Convection. U y. U u(y) T s. T y

Size: px
Start display at page:

Download "Convection. U y. U u(y) T s. T y"

Transcription

1

2 Convection Heat transfer in the presence of a fluid motion on a solid surface Various mechanisms at play in the fluid: - advection physical transport of the fluid - diffusion conduction in the fluid - generation due to fluid friction But fluid directly in contact with the wall does not move relative to it; hence direct heat transport to the fluid is by conduction in the fluid only. U y U u(y) q y T T(y) q conv T y k f T y y0 h T s T But depends on the whole fluid motion, and both fluid flow y 0 and heat transfer equations are needed T s U y T T(y) T s

3 Convection Convection Free or natural convection (induced by buoyancy forces) forced convection (driven eternally) May occur with phase change (boiling, condensation) Heat transfer rate q = h( T s -T )W h=heat transfer coefficient (W /m 2 K) (h is not a property. It depends on geometry,nature of flow, thermodynamics properties etc.) Typical values of h (W/m 2 K) Free convection: gases: 2-25 liquid: Forced convection: gases: liquid: 50-20,000 Boiling/Condensation: ,000

4 Convection rate equation U y U u(y) q y T T(y) T s Main purpose of convective heat transfer analysis is to determine: flow field temperature field in fluid heat transfer coefficient, h q =heat flu = h(t s -T ) q = -k(t/ y) y=0 Hence, h = [-k(t/ y) y=0 ] / (T s -T ) The epression shows that in order to determine h, we must first determine the temperature distribution in the thin fluid layer that coats the wall.

5 Classes of convective flows: etremely diverse several parameters involved (fluid properties, geometry, nature of flow, phases etc) systematic approach required classify flows into certain types, based on certain parameters identify parameters governing the flow, and group them into meaningful non-dimensional numbers need to understand the physics behind each phenomenon Common classifications: A. Based on geometry: Eternal flow / Internal flow B. Based on driving mechanism Natural convection / forced convection / mied convection C. Based on number of phases Single phase / multiple phase D. Based on nature of flow Laminar / turbulent

6 How to solve a convection problem? Solve governing equations along with boundary conditions Governing equations include 1. conservation of mass 2. conservation of momentum 3. conservation of energy In Conduction problems, only (3) is needed to be solved. Hence, only few parameters are involved In Convection, all the governing equations need to be solved. large number of parameters can be involved

7 Forced convection: Non-dimensional groupings Nusselt No. Nu = h / k = (convection heat transfer strength)/ (conduction heat transfer strength) Prandtl No. Pr = / = (momentum diffusivity)/ (thermal diffusivity) Reynolds No. Re = U / = (inertia force)/(viscous force) Viscous force provides the dampening effect for disturbances in the fluid. If dampening is strong enough laminar flow Otherwise, instability turbulent flow critical Reynolds number Laminar Turbulent

8 FORCED CONVECTION: eternal flow (over flat plate) An internal flow is surrounded by solid boundaries that can restrict the development of its boundary layer, for eample, a pipe flow. An eternal flow, on the other hand, are flows over bodies immersed in an unbounded fluid so that the flow boundary layer can grow freely in one direction. Eamples include the flows over airfoils, ship hulls, turbine blades, etc. Fluid particle adjacent to the solid surface is at rest T Ts These particles act to retard the motion of adjoining layers q boundary layer effect Momentum balance: inertia forces, pressure gradient, viscous forces, body forces Energy balance: convective flu, diffusive flu, heat generation, energy storage h=f(fluid, Vel,Distance,Temp)

9 Hydrodynamic boundary layer One of the most important concepts in understanding the eternal flows is the boundary layer development. For simplicity, we are going to analyze a boundary layer flow over a flat plate with no curvature and no eternal pressure variation. U U U U Dye streak laminar transition turbulent Boundary layer definition Boundary layer thickness (): defined as the distance away from the surface where the local velocity reaches to 99% of the free-stream velocity, that is u(y=)=0.99u. Somewhat an easy to understand but arbitrary definition. Boundary layer is usually very thin: / usually << 1.

10 Hydrodynamic and Thermal boundary layers As we have seen earlier,the hydrodynamic boundary layer is a region of a fluid flow, near a solid surface, where the flow patterns are directly influenced by viscous drag from the surface wall. 0<u<U, 0<y< The Thermal Boundary Layer is a region of a fluid flow, near a solid surface, where the fluid temperatures are directly influenced by heating or cooling from the surface wall. 0<t<T, 0<y< t The two boundary layers may be epected to have similar characteristics but do not normally coincide. Liquid metals tend to conduct heat from the wall easily and temperature changes are observed well outside the dynamic boundary layer. Other materials tend to show velocity changes well outside the thermal layer.

11 Effects of Prandtl number, Pr T, T T Pr >>1 >> e.g., oils Pr = 1 = e.g., air and gases have Pr ~ 1 u U ( ) T similar to T T T W (Reynold s analogy) W Pr <<1 << e.g., liquid metals

12 Boundary layer equations (laminar flow) Simpler than general equations because boundary layer is thin T U y T W U Equations for 2D, laminar, steady boundary layer flow Conservation of Conservation of mass: u v y - momentum: 0 u u u v y U T T T Conservation of energy: u v y y y du Note: for a flat plate, U is constant, hence 0 d du d T y u y

13 Eact solutions: Blasius Pr Re number Nusselt Average Pr Re number Nusselt Local Re Re coefficien t drag Average, Re Re coefficien t friction Skin Re 4.99 Boundary layer thickness L L L L f D y w w f Nu Nu L U d C L C y u U U C

14 Heat transfer coefficient Local heat transfer coefficient: h Nu k 0.339k Re 1 2 Pr 1 3 Average heat transfer coefficient: h Nu L k 0.678k Re L Recall: qw h A Tw T, heat flow rate from wall w w 1 2 L Pr 1 3 Film temperature, T film For heated or cooled surfaces, the thermophysical properties within the boundary layer should be selected based on the average 1 temperature of the wall and the free stream; T film T w T 2

15 Heat transfer coefficient Convection Coefficient, h. Thermal Boundary Layer, t U Hydrodynamic Boundary Layer, Laminar and turbulent b.l. Laminar Region Turbulent Region

16 * Re more * * (Re U Re c * Turbulent C C Re Re Re Re Re Calculate Turbulent boundary layer ), the b.l. equations difficult to solve. flow becomes (For flow over flat plate, We will mainly use correlatio ns based on eperiment al data : f D Nu Nu increases c c with. 0.2 L L 1 Re Pr Pr 1 3 L 1 3 (Re Beyond Re Pr are similar to 1 3 a 510 critical Re transitio nal 0.8 c Re heat trans fer coefficien t in usual way : h 5 ) 0.8 c value c of and 510 laminar ones, 0.5 c Re Reynolds eventually c ) number turbulent. but infinitely Nu k etc.

