12d Model. Civil and Surveying Software. Drainage Analysis Module Hydraulics. Owen Thornton BE (Mech), 12d Model Programmer.

Size: px
Start display at page:

Download "12d Model. Civil and Surveying Software. Drainage Analysis Module Hydraulics. Owen Thornton BE (Mech), 12d Model Programmer."

Transcription

1 1d Model Civil and Surveying Sotware Drainage Analysis Module Hydraulics Owen Thornton BE (Mech), 1d Model Programmer 04 June 007 Revised: 3 August 007 (V8C1i) 04 February 008 (V8C1p) This document deines the various terms relevant to the hydraulic calculations perormed by the Drainage Analysis module o 1d Model, including how and where they are calculated. The terms pipe and channel are sometimes used interchangeably, as are the terms pit, manhole, inlet and structure. Page 1 o 11

2 1d Model Drainage Analysis Module Hydraulics Deinitions: Q rat = Peak Flow The peak low rate or the pipe, without consideration o bypass lows. It is determined rom the contributing catchments via the Rational Method (and includes any direct pit or pipe low that may have been speciied upstream). It is shown in the Hydraulic Report as "Peak Flow Qrat", and is also set as a pipe attribute named "calculated peak low". Q b = Net Bypass Flow When considering bypass lows, Q b or the pipe is determined rom an analysis o all the upstream pits contributing to the pipe, as recommended in the Australian Rainall and Runo. It represents the sum o the peak bypass lows approaching these pits, minus the sum o the peak bypass lows leaving them. It is shown in the Hydraulic Report as "Net Bypass Flow Qb", and is also set as a pipe attribute named "calculated net bypass low". Note: the peak bypass low leaving each pit, is determined rom the pit inlet capacity data, deined or each pit type in the drainage.4d setup ile, as well as the relevant choke actor determined or each pit. Q = Pipe Flow = Q rat + Q b The peak low rate in the pipe, represented by the sum o Q rat and Q b. It is shown in the Hydraulic Report as "Pipe Flow Q", and is also set as a pipe attribute named "pipe low". Note: it is only when considering bypass lows, that Q may dier rom Q rat. Q x = Excess Pipe Flow I the pipe low, Q, is so large that the HGL would rise above the upstream pit s grate level, then Q x will represent the dierence between Q and the low rate that would keep the HGL just at the grate level. It is shown in the Hydraulic Report as "Excess Pipe Flow Qx", and is also set as a pipe attribute named "calculated excess low". Note: the excess low amount, Q x, is still included in the pipe low, Q, and is not automatically re-routed to the overland system. However, when considering bypass lows, the user may set the Qx routing increment to a value greater than zero, which will initiate extra analysis passes to re-route just enough low as is necessary, rom the pipe network to the overland system, so as to eradicate the excess pipe lows. At each extra pass, an amount no greater than the Qx routing increment is removed rom the pipe network rom the most upstream pipe(s) with excess low(s) and re-routed to the overland system. I low is entering rom the top o a pipe s upstream pit, the re-routing is achieved initially by reducing the pit s choke actor by an amount calculated to have the same eect. Once the choke actor is reduced to zero, however, any remaining Q x is re-routed as pit surcharge low, Q s. Q s = Pit Surcharge Flow When (and only when) excess pipe lows are re-routed to the overland system, it is possible or some pits to surcharge (low rising up and exiting the top o the pit). At such pits, the choke actor will have been reduced to zero, and Q s will have a positive value equal in magnitude to the negative pit inlow. In the Hydrology Report, a negative value o "Inlet Flow Qi" indicates a surcharge low, and Q s is also set as a pit attribute named "calculated surcharge low". Note: pit surcharge low is automatically included in the bypass low leaving a pit, and may re-enter the pipe network elsewhere. Page o 11

3 1d Model Drainage Analysis Module Hydraulics Deinitions: cont V = Full Pipe Velocity = Q / A The velocity in the pipe when the pipe low, Q, ills the entire cross-sectional area, A, o the pipe. This is the minimum velocity possible or this low rate. It is shown in the Hydraulic Report as "Full Pipe Vel V=Q/A", and is also set as a pipe attribute named "ull pipe velocity". Note: V is the velocity used to determine pressure head and water surace elevation losses through the upstream pit. Typically, the loss coeicients K u & K w only apply to pipes under pressure. Q cap = Capacity Flow For the particular size, grade and roughness o the pipe, and assuming no downstream tailwater restrictions, the capacity low is the low rate theoretically possible in the pipe, at the point where the low would become pressurised (i.e. lowing exactly ull). It is shown in the Hydraulic Report as "Capacity Flow Qcap", and is also set as a pipe attribute named "low capacity". V cap = Capacity Velocity = Q cap / A The velocity corresponding to Q cap. It is shown in the Hydraulic Report as "Capacity Vel Vcap=Qcap/A", and is also set as a pipe attribute named "capacity velocity". Note: V cap is sometimes reerred to by others as at grade velocity, or more conusingly, as ull pipe velocity. Great care should be taken, to avoid conusing V cap with V. Capacity Ratio = Q / Q cap This is simply the ratio o the pipe low to the capacity low. I greater than 1.0, Q will always be pressurised. I less than 1.0, Q may or may not be pressurised, depending on the conditions downstream. Some governing authorities speciy that it should always be less than 1.0. It is shown in the Hydraulic Report as "Q/Qcap Ratio", and is also set as a pipe attribute named "low capacity ratio". Q mcap = Max Capacity Flow Similar to Q cap, but representing the maximum unpressurised low rate theoretically possible in the pipe. For a circular pipe, Q mcap occurs at a depth o about 0.94xD. For a box-culvert, Q mcap occurs at a depth just below the obvert (0.999xH, say). For circular pipes, Q mcap is approximately 1.07xQ cap. For box-culverts, Q mcap may be considerably greater than Q cap, due to the sudden increase in riction losses when the low comes into contact with the top wall an eect more pronounced as the culvert's width/height ratio increases. Note: Q mcap is not calculated by 1d Model, as it is an inherently unstable low, which can become pressurised with only the slightest increase in rictional resistance. Pipe manuacturers typically publish capacities which match more closely to Q cap. V mcap = Max Capacity Velocity The velocity corresponding to Q mcap, that is: V mcap = Q mcap / A w, where A w is the wetted crosssectional area at the depth at which Q mcap occurs. Page 3 o 11

