Exam 3 April 16, 2014

Size: px
Start display at page:

Download "Exam 3 April 16, 2014"

Transcription

1 Exam 3 Instructions: You have 60 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use a calculator during the exam. Usage of mobile phones and other electronic communication devices is NOT permitted during the exam. Problem 1 (20 pts) 2 (20 pts) 3 (20 pts) Total Score Name: Section (circle): 8:30-9:20 11:30-12:20 2:30-3:20 Exam 3 Page 1 of 8

2 Problem 1 (20 points): Given: A stepped drum (having a mass of m D and radius of gyration about its center O of k O ) is attached to a smooth shaft passing through its center O. The cable wrapped around the outer radius of the drum is attached to block A. A second cable is wrapped around the inner radius of the drum with this cable pulled over an ideal pulley that is attached to the car with mass m C. Assume that the cables do not slip on the drum. The system is at rest when the car is at height h off the ground. Find: The angular acceleration of the drum immediately after release. Equations approach and write your final answer as a vector. Use the Newton-Euler Use the following parameters in your analysis: m A = 10 kg, m c = 1500 kg, m D = 25 kg, k O = 0.35 m, R = 0.50 m, r = 0.25 m, and h = 1 m. m D m c m A h Exam 3 Page 2 of 8

3 This page is for extra work related to Problem 1. Exam 3 Page 3 of 8

4 Problem 2 (20 points): Given: A homogeneous, rigid bar (of mass m and length l) is pinned to the block at O. The block has a mass of 2m. The whole system is released from rest when θ = 0. Find: When the bar reaches θ = 90 : (a) Determine the velocity of the bar s center of mass G. Write your answer as a vector. (b) Determine the velocity of the block. Write your answer as a vector. Exam 3 Page 4 of 8

5 This page is for extra work related to Problem 2. Exam 3 Page 5 of 8

6 Problem 3 (20 points): Part A (4 points): Circle ALL of the expressions below that are a correction formulation of the Euler Equation that describes the angular acceleration of the disk with mass center G and geometric center O? (a) ΣM D = I D α (b) ΣM E = I E α (c) ΣM O = I O α (d) ΣM G = I G α Part B (4 points): For the homogeneous disk shown below, G is the mass center, and points A and B are distances a and b from the mass center, respectively. Circle the answer below that correctly relates the mass moment of inertia about A (I A ) to that about point B (I B ): (a) I A = I B (b) I A = I B + ma 2 (c) I A = I B + mb 2 (d) I A = I B + m(a 2 b 2 ) Exam 3 Page 6 of 8

7 The center of the disk shown below has a downward acceleration. Assume the cable does not slip. Part C (3 points): Sketch a Free Body Diagram of the Disk. Part D (3 points): Circle the answer that most accurately describes the tension in section AB of the cable: (a) The tension in section AB is equal to the tension in section CD. (b) The tension in section AB is smaller than the tension in section CD. (c) The tension in section AB is larger than the tension in section CD. (d) More information is needed to answer the question. Exam 3 Page 7 of 8

8 Part E (6 points): Particle A strikes particle B with a known speed v A1. The coefficient of restitution is known to be less than one (e < 1). Particle B is attached to a rigid bar which is pinned to ground. Circle all of the responses below that correctly describe the impact of particle A and particle B: For the particle A: (a) Linear momentum of particle A is conserved in the x-direction. (b) Linear momentum of particle A is conserved in the y-direction. (c) Linear momentum of particle A is conserved in the n-direction. (d) none of the above. For the system A+B: (a) Linear momentum of the system A+B is conserved in the x-direction. (b) Linear momentum of the system A+B is conserved in the y-direction. (c) The total energy of the system A+B is conserved. (d) none of the above. Exam 3 Page 8 of 8

Exam 3 December 1, 2010

Exam 3 December 1, 2010 Exam 3 Instructions: You have 60 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use a calculator during the exam. All work must be shown to receive credit.

More information

Final Exam April 30, 2013

Final Exam April 30, 2013 Final Exam Instructions: You have 120 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use a calculator during the exam. Usage of mobile phones and other electronic

More information

Final Exam December 15, 2014

Final Exam December 15, 2014 Final Exam Instructions: You have 120 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use the ME approved calculator only during the exam. Usage of mobile phones

More information

Exam 1 January 31, 2012

Exam 1 January 31, 2012 Exam 1 Instructions: You have 60 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use a calculator during the exam. Usage of mobile phones and other electronic

More information

Final Exam December 13, 2016

Final Exam December 13, 2016 Final Exam Instructions: You have 120 minutes to complete this exam. This is a closed-boo, closed-notes exam. You are allowed to use a calculator during the exam. Do NOT unstaple your exam. Do NOT write

More information

ME 274: Basic Mechanics II Spring April 18, Problem 1 (24 points):

ME 274: Basic Mechanics II Spring April 18, Problem 1 (24 points): Problem 1 (24 points): Given: The block shown in the figure slides on a smooth surface. A thin homogenous bar is attached to the block and is free to rotate about a pin joint at A. At the instant shown

More information

Exam 1 September 11, 2013

Exam 1 September 11, 2013 Exam 1 Instructions: You have 60 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use an approved calculator during the exam. Usage of mobile phones and other

