A Project for Thermodynamics II. Entitled
|
|
- Isaac Parrish
- 5 years ago
- Views:
Transcription
1 A Project for Thermodynamics II Entitled Determination of the Effect of Equivalence Ratio and Pressure on the Adiabatic Flame Temperature and Reaction "Completeness" during 75% Propane and 25% Methane Mixture Combustion Prepared by Brad Schaffer Department of Mechanical Engineering and Mechanics Drexel University August 24, 2004
2 Schaffer 2 Table of Contents: Abstract 3 Introduction..4 Methods 5 Results..7 Discussion/Conclusion.9 Appendix A 10 Appendix B 12 Appendix C 14 Appendix D 15
3 Schaffer 3 Abstract: This report explored the effects of equivalence ratio and pressure on the adiabatic flame temperature and the completeness of combustion for a mixture of twenty-five percent methane and seventy-five percent propane during its combustion with air. Completeness was measured on a percentage scale by comparing actual carbon dioxide produced with that produced during stoichiometric combustion. Any value above ninetyfive percent was considered to be complete. For the given combustion process, it was found that as pressure increased, both completeness and adiabatic flame temperature also increased. It was also found that as the equivalence ratio increased, the completeness of combustion steadily declined. However, the adiabatic flame temperature peaked when the equivalence ratio was at an intermediate value between 1.01 and 1.10 for the tested pressures of 0.01 to 1000 atm. The maximum obtainable adiabatic flame temperature for the tested values was K with a completeness of percent. This occurred at a pressure of 1000 atm and an equivalence ratio of 1.01.
4 Schaffer 4 Introduction: The combustion of hydrocarbons plays a crucial role in many aspects of our lives. Two of the largest industries that utilize the combustion hydrocarbons are the power generation and the automotive industries. Since hydrocarbon fuels are scarce resources, they must be utilized wisely. This creates the need for an understanding of how combustion processes work and a need to optimize combustion processes. The objective for this experiment was to find how equivalence ratio and pressure affect adiabatic flame temperature and completeness of combustion for the burning of a mixture of 25% CH 4 and 75% C 3 H 8 with air at the standard reference state. From these results, the optimized equivalence ratio and pressure were to be determined. The experiment s basis was from the first law of thermodynamics, conservation of energy, and the second law of thermodynamics which deals with the directionality of a reaction. Since the given system did not involve any work or heat transfer, only the change in chemical energy of the system had to be analyzed. This was done using the program STANJAN. Given a chemical equation and its reactant information, STANJAN produces the equilibrium composition and the product temperature.
5 Schaffer 5 Methods: The first step was to produce a balanced chemical equation for a perfect burn: ( ) 0.25CH C H O N 2.5CO + 3.5H O N Evaluating reactants for all equivalence ratios: CH C3H 8 + ( O N2) er er O 2 N This provided all of the necessary reactant information on a molar basis. STANJAN was then used to calculate the enthalpy of the reactants at the standard reference state.
6 Schaffer 6 er h , , , , , , , , , , , , , , , , , ,870 Finally, all reactant data was entered into STANJAN which was then used to calculate adiabatic flame temperature and the equilibrium composition for equivalence ratios ranging from 0.35 to 2.00 and pressures ranging from 0.01 atm to 1000 atm. The output data from STANJAN had two output values of interest. The first was the temperature. This temperature represented the adiabatic flame temperature since the enthalpy of the reactants, calculated in the first step, was used as the enthalpy value for calculating the products. The second output of interest was the equilibrium composition of the product. In particular, the molar amount of CO 2 was of interest because this allowed for the measurement of completeness. Completeness was measured on a percentage scale by comparing actual carbon dioxide produced with that produced during stoichiometric combustion. Any value greater than 95% was considered complete for this experiment
7 Schaffer 7 Results: AFT vs. Equivalence Ratio vs. Pressure K er atm The results showed several important correlations between adiabatic flame temperature, pressure, completeness, and equivalence ratio. The above graph shows how the equivalence ratio and pressure affect the adiabatic flame temperature. As pressure increased, the AFT also increased for all equivalency ratios. It can also be seen that the maximum obtainable AFT increases as pressure increases (please see Appendix D). When analyzing the affects of the equivalency ratio, it is seen that a slightly rich fuel air mixture produces the highest AFT. The lower the pressure the richer the mixture must be to reach the peak AFT (please see appendix C).
