MODELING AND OPTIMIZATION FOR DRILLING OF HIGH ASPECT RATIO BLIND MICRO HOLES IN MICRO EDM
|
|
- Douglas Richard
- 5 years ago
- Views:
Transcription
1 MODELING AND OPTIMIZATION FOR DRILLING OF HIGH ASPECT RATIO BLIND MICRO HOLES IN MICRO EDM Swapan Barman 1*, Kousv Mondol 2, Nagahanumaiah 3, Asit Baran Puri 4 1* CSIR-Central Mechanical Engineering Research Institute, Durgapur sbarman@cmeri.res.in 2 Kanksa Academy of Technology and Management, Panagarh kousvmondol@gmail.com 3 CSIR-Central Mechanical Engineering Research Institute, Durgapur , naga@cmeri.res.in 4 National Institute of Technology (NIT), Durgapur , India abpuri2000@yahoo.co.in Abstract In this communication, an attempt was taken study the influence of machining parameters like gap voltage, capacitance and depth of hole on machining performances for 2D and 3D surface finish of blind micro holes and electrode wear length in micro electrical discharge drilling (MEDD) process. The experimentation was carried out employing full facrial design (3 3 ) with three levels of each machining parameter study simultaneous effect of facrs on machining performance. Mathematical models have been developed for the mentioned machining outputs by multiple linear regression analysis. Response surface methodology was utilized carry out multiple response optimization and find the optimum process parameter settings for a desired yield by conur overlapping method using statistical software MINITAB 16 with 95% confidence level and with levels of facrs in coded units. The models so developed are excellent for acceptance as the coefficients of multiple determinations (R 2 ) for the above responses were computed as 97.18%, 97.79% and98.90% respectively. From the models, it was revealed that capacitance, gap voltage and depth of hole influence R a, S a and electrode wear length very strongly. Surface plots and conur plots were generated find out the relationship between the machining parameters and the output. The optimum parametric settings for the machining parameters were computed from overlaid conur plots. The proposed models could be considered as valuable ols for the process planning of MEDD leading cost effective machining of blind micro holes in industry. Keywords : MEDD, surface texture R a and S a, full facrial design, optimization. 1 Introduction In micro EDM, material removal takes place through melting and evaporation by discharge pulses when the thermoelectric energy is created between a ol electrode and a work piece usually submerged in a dielectric fluid and a spark gap is maintained between them. Advancement in development of CNC systems and spark generars, helps micro EDM process be focused on production of complicated and high aspect ratio micro features with improved machined surface quality with very small forces and good repeatability of the process reported by D.T. Pham et al. (2004). I. Puertas et al. (2004) discussed in their paper that EDM is a wide spread technique used in industry for high precision machining of all type of conductive materials such as metals, metallic alloys, graphite and some ceramic materials regardless of their hardness. Due this advantage, micro EDM has become one of the most reliable methods used extensively in micro mold making, production of dies, cavities and many complex 3D structures communicated by I. Alting et al. (2003). In MEDD,the ol (electrode) rotates provide better uniformity in the generated hole profile. Micro holes are the most basic machined features of micro manufacturing secrs used for various applications like circuit board of integrated circuit packages, fuel injection nozzles, spinneret holes, bio-medical filters and others found in article of T. Masuzawa (2000). Manufacturing of micro holes depends on several process variables. Many research works were conducted analyze the process variables find out optimal conditions for micro features manufactured. To study the effect for process parameters on surface finish of 809-1
2 MODELING AND OPTIMIZATION FOR DRILLING OF HIGH ASPECT RATIO BLIND MICRO HOLES IN MICRO EDM blind micro holes is very difficult in non-destructive method due miniature size of the holes irrespective of using high precision equipment and techniques. In this paper, an attempt was taken study the influence of machining parameters like gap voltage, capacitance and depth of hole on machining performances for 2D and 3D surface finish and electrode wear length in MEDD process on a Monel K-500 alloy plate using pure tungsten electrode. The experimentation was carried out employing full facrial design (3 3 ) with three levels of each machining parameters. A full facrial design allows study of simultaneous effects of several facrs on a process explained by D.C. Montgomery (2000) in his book. Mathematical models have been developed for the machining outputs by multiple linear regression analysis. Response surface methodology was utilized carry out multiple response optimization and find the optimum process parameter settings for a desired yield by conur overlapping method. Table 1 Machining parameters with their levels and coding identification Machining parameters Unit Varia Depth of hole, X1 mm ble Capacitance, X2 nf (f) Gap voltage, X3 V Fixed Spindle speed rpm Spark feed rate µm/s Threshold % Retrieval feed mm/ min Polarity Dir Coolant flow rate Levels m m 3000 s 4 60% 10 rect (workpiece +) constant 2 Experimentationand observation The objective of this study was investigate the influence of machining parameters like depth of hole (X1), Capacitance (X2) and gap voltage (X3) on 2D and 3D surface texture (R a and S a ) of blind holes and ol wear length (L). For this study, 27 micro holes were drilled on 6 mm thick Monel K-500 alloy plate with tungsten electrode of diameter 300 µm by a high precision, integrated multi-process machine ol for micro machining (model DT-110 of M/s. MikroolsPte Ltd, Singapore) with combinationn of machining parameters shown in Table 1.Properties of workpiece, electrode and dielectric fluid were presented in Table 2. Blind micro holes were opened axially by wire EDM (WEDM) (model :Elektra Supercut 634, make : Electronica Machine Tools, Pune). Taylor-Hobson, UK make high accuracy 3D optical surface profiler (model : CCI Lite, resolution : 0.1Å) was used scan the opened holes and measure R a and S a surface texture characteristics of opened holes. Marcel-Aubert, SA make optical microscope (model : MA-705-Z1) and