Titration of HCl with Sodium Hydroxide
|
|
- Eunice Thomas
- 5 years ago
- Views:
Transcription
1 Titration of HCl with Sodium Hydroxide Lab Report for the Subject of Advanced Chemistry Anon Durongpisitkul, Karis Katekovit, Varun Saketharam,Thanon Thamvorapol, Chanon Anektanasup- January 28,
2 Introduction Titration is a process used by chemists to determine the concentration of a particular acid or base solution. The reaction process is typically an acid reacting with a hydroxide base producing Salt and Water. A ph indicator can be used to tell us when the reaction has completely neutralized. All the acid in the reaction is consumed and there is no excess base from the reaction. This is called the equivalence point. We can use this equivalence point to determine the concentration of the acid via calculations. The goal of this experiment is to get as close as possible to the equivalence point so that our acid concentration will be as close to the true value as possible. 2
3 Instructions 1. Record the molarity of the sodium hydroxide solution on the data sheet 2. Obtain about 100 ml of the Sodium Hydroxide solution in a clean beaker. This should be enough for the initial cleaning of your buret and for your first 3 trials. 3. Clean your buret: Add about 5 ml of the base solution from the beaker to the buret (use a funnel to pour). Move the funnel around while adding to ensure the sides of the buret are coated with base. Alternatively, you can remove the buret with the 5 ml of titrant form the buret stand and carefully tilt and rotate to coat all interior surfaces with the titrant. Drain the solution through the stopcock into a waste beaker. Repeat this rinse with a second 5 ml portion of the base. 4. Pour more of the sodium hydroxide solution into the buret until it is near the 0.00 ml mark. Open the stopcock to allow several drops to rinse through the tip of the buret. This should eliminate any air bubbles in the buret tip. Record your initial buret reading on the data sheet for trial 1 (the volume does not need to be exactly 0.00 ml). 5. Draw 10 ml of the acid solution into the volumetric pipet and transfer this solution into an Erlenmeyer flask. Add 2-3 drops of phenolphthalein to the acid solution in the flask. 6. Place the flask under the buret and start adding the base solution the the flask. One person must continually swirl the flask while the other person controls the stopcock. Slow down once the solution starts to turn pink. Add one drop at a time until a light pink color stays for 30 seconds. 7. Record and wash the flask. 8. Repeat until you get less than 1.0% difference. 3
4 Discussion 1. Why did the solution turn out as different shades of pink? The reason was most likely due to the amount of base added during the titration. More base meant a darker pink solution. Frankly speaking, it was due to the imprecise nature of experiments. 4
5 Post-lab Questions 1. How would it affect your results if you used a beaker with residual water in it to measure out your standardized sodium hydroxide solution? The HCl will be used more than normal because the water will already partially neutralize the acid (decreasing the M). Thus the molar of the acid will be greater than actual value. 2. How would it affect you results if you used a wet Erlenmeyer flask instead of a dry one when transferring your acid solution from the volumetric pipette? The NaOH will be used less than normal because the water will already partially neutralize the acid (decreasing the M). Thus the molar of the acid will be less than actual value. 3. How do you tell if you have exceeded the equivalence point in your titration? When the solution stops changing the color it means that the solution has gone pass the indicator range (which is too basic to be equivalent) 4. Vinegar is a solution of acetic acid (CH3COOH) in water. For quality control purposes, it can be titrated using a sodium hydroxide to assure a specific % composition. If ml of acetic acid is titrated with 9.08 ml of a standardized M sodium hydroxide solution, what is the molarity of the vinegar? Molarity = Moles/Volume of solution. Moles = Molarity x Volume of solution Moles = Moles/L x L = Moles NaOH All In Moles Molarity = Moles/ Volume of solution Molarity of CH3COOH = Mol CH3COOH/ L = M of Vinegar 5