17 Laminar Boundary Layer Development 1 ( ) 0.5 Boundary layer growth: Initial growth is fast Growth rate d/d 1/, decreasing downstream w ( ) 10 5 Wall shear stress: w 1/ As the boundary layer grows, the wall shear stress decreases as the velocity gradient at the wall becomes less steep

18 Eample Determine the boundary layer thickness, the wall shear stress of a laminar water flow over a flat plate. The free stream velocity is 1 m/s, the kinematic viscosity of the water is 10-6 m 2 /s. The density of the water is 1,000 kg/m 3. The transition Reynolds number Re=U/= Determine the distance downstream of the leading edge when the boundary transitions to turbulent. Determine the total frictional drag produced by the laminar and turbulent portions of the plate which is 1 m long. If the free stream and plate temperatures are 100 C and 25 C, respectively, determine the heat transfer rate from the plate. m 3 ( ) ( ). U Therefore, for a 1m long plate, the boundary layer grows by 0.005(m), or 5 mm, a very thin layer. U U The wall shear stress, ( Pa) w U Re U tr 5 The transition Reynolds number: Re 5 10, tr 0.5( m)

19 Eample (cont..) The total frictional drag is equal to the integration of the wall shear stress: tr tr 2 U 0.664U F D w (1) d 0.332U d 0.939( N ) Re 0 0 Define skin friction coefficient: C C f w 1 2 U Re for a f laminar boundary layer. tr

20 Forced convection over eterior bodies Much more complicated. Some boundary layer may eist, but it is likely to be curved and U will not be constant. Boundary layer may also separate from the wall. Correlations based on eperimental data can be used for flow and heat transfer calculations Reynolds number should now be based on a characteristic diameter. If body is not circular, the equivalent diameter Dh is used C D Drag U D h force A normal 4 Area Perimeter ; N u h D k Re D ; U D N uk h D

21 Flow over circular cylinders Nu Re D C Re m D 5 6 Pr Pr C s m All properties at free stream temperature, Pr s at cylinder surface temperature

22 FORCED CONVECTION: Internal flow Thermal conditions Laminar or turbulent entrance flow and fully developed thermal condition e.g. pipe flow Thermal entrance region, fd,t For laminar flows the thermal entrance length is a function of the Reynolds number and the Prandtl number: fd,t /D 0.05Re D Pr, where the Prandtl number is defined as Pr = / and is the thermal diffusitivity. For turbulent flow, fd,t 10D.

23 Thermal Conditions For a fully developed pipe flow, the convection coefficient does not vary along the pipe length. (provided all thermal and flow properties are constant) h() constant fd,t Newton s law of cooling: q S = ha(t S -T m ) Question: since the temperature inside a pipe flow does not remain constant, we should use a mean temperature T m, which is defines as follows:

24 Energy Transfer Consider the total thermal energy carried by the fluid as A VC TdA v (mass flu) (internal energy) Now imagine this same amount of energy is carried by a body of fluid with the same mass flow rate but at a uniform mean temperature T m. Therefore T m can be defined as VCvTdA A Tm mc & v Consider T m as the reference temperature of the fluid so that the total heat transfer between the pipe and the fluid is governed by the Newton s cooling law as: q s =h(t s -T m ), where h is the local convection coefficient, and T s is the local surface temperature. Note: usually T m is not a constant and it varies along the pipe depending on the condition of the heat transfer.

25 Energy Balance Eample: We would like to design a solar water heater that can heat up the water temperature from 20 C to 50 C at a water flow rate of 0.15 kg/s. The water is flowing through a 0.05 m diameter pipe and is receiving a net solar radiation flu of 200 W/m of pipe length. Determine the total pipe length required to achieve the goal.

26 Eample (cont.) Questions: (1) How to determine the heat transfer coefficient, h? There are a total of si parameters involved in this problem: h, V, D,, k f, c p. The temperature dependence of properties is implicit and is only through the variation of thermal properties. Density is included in the kinematic viscosity,. According to the Buckingham theorem, it is possible for us to reduce the number of parameters by three. Therefore, the convection coefficient relationship can be reduced to a function of only three variables: Nu=hD/k f, Nusselt number, Re=VD/, Reynolds number, and Pr=, Prandtl number. This conclusion is consistent with empirical observation, that is Nu=f(Re, Pr). If we can determine the Reynolds and the Prandtl numbers, we can find the Nusselt number and hence, the heat transfer coefficient, h.

27 D Convection Correlations Laminar, fully developed circular pipe flow: hd Nu D 4.36, when q s" constant, (page 543, ch. 10-6, ITHT) k f Nu 3.66, when T constant, (page 543, ch. 10-6, ITHT) Note: the therma conductivity should be calculated at T. s m Fully developed, turbulent pipe flow: Nu f(re, Pr), Nu can be related to Re & Pr eperimentally, as shown. Fied Pr Fied Re ln(nu) slope m ln(nu) slope n ln(re) ln(pr)

28 Empirical Correlations 4/5 n Dittus-Boelter equation: NuD 0.023Re Pr, (eq 10-76, p 546, ITHT) where n 0.4 for heating (T st m), n 0.3 for cooling (Ts T m). The range of validity: 0.7 Pr 160, ReD 10,000, L/ D 10. Note: This equation can be used only for moderate temperature difference with all the properties evaluated at T m. Other more accurate correlation equations can be found in other references. Caution: The ranges of application for these correlations can be quite different. ( / 8)(Re 1000) Pr Nu f D D (from other reference) 1/2 2/ ( f / 8) (Pr 1) It is valid for 0.5 Pr 2000 and 3000 Re 5 10 All properties are calculated at T. m D 6.

29 Eample (cont.) In our eample, we need to first calculate the Reynolds number: water at 35 C, Cp=4.18(kJ/kg.K), =710-4 (N.s/m 2 ), k f =0.626 (W/m.K), Pr=4.8. m& VD D 4 4(0.15) Re A m& D (0.05)(7 10 ) Re 4000, it is turbulent pipe flow. Use the Gnielinski correlation, from the Moody chart, f 0.036, Pr 4.8 Nu ( f / 8)(Re 1000) Pr ( / 8)( )(4.8) 1/2 2/ ( f / 8) (Pr 1) (0.036 / 8) (4.8 1) D D 1/2 2/3 k f h NuD W m K D (37.4) 469( / 2. ) 37.4

30 Energy Balance Question (2): How can we determine the required pipe length? Use energy balance concept: (energy storage) = (energy in) minus (energy out). energy in = energy received during a steady state operation (assume no loss) q'( L) mc & ( T T ), L P out in mc & P ( Tin Tout ) (0.15)(4180)(50 20) q ' ( m) q =q/l T in T out

31 s Temperature Distribution Question (3): Can we determine the water temperature variation along the pipe? Recognize the fact that the energy balance equation is valid for any pipe length : q'( ) mc & ( T( ) T ) P q ' 200 T( ) Tin mc & (0.15)(4180) It is a linear distribution along the pipe Question (4): How about the surface temperature distribution? From local Newton's cooling law: q ha(t T ) q' h( D)(T ( ) T ( )) m P q ' 200 Ts( ) Tm( ) ( C) Dh (0.05)(469) At the end of the pipe, T ( 94) 52.7( C) in s s m

32 Temperature variation for constant heat flu 60 T m ( ) T s ( ) Constant temperature difference due to the constant heat flu Note: These distributions are valid only in the fully developed region. In the entrance region, the convection condition should be different. In general, the entrance length /D10 for a turbulent pipe flow and is usually negligible as compared to the total pipe length.