Olympus, Japan make image analyzer (model : BX51M, camera : Olympus-E330) were used take theimages of the holes. The phograph of MEDD, images of p of the micro hole, opened micro holes and ol electrode were shown in Figure 1. Statistical software MINITAB 16 (trial version) was used for regression analysis and analysis of variance (ANOVA) assuming that a second order polynomial model could sufficiently represent the above input output relationship. The mathematical models have been developed for R a, S a and electrode wear length by multiple linear regression analysis with 95% confidence level with facr levels in coded units. (a) (b) (c) (d) Figure 1 Images of (a) MEDD, (b) p of blind hole, (c) ol electrode and (d) opened micro holes. Table 2 Properties of workpiece, ol electrode material and dielectric fluid Workpiece (MONEL K-500 alloy) Density Hardness Melting point Thermal conductivity Thermal expansion coefficient Tool electrode (Tungsten) Density Hardness Melting point Relative conductivity ( silver) Thermal expansion coefficient Dielectric fluid (EDM oil 3) Volumetric mass at 15ºC Viscosity at 20 ºC Flash point (Pensky-Martens) Au ignition temperature 8.44 g/cc HRC35 (max.) ºC 17.5 W/m K 13.7x10-6 K g/cc HRA ºC x10-6 K Kg/m mm 2 /s 134 ºC 470 ºF 809-2
3 Values of gap voltage and depth of hole shown in Table 1 were coded as follows: Coded value, = ( ) ( ) (1) Log scale was used code the values of capacitance as follows : Coded value, = ( ) (2) ( ) The extracted profile of scanned surface of the opened micro hole for R a measurement, scanned surface and 3D surface of the opened holes number 7 and 8 were presented in Figure 2(a), 2(b) and 2(c) respectively. The observed values of electrode wear length calculated by taking length of electrode before and after machining and R a and S a values measured by 3D optical surface profilerwere given in Table 3. (b) (a) Figure 2 Imagesfrom 3D profiler : (a) Profile for R a measurement, (b) scanned surface data of opened hole 7 & hole 8 and (c) 3D images of hole7 & hole 8. 3 Results and Discussion As assumed that a second order polynomial model could sufficiently represent the selected input output relationship for the present study, so the regression analysis and ANOVA were performed considering following second order model of generalized form : (c) = β +β +β +β, (3) Table 3 Measured values of R a, S a and L Exp. No. R a (µm) S a (µm) L(mm) where, Y is the response (predicted), β 0 is the intercept, β i is the coefficient corresponding the facr X i, β ii is the coefficient of X i 2 and β ij is the coefficient of X i X j, for i, j = 1, 2,.., n, and i < j. For 3 responses X 1, X 2 and X 3, the above equation can be simplified as =β +β +β +β +β +β + β +β +β +β (4) Table 4 Coefficients of Regression Models Terms Coeff. of R a Coeff. of S a Coeff. of L Const X X X
4 MODELING AND OPTIMIZATION FOR DRILLING OF HIGH ASPECT RATIO BLIND MICRO HOLES IN MICRO EDM X1*X X2*X X3*X X1*X X1*X X2*X So, by multiple linear regression analysis, mathematical models were developed for R a, S a and electrode wear length (L). The coefficients and summary of ANOVA were represented concisely in Table 4 and Table 5 respectively. Table 5 Summary of ANOVA for responses Source P values For R a For S a For L Regression Linear X X X Square X1*X X2*X X3*X Interaction X1*X X1*X X2*X L 98.90% 96.67% 98.32% From the above results, the mathematical models for 2D surface finish R a (Y1), 3D surface finish S a (Y2) and electrode wear length L (Y3) were obtained as follows : Y1 = *X *X *X *X *X *X *X1*X *X1*X *X2*X3 (5) Y2= *X *X *X *X *X *X *X1*X *X1*X *X2*X3 (6) Y3= *X *X *X *X *X *X *X1*X *X1*X *X2*X3 (7) The response surface plots for all responses were plotted against selected variable machining parameters and presented in Figure 3. Term with P-value for regression less than 0.05 is considered as significant in the fitted models. From the models, it was revealed that capacitance, gap voltage and depth of hole influence R a, S a and L very strongly.the models so developed are excellent for acceptance as the coefficients of multiple determinations, R 2 for the above responses were computed as 97.18%, 97.79% and98.90% respectively. R 2 is a measure of the amount of reduction in the variability of Y obtained by using the model. Focus on the model is maximize the adjusted R 2 and the predicted R 2 for acceptance as discussed by R. H. Myers et al. in their book (2009). From model summary statistics shown in Table6, it could be revealed that the models developed are excellent for acceptance as R 2, adjusted R 2 and predicted R 2 for the above responses were computed are very closer unity,as desired for a model, giving better its predictions for responses. Table 6 R-squared values for responses R-squared Values R 2 Predicted R 2 Adjusted R 2 R a 97.18% 93.14% 95.69% S a 97.79% 94.28% 96.62% 809-4
5 Variables X1 : Depth of micro hole X2 : Capacitance X3 : Gap voltage Y1 : 2D surface finish, R a Y2 : 3D surface finish, S a Y3 : Electrode wear length Figure 3Response surface plots of R a, S a and L against machining parameters. From surface plots the minimum values of responses R a, S a and L were computed for gap voltage of 90V, capacitance of 1nF and depth of hole for 2 mm.all the responses keep increasing with increase in gap voltage, capacitance and depth of hole. Variables X1 : Depth of micro hole X2 : Capacitance X3 : Gap voltage R a : 2D surface finish, S a : 3D surface finish, L : Electrode wear length Figure 4 Conur plots of responses against machining parameters Conur plots shown in Figure 4 were generated find out the relationship between the machining parameters and the responses. The optimum parametric settings for the machining parameters were computed from overlaid conur plots. In Figure 5(a) 5(f) overlaid zones of machining parameters for selected range of responses were plotted. For finding out the overlaid zone of machining parameters, selected values chosen for R a, S a and L were from 6.2 µm 6.6 µm, from 17 µm 17.5 µm and from 0.15 mm 0.18 mm respectively. Optimum parametric settings between R a and S a were not considered as both are represent surface texture of the machined surfaces in 2D and 3D form respectively. Optimized zoneof machining parameters gap voltage, capacitance and depth of hole for selected range of R a, S a and L were tabulated in Table