6 Conclusion 10 ml of a 0.09 M concentration HCL is able to titrate 9 ml of a 1 M NaOH solution 6
7 7
Experiment #7. Titration of Vinegar
Experiment #7. Titration of Vinegar Goals 1. To determine the mass percent of acetic acid in a solution via titration. 2. To master the technique of titration. Introduction Vinegar is a common household
More informationCHM111 Lab Titration of Vinegar Grading Rubric
Name Team Name CHM111 Lab Titration of Vinegar Grading Rubric Criteria Points possible Points earned Lab Performance Printed lab handout and rubric was brought to lab 3 Safety and proper waste disposal
More informationTRATION: ANALYSIS OF VINE
Experiment 10 Name: 22 Ti TRATION: ANALYSIS OF VINE 31 Ga R In this experiment, you will learn the concept and technique of titration. You will determine the concentration of acetic acid in commercial
More informationChemical Reactions: Titrations
1 Chemical Reactions: Titrations ORGANIZATION Mode: laboratory work, work in pairs Grading: lab notes, lab performance (titration accuracy), and post-lab report Safety: goggles, lab coat, closed-toe shoes,
More information+ H 2 O Equation 1. + NaOH CO 2 Na
Experiment # 5 VINEGAR: AN FDA INVESTIGATION Objective In this experiment, you will play the role of an FDA analytical chemist, You will verify whether a vinegar manufacturer's quality control lab remains
More informationExperiment 20: Analysis of Vinegar. Materials:
Experiment 20: Analysis of Vinegar Materials: graduated cylinder 6 M NaOH: Dilute Sodium Hydroxide 1000 ml Florence Flask & stopper KHC 8 H 4 O 4 : Potassium Hydrogen Phthalate (KHP) 125 ml Erlenmeyer
More informationIn this laboratory exercise we will determine the percentage Acetic Acid (CH 3 CO 2 H) in Vinegar.
The titration of Acetic Acid in Vinegar In this laboratory exercise we will determine the percentage Acetic Acid (CH CO H) in Vinegar. We will do this by Titrating the Acetic Acid present with a Strong
More informationTitrations Worksheet and Lab
Titrations Worksheet and Lab Vocabulary 1. Buret: a piece of glassware used for dispensing accurate volumes, generally reads to two places of decimal. 2. Titrant: the substance of known concentration added
More informationAcid Base Titration Experiment ACID - BASE TITRATION LAB
ACID - BASE TITRATION LAB MATERIALS and CHEMICALS Burette 50 ml Burette clamp Ring stand Stirring rod Plastic funnel Beakers (50 ml, 100 ml, 400 ml) Graduated cylinder (25 ml, 50 ml) 0.10 M NaOH 0.10 M
More informationLearn to do quantitative titration reactions. Observe the mole ratios of several simple chemical reactions.
CHAPTER 6 Stoichiometry of Reactions in Solution Objectives The objectives of this laboratory are to: Learn to do quantitative titration reactions. Observe the mole ratios of several simple chemical reactions.
More informationUpon completion of this lab, the student will be able to:
1 Learning Outcomes EXPERIMENT 30A7: VINEGAR TITRATION Upon completion of this lab, the student will be able to: 1) Measure the amount of acetic acid in a solution of vinegar Introduction The molar concentration
More informationAcid-Base Titration Acetic Acid Content of Vinegar
Acid-Base Titration Acetic Acid Content of Vinegar Prelab Assignment Read the entire lab. Write an objective and any hazards associated with this lab in your laboratory notebook. On a separate sheet of
More information2 burets (50 ml) Standard solution of NaOH (0.600 M) Phenolphthalein indicator
Name: \[-[L Percentage of Acetic Acid In Vinegar Lab 4-5 INTRODUCTION: The quality of acid in a sample of vinegar may be found by titrating the sample against a standard basic solution. ost commercial
More informationChemistry 143 Acid Base Titration Dr. Caddell. Titrating Acid
Titrating Acid In this lab you will first determine the concentration of sodium hydroxide in a stock solution that you prepare. You will then use that stock sodium hydroxide solution to titrate a solution
More informationMolarity of Acetic Acid in Vinegar A Titration Experiment
Molarity of Acetic Acid in Vinegar A Titration Experiment Introduction Vinegar is prepared commercially in two steps, both requiring microorganisms. The first step is the production of ethyl alcohol, C