More information

8.012 Physics I: Classical Mechanics Fall 2008

8.012 Physics I: Classical Mechanics Fall 2008 MIT OpenCourseWare http://ocw.mit.edu 8.012 Physics I: Classical Mechanics Fall 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. MASSACHUSETTS INSTITUTE

More information

Exam 2 March 12, 2014

Exam 2 March 12, 2014 Exam 2 Instructions: You have 60 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use a calculator during the exam. Usage of mobile phones and other electronic

More information

Exam 2 October 17, 2013

Exam 2 October 17, 2013 Exam 2 Instructions: You have 60 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use an approved calculator during the exam. Usage of mobile phones and other

More information

8.012 Physics I: Classical Mechanics Fall 2008

8.012 Physics I: Classical Mechanics Fall 2008 MIT OpenCourseWare http://ocw.mit.edu 8.012 Physics I: Classical Mechanics Fall 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. MASSACHUSETTS INSTITUTE

More information

The University of Melbourne Engineering Mechanics

The University of Melbourne Engineering Mechanics The University of Melbourne 436-291 Engineering Mechanics Tutorial Eleven Instantaneous Centre and General Motion Part A (Introductory) 1. (Problem 5/93 from Meriam and Kraige - Dynamics) For the instant

More information

EQUATIONS OF MOTION: GENERAL PLANE MOTION (Section 17.5) Today s Objectives: Students will be able to analyze the planar kinetics of a rigid body

EQUATIONS OF MOTION: GENERAL PLANE MOTION (Section 17.5) Today s Objectives: Students will be able to analyze the planar kinetics of a rigid body EQUATIONS OF MOTION: GENERAL PLANE MOTION (Section 17.5) Today s Objectives: Students will be able to analyze the planar kinetics of a rigid body undergoing general plane motion. APPLICATIONS As the soil

More information

Physics 201 Exam 3 (Monday, November 5) Fall 2012 (Saslow)

Physics 201 Exam 3 (Monday, November 5) Fall 2012 (Saslow) Physics 201 Exam 3 (Monday, November 5) Fall 2012 (Saslow) Name (printed) Lab Section(+2 pts) Name (signed as on ID) Multiple choice Section. Circle the correct answer. No work need be shown and no partial

More information

Q16.: A 5.0 kg block is lowered with a downward acceleration of 2.8 m/s 2 by means of a rope. The force of the block on the rope is:(35 N, down)

Q16.: A 5.0 kg block is lowered with a downward acceleration of 2.8 m/s 2 by means of a rope. The force of the block on the rope is:(35 N, down) Old Exam Question Ch. 5 T072 Q13.Two blocks of mass m 1 = 24.0 kg and m 2, respectively, are connected by a light string that passes over a massless pulley as shown in Fig. 2. If the tension in the string

More information

Plane Motion of Rigid Bodies: Forces and Accelerations

Plane Motion of Rigid Bodies: Forces and Accelerations Plane Motion of Rigid Bodies: Forces and Accelerations Reference: Beer, Ferdinand P. et al, Vector Mechanics for Engineers : Dynamics, 8 th Edition, Mc GrawHill Hibbeler R.C., Engineering Mechanics: Dynamics,

More information

UNIVERSITY OF SASKATCHEWAN GE MECHANICS III FINAL EXAM APRIL 18, 2011 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS

UNIVERSITY OF SASKATCHEWAN GE MECHANICS III FINAL EXAM APRIL 18, 2011 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS UNIVERSITY OF SASKATCHEWAN GE 226.3 MECHANICS III FINAL EXAM APRIL 18, 2011 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS LAST NAME (printed): FIRST NAME (printed): STUDENT NUMBER: EXAMINATION

More information

Please circle the name of your instructor: EB01: Beamish EB02: Fenrich EB03: Ruhl. EB04: Rahman EB05: Nedie EB06: Ropchan LAST NAME: FIRST NAME: ID#:

Please circle the name of your instructor: EB01: Beamish EB02: Fenrich EB03: Ruhl. EB04: Rahman EB05: Nedie EB06: Ropchan LAST NAME: FIRST NAME: ID#: Faculty of Engineering and Department of Physics ENPH 131 Final Examination Saturday, April 20, 2013; 2:00 pm 4:30 pm Universiade Pavilion Section EB01 (BEAMISH): Rows 1, 3, 5(seats 1-45) Section EB02

More information

Physics 211 Spring 2014 Final Practice Exam

Physics 211 Spring 2014 Final Practice Exam Physics 211 Spring 2014 Final Practice Exam This exam is closed book and notes. A formula sheet will be provided for you at the end of the final exam you can download a copy for the practice exam from

More information

8.012 Physics I: Classical Mechanics Fall 2008

8.012 Physics I: Classical Mechanics Fall 2008 MIT OpenCourseWare http://ocw.mit.edu 8.012 Physics I: Classical Mechanics Fall 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. MASSACHUSETTS INSTITUTE

More information

PHYSICS 221 SPRING 2015

PHYSICS 221 SPRING 2015 PHYSICS 221 SPRING 2015 EXAM 2: April 2, 2015 8:15-10:15pm Name (printed): Recitation Instructor: Section # INSTRUCTIONS: This exam contains 25 multiple-choice questions plus 2 extra credit questions,