4 1d Model Drainage Analysis Module Hydraulics Deinitions: cont d n = Normal Depth The depth in the pipe when the slope o the water surace o the pipe low, Q, is parallel to the pipe slope. I Q is greater than Q cap, d n is set to the obvert o the pipe. It is set as a pipe attribute named "normal depth", and the value [d n / <pipe height>] is set as "normal depth relative". d c = Critical Depth The depth in the pipe when the local energy head (the sum o the pressure and velocity heads only, ignoring the gravity head) o the pipe low, Q, is at a minimum. It is set as a pipe attribute named "critical depth", and the value [d c / <pipe height>] is set as "critical depth relative". V n = Normal Depth Velocity The velocity in the pipe when the pipe low, Q, is lowing at the normal depth, d n. This is the maximum velocity possible or this low rate, in the most common case o a "steep" slope pipe (where d c > d n ). In the rare case o a "mild" slope pipe (where d c < d n ), it is possible or the velocity to be slightly greater near the downstream end o the pipe, i the low "drops o the end" and the depth approaches d c. It is shown in the Hydraulic Report as "Norm Depth Vel Vn=Q/An", and is also set as a pipe attribute named "normal velocity". V c = Critical Depth Velocity The velocity in the pipe when the pipe low, Q, is lowing at the critical depth, d c. When the low is slower than V c (deeper than d c ) it is termed tranquil low. When the low is aster than V c (shallower than d c ), it is termed rapid low. It is shown in the Hydraulic Report as "Crit Depth Vel Vc=Q/Ac", and is also set as a pipe attribute named "critical velocity". V min & V max = Allowable Velocity Ranges or V n and V cap These velocity limits are oten speciied by governing authorities, to ensure that all pipe lows are ast enough to wash away impediments, but not so ast as to scour the pipes. I set on the GLOBAL=>Main tab o the Drainage Network Editor, they are checked against the calculated V n and/or V cap values. I ever a calculated velocity is too low or too high, a new pipe grade is recommended in the Output Window, to help remedy the problem. V a = Actual Velocity (VicRoads manual) The Victorian "VicRoads" manual reers to a chart or determining the so-called actual velocity, V a, in part-ull pipes. The chart shows a relationship between Q / Q cap values and V a / V cap values. The resultant V a values rom this chart, are equivalent to the normal depth velocity, V n, values calculated by 1d Model. Page 4 o 11

5 Manning's Formula versus the Colebrook-White Formula: 1d Model Drainage Analysis Module Hydraulics The Drainage Analysis module allows pipe roughness to be speciied as either Manning's n (based on metre-second units), or Colebrook's k (speciied in mm in 1d). The choice o roughness type determines the ormula Manning or Colebrook-White used to calculate: Q cap, V cap, d n and V n. It also governs how the riction slope is determined in both the Darcy-Weisbach equation and the Gradually Varied Flow equation, when calculating the HGL values along the pipe. The Colebrook- White ormula may be seen as an empirical combination o the Rough and Smooth Pipe Laws o turbulent low, which were both derived rom boundary-layer theory by Prandtl and von Kármán, but adjusted to match the experimental results o Nikuradse, who perormed a series o lab tests on small pipes o uniorm roughness. Colebrook and White, however, perormed tests on a range o commercial pipes (o non-uniorm roughness) with an equivalent k deduced rom the constant riction actor,, observed at high Reynolds number and ound that or most o the pipes they tested, their new combination-ormula matched well. The turbulent range o the now widely-used Moody Diagram, is wholly based on the Colebrook-White ormula, and represents the trend to be expected, in the absence o any speciic data or particular pipes. Where non-circular pipes are used, or where part-ull low occurs in any kind o pipe or open channel o reasonably uniorm crosssection, substitution o 4R or D (our times the hydraulic radius or diameter) can be justiied, with the assumption that the mean shear-stress around the wetted perimeter is not too dissimilar rom the uniorm stress around a circular perimeter (true enough or box-culverts and many open channels). Because the Colebrook-White ormula accounts or the variations in dependent on the relative roughness (k/r or k/d) and the Reynolds number (Re), it is slightly more reliable, when considered across the range o pipe sizes and low rates commonly ound in stormwater systems. Most o the values published or Manning s n are or relatively large open channels, where the dependency on Re is slight, and relative roughness is implied in the n value. As such, Manning s ormula is good or larger systems (especially natural channels), but when applied to smaller systems like typical stormwater pipes, the Colebrook-White ormula suggests that these published n values should be reduced somewhat. Overall, the primary diiculty with both ormulae lies in the selection o suitable n or k values, and signiicant errors are not uncommon. The ollowing igure shows a normalised graph o Manning's ormula, or a ull range o low depths in both circular pipes and (square) box-culverts. (The corresponding Colebrook-White graph is so similar on this normalised scale, that it may be considered identical.) Note the dierence between Q cap and Q mcap on the graph. Page 5 o 11

6 1d Model Drainage Analysis Module Hydraulics The Hydraulic Grade Line (HGL): In 1d Model, when a Drainage string is proiled or plotted, you have the option to display the HGL determined rom a storm analysis o the drainage network. The HGL represents the peak sum o the pressure and gravity heads throughout the network, and in 1d, it is idealised to show separate head losses along the pipes and through the pits. In reality, these losses are not separate, but continuous, with the oten highly un-developed low near the pits, progressively orming ully-developed, onedimensional low, in the pipe reaches suiciently distant rom the pits. HGL Along Pipes: The HGL drawn along a pipe in 1d, is simply the straight line joining the pipe s idealised entrance and exit HGL levels. As such, in pipes where the steady low is wholly pressurised, it is a good representation o the riction slope, and consequent loss o total head ( H T ) due to riction. However, where part-ull low occurs in any portion o the pipe, neither the riction slope nor the water surace slope is constant, and so the straight line implies nothing other than the idealised entrance and exit HGL levels. For these cases, the idealised HGL is calculated internally, assuming ully-developed low, via numerical integration o the Gradually Varied Flow equation. This handles all possible cases o tranquil and rapid low on mild and steep slope pipes, including the hydraulic jumps that can occur on steep slopes. Note that, due to the non-uniorm velocity head in these cases, H T due to riction cannot be determined rom the idealised HGL, and must instead be determined rom the Total Energy Line (TEL). HGL At Pits: The horizontal HGL drawn across a pit, represents the peak water surace elevation (WSE) in that pit, and is tested against the reeboard and surcharge limits imposed there. The jump in the HGL between a pit s entrance and exit, represents the change (normally a loss) in pressure head ( H P ) through that pit (it does not represent the loss in total head). I a pit s entrance HGL level is higher than the level ormed by the minimum o d n and d c in an upstream pipe, then this HGL level also orms a tailwater condition or that upstream pipe. Note that WSE is typically equal to, or slightly greater than H P, and that both these jumps may, to a certain extent, be thought o as the eect that a pit has on what would otherwise be ully-developed, one-dimensional low. Schematic o a typical HGL in a steep slope pipe Page 6 o 11

7 1d Model Drainage Analysis Module Hydraulics Hydraulic Equations: Bernoulli s Equation (or the head o a streamline) V HT = HV + H P + HG = + h + g z Reynolds Number (laminar low < 000 < critical zone < 4000 < turbulent low) V D 4 V R Re = = ν ν Darcy-Weisbach Equation (or steady, uniorm [pressurised] low) H T V V m V = S = = = L D g 4R g R g Gradually Varied Flow Equation (or steady, non-uniorm [ree-surace] low) dh S0 S = dl V B 1 g Aw Manning's Formula (or complete turbulence, high Re) V g g R = = (Manning s relation to Chézy s coeicient, or metre-second units) m n 1 3 S R = (or metre-second units) OR n V 1 3 S R = 1.49 (or oot-second units) n Colebrook-White Formula (or transition zone low and complete turbulence, Re > 4000) 1 k.51 = log + 10 (as published by Colebrook, 1939) 3.7 D Re V = k.51ν = k gds log grs log D D gds 14.8 R Pressure Head Change Formula (through pit directly upstream o pipe) H = K V / g P u 0.314ν R grs WSE Change Formula (between pit directly upstream o pipe and pipe entrance) WSE = K V / g w Page 7 o 11