More informationExperiment 7: ACID-BASE TITRATION: STANDARDIZATION OF A SOLUTION
Experiment 7: ACID-BASE TITRATION: STANDARDIZATION OF A SOLUTION Purpose: Determine molarity of a solution of unknown concentration by performing acid-base titrations Performance Goals: Apply the concepts
More informationCHM 130 Acid-Base Titration Molarity of Acetic Acid in Vinegar
CHM 130 Acid-Base Titration Molarity of Acetic Acid in Vinegar INTRODUCTION One of the most important techniques for chemical analysis is titration to an equivalence point. To illustrate this procedure,
More informationAcid-Base Titration. M M V a
Acid-Base Titration Pre-Lab Discussion In the chemistry laboratory, it is sometimes necessary to experimentally determine the concentration of an acid solution or a base solution. A procedure for making
More informationTo see how this data can be used, follow the titration of hydrofluoric acid against sodium hydroxide:
Weak Acid Titration v010516 You are encouraged to carefully read the following sections in Tro (3 rd ed.) to prepare for this experiment: Sec 4.8, pp 168-174 (Acid/Base Titrations), Sec 16.4, pp 769-783
More informationChemistry 143 Experiment #11 Acid Base Titration Dr. Caddell. Titrating Acid
Titrating Acid In this lab you will first determine the concentration of sodium hydroxide in a stock solution that you prepare. You will then use that stock sodium hydroxide solution to titrate a solution
More informationNOTE: YOU WILL BE USING THIS SOLUTION IN BOTH, THIS EXPERIMENT AND EXP 12B. IF YOU WASTE THE SOLUTION YOU MAY RUN OUT BEFORE YOU HAVE FINISHED EXP 12B
EXPERIMENT 12 A: STANDARDIZATION OF A SODIUM HYDROXIDE SOLUTION OBJECTIVE: Sodium hydroxide solution of about 0.2 M is prepared in order to be used in Exp 12B. The solution is then standardized, that is,
More informationEXPERIMENT #8 Acid-Base I: Titration Techniques
EXPERIMENT #8 Acid-Base I: Titration Techniques OBJECTIVES: Dispense a precise volume of a solution with a buret Titrate a known volume of acid solution with a standard solution of base Reach a proper
More informationTitration with an Acid and a Base
Skills Practice Titration with an Acid and a Base Titration is a process in which you determine the concentration of a solution by measuring what volume of that solution is needed to react completely with
More informationNEUTRALIZATION TITRATION-2 TITRATION OF AN ANTACID (Exp. 4)
Objective NEUTRALIZATION TITRATION-2 TITRATION OF AN ANTACID (Exp. 4) The aim of this experiment is to carry out titration of antacid tablets and to determine acetic acid content of vinegar. a) Titration
More informationExperiment 10 Acid-Base Titrimetry. Objectives
Experiment 10 Acid-Base Titrimetry Objectives 1. To standardize an acid, HCl, solution. 2. To determine the concentration of an unknown Na 2 CO 3, sodium carbonate solution. Introduction Alkaline conditions
More informationDETERMINATION OF THE SOLUBILITY PRODUCT OF GROUPII HYDROXIDES
INTRODUCTION DETERMINATION OF THE SOLUBILITY PRODUCT OF GROUPII HYDROXIDES SOLUBILTY EQUILIBRIA Many systems in chemistry appear to be static when in fact they are in (dynamic) equilibrium. When a system
More informationCHEM 132 Lab 11 Western Carolina University
Name Lab Section Chemistry 132 Lab 11 How Effective is Your Antacid? Prelaboratory Exercise 1. How many grams of NaOH will you need to make 250 of 0.5 M NaOH solution? 2. What is the purpose of the first,
More informationTitration of Vinegar
EXPERIMENT 8 Prepared by Edward L. Brown, Lee University and Verrill M. Norwood, Cleveland State Community Collee The student will become familiar with the techniques of titration and expressin a solution
More informationCHEM 30A EXPERIMENT 8 & 9: ACID- BASE TITRATION. Learning Outcomes. Introduction. Upon completion of this lab, the student will be able to:
1 Learning Outcomes CHEM 30A EXPERIMENT 8 & 9: ACID- BASE TITRATION Upon completion of this lab, the student will be able to: 1) Prepare a solution of primary standard 2) Determine the molar concentration
More informationCHEM Practice to be done before the lab. Experiment 9 Introduction to Volumetric Techniques II. Objectives
