ECE-305: Fall 2016 Minority Carrier Diffusion Equation (MCDE)
|
|
- Aldous Cannon
- 5 years ago
- Views:
Transcription
1 ECE-305: Fall 2016 Minority Carrier Diffusion Equation (MCDE) Professor Peter Bermel Electrical and Computer Engineering Purdue University, West Lafayette, IN USA Pierret, Semiconductor Device Fundamentals (SDF) Chapter 3 (pp ) 1
2 minority carrier diffusion equation (hole continuity equation) p t d dx J px q G R L p (1D, generation by light) p t d dx qd p dp dx q G p L t p (low-level injection, no electric field) p t D p d 2 p dx 2 p t p G L (D p spatially uniform) 2
3 How to solve (some) Exam 2 problems Step 1: From material information (semiconductor, doping, etc.), calculate carrier densities, Fermi level, etc. Start with the majority carriers, =, =. Then get the other carrier from = Step 2: Use band-diagram to calculate potential profile, electric field, = /, or = /, and =, etc. For homogenous semiconductor with a battery attached, = /. Step 3: Decide if this is drift-related problem (resistivity, velocity, mobility, etc.), or a diffusion related problem (light turning on-off, etc.) Step 4A: For a drift-problem use = +. For, you may be given a number, or table, or diffusion coefficient, etc. Learn how to read such a table. Step 4B: For a diffusion problem, read carefully for clues to simplify the minority carrier equation. 9/21/2016 Bermel ECE 305 F16 3
4 How to solve equations Step 4B: Two general types of minority diffusion problem. i) Determine if electron or the hole is the minority carrier. ii) If holes are the minority carriers, write the equation: p t D p d 2 p dx 2 p t p G L iii) iv) If steady-state, drop the time-derivative. If transient, keep the time derivative. If spatially uniform, drop the diffusion term. Without light, drop the generation term. If the region is very short, drop the recombination term. Choose the solutions from the following table. Use the boundary conditions to complete solution. 9/21/2016 Bermel ECE 305 F16 4
5 How to solve equations Transient p t D p d 2 p dx 2 p t p G L Steady State =, 0 = d Δ + Δ solution Δ = G + Boundary condition for B: Concentration before light was turned on? 9/21/2016 solution Δ = + + If, Δ = + + BC to determine A and B: Concentration at leftmost and rightmost points Bermel ECE 305 F16 5
6 Example #1: Reading the problem Step 1: Determine carrier densities. a) The majority carrier is? b) the majority carrier concentration is? c) The minority carrier concentration is? d) How did they get the diffusion coefficient? e) Special words: uniformly doped. 9/21/2016 Bermel ECE 305 F16 6
7 Example #1: Solution P-type / equilibrium E C n 0 n 2 i 10 3 cm -3 p 0 p 0 n i e E i E F k B T e E i E F k B T E i E V p cm -3 E F E F E i 0.41 ev Steady-state, uniform generation, no spatial variation 7
8 Example #1: Reading the problem Step 3) What type of problems are we talking about voltage or light related? Step 4B ) Key words: steady-state, with light, uniform generation. ii) If I write p t D p d 2 p dx 2 p t p G L for MCDE, would I be right? iii) Which approximate equation should I choose: =, solution Δ = G + 0 = d Δ + Δ solution Δ = + + 8
9 Example #1: Solution P-type / out of equilibrium F p E i 0.41 ev E C E i n 0 n 2 i 10 3 cm -3 p 0 E V p cm -3 F n F p n» n n i e F n E i k B T e F n E i k B T F n E i 0.24 ev Steady-state, uniform generation, no spatial variation 9
10 Example #1: Solution n x nx G L t n 0 = d Δ + Δ Δ = + + n G L t n x 0 x Steady-state, uniform generation, no spatial variation 10
11 Example #2 Now turn off the light. Transient, no generation, no spatial variation iii) Which approximate equation should I choose? =, solution Δ = G + 0 = d Δ + Δ Solution: Δ = + + iv) What is my boundary condition: Just before, light was turned on for a long-time, before it is turned off. Δ (0 ) = = Δ (0 ) 11
12 Example #2 nt n nx n0e t/t n t 0 n t 0 t 12
13 Example #2 F p E i 0.41 ev nt» nt n i e F n t e t/t n 1010 e F n t F n E i k B T E i k B T t E i k B T ln10 4 k B T t t n E C E i E V F n F p transient, no generation, no spatial variation 13
14 Example #3: One sided Minority Diffusion Steady state, no generation/recombination Acceptor doped; sample short compared to diffusion length Metal contact n x', t 0 1 J n 1 dj n rn t q dx x a 0 N N N g N dn qnm E qd dx 2 d n 0 D N 2 dx 9/21/2016 Bermel ECE 305 F16 14
15 Example #3: One sided Minority Diffusion 0 DN 2 d n dx 2 n x', t 0 Metal contact n( x, t) C Dx' x a 0 x a, n( x ' a) 0 C Da x 0', n( x ' 0') C n( x, t) n( x 0') 1 9/21/2016 x ' a Bermel ECE 305 F16 x 15