8 Schaffer 8 Percent Completeness er atm As the pressure increased, the completeness of combustion also increased in all cases. However, as the equivalence ratio increases, the completeness of combustion fell. This can be seen in the above graph. At equivalence ratios of 0.50 and under, the completeness of combustion was above 99.98% in all cases (pleases see appendix B). However, in these low er ranges, the AFT was only approximately 50% of the maximum AFT.
9 Schaffer 9 Discussion/Conclusion: For a given range of pressures and equivalency ratios, the adiabatic flame temperature and completeness of combustion were successfully calculated for the combustion of a methane and propane mixture. The data provided useful insight to the behavior of this combustion when two major parameters, pressure and equivalency ratio, were adjusted. Further research could include increasing the pressure range and conducting research on optimizing the ratio of methane to propane.
10 Schaffer 10 Appendix A: AFT vs. Equivalence Ratio vs. Pressure Data AFT vs. Equivalence Ratio vs. Pressure K er atm
11 AFT Pressure (atm) er Schaffer 11
12 Schaffer 12 Appendix B: Percent Completeness Data Percent Completeness er Pressure (atm)
13 Percent Completeness Pressure (atm) er Schaffer 13
14 Schaffer 14 Appendix C: Pressure vs. Optimum Equivalency Ratio Pressure vs. Optimum er er atm *Optimum er is the equivalence ratio at which the maximum AFT occurred.
15 Schaffer 15 Appendix D: Pressure vs. Maximum Adiabatic Flame Temperature Pressure vs. Max AFT K atm
Reacting Gas Mixtures
Reacting Gas Mixtures Reading Problems 15-1 15-7 15-21, 15-32, 15-51, 15-61, 15-74 15-83, 15-91, 15-93, 15-98 Introduction thermodynamic analysis of reactive mixtures is primarily an extension of the principles
More informationFundamentals of Combustion
Fundamentals of Combustion Lec 3: Chemical Thermodynamics Dr. Zayed Al-Hamamre Content Process Heat Transfer 1-3 Process Heat Transfer 1-4 Process Heat Transfer 1-5 Theoretical and Excess Air Combustion
More informationAAE COMBUSTION AND THERMOCHEMISTRY
5. COMBUSTIO AD THERMOCHEMISTRY Ch5 1 Overview Definition & mathematical determination of chemical equilibrium, Definition/determination of adiabatic flame temperature, Prediction of composition and temperature
More informationExample 14.1 Expressing Equilibrium Constants for Chemical Equations
Example 14.1 Expressing Equilibrium Constants for Chemical Equations For Practice 14.1 Express the equilibrium constant for the combustion of propane as shown by the balanced chemical equation: Example
More informationQuantity Relationships in Chemical Reactions
Chapter 10 Relationships in Chemical Reactions Section 10.1 Conversion Factors from a Chemical Equation Goal 1 The coefficients in a chemical equation give us the conversion factors to get from the number
More informationFundamentals Of Combustion (Part 1) Dr. D.P. Mishra Department of Aerospace Engineering Indian Institute of Technology, Kanpur
Fundamentals Of Combustion (Part 1) Dr. D.P. Mishra Department of Aerospace Engineering Indian Institute of Technology, Kanpur Lecture 09 Stoichiometric calculations for air-gas mixture Let us start this
More informationApply the concept of percent yield to stoichiometric problems. Methanol can be produced through the reaction of CO and H 2 in the presence of a
Apply the concept of percent yield to stoichiometric problems. Methanol can be produced through the reaction of CO and H 2 in the presence of a catalyst. CO (g) + H 2 (g) CH 3 OH (l) If 75.0 g of CO reacts
More informationCombustion: Flame Theory and Heat Produced. Arthur Anconetani Oscar Castillo Everett Henderson
Combustion: Flame Theory and Heat Produced Arthur Anconetani Oscar Castillo Everett Henderson What is a Flame?! Reaction Zone! Thermo/Chemical characteristics Types of Flame! Premixed! Diffusion! Both
More informationHeating value, adiabatic flame temperature, air factor
Heating value, adiabatic flame temperature, air factor Background heating value In a boiler fuel is burned (oxidized) to flue gas components. In this process, (chemical) energy is released and bound to
More informationAP Chemistry Chapter 16 Assignment. Part I Multiple Choice
Page 1 of 7 AP Chemistry Chapter 16 Assignment Part I Multiple Choice 1984 47. CH 4 (g) + 2 O 2 (g) CO 2 (g) + 2 H 2 O(l) H = 889.1 kj H f H 2 O(l) = 285.8 kj mol 1 H f CO 2 (g) = 393.3 kj mol 1 What is
More informationevidyarthi.in Thermodynamics Q 1.
