II TC-DEL x W 0 4 TC-TEL x W 0 4 TC-TEL HE x4 W 9 5 TC-TEL HE x7 W 8 5 PCA x8 TC BASIC Y II TC-DEL x8 W 9 7 TC-DEL x8 W 9 7 TC-F x8 W 0 4 TC-L x8 W 9 4 PCA x8/4 TCL BASIC c Y II T5c x W 8 4 TC-F x4 W 8 4 TC-L x4 W 7 4 TC-DEL x6 W 0 6 TC-TEL x6 W 0 5 TC-TEL x W 9 6 PCA x6-57 TC BASIC Y II T5c x40 W 9 6 TC-L x40 W 9 6 TC-TEL x4 W 7 5 TC-TEL x57 W 7 6 PCA x8 TC-DD BASIC Y II TC-DD x8 W 9 6 PCA x55 T5c BASIC Y II T5c x55 W 8 4 TC-SEL x W TC-TEL HE x W PCA x/ TC BASIC Y II TC-DEL x W TC-TEL x W TC-TEL HE x4 W 8 4 TC-TEL HE x7 W 8 5 PCA x8 TC BASIC Y II TC-DEL x8 W 9 6 TC-TEL x8 W 9 6 TC-F x8 W 9 5 PCA x8/4 TCL BASIC c Y II TC-L x8 W 9 5 TC-F x4 W 7 5 TC-L x4 W 7 5 TC-DEL x6 W 0 6 PCA x6//4 TC BASIC Y II TC-TEL x6 W 0 7 TC-TEL x W 9 7 TC-TEL x4 W 8 7 Intelligent Temperature Guard The intelligent temperature guard protects the PCA TC BASIC y II from thermal overheating by reducing the output power or switching off in case of operation above the thermal limits of the luminaire or ballast. Depending on the luminaire design, the ITG operates at about 5 to 0 C above tc temperature. 6

7 Operating voltage Type Lamp type Wattage Uout TC-SEL x W 40 V TC-TEL HE x W 40 V PCA x/ TC BASIC Y II TC-DEL x W 40 V TC-TEL x W 40 V TC-TEL HE x4 W 40 V TC-TEL HE x7 W 40 V PCA x8 TC BASIC Y II TC-DEL x8 W 40 V TC-TEL x8 W 40 V TC-F x8 W 40 V TC-L x8 W 40 V PCA x8/4 TC ECO c Y II T5c x W 40 V TC-F x4 W 40 V TC-L x4 W 40 V TC-DEL x6 W 40 V TC-TEL x6 W 40 V TC-TEL x W 40 V PCA x6-57 TC BASIC Y II T5c x40 W 40 V TC-L x40 W 40 V TC-TEL x4 W 40 V TC-TEL x57 W 40 V PCA x8 TC-DD ECO Y II TC-DD x8 W 40 V PCA x55 T5c BASIC Y II T5c x55 W 40 V TC-SEL x W 40 V TC-TEL HE x W 40 V PCA x/ TC BASIC Y II TC-DEL x W 40 V TC-TEL x W 40 V TC-TEL HE x4 W 40 V TC-TEL HE x7 W 40 V PCA x8 TC BASIC Y II TC-DEL x8 W 40 V TC-TEL x8 W 40 V TC-F x8 W 40 V PCA x8/4 TC ECO c Y II TC-L x8 W 40 V TC-F x4 W 40 V TC-L x4 W 40 V TC-DEL x6 W 40 V PCA x6//4 TC BASIC Y II TC-TEL x6 W 40 V TC-TEL x W 40 V TC-TEL x4 W 40 V 7

8 Humidity: 5 % up to max. 85 %, not condensed (max. 56 days/year at 85 %) Storage temperature: -40 C up to max. +80 C The devices have to be within the specified temperature range (ta) before they can be operated. Installation instructions Wiring type and cross section The wiring can be in stranded wires with ferrules or solid with a cross section of mm². Strip 9.5 mm of insulation from the cables to ensure perfect operation of the push-wire terminals. wire preparation: mm² mm Mounting of device Max. torque for fixing: 0.5 Nm/M4 Expected life-time Type Lamp type Wattage ta = 40 C ta = 50 C ta = 60 C TC-SEL x W TC-TEL HE x W PCA x/ TC BASIC Y II TC-DEL x W TC-TEL x W TC-TEL HE x 4 W TC-TEL HE x 7 W PCA x8 TC BASIC Y II TC-DEL x 8 W TC-TEL x 8 W TC-F x 8 W TC-L x 8 W PCA x8/4 TCL BASIC c Y II T5c x W TC-F x 4 W TC-L x 4 W Release of the wiring Press down the push button and remove the cable from front. 8