16 Example #4 Steady-state, sample long compared to the diffusion length. No generation. n x 0 fixed cm -3 Step 3) What type of problems are we talking about? Step 4B ) Key words: steady-state, without light, long device p d ii) If I write 2 p D p p G for MCDE, would I be right? t dx 2 L t p iii) Which approximate equation should I choose: =, solution Δ = G + 0 = d Δ + Δ 16 solution Δ =
17 Example #4 nx n0 nx n0e x/l n L n D n t n << L x 0 nx 0 x x L 200 mm Steady-state, sample long compared to the diffusion length. 17
18 Example #4 Steady-state, sample is 5 micron long. No generation. nx cm -3 n x 5 mm 0 Which approximate equation should I choose: =, solution Δ = G + 0 = + solution Δ = + + or Δ = + + What are my boundary conditions? 18
19 Example #4 nx cm -3 n x L D 0 nx Ax B nx cm -3 nx n 0 1 x L L 0 n x 19
20 Example #5 Steady-state, sample is 30 micrometers long. No generation. nx cm -3 nx 30 mm 0 fixed n t D p d 2 n dx 2 t n G L 0 D p d 2 n dx 2 t n 0 1) Simplify the MCDE 2) Solve the MCDE 3) Deduce F p from Δp d 2 n dx 2 L n 28 mm n L n 0 L n º D n t n L 30 mm 20
21 Example #5 Steady-state, sample is 30 micrometers long. No generation. nx cm -3 nx 30 mm 0 fixed d 2 n dx 2 n L n 0 nx Ae x/l n Be x/l n 1) Simplify the MCDE 2) Solve the MCDE 3) Deduce F p from Δp n0 A B nl Ae L/L n Be L/L n 0 21
22 Example #5 nx n0 L n n x n 0 D n t n» L sinh éë L x / L n ù û sinh L / L n nx L 0 x x 0 x L Steady-state, sample neither long nor short compared to the diffusion length. 9/21/2016 Bermel ECE 305 F16 22
23 Spatially-dependent MCDE example summary Length scale Solution type Long ( ) Decaying exponentials Short ( ) Linear Intermediate ( ~ ) Hyperbolic functions Notes: is length of region where MCDE applies =,, is the diffusion length for carriers 23
ECE-305: Spring 2018 Exam 2 Review
ECE-305: Spring 018 Exam Review Pierret, Semiconductor Device Fundamentals (SDF) Chapter 3 (pp. 75-138) Chapter 5 (pp. 195-6) Professor Peter Bermel Electrical and Computer Engineering Purdue University,
More informationMinority Carrier Diffusion Equation (MCDE)
ECE-305: Spring 2015 Minority Carrier Diffusion Equation (MCDE) Professor Mark undstrom Electrical and Computer Engineering Purdue University, West afayette, IN USA lundstro@purdue.edu Pierret, Semiconductor
More informationECE-305: Spring Carrier Action: II. Pierret, Semiconductor Device Fundamentals (SDF) pp
ECE-305: Spring 015 Carrier Action: II Pierret, Semiconductor Device Fundamentals (SDF) pp. 89-104 Professor Mark Lundstrom Electrical and Computer Engineering Purdue University, West Lafayette, IN USA
More informationESE 372 / Spring 2013 / Lecture 5 Metal Oxide Semiconductor Field Effect Transistor
Metal Oxide Semiconductor Field Effect Transistor V G V G 1 Metal Oxide Semiconductor Field Effect Transistor We will need to understand how this current flows through Si What is electric current? 2 Back
More informationECE 305: Fall MOSFET Energy Bands
ECE 305: Fall 2016 MOSFET Energy Bands Professor Peter Bermel Electrical and Computer Engineering Purdue University, West Lafayette, IN USA pbermel@purdue.edu Pierret, Semiconductor Device Fundamentals
More informationEE3901 A2001. Semiconductor Devices. Exam 1
Name ECE Box # Problem Score Points 1 10 2 30 3 35 4 25 EE3901 A2001 Semiconductor Devices Exam 1 This is a closed book test! You are allowed one sheet (both sides) of notes. Note: Potentially useful reference
More informationGetting J e (x), J h (x), E(x), and p'(x), knowing n'(x) Solving the diffusion equation for n'(x) (using p-type example)
6.012 - Electronic Devices and Circuits Lecture 4 - Non-uniform Injection (Flow) Problems - Outline Announcements Handouts - 1. Lecture Outline and Summary; 2. Thermoelectrics Review Thermoelectricity:
More information( )! N D ( x) ) and equilibrium
ECE 66: SOLUTIONS: ECE 66 Homework Week 8 Mark Lundstrom March 7, 13 1) The doping profile for an n- type silicon wafer ( N D = 1 15 cm - 3 ) with a heavily doped thin layer at the surface (surface concentration,
More informationECE-305: Spring 2018 Final Exam Review
C-305: Spring 2018 Final xam Review Pierret, Semiconductor Device Fundamentals (SDF) Chapters 10 and 11 (pp. 371-385, 389-403) Professor Peter Bermel lectrical and Computer ngineering Purdue University,
More informationECE-305: Fall 2017 Metal Oxide Semiconductor Devices
C-305: Fall 2017 Metal Oxide Semiconductor Devices Pierret, Semiconductor Device Fundamentals (SDF) Chapters 15+16 (pp. 525-530, 563-599) Professor Peter Bermel lectrical and Computer ngineering Purdue
More informationSemiconductor Device Physics
