Dimensional Analysis (Partial Analysis)

Size: px
Start display at page:

Download "Dimensional Analysis (Partial Analysis)"

Transcription

1 Dimensional Analysis (Partial Analysis) DA is a mathematical method of considerable value to problems in science and engineering especially physics and fluid mechanics. All physical quantities can usually be expressed in terms of certain primary quantities which in mechanics are: Length (L), Mass (M), and Time (T). e.g. Force = Mass x Acceleration = Mass x Length/Time = M L T -

2 The principle of homogeneity of dimensions can be used to:. Check whether an equation has been correctly formed (apples = apples) ;. Establish the form of an equation relating a number of variables (dimensional analysis); and 3. Assist in the analysis of experimental results (experimental design). Checking Equations: Eg. : Show by D. A. that the equation: p + ½ ρ v + ρ g z = H

3 is a possible relationship between pressure p, velocity v, and height z for a frictionless flow along a streamline of a fluid of density ρ, and determine the dimension of H. Solution: p = Force/Area = m a/area = M L T - L - = M L - T - ρ = mass/volume = M L -3 v = length/time = L T - g = L T -, Z = L p = M L- T- ½ ρ v = M L -3 x L T - = M L - T - ρ g z = M L -3 x L T - x L = M L - T - 3

4 All terms on the l.h.s have the same dimensions and the equation is physically possible if H also has dimension of M L - T -. ½ is a pure number hence not amenable to D. A. Constant could have been another number and the equation is still valid. Therefore, the analysis is not complete. We need additional information to confirm that the constant is indeed ½. Eg.. Check that Einstein s famous equation is indeed dimensionally correct: E = mc 4

5 Methods of dimensional analysis: grouping of variables. Many methods are available but we will consider the main ones:. Rayleigh indicial method. Buckingham π 3. Hunsaker and Rightmire (Whittington s) 4. Matrix Method The methods above are given roughly in chronological order. Also from most tedious to use to almost automatic (if matrix inversion routine available). 5

6 Rayleigh s method: Example: The velocity of propagation of a pressure wave through a liquid can be expected to depend on the elasticity of the liquid represented by the bulk modulus K, and its mass density ρ. Establish by D. A. the form of the possible relationship. Assume: u = C K a ρ b U = velocity = L T -, ρ = M L -3, K = M L - T - L T - = M a L -a T -a x M b L -3b M: 0 = a + b L: = -a 3b T: - = - a 6

7 Therefore: a = ½, b = -½, and a possible equation is: u = C K ρ Rayleigh s method is not always so straightforward. Consider the situation of flow over a U-notched weir. Q = f(ρ, µ, H, g) [Q] = [C ρ a µ b H c g d ] [ ] => dimensions of Using the M, L, T system, [L 3 T - ] = [ML -3 ] a [M L - T - ] b [L] c [L T - ] d M: 0 = a + b () L: 3 = -3a b +c + d () T: - = - b d (3) 7

8 8 We have only 3 equations, but there are 4 unknowns. Need to express a, b, c, in terms of d. b = d a = -b = d - c = 3 + 3a + b d = + 3d Q = C ρ (d-) µ (-d) H (+3d) g (d) d g H H C = 3 µ ρ ρ µ = 3 µ ρ φ µ ρ g H H Q dimensionless groups. Please check. This method can be very tedious if there are more variables.

9 Buckingham s π theorem This is the most well-known method and is the basis for the matrix and other methods. If there are n variables in a problem and these variables contain m primary dimensions (e.g. M, L, T), the equation relating the variables will contain n-m dimensionless groups. Buckingham referred to these dimensionless groups as π, π,, π n-m, and the final equation obtained is: π = φ (π, π 3,, π n-m ). 9

10 E.g. consider the previous problem with 5 variables, hence there will be 5 3 = dimensionless groups. The dimensionless groups can be formed as follows: ) Select 3 repeating variables from the list of variables which together must contain M, L,T. eg. ρ (ML 3 ), H (L), g (LT - ) ) Combine repeaters with one other variable in turn, 3) Never pick the dependent variable as a repeater. Consider: Q = f(ρ, µ, H, g) 5 variables Pick repeaters: ρ, H, g 0

11 Combine with one other variable, say, Q. x y z ρ H g π = Q ( 3 ) x ( ) ( ) ( 3 ) y z ML L LT L = T M: x = 0 L: -3x + y + z + 3 = 0 T: -z = 0 Therefore: z = -½, y = -5/ 0 π = ρ H π = g / Q H 5/ 5/ g / Q

12 π = ρ H g µ x y z ( 3 ) x y ( ) ( ) ( ) z ML L LT ML = T M: x + = 0 L: -3x + y + z - = 0 T: -z = 0 x = -, z = -/, y = 3/ π π = 3/ = ρ H g ρh µ 3/ g / / µ That is: g / Q H 5/ = φ ρh µ 3/ g /

13 Ex. The head loss per unit length ( h/l) of pipe in turbulent flow through a smooth pipe depends on v, D, ρ, g, and µ. Use Buckingham s π theorem to determine the general form of the equation. F( h/l, v, D, ρ, µ, g) = 0; 6 variables, 3 dimensions, 3 π terms. That is: π = φ(π, π 3 ). Choose 3 repeating variables: v, D, and ρ π = v ρ µ x D x x ( ) x x ( ) ( 3) x LT L ML ML = T 3

14 M: z + = 0 L: x + y 3z = 0 T: -x = 0 Therefore: x = -, z = -, and y = -. π = v D ρ µ or µ ρvd or ρvd µ = Re h L Final solution: = φ{ Re, Fr } Where Re = Reynold s number, and Fr = Froude number = v gd 4

15 Hunsaker and Rightmire s Method (947) This method is easier to use and quicker than Buckingham s method. The method is similar the Buckingham s method by use of repeating variables, but express them in term of the variables themselves. e.g. D to represent Length, [L] = D v to represent Time, [T] = L/v = D/v r to represent Mass, [M] = ρl 3 = ρd 3 π : g = L T - = v D D - = v D - v, therefore π = gd 5

16 π : µ = M L - T - = Therefore: π = ρvd µ ρd D = 3 v Re = ρvd h π 3 =, as before. L Example: A spherical drop of liquid of diameter D oscillates under the influence of its surface tension. Investigate the frequency of oscillation f. F(f,σ, D, ρ) = 0 Ans: f = K 3 σ ρd 6

17 Matrix Method Best for problems with many variables. Can be solved using a matrix inversion routine. Consider a problem with 7 variables in 4 dimensions (M, L, T, θ) First form the dimensional matrix: M L T θ a b c d e f g A B 7

18 We need to transform the above matrix to: a b c d e f g a b c d I = A - A D = A - B A - = adj A/ A Whatever operation was done to get the unit matrix on the left must be also done on the right to get D. 8

19 Eg. Consider the earlier problem of the head loss per unit length. F( h/l, v, g, D, ρ, µ) = 0 M ρ v D g µ h/l L T A B Inverse of A can be obtained using Minitab, Matlab, or by hand. 9

20 0 = A D = D = The three π terms are: L h vd v gd,, ρ µ The matrix method can obtain the π terms all in one go instead of one term at a time.