1 CHEM 0011 Experiment 9 Introduction to Volumetric Techniques II Objectives 1. To learn the proper technique to use a burette. 2. To learn the proper technique to carry out a titration. 3. To verify the
More informationChemistry 151 Last Updated Dec Lab 10: The Neutralizing Ability of an Antacid (Titrations, Pt II)
Chemistry 151 Last Updated Dec. 2013 Lab 10: The Neutralizing Ability of an Antacid (Titrations, Pt II) Introduction The active ingredient of many antacids is a base that neutralizes excess stomach acid,
More informationEXPERIMENT A7: VINEGAR TITRATION. Learning Outcomes. Introduction. Upon completion of this lab, the student will be able to:
1 Learning Outcomes EXPERIMENT A7: VINEGAR TITRATION Upon completion of this lab, the student will be able to: 1) Prepare a solution of primary standard 2) Determine the molar concentration of a solution
More information8 Titration of Acids and bases
8 Titration of Acids and bases Name: Date: Section: Objectives Reinforce acid-base chemistry principles from chapter 4 in Silberberg Standardize a sodium hydroxide solution Determine the molarity of an
More informationDetermination of the K a Value and Molar Mass of an Unknown Weak Acid
10 Determination of the K a Value and Molar Mass of an Unknown Weak Acid Introduction In this experiment you will titrate a monoprotic weak acid with a strong base, and measure the titration curve with
More informationPreLAD: b. KHP is a monoprotic acid, what are the number of moles of ionizable H + in the approximately 0.25 g of KHP?
LAD G.1 (pg! 1 of 6! ) What % of vinegar is really acetic acid? Name Per What part of the solution is really HC2H3O2 aka CH3COOH? What is the Ka of acetic acid? Introduction: The acid in vinegar is acetic
More informationExperimental Procedure. Lab 406
Experimental Procedure Lab 406 Overview This experiment is to be complete in cooperation with other chemists/chemist groups in the laboratory. In PART A, a standardized solution of hydrochloric acid is
More informationExperiment 10. Acid Base Titration
Experiment 10 Acid Base Titration Definitions: Titration A technique to accurately and precisely measure something, most often acids or bases Acids Most acids are molecules that behave as if they were
More informationExperiment: Titration
Experiment: Titration INTRODUCTION In this experiment you will be determining the volume of sodium hydroxide solution of known concentration required to neutralize a known mass of an unknown acid in solution.
More informationChemistry Calibration of a Pipet and Acid Titration
Chemistry 3200 Today you are given a chance to brush up on some of the techniques that you will be using during the remainder of the semester. Lab grades will be based on obtaining the correct answer in
More informationEXPERIMENT 12B: TITRATION OF AN UNKNOWN ACID INTRODUCTION
EXPERIMENT 12B: TITRATION OF AN UNKNOWN ACID INTRODUCTION In this experiment you will determine the molar mass of an unknown acid by titration with the sodium hydroxide you prepared and standardized in
More informationPOGIL LAB EXERCISE 15 HOW DO YOU STANDARDIZE AN ACID AND BASE?
POGIL LAB EXERCISE 15 HOW DO YOU STANDARDIZE AN ACID AND BASE? POGIL LAB 15 Page 1 of 10 Each member should assume his or her role at this time. The new manager takes charge of the POGIL folder and hands
More informationAcid / Base Titrations
Acid / Base Titrations v051413_7pm Objectives: Determine the concentration of a base solution using an acid standard. Optional: Precipitate an ionic salt for percent yield determination using the standardized
More informationExperiment #10: Analysis of Antacids
Experiment #10: Analysis of Antacids Purpose: In this experiment you will prepare one solution that is approximately 0.1 M NaOH. Then you will standardize this solution, which means that you will experimentally
More informationTITRATION OF AN ACID WITH A BASE
TITRATION OF AN ACID WITH A BASE 1 NOTE: You are required to view the podcast entitled Use of Burets for Titrations before coming to lab this week. To view the podcast, consisting of eight episodes, go
More informationPre-lab: Read sections 10.6 in the textbook. Complete the attached pre-lab by Thursday, May 22.