8 1d Model Drainage Analysis Module Hydraulics where: [dimensions] H T = total head (energy per unit weight o water) [L] H V = velocity head = V / g [L] H P = pressure head = h [L] H G = gravity head = z [L] V = mean velocity o low through a cross-section [L/T] g = acceleration due to gravity [L/T ] h = pressure head (and depth o low in an open channel) at a cross-section [L] z = height o channel invert at a cross-section, rom a constant horizontal datum [L] Re = Reynolds number [-] ν = kinematic viscosity o water [L /T] D = diameter o circular pipe [L] R = hydraulic radius o low at a cross-section = A w /P w = D/4 or ull circular pipe [L] A w = wetted cross-sectional area [L ] P w = wetted cross-sectional perimeter [L] L = plan length o channel [L] = Darcy riction actor (based on D) [-] m = Fanning riction actor (based on R) = /4 conusingly, oten denoted by [-] dh/dl = longitudinal slope o water surace at a cross-section, relative to S 0 [-] B = lateral breadth o water surace at a cross-section [L] S 0 = channel slope [-] S = riction slope (energy lost, per unit weight o water, per unit length o channel) [-] S = context dependent typically: S 0 when solving or V; S when solving or S [-] n = Manning roughness actor [T/L 1/3 ] k = Colebrook roughness actor [L] WSE = water surace elevation in pit [L] K u = pressure head change actor or pit directly upstream o pipe [-] K w = WSE change actor or pit directly upstream o pipe [-] V = ull pipe velocity [L/T] Page 8 o 11

9 1d Model Drainage Analysis Module Hydraulics Determining the Critical and Normal Depths in Part-ull Pipes: Wherever the pipe low, Q, is less than the capacity low, Q cap, the potential exists or part-ull (ree surace) low to occur. In these instances, the critical and normal low depths are determined by 1d Model, using the equations shown in the igure below. Note that the graph within the igure, shows the solutions or a circular pipe on a normalised scale. Page 9 o 11

10 Page 10 o 11 1d Model Drainage Analysis Module Hydraulics

11 More Hydraulic Equations (or reerence only not used in 1d): Chézy s Formula (or complete turbulence, high Re) 8gRS V = = C R S (C is Chézy s coeicient) Laminar Flow Law (or Re < 000) 64 = (via Poiseuille s ormula) Re 1d Model Drainage Analysis Module Hydraulics Smooth Pipe Law (or Re > 4000, very low k/d) 1.51 = log 10 (adjusted to Nikuradse s data rom uniorm roughness pipes) Re log10 (Colebrook s approximation: within ±1.5% or 5000 < Re < 10 8 ) Re 5.76 log Re Rough Pipe Law (or complete turbulence, high Re) 1 k = log10 (adjusted to Nikuradse s data rom uniorm roughness pipes) 3. 7 D 170 D Re > (range o Rough Pipe Law, based on Nikuradse s observations) k 1650D Re > (range o Rough Pipe Law, based on C-W ormula, or accurate to < 1%) k Converting k to n (by equating Manning s ormula to the Colebrook-White ormula) n = R 1 6 k 4 g log R 0.314ν R grs Sources: Colebrook, C.F., 1939, Turbulent Flow in Pipes with particular reerence to the Transition Region between the Smooth and Rough Pipe Laws, J. Instn. Civ. Engrs., Vol. 11, Massey, B.S., 1989, Mechanics o Fluids, 6 th Ed., Chapman & Hall. Pilgrim, D.H. (Ed.), 1987, Australian Rainall and Runo, Vol. 1, Instn. Engrs. Aust. Page 11 o 11

12d Model. Civil and Surveying Software. Version 7. Drainage Analysis Module Hydraulics. Owen Thornton BE (Mech), 12d Model Programmer

12d Model. Civil and Surveying Software. Version 7. Drainage Analysis Module Hydraulics. Owen Thornton BE (Mech), 12d Model Programmer 1d Model Civil and Surveying Sotware Version 7 Drainage Analysis Module Hydraulics Owen Thornton BE (Mech), 1d Model Programmer owen.thornton@1d.com 9 December 005 Revised: 10 January 006 8 February 007

More information

Chapter 3 Water Flow in Pipes

Chapter 3 Water Flow in Pipes The Islamic University o Gaza Faculty o Engineering Civil Engineering Department Hydraulics - ECI 33 Chapter 3 Water Flow in Pipes 3. Description o A Pipe Flow Water pipes in our homes and the distribution

More information

CEE 3310 Open Channel Flow,, Nov. 18,

CEE 3310 Open Channel Flow,, Nov. 18, CEE 3310 Open Channel Flow,, Nov. 18, 2016 165 8.1 Review Drag & Lit Laminar vs Turbulent Boundary Layer Turbulent boundary layers stay attached to bodies longer Narrower wake! Lower pressure drag! C D

More information

OE4625 Dredge Pumps and Slurry Transport. Vaclav Matousek October 13, 2004

OE4625 Dredge Pumps and Slurry Transport. Vaclav Matousek October 13, 2004 OE465 Vaclav Matousek October 13, 004 1 Dredge Vermelding Pumps onderdeel and Slurry organisatie Transport OE465 Vaclav Matousek October 13, 004 Dredge Vermelding Pumps onderdeel and Slurry organisatie

More information

Pressure Head: Pressure head is the height of a column of water that would exert a unit pressure equal to the pressure of the water.

Pressure Head: Pressure head is the height of a column of water that would exert a unit pressure equal to the pressure of the water. Design Manual Chapter - Stormwater D - Storm Sewer Design D- Storm Sewer Sizing A. Introduction The purpose of this section is to outline the basic hydraulic principles in order to determine the storm

More information

CIE4491 Lecture. Hydraulic design

CIE4491 Lecture. Hydraulic design CIE4491 Lecture. Hydraulic design Marie-claire ten Veldhuis 19-9-013 Delft University of Technology Challenge the future Hydraulic design of urban stormwater systems Focus on sewer pipes Pressurized and

More information

Department of Hydro Sciences, Institute for Urban Water Management. Urban Water

Department of Hydro Sciences, Institute for Urban Water Management. Urban Water Department of Hydro Sciences, Institute for Urban Water Management Urban Water 1 Global water aspects Introduction to urban water management 3 Basics for systems description 4 Water transport 5 Matter

More information

When water (fluid) flows in a pipe, for example from point A to point B, pressure drop will occur due to the energy losses (major and minor losses).