21 Comments about Dimensional Analysis Most important but most difficult problem in applying DA to any problem is the selection of the variables involved. There is no easy way of identifying the correct variables without specialized knowledge about the phenomenon being investigated. If you select too many variables, you get too many π terms and may require much additional experimentation to eliminate them. If important variables are omitted, then an incorrect result will be obtained, which may prove to be costly and difficult to ascertain.

22 Type of variables:. Geometry length, angles, diameter, or area.. Material properties ρ, µ, elasticity, etc. 3. External effects any variable that tends to produce a change in the system e.g. forces, pressures, velocities, gravity, etc. You need to keep the number of variables to a minimum, and that they are independent. E.g. D and Area need not be included together because one is derived from the other. Therefore, heavy thinking is required in variable selection similar to DOE.

23 Points to consider in the selection of variables:. Clearly define the problem. What is the main response variable of interest? That is, what is Y?. Consider the basic laws that govern the phenomenon. Even a crude theory may be useful. 3. Start the selection process by grouping the variables in the 3 broad classes: geometry, material properties, and external effects. 4. Consider other variables that may not fall into one of the three categories, e.g. time, temperature, colour, equipment, etc. 3

24 5. Be sure to include all quantities that enter the problem even though some of them may be held constant e.g. g. For D.A. it is the dimensions of the quantities that are important not specific values. 6. Make sure that all variables are independent look for relationships among subsets of the variables (same as DOE). Remember that after a dimensional analysis, you still need to carry out the experiment to relate the dimensionless groups. Hence DOE may be needed unless you have only or π terms. More on this later. 4

25 More on π terms Specific π terms obtained depend on the somewhat arbitrary selection of repeating variables. For example, if we choose: µ, D, g instead of ρ, D, v, we would end up with a different set of π terms. Both results would be correct, and both would lead to the same final equation for h/l, however, the function relating the different π terms would be different. 5

26 Hence, there is not a unique set of π terms which arises from a dimensional analysis. However the required number of π terms is fixed, and once a correct set is determined all other possible sets can be developed from this set by combination of products of the original set. e.g. if we have problem involving 3 π terms, π = φ(π, π 3 ) we can combine the π terms to give a new π term: ' a b π π 3 π = Then the relationship could be expressed as: ( ' π = φ π ) Or even: ( ' π = φ π ),π3,π3 6

27 All these would be correct; however, the required number of π terms cannot be reduced by this manipulation; only the form of the π terms is altered. e.g. π pd = ; π ρv = ρvd µ π = π π = pd ρv ρvd µ = pd µ v Which form of p terms is best? There is no simple answer. Best to keep it simple. Some p terms are well-known dimensionless numbers like Reynolds, Froude, Mach, Weber, Cauchy, Euler, etc. 7

28 Correlation of Experimental Data One of the most important uses of dimensional analysis is an aid in the efficient handling, interpretation, and correlation of experimental data. As noted earlier, DA cannot provide a complete answer and a specific relationship among the π terms cannot be determined without experimentation. The degree of difficulty obviously depends on the number of π terms. 8

29 Problems with: π term π = C where C = a constant π terms π = f(π ) simple regression problem > π terms π = f(π, π 3 ) multiple regression problem With more and more π terms, a DOE approach may be needed as in Problem 4 of assignment and may require the use of RSM if relationship is nonlinear. 9

30 Eg : The pressure drop per unit length, p/l for the flow of blood through a horizontal small diameter tube is a function of flow rate Q, diameter D, and the blood viscosity µ. For a series of test with D = mm and µ = Ns/m, the following data were obtained for p measured over a length of 300 mm. Q (m 3 /s) 3.6 x x x x x 0-6 p (N/m ). x x x x x 0 4 Perform a DA for this problem and make use of the data to determine a general relationship between p and Q, one that is valid for other values of D, L and µ. Solution: 4 variables, F ( p/l, D, Q, µ) = 0, i.e. 4 3 = π term 30

31 From D.A. (try this yourself), we get: ( p / L) D µ Q 4 = constant Substituting the values used in the experiment, ( p / L) D µ Q 4 = p / 0.3(0.00) Q 4 = p Q. Using the data obtained from the experiment, ( p / L) D µ Q 4 = [ 40.6, 40.7, ] p µ Q 40 L D Average for constant C = 40.5, hence: =.5 4 3

32 Eg : A liquid flows with a velocity v through a hole in the side of a tank. Assume that v = f(h, g, ρ, σ). Where h is the height of water above the hole, ρ is the density of the fluid, and σ the surface tension. The density ρ is 000 kg/m 3, and s = N/m. The data obtained by changing h and measuring v are: V (m/s) h (m) Plot the data using appropriate dimensional variables. Could any of the original variables have been omitted? Solution: 5 variables, F(v, h, g, ρ, σ) = 0, π terms. From dimensional analysis, v gh ρgh = φ σ 3

33 ρgh /σ 3.3 x x x x x 0 4 v/(gh) / Plotting the data will show that v gh means that ρ and σ can be omitted. is independent of ρ gh, which σ Of course this is well-known if one were to apply the Bernoulli equation to solve the problem. 33

34 References: Chapter, 3, 4 notes from course website. Thomas Szirtes (998): Applied Dimensional Analysis and Modeling, McGraw Hill, 790 pages. Most books in physics and fluid mechanics. 34

Flow past a circular cylinder with Re 2000: The pathlines of flow past any circular cylinder 1regardless of size, velocity, or fluid2 are as shown

Flow past a circular cylinder with Re 2000: The pathlines of flow past any circular cylinder 1regardless of size, velocity, or fluid2 are as shown 7708d_c07_384* 7/23/01 10:00 AM Page 384 Flow past a circular cylinder with Re 2000: The pathlines of flow past any circular cylinder 1regardless of size, velocity, or fluid2 are as shown provided that

More information

It is important to develop a meaningful and systematic way to perform an experiment.