33 Internal Flow Convection -constant surface temperature case Another commonly encountered internal convection condition is when the surface temperature of the pipe is a constant. The temperature distribution in this case is drastically different from that of a constant heat flu case. Consider the following pipe flow configuration: T m,i d Constant T s T m,o T m T m +dt m Energy change mc & [( T dt ) T ] mc & p dt m Energy in ha(t T ) s p m m m m q s =ha(t s -T m ) Energy change energy in mc & dt ha(t T ) p m s m

34 Temperature distribution mc & dt ha(t T ), m p m s s Note: q ha(t T ) is valid locally only, since T is not a constant dtm (T T ) s ha mc & P m m, where A Pd, and P is the perimeter of the pipe Integrate from the inlet to a diatance downstream: Tm ( ) m T mi, dt hp P d (T T ) mc & mc & m T 0 0 s P P Ph Tm ( ) ln(t m s) T, where L is the total pipe length mi, mc & P and h is the averaged convection coefficient of the pipe between 0 &. 1 h hd, or hd 0 h 0 hd m

35 Temperature distribution Tm( ) Ts Ph ep( ), for constant surface temperature T T mc & mi, s P Constant surface temperature T s T( ) T m () The difference between the averaged fluid temperature and the surface temperature decreases eponentially further downstream along the pipe.

36 Log-Mean Temperature Difference For the entire pipe: Tmo, Ts To h( PL) has ep( ) or mc & P T T mi, Ts Ti mc & P o ln( ) T q mc & ( T T ) mc & (( T T ) ( T T )) P m, o m, i P s m, i s m, o To Ti mc & ( T T ) ha ha T To ln( ) T P i o s s lm i To Ti where Tlm is called the log mean temperature difference. To ln( ) T This relation is valid for the entire pipe. i i

37 Free Convection A free convection flow field is a self-sustained flow driven by the presence of a temperature gradient. (As opposed to a forced convection flow where eternal means are used to provide the flow.) As a result of the temperature difference, the density field is not uniform also. Buoyancy will induce a flow current due to the gravitational field and the variation in the density field. In general, a free convection heat transfer is usually much smaller compared to a forced convection heat transfer. It is therefore important only when there is no eternal flow eists. T cold hot Flow is unstable and a circulatory pattern will be induced.

38 Basic Definitions Buoyancy effect: Surrounding fluid, cold, Hot plate Warm, Net force=( - gv The density difference is due to the temperature difference and it can be characterized by ther volumetric thermal epansion coefficient, : ( ) P T T T T T

39 Grashof Number and Rayleigh Number Define Grashof number, Gr, as the ratio between the buoyancy force and the viscous force: 3 Gr gtl g ( T T ) L 3 S 2 2 Grashof number replaces the Reynolds number in the convection correlation equation. In free convection, buoyancy driven flow sometimes dominates the flow inertia, therefore, the Nusselt number is a function of the Grashof number and the Prandtle number alone. Nu=f(Gr, Pr). Reynolds number will be important if there is an eternal flow. (combined forced and free convection. In many instances, it is better to combine the Grashof number and the Prandtle number to define a new parameter, the Rayleigh number, Ra=GrPr. The most important use of the Rayleigh number is to characterize the laminar to turbulence transition of a free convection boundary layer flow. For eample, when Ra>10 9, the vertical free convection boundary layer flow over a flat plate becomes turbulent.

40 Eample Determine the rate of heat loss from a heated pipe as a result of natural (free) convection. T =0 C D=0.1 m Ra Nu T s =100C Film temperature( T f ): averaged boundary layer temperature T f =1/2(T s +T )=50 C. k f =0.03 W/m.K, Pr=0.7, =210-5 m 2 /s, =1/T f =1/(273+50)=0.0031(1/K) g ( TS T ) L (9.8)(0.0031)(100 0)(0.1) (2 10 ) D Pr (0.7) Ra [1 (0.559 / Pr) ] 1/6 {0.6 2 } 9 /16 8 / (equation in Table 11.1) k f 0.03 (26) 7.8( / 2 h NuD W m K ) D 0.1 q ha( T T ) (7.8)( )( 0.1)(1)(100 0) 244.9( W ) S Can be significant if the pipe are long.

MYcsvtu Notes HEAT TRANSFER BY CONVECTION

MYcsvtu Notes HEAT TRANSFER BY CONVECTION www.mycsvtunotes.in HEAT TRANSFER BY CONVECTION CONDUCTION Mechanism of heat transfer through a solid or fluid in the absence any fluid motion. CONVECTION Mechanism of heat transfer through a fluid in

More information

UNIT II CONVECTION HEAT TRANSFER

UNIT II CONVECTION HEAT TRANSFER UNIT II CONVECTION HEAT TRANSFER Convection is the mode of heat transfer between a surface and a fluid moving over it. The energy transfer in convection is predominately due to the bulk motion of the fluid

More information

Introduction to Heat and Mass Transfer. Week 14

Introduction to Heat and Mass Transfer. Week 14 Introduction to Heat and Mass Transfer Week 14 Next Topic Internal Flow» Velocity Boundary Layer Development» Thermal Boundary Layer Development» Energy Balance Velocity Boundary Layer Development Velocity

More information

Convection Heat Transfer. Introduction

Convection Heat Transfer. Introduction Convection Heat Transfer Reading Problems 12-1 12-8 12-40, 12-49, 12-68, 12-70, 12-87, 12-98 13-1 13-6 13-39, 13-47, 13-59 14-1 14-4 14-18, 14-24, 14-45, 14-82 Introduction Newton s Law of Cooling Controlling

More information

Convection. forced convection when the flow is caused by external means, such as by a fan, a pump, or atmospheric winds.

Convection. forced convection when the flow is caused by external means, such as by a fan, a pump, or atmospheric winds. Convection The convection heat transfer mode is comprised of two mechanisms. In addition to energy transfer due to random molecular motion (diffusion), energy is also transferred by the bulk, or macroscopic,

More information

External Flows. Dye streak. turbulent. laminar transition

External Flows. Dye streak. turbulent. laminar transition Eternal Flos An internal flo is surrounded by solid boundaries that can restrict the development of its boundary layer, for eample, a pipe flo. An eternal flo, on the other hand, are flos over bodies immersed

More information

Convection Workshop. Academic Resource Center

Convection Workshop. Academic Resource Center Convection Workshop Academic Resource Center Presentation Outline Understanding the concepts Correlations External Convection (Chapter 7) Internal Convection (Chapter 8) Free Convection (Chapter 9) Solving

More information

Heat Transfer Convection

Heat Transfer Convection Heat ransfer Convection Previous lectures conduction: heat transfer without fluid motion oday (textbook nearly 00 pages) Convection: heat transfer with fluid motion Research methods different Natural Convection

