HIGH POWER LED TSLG-WF7060-A07

Transcription

1 HIGH POWER LED High Power LED Features Feature of the device Small package with high efficiency Color coordinates: x=0.33, y=0.33 according to CIE 1931 Typical color temperature: 5600 K View angle: 120 C High luminous flux output: more than 34lm@350mA ESD protection Soldering methods: SMT Grouping parameter Total luminous flux, color coordinates Optical efficiency: 27 lm/w Thermal resistance (junction to lead): 17 K/W RoHS Compliance QSLLGWFU Applications TFT LCD display backlight Decorative and entertainment illumination Signal and symbol luminaries for orientation marker light (e.g. steps, exit ways, etc.) Exterior and interior automotive illumination Materials Items Housing Encapsulating Resin Electrodes Die attach Chip Description Heat resistant polymer Clear silicone resin Ag plating copper alloy Silver paste InGaN TAITRON COMPONENTS INCORPORATED Tel: (800) (800)-TAITRON (661) Fax: (800)-TAITFAX (800) (661) Page 1 of 10

2 Absolute Maximum Ratings (Ta=25 C) Parameter Symbol Value Unit Forward Current IF 500 ma Junction to heat-sink thermal resistance Rth 17 K/W Power Dissipation Pd 2.1 W Junction Temperature Tj 125 C Operating Temperature Topr -40 ~ +100 C Storage Temperature Tstg -40 ~ +100 C Electro-Optical Characteristics (Ta=25 C) Parameter Bin Symbol Min. Typ. Max. Unit Condition J Luminous Flux (1) J2 θv J Im IF =350mA Viewing Angle (2) θ1/ deg Forward Voltage VF V Notes: 1. Luminous flux measurement tolerance: ±10% 2. 2θ1/2 is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value. Page 2 of 10

3 Typical Electro-Optical Characteristics Curves Relative Spectral Distribution, IF=350mA, Ta=25 C Forward Voltage vs Forward Current, Ta=25 C Wavelength λp(nm) Relative Luminous Intensity vs Forward Current, Ta=25 C Forward Current (ma) Forward Current Derating Curve, Derating based on TJMAX=125 C Forward Current (ma) Typical Representative Spatial Radiation Pattern Ambient Temperature Ta ( C) Relative Intensity Relative luminous intensity Forward Current (ma) Relative luminous intensity (%) Forward Voltage (Volt) Angle (Degree) Page 3 of 10

4 Reliability Test Items and Conditions The reliability of products shall be satisfied with items listed below. Confidence level: 90%, LTPD: 10% No. Items Test Condition Test Hours / Cycles Sample Size Ac/Re 1 Solderability Tsol=230 C, 5sec 1 times 11 PCS 0/1 2 Reflow Soldering Tsol =260 C, 10sec 3 Temperature Cycle 4 Thermal Shock H: +100 C 30min 5 min L: -40 C 30min H: +110 C 30min 5 min L: -40 C 30min 6 Min, 3 times 11 PCS 0/ Cycles 11 PCS 0/1 500 Cycles 11 PCS 0/1 5 High Temperature Storage Temp: 110 C 1000 Hrs. 11 PCS. 0/1 6 Low Temperature Storage Temp: -40 C 1000 Hrs. 11 PCS. 0/1 7 High Temperature Operation Life #1 Ta=55 C IF=350mA 1000 Hrs. 11 PCS. 0/1 8 High Temperature Operation Life #2 Ta=85 C IF=350mA 1000 Hrs. 11 PCS. 0/1 9 High Temperature Operation Life #3 Ta=100 C IF=350mA 1000 Hrs. 11 PCS. 0/1 10 Low Temperature Operation Life Ta=-40 C IF=350mA 1000 Hrs. 11 PCS. 0/1 11 Power Temperature Cycle H: +85 C 15min 5 min L: -40 C 15min 1000 cycles 11 PCS. 0/1 12 High Temperature / High Humidity 85 C / 85%RH 1000 Hrs. 11 PCS. 0/1 13 ESD Human Body Model 2000V, Interval: 0.5sec 3 times 11 PCS. 0/1 14 ESD Machine Model 200V, Interval: 0.5sec 3 times 11 PCS. 0/1 Notes: Im: Brightness Attenuate Difference (1000hrs) <10% VF: Forward Voltage Difference < 20% Page 4 of 10