Lab 5: Titration of an unknown acid Objective: Determine the concentration of an unknown monoprotic acid by titration, the process that matches the number of moles of base with the number of moles of acid.
More informationH 3 O + (aq) + P 2- (aq)
PURPOSE: To standardize a solution of sodium hydroxide by titration with a primary standard, (KHC 8 H 4 O 4 ), potassium hydrogen phthalate (KHC 8 H 4 O 4 ) PRINCIPLES: Most shelf reagents, such as 0.10
More informationAcid-Base Titration Lab
Acid-Base Titration Lab Name Objectives: - To apply knowledge of molarity to properly dilute a concentrated base - To apply knowledge of solution stoichiometry in order to correctly determine the unknown
More informationNaOH (aq) + HCl (aq) NaCl (aq) + H 2 O (l)
EXPERIMENT 21 Molarity of a Hydrochloric Acid Solution by Titration INTRODUCTION Volumetric analysis is a general term meaning any method in which a volume measurement is the critical operation; however,
More informationChem 2115 Experiment #7. Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution, analysis of vinegar & antacid tablets
Chem 2115 Experiment #7 Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution, analysis of vinegar & antacid tablets OBJECTIVE: The goals of this experiment are to learn titration
More informationPre-lab: Read section 9.9 (pages ) on acid-base titrations in the textbook. Complete the attached pre-lab by Tuesday, June 2.
Chemistry 121 Lab 5: Titration of an unknown acid Objective: Determine the concentration of an unknown monoprotic acid by titration, the process that matches the number of moles of base with the number
More informationDETERMINATION OF ACETIC ACID IN VINEGAR
DETERMINATION OF ACETIC ACID IN VINEGAR 1 INTRODUCTION Juices from plants and fruits contain sugar. When these juices are fermented, the sugar molecules are converted into ethyl alcohol molecules (C 2
More informationSupernatant: The liquid layer lying above the solid layer after a precipitation reaction occurs.
Limiting Reagent Introduction The quantities of substances involved in a chemical reaction represented by a balanced equation are often referred to as stoichiometric amounts. Solution stoichiometry is
More informationChapter 9. Volumetric Analysis
Chapter 9 Volumetric Analysis The terms volumetric analysis, titrimetry and titration are used interchangeably to describe a procedure which analyses chemicals in solution by accurate volume measurement.
More informationGETTING THE END POINT TO APPROXIMATE. Two hours
Chem 1312 Handout Experiment ONE Laboratory Time Required Special Equipment and Supplies Objective Safety First Aid GETTING THE END POINT TO APPROXIMATE THE EQUIVALENCE POINT Two hours Balance Potassium
More information2002 D Required 2001 D Required
2002 D Required A student is asked to determine the molar enthalpy of neutralization, H neut, for the reaction represented above. The student combines equal volumes of 1.0 M HCl and 1.0 M NaOH in an open
More informationAscorbic Acid Titration of Vitamin C Tablets
Ascorbic Acid Titration of Vitamin C Tablets Introduction This experiment illustrates how titration, the process of slowly adding one solution to another until the reaction between the two is complete,
More informationAscorbic Acid Titration of Vitamin C Tablets
Ascorbic Acid Titration of Vitamin C Tablets Introduction This experiment illustrates how titration, the process of slowly adding one solution to another until the reaction between the two is complete,
More informationAcidity of Beverages Lab
Acidity of Beverages Lab Name: Introduction: Common beverages may be either acidic or basic. Fruit juices, for example, get their sweet taste from sugars and their sour or tart taste from weak acids such
More informationChem 2115 Experiment #7. Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution and the analysis of antacid tablets
Chem 2115 Experiment #7 Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution and the analysis of antacid tablets OBJECTIVE: The goals of this experiment are to learn titration
More informationEXPERIMENT 22 SOLUBILITY OF A SLIGHTLY SOLUBLE ELECTROLYTE
EXPERIMENT 22 SOLUBILITY OF A SLIGHTLY SOLUBLE ELECTROLYTE INTRODUCTION Electrolytes are compounds that are present in solution as ions. They are more likely to be soluble in water than in most other liquids
More information*You should work in groups of no more than 3 students. Each individual is responsible for all data and information in their own booklet.