SUBJECTIVE PROBLEMS: Q 1. Thermodynamics The enthalpy for the following reaction ( H o ) at 25 o C are given below: (i) 1/2 H 2 (g) + 1/2 O 2 (g) OH(g) 10.06 kcal (ii) H 2 (g) 2H(g) 104.18 kcal (iii) O
More informationConservation of mass: 44 kg on LHS and RHS one kmol of CO₂ produced by burning 1 kmol of C with one kmol of O₂
L20 Stoichiometry of Reactions Gore Combustion provides the heat source for many power cycles (cars, airplanes, power plants), for home heating, cooking applications, and for manufacturing from melting
More information3 Property relations and Thermochemistry
3 Property relations and Thermochemistry 3.1 Intensive and extensive properties Extensive properties depend on the amount of mass or number of moles in the system. The extensive properties are usually
More informationModule 5: Combustion Technology. Lecture 32: Fundamentals of thermochemistry
1 P age Module 5: Combustion Technology Lecture 32: Fundamentals of thermochemistry 2 P age Keywords : Heat of formation, enthalpy change, stoichiometric coefficients, exothermic reaction. Thermochemistry
More informationME 354 Tutorial, Week#13 Reacting Mixtures
ME 354 Tutorial, Week#13 Reacting Mixtures Question 1: Determine the mole fractions of the products of combustion when octane, C 8 H 18, is burned with 200% theoretical air. Also, determine the air-fuel
More informationCombustion. Indian Institute of Science Bangalore
Combustion Indian Institute of Science Bangalore Combustion Applies to a large variety of natural and artificial processes Source of energy for most of the applications today Involves exothermic chemical
More informationLaminar Premixed Flames: Flame Structure
Laminar Premixed Flames: Flame Structure Combustion Summer School 2018 Prof. Dr.-Ing. Heinz Pitsch Course Overview Part I: Fundamentals and Laminar Flames Introduction Fundamentals and mass balances of
More informationAmounts of substances can be described in different ways. One mole of a substance is the relative formula mass in ...
Q1.This question is about atoms and isotopes. (a) Atoms contain protons, neutrons and electrons. A lithium atom has the symbol Explain, in terms of sub-atomic particles, why the mass number of this lithium
More informationChemical Energetics. First Law of thermodynamics: Energy can be neither created nor destroyed but It can be converted from one form to another.
Chemical Energetics First Law of thermodynamics: Energy can be neither created nor destroyed but It can be converted from one form to another. All chemical reactions are accompanied by some form of energy
More informationSolving Stoichiometry Problems
Open the TI-Nspire document Solving_Stoichiometry_Problems.tns In this lesson you will use simulations of three combustion reactions to develop skills necessary to solve stoichiometric problems. Move to
More informationChapter 3. Stoichiometry: Calculations with Chemical Formulas and Equations
Chapter 3. Stoichiometry: Calculations with Chemical Formulas and Equations Lecture Outline 3.1 Chemical Equations The quantitative nature of chemical formulas and reactions is called stoichiometry. Lavoisier
More informationThermochemistry X.S. Bai Thermochemistry
Lecture 2 Thermochemistry Design a power plant X.S. Bai Thermochemistry When we study a combustion device, what do we want to know? heat generated power production combustion efficiency combustion control
More informationFirst Law of Thermodynamics: energy cannot be created or destroyed.