It is important to develop a meaningful and systematic way to perform an experiment. Chapter 7: Dimensional Analysis, Modeling and Similitude. The solution to many engineering problems is achieved through the use of a combination of analysis and experimental data. One of the goals of an

More information

Dimensional and Model Analysis

Dimensional and Model Analysis Dimensional and Model Analysis 5.1 Fundamental dimensions 5.2 Rayleigh s and Buckingham s method 5.3 Dimension less numbers and their significance 5.4 Hydraulic similitude 5.5 Type of models 5.6 Distorted

More information

UNIT IV DIMENSIONAL AND MODEL ANALYSIS

UNIT IV DIMENSIONAL AND MODEL ANALYSIS UNIT IV DIMENSIONAL AND MODEL ANALYSIS INTRODUCTION Dimensional analysis is a method of dimensions. It is a mathematical technique used in research work for design and for conducting model tests. It deals

More information

Introduction to Fluid Flow

Introduction to Fluid Flow Introduction to Fluid Flow Learning Outcomes After this lecture you should be able to Explain viscosity and how it changes with temperature Write the continuity equation Define laminar and turbulent flow

More information

UNIT V : DIMENSIONAL ANALYSIS AND MODEL STUDIES

UNIT V : DIMENSIONAL ANALYSIS AND MODEL STUDIES UNIT V : DIMENSIONAL ANALYSIS AND MODEL STUDIES 1. Define dimensional analysis. Dimensional analysis is a mathematical technique which makes use of the study of dimensions as an aid to solution of several

More information

UNIT -5. Dimensional Analysis. Model Analysis. Fundamental Dimensions Dimensional Homogeneity Method of analysis

UNIT -5. Dimensional Analysis. Model Analysis. Fundamental Dimensions Dimensional Homogeneity Method of analysis UNIT -5 Dimensional Analysis Fundamental Dimensions Dimensional Homogeneity Method of analysis Rayleigh Method Buckingham pi theorem Method Model Analysis Dimensionless parameters Similitude and model

More information

Go back to the main index page

Go back to the main index page 1 of 10 8/24/2006 11:22 AM Go back to the main index page 1. In engineering the application of fluid mechanics in designs make much of the use of empirical results from a lot of experiments. This data

More information

BUCKINGHAM PI THEOREM

BUCKINGHAM PI THEOREM BUCKINGHAM PI THEOREM Dimensional Analysis It is used to determine the equation is right or wrong. The calculation is depends on the unit or dimensional conditions of the equations. For example; F=ma F=MLT

More information

It is important to develop a meaningful and systematic way to perform an experiment.

It is important to develop a meaningful and systematic way to perform an experiment. Chapter 7: Dimensional Analysis, Modeling and Similitude. The solution to many engineering problems is achieved through the use of a combination of analysis and experimental data. One of the goals of an

More information

Chapter 7 DIMENSIONAL ANALYSIS AND SIMILITUDE Because so few real flows can be solved exactly by analytical methods alone, the development of fluid

Chapter 7 DIMENSIONAL ANALYSIS AND SIMILITUDE Because so few real flows can be solved exactly by analytical methods alone, the development of fluid Chapter 7 DIMENSIONAL ANALYSIS AND SIMILITUDE Because so few real flows can be solved exactly by analytical methods alone, the development of fluid mechanics has depended heavily on experimental results.

More information

Chapter 7: Dimensional Analysis

Chapter 7: Dimensional Analysis 7-1 Dimension and Units 7-2 Dimensional Homogeneity 7-3 Dimensional Analysis and Similarity 7-4 Methods of Repeating Variables 7-5 Experimental Testing and Incomplete Similarity 7-1 Dimensions and Units

More information

S.E. (Mech.) (First Sem.) EXAMINATION, (Common to Mech/Sandwich) FLUID MECHANICS (2008 PATTERN) Time : Three Hours Maximum Marks : 100

S.E. (Mech.) (First Sem.) EXAMINATION, (Common to Mech/Sandwich) FLUID MECHANICS (2008 PATTERN) Time : Three Hours Maximum Marks : 100 Total No. of Questions 12] [Total No. of Printed Pages 8 Seat No. [4262]-113 S.E. (Mech.) (First Sem.) EXAMINATION, 2012 (Common to Mech/Sandwich) FLUID MECHANICS (2008 PATTERN) Time : Three Hours Maximum

More information

Reduction of Variables Dimensional Analysis

Reduction of Variables Dimensional Analysis Reduction of Variables Dimensional Analysis Dimensions and Units Review Dimension: Measure of a physical quantity, e.g., length, time, mass Units: Assignment of a number to a dimension, e.g., (m), (sec),

More information

V. MODELING, SIMILARITY, AND DIMENSIONAL ANALYSIS To this point, we have concentrated on analytical methods of solution for fluids problems.

V. MODELING, SIMILARITY, AND DIMENSIONAL ANALYSIS To this point, we have concentrated on analytical methods of solution for fluids problems. V. MODELING, SIMILARITY, AND DIMENSIONAL ANALYSIS To this point, we have concentrated on analytical methods of solution for fluids problems. However, analytical methods are not always satisfactory due

More information

CEE 3310 Dimensional Analysis & Similitude, Oct. 22,

CEE 3310 Dimensional Analysis & Similitude, Oct. 22, CEE 3310 Dimensional Analysis & Similitude, Oct., 018 115 5.5 Review vorticity twice the local rotation rate: ω x = w y v z, ω y = u z w x, ω z = v x u y Dimensional Analysis Buckingham Pi Theorem: k =

More information

Prof. Scalo Prof. Vlachos Prof. Ardekani Prof. Dabiri 08:30 09:20 A.M 10:30 11:20 A.M. 1:30 2:20 P.M. 3:30 4:20 P.M.

