BTE5000 / PTE5000 / PTU5000 Series Precision differential pressure transmitters

Transcription

1 FEATURES 5 mbar to 0 bar, 0. to 50 psi differential pressure...6 or...0 ma Precision temperature compensated and calibrated Rugged aluminium housing Female /8" BSP and /8" NPT fittings MEDIA COMPATIBILITY Pressure inlet: Non-corrosive, non-ionic media such as air, dry gases and the like Housing: Aluminium, protection class IP 67 (according to DIN EN 6059, NEMA 6) SPECIFICATIONS 0, Maximum ratings Supply voltage current BTE(M)/PTE/PTU5...D... Source Sink current BTE(M)/PTE/PTU5...D ma 0 ma 0 ma Temperature limits Storage C Operating C Compensated C Proof pressure BTEM5x05... / PTx bar / 5 psi BTEM5x070..., BTEM5x50... /. bar / 0 psi PTx500..., PTx x rated pressure Pressure at any port BTEM5x05... / PTx bar / 50 psi bar / 75 psi...6 version Sensor GND...0 ma version Sensor R L to to GND /5

2 COMMON PERFORMAE CHARACTERISTICS 8 Thermal effects 6 ( 0 to 70 C) all 70 mbar / psid devices all 50 mbar / 5 psid devices ±0.05 ±0.008 ±0.005 ±0.00 ±0.5 ±0.00 ±0.05 ±0.05 Non-linearity and hysteresis ± 0. ± 5 Long term stability ±0. noise (0 f khz) 0.0 %FSO/ C %FSO Response time (0 to 90 %) ms INDIIDUAL PERFORMAE CHARACTERISTICS versions ( S = 5, t amb = 5 C, R L > 00 kω, com. mode pressure = 0) Z ero pressure offset BTE(M)5P... / PTx5P scale span BTE(M)5P... / PTx5P scale 6. 0 supply rejection %FSO/ impedance 50 Ω consumption 60 mw...0 ma versions ( S = 5, t amb = 5 C, R L = 00 Ω, com. mode pressure = 0) Z ero pressure offset BTE(M)5P... / PTx5P scale span BTE(M)5P... / PTx5P scale 0. 0 supply rejection ma %FSO/ impedance 0. Ω consumption (I = 0 ma) 60 mw L /5

3 LOAD LIMITATION...0 ma versions 00 Ohm operating range supply ELECTROMAGNETIC CAPABILITY 9 Radiated, radio frequency electromagnetic field immunity (RFI) Electrical fast transient / burst immunity (EFT) Electrostatic discharge immunity test (ESD) Immunity to conducted disturbances induced by radio-frequency fields EN6000--: EN6000--: EN6000--: EN : Test conditions 0 /m, 80 to % AMC ( khz) ± k MHz ± k, contact discharge ±8 k, air discharge 0.5 to 80 MHz 0, 80 % AMC ( khz) Criterion A B B A Interference < %FSO < %FSO < %FSO < %FSO Specification notes:. IP 67 protection for BTE(M)5...A / PTx5...A is given with locked connector only.. Proof pressure is the maximum pressure which may be applied without causing damage to the sensing element.. This is the highest pressure which can be applied to any port at any time. At the same time the differential pressure between the ports H and L must not exceed the maximum proof pressure.. Non-linearity refers to the Best Straight Line fit measured for offset, full scale span and / full scale span. 5. Long term stability is the change in after one year or million pressure cycles. 6. Thermal effects tested and guaranteed from 0-70 C relative to 5. All specifications shown are relative to 5 C. 7. scale span is the algebraic difference between the positive full scale and zero pressure offset. 8. Higher pressure applied to port H. 9. Test are in accordance with EN CE-labelling is in accordance with 00/08/EC.. The pressure transmitters must not be used as safety accessories according to article,.. of the directive 97//EC square rooting signal on special request. /5

4 OUTLINE DRAWING Connector version 0.0 (.58) 0.0 (0.79) NOM 86.0 (.9) 7.0 (.8).5 diam. (0.5) H: high pressure port L: low pressure port mating plug 8.0 (0.) min. M x (0.7) 8.0 (0.) min. mass: typ. 70 g x M5 (U 0-) 9.0 (0.5) BTE.../PTE...: x /8" BSP PTU...: x /8" NPT Pin - 6 Connection - 0 ma dimensions in mm (inches) Cable version 0.0 (.58) 0.0 (0.79) 90.0 (.5) 7.0 (.8).5 diam. (0.5) 8.0 (0.) min. H: high pressure port L: low pressure port m (. ft) shielded cable x 0.5 mm² (AWG) 8.0 (0.) min. mass: typ. 0 g x M5 (U 0-) 9.0 (0.5) BTE.../PTE...: x /8" BSP PTU...: x /8" NPT bare brown white green yellow Connection - 6 /shield - 0 ma /shield dimensions in mm (inches) /5

5 RECOMMENDED CABLE/CONNECTOR ACCESSORY for connector version Order number ZK0000, other cable length on special request NOM m 6.5 NOM 60 Pin PIN CONNECTION Flying lead end brown green white + shield yellow M x Included in delivery! Ø 0 ORDERING INFORMATION BT/PT x (M) 5xxx D x x Calibration BT: calibration in mbar/bar PT: calibration in psi Pressure connection E: /8" BSP female U: /8" NPT female For mbar ranges only Electrical connection A: connector version C: cable version signal :...6 :...0 ma Differential pressure Pressure range BTE5000 series PTE/PTU5000 series 005: mbar 000.: psi P05: mbar 00: 0... psi 0070: mbar P0: psi P070: mbar 005: psi 050: mbar P05: psi P50: mbar 05: psi 00: 0... bar P5: psi P0: bar 00: psi 00: 0... bar 00: psi 005: bar 50: psi 00: bar Other pressure ranges and options are widely available. Please contact First Sensor. First Sensor reserves the right to make changes to any products herein. First Sensor does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. 5/5