More information

CHAPTER 4 BOUNDARY LAYER FLOW APPLICATION TO EXTERNAL FLOW

CHAPTER 4 BOUNDARY LAYER FLOW APPLICATION TO EXTERNAL FLOW CHAPTER 4 BOUNDARY LAYER FLOW APPLICATION TO EXTERNAL FLOW 4.1 Introduction Boundary layer concept (Prandtl 1904): Eliminate selected terms in the governing equations Two key questions (1) What are the

More information

Introduction to Heat and Mass Transfer. Week 14

Introduction to Heat and Mass Transfer. Week 14 Introduction to Heat and Mass Transfer Week 14 HW # 7 prob. 2 Hot water at 50C flows through a steel pipe (thermal conductivity 14 W/m-K) of 100 mm outside diameter and 8 mm wall thickness. During winter,

More information

Principles of Convection

Principles of Convection Principles of Convection Point Conduction & convection are similar both require the presence of a material medium. But convection requires the presence of fluid motion. Heat transfer through the: Solid

More information

Chapter 3 NATURAL CONVECTION

Chapter 3 NATURAL CONVECTION Fundamentals of Thermal-Fluid Sciences, 3rd Edition Yunus A. Cengel, Robert H. Turner, John M. Cimbala McGraw-Hill, 2008 Chapter 3 NATURAL CONVECTION Mehmet Kanoglu Copyright The McGraw-Hill Companies,

More information

HEAT TRANSFER BY CONVECTION. Dr. Şaziye Balku 1

HEAT TRANSFER BY CONVECTION. Dr. Şaziye Balku 1 HEAT TRANSFER BY CONVECTION Dr. Şaziye Balku 1 CONDUCTION Mechanism of heat transfer through a solid or fluid in the absence any fluid motion. CONVECTION Mechanism of heat transfer through a fluid in the

More information

PHYSICAL MECHANISM OF NATURAL CONVECTION

PHYSICAL MECHANISM OF NATURAL CONVECTION 1 NATURAL CONVECTION In this chapter, we consider natural convection, where any fluid motion occurs by natural means such as buoyancy. The fluid motion in forced convection is quite noticeable, since a

More information

Empirical Co - Relations approach for solving problems of convection 10:06:43

Empirical Co - Relations approach for solving problems of convection 10:06:43 Empirical Co - Relations approach for solving problems of convection 10:06:43 10:06:44 Empirical Corelations for Free Convection Use T f or T b for getting various properties like Re = VL c / ν β = thermal

More information

PHYSICAL MECHANISM OF CONVECTION

PHYSICAL MECHANISM OF CONVECTION Tue 8:54:24 AM Slide Nr. 0 of 33 Slides PHYSICAL MECHANISM OF CONVECTION Heat transfer through a fluid is by convection in the presence of bulk fluid motion and by conduction in the absence of it. Chapter

More information

CHME 302 CHEMICAL ENGINEERING LABOATORY-I EXPERIMENT 302-V FREE AND FORCED CONVECTION

CHME 302 CHEMICAL ENGINEERING LABOATORY-I EXPERIMENT 302-V FREE AND FORCED CONVECTION CHME 302 CHEMICAL ENGINEERING LABOATORY-I EXPERIMENT 302-V FREE AND FORCED CONVECTION OBJECTIVE The objective of the experiment is to compare the heat transfer characteristics of free and forced convection.

More information

Summary of Dimensionless Numbers of Fluid Mechanics and Heat Transfer

Summary of Dimensionless Numbers of Fluid Mechanics and Heat Transfer 1. Nusselt number Summary of Dimensionless Numbers of Fluid Mechanics and Heat Transfer Average Nusselt number: convective heat transfer Nu L = conductive heat transfer = hl where L is the characteristic

More information

Chapter 9 NATURAL CONVECTION

Chapter 9 NATURAL CONVECTION Heat and Mass Transfer: Fundamentals & Applications Fourth Edition in SI Units Yunus A. Cengel, Afshin J. Ghajar McGraw-Hill, 2011 Chapter 9 NATURAL CONVECTION PM Dr Mazlan Abdul Wahid Universiti Teknologi

More information

Problem 4.3. Problem 4.4

Problem 4.3. Problem 4.4 Problem 4.3 Problem 4.4 Problem 4.5 Problem 4.6 Problem 4.7 This is forced convection flow over a streamlined body. Viscous (velocity) boundary layer approximations can be made if the Reynolds number Re

More information

Chapter 7: Natural Convection

Chapter 7: Natural Convection 7-1 Introduction 7- The Grashof Number 7-3 Natural Convection over Surfaces 7-4 Natural Convection Inside Enclosures 7-5 Similarity Solution 7-6 Integral Method 7-7 Combined Natural and Forced Convection

More information

ENGR Heat Transfer II

ENGR Heat Transfer II ENGR 7901 - Heat Transfer II Convective Heat Transfer 1 Introduction In this portion of the course we will examine convection heat transfer principles. We are now interested in how to predict the value

More information

ELEC9712 High Voltage Systems. 1.2 Heat transfer from electrical equipment

ELEC9712 High Voltage Systems. 1.2 Heat transfer from electrical equipment ELEC9712 High Voltage Systems 1.2 Heat transfer from electrical equipment The basic equation governing heat transfer in an item of electrical equipment is the following incremental balance equation, with

More information

FORMULA SHEET. General formulas:

FORMULA SHEET. General formulas: FORMULA SHEET You may use this formula sheet during the Advanced Transport Phenomena course and it should contain all formulas you need during this course. Note that the weeks are numbered from 1.1 to

More information

Forced Convection: Inside Pipe HANNA ILYANI ZULHAIMI

Forced Convection: Inside Pipe HANNA ILYANI ZULHAIMI + Forced Convection: Inside Pipe HANNA ILYANI ZULHAIMI + OUTLINE u Introduction and Dimensionless Numbers u Heat Transfer Coefficient for Laminar Flow inside a Pipe u Heat Transfer Coefficient for Turbulent

More information

Lecture 30 Review of Fluid Flow and Heat Transfer

Lecture 30 Review of Fluid Flow and Heat Transfer Objectives In this lecture you will learn the following We shall summarise the principles used in fluid mechanics and heat transfer. It is assumed that the student has already been exposed to courses in

More information

Convective Mass Transfer

Convective Mass Transfer Convective Mass Transfer Definition of convective mass transfer: The transport of material between a boundary surface and a moving fluid or between two immiscible moving fluids separated by a mobile interface

More information

6.2 Governing Equations for Natural Convection

6.2 Governing Equations for Natural Convection 6. Governing Equations for Natural Convection 6..1 Generalized Governing Equations The governing equations for natural convection are special cases of the generalized governing equations that were discussed

More information

Introduction to Heat and Mass Transfer. Week 12

Introduction to Heat and Mass Transfer. Week 12 Introduction to Heat and Mass Transfer Week 12 Next Topic Convective Heat Transfer» Heat and Mass Transfer Analogy» Evaporative Cooling» Types of Flows Heat and Mass Transfer Analogy Equations governing