Prof. Scalo Prof. Vlachos Prof. Ardekani Prof. Dabiri 08:30 09:20 A.M 10:30 11:20 A.M. 1:30 2:20 P.M. 3:30 4:20 P.M. Page 1 Neatly print your name: Signature: (Note that unsigned exams will be given a score of zero.) Circle your lecture section (-1 point if not circled, or circled incorrectly): Prof. Scalo Prof. Vlachos

More information

Chapter 2 Similitude Theory and Applications

Chapter 2 Similitude Theory and Applications Chapter 2 Similitude Theory and Applications Wikipedia definition of similitude is a concept that is used in the testing of engineering models. A model is said to have similitude with the real application

More information

1.The pressure drop per unit length that develops due to friction cannot generally be solved analytically. A. True B. False

1.The pressure drop per unit length that develops due to friction cannot generally be solved analytically. A. True B. False CHAPTER 07 1.The pressure drop per unit length that develops due to friction cannot generally be solved analytically. 2.A qualitative description of physical quantities can be given in terms of. YOUR ANSWER:

More information

MECHANICAL PROPERTIES OF FLUIDS

MECHANICAL PROPERTIES OF FLUIDS CHAPTER-10 MECHANICAL PROPERTIES OF FLUIDS QUESTIONS 1 marks questions 1. What are fluids? 2. How are fluids different from solids? 3. Define thrust of a liquid. 4. Define liquid pressure. 5. Is pressure

More information

Middle East Technical University Department of Mechanical Engineering ME 305 Fluid Mechanics I Fall 2018 Section 4 (Dr.

Middle East Technical University Department of Mechanical Engineering ME 305 Fluid Mechanics I Fall 2018 Section 4 (Dr. Middle East Technical University Department of Mechanical Engineering ME 305 Fluid Mechanics I Fall 2018 Section 4 (Dr. Sert) Study Set 7 Reading Assignment R1. Read the section Common Dimensionless Groups

More information

Hydromechanics: Course Summary

Hydromechanics: Course Summary Hydromechanics: Course Summary Hydromechanics VVR090 Material Included; French: Chapters to 9 and 4 + Sample problems Vennard & Street: Chapters 8 + 3, and (part of it) Roberson & Crowe: Chapter Collection

More information

Physics 3 Summer 1990 Lab 7 - Hydrodynamics

Physics 3 Summer 1990 Lab 7 - Hydrodynamics Physics 3 Summer 1990 Lab 7 - Hydrodynamics Theory Consider an ideal liquid, one which is incompressible and which has no internal friction, flowing through pipe of varying cross section as shown in figure

More information

LECTURE 1 THE CONTENTS OF THIS LECTURE ARE AS FOLLOWS:

LECTURE 1 THE CONTENTS OF THIS LECTURE ARE AS FOLLOWS: LECTURE 1 THE CONTENTS OF THIS LECTURE ARE AS FOLLOWS: 1.0 INTRODUCTION TO FLUID AND BASIC EQUATIONS 2.0 REYNOLDS NUMBER AND CRITICAL VELOCITY 3.0 APPROACH TOWARDS REYNOLDS NUMBER REFERENCES Page 1 of

More information

ME 3560 Fluid Mechanics

ME 3560 Fluid Mechanics ME 3560 Fluid Mechanics 1 7.1 Dimensional Analysis Many problems of interest in fluid mechanics cannot be solved using the integral and/or differential equations. Examples of problems that are studied

More information

Scaling and Dimensional Analysis

Scaling and Dimensional Analysis Scaling and Dimensional Analysis Understanding the role of dimensions and the use of dimensionless numbers for evaluating the forces in a system so that the correct assumptions about it can be made and

More information

Part A: 1 pts each, 10 pts total, no partial credit.

Part A: 1 pts each, 10 pts total, no partial credit. Part A: 1 pts each, 10 pts total, no partial credit. 1) (Correct: 1 pt/ Wrong: -3 pts). The sum of static, dynamic, and hydrostatic pressures is constant when flow is steady, irrotational, incompressible,

More information

Similitude and Dimensional Analysis. CE Fluid Mechanics Diogo Bolster

Similitude and Dimensional Analysis. CE Fluid Mechanics Diogo Bolster Similitude and Dimensional Analysis CE30460 - Fluid Mechanics Diogo Bolster Goals of Chapter Apply Pi Theorem Develop dimensionless variables for a given flow situation Use dimensional variables in data

More information

Please remember all the unit that you use in your calculation. There are no marks for correct answer without unit.

Please remember all the unit that you use in your calculation. There are no marks for correct answer without unit. CHAPTER 1 : PROPERTIES OF FLUIDS What is fluid? A fluid is defined as a substance that deforms continuously when acted on by a shearing stress at any magnitude. In a fluid at rest, normal stress is called

More information

5 SIMILITUDE. 5.1 Use of Nondimensional Groups

5 SIMILITUDE. 5.1 Use of Nondimensional Groups 5 SIMIITDE 5. se of Nondimensional Groups For a consistent description of physical processes, we require that all terms in an equation must have the same units. On the basis of physical laws, some quantities

More information

PIPE FLOW. General Characteristic of Pipe Flow. Some of the basic components of a typical pipe system are shown in Figure 1.

PIPE FLOW. General Characteristic of Pipe Flow. Some of the basic components of a typical pipe system are shown in Figure 1. PIPE FLOW General Characteristic of Pipe Flow Figure 1 Some of the basic components of a typical pipe system are shown in Figure 1. They include the pipes, the various fitting used to connect the individual

More information

Dimensional Reasoning- Lecture Notes

Dimensional Reasoning- Lecture Notes Measurements consist of two properties: 1) A quality or dimension, and 2) A quantity expressed in terms of units Dimensions Dimensional Reasoning- Lecture Notes A. Everything that can be measured consists

More information

Physics 123 Unit #1 Review

Physics 123 Unit #1 Review Physics 123 Unit #1 Review I. Definitions & Facts Density Specific gravity (= material / water) Pressure Atmosphere, bar, Pascal Barometer Streamline, laminar flow Turbulence Gauge pressure II. Mathematics

More information

Fundamentals of Fluid Mechanics

Fundamentals of Fluid Mechanics Sixth Edition Fundamentals of Fluid Mechanics International Student Version BRUCE R. MUNSON DONALD F. YOUNG Department of Aerospace Engineering and Engineering Mechanics THEODORE H. OKIISHI Department

More information

Study fluid dynamics. Understanding Bernoulli s Equation.

