SGM7SZ08 Small Logic Two-Input AND Gate

Transcription

1 GENERL DESCRIPTION The is a single two-input ND gate from SGMICRO s Small Logic series. The device is fabricated with advanced CMOS technology to achieve ultra-high speed with high output drive while maintaining low static power dissipation over a broad operating range. The device is specified to operate over the 1.65V to 5.5V operating range. The inputs and output are high impedance when is 0V. Inputs tolerate voltages up to 6V, independent of operating voltage. The is available in Green SOT-23-5, SC70-5, XTDFN-1 1-6L and UTDFN L packages. It operates over an ambient temperature range of -40 to +85. FETURES Ultra-High Speed: t PD = 3.6ns (TYP) into 50pF at = 3.3V High Output Drive: ±24m at = 3V Broad Operating Range: 1.65V to 5.5V Matches Performance of LCX Operated at = 3.3V Power Down High-Impedance Inputs/Output Over-Voltage Tolerant Inputs Facilitate 5V to 3V Translation vailable in Green SOT-23-5, SC70-5, XTDFN-1 1-6L and UTDFN L Packages LOGIC SYMBOL FUNCTION TBLE B Y INPUTS OUTPUT B Y L L L L H L H L L H H H Y = B H = HIGH Logic Level L = LOW Logic Level REV.. 1

2 PCKGE/ORDERING INFORMTION MODEL PCKGE DESCRIPTION SPECIFIED TEMPERTURE RNGE ORDERING NUMBER PCKGE MRKING PCKING OPTION SC to +85 YC5G/TR SF5XX Tape and Reel, 3000 SOT to +85 YN5G/TR SF6XX Tape and Reel, 3000 XTDFN-1 1-6L -40 to +85 YXDM6G/TR G2 Tape and Reel, UTDFN L -40 to +85 YUDL6G/TR G3X Tape and Reel, 5000 NOTE: X = Date Code, XX = Date Code. MRKING INFORMTION SYY X X Date code - Month ("" = Jan. "B" = Feb. "L" = Dec.) Date code - Year ("" = 2010, "B" = 2011 ) Chip I.D. For example: SF5CC (2012, March) BSOLUTE MXIMUM RTINGS Supply Voltage, V to 6.0V DC Input Voltage, V IN V to 6.0V DC Output Voltage, V OUT V to 6.0V DC Input Diode Current, I IK (V IN < -0.5V) m DC Output Diode Current, I OK (V OUT < -0.5V) m DC Output Current, I OUT... ±50m DC or Ground Current, I CC or I GND... ±50m Operating Temperature Range to +85 Junction Temperature Storage Temperature Range to +150 Lead Temperature (Soldering, 10sec) ESD Susceptibility HBM V MM...400V CUTION This integrated circuit can be damaged by ESD if you don t pay attention to ESD protection. SGMICRO recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. SGMICRO reserves the right to make any change in circuit design, specification or other related things if necessary without notice at any time. Please contact SGMICRO sales office to get the latest datasheet. NOTE: Stresses beyond those listed under bsolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2

3 PIN CONFIGURTIONS (TOP VIEW) 1 6 B 2 5 NC GND 3 4 Y XTDFN-1 1-6L B 1 2 SYYxx 5 B NC GND 3 4 Y GND 3 4 Y SOT-23-5/SC70-5 UTDFN L PIN DESCRIPTION SOT-23-5 SC70-5 PIN UTDFN L XTDFN-1 1-6L NME FUNCTION 1 1 Input. Unused input must be held high or low. It may not float. 2 2 B Input. Unused input must be held high or low. It may not float. 3 3 GND Ground. 4 4 Y Output. 5 6 Power Supply. 5 NC No Connection. 3

4 ELECTRICL CHRCTERISTICS (T = -40 C to +85 C, typical values are at T = +25 C, unless otherwise noted.) GENERL PRMETER SYMBOL CONDITIONS (V) MIN TYP MX UNITS Power Supply Range Supply Voltage Data Retention Input Voltage V IN V Output Voltage V OUT 0.00 V Input Rise and Fall Times DC PERFORMNCE t r, t f 1.8, 2.5 ± ± ± HIGH Level Input Voltage V IH 1.65 to V LOW Level Input Voltage V IL 1.65 to V HIGH Level Output Voltage V OH V IN = V IH LOW Level Output Voltage V OL V IN = V IL I OH = -100µ I OH = -4m I OH = -8m I OH = -16m I OH = -24m I OH = -32m I OL = 100µ I OL = 4m I OL = 8m I OL = 16m I OL = 24m I OL = 32m Input Leakage Current I IN V IN = 5.5V, GND 0 to 5.5 ±0.10 ±5 μ Power Off Leakage Current I OFF V IN or V OUT = 5.5V μ Quiescent Supply Current I CC V IN = 5.5V, GND 1.65 to μ V ns/v V V 4