When water (fluid) flows in a pipe, for example from point A to point B, pressure drop will occur due to the energy losses (major and minor losses). PRESSURE DROP AND OSSES IN PIPE When water (luid) lows in a pipe, or example rom point A to point B, pressure drop will occur due to the energy losses (major and minor losses). A B Bernoulli equation:

More information

RESOLUTION MSC.362(92) (Adopted on 14 June 2013) REVISED RECOMMENDATION ON A STANDARD METHOD FOR EVALUATING CROSS-FLOODING ARRANGEMENTS

RESOLUTION MSC.362(92) (Adopted on 14 June 2013) REVISED RECOMMENDATION ON A STANDARD METHOD FOR EVALUATING CROSS-FLOODING ARRANGEMENTS (Adopted on 4 June 203) (Adopted on 4 June 203) ANNEX 8 (Adopted on 4 June 203) MSC 92/26/Add. Annex 8, page THE MARITIME SAFETY COMMITTEE, RECALLING Article 28(b) o the Convention on the International

More information

Uniform Channel Flow Basic Concepts Hydromechanics VVR090

Uniform Channel Flow Basic Concepts Hydromechanics VVR090 Uniform Channel Flow Basic Concepts Hydromechanics VVR090 ppt by Magnus Larson; revised by Rolf L Feb 2014 SYNOPSIS 1. Definition of Uniform Flow 2. Momentum Equation for Uniform Flow 3. Resistance equations

More information

Uniform Channel Flow Basic Concepts. Definition of Uniform Flow

Uniform Channel Flow Basic Concepts. Definition of Uniform Flow Uniform Channel Flow Basic Concepts Hydromechanics VVR090 Uniform occurs when: Definition of Uniform Flow 1. The depth, flow area, and velocity at every cross section is constant 2. The energy grade line,

More information

39.1 Gradually Varied Unsteady Flow

39.1 Gradually Varied Unsteady Flow 39.1 Gradually Varied Unsteady Flow Gradually varied unsteady low occurs when the low variables such as the low depth and velocity do not change rapidly in time and space. Such lows are very common in

More information

FE Fluids Review March 23, 2012 Steve Burian (Civil & Environmental Engineering)

FE Fluids Review March 23, 2012 Steve Burian (Civil & Environmental Engineering) Topic: Fluid Properties 1. If 6 m 3 of oil weighs 47 kn, calculate its specific weight, density, and specific gravity. 2. 10.0 L of an incompressible liquid exert a force of 20 N at the earth s surface.

More information

FLOW IN CONDUITS. Shear stress distribution across a pipe section. Chapter 10

FLOW IN CONDUITS. Shear stress distribution across a pipe section. Chapter 10 Chapter 10 Shear stress distribution across a pipe section FLOW IN CONDUITS For steady, uniform flow, the momentum balance in s for the fluid cylinder yields Fluid Mechanics, Spring Term 2010 Velocity

More information

HEADLOSS ESTIMATION. Mekanika Fluida 1 HST

HEADLOSS ESTIMATION. Mekanika Fluida 1 HST HEADLOSS ESTIMATION Mekanika Fluida HST Friction Factor : Major losses Laminar low Hagen-Poiseuille Turbulent (Smoot, Transition, Roug) Colebrook Formula Moody diagram Swamee-Jain 3 Laminar Flow Friction

More information

OPEN CHANNEL FLOW. One-dimensional - neglect vertical and lateral variations in velocity. In other words, Q v = (1) A. Figure 1. One-dimensional Flow

OPEN CHANNEL FLOW. One-dimensional - neglect vertical and lateral variations in velocity. In other words, Q v = (1) A. Figure 1. One-dimensional Flow OPEN CHANNEL FLOW Page 1 OPEN CHANNEL FLOW Open Channel Flow (OCF) is flow with one boundary exposed to atmospheric pressure. The flow is not pressurized and occurs because of gravity. Flow Classification

More information

A note on critical flow section in collector channels

A note on critical flow section in collector channels Sādhan ā, Vol. 26, Part 5, October 2001, pp. 439 445. Printed in India A note on critical flow section in collector channels 1. Introduction SUBHASISH DEY Department of Civil Engineering, Indian Institute

More information

Review of pipe flow: Friction & Minor Losses

Review of pipe flow: Friction & Minor Losses ENVE 204 Lecture -1 Review of pipe flow: Friction & Minor Losses Assist. Prof. Neslihan SEMERCİ Marmara University Department of Environmental Engineering Important Definitions Pressure Pipe Flow: Refers

More information

Presented by: Civil Engineering Academy

Presented by: Civil Engineering Academy Presented by: Civil Engineering Academy Open-Channel Flow Uniform Flow (See CERM Ch. 19) Characterized by constant depth volume, and cross section. It can be steady or unsteady Non-uniform Flow *Not on

More information

Hydraulics for Urban Storm Drainage

Hydraulics for Urban Storm Drainage Urban Hydraulics Hydraulics for Urban Storm Drainage Learning objectives: understanding of basic concepts of fluid flow and how to analyze conduit flows, free surface flows. to analyze, hydrostatic pressure

More information

Viscous Flow in Ducts

Viscous Flow in Ducts Dr. M. Siavashi Iran University of Science and Technology Spring 2014 Objectives 1. Have a deeper understanding of laminar and turbulent flow in pipes and the analysis of fully developed flow 2. Calculate

More information

Hydraulics. B.E. (Civil), Year/Part: II/II. Tutorial solutions: Pipe flow. Tutorial 1

Hydraulics. B.E. (Civil), Year/Part: II/II. Tutorial solutions: Pipe flow. Tutorial 1 Hydraulics B.E. (Civil), Year/Part: II/II Tutorial solutions: Pipe flow Tutorial 1 -by Dr. K.N. Dulal Laminar flow 1. A pipe 200mm in diameter and 20km long conveys oil of density 900 kg/m 3 and viscosity

More information

UNIFORM FLOW CRITICAL FLOW GRADUALLY VARIED FLOW

UNIFORM FLOW CRITICAL FLOW GRADUALLY VARIED FLOW UNIFORM FLOW CRITICAL FLOW GRADUALLY VARIED FLOW Derivation of uniform flow equation Dimensional analysis Computation of normal depth UNIFORM FLOW 1. Uniform flow is the flow condition obtained from a

More information

DEPARTMENT OF CIVIL AND ENVIRONMENTAL ENGINEERING Urban Drainage: Hydraulics. Solutions to problem sheet 2: Flows in open channels

DEPARTMENT OF CIVIL AND ENVIRONMENTAL ENGINEERING Urban Drainage: Hydraulics. Solutions to problem sheet 2: Flows in open channels DEPRTMENT OF CIVIL ND ENVIRONMENTL ENGINEERING Urban Drainage: Hydraulics Solutions to problem sheet 2: Flows in open channels 1. rectangular channel of 1 m width carries water at a rate 0.1 m 3 /s. Plot

More information

We will assume straight channels with simple geometries (prismatic channels) and steady state flow (in time).

We will assume straight channels with simple geometries (prismatic channels) and steady state flow (in time). 56 Review Drag & Lift Laminar vs Turbulent Boundary Layer Turbulent boundary layers stay attached to bodies longer Narrower wake! Lower pressure drag! 8. Open-Channel Flow Pipe/duct flow closed, full,

More information

1-Reynold s Experiment

1-Reynold s Experiment Lect.No.8 2 nd Semester Flow Dynamics in Closed Conduit (Pipe Flow) 1 of 21 The flow in closed conduit ( flow in pipe ) is differ from this occur in open channel where the flow in pipe is at a pressure

More information

Lecture Note for Open Channel Hydraulics

Lecture Note for Open Channel Hydraulics Chapter -one Introduction to Open Channel Hydraulics 1.1 Definitions Simply stated, Open channel flow is a flow of liquid in a conduit with free space. Open channel flow is particularly applied to understand

More information

Hydraulic validation of the LHC cold mass heat exchanger tube.