Study fluid dynamics. Understanding Bernoulli s Equation. Chapter Objectives Study fluid dynamics. Understanding Bernoulli s Equation. Chapter Outline 1. Fluid Flow. Bernoulli s Equation 3. Viscosity and Turbulence 1. Fluid Flow An ideal fluid is a fluid that

More information

NPTEL Quiz Hydraulics

NPTEL Quiz Hydraulics Introduction NPTEL Quiz Hydraulics 1. An ideal fluid is a. One which obeys Newton s law of viscosity b. Frictionless and incompressible c. Very viscous d. Frictionless and compressible 2. The unit of kinematic

More information

Lesson 6 Review of fundamentals: Fluid flow

Lesson 6 Review of fundamentals: Fluid flow Lesson 6 Review of fundamentals: Fluid flow The specific objective of this lesson is to conduct a brief review of the fundamentals of fluid flow and present: A general equation for conservation of mass

More information

Fluid Mechanics. du dy

Fluid Mechanics. du dy FLUID MECHANICS Technical English - I 1 th week Fluid Mechanics FLUID STATICS FLUID DYNAMICS Fluid Statics or Hydrostatics is the study of fluids at rest. The main equation required for this is Newton's

More information

ː ˠ Ǫː Ǫ. ʿǪ ǪȅԹ ˠ. Save from:

ː ˠ Ǫː Ǫ. ʿǪ ǪȅԹ ˠ. Save from: ː ˠ Ǫː Ǫ قسم الهندسة الكيمیاویة Ǫ ߧ Ǫلثانیة ʿǪ ǪȅԹ ˠ د. ˡ Զ ބ, د.صلاح سلمان Save from: http://www.uotechnology.edu.iq/dep-chem-eng/index.htm FLUID FLOW- 2 nd Year CHEMICAL ENG. DEPT. LECTURE-TWO-

More information

Fluid Mechanics III. 1. Dimensional analysis and similarity

Fluid Mechanics III. 1. Dimensional analysis and similarity Fluid Mechanics III 1. Dimensional analysis and similarity Similarity The real world is non-dimensional. The proposition the Eiffel Tower is tall has no sense unless we state what is the object we compare

More information

HOW TO GET A GOOD GRADE ON THE MME 2273B FLUID MECHANICS 1 EXAM. Common mistakes made on the final exam and how to avoid them

HOW TO GET A GOOD GRADE ON THE MME 2273B FLUID MECHANICS 1 EXAM. Common mistakes made on the final exam and how to avoid them HOW TO GET A GOOD GRADE ON THE MME 2273B FLUID MECHANICS 1 EXAM Common mistakes made on the final exam and how to avoid them HOW TO GET A GOOD GRADE ON THE MME 2273B EXAM Introduction You now have a lot

More information

Dimensions represent classes of units we use to describe a physical quantity. Most fluid problems involve four primary dimensions

Dimensions represent classes of units we use to describe a physical quantity. Most fluid problems involve four primary dimensions BEE 5330 Fluids FE Review, Feb 24, 2010 1 A fluid is a substance that can not support a shear stress. Liquids differ from gasses in that liquids that do not completely fill a container will form a free

More information

TURBOMACHINES. VIJAYAVITHAL BONGALE Associate Professor and Head Department of Mechanical Engineering Malnad College of Engineering, Hassan

TURBOMACHINES. VIJAYAVITHAL BONGALE Associate Professor and Head Department of Mechanical Engineering Malnad College of Engineering, Hassan TURBOMACHINES VIJAYAVITHAL BONGALE Associate Professor and Head Department of Mechanical Engineering Malnad College of Engineering, Hassan 573 201. Mobile No:9448821954 E-mail : vvb@mcehassan.ac.in 1 Dimensional

More information

DIMENSIONAL ANALYSIS IN MOMENTUM TRANSFER

DIMENSIONAL ANALYSIS IN MOMENTUM TRANSFER DIMENSIONAL ANALYSIS IN MOMENTUM TRANSFER FT I Alda Simões Techniques for Dimensional Analysis Fluid Dynamics: Microscopic analysis, theory Physical modelling Differential balances Limited to simple geometries

More information

Mass of fluid leaving per unit time

Mass of fluid leaving per unit time 5 ENERGY EQUATION OF FLUID MOTION 5.1 Eulerian Approach & Control Volume In order to develop the equations that describe a flow, it is assumed that fluids are subject to certain fundamental laws of physics.

More information

MECHANICAL PROPERTIES OF FLUIDS:

MECHANICAL PROPERTIES OF FLUIDS: Important Definitions: MECHANICAL PROPERTIES OF FLUIDS: Fluid: A substance that can flow is called Fluid Both liquids and gases are fluids Pressure: The normal force acting per unit area of a surface is

More information

BUCKINGHAM PI THEOREM

BUCKINGHAM PI THEOREM BUCKINGHAM PI THEOREM Dimensional Analysis It is used to determine the equation is right or wrong. The calculation is depends on the unit or dimensional conditions of the equations. For example; F=ma F=MLT

More information

Summary PHY101 ( 2 ) T / Hanadi Al Harbi

Summary PHY101 ( 2 ) T / Hanadi Al Harbi الكمية Physical Quantity القانون Low التعريف Definition الوحدة SI Unit Linear Momentum P = mθ be equal to the mass of an object times its velocity. Kg. m/s vector quantity Stress F \ A the external force

More information

Fluids. Fluids in Motion or Fluid Dynamics

Fluids. Fluids in Motion or Fluid Dynamics Fluids Fluids in Motion or Fluid Dynamics Resources: Serway - Chapter 9: 9.7-9.8 Physics B Lesson 3: Fluid Flow Continuity Physics B Lesson 4: Bernoulli's Equation MIT - 8: Hydrostatics, Archimedes' Principle,

More information

Convective Mass Transfer

Convective Mass Transfer Convective Mass Transfer Definition of convective mass transfer: The transport of material between a boundary surface and a moving fluid or between two immiscible moving fluids separated by a mobile interface

More information

Introduction to Marine Hydrodynamics

Introduction to Marine Hydrodynamics 1896 190 1987 006 Introduction to Marine Hydrodynamics (NA35) Department of Naval Architecture and Ocean Engineering School of Naval Architecture, Ocean & ivil Engineering Shanghai Jiao Tong University

More information

In steady flow the velocity of the fluid particles at any point is constant as time passes.

In steady flow the velocity of the fluid particles at any point is constant as time passes. Chapter 10 Fluids Fluids in Motion In steady flow the velocity of the fluid particles at any point is constant as time passes. Unsteady flow exists whenever the velocity of the fluid particles at a point

More information

UNIT III DIMENSIONAL ANALYSIS

UNIT III DIMENSIONAL ANALYSIS UNIT III DIMENSIONAL ANALYSIS INTRODUCTION Dimensional analysis is one of the most important mathematical tools in the study of fluid mechanics. It is a mathematical technique, which makes use of the study

More information

Signature: (Note that unsigned exams will be given a score of zero.)