More information

Advanced Heat and Mass Transfer by Amir Faghri, Yuwen Zhang, and John R. Howell

Advanced Heat and Mass Transfer by Amir Faghri, Yuwen Zhang, and John R. Howell Laminar external natural convection on vertical and horizontal flat plates, over horizontal and vertical cylinders and sphere, as well as plumes, wakes and other types of free flow will be discussed in

More information

Mechanical Engineering. Postal Correspondence Course HEAT TRANSFER. GATE, IES & PSUs

Mechanical Engineering. Postal Correspondence Course HEAT TRANSFER. GATE, IES & PSUs Heat Transfer-ME GATE, IES, PSU 1 SAMPLE STUDY MATERIAL Mechanical Engineering ME Postal Correspondence Course HEAT TRANSFER GATE, IES & PSUs Heat Transfer-ME GATE, IES, PSU 2 C O N T E N T 1. INTRODUCTION

More information

Chapter 6 Laminar External Flow

Chapter 6 Laminar External Flow Chapter 6 aminar Eternal Flow Contents 1 Thermal Boundary ayer 1 2 Scale analysis 2 2.1 Case 1: δ t > δ (Thermal B.. is larger than the velocity B..) 3 2.2 Case 2: δ t < δ (Thermal B.. is smaller than

More information

Heat and Mass Transfer Unit-1 Conduction

Heat and Mass Transfer Unit-1 Conduction 1. State Fourier s Law of conduction. Heat and Mass Transfer Unit-1 Conduction Part-A The rate of heat conduction is proportional to the area measured normal to the direction of heat flow and to the temperature

More information

Fundamental Concepts of Convection : Flow and Thermal Considerations. Chapter Six and Appendix D Sections 6.1 through 6.8 and D.1 through D.

Fundamental Concepts of Convection : Flow and Thermal Considerations. Chapter Six and Appendix D Sections 6.1 through 6.8 and D.1 through D. Fundamental Concepts of Convection : Flow and Thermal Considerations Chapter Six and Appendix D Sections 6.1 through 6.8 and D.1 through D.3 6.1 Boundary Layers: Physical Features Velocity Boundary Layer

More information

Outlines. simple relations of fluid dynamics Boundary layer analysis. Important for basic understanding of convection heat transfer

Outlines. simple relations of fluid dynamics Boundary layer analysis. Important for basic understanding of convection heat transfer Forced Convection Outlines To examine the methods of calculating convection heat transfer (particularly, the ways of predicting the value of convection heat transfer coefficient, h) Convection heat transfer

More information

PROBLEM 7.2 1/3. (b) The local convection coefficient, Eq. 7.23, and heat flux at x = L are 1/2 1/3

PROBLEM 7.2 1/3. (b) The local convection coefficient, Eq. 7.23, and heat flux at x = L are 1/2 1/3 PROBLEM 7. KNOWN: Temperature and velocity of engine oil. Temperature and length of flat plate. FIND: (a) Velocity and thermal boundary layer thickness at trailing edge, (b) Heat flux and surface shear

More information

ENGR Heat Transfer II

ENGR Heat Transfer II ENGR 7901 - Heat Transfer II External Flows 1 Introduction In this chapter we will consider several fundamental flows, namely: the flat plate, the cylinder, the sphere, several other body shapes, and banks

More information

MECHANISM BEHIND FREE /NATURAL CONVECTION

MECHANISM BEHIND FREE /NATURAL CONVECTION CONVECTIVE HEAT TRANSFER By: Prof K. M. Joshi, Assi. Professor, MED, SSAS Institute of Technology, Surat. MECHANISM BEHIND FREE /NATURAL CONVECTION The stagnate layer of fluid in immediate vicinity of

More information

INSTRUCTOR: PM DR MAZLAN ABDUL WAHID

INSTRUCTOR: PM DR MAZLAN ABDUL WAHID SMJ 4463: HEAT TRANSFER INSTRUCTOR: PM ABDUL WAHID http://www.fkm.utm.my/~mazlan TEXT: Introduction to Heat Transfer by Incropera, DeWitt, Bergman, Lavine 5 th Edition, John Wiley and Sons Chapter 9 Natural

More information

Chapter 10: Boiling and Condensation 1. Based on lecture by Yoav Peles, Mech. Aero. Nuc. Eng., RPI.

Chapter 10: Boiling and Condensation 1. Based on lecture by Yoav Peles, Mech. Aero. Nuc. Eng., RPI. Chapter 10: Boiling and Condensation 1 1 Based on lecture by Yoav Peles, Mech. Aero. Nuc. Eng., RPI. Objectives When you finish studying this chapter, you should be able to: Differentiate between evaporation

More information

Internal Flow: Heat Transfer in Pipes

Internal Flow: Heat Transfer in Pipes Internal Flow: Heat Transfer in Pipes V.Vuorinen Aalto University School of Engineering Heat and Mass Transfer Course, Autumn 2016 November 15 th 2016, Otaniemi ville.vuorinen@aalto.fi First about the

More information

ME 331 Homework Assignment #6

ME 331 Homework Assignment #6 ME 33 Homework Assignment #6 Problem Statement: ater at 30 o C flows through a long.85 cm diameter tube at a mass flow rate of 0.020 kg/s. Find: The mean velocity (u m ), maximum velocity (u MAX ), and

More information

CONVECTIVE HEAT TRANSFER

CONVECTIVE HEAT TRANSFER CONVECTIVE HEAT TRANSFER Mohammad Goharkhah Department of Mechanical Engineering, Sahand Unversity of Technology, Tabriz, Iran CHAPTER 4 HEAT TRANSFER IN CHANNEL FLOW BASIC CONCEPTS BASIC CONCEPTS Laminar

More information

Tutorial 1. Where Nu=(hl/k); Reynolds number Re=(Vlρ/µ) and Prandtl number Pr=(µCp/k)

Tutorial 1. Where Nu=(hl/k); Reynolds number Re=(Vlρ/µ) and Prandtl number Pr=(µCp/k) Tutorial 1 1. Explain in detail the mechanism of forced convection. Show by dimensional analysis (Rayleigh method) that data for forced convection may be correlated by an equation of the form Nu = φ (Re,

More information

C ONTENTS CHAPTER TWO HEAT CONDUCTION EQUATION 61 CHAPTER ONE BASICS OF HEAT TRANSFER 1 CHAPTER THREE STEADY HEAT CONDUCTION 127

C ONTENTS CHAPTER TWO HEAT CONDUCTION EQUATION 61 CHAPTER ONE BASICS OF HEAT TRANSFER 1 CHAPTER THREE STEADY HEAT CONDUCTION 127 C ONTENTS Preface xviii Nomenclature xxvi CHAPTER ONE BASICS OF HEAT TRANSFER 1 1-1 Thermodynamics and Heat Transfer 2 Application Areas of Heat Transfer 3 Historical Background 3 1-2 Engineering Heat

More information

Heat and Mass Transfer Prof. S.P. Sukhatme Department of Mechanical Engineering Indian Institute of Technology, Bombay

Heat and Mass Transfer Prof. S.P. Sukhatme Department of Mechanical Engineering Indian Institute of Technology, Bombay Heat and Mass Transfer Prof. S.P. Sukhatme Department of Mechanical Engineering Indian Institute of Technology, Bombay Lecture No. 18 Forced Convection-1 Welcome. We now begin our study of forced convection

More information

Internal Forced Convection. Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display.