Hydraulic validation of the LHC cold mass heat exchanger tube. Hydraulic validation o te LHC cold mass eat excanger tube. LHC Project Note 155 1998-07-22 (pilippe.provenaz@cern.c) Pilippe PROVENAZ / LHC-ACR Division Summary Te knowledge o te elium mass low vs. te

More information

An Improved Expression for a Classical Type of Explicit Approximation of the Colebrook White Equation with Only One Internal Iteration

An Improved Expression for a Classical Type of Explicit Approximation of the Colebrook White Equation with Only One Internal Iteration International Journal o Hydraulic Engineering 06, 5(): 9-3 DOI: 0.593/j.ijhe.06050.03 An Improved Expression or a Classical Type o Explicit Approximation o the Colebrook White Equation with Only One Internal

More information

ME 305 Fluid Mechanics I. Part 8 Viscous Flow in Pipes and Ducts. Flow in Pipes and Ducts. Flow in Pipes and Ducts (cont d)

ME 305 Fluid Mechanics I. Part 8 Viscous Flow in Pipes and Ducts. Flow in Pipes and Ducts. Flow in Pipes and Ducts (cont d) ME 305 Fluid Mechanics I Flow in Pipes and Ducts Flow in closed conduits (circular pipes and non-circular ducts) are very common. Part 8 Viscous Flow in Pipes and Ducts These presentations are prepared

More information

Chapter (3) Water Flow in Pipes

Chapter (3) Water Flow in Pipes Chapter (3) Water Flow in Pipes Water Flow in Pipes Bernoulli Equation Recall fluid mechanics course, the Bernoulli equation is: P 1 ρg + v 1 g + z 1 = P ρg + v g + z h P + h T + h L Here, we want to study

More information

Chapter 8: Flow in Pipes

Chapter 8: Flow in Pipes Objectives 1. Have a deeper understanding of laminar and turbulent flow in pipes and the analysis of fully developed flow 2. Calculate the major and minor losses associated with pipe flow in piping networks

More information

EXPERIMENT No.1 FLOW MEASUREMENT BY ORIFICEMETER

EXPERIMENT No.1 FLOW MEASUREMENT BY ORIFICEMETER EXPERIMENT No.1 FLOW MEASUREMENT BY ORIFICEMETER 1.1 AIM: To determine the co-efficient of discharge of the orifice meter 1.2 EQUIPMENTS REQUIRED: Orifice meter test rig, Stopwatch 1.3 PREPARATION 1.3.1

More information

Hydraulics and hydrology

Hydraulics and hydrology Hydraulics and hydrology - project exercises - Class 4 and 5 Pipe flow Discharge (Q) (called also as the volume flow rate) is the volume of fluid that passes through an area per unit time. The discharge

More information

Hydraulic Design Of Polyethylene Pipes

Hydraulic Design Of Polyethylene Pipes Hydraulic Design Of Polyethylene Pipes Waters & Farr polyethylene pipes offer a hydraulically smooth bore that provides excellent flow characteristics. Other advantages of Waters & Farr polyethylene pipes,

More information

FLUID MECHANICS. Dynamics of Viscous Fluid Flow in Closed Pipe: Darcy-Weisbach equation for flow in pipes. Major and minor losses in pipe lines.

FLUID MECHANICS. Dynamics of Viscous Fluid Flow in Closed Pipe: Darcy-Weisbach equation for flow in pipes. Major and minor losses in pipe lines. FLUID MECHANICS Dynamics of iscous Fluid Flow in Closed Pipe: Darcy-Weisbach equation for flow in pipes. Major and minor losses in pipe lines. Dr. Mohsin Siddique Assistant Professor Steady Flow Through

More information

Chapter 8: Flow in Pipes

Chapter 8: Flow in Pipes 8-1 Introduction 8-2 Laminar and Turbulent Flows 8-3 The Entrance Region 8-4 Laminar Flow in Pipes 8-5 Turbulent Flow in Pipes 8-6 Fully Developed Pipe Flow 8-7 Minor Losses 8-8 Piping Networks and Pump

More information

Closed duct flows are full of fluid, have no free surface within, and are driven by a pressure gradient along the duct axis.

Closed duct flows are full of fluid, have no free surface within, and are driven by a pressure gradient along the duct axis. OPEN CHANNEL FLOW Open channel flow is a flow of liquid, basically water in a conduit with a free surface. The open channel flows are driven by gravity alone, and the pressure gradient at the atmospheric

More information

Open Channel Flow Part 2. Ch 10 Young, notes, handouts

Open Channel Flow Part 2. Ch 10 Young, notes, handouts Open Channel Flow Part 2 Ch 10 Young, notes, handouts Uniform Channel Flow Many situations have a good approximation d(v,y,q)/dx=0 Uniform flow Look at extended Bernoulli equation Friction slope exactly

More information

CEE 3310 Open Channel Flow, Nov. 26,

CEE 3310 Open Channel Flow, Nov. 26, CEE 3310 Open Channel Flow, Nov. 6, 018 175 8.10 Review Open Channel Flow Gravity friction balance. y Uniform Flow x = 0 z = S 0L = h f y Rapidly Varied Flow x 1 y Gradually Varied Flow x 1 In general

More information

Basic Fluid Mechanics

Basic Fluid Mechanics Basic Fluid Mechanics Chapter 6A: Internal Incompressible Viscous Flow 4/16/2018 C6A: Internal Incompressible Viscous Flow 1 6.1 Introduction For the present chapter we will limit our study to incompressible

More information

FACULTY OF CHEMICAL & ENERGY ENGINEERING FLUID MECHANICS LABORATORY TITLE OF EXPERIMENT: MINOR LOSSES IN PIPE (E4)

FACULTY OF CHEMICAL & ENERGY ENGINEERING FLUID MECHANICS LABORATORY TITLE OF EXPERIMENT: MINOR LOSSES IN PIPE (E4) FACULTY OF CHEMICAL & ENERGY ENGINEERING FLUID MECHANICS LABORATORY TITLE OF EXPERIMENT: MINOR LOSSES IN PIPE (E4) 1 1.0 Objectives The objective of this experiment is to calculate loss coefficient (K

More information

88 MODERN SEWER DESIGN

88 MODERN SEWER DESIGN 88 MODERN SEWER DESIGN Fabricated fittings reduce head losses in the system. 4. HYDRAULICS OF STORM SEWERS CHAPTER 4 Hydraulics of Storm Sewers 89 Storm sewers may be designed as either open channels,

More information

FLOW FRICTION CHARACTERISTICS OF CONCRETE PRESSURE PIPE

FLOW FRICTION CHARACTERISTICS OF CONCRETE PRESSURE PIPE 11 ACPPA TECHNICAL SERIES FLOW FRICTION CHARACTERISTICS OF CONCRETE PRESSURE PIPE This paper presents formulas to assist in hydraulic design of concrete pressure pipe. There are many formulas to calculate

More information

ME 305 Fluid Mechanics I. Chapter 8 Viscous Flow in Pipes and Ducts

ME 305 Fluid Mechanics I. Chapter 8 Viscous Flow in Pipes and Ducts ME 305 Fluid Mechanics I Chapter 8 Viscous Flow in Pipes and Ducts These presentations are prepared by Dr. Cüneyt Sert Department of Mechanical Engineering Middle East Technical University Ankara, Turkey