9 Expected life-time Type Lamp type Wattage ta = 40 C ta = 50 C ta = 60 C TC-DEL x 6 W tc 55 C 65 C 75 C Life-time > 00,000 h > 00,000 h 80,000 h TC-TEL x 6 W tc 55 C 65 C 75 C Life-time > 00,000 h > 00,000 h 80,000 h TC-TEL x W tc 55 C 65 C 75 C Life-time > 00,000 h > 00,000 h 80,000 h PCA x6-57 TC BASIC Y II T5c x 40 W tc 50 C 60 C 75 C Life-time > 00,000 h > 00,000 h 75,000 h TC-L x 40 W tc 50 C 60 C 75 C Life-time > 00,000 h > 00,000 h 75,000 h TC-TEL x 4 W tc 50 C 60 C 75 C Life-time > 00,000 h > 00,000 h 75,000 h TC-TEL x 57 W PCA x8 TC-DD BASIC Y II TC-DD x 8 W PCA x55 T5c BASIC Y II T5c x 55 W tc 55 C 65 C x Life-time > 00,000 h > 00,000 h x TC-SEL x W TC-TEL HE x W PCA x/ TC BASIC Y II TC-DEL x W TC-TEL x W TC-TEL HE x 4 W TC-TEL HE x 7 W PCA x8 TC BASIC Y II TC-DEL x 8 W tc 55 C 60 C 70 C TC-TEL x 8 W tc 55 C 60 C 70 C TC-F x 8 W tc 60 C 65 C 75 C PCA x8/4 TCL BASIC c Y II TC-L x 8 W tc 60 C 65 C 75 C TC-F x 4 W tc 60 C 65 C 75 C TC-L x 4 W tc 60 C 65 C 75 C TC-DEL x 6 W tc 60 C 70 C 75 PCA x6//4 TC BASIC Y II TC-TEL x 6 W tc 60 C 70 C 75 TC-TEL x W tc 60 C 70 C 75 C TC-TEL x 4 W tc 60 C 65 C 75 C x = not permitted 9

10 Wiring advice The lead length is dependent on the capacitance of the cable. Ballast Terminal Maximum capacitance allowed Type Cold Hot Cold Hot PCA xx TC BASIC Y II, 0, 00 pf 00 pf PCA xx TC BASIC Y II,, 4, 5 0,, 6, 7 00 pf 00 pf With standard solid wire 0.5/0.75 mm² the capacitance of the lead is 0 80 pf/m. This value is influenced by the way the wiring is made. Lamp connection should be made with symmetrical wiring. Hot leads (0,, 6, 7) and cold leads (,, 4, 5) should be separated as much as possible. When using two or more dimmable ballasts in one luminaire with separate dimming controls, the lamp leads must be kept separate. Sensor wires Sensor wires must be routed separately from the lamp wires and mains cables otherwise the lighting control system may malfunction. If separate routing is not possible (for reasons of space) shielded lamp wires and mains cables must be used. Dimmable ballasts from Tridonic have to be earthed. * leads 0, keep wires short, max..0 m leads, max..0 m; ballast must be earthed * * digital signal DSI or switchdim PCA TC BASIC Y II x8 57 W D D * * control signal RFI Connection to the lamps of the hot leads must be kept as short as possible Mains leads should be kept apart from lamp leads (ideally 5 0 cm distance) Do not run mains leads adjacent to the electronic ballast Twist the lamp leads Keep the distance of lamp leads from the metal work as large as possible Mains wiring to be twisted when through wiring Keep the mains leads inside the luminaire as short as possible General advise Electronic ballasts are virtually noise free. Magnetic fields generated during the ignition cycle can cause some background noise but only for a few milliseconds For further technical information please visit D D * leads 0,, 6, 7 keep wires short, max..0 m leads,, 4, 5 max..0 m; ballast must be earthed * * digital signal DSI or switchdim PCA TC BASIC Y II x8 4 W Dimmable ballasts from Tridonic have to be earthed. Operation on DC voltage Our ballasts are construed to operate DC voltage and pulsed DC voltage. To operate ballasts with pulsed DC voltage the polarity is absolute mandatory. + D 5 D 6 * * control signal Isolation and electric strength testing of luminaires Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production. According to IEC Annex Q (informative only!) or ENEC 0-Annex A, each luminaire should be submitted to an isolation test with 500 V DC for second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal. The isolation resistance must be at least MΩ. As an alternative, IEC Annex Q describes a test of the electrical strength with 500 V AC (or.44 x 500 V DC). To avoid damage to the electronic devices this test must not be conducted. Glow-wire test according to EN C, 750 C and 850 C passed 0