More information

7.6 Journal Bearings

7.6 Journal Bearings 7.6 Journal Bearings 7.6 Journal Bearings Procedures and Strategies, page 1 of 2 Procedures and Strategies for Solving Problems Involving Frictional Forces on Journal Bearings For problems involving a

More information

5. Plane Kinetics of Rigid Bodies

5. Plane Kinetics of Rigid Bodies 5. Plane Kinetics of Rigid Bodies 5.1 Mass moments of inertia 5.2 General equations of motion 5.3 Translation 5.4 Fixed axis rotation 5.5 General plane motion 5.6 Work and energy relations 5.7 Impulse

More information

Anna University May/June 2013 Exams ME2151 Engineering Mechanics Important Questions.

Anna University May/June 2013 Exams ME2151 Engineering Mechanics Important Questions. Anna University May/June 2013 Exams ME2151 Engineering Mechanics Important Questions 1. Find the resultant force and its direction for the given figure 2. Two forces are acting at a point O as shown in

More information

8.012 Physics I: Classical Mechanics Fall 2008

8.012 Physics I: Classical Mechanics Fall 2008 IT OpenCourseWare http://ocw.mit.edu 8.012 Physics I: Classical echanics Fall 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. ASSACHUSETTS INSTITUTE

More information

1 MR SAMPLE EXAM 3 FALL 2013

1 MR SAMPLE EXAM 3 FALL 2013 SAMPLE EXAM 3 FALL 013 1. A merry-go-round rotates from rest with an angular acceleration of 1.56 rad/s. How long does it take to rotate through the first rev? A) s B) 4 s C) 6 s D) 8 s E) 10 s. A wheel,

More information

8.012 Physics I: Classical Mechanics Fall 2008

8.012 Physics I: Classical Mechanics Fall 2008 MIT OpenCourseWare http://ocw.mit.edu 8.012 Physics I: Classical Mechanics Fall 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. MASSACHUSETTS INSTITUTE

More information

16.07 Dynamics. Problem Set 10

16.07 Dynamics. Problem Set 10 NAME :..................... Massachusetts Institute of Technology 16.07 Dynamics Problem Set 10 Out date: Nov. 7, 2007 Due date: Nov. 14, 2007 Problem 1 Problem 2 Problem 3 Problem 4 Study Time Time Spent

More information

Circular motion minutes. 62 marks. theonlinephysicstutor.com. facebook.com/theonlinephysicstutor Page 1 of 22. Name: Class: Date: Time: Marks:

Circular motion minutes. 62 marks. theonlinephysicstutor.com. facebook.com/theonlinephysicstutor Page 1 of 22. Name: Class: Date: Time: Marks: Circular motion 2 Name: Class: Date: Time: 67 minutes Marks: 62 marks Comments: Page 1 of 22 1 A lead ball of mass 0.25 kg is swung round on the end of a string so that the ball moves in a horizontal circle

More information

DYNAMICS ME HOMEWORK PROBLEM SETS

DYNAMICS ME HOMEWORK PROBLEM SETS DYNAMICS ME 34010 HOMEWORK PROBLEM SETS Mahmoud M. Safadi 1, M.B. Rubin 2 1 safadi@technion.ac.il, 2 mbrubin@technion.ac.il Faculty of Mechanical Engineering Technion Israel Institute of Technology Spring

More information

ME 274 Spring 2017 Examination No. 2 PROBLEM No. 2 (20 pts.) Given:

ME 274 Spring 2017 Examination No. 2 PROBLEM No. 2 (20 pts.) Given: PROBLEM No. 2 (20 pts.) Given: Blocks A and B (having masses of 2m and m, respectively) are connected by an inextensible cable, with the cable being pulled over a small pulley of negligible mass. Block

More information

Mechanics II. Which of the following relations among the forces W, k, N, and F must be true?

Mechanics II. Which of the following relations among the forces W, k, N, and F must be true? Mechanics II 1. By applying a force F on a block, a person pulls a block along a rough surface at constant velocity v (see Figure below; directions, but not necessarily magnitudes, are indicated). Which

More information

8.012 Physics I: Classical Mechanics Fall 2008

8.012 Physics I: Classical Mechanics Fall 2008 MIT OpenCourseWare http://ocw.mit.edu 8.012 Physics I: Classical Mechanics Fall 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. MASSACHUSETTS INSTITUTE

More information

CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5

CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5 1 / 36 CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5 Prof. Albert S. Kim Civil and Environmental Engineering, University of Hawaii at Manoa Date: 2 / 36 EQUATIONS OF MOTION: ROTATION

More information

Page 2 (20) Page 3 (12) Page 4 (14) Page 5 (14) Total (60) PHYSICS 11 (Fall 2003) Exam 3. Elementary Physics November 21, 2003 SCORE BOX

Page 2 (20) Page 3 (12) Page 4 (14) Page 5 (14) Total (60) PHYSICS 11 (Fall 2003) Exam 3. Elementary Physics November 21, 2003 SCORE BOX INSTRUCTIONS: Except for the multiple choice questions 1 5, you must show all your work. An answer will not be enough; understanding must be demonstrated as well. This can take the form of a clear calculation,