More information

LECTURE 6- ENERGY LOSSES IN HYDRAULIC SYSTEMS SELF EVALUATION QUESTIONS AND ANSWERS

LECTURE 6- ENERGY LOSSES IN HYDRAULIC SYSTEMS SELF EVALUATION QUESTIONS AND ANSWERS LECTURE 6- ENERGY LOSSES IN HYDRAULIC SYSTEMS SELF EVALUATION QUESTIONS AND ANSWERS 1. What is the head loss ( in units of bars) across a 30mm wide open gate valve when oil ( SG=0.9) flow through at a

More information

REE 307 Fluid Mechanics II. Lecture 1. Sep 27, Dr./ Ahmed Mohamed Nagib Elmekawy. Zewail City for Science and Technology

REE 307 Fluid Mechanics II. Lecture 1. Sep 27, Dr./ Ahmed Mohamed Nagib Elmekawy. Zewail City for Science and Technology REE 307 Fluid Mechanics II Lecture 1 Sep 27, 2017 Dr./ Ahmed Mohamed Nagib Elmekawy Zewail City for Science and Technology Course Materials drahmednagib.com 2 COURSE OUTLINE Fundamental of Flow in pipes

More information

Pressure and Flow Characteristics

Pressure and Flow Characteristics Pressure and Flow Characteristics Continuing Education from the American Society of Plumbing Engineers August 2015 ASPE.ORG/ReadLearnEarn CEU 226 READ, LEARN, EARN Note: In determining your answers to

More information

Advanced Hydraulics Prof. Dr. Suresh A. Kartha Department of Civil Engineering Indian Institute of Technology, Guwahati

Advanced Hydraulics Prof. Dr. Suresh A. Kartha Department of Civil Engineering Indian Institute of Technology, Guwahati Advanced Hydraulics Prof. Dr. Suresh A. Kartha Department of Civil Engineering Indian Institute of Technology, Guwahati Module - 2 Uniform Flow Lecture - 1 Introduction to Uniform Flow Good morning everyone,

More information

ROAD MAP... D-1: Aerodynamics of 3-D Wings D-2: Boundary Layer and Viscous Effects D-3: XFLR (Aerodynamics Analysis Tool)

ROAD MAP... D-1: Aerodynamics of 3-D Wings D-2: Boundary Layer and Viscous Effects D-3: XFLR (Aerodynamics Analysis Tool) AE301 Aerodynamics I UNIT D: Applied Aerodynamics ROAD MAP... D-1: Aerodynamics o 3-D Wings D-2: Boundary Layer and Viscous Eects D-3: XFLR (Aerodynamics Analysis Tool) AE301 Aerodynamics I : List o Subjects

More information

FLUID MECHANICS PROF. DR. METİN GÜNER COMPILER

FLUID MECHANICS PROF. DR. METİN GÜNER COMPILER FLUID MECHANICS PROF. DR. METİN GÜNER COMPILER ANKARA UNIVERSITY FACULTY OF AGRICULTURE DEPARTMENT OF AGRICULTURAL MACHINERY AND TECHNOLOGIES ENGINEERING 1 5. FLOW IN PIPES 5.1.3. Pressure and Shear Stress

More information

Piping Systems and Flow Analysis (Chapter 3)

Piping Systems and Flow Analysis (Chapter 3) Piping Systems and Flow Analysis (Chapter 3) 2 Learning Outcomes (Chapter 3) Losses in Piping Systems Major losses Minor losses Pipe Networks Pipes in series Pipes in parallel Manifolds and Distribution

More information

Chapter (3) Water Flow in Pipes

Chapter (3) Water Flow in Pipes Chapter (3) Water Flow in Pipes Water Flow in Pipes Bernoulli Equation Recall fluid mechanics course, the Bernoulli equation is: P 1 ρg + v 1 g + z 1 = P ρg + v g + z h P + h T + h L Here, we want to study

More information

Chapter 10 Flow in Conduits

Chapter 10 Flow in Conduits Chapter 10 Flow in Conduits 10.1 Classifying Flow Laminar Flow and Turbulent Flow Laminar flow Unpredictable Turbulent flow Near entrance: undeveloped developing flow In developing flow, the wall shear

More information

Figure 34: Coordinate system for the flow in open channels.

Figure 34: Coordinate system for the flow in open channels. OE466 redging Processes 5. SCOUR 5.. Steady uniform flow in open channels This chapter is written with a view to bottom scour. The main outcome is the scour velocity as a function of the particle diameter.

More information

Available online at ScienceDirect. Energy Procedia 83 (2015 ) Václav Dvo ák a *, Tomáš Vít a

Available online at   ScienceDirect. Energy Procedia 83 (2015 ) Václav Dvo ák a *, Tomáš Vít a Available online at www.sciencedirect.com ScienceDirect Energy Procedia 83 (205 ) 34 349 7th International Conerence on Sustainability in Energy and Buildings Numerical investigation o counter low plate

More information

Chapter 6. Losses due to Fluid Friction

Chapter 6. Losses due to Fluid Friction Chapter 6 Losses due to Fluid Friction 1 Objectives ä To measure the pressure drop in the straight section of smooth, rough, and packed pipes as a function of flow rate. ä To correlate this in terms of

More information

8.3 Design of Base Plate for Thickness

8.3 Design of Base Plate for Thickness 8.3 Design o Base Plate or Thickness 8.3.1 Design o base plate or thickness (Elastic Design) Upto this point, the chie concern has been about the concrete oundation, and methods o design have been proposed

More information

Chapter 6. Losses due to Fluid Friction

Chapter 6. Losses due to Fluid Friction Chapter 6 Losses due to Fluid Friction 1 Objectives To measure the pressure drop in the straight section of smooth, rough, and packed pipes as a function of flow rate. To correlate this in terms of the

More information

Reynolds, an engineering professor in early 1880 demonstrated two different types of flow through an experiment:

Reynolds, an engineering professor in early 1880 demonstrated two different types of flow through an experiment: 7 STEADY FLOW IN PIPES 7.1 Reynolds Number Reynolds, an engineering professor in early 1880 demonstrated two different types of flow through an experiment: Laminar flow Turbulent flow Reynolds apparatus

More information

Friction Factors and Drag Coefficients

Friction Factors and Drag Coefficients Levicky 1 Friction Factors and Drag Coefficients Several equations that we have seen have included terms to represent dissipation of energy due to the viscous nature of fluid flow. For example, in the

More information

vector H. If O is the point about which moments are desired, the angular moment about O is given:

vector H. If O is the point about which moments are desired, the angular moment about O is given: The angular momentum A control volume analysis can be applied to the angular momentum, by letting B equal to angularmomentum vector H. If O is the point about which moments are desired, the angular moment

More information

FE Exam Fluids Review October 23, Important Concepts

FE Exam Fluids Review October 23, Important Concepts FE Exam Fluids Review October 3, 013 mportant Concepts Density, specific volume, specific weight, specific gravity (Water 1000 kg/m^3, Air 1. kg/m^3) Meaning & Symbols? Stress, Pressure, Viscosity; Meaning

More information

Signature: (Note that unsigned exams will be given a score of zero.)

Signature: (Note that unsigned exams will be given a score of zero.) Neatly print your name: Signature: (Note that unsigned exams will be given a score of zero.) Circle your lecture section (-1 point if not circled, or circled incorrectly): Prof. Dabiri Prof. Wassgren Prof.