6 MODELING AND OPTIMIZATION FOR DRILLING OF HIGH ASPECT RATIO BLIND MICRO HOLES IN MICRO EDM parameters on R a, S a and electrode wear length L by full facrial design. Mathematical models were developed for outputs by multiple linear regression analysis. The optimum process parameter settings for a desired yield were computed by conur overlapping methodof response surface methodology. It was observed that i)all considered machining parameters gap voltage, capacitance and depth of micro hole were very strongly significant for selected responses S a, R s and L. ii) The mathematical models developed were excellent for acceptance as coefficients of multiple determinations, R 2, adjusted R 2 and predicted R 2 for the selected responses computed were very closer unity. The proposed models could be considered as valuable ols for the process planning of MEDD of blind micro holes in industry. Variables X1:Depth of hole X2:Capacitance X3:Gap voltage R a : 2D surface finish, S a : 3D surface finish, L : Electrode wear length Figure 5Overlaid zone of machining parameters for selected range of responses : (a) (c) for R a and L & (d) (e) for S a and L Table 7 Optimizedzoneof Gap Voltage, Capacitance and Depth of hole for selected range of R a, S a and electrode wear length L Selected range of responses R a (µm) L (mm) S a (µm) L (mm) Conclusions Gap Voltage(V) Optimized zone Capacitance (nf) Depth of hole (mm) Twenty seven blind micro holes of different hole depth were drilled on Monel K-500 by tungsten electrode of 300 µm diameter with combinations of varying machining parameters gap voltage, capacitance and depth of hole study the influence of machining iii) Conur plots for R a, S a and L were plotted against machining parameters gap voltage, capacitance and depth of blind micro holes. The optimum parametric settings for the machining parameters were computed from overlaid conur plots of responses. iv) For machining a surface of R a of 6.2 µm 6.6 µm, S a of 17 µm 17.5 µm for MonelK-500 alloy and with electrode wear length of 150 µm 180 µm for tungsten electrode of 300 µm diameter, the optimized zoneof machining parameters gap voltage, capacitance and depth of hole were computed. Acknowledgement Authors are thankful Department of Science and Technology, Govt. of India (SERB Grant no. SR/S3/MERC/0020/2012 dated ) for financial support the project on micro EDM and also thankful Direcr, CSIR-Central Mechanical Engineering Research Institute, Durgapur for kind permission submit the paper AIMTDR References Alting, I., Kimourta, F., Hansen, H.N. and Bissacco, G. (2003), Micro engineering, Annals CIRP Manufacturing Technology, Vol. 52(2), pp Masuzawa, T. (2000), State of art of micromachining, Annals CIRP Manufacturing Technology, Vol. 49(2), pp Montgomery, D.C.(2000), Design and analysis of experiments, John Wiley & Sons, 5th Edition Myers R.H., Montgomery, D.C. and Anderson-Cook, C.M. (2009), Response surface methodology : Process and product optimization using designed experiments, 809-6
7 John Wiley & Sons, 3 rd Edition Pham, D.T., Dimov, S.S., Bigot, A. and Popov K.(2004),Micro-EDM recent developments and research issues, Journal of Material Processing Technology, Vol.149, pp Puertas, I., Luis, C.J. and Alvarez, I. (2004), Analysis of the influence of EDM parameter on surface quality, MRR and EW of WC-Co, Journal of Material Processing Technology, Vol. 153/154 pp
Study of the effect of machining parameters on material removal rate and electrode wear during Electric Discharge Machining of mild steel
Journal of Engineering Science and Technology Review 5 (1) (2012) 14-18 Research Article JOURNAL OF Engineering Science and Technology Review www.jestr.org Study of the effect of machining parameters on
More informationAssociate Professor, Department of Mechanical Engineering, Birla Institute of Technology, Mesra, Ranchi, India
Optimization of machine process parameters on material removal rate in EDM for EN19 material using RSM Shashikant 1, Apurba Kumar Roy 2, Kaushik Kumar 2 1 Research Scholar, Department of Mechanical Engineering,
More informationA STUDY OF THE ACCURACY OF THE MICRO ELECTRICAL DISCHARGE MACHINING DRILLING PROCESS
A STUDY OF TE ACCURACY OF TE MICRO ELECTRICAL DISCARGE MACINING DRILLING PROCESS D.T. Pham, S.S. Dimov, S. Bigot, A. Ivanov, and K. Popov Manufacturing Engineering Centre, School of Engineering, Cardiff
More informationExperimental Investigation of Micro-EDM Process on Brass using Taguchi Technique
Experimental Investigation of Micro-EDM Process on Brass using Taguchi Technique Ananya Upadhyay ananya.upadhyay@gmail.com Vijay Pandey Vinay Sharma Ved Prakash CSIR- Central Mechanical Engineering Research
More informationOptimization of EDM process parameters using Response Surface Methodology for AISI D3 Steel
Optimization of EDM process parameters using Response Surface Methodology for AISI D3 Steel Mr.B.Gangadhar 1, Mr.N. Mahesh Kumar 2 1 Department of Mechanical Engineering, Sri Venkateswara College of Engineering
More informationInvestigation of effect of process parameters in micro hole drilling
Investigation of effect of process parameters in micro hole drilling Vaibhav Gosavi, Dr. Nitin Phafat, Dr. Sudhir Deshmukh 3 Research scholar,me MFG, JNEC Asso. Prof. Mech. Dept., JNEC 3 Principal, JNEC
More informationOn machine measurements of electrode wear in micro EDM milling
Downloaded from orbit.dtu.dk on: Nov 13, 2018 On machine measurements of electrode wear in micro EDM milling Valentincic, J.; Bissacco, Giuliano; Tristo, G. Published in: ISMTII 2003 Publication date:
More informationRESPONSE SURFACE ANALYSIS OF EDMED SURFACES OF AISI D2 STEEL
Advanced Materials Research Vols. 264-265 (2011) pp 1960-1965 Online available since 2011/Jun/30 at www.scientific.net (2011) Trans Tech Publications, Switzerland doi:10.4028/www.scientific.net/amr.264-265.1960
More informationStudy of water assisted dry wire-cut electrical discharge machining
Indian Journal of Engineering & Materials Sciences Vol. 1, February 014, pp. 75-8 Study of water assisted dry wire-cut electrical discharge machining S Boopathi* & K Sivakumar Department of Mechanical
More informationDrilling Microholes in Hot Tool Steel by Using Micro-Electro Discharge Machining
Materials Transactions, Vol. 48, No. 2 (27) pp. 25 to 21 #27 The Japan Institute of Metals Drilling Microholes in Hot Tool Steel by Using Micro-Electro Discharge Machining T. Y. Tai 1, T. Masusawa 2 and
More informationInternational Journal of Scientific & Engineering Research, Volume 5, Issue 1, January ISSN