1 Semiconductor Device Physics Lecture 3 http://zitompul.wordpress.com 2 0 1 3 Semiconductor Device Physics 2 Three primary types of carrier action occur inside a semiconductor: Drift: charged particle
More informationThe German University in Cairo. Faculty of Information Engineering & Technology Semiconductors (Elct 503) Electronics Department Fall 2014
The German University in Cairo th Electronics 5 Semester Faculty of Information Engineering & Technology Semiconductors (Elct 503) Electronics Department Fall 2014 Problem Set 3 1- a) Find the resistivity
More informationECE 340 Lecture 21 : P-N Junction II Class Outline:
ECE 340 Lecture 21 : P-N Junction II Class Outline: Contact Potential Equilibrium Fermi Levels Things you should know when you leave Key Questions What is the contact potential? Where does the transition
More informationLecture 15 - The pn Junction Diode (I) I-V Characteristics. November 1, 2005
6.012 - Microelectronic Devices and Circuits - Fall 2005 Lecture 15-1 Lecture 15 - The pn Junction Diode (I) I-V Characteristics November 1, 2005 Contents: 1. pn junction under bias 2. I-V characteristics
More informationCharge Carriers in Semiconductor
Charge Carriers in Semiconductor To understand PN junction s IV characteristics, it is important to understand charge carriers behavior in solids, how to modify carrier densities, and different mechanisms
More informationCarrier Recombination
Notes for ECE-606: Spring 013 Carrier Recombination Professor Mark Lundstrom Electrical and Computer Engineering Purdue University, West Lafayette, IN USA lundstro@purdue.edu /19/13 1 carrier recombination-generation
More informationQuiz #1 Practice Problem Set
Name: Student Number: ELEC 3908 Physical Electronics Quiz #1 Practice Problem Set? Minutes January 22, 2016 - No aids except a non-programmable calculator - All questions must be answered - All questions
More informationUniform excitation: applied field and optical generation. Non-uniform doping/excitation: diffusion, continuity
6.012 - Electronic Devices and Circuits Lecture 2 - Uniform Excitation; Non-uniform conditions Announcements Review Carrier concentrations in TE given the doping level What happens above and below room
More informationSemiconductor Physics and Devices
The pn Junction 1) Charge carriers crossing the junction. 3) Barrier potential Semiconductor Physics and Devices Chapter 8. The pn Junction Diode 2) Formation of positive and negative ions. 4) Formation
More informationECE 606 Homework Week 7 Mark Lundstrom Purdue University (revised 2/25/13) e E i! E T
ECE 606 Homework Week 7 Mark Lundstrom Purdue University (revised 2/25/13) 1) Consider an n- type semiconductor for which the only states in the bandgap are donor levels (i.e. ( E T = E D ). Begin with
More informationCarrier transport: Drift and Diffusion
. Carrier transport: Drift and INEL 5209 - Solid State Devices - Spring 2012 Manuel Toledo April 10, 2012 Manuel Toledo Transport 1/ 32 Outline...1 Drift Drift current Mobility Resistivity Resistance Hall
More information6.012 Electronic Devices and Circuits
Page 1 of 1 YOUR NAME Department of Electrical Engineering and Computer Science Massachusetts Institute of Technology 6.12 Electronic Devices and Circuits Exam No. 1 Wednesday, October 7, 29 7:3 to 9:3
More informationSpring Semester 2012 Final Exam
Spring Semester 2012 Final Exam Note: Show your work, underline results, and always show units. Official exam time: 2.0 hours; an extension of at least 1.0 hour will be granted to anyone. Materials parameters
More informationIdeal Diode Equation II + Intro to Solar Cells
ECE-35: Spring 15 Ideal Diode Equation II + Intro to Solar Cells Professor Mark Lundstrom Electrical and Computer Engineering Purdue University, West Lafayette, IN USA lundstro@purdue.edu Pierret, Semiconductor
More informationECE-305: Fall 2017 MOS Capacitors and Transistors
ECE-305: Fall 2017 MOS Capacitors and Transistors Pierret, Semiconductor Device Fundamentals (SDF) Chapters 15+16 (pp. 525-530, 563-599) Professor Peter Bermel Electrical and Computer Engineering Purdue
More informationSolid State Physics SEMICONDUCTORS - IV. Lecture 25. A.H. Harker. Physics and Astronomy UCL
Solid State Physics SEMICONDUCTORS - IV Lecture 25 A.H. Harker Physics and Astronomy UCL 9.9 Carrier diffusion and recombination Suppose we have a p-type semiconductor, i.e. n h >> n e. (1) Create a local
More informationThis is the 15th lecture of this course in which we begin a new topic, Excess Carriers. This topic will be covered in two lectures.