Name Period 1 *You should work in groups of no more than 3 students. Each individual is responsible for all data and information in their own booklet. Pre-Lab Questions: What is the molarity equation?
More information[Ca 2+ ] = s (3) [IO - 3 ] = 2s (4)
E10 Chemical Equilibria: K sp of Calcium Iodate Objective! Understand the relation between the molar solubility and the solubility product constant of a sparingly soluble salt.! Measure the molar solubility
More informationEXPERIMENT #9 PRELAB EXERCISES. Redox Titration (Molarity Version) Name Section. 1. Balance the following redox reaction under acidic conditions.
EXPERIMENT #9 PRELAB EXERCISES Redox Titration (Molarity Version) Name Section 1. Balance the following redox reaction under acidic conditions. C 2 O 2-4 (aq) + MnO - 4 (aq) CO 2 (g) + Mn 2+ (aq) 2. A
More informationEXPERIMENT 5 ACID-BASE TITRATION
EXPERIMENT 5 ACID-BASE TITRATION INTRODUCTION Much of chemistry and biology is concerned with the behavior of acids and bases. Acids and bases are participants in many reactions in nature, and many reactions
More informationAscorbic Acid Titration of Vitamin C Tablets
Ascorbic Acid Titration of Vitamin C Tablets Introduction This experiment illustrates how titration, the process of slowly adding one solution to another until the reaction between the two is complete,
More informationExperiment 4, Calculation of Molarity of H 3 PO 4 by Titration with NaOH Chemistry 201, Wright College, Department of Physical Science and Engineering
Name Date Experiment 4, Calculation of Molarity of H 3 PO 4 by Titration with NaOH Chemistry 201, Wright College, Department of Physical Science and Engineering Molarity is a common unit within the chemical
More information# 12 ph-titration of Strong Acids with Strong Bases
# 12 ph-titration of Strong Acids with Strong Bases Purpose: A strong acid solution is titrated with a strong base solution. A titration curve is then used to determine the endpoint and find the concentration
More informationExperiment 20-Acid-Base Titration: Standardization of KOH and Determination of the Molarity and/or Percent Composition of an Acid Solution
Experiment 20-Acid-Base Titration: Standardization of KOH and Determination of the Molarity and/or Percent Composition of an Acid Solution In this experiment, you will determine the molarity and percent
More informationSupernatant: The liquid layer lying above the solid layer after a precipitation reaction occurs.