International Journal of Scientific & Engineering Research, Volume 5, Issue 1, January-2014 2026 Modelling of Process Parameters on D2 Steel using Wire Electrical Discharge Machining with combined approach
More informationA Parametric Optimization of Electric Discharge Drill Machine Using Taguchi Approach
A Parametric Optimization of Electric Discharge Drill Machine Using Taguchi Approach Samar Singh, Lecturer, Dept of Mechanical Engineering, R.P. Indraprastha Institute of Technology (Karnal) MukeshVerma,
More informationOptimization of Machining Parameters in Wire Cut EDM of Stainless Steel 304 Using Taguchi Techniques
Advanced Materials Manufacturing & Characterization Vol. 8 Issue 1 (018) Advanced Materials Manufacturing & Characterization journal home page: www.ijammc-griet.com Optimization of Machining Parameters
More informationELECTRIC DISCHARGE MACHINING AND MATHEMATICAL MODELING OF Al-ALLOY-20 % SiC p COMPOSITES USING COPPER ELECTRODE
International Journal of Mechanical and Production Engineering Research and Development (IJMPERD ) ISSN 2249-6890 Vol.2, Issue 2 June 2012 37-46 TJPRC Pvt. Ltd., ELECTRIC DISCHARGE MACHINING AND MATHEMATICAL
More informationExperimental study of electrical discharge drilling of stainless steel UNS S30400
IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Experimental study of electrical discharge drilling of stainless steel UNS S30400 To cite this article: E A H Hanash and M Y Ali
More informationModeling of Wire Electrical Discharge Machining of AISI D3 Steel using Response Surface Methodology
5 th International & 26 th All India Manufacturing Technology, Design and Research Conference (AIMTDR 214) December 12 th 14 th, 214, IIT Guwahati, Assam, India Modeling of Wire Electrical Discharge Machining
More informationModeling of Wire Electrical Discharge Machining Parameters Using Titanium Alloy (Ti-6AL-4V)
Modeling of Wire Electrical Discharge Machining Parameters Using Titanium Alloy (Ti-6AL-4V) Basil Kuriachen 1, Dr. Josephkunju Paul 2, Dr.Jose Mathew 3 1 Research Scholar, Department of Mechanical Engineering,
More informationMr. Harshit K. Dave 1, Dr. Keyur P. Desai 2, Dr. Harit K. Raval 3
Investigations on Prediction of MRR and Surface Roughness on Electro Discharge Machine Using Regression Analysis and Artificial Neural Network Programming Mr. Harshit K. Dave 1, Dr. Keyur P. Desai 2, Dr.
More informationModeling and Optimization of WEDM Process Parameters on Machining of AISI D2 steel using Response Surface Methodology (RSM)
Modeling and Optimization of WEDM Process Parameters on Machining of AISI D2 steel using Response Surface Methodology (RSM) Sk. Mohammed Khaja 1, Ratan Kumar 2 Vikram Singh 3 1,2 CIPET- Hajipur, skmdkhaja@gmail.com
More informationElectrode set-up for EDM-drilling of large aspect-ratio microholes
Available online at www.sciencedirect.com Procedia CIRP 6 (013 ) 74 79 The Seventeenth CIRP Conference on Electro Physical and Chemical Machining (ISEM) Electrode set-up for EDM-drilling of large aspect-ratio
More informationMICRO ELECTRO DISCHARGE MACHINING OF Γ -TITANIUM ALUMINIDE ALLOY
MICRO ELECTRO DISCHARGE MACHINING OF Γ -TITANIUM ALUMINIDE ALLOY S.Mitra 1, G. Paul 2, S.Sarkar 1, and Nagahanumaiah 3 1 Department of Production Engineering, Jadavpur University, Kolkata, India 2 Department
More informationAnalysisoMRRandSRwithDifferentElectrodeforSS316onDi-SinkingEDMusingTaguchiTechnique
Global Journal of Researches in Engineering Mechanical and Mechanics Engineering Volume 13 Issue 3 Version 1.0 Year 013 Type: Double Blind Peer Reviewed International Research Journal Publisher: Global
More informationCHAPTER 6 MACHINABILITY MODELS WITH THREE INDEPENDENT VARIABLES
CHAPTER 6 MACHINABILITY MODELS WITH THREE INDEPENDENT VARIABLES 6.1 Introduction It has been found from the literature review that not much research has taken place in the area of machining of carbon silicon
More informationParameter Optimization of EDM on En36 Alloy Steel For MRR and EWR Using Taguchi Method
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-184,p-ISSN: 2320-334X, Volume 13, Issue 3 Ver. VII (May- Jun. 201), PP 5-5 www.iosrjournals.org Parameter Optimization of EDM on
More informationMODELING OF SURFACE ROUGHNESS IN WIRE ELECTRICAL DISCHARGE MACHINING USING ARTIFICIAL NEURAL NETWORKS
Int. J. Mech. Eng. & Rob. Res. 013 P Vijaya Bhaskara Reddy et al., 013 Research Paper ISSN 78 0149 www.ijmerr.com Vol., No. 1, January 013 013 IJMERR. All Rights Reserved MODELING OF SURFACE ROUGHNESS
More informationAn investigation of material removal rate and kerf on WEDM through grey relational analysis
Journal of Mechanical Engineering and Sciences ISSN (Print): 2289-4659; e-issn: 2231-8380 Volume 12, Issue 2, pp. 3633-3644, June 2018 Universiti Malaysia Pahang, Malaysia DOI: https://doi.org/10.15282/jmes.12.2.2018.10.0322
More informationStudy on Erosion Mechanism of Magnetic-field-assisted Micro-EDM
Study on Erosion Mechanism of Magnetic-field-assisted Micro-EDM Xuyang Chu a, Kai Zhu b, Yiru Zhang c and Chunmei Wang d Department of mechanical and electrical engineering, Xiamen University, Xiamen 361005,
More informationEXPERIMENTAL INVESTIGATIONS ON ORBITAL ELECTRO DISCHARGE MACHINING OF INCONEL 718 USING TAGUCHI TECHNIQUE
International Journal of Modern Manufacturing Technologies ISSN 2067 3604, Vol. IV, No. 1 / 2012 53 EXPERIMENTAL INVESTIGATIONS ON ORBITAL ELECTRO DISCHARGE MACHINING OF INCONEL 718 USING TAGUCHI TECHNIQUE
More informationOptimization of Radial Force in Turning Process Using Taguchi s Approach
5 th International & 6 th All India Manufacturing Technology, Design and Research Conference (AIMTDR 04) December th 4 th, 04, IIT Optimization of Radial Force in Turning Process Using Taguchi s Approach
More informationImpact of Microchannel Geometrical Parameters in W-EDM Using RSM
International Journal of Bioinformatics and Biomedical Engineering Vol. 1, No. 2, 2015, pp. 137-142 http://www.aiscience.org/journal/ijbbe Impact of Microchannel Geometrical Parameters in W-EDM Using RSM
More informationThe Influence of EDM Parameters in Finishing Stage on Surface Quality, MRR and EWR
Research Journal of Applied Sciences, Engineering and Technology 4(10): 1287-1294, 2012 ISSN: 2040-7467 Maxwell Scientific Organization, 2012 Submitted: December 09, 2011 Accepted: December 26, 2011 Published:
More informationOptimization of Cutting Parameter of (SS302) on EDM using Taguchi Method Chintan A. Prajapati 1 Prof. Dr. Prashant Sharma 2 Prof.