Solid State Devices Dr. S. Karmalkar Department of Electronics and Communication Engineering Indian Institute of Technology, Madras Lecture - 15 Excess Carriers This is the 15th lecture of this course
More informationSession 5: Solid State Physics. Charge Mobility Drift Diffusion Recombination-Generation
Session 5: Solid State Physics Charge Mobility Drift Diffusion Recombination-Generation 1 Outline A B C D E F G H I J 2 Mobile Charge Carriers in Semiconductors Three primary types of carrier action occur
More informationn N D n p = n i p N A
Summary of electron and hole concentration in semiconductors Intrinsic semiconductor: E G n kt i = pi = N e 2 0 Donor-doped semiconductor: n N D where N D is the concentration of donor impurity Acceptor-doped
More informationSample Exam # 2 ECEN 3320 Fall 2013 Semiconductor Devices October 28, 2013 Due November 4, 2013
Sample Exam # 2 ECEN 3320 Fall 203 Semiconductor Devices October 28, 203 Due November 4, 203. Below is the capacitance-voltage curve measured from a Schottky contact made on GaAs at T 300 K. Figure : Capacitance
More informationCLASS 3&4. BJT currents, parameters and circuit configurations
CLASS 3&4 BJT currents, parameters and circuit configurations I E =I Ep +I En I C =I Cp +I Cn I B =I BB +I En -I Cn I BB =I Ep -I Cp I E = I B + I C I En = current produced by the electrons injected from
More informationBipolar Junction Transistors: Solving Ebers-Moll Problems
C 305: Fall 016 ipolar Junction Transistors: Solving bers-moll Problems Professor Peter ermel lectrical and Computer ngineering Purdue University, West Lafayette, N USA pbermel@purdue.edu Pierret, Semiconductor
More informationThe 5 basic equations of semiconductor device physics: We will in general be faced with finding 5 quantities:
6.012 - Electronic Devices and Circuits Solving the 5 basic equations - 2/12/08 Version The 5 basic equations of semiconductor device physics: We will in general be faced with finding 5 quantities: n(x,t),
More informationEnergy Bands & Carrier Densities
Notes for ECE-606: Spring 03 Energy Bands & Carrier Densities Professor Mark Lundstrom Electrical and Computer Engineering Purdue University, West Lafayette, IN USA lundstro@purdue.edu /7/3 Key topics
More informationCarriers Concentration and Current in Semiconductors
Carriers Concentration and Current in Semiconductors Carrier Transport Two driving forces for carrier transport: electric field and spatial variation of the carrier concentration. Both driving forces lead
More informationUNIVERSITY OF CALIFORNIA College of Engineering Department of Electrical Engineering and Computer Sciences. EECS 130 Professor Ali Javey Fall 2006
UNIVERSITY OF CALIFORNIA College of Engineering Department of Electrical Engineering and Computer Sciences EECS 130 Professor Ali Javey Fall 2006 Midterm I Name: Closed book. One sheet of notes is allowed.
More informationLecture 27: Introduction to Bipolar Transistors
NCN www.nanohub.org ECE606: Solid State Devices Lecture 27: Introduction to ipolar Transistors Muhammad Ashraful Alam alam@purdue.edu Alam ECE 606 S09 1 ackground E C E C ase! Point contact Germanium transistor
More informationV BI. H. Föll: kiel.de/matwis/amat/semi_en/kap_2/backbone/r2_2_4.html. different electrochemical potentials (i.e.