1 CHEMICAL THERMODYNAMICS ANSWERS energy = anything that has the capacity to do work work = force acting over a distance Energy (E) = Work = Force x Distance First Law of Thermodynamics: energy cannot
More informationDISCIPLINA MIEEA 2018
DISCIPLINA MIEEA 2018 Technologies of combustion Combustion definition Combustion is essentially burning, fuels react with oxygen to release energy 4 Combustion use in the world No Combustion Combustion
More informationChapter 3: Chemical Reactions and the Earth s Composition
Chapter 3: Chemical Reactions and the Earth s Composition Problems: 3.1-3.3, 3.5, 3.11-3.86, 3.95-3.115, 3.119-3.120, 3.122, 3.125-3.128, 3.132, 3.134, 3.136-3.138-3.141 3.2 The Mole Stoichiometry (STOY-key-OM-e-tree):
More informationDr Ali Jawarneh Department of Mechanical Engineering Hashemite University
Chapter 15 CHEMICAL REACTIONS Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University 2 Objectives Give an overview of fuels and combustion. Apply the conservation of mass to reacting
More informationChapter 5 Practice Multiple Choice & Free
Name Response 1. A system has an increase in internal energy, E, of 40 kj. If 20 kj of work, w, is done on the system, what is the heat change, q? a) +60 kj d) -20 kj b) +40 kj e) -60 kj c) +20 kj 2. Which
More informationLecture 6 Asymptotic Structure for Four-Step Premixed Stoichiometric Methane Flames
Lecture 6 Asymptotic Structure for Four-Step Premixed Stoichiometric Methane Flames 6.-1 Previous lecture: Asymptotic description of premixed flames based on an assumed one-step reaction. basic understanding
More informationHeat energy change revision questions
Name: Heat energy change revision questions Date: Time: Total marks available: 63 Total marks achieved: Q1. A student uses this apparatus to find the increase in temperature of water when methanol, CH
More informationAAE THERMOCHEMISTRY BASICS
5.4 THERMOCHEMISTRY BASICS Ch5 23 Energies in Chemical Reactions Enthalpy of Combustion (Reactions): Q CV H in = H reactant H out = H product REACTANTS Stoichiometric fuel-oxidizer (air) mixture at standard
More informationFuel, Air, and Combustion Thermodynamics
Chapter 3 Fuel, Air, and Combustion Thermodynamics 3.1) What is the molecular weight, enthalpy (kj/kg), and entropy (kj/kg K) of a gas mixture at P = 1000 kpa and T = 500 K, if the mixture contains the
More informationThe modelling of premixed laminar combustion in a closed vessel
INSTITUTE OF PHYSICS PUBLISHING Combust. Theory Modelling 8 (2004) 721 743 COMBUSTION THEORY AND MODELLING PII: S1364-7830(04)69216-3 The modelling of premixed laminar combustion in a closed vessel Khizer
More informationGestão de Sistemas Energéticos 2017/2018
Gestão de Sistemas Energéticos 2017/2018 Exergy Analysis Prof. Tânia Sousa taniasousa@tecnico.ulisboa.pt Conceptualizing Chemical Exergy C a H b O c enters the control volume at T 0, p 0. O 2 and CO 2,
More informationCOMBUSTION OF FUEL 12:57:42
COMBUSTION OF FUEL The burning of fuel in presence of air is known as combustion. It is a chemical reaction taking place between fuel and oxygen at temperature above ignition temperature. Heat is released
More informationChemistry. Chapter 17
Chemistry Chapter 17 Chemical Equations C+O 2 CO 2 C (s) +O 2 (g) CO 2 (g) Reactants on left, products on right Each are balanced because same number of atoms of reactants as products Balancing Chemical