Limiting Reagent Introduction The quantities of substances involved in a chemical reaction represented by a balanced equation are often referred to as stoichiometric amounts. Solution stoichiometry is
More informationChemistry 101 Experiment 12B-ANALYSIS OF COMMERCIAL VINEGARS
Vinegar is a solution of acetic acid (HC2H3O2). The strength or concentration of the vinegar is usually given on the label of the bottle in percent by weight or percent acidity. The United States Food
More informationLowell High School AP Chemistry Spring 2009 REACTION KINETICS EXPERIMENT
Lowell High School AP Chemistry Spring 2009 REACTION KINETICS EXPERIMENT Complete the following for Pre-Lab on a clean sheet of paper: (1) In your own words, explain the following: a. why the I 2 concentration
More informationName: Date: AP Chemistry. Titrations - Volumetric Analysis. Steps for Solving Titration Problems
Name: Date: AP Chemistry Titrations - Volumetric Analysis Term Volumetric analysis Burette Pipette titrate titre aliquot end point equivalence point indicator primary standard standardisation secondary
More informationTitration of an Unknown Acid
Experiment 6 Titration of an Unknown Acid Prepared by Stephen E. Schullery and Ross Nord, Eastern Michigan University PURPSE To determine the apparent molar mass of an unknown monoprotic acid by titrating
More informationTitration 2: CH 3 COOH Titrated with NaOH
Titration 2: CH 3 COOH Titrated with NaOH Titration 1: Acid is CH 3 COOH, phenolphthalein as the indicator 1. Obtain about 60 ml of the standardized ( 0.1 M) NaOH solution. CAUTION: Sodium hydroxide solution
More informationLAB 8: DETERMINATION OF ACETIC ACID CONTENT IN VINEGAR
LAB 8: DETERMINATIN F AETI AID NTENT IN VINEGAR Lab format: This lab is designed for delivery using the Remote Web-based Science Laboratory (RWSL) or a lab kit. INTRDUTIN In an acid-base titration, the
More informationPURPOSE: 1. To illustrate an oxidation-reduction titration with potassium permanganate 2. To determine the percent mass of iron in an unknown.
PURPOSE: 1. To illustrate an oxidation-reduction titration with potassium permanganate 2. To determine the percent mass of iron in an unknown. PRINCIPLES: Oxidation and reduction reactions, commonly called
More informationIf you have a Mac do whatever you have to do to play it as a slide show I don t know Macs well. Dr. Buckley
For best results please view this as a slide show. You can hit the F5 key or go to the Slide Show tab on the menu bar and click on From Beginning. Page Down and Page Up will move you through the presentation.
More informationExperiment 5 Titration of Acids and Bases
CEAC 103 GENERAL CHEMISTRY Experiment 5 Titration of Acids and Bases Purpose: To become familiar with the techniques of titration, a volumetric method of analysis; to determine the molarity and ph of an
More informationPercentage of Acetic Acid in Vinegar
Microscale Percentage of Acetic Acid in Vinegar When sweet apple cider is fermented in the absence of oxygen, the product is an acid, vinegar. Most commercial vinegars are made by fermentation, but some,
More informationSolubility of KHT and Common ion Effect
Solubility of KHT and Common ion Effect v010516 You are encouraged to carefully read the following sections in Tro (3 rd ed.) to prepare for this experiment: Sec 16.5, pp 783-788 (Solubility Equilibria
More informationAscorbic Acid Titration of Vitamin C Tablets
Ascorbic Acid Titration of Vitamin C Tablets Part A. Preparation of Vitamin C Tablet Solutions 1. Obtain two vitamin C tablets. Place a plastic weighing boat on the balance, and press zero to tare the
More informationSafety Note: Safety glasses and laboratory coats are required when performing this experiment
The Determination of Hypochlorite in Bleach Reading assignment: Burdge, Chemistry 4 th edition, section 4.6. We will study an example of a redox titration in order to determine the concentration of sodium
More informationTitration of Acetic Acid in Vinegar Minneapolis Community and Technical College v.9.17
Titration of Acetic Acid in Vinegar Minneapolis Community and Technical College v.9.17 Objective: To practice the correct use of the burette, volumetric pipette, and volumetric flask in analytical titrations.
More informationChemistry with Mr. Faucher. Acid-Base Titration
Chemistry with Mr. Faucher Name Date Acid-Base Titration 24 A titration is a process used to determine the volume of a solution needed to react with a given amount of another substance. In this experiment,
More informationFor this lab, you will determine the purity of the aspirin by titration and by spectrophotometric analysis.
Introduction: ommercially prepared aspirin tablets are not considered 100% pure acetylsalicylic acid. Most aspirin tablets contain a small amount of binder which helps prevent the tablets from crumbling.
More informationAscorbic Acid Titration of Vitamin C Tablets This lab will be completed individually! Make sure you come prepared!