Consider the the band diagram for a homojunction, formed when two bits of the same type of semicondutor (e.g. Si) are doped p and ntype and then brought into contact. Electrons in the two bits have different
More informationLecture 1. OUTLINE Basic Semiconductor Physics. Reading: Chapter 2.1. Semiconductors Intrinsic (undoped) silicon Doping Carrier concentrations
Lecture 1 OUTLINE Basic Semiconductor Physics Semiconductors Intrinsic (undoped) silicon Doping Carrier concentrations Reading: Chapter 2.1 EE105 Fall 2007 Lecture 1, Slide 1 What is a Semiconductor? Low
More informationElectronic Devices and Circuits Lecture 5 - p-n Junction Injection and Flow - Outline
6.012 - Electronic Devices and Circuits Lecture 5 - p-n Junction Injection and Flow - Outline Review Depletion approimation for an abrupt p-n junction Depletion charge storage and depletion capacitance
More informationcollisions of electrons. In semiconductor, in certain temperature ranges the conductivity increases rapidly by increasing temperature
1.9. Temperature Dependence of Semiconductor Conductivity Such dependence is one most important in semiconductor. In metals, Conductivity decreases by increasing temperature due to greater frequency of
More informationCurrent mechanisms Exam January 27, 2012
Current mechanisms Exam January 27, 2012 There are four mechanisms that typically cause currents to flow: thermionic emission, diffusion, drift, and tunneling. Explain briefly which kind of current mechanisms
More informationSemiconductor Junctions
8 Semiconductor Junctions Almost all solar cells contain junctions between different materials of different doping. Since these junctions are crucial to the operation of the solar cell, we will discuss
More informationEE105 - Fall 2006 Microelectronic Devices and Circuits
EE105 - Fall 2006 Microelectronic Devices and Circuits Prof. Jan M. Rabaey (jan@eecs) Lecture 21: Bipolar Junction Transistor Administrative Midterm Th 6:30-8pm in Sibley Auditorium Covering everything
More informationSemiconductors CHAPTER 3. Introduction The pn Junction with an Applied Voltage Intrinsic Semiconductors 136
CHAPTER 3 Semiconductors Introduction 135 3.1 Intrinsic Semiconductors 136 3.2 Doped Semiconductors 139 3.3 Current Flow in Semiconductors 142 3.4 The pn Junction 148 3.5 The pn Junction with an Applied
More informationPHYS208 p-n junction. January 15, 2010
1 PHYS208 p-n junction January 15, 2010 List of topics (1) Density of states Fermi-Dirac distribution Law of mass action Doped semiconductors Dopinglevel p-n-junctions 1 Intrinsic semiconductors List of
More informationFor the following statements, mark ( ) for true statement and (X) for wrong statement and correct it.
Benha University Faculty of Engineering Shoubra Electrical Engineering Department First Year communications. Answer all the following questions Illustrate your answers with sketches when necessary. The
More informationSOLUTIONS: ECE 606 Homework Week 10 Mark Lundstrom. Purdue University. (Revised 3/29/13)
ECE- 66 SOLUTIOS: ECE 66 Homework Week 1 Mark Lundstrom (Revised 3/9/13) 1) In a forward- biased P junction under low- injection conditions, the QFL s are aroximately flat from the majority carrier region
More informationSemiconductor Devices and Circuits Fall Midterm Exam. Instructor: Dr. Dietmar Knipp, Professor of Electrical Engineering. Name: Mat. -Nr.
Semiconductor Devices and Circuits Fall 2003 Midterm Exam Instructor: Dr. Dietmar Knipp, Professor of Electrical Engineering Name: Mat. -Nr.: Guidelines: Duration of the Midterm: 1 hour The exam is a closed
More informationSemiconductor Physics
Semiconductor Physics Motivation Is it possible that there might be current flowing in a conductor (or a semiconductor) even when there is no potential difference supplied across its ends? Look at the
More informationRecitation 17: BJT-Basic Operation in FAR
Recitation 17: BJT-Basic Operation in FAR BJT stands for Bipolar Junction Transistor 1. Can be thought of as two p-n junctions back to back, you can have pnp or npn. In analogy to MOSFET small current
More informationDue to the quantum nature of electrons, one energy state can be occupied only by one electron.