Signature: (Note that unsigned exams will be given a score of zero.) Neatly print your name: Signature: (Note that unsigned exams will be given a score of zero.) Circle your lecture section (-1 point if not circled, or circled incorrectly): Prof. Dabiri Prof. Wassgren Prof.

More information

EXPERIMENT NO: F5. Losses in Piping Systems

EXPERIMENT NO: F5. Losses in Piping Systems SJSU ME115 - THERMAL ENGINEERING LAB EXPERIMENT NO: F5 Losses in Piping Systems Objective One of the most common problems in fluid mechanics is the estimation of pressure loss. It is the objective of this

More information

FACULTY OF CHEMICAL & ENERGY ENGINEERING FLUID MECHANICS LABORATORY TITLE OF EXPERIMENT: MINOR LOSSES IN PIPE (E4)

FACULTY OF CHEMICAL & ENERGY ENGINEERING FLUID MECHANICS LABORATORY TITLE OF EXPERIMENT: MINOR LOSSES IN PIPE (E4) FACULTY OF CHEMICAL & ENERGY ENGINEERING FLUID MECHANICS LABORATORY TITLE OF EXPERIMENT: MINOR LOSSES IN PIPE (E4) 1 1.0 Objectives The objective of this experiment is to calculate loss coefficient (K

More information

BERNOULLI EQUATION. The motion of a fluid is usually extremely complex.

BERNOULLI EQUATION. The motion of a fluid is usually extremely complex. BERNOULLI EQUATION The motion of a fluid is usually extremely complex. The study of a fluid at rest, or in relative equilibrium, was simplified by the absence of shear stress, but when a fluid flows over

More information

Stream Tube. When density do not depend explicitly on time then from continuity equation, we have V 2 V 1. δa 2. δa 1 PH6L24 1

Stream Tube. When density do not depend explicitly on time then from continuity equation, we have V 2 V 1. δa 2. δa 1 PH6L24 1 Stream Tube A region of the moving fluid bounded on the all sides by streamlines is called a tube of flow or stream tube. As streamline does not intersect each other, no fluid enters or leaves across the

More information

Chapter 9: Solids and Fluids

Chapter 9: Solids and Fluids Chapter 9: Solids and Fluids State of matters: Solid, Liquid, Gas and Plasma. Solids Has definite volume and shape Can be crystalline or amorphous Molecules are held in specific locations by electrical

More information

Learning Objectives. Lesson 6: Mathematical Models of Fluid Flow Components. ET 438a Automatic Control Systems Technology 8/27/2015

Learning Objectives. Lesson 6: Mathematical Models of Fluid Flow Components. ET 438a Automatic Control Systems Technology 8/27/2015 Lesson 6: Mathematical Models of Fluid Flow Components ET 438a Automatic Control Systems Technology lesson6et438a.pptx 1 Learning Objectives After this presentation you will be able to: Define the characteristics

More information

PHYSICS 126 Fall 2010 Midterm 1

PHYSICS 126 Fall 2010 Midterm 1 PHYSICS 16 Fall 010 Midterm 1 Name: SOLUTIONS Student ID: Section Number: Closed book with one sheet of notes and a calculator. Answer the questions in spaces provided on each sheet. If you run out of

More information

DIMENSIONAL REASONING

DIMENSIONAL REASONING Measurements consist of two properties: ) a quality or dimension, and ) a quantity expressed in terms of "units" Dimensions DIMENSIONAL REASONING A. Everything that can be measured consists of a combination

More information

Pressure in a fluid P P P P

Pressure in a fluid P P P P Fluids Gases (compressible) and liquids (incompressible) density of gases can change dramatically, while that of liquids much less so Gels, colloids, liquid crystals are all odd-ball states of matter We

More information

PROPERTIES OF FLUIDS

PROPERTIES OF FLUIDS Unit - I Chapter - PROPERTIES OF FLUIDS Solutions of Examples for Practice Example.9 : Given data : u = y y, = 8 Poise = 0.8 Pa-s To find : Shear stress. Step - : Calculate the shear stress at various

More information

CHEN 3200 Fluid Mechanics Spring Homework 3 solutions

CHEN 3200 Fluid Mechanics Spring Homework 3 solutions Homework 3 solutions 1. An artery with an inner diameter of 15 mm contains blood flowing at a rate of 5000 ml/min. Further along the artery, arterial plaque has partially clogged the artery, reducing the

More information

Fluid Mechanics. Jim Emery 9/3/ Bernoulli s Law 2. 2 Torricelli s Law 3. 3 Time to Empty a Tank 3. 4 Viscosity 4. 5 The Acceleration 5

Fluid Mechanics. Jim Emery 9/3/ Bernoulli s Law 2. 2 Torricelli s Law 3. 3 Time to Empty a Tank 3. 4 Viscosity 4. 5 The Acceleration 5 Fluid Mechanics Jim Emery 9/3/2010 Contents 1 Bernoulli s Law 2 2 Torricelli s Law 3 3 Time to Empty a Tank 3 4 Viscosity 4 5 The Acceleration 5 6 The Equation of Motion Due to Cauchy 7 7 The Deformation

More information

ρ mixture = m mixture /V = (SG antifreeze ρ water V antifreeze + SG water ρ water V water )/V, so we get

ρ mixture = m mixture /V = (SG antifreeze ρ water V antifreeze + SG water ρ water V water )/V, so we get CHAPTER 10 1. When we use the density of granite, we have m = ρv = (.7 10 3 kg/m 3 )(1 10 8 m 3 ) =.7 10 11 kg.. When we use the density of air, we have m = ρv = ρlwh = (1.9 kg/m 3 )(5.8 m)(3.8 m)(.8 m)

More information

In this process the temperature difference across the given length of pipe can be described as:

In this process the temperature difference across the given length of pipe can be described as: Dimensional Analysis/Model Testing You are tasked with designing a heat exchanger around a section of piping in a synthesis plant in which temperature control will be critical to prevent bi-product formation.

More information

FE Fluids Review March 23, 2012 Steve Burian (Civil & Environmental Engineering)

FE Fluids Review March 23, 2012 Steve Burian (Civil & Environmental Engineering) Topic: Fluid Properties 1. If 6 m 3 of oil weighs 47 kn, calculate its specific weight, density, and specific gravity. 2. 10.0 L of an incompressible liquid exert a force of 20 N at the earth s surface.