More information

Chapter 8 Laminar Flows with Dependence on One Dimension

Chapter 8 Laminar Flows with Dependence on One Dimension Chapter 8 Laminar Flows with Dependence on One Dimension Couette low Planar Couette low Cylindrical Couette low Planer rotational Couette low Hele-Shaw low Poiseuille low Friction actor and Reynolds number

More information

Hydromechanics: Course Summary

Hydromechanics: Course Summary Hydromechanics: Course Summary Hydromechanics VVR090 Material Included; French: Chapters to 9 and 4 + Sample problems Vennard & Street: Chapters 8 + 3, and (part of it) Roberson & Crowe: Chapter Collection

More information

Lesson 6 Review of fundamentals: Fluid flow

Lesson 6 Review of fundamentals: Fluid flow Lesson 6 Review of fundamentals: Fluid flow The specific objective of this lesson is to conduct a brief review of the fundamentals of fluid flow and present: A general equation for conservation of mass

More information

Rock Sizing for Batter Chutes

Rock Sizing for Batter Chutes Rock Sizing for Batter Chutes STORMWATER MANAGEMENT PRACTICES Photo 1 Rock-lined batter chute Photo 2 Rock-lined batter chute 1. Introduction In the stormwater industry a chute is a steep drainage channel,

More information

Buoyancy Driven Heat Transfer of Water-Based CuO Nanofluids in a Tilted Enclosure with a Heat Conducting Solid Cylinder on its Center

Buoyancy Driven Heat Transfer of Water-Based CuO Nanofluids in a Tilted Enclosure with a Heat Conducting Solid Cylinder on its Center July 4-6 2012 London U.K. Buoyancy Driven Heat Transer o Water-Based CuO Nanoluids in a Tilted Enclosure with a Heat Conducting Solid Cylinder on its Center Ahmet Cihan Kamil Kahveci and Çiğdem Susantez

More information

Atmospheric pressure. 9 ft. 6 ft

Atmospheric pressure. 9 ft. 6 ft Name CEE 4 Final Exam, Aut 00; Answer all questions; 145 points total. Some information that might be helpful is provided below. A Moody diagram is printed on the last page. For water at 0 o C (68 o F):

More information

CONVECTIVE HEAT TRANSFER CHARACTERISTICS OF NANOFLUIDS. Convective heat transfer analysis of nanofluid flowing inside a

CONVECTIVE HEAT TRANSFER CHARACTERISTICS OF NANOFLUIDS. Convective heat transfer analysis of nanofluid flowing inside a Chapter 4 CONVECTIVE HEAT TRANSFER CHARACTERISTICS OF NANOFLUIDS Convective heat transer analysis o nanoluid lowing inside a straight tube o circular cross-section under laminar and turbulent conditions

More information

150A Review Session 2/13/2014 Fluid Statics. Pressure acts in all directions, normal to the surrounding surfaces

150A Review Session 2/13/2014 Fluid Statics. Pressure acts in all directions, normal to the surrounding surfaces Fluid Statics Pressure acts in all directions, normal to the surrounding surfaces or Whenever a pressure difference is the driving force, use gauge pressure o Bernoulli equation o Momentum balance with

More information

ACCOUNTING FOR FRICTION IN THE BERNOULLI EQUATION FOR FLOW THROUGH PIPES

ACCOUNTING FOR FRICTION IN THE BERNOULLI EQUATION FOR FLOW THROUGH PIPES ACCOUNTING FOR FRICTION IN THE BERNOULLI EQUATION FOR FLOW THROUGH PIPES Some background information first: We have seen that a major limitation of the Bernoulli equation is that it does not account for

More information

VARIED FLOW IN OPEN CHANNELS

VARIED FLOW IN OPEN CHANNELS Chapter 15 Open Channels vs. Closed Conduits VARIED FLOW IN OPEN CHANNELS Fluid Mechanics, Spring Term 2011 In a closed conduit there can be a pressure gradient that drives the flow. An open channel has

More information

FLOW CHARACTERISTICS OF HFC-134a IN AN ADIABATIC HELICAL CAPILLARY TUBE

FLOW CHARACTERISTICS OF HFC-134a IN AN ADIABATIC HELICAL CAPILLARY TUBE E HEFAT7 5 th International Conerence on Heat Transer, Fluid Mechanics and Thermodynamics Sun City, South Arica Paper number: KM1 FLOW CHARACTERISTICS OF HFC-1a IN AN ADIABATIC HELICAL CAPILLARY TUBE Khan

More information

HYDRAULIC STRUCTURES, EQUIPMENT AND WATER DATA ACQUISITION SYSTEMS - Vol. I Fluid Mechanics in Pipelines - D. Stephenson

HYDRAULIC STRUCTURES, EQUIPMENT AND WATER DATA ACQUISITION SYSTEMS - Vol. I Fluid Mechanics in Pipelines - D. Stephenson FLUID MECHANICS IN PIPELINES D. Stephenson Water Utilisation Division, University of Pretoria, Pretoria, South Africa Keywords: Flow, turbulence, pipelines, water hammer, head-loss, friction, waterworks,

More information

Turbulence is a ubiquitous phenomenon in environmental fluid mechanics that dramatically affects flow structure and mixing.

Turbulence is a ubiquitous phenomenon in environmental fluid mechanics that dramatically affects flow structure and mixing. Turbulence is a ubiquitous phenomenon in environmental fluid mechanics that dramatically affects flow structure and mixing. Thus, it is very important to form both a conceptual understanding and a quantitative

More information

Chapter 8 Flow in Pipes. Piping Systems and Pump Selection

Chapter 8 Flow in Pipes. Piping Systems and Pump Selection Piping Systems and Pump Selection 8-6C For a piping system that involves two pipes o dierent diameters (but o identical length, material, and roughness connected in series, (a the low rate through both

More information

Theory and equations for Craters from Impacts and Explosions. Keith A. Holsapple

Theory and equations for Craters from Impacts and Explosions. Keith A. Holsapple Theory and equations or Craters rom Impacts and Explosions Keith A. Holsapple 1. Dimensionless Forms As the primary example, the volume V o a crater ormed by a given impact can be expected to depend on

More information

Open Channel Flow I - The Manning Equation and Uniform Flow COURSE CONTENT

Open Channel Flow I - The Manning Equation and Uniform Flow COURSE CONTENT Open Channel Flow I - The Manning Equation and Uniform Flow Harlan H. Bengtson, PhD, P.E. COURSE CONTENT 1. Introduction Flow of a liquid may take place either as open channel flow or pressure flow. Pressure

More information

Applied Fluid Mechanics

Applied Fluid Mechanics Applied Fluid Mechanics 1. The Nature of Fluid and the Study of Fluid Mechanics 2. Viscosity of Fluid 3. Pressure Measurement 4. Forces Due to Static Fluid 5. Buoyancy and Stability 6. Flow of Fluid and

More information

Open Channel Flow - General. Hydromechanics VVR090

Open Channel Flow - General. Hydromechanics VVR090 Open Channel Flow - General Hydromechanics VVR090 ppt by Magnus Larson; revised by Rolf L Jan 2014, Feb 2015 SYNOPSIS 1. Introduction and Applications 2. The History of Open Channel Flow 3. Flow Classification

More information

INSTITUTE OF AERONAUTICAL ENGINEERING Dundigal, Hyderabad AERONAUTICAL ENGINEERING QUESTION BANK : AERONAUTICAL ENGINEERING.