More informationRocket Propulsion. Reacting Flow Issues
Rocket Propulsion Reacting Flow Issues Rocket Thermochemistry- Combustor Calculations c* (T o /) /2 Must include effect of product dissociation for rocket chamber calculations will decrease T o and reduce
More informationFundamentals Of Combustion (Part 1) Dr. D.P. Mishra Department of Aerospace Engineering Indian Institute of Technology, Kanpur
Fundamentals Of Combustion (Part 1) Dr. D.P. Mishra Department of Aerospace Engineering Indian Institute of Technology, Kanpur Lecture 10 Mixture fraction calculation for diffusion flames Let us start
More informationChapter 3: STOICHIOMETRY: MASS, FORMULAS, AND REACTIONS
Chapter 3: STOICHIOMETRY: MASS, FORMULAS, AND REACTIONS Problems: 3.1-3.8, 3.11, 3.14-3.90, 3.103-3.120, 3.122-3.125, 3.128-3.131, 3.134, 3.137-36.138, 3.140-3.142 3.2 THE MOLE Stoichiometry (STOY-key-OM-e-tree):
More informationASSORTED STOICHIOMETRY PRACTICE PROBLEMS PART I
ASSORTED STOICHIOMETRY PRACTICE PROBLEMS PART I (1) A 1.2156-gram sample of a mixture of CaCO 3 and Na 2 SO 4 was analyzed by dissolving the sample and completely precipitating the Ca 2+ as CaC 2 O 4.
More informationQ1. (a) (i) Which acid should the student add to sodium hydroxide solution to make sodium sulphate? Formula:... (1)
Q1. (a) (i) Which acid should the student add to sodium hydroxide solution to make sodium sulphate?... acid (ii) Use the table on the Data Sheet to help you to write the formula of sodium sulphate. Formula:...
More informationStoichiometry Rockets
Stoichiometry Rockets The objective of this lab is to to: calculate the needed volume of fuel to react with a given volume of gas and result in a productive explosion determine the heat of the reaction
More informationActivity Sheet Chapter 6, Lesson 1 What is a Chemical Reaction?
Activity Sheet Chapter 6, Lesson 1 What is a Chemical Reaction? Name Date DEMNSTRATIN 1. Your teacher lit a candle and told you that this was a chemical reaction. What are the reactants in this chemical
More informationThe names and formulae of three hydrocarbons in the same homologous series are:... (1) Which homologous series contains ethane, propane and butane?
Q1. This question is about hydrocarbons. (a) The names and formulae of three hydrocarbons in the same homologous series are: Ethane C 2 H 6 Propane C 3 H 8 Butane C 4 H 10 The next member in the series
More informationUNIT 15: THERMODYNAMICS
UNIT 15: THERMODYNAMICS ENTHALPY, DH ENTROPY, DS GIBBS FREE ENERGY, DG ENTHALPY, DH Energy Changes in Reactions Heat is the transfer of thermal energy between two bodies that are at different temperatures.
More informationChapter 19 Chemical Thermodynamics
Chapter 19. Chemical Thermodynamics Sample Exercise 19.2 (p. 819) Elemental mercury is a silver liquid at room temperature. Its normal freezing point is -38.9 o C, and its molar enthalpy of fusion is H
More informationLecture 7 Flame Extinction and Flamability Limits
Lecture 7 Flame Extinction and Flamability Limits 7.-1 Lean and rich flammability limits are a function of temperature and pressure of the original mixture. Flammability limits of methane and hydrogen
More informationLet a system undergo changes from a state 1 to state 2.