More information

Lecture 30 (Walker: ) Fluid Dynamics April 15, 2009

Lecture 30 (Walker: ) Fluid Dynamics April 15, 2009 Physics 111 Lecture 30 (Walker: 15.6-7) Fluid Dynamics April 15, 2009 Midterm #2 - Monday April 20 Chap. 7,Chap. 8 (not 8.5) Chap. 9 (not 9.6, 9.8) Chap. 10, Chap. 11 (not 11.8-9) Chap. 13 (not 13.6-8)

More information

ENGINEERING FLUID MECHANICS. CHAPTER 1 Properties of Fluids

ENGINEERING FLUID MECHANICS. CHAPTER 1 Properties of Fluids CHAPTER 1 Properties of Fluids ENGINEERING FLUID MECHANICS 1.1 Introduction 1.2 Development of Fluid Mechanics 1.3 Units of Measurement (SI units) 1.4 Mass, Density, Specific Weight, Specific Volume, Specific

More information

FLUID MECHANICS D203 SAE SOLUTIONS TUTORIAL 2 APPLICATIONS OF BERNOULLI SELF ASSESSMENT EXERCISE 1

FLUID MECHANICS D203 SAE SOLUTIONS TUTORIAL 2 APPLICATIONS OF BERNOULLI SELF ASSESSMENT EXERCISE 1 FLUID MECHANICS D203 SAE SOLUTIONS TUTORIAL 2 APPLICATIONS OF BERNOULLI SELF ASSESSMENT EXERCISE 1 1. A pipe 100 mm bore diameter carries oil of density 900 kg/m3 at a rate of 4 kg/s. The pipe reduces

More information

FLOW IN PIPES. Mark J McCready University of Notre Dame July 24, chemeprof.com

FLOW IN PIPES. Mark J McCready University of Notre Dame July 24, chemeprof.com FLOW IN PIPES Mark J McCready University of Notre Dame July 24, 2017 OVERVIEW This lecture will provide the simplest framework to explain The three forces at that are important to fluid flow in pipes The

More information

Chapter 15B - Fluids in Motion. A PowerPoint Presentation by Paul E. Tippens, Professor of Physics Southern Polytechnic State University

Chapter 15B - Fluids in Motion. A PowerPoint Presentation by Paul E. Tippens, Professor of Physics Southern Polytechnic State University Chapter 15B - Fluids in Motion A PowerPoint Presentation by Paul E. Tippens, Professor of Physics Southern Polytechnic State University 007 Paul E. Tippens Fluid Motion The lower falls at Yellowstone National

More information

Fluid Mechanics Answer Key of Objective & Conventional Questions

Fluid Mechanics Answer Key of Objective & Conventional Questions 019 MPROVEMENT Mechanical Engineering Fluid Mechanics Answer Key of Objective & Conventional Questions 1 Fluid Properties 1. (c). (b) 3. (c) 4. (576) 5. (3.61)(3.50 to 3.75) 6. (0.058)(0.05 to 0.06) 7.

More information

Liquids CHAPTER 13 FLUIDS FLUIDS. Gases. Density! Bulk modulus! Compressibility. To begin with... some important definitions...

Liquids CHAPTER 13 FLUIDS FLUIDS. Gases. Density! Bulk modulus! Compressibility. To begin with... some important definitions... CHAPTER 13 FLUIDS FLUIDS Liquids Gases Density! Bulk modulus! Compressibility Pressure in a fluid! Hydraulic lift! Hydrostatic paradox Measurement of pressure! Manometers and barometers Buoyancy and Archimedes

More information

FLUID MECHANICS PROF. DR. METİN GÜNER COMPILER

FLUID MECHANICS PROF. DR. METİN GÜNER COMPILER FLUID MECHANICS PROF. DR. METİN GÜNER COMPILER ANKARA UNIVERSITY FACULTY OF AGRICULTURE DEPARTMENT OF AGRICULTURAL MACHINERY AND TECHNOLOGIES ENGINEERING 1 5. FLOW IN PIPES Liquid or gas flow through pipes

More information

Visualization of flow pattern over or around immersed objects in open channel flow.

Visualization of flow pattern over or around immersed objects in open channel flow. EXPERIMENT SEVEN: FLOW VISUALIZATION AND ANALYSIS I OBJECTIVE OF THE EXPERIMENT: Visualization of flow pattern over or around immersed objects in open channel flow. II THEORY AND EQUATION: Open channel:

More information

CHAPTER 9 DIMENSIONAL ANALYSIS AND SCALING

CHAPTER 9 DIMENSIONAL ANALYSIS AND SCALING CHAPTER 9 DIMENSIONAL ANALYSIS AND SCALING The Philosopher s approach The Mathematicians s approach The Engineer s approach Example - an orifice plate Example - an aeroplane Example - the drag force on

More information

ENG3103 Engineering Problem Solving Computations Semester 2, 2013

ENG3103 Engineering Problem Solving Computations Semester 2, 2013 Assessment: Assignment 2 Due: 16 September 2013 Marks: 100 Value: 10 % Question 1 (70 marks) Introduction You are designing a pipe network system that transfers water from the upper pipe to the lower pipe.

More information

FLOW MEASUREMENT IN PIPES EXPERIMENT

FLOW MEASUREMENT IN PIPES EXPERIMENT University of Leicester Engineering Department FLOW MEASUREMENT IN PIPES EXPERIMENT Page 1 FORMAL LABORATORY REPORT Name of the experiment: FLOW MEASUREMENT IN PIPES Author: Apollin nana chaazou Partner

More information

Chapter 11 - Fluids in Motion. Sections 7-9

Chapter 11 - Fluids in Motion. Sections 7-9 Chapter - Fluids in Motion Sections 7-9 Fluid Motion The lower falls at Yellowstone National Park: the water at the top of the falls passes through a narrow slot, causing the velocity to increase at that

More information

Chapter 10 - Mechanical Properties of Fluids. The blood pressure in humans is greater at the feet than at the brain

Chapter 10 - Mechanical Properties of Fluids. The blood pressure in humans is greater at the feet than at the brain Question 10.1: Explain why The blood pressure in humans is greater at the feet than at the brain Atmospheric pressure at a height of about 6 km decreases to nearly half of its value at the sea level, though