5 ELECTRICL CHRCTERISTICS (Typical values are at T = +25 C, unless otherwise noted.) PRMETER SYMBOL CONDITIONS MIN TYP MX UNITS C PERFORMNCE Propagation Delay t PHL, t PLH = 1.65V 8.8 = 1.80V C L = 15pF, 7.2 = 2.50V ± 0.20V R L = 1MΩ, 4.1 = 3.30V ± 0.30V Figure 1, Figure = 5.00V ± 0.50V 2.6 = 3.30V ± 0.30V C L = 50pF, R L = 500Ω, 3.6 = 5.00V ± 0.50V Figure 1, Figure Input Capacitance C IN = 0V 4.0 pf Power Dissipation Capacitance (2) C PD = 3.30V 19.0 Figure 3 = 5.00V 20.0 NOTES: 1. Unused inputs must be held HIGH or LOW. They may not float. 2. C PD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (I CCD ) at no output loading and operating at 50% duty cycle (see Figure 3). C PD is related to dynamic operating current I CCD by the expression: I CCD = (C PD) () (f IN) + (I CC,Static). ns pf 5

6 TEST CIRCUITS t r = 3ns t f = 3ns 90% 90% INPUT 50% 50% INPUT C L R L OUTPUT 10% 10% t W t PHL t PLH GND V OH OUTPUT 50% 50% C L includes load and stray capacitance; Input PRR = 1.0MHz; t W = 500ns. V OL Figure 1. C Test Circuit Figure 2. C Waveforms INPUT Input = C Waveform; t r = t f = 1.8ns; PRR = 10MHz; Duty Cycle = 50%. Figure 3. I CCD Test Circuit 6

7 PCKGE OUTLINE DIMENSIONS SC70-5 D e e E1 E 1.9 b RECOMMENDED LND PTTERN (Unit: mm) L L1 1 2 θ 0.20 c Symbol In Millimeters In Inches MIN MX MIN MX b c D E E e 0.65 TYP TYP e BSC BSC L REF REF L θ

8 PCKGE OUTLINE DIMENSIONS SOT-23-5 D 1.90 e1 E1 E b e RECOMMENDED LND PTTERN (Unit: mm) L 1 2 θ 0.2 c In Millimeters In Inches Symbol MIN MX MIN MX b c D E E e BSC BSC e BSC BSC L θ

9 PCKGE OUTLINE DIMENSIONS UTDFN L D e N6 E L b N1 TOP VIEW BOTTOM VIEW SIDE VIEW RECOMMENDED LND PTTERN (Unit: mm) In Millimeters In Inches Symbol MIN MX MIN MX REF REF D E b e TYP TYP L

10 PCKGE OUTLINE DIMENSIONS XTDFN-1 1-6L D e N6 E TOP VIEW k L N1 b BOTTOM VIEW L SIDE VIEW RECOMMENDED LND PTTERN (Unit: mm) In Millimeters In Inches Symbol MIN MX MIN MX REF REF D E k MIN MIN b e TYP TYP L L

11 TPE ND REEL INFORMTION REEL DIMENSIONS TPE DIMENSIONS P2 P0 W Q1 Q2 Q1 Q2 Q1 Q2 B0 Q3 Q4 Q3 Q4 Q3 Q4 Reel Diameter P1 0 K0 Reel Width (W1) DIRECTION OF FEED NOTE: The picture is only for reference. Please make the object as the standard. KEY PRMETER LIST OF TPE ND REEL Package Type Reel Diameter Reel Width W1 0 B0 K0 P0 P1 P2 W Pin1 Quadrant SOT Q3 SC Q3 UTDFN L Q1 XTDFN-1 1-6L Q1 11

12 CRTON BOX DIMENSIONS NOTE: The picture is only for reference. Please make the object as the standard. KEY PRMETER LIST OF CRTON BOX Reel Type Length Width Height Pizza/Carton 7 (Option)