IJSRD - International Journal for Scientific Research & Development Vol. 2, Issue 01, 14 ISSN (online): 2321-013 Optimization of tting Parameter of (SS302) on EDM using Taguchi Method Chintan A. Prajapati
More informationStatistical and regression analysis of Material Removal Rate for wire cut Electro Discharge Machining of SS 304L using design of experiments
Vol. 2(5), 200, 02028 Statistical and regression analysis of Material Removal Rate for wire cut Electro Discharge Machining of SS 304L using design of experiments Vishal Parashar a*, A.Rehman b, J.L.Bhagoria
More informationStatistical and Experimental Study on the Influence of Input Parameters on the Dimensional Accuracy of Workpiece in EDM
Proceedings of the 212 International Conference on Industrial Engineering and Operations Management Istanbul, Turkey, July 3 6, 212 Statistical and Experimental Study on the Influence of Input Parameters
More informationOptimization Of Process Parameters In Drilling Using Taguchi Method
Optimization Of Process Parameters In Drilling Using Taguchi Method 1 P.Surendra, 2 B.Krishna Murthy, 3 M.V.Kiran Kumar 1 Associate Professor, 2 Assistant Professor, 3 Assistant Professor Department of
More informationOPTIMIZATION OF MATERIAL REMOVAL RATE AND SURFACE ROUGHNESSIN WED-MACHINING OF TiNi SMA USING GREY RELATION ANALYSIS
OPTIMIZATION OF MATERIAL REMOVAL RATE AND SURFACE ROUGHNESSIN WED-MACHINING OF TiNi SMA USING GREY RELATION ANALYSIS Manjaiah M 1*, Narendranath S 2, Basavarajappa S 3 1* Dept. of Mechanical Engineering,
More informationAnalysis and Mathematical Modeling of Wire EDM Process Parameters for Commercial Graphite by Using Response Surface Methodology
Advance Research and Innovations in Mechanical, Material Science, Industrial Engineering and Management - ICARMMIEM-201 7 Analysis and Mathematical Modeling of Wire EDM Process Parameters for Commercial
More informationInfluence of Input Parameters on Characteristics of Electro Chemical Machining Process
International Journal of Applied Science and Engineering 23., : 3-24 Influence of Input Parameters on Characteristics of Electro Chemical Machining Process C. Senthilkumara,*, G. Ganesana, and R. Karthikeyanb
More informationMULTI-RESPONSE OPTIMIZATION OF EDM PERFORMANCE CHARACTERISTICS USING RESPONSE SURFACE METHODOLOGY AND DESIRABILITY FUNCTION
VOL. 9, NO. 1, DECEMBER 014 ISSN 1819-6608 006-014 Asian Research Publishing Network (ARPN). All rights reserved. MULTI-RESPONSE OPTIMIZATION OF EDM PERFORMANCE CHARACTERISTICS USING RESPONSE SURFACE METHODOLOGY
More informationOptimization of WEDM Parameters for Super Ni-718 using Neutrosophic Sets and TOPSIS Method
Optimization of WEDM Parameters for Super Ni-718 using Neutrosophic Sets and TOPSIS Method Y Rameswara Reddy 1*, B Chandra Mohan Reddy 2 1,2 Department of Mechanical Engineering, Jawaharlal Nehru Technological
More informationEffect and Optimization of EDM Process Parameters on Surface Roughness for En41 Steel
, pp. 33-358 http://dx.doi.org/10.157/ijhit.01.9.5.9 Effect and Optimization of EDM Process Parameters on Surface Roughness for En1 Steel Ch. Maheswara Rao 1 and K.Venkatasubbaiah 1 (Assistant Professor,
More informationModelling Of Micro Electric Discharge Machining Using FEM
5 th International & 26 th All India Manufacturing Technology, Design and Research Conference (AIMTDR 214) December 12 th 14 th, 214, IIT Guwahati, Assam, India Modelling Of Micro Electric Discharge Machining
More informationOptimization of MRR and SR by employing Taguchis and ANOVA method in EDM
Optimization of and SR by employing Taguchis and ANOVA method in EDM Amardeep Kumar 1, Avnish Kumar Panigrahi 2 1M.Tech, Research Scholar, Department of Mechanical Engineering, G D Rungta College of Engineering
More informationDrilling Mathematical Models Using the Response Surface Methodology
International Journal of Mechanical & Mechatronics Engineering IJMME-IJENS Vol:5 No:06 9 Drilling Mathematical Models Using the Response Surface Methodology Panagiotis Kyratsis, Nikolaos Taousanidis, Apostolos
More informationA Review Paper on Rotary Electro-Discharge Machining
A Review Paper on Rotary Electro-Discharge Machining 1 Mr. Ganesh Pandurang Jadhav, 2 Dr. Narendra Narve 1 P.G.Student, 2 Professor Department Of Mechanical Engineering, JSPM Bhagwant Institute of Technology,
More informationMATHEMATICAL MODELING OF MATERIAL REMOVAL RATE OF T90Mn2W50Cr45 TOOL STEEL IN WIRE ELECTRICAL DISCHARGE MACHINE
International Journal of Mechanical and Materials Engineering (IJMME), Vol. 7 (01), No. 3, 03-08. MATHEMATICAL MODELING OF MATERIAL REMOVAL RATE OF T90MnW50Cr45 TOOL STEEL IN WIRE ELECTRICAL DISCHARGE