More information

第 1 頁, 共 7 頁 Chap10 1. Test Bank, Question 3 One revolution per minute is about: 0.0524 rad/s 0.105 rad/s 0.95 rad/s 1.57 rad/s 6.28 rad/s 2. *Chapter 10, Problem 8 The angular acceleration of a wheel

More information

PHYSICS 221 Fall 2007 EXAM 2: November 14, :00pm 10:00pm

PHYSICS 221 Fall 2007 EXAM 2: November 14, :00pm 10:00pm PHYSICS 221 Fall 2007 EXAM 2: November 14, 2007 8:00pm 10:00pm Name (printed): Recitation Instructor: Section # INSTRUCTIONS: This exam contains 25 multiple-choice questions plus 2 extra credit questions,

More information

Chapter 10 Practice Test

Chapter 10 Practice Test Chapter 10 Practice Test 1. At t = 0, a wheel rotating about a fixed axis at a constant angular acceleration of 0.40 rad/s 2 has an angular velocity of 1.5 rad/s and an angular position of 2.3 rad. What

More information

E 490 FE Exam Prep. Engineering Mechanics

E 490 FE Exam Prep. Engineering Mechanics E 490 FE Exam Prep Engineering Mechanics 2008 E 490 Course Topics Statics Newton s Laws of Motion Resultant Force Systems Moment of Forces and Couples Equilibrium Pulley Systems Trusses Centroid of an

More information

Review questions. Before the collision, 70 kg ball is stationary. Afterward, the 30 kg ball is stationary and 70 kg ball is moving to the right.

Review questions. Before the collision, 70 kg ball is stationary. Afterward, the 30 kg ball is stationary and 70 kg ball is moving to the right. Review questions Before the collision, 70 kg ball is stationary. Afterward, the 30 kg ball is stationary and 70 kg ball is moving to the right. 30 kg 70 kg v (a) Is this collision elastic? (b) Find the

More information

Name SOLUTION Student ID Score Speed of blocks is is decreasing. Part III. [25 points] Two blocks move on a frictionless

Name SOLUTION Student ID Score Speed of blocks is is decreasing. Part III. [25 points] Two blocks move on a frictionless Name SOLUTION Student ID Score last first Speed of blocks is is decreasing. Part III. [25 points] Two blocks move on a frictionless v o incline with initial speed v o, as shown, while a hand pushes with

More information

SECTION A. 8 kn/m. C 3 m 3m

SECTION A. 8 kn/m. C 3 m 3m SECTION Question 1 150 m 40 kn 5 kn 8 kn/m C 3 m 3m D 50 ll dimensions in mm 15 15 Figure Q1(a) Figure Q1(b) The horizontal beam CD shown in Figure Q1(a) has a uniform cross-section as shown in Figure

More information

Practice Test 3. Name: Date: ID: A. Multiple Choice Identify the choice that best completes the statement or answers the question.

Practice Test 3. Name: Date: ID: A. Multiple Choice Identify the choice that best completes the statement or answers the question. Name: Date: _ Practice Test 3 Multiple Choice Identify the choice that best completes the statement or answers the question. 1. A wheel rotates about a fixed axis with an initial angular velocity of 20

More information

Faculty of Engineering and Department of Physics Engineering Physics 131 Final Examination Saturday April 21, 2018; 14:00 pm 16:30 pm

Faculty of Engineering and Department of Physics Engineering Physics 131 Final Examination Saturday April 21, 2018; 14:00 pm 16:30 pm Faculty of Engineering and Department of Physics Engineering Physics 131 Final Examination Saturday April 21, 2018; 14:00 pm 16:30 pm 1. Closed book exam. No notes or textbooks allowed. 2. Formula sheets

More information

PHYSICS 221 SPRING 2014

PHYSICS 221 SPRING 2014 PHYSICS 221 SPRING 2014 EXAM 2: April 3, 2014 8:15-10:15pm Name (printed): Recitation Instructor: Section # INSTRUCTIONS: This exam contains 25 multiple-choice questions plus 2 extra credit questions,

More information

6. Find the net torque on the wheel in Figure about the axle through O if a = 10.0 cm and b = 25.0 cm.

6. Find the net torque on the wheel in Figure about the axle through O if a = 10.0 cm and b = 25.0 cm. 1. During a certain period of time, the angular position of a swinging door is described by θ = 5.00 + 10.0t + 2.00t 2, where θ is in radians and t is in seconds. Determine the angular position, angular

More information

PHY 001 (Physics I) Lecture 7

PHY 001 (Physics I) Lecture 7 PHY 001 (Physics I) Instructor: Dr. Mohamed Fouad Salem mohamed.salem@gmail.com Textbook University Physics, 12 th edition, Young and Freedman Course Material Website http://meryesk.wordpress.com/phy001/

More information

Rotational Motion. Rotational Motion. Rotational Motion

Rotational Motion. Rotational Motion. Rotational Motion I. Rotational Kinematics II. Rotational Dynamics (Netwton s Law for Rotation) III. Angular Momentum Conservation 1. Remember how Newton s Laws for translational motion were studied: 1. Kinematics (x =