Internal Forced Convection. Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display. Internal Forced Convection Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display. Introduction Pipe circular cross section. Duct noncircular cross section. Tubes small-diameter

More information

PROBLEM 8.3 ( ) p = kg m 1m s m 1000 m = kg s m = bar < P = N m 0.25 m 4 1m s = 1418 N m s = 1.

PROBLEM 8.3 ( ) p = kg m 1m s m 1000 m = kg s m = bar < P = N m 0.25 m 4 1m s = 1418 N m s = 1. PROBLEM 8.3 KNOWN: Temperature and velocity of water flow in a pipe of prescribed dimensions. FIND: Pressure drop and pump power requirement for (a) a smooth pipe, (b) a cast iron pipe with a clean surface,

More information

ENG Heat Transfer II 1. 1 Forced Convection: External Flows Flow Over Flat Surfaces... 4

ENG Heat Transfer II 1. 1 Forced Convection: External Flows Flow Over Flat Surfaces... 4 ENG7901 - Heat Transfer II 1 Contents 1 Forced Convection: External Flows 4 1.1 Flow Over Flat Surfaces............................. 4 1.1.1 Non-Dimensional form of the Equations of Motion.......... 4

More information

External Forced Convection :

External Forced Convection : External Forced Convection : Flow over Bluff Objects (Cylinders, Spheres, Packed Beds) and Impinging Jets Chapter 7 Sections 7.4 through 7.8 7.4 The Cylinder in Cross Flow Conditions depend on special

More information

Fluid Mechanics Prof. T.I. Eldho Department of Civil Engineering Indian Institute of Technology, Bombay. Lecture - 17 Laminar and Turbulent flows

Fluid Mechanics Prof. T.I. Eldho Department of Civil Engineering Indian Institute of Technology, Bombay. Lecture - 17 Laminar and Turbulent flows Fluid Mechanics Prof. T.I. Eldho Department of Civil Engineering Indian Institute of Technology, Bombay Lecture - 17 Laminar and Turbulent flows Welcome back to the video course on fluid mechanics. In

More information

UNIT IV BOUNDARY LAYER AND FLOW THROUGH PIPES Definition of boundary layer Thickness and classification Displacement and momentum thickness Development of laminar and turbulent flows in circular pipes

More information

TankExampleNov2016. Table of contents. Layout

TankExampleNov2016. Table of contents. Layout Table of contents Task... 2 Calculation of heat loss of storage tanks... 3 Properties ambient air Properties of air... 7 Heat transfer outside, roof Heat transfer in flow past a plane wall... 8 Properties

More information

OUTCOME 2 - TUTORIAL 1

OUTCOME 2 - TUTORIAL 1 Unit 4: Heat Transfer and Combustion Unit code: K/60/44 QCF level: 5 Credit value: 5 OUTCOME - TUTORIAL Heat transfer coefficients Dimensional analysis: dimensionless groups; Reynolds, Nusselt, Prandtl,

More information

Fluid Mechanics. Chapter 9 Surface Resistance. Dr. Amer Khalil Ababneh

Fluid Mechanics. Chapter 9 Surface Resistance. Dr. Amer Khalil Ababneh Fluid Mechanics Chapter 9 Surface Resistance Dr. Amer Khalil Ababneh Wind tunnel used for testing flow over models. Introduction Resistances exerted by surfaces are a result of viscous stresses which create

More information

Natural Convection Systems

Natural Convection Systems C H A P T E R 6 Natural Convection Systems 6.1 Physical Mechanism Of Natural Convection Many familiar heat transfer applications involve natural convection as the primary mechanism of heat transfer. Some

More information

Name: ME 315: Heat and Mass Transfer Spring 2008 EXAM 2 Tuesday, 18 March :00 to 8:00 PM

Name: ME 315: Heat and Mass Transfer Spring 2008 EXAM 2 Tuesday, 18 March :00 to 8:00 PM Name: ME 315: Heat and Mass Transfer Spring 2008 EXAM 2 Tuesday, 18 March 2008 7:00 to 8:00 PM Instructions: This is an open-book eam. You may refer to your course tetbook, your class notes and your graded

More information

PIPE FLOW. General Characteristic of Pipe Flow. Some of the basic components of a typical pipe system are shown in Figure 1.

PIPE FLOW. General Characteristic of Pipe Flow. Some of the basic components of a typical pipe system are shown in Figure 1. PIPE FLOW General Characteristic of Pipe Flow Figure 1 Some of the basic components of a typical pipe system are shown in Figure 1. They include the pipes, the various fitting used to connect the individual

More information

Boundary-Layer Theory

Boundary-Layer Theory Hermann Schlichting Klaus Gersten Boundary-Layer Theory With contributions from Egon Krause and Herbert Oertel Jr. Translated by Katherine Mayes 8th Revised and Enlarged Edition With 287 Figures and 22

More information

Chapter 7: External Forced Convection. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University

Chapter 7: External Forced Convection. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Chapter 7: External Forced Convection Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Objectives When you finish studying this chapter, you should be able to: Distinguish between

More information

Chapter 8 Internal Forced Convection

Chapter 8 Internal Forced Convection Chater 8 Internal Forced Convection 8.1 Hydrodynamic Considerations 8.1.1 Flow Conditions may be determined exerimentally, as shown in Figs. 7.1-7.2. Re D ρumd μ where u m is the mean fluid velocity over

More information

10. Buoyancy-driven flow

10. Buoyancy-driven flow 10. Buoyancy-driven flow For such flows to occur, need: Gravity field Variation of density (note: not the same as variable density!) Simplest case: Viscous flow, incompressible fluid, density-variation

More information

Basic Fluid Mechanics

Basic Fluid Mechanics Basic Fluid Mechanics Chapter 6A: Internal Incompressible Viscous Flow 4/16/2018 C6A: Internal Incompressible Viscous Flow 1 6.1 Introduction For the present chapter we will limit our study to incompressible

More information

FLUID MECHANICS PROF. DR. METİN GÜNER COMPILER

FLUID MECHANICS PROF. DR. METİN GÜNER COMPILER FLUID MECHANICS PROF. DR. METİN GÜNER COMPILER ANKARA UNIVERSITY FACULTY OF AGRICULTURE DEPARTMENT OF AGRICULTURAL MACHINERY AND TECHNOLOGIES ENGINEERING 1 5. FLOW IN PIPES 5.1.3. Pressure and Shear Stress

More information

Examination Heat Transfer

Examination Heat Transfer Examination Heat Transfer code: 4B680 date: 17 january 2006 time: 14.00-17.00 hours NOTE: There are 4 questions in total. The first one consists of independent sub-questions. If necessary, guide numbers