More informationOptimization of Machining Process Parameters in Drilling of
Optimization of Machining Process Parameters in Drilling of CFRP Using Multi-Objective Taguchi Technique, TOPSIS and RSA Optimization of Machining Process Parameters in Drilling of CFRP Using Multi-Objective
More informationPuttur, Andhra Pradesh, India , Andhra Pradesh, India ,
th International & th All India Manufacturing Technology, Design and Research Conference (AIMTDR ) December th th,, IIT Guwahati, Assam, India OPTIMIZATI OF DIMENSIAL DEVIATI:WIRE CUT EDM OF VANADIS- E
More informationAS INGPEED Development Journal in Integrated Engineering (ISSN:requested) 2013, Vol. 1
Variation effect of parameters related to the closed-loop control of the EDM-machine on the hydraulic flow and microhole diameters of injection nozzles constructed with steel 18CrNi8 Author: Alexandre
More informationResearch Article Study of Tool Wear and Overcut in EDM Process with Rotary Tool and Magnetic Field
Advances in Tribology Volume 212, Article ID 895918, 8 pages doi:1.1155/212/895918 Research Article Study of Tool Wear and Overcut in EDM Process with Rotary Tool and Magnetic Field Reza Teimouri and Hamid
More informationNumerical Modeling and Multi-Objective Optimization of Micro-Wire EDM Process
5 th International & 26 th All India Manufacturing Technology, Design and Research Conference (AIMTDR 2014) December 12 th 14 th, 2014, IIT Guwahati, Assam, India Numerical Modeling and Multi-Objective
More informationPercentage of harmful discharges for surface current density monitoring in electrical discharge machining process
1677 Percentage of harmful discharges for surface current density monitoring in electrical discharge machining process O Blatnik*, J Valentincic, and M Junkar Faculty of Mechanical Engineering, University
More informationNeuro-fuzzy model and Regression model a comparison study of MRR in Electrical discharge machining of D2 tool steel
Neuro-fuzzy model and Regression model a comparison study of MRR in Electrical discharge machining of D2 tool steel M. K. Pradhan*, and C. K. Biswas, Abstract In the current research, neuro-fuzzy model
More informationModelling And Optimization Of Electro Discharge Machining In C45 Material
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X PP. 25-32 www.iosrjournals.org Modelling And Optimization Of Electro Discharge Machining In C45 Material
More informationPost Graduate Scholar, Department of Mechanical Engineering, Jalpaiguri Govt. Engineering College, India. 2
International Journal of Technical Research and Applications e-issn: 30-8163, www.ijtra.com Volume 3, Issue 3 (May-June 015), PP. 5-60 INFLUENCE OF CONTROL PARAMETERS ON IN ELECTRICAL DISCHARGE MACHINING
More informationOPTIMIZATION OF MACHINING PARAMETERS USING DESIRABILITY FUNCTION ANALYSIS AND ANOVA FOR THERMO-MECHANICAL FORM DRILLING
International Journal of Industrial Engineering & Technology (IJIET) ISSN(P): 2277-4769; ISSN(E): 2278-9456 Vol. 4, Issue 1, Feb 2014, 19-26 TJPRC Pvt. Ltd. OPTIMIZATION OF MACHINING PARAMETERS USING DESIRABILITY
More informationStudy of EDM Parameters on Mild Steel Using Brass Electrode
Study of EDM Parameters on Mild Steel Using Brass Electrode Amit Kumar #1, Abhishek Gaikwad *2, Amit Tiwari #3 # 1,3, Production Engineering (ME), SSET, Allahabad-211007, SHIATS, Allahabad, Uttar Pradesh
More informationTHere is a heavy demand of the advanced materials with
Vol:3, No:9, 29 Neuro-fuzzy model and Regression model a comparison study of MRR in Electrical discharge machining of D2 tool steel M. K. Pradhan*, and C. K. Biswas, International Science Index, Mechanical
More informationModeling and Simulation of Surface Roughness in Wire Electrical Discharge Turning Process
nd International Conference on Computer Engineering, Information Science & Application Technology (ICCIA 7) Modeling and Simulation of Surface Roughness in Wire Electrical Discharge Turning Process Xiaoteng
More informationEXPERIMENTAL INVESTIGATION OF MRR, SURFACE ROUGHNESS AND OVERCUT OF AISI 304 STAINLESS STEEL IN EDM A THESIS SUBMITTED IN PARTIAL FULFILMENT
EXPERIMENTAL INVESTIGATION OF MRR, SURFACE ROUGHNESS AND OVERCUT OF AISI 304 STAINLESS STEEL IN EDM A THESIS SUBMITTED IN PARTIAL FULFILMENT OF THE REQUIREMENTS FOR THE DEGREE OF Bachelor of Technology
More informationOptimization of parameters on material removal rate in micro-wedg process
MultiCraft International Journal of Engineering, Science and Technology Vol. 3, No. 9, 011, pp. 66-76 INTERNATIONAL JOURNAL OF ENGINEERING, SCIENCE AND TECHNOLOGY www.ijest-ng.com www.ajol.info/index.php/ijest
More information2. To compare results with a previous published work[6].