More information

Your Name: PHYSICS 101 MIDTERM. Please circle your section 1 9 am Galbiati 2 10 am Kwon 3 11 am McDonald 4 12:30 pm McDonald 5 12:30 pm Kwon

Your Name: PHYSICS 101 MIDTERM. Please circle your section 1 9 am Galbiati 2 10 am Kwon 3 11 am McDonald 4 12:30 pm McDonald 5 12:30 pm Kwon 1 Your Name: PHYSICS 101 MIDTERM October 26, 2006 2 hours Please circle your section 1 9 am Galbiati 2 10 am Kwon 3 11 am McDonald 4 12:30 pm McDonald 5 12:30 pm Kwon Problem Score 1 /13 2 /20 3 /20 4

More information

Rotation. PHYS 101 Previous Exam Problems CHAPTER

Rotation. PHYS 101 Previous Exam Problems CHAPTER PHYS 101 Previous Exam Problems CHAPTER 10 Rotation Rotational kinematics Rotational inertia (moment of inertia) Kinetic energy Torque Newton s 2 nd law Work, power & energy conservation 1. Assume that

More information

Physics 121, Final Exam Do not turn the pages of the exam until you are instructed to do so.

Physics 121, Final Exam Do not turn the pages of the exam until you are instructed to do so. , Final Exam Do not turn the pages of the exam until you are instructed to do so. You are responsible for reading the following rules carefully before beginning. Exam rules: You may use only a writing

More information

Name: Fall 2014 CLOSED BOOK

Name: Fall 2014 CLOSED BOOK Name: Fall 2014 1. Rod AB with weight W = 40 lb is pinned at A to a vertical axle which rotates with constant angular velocity ω =15 rad/s. The rod position is maintained by a horizontal wire BC. Determine

More information

Sample Final Exam 02 Physics 106 (Answers on last page)

Sample Final Exam 02 Physics 106 (Answers on last page) Sample Final Exam 02 Physics 106 (Answers on last page) Name (Print): 4 Digit ID: Section: Instructions: 1. There are 30 multiple choice questions on the test. There is no penalty for guessing, so you

More information

Planar Rigid Body Kinematics Homework

Planar Rigid Body Kinematics Homework Chapter 2: Planar Rigid ody Kinematics Homework Chapter 2 Planar Rigid ody Kinematics Homework Freeform c 2018 2-1 Chapter 2: Planar Rigid ody Kinematics Homework 2-2 Freeform c 2018 Chapter 2: Planar

More information

Physics 218 Exam III

Physics 218 Exam III Physics 218 Exam III Spring 2017 (all sections) April 17 th, 2017 Rules of the exam: Please fill out the information and read the instructions below, but do not open the exam until told to do so. 1. You

More information

PHY 111L Activity 9 Moments of Inertia

PHY 111L Activity 9 Moments of Inertia PHY 111L Activity 9 Moments of Inertia Name: Section: ID #: Date: Lab Partners: TA initials: Objectives 1. Introduce moment of inertia for different objects 2. Understand the moment of inertia apparatus

More information

Phys 270 Final Exam. Figure 1: Question 1

Phys 270 Final Exam. Figure 1: Question 1 Phys 270 Final Exam Time limit: 120 minutes Each question worths 10 points. Constants: g = 9.8m/s 2, G = 6.67 10 11 Nm 2 kg 2. 1. (a) Figure 1 shows an object with moment of inertia I and mass m oscillating

More information

Exam 02: Chapters 16 19

Exam 02: Chapters 16 19 NAME: Exam 02: Chapters 16 19 Instructions Solve six of the following problems to the best of your ability. You have two hours in which to complete this exam. Choose one problem from each chapter, then

More information

13-Nov-2015 PHYS Rotational Inertia

13-Nov-2015 PHYS Rotational Inertia Objective Rotational Inertia To determine the rotational inertia of rigid bodies and to investigate its dependence on the distance to the rotation axis. Introduction Rotational Inertia, also known as Moment

More information

ROTATIONAL DYNAMICS AND STATIC EQUILIBRIUM

ROTATIONAL DYNAMICS AND STATIC EQUILIBRIUM ROTATIONAL DYNAMICS AND STATIC EQUILIBRIUM Chapter 11 Units of Chapter 11 Torque Torque and Angular Acceleration Zero Torque and Static Equilibrium Center of Mass and Balance Dynamic Applications of Torque

More information

VALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR DEPARTMENT OF MECHANICAL ENGINEERING

VALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR DEPARTMENT OF MECHANICAL ENGINEERING VALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR 603203 DEPARTMENT OF MECHANICAL ENGINEERING BRANCH: MECHANICAL YEAR / SEMESTER: I / II UNIT 1 PART- A 1. State Newton's three laws of motion? 2.

More information

Problem Set x Classical Mechanics, Fall 2016 Massachusetts Institute of Technology. 1. Moment of Inertia: Disc and Washer

Problem Set x Classical Mechanics, Fall 2016 Massachusetts Institute of Technology. 1. Moment of Inertia: Disc and Washer 8.01x Classical Mechanics, Fall 2016 Massachusetts Institute of Technology Problem Set 10 1. Moment of Inertia: Disc and Washer (a) A thin uniform disc of mass M and radius R is mounted on an axis passing

More information

Name Student ID Score Last First. I = 2mR 2 /5 around the sphere s center of mass?