More information

UNIT 4 HEAT TRANSFER BY CONVECTION

UNIT 4 HEAT TRANSFER BY CONVECTION UNIT 4 HEAT TRANSFER BY CONVECTION 4.1 Introduction to convection 4. Convection boundar laers 4..1 Hdrodnamic boundar laer over flat plate 4.. Thermal boundar laer 4..3 Concentration boundar laer 4.3 Dimensional

More information

Liquid or gas flow through pipes or ducts is commonly used in heating and

Liquid or gas flow through pipes or ducts is commonly used in heating and cen58933_ch08.qxd 9/4/2002 11:29 AM Page 419 INTERNAL FORCED CONVECTION CHAPTER 8 Liquid or gas flow through pipes or ducts is commonly used in heating and cooling applications. The fluid in such applications

More information

6. Laminar and turbulent boundary layers

6. Laminar and turbulent boundary layers 6. Laminar and turbulent boundary layers John Richard Thome 8 avril 2008 John Richard Thome (LTCM - SGM - EPFL) Heat transfer - Convection 8 avril 2008 1 / 34 6.1 Some introductory ideas Figure 6.1 A boundary

More information

DEPARTMENT OF MECHANICAL ENGINEERING. ME 6502 Heat and Mass Transfer III YEAR-V SEMESTER

DEPARTMENT OF MECHANICAL ENGINEERING. ME 6502 Heat and Mass Transfer III YEAR-V SEMESTER ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER ME 650 Heat and Mass Transfer III YEAR-V SEMESTER NAME :. REG.NO :. BRANCH :... YEAR & SEM :. 1 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS

More information

Lectures on Applied Reactor Technology and Nuclear Power Safety. Lecture No 6

Lectures on Applied Reactor Technology and Nuclear Power Safety. Lecture No 6 Lectures on Nuclear Power Safety Lecture No 6 Title: Introduction to Thermal-Hydraulic Analysis of Nuclear Reactor Cores Department of Energy Technology KTH Spring 2005 Slide No 1 Outline of the Lecture

More information

Phone: , For Educational Use. SOFTbank E-Book Center, Tehran. Fundamentals of Heat Transfer. René Reyes Mazzoco

Phone: , For Educational Use. SOFTbank E-Book Center, Tehran. Fundamentals of Heat Transfer. René Reyes Mazzoco 8 Fundamentals of Heat Transfer René Reyes Mazzoco Universidad de las Américas Puebla, Cholula, Mexico 1 HEAT TRANSFER MECHANISMS 1.1 Conduction Conduction heat transfer is explained through the molecular

More information

Introduction to Heat and Mass Transfer. Week 9

Introduction to Heat and Mass Transfer. Week 9 Introduction to Heat and Mass Transfer Week 9 補充! Multidimensional Effects Transient problems with heat transfer in two or three dimensions can be considered using the solutions obtained for one dimensional

More information

Heat processes. Heat exchange

Heat processes. Heat exchange Heat processes Heat exchange Heat energy transported across a surface from higher temperature side to lower temperature side; it is a macroscopic measure of transported energies of molecular motions Temperature

More information

طراحی مبدل های حرارتی مهدي کریمی ترم بهار HEAT TRANSFER CALCULATIONS

طراحی مبدل های حرارتی مهدي کریمی ترم بهار HEAT TRANSFER CALCULATIONS طراحی مبدل های حرارتی مهدي کریمی ترم بهار 96-97 HEAT TRANSFER CALCULATIONS ١ TEMPERATURE DIFFERENCE For any transfer the driving force is needed General heat transfer equation : Q = U.A. T What T should

More information

So far, we have considered conduction, which is the mechanism of heat

So far, we have considered conduction, which is the mechanism of heat cen58933_ch06.qxd 9/4/2002 12:05 PM Page 333 FUNDAMENTALS OF CONVECTION CHAPTER 6 So far, we have considered conduction, which is the mechanism of heat transfer through a solid or a quiescent fluid. We

More information

DR.PRADIP DUTTA Department of Mechanical Engineering Indian Institute of Science Bangalore

DR.PRADIP DUTTA Department of Mechanical Engineering Indian Institute of Science Bangalore DR.PRADIP DUTTA Department of Mechanical Engineering Indian Institute of Science Bangalore What is Heat Transfer? Energy in transit due to temperature difference. Thermodynamics tells us: How much heat

More information

Transient Heat Transfer Experiment. ME 331 Introduction to Heat Transfer. June 1 st, 2017

Transient Heat Transfer Experiment. ME 331 Introduction to Heat Transfer. June 1 st, 2017 Transient Heat Transfer Experiment ME 331 Introduction to Heat Transfer June 1 st, 2017 Abstract The lumped capacitance assumption for transient conduction was tested for three heated spheres; a gold plated

More information

1. Nusselt number and Biot number are computed in a similar manner (=hd/k). What are the differences between them? When and why are each of them used?

1. Nusselt number and Biot number are computed in a similar manner (=hd/k). What are the differences between them? When and why are each of them used? 1. Nusselt number and Biot number are computed in a similar manner (=hd/k). What are the differences between them? When and why are each of them used?. During unsteady state heat transfer, can the temperature

More information

2, where dp is the constant, R is the radius of

2, where dp is the constant, R is the radius of Dynamics of Viscous Flows (Lectures 8 to ) Q. Choose the correct answer (i) The average velocity of a one-dimensional incompressible fully developed viscous flow between two fixed parallel plates is m/s.

More information

Numerical Heat and Mass Transfer

Numerical Heat and Mass Transfer Master Degree in Mechanical Engineering Numerical Heat and Mass Transfer 15-Convective Heat Transfer Fausto Arpino f.arpino@unicas.it Introduction In conduction problems the convection entered the analysis

More information

Circle one: School of Mechanical Engineering Purdue University ME315 Heat and Mass Transfer. Exam #2. April 3, 2014

Circle one: School of Mechanical Engineering Purdue University ME315 Heat and Mass Transfer. Exam #2. April 3, 2014 Circle one: Div. 1 (12:30 pm, Prof. Choi) Div. 2 (9:30 am, Prof. Xu) School of Mechanical Engineering Purdue University ME315 Heat and Mass Transfer Exam #2 April 3, 2014 Instructions: Write your name

More information

CHAPTER 6 Fluids Engineering. SKMM1922 Introduction of Mechanical Engineering

CHAPTER 6 Fluids Engineering. SKMM1922 Introduction of Mechanical Engineering CHAPTER 6 Fluids Engineering SKMM1922 Introduction of Mechanical Engineering Chapter Objectives Recognize the application of fluids engineering to such diverse fields as microfluidics, aerodynamics, sports

More information

Figure 3: Problem 7. (a) 0.9 m (b) 1.8 m (c) 2.7 m (d) 3.6 m

Figure 3: Problem 7. (a) 0.9 m (b) 1.8 m (c) 2.7 m (d) 3.6 m 1. For the manometer shown in figure 1, if the absolute pressure at point A is 1.013 10 5 Pa, the absolute pressure at point B is (ρ water =10 3 kg/m 3, ρ Hg =13.56 10 3 kg/m 3, ρ oil = 800kg/m 3 ): (a)