5 Package Dimensions (In mm) Recommended Solder Pad Note: 1. Dimensions are in millimeters 2. Tolerances unless dimensions ± 0.25mm Carrier Tape Dimensions: Loaded quantity 800pcs per reel Note: 1. Dimensions are in millimeters 2. Tolerances unless dimensions ± 0.1mm Page 5 of 10

6 Reel Dimensions: Note: The tolerances unless mentioned is ± 0.1mm, Unit = mm Moisture Resistant Packaging: Page 6 of 10

7 Ordering Information TS L G W F TR70 Lead Free Tape & Reel 7=7 reel 0=3k per reel Factory Location Code Size in mm Flat Top White Color Diffused G-bend Lead Frame Type Taitron SMD LED Color Binning Rank A0 x y Reference CCT: 9000K K Rank B3 x y Reference CCT: 7000K K Rank B4 x y Reference CCT: 6200K K Rank B5 x y Reference CCT: 7000K K Rank B6 x y Reference CCT: 5600K K Rank C0 x y Reference CCT: 4600K K Note: Color coordinates measurement allowance: ± Page 7 of 10

8 Color Binning Structure Graphic Representation Precautions for Use 1. Over-current-proof Though this part has conducted ESD protection mechanism, customer must not use the device in reverse and should apply resistors for extra protection. Otherwise slight voltage shift will cause enormous current change and burn out failure would happen. 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30 C or less and 90% RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, The LEDs should be kept at 30 C or less and 70% RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. 2.7 Pre-curing treatment: 60±5 C for 24 hours. 3. Thermal Management 3.1 Because the part is a high power dissipation device, special and sufficient consideration in thermal management design must be made to optimize the thermal performance. 3.2 Heat sink design is implemented in the device for an additional thermal connection. Since the Page 8 of 10

9 device is capable of SMT process, tin must be spread both heat sink and solder pads areas to dissipate the heat. 3.3 A high thermal conductivity substrate, such as Aluminum or Copper plate etc, must be applied for extermal thermal management. It is strongly recommended that the outer heat sink or PCB dimension per LED can not be less than 25 x 25 x 1 (L x M x H) mm. The materials for outer heat sink can be FR4 on Aluminum, MCPCB, or FPC on Aluminum. 3.4 Special thermal designs are also recommended to take in outer heat sink design, such as FR4 PCB on Aluminum with thermal vias or FRC on Aluminum with thermal conductive adhesive, etc. 3.5 Sufficient thermal management must be conducted, or the die junction temperature will be over the limit under large electronic driving and LED lifetime will decrease critically. 4. Soldering Condition 4.1 Pb-free solder temperature profile. 4.2 Reflow soldering should not be done more than two times. 4.3 When soldering, do not put stress on the LEDs during heating. 4.4 After soldering, do not warp the circuit board. 5. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 C for 3 seconds within. Once in less than the soldering iron capacity 25W, leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 6. Handling Indications During processing, mechanical stress on the surface should be minimized as much as possible. Sharp objects of all types should not be used to pierce the sealing compound. 7. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a Page 9 of 10

10 double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. How to contact us US HEADQUARTERS WEST HARRISON PARKWAY, VALENCIA, CA Tel: (800) TAITRON (800) (661) Fax: (800) TAITFAX (800) (661) TAITRON COMPONENTS MEXICO, S.A.DE C.V. BOULEVARD CENTRAL 5000 INTERIOR 5 PARQUE INDUSTRIAL ATITALAQUIA, HIDALGO C.P MEXICO Tel: Fax: TAITRON COMPONETS INCORPORATED E REPRESENTAÇÕES DO BRASIL LTDA RUA DOMINGOS DE MORAIS, 2777, 2.ANDAR, SALA 24 SAÚDE - SÃO PAULO-SP BRAZIL Tel: Fax: TAITRON COMPONETS INCORPORATED, SHANGHAI REPRESENTATIVE OFFICE CROSS REGION PLAZA, 899 LINGLING ROAD, SUITE 18C, SHANGHAI, , CHINA Tel: Fax: Page 10 of 10