Ascorbic Acid Titration of Vitamin C Tablets This lab will be completed individually! Make sure you come prepared! This laboratory experiment has a formal report. Consult the guidelines for writing a formal
More informationO H 3 O 1 1 A. O 1 1 OH (K w
CHAPTER 8 Acid Base Titration Curves Objectives The objectives of this experiment are to: Understand the titration curves for the following solutions: a strong acid: hydrochloric acid, HCl. a weak acid:
More informationSynthesis and Analysis of a Coordination Compound
Synthesis and Analysis of a Coordination Compound In addition to forming salts with anions, transition metal cations can also associate with neutral molecules (and ions) through a process called ligation.
More informationUnit 5 Part 2 Acids, Bases and Salts Titrations, Indicators and the ph Scale UNIT 5 ACIDS, BASES AND SALTS
UNIT 5 ACIDS, BASES AND SALTS PART 2 TITRATIONS, INDICATORS AND THE PH SCALE Contents 1. The ph scale 2. Indicators 3. Acid-Base Titrations Key words: acidic, alkaline, neutral, ph, indicator, litmus,
More informationExperiment 5E BOTTLES WITHOUT LABELS: STUDIES OF CHEMICAL REACTIONS
Experiment 5E BOTTLES WITHOUT LABELS: STUDIES OF CHEMICAL REACTIONS FV 1-21-16 MATERIALS: Eight 50 ml beakers, distilled water bottle, two 250 ml beakers, conductivity meter, ph paper (A/B/N), stirring
More informationExperiment 7: Titration of an Antacid
1 Experiment 7: Titration of an Antacid Objective: In this experiment, you will standardize a solution of base using the analytical technique known as titration. Using this standardized solution, you will
More informationPartner: Alisa 1 March Preparation and Properties of Buffer Solutions
Partner: Alisa 1 March 2012 Preparation and Properties of Buffer Solutions Purpose: The purpose of this experiment is to compare the ph effect on buffered and non-buffered solutions as well as making a
More informationWhen dealing with solids that one can weigh on a balance, determining the number of moles in a particular sample is simply:
Experiment 2 Stoichiometry Solids and Solutions Determining the Molarity of a Solution Lab Owl Announcement: Upon completion of this lab, log onto OWL. A Lab Owl section should now appear in your courses
More informationPartner: Judy 29 March Analysis of a Commercial Bleach
Partner: Judy 29 March 2012 Analysis of a Commercial Bleach Purpose: The purpose of this lab is to determine the amount of sodium hypochlorite (NaClO) in commercial bleach. This can be done by forming
More informationTitration of citric acid in juice
Page 4 LABORATORY LEARNING ACTIVITY Titration of citric acid in juice Introduction One common task that chemists must perform is to determine the concentration of a chemical using titration. There are
More informationExperiment 2: Reaction Stoichiometry by Thermometric Titration
Experiment 2: Reaction Stoichiometry by Thermometric Titration Introduction The net result of a reaction (a chemical change) is summarized by a chemical equation. In order to write a chemical equation,
More informationDetermining the Rate Law for a Chemical Reaction
Determining the Rate Law for a Chemical Reaction Purpose: To determine the reaction orders, rate law, and rate constant for the reaction between persulfate ions, SO8 -, and iodide ions, I - Introduction
More informationVolumetric Analysis: Analysis of antacid tablets Analysis of Cl - concentrations in IV solutions
Volumetric Analysis: Analysis of antacid tablets Analysis of Cl - concentrations in IV solutions OBJECTIVE: The goals of this experiment are to learn titration concepts and techniques. SKILLS: Titration,
More informationEXPERIMENT. Titration for Acetic Acid in Vinegar
EXPERIMENT Titration for Acetic Acid in Vinegar Hands-On Labs, Inc. Version 42-0208-00-02 Review the safety materials and wear goggles when working with chemicals. Read the entire exercise before you begin.
More informationPURPOSE: To determine the Rate Law for the following chemical reaction:
PURPOSE: To determine the Rate Law for the following chemical reaction: H 2 O 2 (aq) + 2 I - (aq) + 2 H 3 O + (aq) 4 H 2 O(l) + I 2 (aq) Hydrogen Iodide Hydronium Water Iodine Peroxide Ion Ion PRINCIPLES:
More information