In crystalline solids, not all values of the electron energy are possible. The allowed intervals of energy are called allowed bands (shown as blue and chess-board blue). The forbidden intervals are called
More informationChapter 7. The pn Junction
Chapter 7 The pn Junction Chapter 7 PN Junction PN junction can be fabricated by implanting or diffusing donors into a P-type substrate such that a layer of semiconductor is converted into N type. Converting
More informationSession 6: Solid State Physics. Diode
Session 6: Solid State Physics Diode 1 Outline A B C D E F G H I J 2 Definitions / Assumptions Homojunction: the junction is between two regions of the same material Heterojunction: the junction is between
More informationSemiconductor Physics fall 2012 problems
Semiconductor Physics fall 2012 problems 1. An n-type sample of silicon has a uniform density N D = 10 16 atoms cm -3 of arsenic, and a p-type silicon sample has N A = 10 15 atoms cm -3 of boron. For each
More informationSection 12: Intro to Devices
Section 12: Intro to Devices Extensive reading materials on reserve, including Robert F. Pierret, Semiconductor Device Fundamentals Bond Model of Electrons and Holes Si Si Si Si Si Si Si Si Si Silicon
More informationLecture-4 Junction Diode Characteristics
1 Lecture-4 Junction Diode Characteristics Part-II Q: Aluminum is alloyed into n-type Si sample (N D = 10 16 cm 3 ) forming an abrupt junction of circular cross-section, with an diameter of 0.02 in. Assume
More informationCarrier Action: Motion, Recombination and Generation. What happens after we figure out how many electrons and holes are in the semiconductor?
Carrier Action: Motion, Recombination and Generation. What happens after we figure out how many electrons and holes are in the semiconductor? 1 Carrier Motion I Described by 2 concepts: Conductivity: σ
More informationECE 250 Electronic Devices 1. Electronic Device Modeling
ECE 250 Electronic Devices 1 ECE 250 Electronic Device Modeling ECE 250 Electronic Devices 2 Introduction to Semiconductor Physics You should really take a semiconductor device physics course. We can only
More informationPHYS208 P-N Junction. Olav Torheim. May 30, 2007
1 PHYS208 P-N Junction Olav Torheim May 30, 2007 1 Intrinsic semiconductors The lower end of the conduction band is a parabola, just like in the quadratic free electron case (E = h2 k 2 2m ). The density
More informationEE105 Fall 2015 Microelectronic Devices and Circuits: Semiconductor Fabrication and PN Junctions
EE105 Fall 2015 Microelectronic Devices and Circuits: Semiconductor Fabrication and PN Junctions Prof. Ming C. Wu wu@eecs.berkeley.edu 511 Sutardja Dai Hall (SDH) 1 pn Junction p-type semiconductor in
More informationECE 142: Electronic Circuits Lecture 3: Semiconductors
Faculty of Engineering ECE 142: Electronic Circuits Lecture 3: Semiconductors Agenda Intrinsic Semiconductors Extrinsic Semiconductors N-type P-type Carrier Transport Drift Diffusion Semiconductors A semiconductor
More informationChapter 2. Electronics I - Semiconductors
Chapter 2 Electronics I - Semiconductors Fall 2017 talarico@gonzaga.edu 1 Charged Particles The operation of all electronic devices is based on controlling the flow of charged particles There are two type
More informationFinal Examination EE 130 December 16, 1997 Time allotted: 180 minutes
Final Examination EE 130 December 16, 1997 Time allotted: 180 minutes Problem 1: Semiconductor Fundamentals [30 points] A uniformly doped silicon sample of length 100µm and cross-sectional area 100µm 2
More informationSolar Cell Physics: recombination and generation
NCN Summer School: July 2011 Solar Cell Physics: recombination and generation Prof. Mark Lundstrom lundstro@purdue.edu Electrical and Computer Engineering Purdue University West Lafayette, Indiana USA
More informationECE 305 Fall Final Exam (Exam 5) Wednesday, December 13, 2017
NAME: PUID: ECE 305 Fall 017 Final Exam (Exam 5) Wednesday, December 13, 017 This is a closed book exam. You may use a calculator and the formula sheet at the end of this exam. Following the ECE policy,
More informationSemiconductor Physics. Lecture 3
Semiconductor Physics Lecture 3 Intrinsic carrier density Intrinsic carrier density Law of mass action Valid also if we add an impurity which either donates extra electrons or holes the number of carriers
More informationjunctions produce nonlinear current voltage characteristics which can be exploited
Chapter 6 P-N DODES Junctions between n-and p-type semiconductors are extremely important foravariety of devices. Diodes based on p-n junctions produce nonlinear current voltage characteristics which can
More informationexp Compared to the values obtained in Example 2.1, we can see that the intrinsic carrier concentration in Ge at T = 300 K is 2.