More information

S.E. (Chemical) (Second Semester) EXAMINATION, 2011 HEAT TRANSFER (2008 PATTERN) Time : Three Hours Maximum Marks : 100

S.E. (Chemical) (Second Semester) EXAMINATION, 2011 HEAT TRANSFER (2008 PATTERN) Time : Three Hours Maximum Marks : 100 Total No. of Questions 12] [Total No. of Printed Pages 7 [4062]-186 S.E. (Chemical) (Second Semester) EXAMINATION, 2011 HEAT TRANSFER (2008 PATTERN) Time : Three Hours Maximum Marks : 100 N.B. : (i) Answers

More information

CONVECTIVE HEAT TRANSFER

CONVECTIVE HEAT TRANSFER CONVECTIVE HEAT TRANSFER Mohammad Goharkhah Department of Mechanical Engineering, Sahand Unversity of Technology, Tabriz, Iran CHAPTER 5 NATURAL CONVECTION HEAT TRANSFER BASIC CONCEPTS MECHANISM OF NATURAL

More information

Convective Heat Transfer in Parallel Plate Heat Sinks. A thesis presented to. the faculty of. In partial fulfillment

Convective Heat Transfer in Parallel Plate Heat Sinks. A thesis presented to. the faculty of. In partial fulfillment Convective Heat Transfer in Parallel Plate Heat Sinks A thesis presented to the faculty of the Russ College of Engineering and Technology of Ohio University In partial fulfillment of the requirements for

More information

Chapter 11: Heat Exchangers. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University

Chapter 11: Heat Exchangers. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Chapter 11: Heat Exchangers Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Objectives When you finish studying this chapter, you should be able to: Recognize numerous types of

More information

Laminar and Turbulent developing flow with/without heat transfer over a flat plate

Laminar and Turbulent developing flow with/without heat transfer over a flat plate Laminar and Turbulent developing flow with/without heat transfer over a flat plate Introduction The purpose of the project was to use the FLOLAB software to model the laminar and turbulent flow over a

More information

Convective Heat and Mass Transfer Prof. A. W. Date Department of Mechanical Engineering Indian Institute of Technology, Bombay

Convective Heat and Mass Transfer Prof. A. W. Date Department of Mechanical Engineering Indian Institute of Technology, Bombay Convective Heat and Mass Transfer Prof. A. W. Date Department of Mechanical Engineering Indian Institute of Technology, Bombay Module No.# 01 Lecture No. # 41 Natural Convection BLs So far we have considered

More information

True/False. Circle the correct answer. (1pt each, 7pts total) 3. Radiation doesn t occur in materials that are transparent such as gases.

True/False. Circle the correct answer. (1pt each, 7pts total) 3. Radiation doesn t occur in materials that are transparent such as gases. ME 323 Sample Final Exam. 120pts total True/False. Circle the correct answer. (1pt each, 7pts total) 1. A solid angle of 2π steradians defines a hemispherical shell. T F 2. The Earth irradiates the Sun.

More information

MIXED CONVECTION OF NEWTONIAN FLUID BETWEEN VERTICAL PARALLEL PLATES CHANNEL WITH MHD EFFECT AND VARIATION IN BRINKMAN NUMBER

MIXED CONVECTION OF NEWTONIAN FLUID BETWEEN VERTICAL PARALLEL PLATES CHANNEL WITH MHD EFFECT AND VARIATION IN BRINKMAN NUMBER Bulletin of Engineering Tome VII [14] ISSN: 67 389 1. Rasul ALIZADEH,. Alireza DARVISH BAHAMBARI, 3. Komeil RAHMDEL MIXED CONVECTION OF NEWTONIAN FLUID BETWEEN VERTICAL PARALLEL PLATES CHANNEL WITH MHD

More information

ME 144: Heat Transfer Introduction to Convection. J. M. Meyers

ME 144: Heat Transfer Introduction to Convection. J. M. Meyers ME 144: Heat Transfer Introduction to Convection Introductory Remarks Convection heat transfer differs from diffusion heat transfer in that a bulk fluid motion is present which augments the overall heat

More information

Chapter 8: Flow in Pipes

Chapter 8: Flow in Pipes Objectives 1. Have a deeper understanding of laminar and turbulent flow in pipes and the analysis of fully developed flow 2. Calculate the major and minor losses associated with pipe flow in piping networks

More information

c. The Grashof number is the ratio of buoyant forces to viscous forces acting on a fluid.

c. The Grashof number is the ratio of buoyant forces to viscous forces acting on a fluid. QUESTION 1. (0 pts) With respect to free convection: a. What is an extensive, quiescent fluid? (4 points) b. What are the two major physical considerations or forces for free convection? (4 points) c.

More information

If there is convective heat transfer from outer surface to fluid maintained at T W.

If there is convective heat transfer from outer surface to fluid maintained at T W. Heat Transfer 1. What are the different modes of heat transfer? Explain with examples. 2. State Fourier s Law of heat conduction? Write some of their applications. 3. State the effect of variation of temperature

More information

Chapter 3 Lecture 8. Drag polar 3. Topics. Chapter-3

Chapter 3 Lecture 8. Drag polar 3. Topics. Chapter-3 Chapter 3 ecture 8 Drag polar 3 Topics 3.2.7 Boundary layer separation, adverse pressure gradient and favourable pressure gradient 3.2.8 Boundary layer transition 3.2.9 Turbulent boundary layer over a

More information

Fluid Flow and Heat Transfer of Combined Forced-Natural Convection around Vertical Plate Placed in Vertical Downward Flow of Water

Fluid Flow and Heat Transfer of Combined Forced-Natural Convection around Vertical Plate Placed in Vertical Downward Flow of Water Advanced Experimental Mechanics, Vol.2 (2017), 41-46 Copyright C 2017 JSEM Fluid Flow and Heat Transfer of Combined Forced-Natural Convection around Vertical Plate Placed in Vertical Downward Flow of Water

More information

CONVECTIVE HEAT TRANSFER

CONVECTIVE HEAT TRANSFER CONVECTIVE HEAT TRANSFER Mohammad Goharkhah Department of Mechanical Engineering, Sahand Unversity of Technology, Tabriz, Iran CHAPTER 3 LAMINAR BOUNDARY LAYER FLOW LAMINAR BOUNDARY LAYER FLOW Boundary

More information

Introduction to Turbulence AEEM Why study turbulent flows?

Introduction to Turbulence AEEM Why study turbulent flows? Introduction to Turbulence AEEM 7063-003 Dr. Peter J. Disimile UC-FEST Department of Aerospace Engineering Peter.disimile@uc.edu Intro to Turbulence: C1A Why 1 Most flows encountered in engineering and

More information

In Chapters 7 and 8, we considered heat transfer by forced convection,

In Chapters 7 and 8, we considered heat transfer by forced convection, cen58933_ch09.qxd 9/4/2002 2:25 PM Page 459 NATURAL CONVECTION CHAPTER 9 In Chapters 7 and 8, we considered heat transfer by forced convection, where a fluid was forced to move over a surface or in a tube

More information