Name Student ID Score Last First. I = 2mR 2 /5 around the sphere s center of mass? NOTE: ignore air resistance in all Questions. In all Questions choose the answer that is the closest!! Question I. (15 pts) Rotation 1. (5 pts) A bowling ball that has an 11 cm radius and a 7.2 kg mass

More information

Chap. 10: Rotational Motion

Chap. 10: Rotational Motion Chap. 10: Rotational Motion I. Rotational Kinematics II. Rotational Dynamics - Newton s Law for Rotation III. Angular Momentum Conservation (Chap. 10) 1 Newton s Laws for Rotation n e t I 3 rd part [N

More information

[1.] This problem has five multiple choice questions. Circle the best answer in each case.

[1.] This problem has five multiple choice questions. Circle the best answer in each case. [1.] This problem has five multiple choice questions. Circle the best answer in each case. [1A.] A force given by 1 2 3, acts on a particle positioned at 2 6. What is its torque about the origin? [a] 18

More information

Dynamics Plane kinematics of rigid bodies Section 4: TJW Rotation: Example 1

Dynamics Plane kinematics of rigid bodies Section 4: TJW Rotation: Example 1 Section 4: TJW Rotation: Example 1 The pinion A of the hoist motor drives gear B, which is attached to the hoisting drum. The load L is lifted from its rest position and acquires an upward velocity of

More information

Moment of Inertia Race

Moment of Inertia Race Review Two points, A and B, are on a disk that rotates with a uniform speed about an axis. Point A is closer to the axis than point B. Which of the following is NOT true? 1. Point B has the greater tangential

More information

Rotation review packet. Name:

Rotation review packet. Name: Rotation review packet. Name:. A pulley of mass m 1 =M and radius R is mounted on frictionless bearings about a fixed axis through O. A block of equal mass m =M, suspended by a cord wrapped around the

More information

Physics 218 Exam III

Physics 218 Exam III Physics 218 Exam III Fall 2017 (all sections) November 15 th, 2017 Please fill out the information and read the instructions below, but do not open the exam until told to do so. Rules of the exam: 1. You

More information

TOPIC D: ROTATION EXAMPLES SPRING 2018

TOPIC D: ROTATION EXAMPLES SPRING 2018 TOPIC D: ROTATION EXAMPLES SPRING 018 Q1. A car accelerates uniformly from rest to 80 km hr 1 in 6 s. The wheels have a radius of 30 cm. What is the angular acceleration of the wheels? Q. The University

More information

PHYSICS 107 FINAL EXAMINATION

PHYSICS 107 FINAL EXAMINATION PRINTED NAME: Problem Score 1 /20 2 /20 3 /20 4 /20 5 /20 6 /20 Total /120 PHYSICS 107 FINAL EXAMINATION January 24, 2001 8:30 11:30 am When you are told to begin, check that this examination booklet contains

More information

Rotational Motion. 1 Introduction. 2 Equipment. 3 Procedures. 3.1 Initializing the Software. 3.2 Single Platter Experiment

Rotational Motion. 1 Introduction. 2 Equipment. 3 Procedures. 3.1 Initializing the Software. 3.2 Single Platter Experiment Rotational Motion Introduction In this lab you will investigate different aspects of rotational motion, including moment of inertia and the conservation of energy using the smart pulley and the rotation

More information

PHYSICS 221 SPRING 2013

PHYSICS 221 SPRING 2013 PHYSICS 221 SPRING 2013 EXAM 2: April 4, 2013 8:15-10:15pm Name (printed): Recitation Instructor: Section # INSTRUCTIONS: This exam contains 25 multiple-choice questions plus 2 extra credit questions,

More information

1. Replace the given system of forces acting on a body as shown in figure 1 by a single force and couple acting at the point A.

1. Replace the given system of forces acting on a body as shown in figure 1 by a single force and couple acting at the point A. Code No: Z0321 / R07 Set No. 1 I B.Tech - Regular Examinations, June 2009 CLASSICAL MECHANICS ( Common to Mechanical Engineering, Chemical Engineering, Mechatronics, Production Engineering and Automobile

More information

TOPIC E: OSCILLATIONS EXAMPLES SPRING Q1. Find general solutions for the following differential equations:

TOPIC E: OSCILLATIONS EXAMPLES SPRING Q1. Find general solutions for the following differential equations: TOPIC E: OSCILLATIONS EXAMPLES SPRING 2019 Mathematics of Oscillating Systems Q1. Find general solutions for the following differential equations: Undamped Free Vibration Q2. A 4 g mass is suspended by

More information

DO NOT separate the pages of the exam containing the problems. B01: Chow B02: Fenrich B03: Schiavone. B04: Lavoie B05: Wheelock B06: Tang