.1 (a) k =8.617 10 5 ev/k n i (T = 300 K) = 1.66 10 15 (300 K) 3/ 66 ev exp (8.617 10 5 ev/k) (300 K) =.465 10 13 cm 3 n i (T = 600 K) = 1.66 10 15 (600 K) 3/ 66 ev exp (8.617 10 5 ev/k) (600 K) = 4.14
More informationSection 12: Intro to Devices
Section 12: Intro to Devices Extensive reading materials on reserve, including Robert F. Pierret, Semiconductor Device Fundamentals EE143 Ali Javey Bond Model of Electrons and Holes Si Si Si Si Si Si Si
More informationFundamentals of Semiconductor Physics
Fall 2007 Fundamentals of Semiconductor Physics 万 歆 Zhejiang Institute of Modern Physics xinwan@zimp.zju.edu.cn http://zimp.zju.edu.cn/~xinwan/ Transistor technology evokes new physics The objective of
More informationLecture 8. Equations of State, Equilibrium and Einstein Relationships and Generation/Recombination
Lecture 8 Equations of State, Equilibrium and Einstein Relationships and Generation/Recombination Reading: (Cont d) Notes and Anderson 2 sections 3.4-3.11 Energy Equilibrium Concept Consider a non-uniformly
More informationLecture 9 - Carrier Drift and Diffusion (cont.), Carrier Flow. September 24, 2001
6.720J/3.43J - Integrated Microelectronic Devices - Fall 2001 Lecture 9-1 Lecture 9 - Carrier Drift and Diffusion (cont.), Carrier Flow September 24, 2001 Contents: 1. Quasi-Fermi levels 2. Continuity
More information16EC401 BASIC ELECTRONIC DEVICES UNIT I PN JUNCTION DIODE. Energy Band Diagram of Conductor, Insulator and Semiconductor:
16EC401 BASIC ELECTRONIC DEVICES UNIT I PN JUNCTION DIODE Energy bands in Intrinsic and Extrinsic silicon: Energy Band Diagram of Conductor, Insulator and Semiconductor: 1 2 Carrier transport: Any motion
More information1 Name: Student number: DEPARTMENT OF PHYSICS AND PHYSICAL OCEANOGRAPHY MEMORIAL UNIVERSITY OF NEWFOUNDLAND. Fall :00-11:00
1 Name: DEPARTMENT OF PHYSICS AND PHYSICAL OCEANOGRAPHY MEMORIAL UNIVERSITY OF NEWFOUNDLAND Final Exam Physics 3000 December 11, 2012 Fall 2012 9:00-11:00 INSTRUCTIONS: 1. Answer all seven (7) questions.
More informationLecture 8 - Carrier Drift and Diffusion (cont.) September 21, 2001
6.720J/3.43J - Integrated Microelectronic Devices - Fall 2001 Lecture 8-1 Lecture 8 - Carrier Drift and Diffusion (cont.) September 21, 2001 Contents: 1. Non-uniformly doped semiconductor in thermal equilibrium
More informationA Simplified, Analytical, One-Dimensional Model for Saturation Operation of the Bipolar Transistor
82 A Simplified, Analytical, One-Dimensional Model for Saturation Operation of the Bipolar Transistor G.T. Wright and P.P. Frangos Electronic and Electrical Engineering Department, University of Birmingham,
More informationLecture 15: Optoelectronic devices: Introduction
Lecture 15: Optoelectronic devices: Introduction Contents 1 Optical absorption 1 1.1 Absorption coefficient....................... 2 2 Optical recombination 5 3 Recombination and carrier lifetime 6 3.1
More informationUNIVERSITY OF CALIFORNIA College of Engineering Department of Electrical Engineering and Computer Sciences. Professor Chenming Hu.
UNIVERSITY OF CALIFORNIA College of Engineering Department of Electrical Engineering and Computer Sciences EECS 130 Spring 2009 Professor Chenming Hu Midterm I Name: Closed book. One sheet of notes is
More informationElectrical Resistance
Electrical Resistance I + V _ W Material with resistivity ρ t L Resistance R V I = L ρ Wt (Unit: ohms) where ρ is the electrical resistivity 1 Adding parts/billion to parts/thousand of dopants to pure
More informationLecture 17 The Bipolar Junction Transistor (I) Forward Active Regime
Lecture 17 The Bipolar Junction Transistor (I) Forward Active Regime Outline The Bipolar Junction Transistor (BJT): structure and basic operation I V characteristics in forward active regime Reading Assignment:
More informationLecture 7 - Carrier Drift and Diffusion (cont.) February 20, Non-uniformly doped semiconductor in thermal equilibrium
6.720J/3.43J - Integrated Microelectronic Devices - Spring 2007 Lecture 7-1 Lecture 7 - Carrier Drift and Diffusion (cont.) February 20, 2007 Contents: 1. Non-uniformly doped semiconductor in thermal equilibrium
More informationLecture 3 Semiconductor Physics (II) Carrier Transport
Lecture 3 Semiconductor Physics (II) Carrier Transport Thermal Motion Carrier Drift Carrier Diffusion Outline Reading Assignment: Howe and Sodini; Chapter 2, Sect. 2.4-2.6 6.012 Spring 2009 Lecture 3 1
More informationVariation of Energy Bands with Alloy Composition E