More information

cos(θ)sin(θ) Alternative Exercise Correct Correct θ = 0 skiladæmi 10 Part A Part B Part C Due: 11:59pm on Wednesday, November 11, 2015

cos(θ)sin(θ) Alternative Exercise Correct Correct θ = 0 skiladæmi 10 Part A Part B Part C Due: 11:59pm on Wednesday, November 11, 2015 skiladæmi 10 Due: 11:59pm on Wednesday, November 11, 015 You will receive no credit for items you complete after the assignment is due Grading Policy Alternative Exercise 1115 A bar with cross sectional

More information

Dimensional Analysis

Dimensional Analysis Mathematical Modeling Lia Vas Dimensional Analysis One of the key steps in the process of mathematical modeling is to determine the relationship between the variables. Considering the dimensions of those

More information

LECTURE 4 FLUID FLOW & SURFACE TENSION. Lecture Instructor: Kazumi Tolich

LECTURE 4 FLUID FLOW & SURFACE TENSION. Lecture Instructor: Kazumi Tolich LECTURE 4 FLUID FLOW & SURFACE TENSION Lecture Instructor: Kazumi Tolich Lecture 4 2 Reading chapter 15.6 to 15.9 Continuity equation Bernoulli s equation n Torricelli s law Viscosity Surface tension Equation

More information

Physics 201 Chapter 13 Lecture 1

Physics 201 Chapter 13 Lecture 1 Physics 201 Chapter 13 Lecture 1 Fluid Statics Pascal s Principle Archimedes Principle (Buoyancy) Fluid Dynamics Continuity Equation Bernoulli Equation 11/30/2009 Physics 201, UW-Madison 1 Fluids Density

More information

ACCOUNTING FOR FRICTION IN THE BERNOULLI EQUATION FOR FLOW THROUGH PIPES

ACCOUNTING FOR FRICTION IN THE BERNOULLI EQUATION FOR FLOW THROUGH PIPES ACCOUNTING FOR FRICTION IN THE BERNOULLI EQUATION FOR FLOW THROUGH PIPES Some background information first: We have seen that a major limitation of the Bernoulli equation is that it does not account for

More information

f= flow rate (m 3 /s) A = cross-sectional area of the pipe (m 2 ) v= flow speed (m/s)

f= flow rate (m 3 /s) A = cross-sectional area of the pipe (m 2 ) v= flow speed (m/s) Fluid Mechanics Flow Rate and Continuity Equation If you have a pipe that is flowing a liquid you will have a flow rate. The flow rate is the volume of fluid that passes any particular point per unit of

More information

ACE Engineering College

ACE Engineering College ACE Engineering College Ankushapur (V), Ghatkesar (M), R.R.Dist 501 301. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * MECHANICS OF FLUIDS & HYDRAULIC

More information

Chapter 6. Losses due to Fluid Friction

Chapter 6. Losses due to Fluid Friction Chapter 6 Losses due to Fluid Friction 1 Objectives To measure the pressure drop in the straight section of smooth, rough, and packed pipes as a function of flow rate. To correlate this in terms of the

More information

Chapter 9 Solids and Fluids. Elasticity Archimedes Principle Bernoulli s Equation

Chapter 9 Solids and Fluids. Elasticity Archimedes Principle Bernoulli s Equation Chapter 9 Solids and Fluids Elasticity Archimedes Principle Bernoulli s Equation States of Matter Solid Liquid Gas Plasmas Solids: Stress and Strain Stress = Measure of force felt by material Stress= Force

More information

ME 431A/538A/538B Homework 22 October 2018 Advanced Fluid Mechanics

ME 431A/538A/538B Homework 22 October 2018 Advanced Fluid Mechanics ME 431A/538A/538B Homework 22 October 2018 Advanced Fluid Mechanics For Friday, October 26 th Start reading the handout entitled Notes on finite-volume methods. Review Chapter 7 on Dimensional Analysis

More information

Figure 1 Answer: = m

Figure 1 Answer: = m Q1. Figure 1 shows a solid cylindrical steel rod of length =.0 m and diameter D =.0 cm. What will be increase in its length when m = 80 kg block is attached to its bottom end? (Young's modulus of steel

More information

Answers to test yourself questions

Answers to test yourself questions Answers to test yourself questions Option B B Rotational dynamics ( ω + ω )t Use 0 ( +.).0 θ to get θ 46. 46 rad. Use ω ω0 + αθ to get ω.0 +. 4 and so ω 7.8 7 rad s. Use ω ω0 + αθ to get.4. + α 0 π. Hence

More information

Introduction to Fluid Mechanics

Introduction to Fluid Mechanics Introduction to Fluid Mechanics Tien-Tsan Shieh April 16, 2009 What is a Fluid? The key distinction between a fluid and a solid lies in the mode of resistance to change of shape. The fluid, unlike the

More information

b) (5) Find the tension T B in the cord connected to the wall.

b) (5) Find the tension T B in the cord connected to the wall. General Physics I Quiz 6 - Ch. 9 - Static Equilibrium July 15, 2009 Name: Make your work clear to the grader. Show formulas used. Give correct units and significant figures. Partial credit is available

More information

[variable] = units (or dimension) of variable.

[variable] = units (or dimension) of variable. Dimensional Analysis Zoe Wyatt wyatt.zoe@gmail.com with help from Emanuel Malek Understanding units usually makes physics much easier to understand. It also gives a good method of checking if an answer

More information

FLUID MECHANICS. Chapter 3 Elementary Fluid Dynamics - The Bernoulli Equation

FLUID MECHANICS. Chapter 3 Elementary Fluid Dynamics - The Bernoulli Equation FLUID MECHANICS Chapter 3 Elementary Fluid Dynamics - The Bernoulli Equation CHAP 3. ELEMENTARY FLUID DYNAMICS - THE BERNOULLI EQUATION CONTENTS 3. Newton s Second Law 3. F = ma along a Streamline 3.3

More information

BACHELOR OF TECHNOLOGY IN MECHANICAL ENGINEERING (COMPUTER INTEGRATED MANUFACTURING)

BACHELOR OF TECHNOLOGY IN MECHANICAL ENGINEERING (COMPUTER INTEGRATED MANUFACTURING) No. of Printed Pages : 6 BME-028 BACHELOR OF TECHNOLOGY IN MECHANICAL ENGINEERING (COMPUTER INTEGRATED MANUFACTURING) Term-End Examination December, 2011 00792 BME-028 : FLUID MECHANICS Time : 3 hours

More information