ME 410 Day 11 Topics First Law of Thermodynamics Applied to Combustion Constant olume Combustion Constant ressure Combustion Enthalpy of Formation Heating alues of Fuels 1. The First Law of Thermodynamics
More informationChapter 15. In the preceding chapters we limited our consideration to CHEMICAL REACTIONS. Objectives
Chapter 15 CHEMICAL REACTIONS In the preceding chapters we limited our consideration to nonreacting systems systems whose chemical composition remains unchanged during a process. This was the case even
More informationChemistry 2000 Lecture 9: Entropy and the second law of thermodynamics
Chemistry 2000 Lecture 9: Entropy and the second law of thermodynamics Marc R. Roussel January 23, 2018 Marc R. Roussel Entropy and the second law January 23, 2018 1 / 29 States in thermodynamics The thermodynamic
More informationGeneral Chemistry I Concepts
Thermodynamics Thermodynamics The Three Laws of Thermodynamics (18.1) Spontaneous Processes (18.2) Entropy (18.3) The Second Law of Thermodynamics (18.4) Gibbs Free Energy (18.5) Free Energy and Chemical
More informationClass XI Chapter 6 Thermodynamics Question 6.1: Choose the correct answer. A thermodynamic state function is a quantity (i) used to determine heat changes (ii) whose value is independent of path (iii)
More informationAP Chemistry A. Allan Chapter Six Notes - Thermochemistry
AP Chemistry A. Allan Chapter Six Notes - Thermochemistry 6.1 The Nature of Energy A. Definition 1. Energy is the capacity to do work (or to produce heat*) a. Work is a force acting over a distance (moving
More information1. (25 points) C 6 H O 2 6CO 2 + 7H 2 O C 6 H O 2 6CO + 7H 2 O
MEEBAL Exam 2 November 2013 Show all work in your blue book. Points will be deducted if steps leading to answers are not shown. No work outside blue books (such as writing on the flow sheets) will be considered.
More informationLecture 37. Heat of Reaction. 1 st Law Analysis of Combustion Systems
Department of Mechanical Engineering ME 322 Mechanical Engineering hermodynamics Heat of eaction Lecture 37 1 st Law Analysis of Combustion Systems Combustion System Analysis Consider the complete combustion
More informationExothermic process is any process that gives off heat transfers thermal energy from the system to the surroundings. H 2 O (l) + energy
Exothermic process is any process that gives off heat transfers thermal energy from the system to the surroundings. H 2 O (g) H 2 O (l) + energy Endothermic process is any process in which heat has to
More informationChapter 9. Chemical Quantities
Chapter 9 Chemical Quantities Section 9.1 Information Given by Chemical Equations A balanced chemical equation gives relative numbers (or moles) of reactant and product molecules that participate in a
More informationChemical Kinetics: NOx Mechanisms
Mole Fraction Temperature (K) Chemical Kinetics: Nx Mechanisms Jerry Seitzman. 5.15.1.5 CH4 H HC x 1 Temperature Methane Flame.1..3 Distance (cm) 15 1 5 KineticsNx -1 Nx Formation Already pointed out that
More informationChapter 6 Problems: 9, 19, 24, 25, 26, 27, 31-33, 37, 39, 43, 45, 47, 48, 53, 55, 57, 59, 65, 67, 73, 78-82, 85, 89, 93
Chapter 6 Problems: 9, 19, 24, 25, 26, 27, 31-33, 37, 39, 43, 45, 47, 48, 53, 55, 57, 59, 65, 67, 73, 78-82, 85, 89, 93 Chapter 6 Thermochemistry The study of chemical reactions and the energy changes
More informationAP* Thermodynamics Free Response Questions page 1. Essay Questions
AP* Thermodynamics Free Response Questions page 1 Essay Questions 1991 The reaction represented above is a reversible reaction. BCl 3 (g) + NH 3 (g) Cl 3 BNH 3 (s) (a) Predict the sign of the entropy change,
More informationHe measures the steady temperature of the water before adding the lithium iodide.
1 A student uses this apparatus to measure the temperature change when lithium iodide dissolves in water. 100 g of water He measures the steady temperature of the water before adding the lithium iodide.