DO NOT separate the pages of the exam containing the problems. B01: Chow B02: Fenrich B03: Schiavone. B04: Lavoie B05: Wheelock B06: Tang Faculty of Engineering and Department of Physics ENPH 131 Final Examination Saturday, April 21, 2012; 2:00 pm 4:30 pm Universiade Pavilion Section EB01: Rows 1, 3, 5 (seats 1-16) Section EB02: Rows 5 (seats

More information

Chapter 8. Rotational Equilibrium and Rotational Dynamics. 1. Torque. 2. Torque and Equilibrium. 3. Center of Mass and Center of Gravity

Chapter 8. Rotational Equilibrium and Rotational Dynamics. 1. Torque. 2. Torque and Equilibrium. 3. Center of Mass and Center of Gravity Chapter 8 Rotational Equilibrium and Rotational Dynamics 1. Torque 2. Torque and Equilibrium 3. Center of Mass and Center of Gravity 4. Torque and angular acceleration 5. Rotational Kinetic energy 6. Angular

More information

Chapter 9. Rotational Dynamics

Chapter 9. Rotational Dynamics Chapter 9 Rotational Dynamics In pure translational motion, all points on an object travel on parallel paths. The most general motion is a combination of translation and rotation. 1) Torque Produces angular

More information

+ ] B A BA / t BA / n. B G BG / t BG / n. a = (5)(4) = 80 in./s. A G AG / t AG / n. ] + [48 in./s ]

+ ] B A BA / t BA / n. B G BG / t BG / n. a = (5)(4) = 80 in./s. A G AG / t AG / n. ] + [48 in./s ] PROLEM 15.113 3-in.-radius drum is rigidly attached to a 5-in.-radius drum as shown. One of the drums rolls without sliding on the surface shown, and a cord is wound around the other drum. Knowing that

More information

Deriving 1 DOF Equations of Motion Worked-Out Examples. MCE371: Vibrations. Prof. Richter. Department of Mechanical Engineering. Handout 3 Fall 2017

Deriving 1 DOF Equations of Motion Worked-Out Examples. MCE371: Vibrations. Prof. Richter. Department of Mechanical Engineering. Handout 3 Fall 2017 MCE371: Vibrations Prof. Richter Department of Mechanical Engineering Handout 3 Fall 2017 Masses with Rectilinear Motion Follow Palm, p.63, 67-72 and Sect.2.6. Refine your skill in drawing correct free

More information

Slide 1 / 133. Slide 2 / 133. Slide 3 / How many radians are subtended by a 0.10 m arc of a circle of radius 0.40 m?

Slide 1 / 133. Slide 2 / 133. Slide 3 / How many radians are subtended by a 0.10 m arc of a circle of radius 0.40 m? 1 How many radians are subtended by a 0.10 m arc of a circle of radius 0.40 m? Slide 1 / 133 2 How many degrees are subtended by a 0.10 m arc of a circle of radius of 0.40 m? Slide 2 / 133 3 A ball rotates

More information

Name: Date: Period: AP Physics C Rotational Motion HO19

Name: Date: Period: AP Physics C Rotational Motion HO19 1.) A wheel turns with constant acceleration 0.450 rad/s 2. (9-9) Rotational Motion H19 How much time does it take to reach an angular velocity of 8.00 rad/s, starting from rest? Through how many revolutions

More information

Slide 2 / 133. Slide 1 / 133. Slide 3 / 133. Slide 4 / 133. Slide 5 / 133. Slide 6 / 133

Slide 2 / 133. Slide 1 / 133. Slide 3 / 133. Slide 4 / 133. Slide 5 / 133. Slide 6 / 133 Slide 1 / 133 1 How many radians are subtended by a 0.10 m arc of a circle of radius 0.40 m? Slide 2 / 133 2 How many degrees are subtended by a 0.10 m arc of a circle of radius of 0.40 m? Slide 3 / 133

More information

STUDY GUIDE 4: Equilibrium, Angular Kinematics, and Dynamics

STUDY GUIDE 4: Equilibrium, Angular Kinematics, and Dynamics PH 1110 Term C11 STUDY GUIDE 4: Equilibrium, Angular Kinematics, and Dynamics Objectives 25. Define torque. Solve problems involving objects in static equilibrium. 26. Define angular displacement, angular

More information

Physics 1135 Version A

Physics 1135 Version A Physics 1135 Version A Spring 2017 Answer Sheet Solution Rec Sec E ini-test First Name: & Final Exam Remove this page from your exam when you begin. Write clearly in the space provided on this Answer Sheet

More information

CHAPTER 8 TEST REVIEW MARKSCHEME

CHAPTER 8 TEST REVIEW MARKSCHEME AP PHYSICS Name: Period: Date: 50 Multiple Choice 45 Single Response 5 Multi-Response Free Response 3 Short Free Response 2 Long Free Response MULTIPLE CHOICE DEVIL PHYSICS BADDEST CLASS ON CAMPUS AP EXAM

More information

PHYSICS 221 SPRING 2015

PHYSICS 221 SPRING 2015 PHYSICS 221 SPRING 2015 EXAM 2: April 2, 2015 8:15-10:15pm Name (printed): Recitation Instructor: Section # INSTRUCTIONS: This exam contains 25 multiple-choice questions plus 2 extra credit questions,