INSTITUTE OF AERONAUTICAL ENGINEERING Dundigal, Hyderabad AERONAUTICAL ENGINEERING QUESTION BANK : AERONAUTICAL ENGINEERING. Course Name Course Code Class Branch INSTITUTE OF AERONAUTICAL ENGINEERING Dundigal, Hyderabad - 00 0 AERONAUTICAL ENGINEERING : Mechanics of Fluids : A00 : II-I- B. Tech Year : 0 0 Course Coordinator

More information

Pipe Flow. Lecture 17

Pipe Flow. Lecture 17 Pipe Flow Lecture 7 Pipe Flow and the Energy Equation For pipe flow, the Bernoulli equation alone is not sufficient. Friction loss along the pipe, and momentum loss through diameter changes and corners

More information

Two-Fluid Model 41. Simple isothermal two-fluid two-phase models for stratified flow:

Two-Fluid Model 41. Simple isothermal two-fluid two-phase models for stratified flow: Two-Fluid Model 41 If I have seen further it is by standing on the shoulders of giants. Isaac Newton, 1675 3 Two-Fluid Model Simple isothermal two-fluid two-phase models for stratified flow: Mass and momentum

More information

Open Channel Flow - General. Open Channel Flow

Open Channel Flow - General. Open Channel Flow Open Channel Flow - General Hydromechanics VVR090 Open Channel Flow Open channel: a conduit for flow which has a free surface Free surface: interface between two fluids of different density Characteristics

More information

NPTEL Quiz Hydraulics

NPTEL Quiz Hydraulics Introduction NPTEL Quiz Hydraulics 1. An ideal fluid is a. One which obeys Newton s law of viscosity b. Frictionless and incompressible c. Very viscous d. Frictionless and compressible 2. The unit of kinematic

More information

Lesson 37 Transmission Of Air In Air Conditioning Ducts

Lesson 37 Transmission Of Air In Air Conditioning Ducts Lesson 37 Transmission Of Air In Air Conditioning Ducts Version 1 ME, IIT Kharagpur 1 The specific objectives of this chapter are to: 1. Describe an Air Handling Unit (AHU) and its functions (Section 37.1).

More information

1. Open Channel Hydraulics

1. Open Channel Hydraulics Open Channel Flow. Open Channel Hydraulics.... Definition and differences between pipe flow and open channel flow.... Types of flow.... Properties of open channels...4.4 Fundamental equations... 5.4. The

More information

STEADY FLOW THROUGH PIPES DARCY WEISBACH EQUATION FOR FLOW IN PIPES. HAZEN WILLIAM S FORMULA, LOSSES IN PIPELINES, HYDRAULIC GRADE LINES AND ENERGY

STEADY FLOW THROUGH PIPES DARCY WEISBACH EQUATION FOR FLOW IN PIPES. HAZEN WILLIAM S FORMULA, LOSSES IN PIPELINES, HYDRAULIC GRADE LINES AND ENERGY STEADY FLOW THROUGH PIPES DARCY WEISBACH EQUATION FOR FLOW IN PIPES. HAZEN WILLIAM S FORMULA, LOSSES IN PIPELINES, HYDRAULIC GRADE LINES AND ENERGY LINES 1 SIGNIFICANCE OF CONDUITS In considering the convenience

More information

Channel Structure Influence on the Thermal-Hydraulic Performance of. Zigzag PCHE

Channel Structure Influence on the Thermal-Hydraulic Performance of. Zigzag PCHE The 6th International Supercritical CO2 Power Cycles Symposium March 27-29, 218, Pittsburgh, Pennsylvania Channel Structure Inluence on the Thermal-Hydraulic Perormance o Zigzag PCHE Yichao Gao Wenkai

More information

PIPE FLOWS: LECTURE /04/2017. Yesterday, for the example problem Δp = f(v, ρ, μ, L, D) We came up with the non dimensional relation

PIPE FLOWS: LECTURE /04/2017. Yesterday, for the example problem Δp = f(v, ρ, μ, L, D) We came up with the non dimensional relation /04/07 ECTURE 4 PIPE FOWS: Yesterday, for the example problem Δp = f(v, ρ, μ,, ) We came up with the non dimensional relation f (, ) 3 V or, p f(, ) You can plot π versus π with π 3 as a parameter. Or,

More information

R09. d water surface. Prove that the depth of pressure is equal to p +.

R09. d water surface. Prove that the depth of pressure is equal to p +. Code No:A109210105 R09 SET-1 B.Tech II Year - I Semester Examinations, December 2011 FLUID MECHANICS (CIVIL ENGINEERING) Time: 3 hours Max. Marks: 75 Answer any five questions All questions carry equal

More information

Mechanical Engineering Programme of Study

Mechanical Engineering Programme of Study Mechanical Engineering Programme of Study Fluid Mechanics Instructor: Marios M. Fyrillas Email: eng.fm@fit.ac.cy SOLVED EXAMPLES ON VISCOUS FLOW 1. Consider steady, laminar flow between two fixed parallel

More information

7. Basics of Turbulent Flow Figure 1.

7. Basics of Turbulent Flow Figure 1. 1 7. Basics of Turbulent Flow Whether a flow is laminar or turbulent depends of the relative importance of fluid friction (viscosity) and flow inertia. The ratio of inertial to viscous forces is the Reynolds

More information

Controlling the Heat Flux Distribution by Changing the Thickness of Heated Wall

Controlling the Heat Flux Distribution by Changing the Thickness of Heated Wall J. Basic. Appl. Sci. Res., 2(7)7270-7275, 2012 2012, TextRoad Publication ISSN 2090-4304 Journal o Basic and Applied Scientiic Research www.textroad.com Controlling the Heat Flux Distribution by Changing

More information

F L U I D S Y S T E M D Y N A M I C S

F L U I D S Y S T E M D Y N A M I C S F L U I D S Y S T E M D Y N A M I C S T he proper design, construction, operation, and maintenance of fluid systems requires understanding of the principles which govern them. These principles include

More information

s and FE X. A. Flow measurement B. properties C. statics D. impulse, and momentum equations E. Pipe and other internal flow 7% of FE Morning Session I

s and FE X. A. Flow measurement B. properties C. statics D. impulse, and momentum equations E. Pipe and other internal flow 7% of FE Morning Session I Fundamentals of Engineering (FE) Exam General Section Steven Burian Civil & Environmental Engineering October 26, 2010 s and FE X. A. Flow measurement B. properties C. statics D. impulse, and momentum

More information

Fluid Mechanics Prof. S.K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur

Fluid Mechanics Prof. S.K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Fluid Mechanics Prof. S.K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture - 42 Flows with a Free Surface Part II Good morning. I welcome you to this session

More information

Basic Hydraulics June 2007

Basic Hydraulics  June 2007 Basic Hydraulics www.concrete-pipe.org June 2007 2007 Overview Open Channel Flow Manning Equation Basic Culvert Design Sanitary Sewer Design Flow, Velocity Stormwater Sewer Design Flow, Velocity 2 Open

More information