Predicting Material Removal Rate of EDM of 95WC/5NI Composites Fuzzy Logic Omar M Elmabrouk Industrial and Manufacturing Systems Engineering Department Benghazi University Benghazi, Libya omarelmabrouk@uobeduly
More informationModeling and Optimization of Milling Process by using RSM and ANN Methods
Modeling and Optimization of Milling Process by using RSM and ANN Methods M.R. SOLEYMANI YAZDI, A. KHORRAM Abstract Nowadays numerical and Artificial Neural Networks (ANN) methods are widely used for both
More informationOptimization of process parameter in electrochemical machining. Of Inconel 718 by Taguchi analysis
International Journal of Engineering Research and General Science Volume, Issue, January-February, 05 ISSN 09-70 Optimization of process parameter in electrochemical machining Of Inconel 78 by Taguchi
More informationApplication of Taguchi method in optimization of control parameters of grinding process for cycle time reduction Snehil A. Umredkar 1, Yash Parikh 2
Application of Taguchi method in optimization of control parameters of grinding process for cycle time reduction Snehil A. Umredkar, Yash Parikh 2 (Department of Mechanical Engineering, Symbiosis Institute
More informationMaterial removal characteristics of microslot (kerf) geometry
DOI 10.1007/s00170-010-2645-z ORIGINAL ARTICLE Material removal characteristics of microslot (kerf) geometry in μ-wedm on aluminum Kodalagara Puttanarasaiah Somashekhar & Nottath Ramachandran & Jose Mathew
More informationAll about sparks in EDM
All about sparks in EDM (and links with the CLIC DC spark test) Antoine Descoeudres, Christoph Hollenstein, Georg Wälder, René Demellayer and Roberto Perez Centre de Recherches en Physique des Plasmas
More informationPerformance analysis of µed-milling process using various statistical techniques
Int. J. Machining and Machinability of Materials, Vol. 11, No. 2, 2012 183 Performance analysis of µed-milling process using various statistical techniques G. Karthikeyan Department of Mechanical Engineering,
More informationTaguchi-grey relational based multi response optimization of electrical process parameters in electrical discharge machining
Indian Journal of Engineering & Materials Science Vol. 20, December 2013, pp. 471-475 Taguchi-grey relational based multi response optimization of electrical process parameters in electrical discharge
More informationOptimization of Process Parameters in CNC Drilling of EN 36
Optimization of Process Parameters in CNC ing of EN 36 Dr. K. Venkata Subbaiah 1, * Fiaz khan 2, Challa Suresh 3 1 Professor, Department of Mechanical Engineering, Andhra University, Visakhapatnam, Andhra
More informationSurface Integrity in Micro-Hole Drilling Using Micro-Electro Discharge Machining
Materials Transactions, Vol. 44, No. 12 (2003) pp. 2718 to 2722 #2003 The Japan Institute of Metals EXPRESS REGULAR ARTICLE Surface Integrity in Micro-Hole Drilling Using Micro-Electro Discharge Machining
More informationA study to achieve a fine surface finish in Wire-EDM
Journal of Materials Processing Technology 149 (24) 165 171 A study to achieve a fine surface finish in Wire-EDM Y.S. Liao a,, J.T. Huang b, Y.H. Chen a a Department of Mechanical Engineering, National
More informationEffect of Over Voltage on Material Removal Rate During Electrochemical Machining
Tamkang Journal of Science and Engineering, Vol. 8, No 1, pp. 23 28 (2005) 23 Effect of Over Voltage on Material Removal Rate During Electrochemical Machining S. K. Mukherjee 1, S. Kumar 1 and P. K. Srivastava
More informationNew Thermo-Physical Modeling of EDM with The Latent Heat Consumption
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 12, Issue 7 (July 2016), PP.54-63 New Thermo-Physical Modeling of EDM with The Latent
More informationOptimization of Machining Parameters in ECM of Al/B4C Composites Using Taguchi Method
International Journal of Applied Science and Engineering 2014. 12, 2: 87-97 Optimization of Machining Parameters in ECM of Al/B4C Composites Using Taguchi Method S. R. Rao a* and G. Padmanabhan b a Department
More informationCHAPTER 4 EXPERIMENTAL DESIGN. 4.1 Introduction. Experimentation plays an important role in new product design, manufacturing
CHAPTER 4 EXPERIMENTAL DESIGN 4.1 Introduction Experimentation plays an important role in new product design, manufacturing process development and process improvement. The objective in all cases may be
More informationDecision Science Letters
Decision Science Letters 4 (2015) 211 226 Contents lists available at GrowingScience Decision Science Letters homepage: www.growingscience.com/dsl Parameter selection in non-traditional machining processes
More informationDesign of arrow-head electrode in electropolishing of cylindrical part
312 Int. J. Materials and Product Technology, Vol. 20, No. 4, 2004 Design of arrow-head electrode in electropolishing of cylindrical part H. Hocheng* Department of Power Mechanical Engineering, National
More informationS. S.Mahapatra National Institute of Technology Department of Mechanical Engineering Rourkela. INDIA. Amar Patnaik.
S. S.Mahapatra and Amar Patnaik S. S.Mahapatra ssm@nitrkl.ac.in National Institute of Technology Department of Mechanical Engineering Rourkela. INDIA Amar Patnaik amar_mech@sify.com G.I.E.T Department
More informationUltrashort Pulse Laser Technology for Processing of Advanced Electronics Materials
Ultrashort Pulse Laser Technology for Processing of Advanced Electronics Materials Jim BOVATSEK *1, Rajesh PATEL *1 *1 Spectra-Physics, MKS Instruments, Inc., 3635 Peterson Way, Santa Clara, CA., 95054,
More informationThe Mathematical Modeling and Computer Simulation of Pulse Electrochemical Micromachining
The Mathematical Modeling and Computer Simulation of Pulse Electrochemical Micromachining J. Kozak, D. Gulbinowicz, and Z. Gulbinowicz Abstract The need for complex and accurate three dimensional (3-D)
More informationPrediction of performance parameters in Wire EDM of HcHcr steel using Artificial Neural Network
Prediction of performance parameters in Wire EDM of HcHcr steel using Artificial Neural Network N. G. Parmar Mechanical Engineering Department Government Polytechnic, Kheda Gujarat, India e-mail: ng_parmar@yahoo.co.in
More informationInternational Journal of Scientific & Engineering Research, Volume 5, Issue 12, December ISSN IJSER
International Journal of Scientific & Engineering Research, Volume 5, Issue 12, December-2014 29 Prediction of EDM process parameters by using Artificial Neural Network (ANN) - A Prediction Technique Mitali
More informationVOL. 11, NO. 2, JANUARY 2016 ISSN
MULTIPLE-PERFORMANCE OPTIMIZATION OF DRILLING PARAMETERS AND TOOL GEOMETRIES IN DRILLING GFRP COMPOSITE STACKS USING TAGUCHI AND GREY RELATIONAL ANALYSIS (GRA) METHOD Gallih Bagus W. 1, Bobby O. P. Soepangkat
More informationExperiment FT1: Measurement of Dielectric Constant
Experiment FT1: Measurement of Dielectric Constant Name: ID: 1. Objective: (i) To measure the dielectric constant of paper and plastic film. (ii) To examine the energy storage capacity of a practical capacitor.