More information

Do not fill out the information below until instructed to do so! Name: Signature: Student ID: Section Number:

Do not fill out the information below until instructed to do so! Name: Signature: Student ID:   Section Number: Do not fill out the information below until instructed to do so! Name: Signature: Student ID: E-mail: Section Number: Formulae are provided on the last page. You may NOT use any other formula sheet. You

More information

Suggested Problems. Chapter 1

Suggested Problems. Chapter 1 Suggested Problems Ch1: 49, 51, 86, 89, 93, 95, 96, 102. Ch2: 9, 18, 20, 44, 51, 74, 75, 93. Ch3: 4, 14, 46, 54, 56, 75, 91, 80, 82, 83. Ch4: 15, 59, 60, 62. Ch5: 14, 52, 54, 65, 67, 83, 87, 88, 91, 93,

More information

Experiment 11. Moment of Inertia

Experiment 11. Moment of Inertia Experiment Moment of nertia A rigid body composed of concentric disks is constrained to rotate about its axis of symmetry. The moment of inertia is found by two methods and results are compared. n first

More information

PHYSICS 221 Fall 2016 EXAM 2: November 02, :15pm 10:15pm. Name (printed): Recitation Instructor: Section #:

PHYSICS 221 Fall 2016 EXAM 2: November 02, :15pm 10:15pm. Name (printed): Recitation Instructor: Section #: PHYSICS 221 Fall 2016 EXAM 2: November 02, 2016 8:15pm 10:15pm Name (printed): Recitation Instructor: Section #: INSTRUCTIONS: This exam contains 25 multiple-choice questions, plus 2 extra-credit questions,

More information

Webreview Torque and Rotation Practice Test

Webreview Torque and Rotation Practice Test Please do not write on test. ID A Webreview - 8.2 Torque and Rotation Practice Test Multiple Choice Identify the choice that best completes the statement or answers the question. 1. A 0.30-m-radius automobile

More information

APPLIED MATHEMATICS HIGHER LEVEL

APPLIED MATHEMATICS HIGHER LEVEL L.42 PRE-LEAVING CERTIFICATE EXAMINATION, 203 APPLIED MATHEMATICS HIGHER LEVEL TIME : 2½ HOURS Six questions to be answered. All questions carry equal marks. A Formulae and Tables booklet may be used during

More information

UNIVERSITY OF SASKATCHEWAN GE MECHANICS III MIDTERM EXAM FEBRUARY 13, 2008 A. Dolovich & H. Huenison A CLOSED BOOK EXAMINATION TIME: 2 HOURS

UNIVERSITY OF SASKATCHEWAN GE MECHANICS III MIDTERM EXAM FEBRUARY 13, 2008 A. Dolovich & H. Huenison A CLOSED BOOK EXAMINATION TIME: 2 HOURS UNIVERSITY OF SASKATCHEWAN GE 226.3 MECHANICS III MIDTERM EXAM FEBRUARY 13, 2008 A. Dolovich & H. Huenison A CLOSED BOOK EXAMINATION TIME: 2 HOURS LAST NAME (printed): FIRST NAME (printed): STUDENT NUMBER:

More information

PHYSICS 111 SPRING EXAM 2: March 6, 2018; 8:15-9:45 pm

PHYSICS 111 SPRING EXAM 2: March 6, 2018; 8:15-9:45 pm PHYSICS 111 SPRING 2018 EXAM 2: March 6, 2018; 8:15-9:45 pm Name (printed): Recitation Instructor: Section # INSTRUCTIONS: This exam contains 20 multiple-choice questions plus 1 extra credit question,

More information

Circular Motion Dynamics Concept Questions

Circular Motion Dynamics Concept Questions Circular Motion Dynamics Concept Questions Problem 1: A puck of mass m is moving in a circle at constant speed on a frictionless table as shown above. The puck is connected by a string to a suspended bob,

More information

JNTU World. Subject Code: R13110/R13

JNTU World. Subject Code: R13110/R13 Set No - 1 I B. Tech I Semester Regular Examinations Feb./Mar. - 2014 ENGINEERING MECHANICS (Common to CE, ME, CSE, PCE, IT, Chem E, Aero E, AME, Min E, PE, Metal E) Time: 3 hours Max. Marks: 70 Question

More information

Phys 106 Practice Problems Common Quiz 1 Spring 2003

Phys 106 Practice Problems Common Quiz 1 Spring 2003 Phys 106 Practice Problems Common Quiz 1 Spring 2003 1. For a wheel spinning with constant angular acceleration on an axis through its center, the ratio of the speed of a point on the rim to the speed

More information

Worksheet for Exploration 10.1: Constant Angular Velocity Equation

Worksheet for Exploration 10.1: Constant Angular Velocity Equation Worksheet for Exploration 10.1: Constant Angular Velocity Equation By now you have seen the equation: θ = θ 0 + ω 0 *t. Perhaps you have even derived it for yourself. But what does it really mean for the

More information

8.012 Physics I: Classical Mechanics Fall 2008

8.012 Physics I: Classical Mechanics Fall 2008 IT OpenCourseWare http://ocw.mit.edu 8.012 Physics I: Classical echanics Fall 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. ASSACHUSETTS INSTITUTE

More information