Variation of Energy Bands with Alloy Composition E 3.0 E.8.6 L 0.3eV Al x GaAs AlAs 1- xas 1.43eV.16eV X k.4 L. X.0 X 1.8 L 1.6 1.4 0 0. 0.4 0.6 X 0.8 1 1 Carriers in intrinsic Semiconductors Ec 4º 1º
More informationL5: Surface Recombination, Continuity Equation & Extended Topics tanford University
L5: Surface Recombination, Continuity Equation & Extended Topics EE 216 : Aneesh Nainani 1 Announcements Project Select topic by Jan 29 (Tuesday) 9 topics, maximum 4 students per topic Quiz Thursday (Jan
More informationExtensive reading materials on reserve, including
Section 12: Intro to Devices Extensive reading materials on reserve, including Robert F. Pierret, Semiconductor Device Fundamentals EE143 Ali Javey Bond Model of Electrons and Holes Si Si Si Si Si Si Si
More informationPN Junction
P Junction 2017-05-04 Definition Power Electronics = semiconductor switches are used Analogue amplifier = high power loss 250 200 u x 150 100 u Udc i 50 0 0 50 100 150 200 250 300 350 400 i,u dc i,u u
More informationNumerical Example: Carrier Concentrations
2 Numerical ample: Carrier Concentrations Donor concentration: N d = 10 15 cm -3 Thermal equilibrium electron concentration: n o N d = 10 15 cm 3 Thermal equilibrium hole concentration: 2 2 p o = n i no
More informationDiodes. anode. cathode. cut-off. Can be approximated by a piecewise-linear-like characteristic. Lecture 9-1
Diodes mplest nonlinear circuit element Basic operation sets the foundation for Bipolar Junction Transistors (BJTs) Also present in Field Effect Transistors (FETs) Ideal diode characteristic anode cathode
More informationECE 440 Lecture 12 : Diffusion of Carriers Class Outline:
ECE 440 Lecture 12 : Diffusion of Carriers Class Outline: Band Bending Diffusion Processes Diffusion and Drift of Carriers Things you should know when you leave Key Questions How do I calculate kinetic
More informationMidterm I - Solutions
UNIVERSITY OF CALIFORNIA College of Engineering Department of Electrical Engineering and Computer Sciences EECS 130 Spring 2008 Professor Chenming Hu Midterm I - Solutions Name: SID: Grad/Undergrad: Closed
More informationECE 440 Lecture 28 : P-N Junction II Class Outline:
ECE 440 Lecture 28 : P-N Junction II Class Outline: Contact Potential Equilibrium Fermi Levels Things you should know when you leave Key Questions What is the contact potential? Where does the transition
More informationIntroduction to Power Semiconductor Devices
ECE442 Power Semiconductor Devices and Integrated Circuits Introduction to Power Semiconductor Devices Zheng Yang (ERF 3017, email: yangzhen@uic.edu) Power Semiconductor Devices Applications System Ratings
More informationMotion and Recombination of Electrons and Holes
Chater Motion and Recombination of Electrons and Holes OBJECTIVES. Understand how the electrons and holes resond to an electric field (drift).. Understand how the electrons and holes resond to a gradient
More informationLecture 20 - p-n Junction (cont.) October 21, Non-ideal and second-order effects
6.70J/3.43J - Integrated Microelectronic Devices - Fall 00 Lecture 0-1 Lecture 0 - p-n Junction (cont.) October 1, 00 Contents: 1. Non-ideal and second-order effects Reading assignment: del Alamo, Ch.
More informationB12: Semiconductor Devices
B12: Semiconductor Devices Example Sheet 2: Solutions Question 1 To get from eq. (5.70) of the notes to the expression given in the examples sheet, we simply invoke the relations n 0 p 0, n 0 n 0. In this
More informationSolid State Electronics. Final Examination
The University of Toledo EECS:4400/5400/7400 Solid State Electronic Section elssf08fs.fm - 1 Solid State Electronics Final Examination Problems Points 1. 1. 14 3. 14 Total 40 Was the exam fair? yes no
More informationSchottky Rectifiers Zheng Yang (ERF 3017,
ECE442 Power Semiconductor Devices and Integrated Circuits Schottky Rectifiers Zheng Yang (ERF 3017, email: yangzhen@uic.edu) Power Schottky Rectifier Structure 2 Metal-Semiconductor Contact The work function
More informationForward-Active Terminal Currents
Forward-Active Terminal Currents Collector current: (electron diffusion current density) x (emitter area) diff J n AE qd n n po A E V E V th ------------------------------ e W (why minus sign? is by def.
More informationELEC 3908, Physical Electronics, Lecture 18. The Early Effect, Breakdown and Self-Heating
ELEC 3908, Physical Electronics, Lecture 18 The Early Effect, Breakdown and Self-Heating Lecture Outline Previous 2 lectures analyzed fundamental static (dc) carrier transport in the bipolar transistor
More information