More informationUniversity of Huddersfield Repository
University of Huddersfield Repository Ding, Hao, Qi, Qunfen, Scott, Paul J. and Jiang, Xiang An ANOVA method of evaluating the specification uncertainty in roughness measurement Original Citation Ding,
More informationResponse surface Methodology and Desirability Approach to Optimize EDM Parameters
, pp. 393-406 http://dx.doi.org/10.14257/ijhit.2016.9.4.34 Response surface Methodology and Desirability Approach to Optimize EDM Parameters ChittaranjanDas. V Department of Mechanical Engineering, R.V.R.&J.C.
More informationGolam Kibria 1,*, Biswanath Doloi 2, and Bijoy Bhattacharyya 2 OPEN ACCESS RESEARCH ARTICLE. 1. Introduction
Manufacturing Rev. 2014, 1, 12 Ó G. Kibria et al., Published by EDP Sciences, 2014 DOI: 10.1051/mfreview/2014011 Available online at: http://mfr.edp-open.org RESEARCH ARTICLE OPEN ACCESS Modelling and
More informationCOMPANY : ELECTRONICA MACHINE TOOLS, PUNE, INDIA
Taguchi Method Case-Study OPTIMIZATION of ELECTRIC DISCHARGE MACHINE (EDM) by Dr. P. R. Apte IIT Bombay, INDIA 8. IDENTIFY THE MAIN FUNCTION, 2. IDENTIFY THE NOISE FACTORS, TESTING CONDITIONS, AND QUALITY
More informationFUNDAMENTAL STUDY OF MAGNETIC FIELD-ASSISTED MICRO-EDM FOR NON-MAGNETIC MATERIALS KENNETH G. HEINZ, JR. THESIS
FUNDAMENTAL STUDY OF MAGNETIC FIELD-ASSISTED MICRO-EDM FOR NON-MAGNETIC MATERIALS BY KENNETH G. HEINZ, JR. THESIS Submitted in partial fulfillment of the requirements for the degree of Master of Science
More informationOptimization of Wire EDM Process Parameters of Al 6061/Al 2 O 3 /3%red mud MMC
Optimization of Wire EDM Process Parameters of Al 6061/Al 2 O 3 /3%red mud MMC Dhinesh kumar.k #1 Sivakumar.M *2, Sivakumar.K *3,Kumar.M *4 # P.G scholar, Department of Mechanical Engineering,Bannari Amman
More informationEnergy Distrihution in Electrical Discharge Machining with Graphite Electrode
Memoirs of the Faculty of Engineering, Okayama University, Vol. 34, No. 1,2, pp.19-26, March 2 Energy Distrihution in Electrical Discharge Machining with Graphite Electrode Akira OKADA*, Yoshiyuki UNO*
More informationExperimental Study on Parametric Optimization of Titanium based Alloy (Ti-6Al-4V) in Electrochemical Machining Process
Experimental Study on Parametric Optimization of Titanium based Alloy (Ti-6Al-4V) in Electrochemical Machining Process Pravin D.Babar Mechanical Engineering Department, Rajarambapu Institute of Technology
More informationOPTIMIZATION ON SURFACE ROUGHNESS OF BORING PROCESS BY VARYING DAMPER POSITION
OPTIMIZATION ON SURFACE ROUGHNESS OF BORING PROCESS BY VARYING DAMPER POSITION Wasis Nugroho, Nor Bahiyah Baba and Adi Saptari Faculty of Manufacturing Engineering Technology, TATI University College,
More informationANALYSIS OF PARAMETRIC INFLUENCE ON DRILLING USING CAD BASED SIMULATION AND DESIGN OF EXPERIMENTS
5 th International Conference on Advances in Mechanical Engineering and Mechanics ICAMEM2010 18-20 December, 2010, Hammamet, Tunisia ANALYSIS OF PARAMETRIC INFLUENCE ON DRILLING USING CAD BASED SIMULATION
More informationDesign and analysis of a piezoelectric film embedded smart cutting tool
Design and analysis of a piezoelectric film embedded smart cutting tool C Wang*, R Rakowski and K Cheng Advanced Manufacturing and Enterprise Engineering, School of Engineering and Design, Brunel University,
More informationNUMERICAL INVESTIGATION AND STATISTICAL ANALYSIS OF LASER BENDING OF TITANIUM SHEETS
5 th International & 26 th All India Manufacturing Technology, Design and Research Conference (AIMTDR 2014) December 12 th 14 th, 2014, IIT Guwahati, Assam, India NUMERICAL INVESTIGATION AND STATISTICAL
More informationFEM ANALYSIS WITH EXPERIMENTAL RESULTS TO STUDY EFFECT OF EDM PARAMETERS ON MRR OF AISI 1040 STEEL
FEM ANALYSIS WITH EXPERIMENTAL RESULTS TO STUDY EFFECT OF EDM PARAMETERS ON MRR OF AISI 1040 STEEL Imran Patel 1 & Prashant Powar 2 1PG Student, Department of Production Engineering, KIT s College of Engineering,
More informationInvestigation on Electric Discharge Machine for optimization of Surface Roughness using Response Surface Methodology approach
Investigation on Electric Discharge Machine for optimization of Surface Roughness using Response Surface Methodology approach A thesis submitted in partial fulfillment of the requirements for the degree
More informationExperimental Investigation of CNC Turning Process Parameters on AISI 1018 carbon steel
Experimental Investigation of CNC Turning Process Parameters on AISI 1018 carbon steel Bijo Mathew 1,Edin Michael 2 and Jervin Das 3 1,2,3 Faculty, Department of Mechanical Engineering, Bishop Jerome institute,kollam,india
More information