More informationStandard enthalpies and standard Gibbs energies of formation 4. Calculating enthalpy changes and Gibbs energy changes for reactions 5
Chemical Reactions as Sources of Energy Part 1: Thermodynamics Contents Standard enthalpies and standard Gibbs energies of formation 4 Calculating enthalpy changes and Gibbs energy changes for reactions
More informationChemical Reactions. Chapter 17
Chemical Reactions Chapter 17 Chemical Equations C+O 2 CO 2 C (s) +O 2 (g) CO 2 (g) Reactants on left, products on right Each are balanced because same number of atoms of reactants as products Some equations
More informationSTOICHIOMETRY ANALOGY
STOICHIOMETRY ANALOGY Stoichiometry is the quantitative relationship between the reactants and products in a balanced chemical equation. Stoichiometry allows chemists to predict how much of a reactant
More informationChemistry 30 Review Sessions THERMOCHEMISTRY
Chemistry 30 Review Sessions THERMOCHEMISTRY Curriculum bullets Use Q = mcδt to analyze heat transfer. Use calorimetry data to determine the enthalpy changes in chemical reactions. Calorimeters rely on
More informationA First Course on Kinetics and Reaction Engineering Example 1.2
Example 1.2 Problem Purpose This example shows how to determine when it is permissible to choose a basis for your calculations. It also illustrates how to use reaction progress variables and the initial
More informationL = 6.02 x mol Determine the number of particles and the amount of substance (in moles)
1.1 The Mole 1.1.1 - Apply the mole concept to substances A mole is the name given to a certain quantity. It represents 6.02 x 10 23 particles. This number is also known as Avogadro's constant, symbolised
More informationQuantitative Relationships in Chemical Reactions Chapter 7
Quantitative Relationships in Chemical Reactions Chapter 7 The burning of charcoal releases heat (thermal energy) that grills our food. But the combustion of charcoal and fossil fuels also releases CO
More informationChapter 8: Quantities in Chemical Reactions
C h e m i s t r y 1 2 C h 8 : Q u a n t i t i e s i n C h e m i c a l R e a c t i o n s P a g e 1 Chapter 8: Quantities in Chemical Reactions Read Chapter 8 and Check MasteringChemistry due dates. Stoichiometry:
More informationINTERNAL COMBUSTION ENGINE (SKMV 3413)
INTERNAL COMBUSTION ENGINE (SKMV 3413) Dr. Mohd Farid bin Muhamad Said Room : Block P21, Level 1, Automotive Development Centre (ADC) Tel : 07-5535449 Email: mfarid@fkm.utm.my THERMOCHEMISTRY IC engine
More informationChemical Equations 10/30/13. Types of Chemical Reactions. Types of Chemical Reactions. Types of Chemical Reactions. Types of Chemical Reactions
Chemical Equations A chemical equation just like a mathematical equation is a way to express, in symbolic form, the reactions occurring in a chemical system. n Balancing chemical equations n Reaction stoichiometry
More informationChem 5 Fall This reaction is a (circle ONE) (2) Acid-Base Reaction Precipitation Reaction Redox Reaction
1. (16) Draw Lewis structures for FOUR of the following molecules or ions. Include all important resonance forms. Clearly label EVERY atom with its formal charge. The FIRST eight structures that you write
More informationThe Reaction module. Table of Contents
Table of contents The module calculates the thermochemical properties of a species, a mixture of species or a chemical reaction. accesses only compound databases. assumes all gases are ideal and ignores
More informationBurning a Hydrocarbon II
Burning a Hydrocarbon II Name Lab Section Problem Statement: How are the masses of products limited by the amounts of reactants? I. Data Collection: A. Go to http://cheminfo.chem.ou.edu/~mra/home.html
More informationEnthalpy and Adiabatic Changes
Enthalpy and Adiabatic Changes Chapter 2 of Atkins: The First Law: Concepts Sections 2.5-2.6 of Atkins (7th & 8th editions) Enthalpy Definition of Enthalpy Measurement of Enthalpy Variation of Enthalpy
More information5.7 Quantity Relationships in Chemical Reactions (Stoichiometry)
5.7 Quantity Relationships in Chemical Reactions (Stoichiometry) We have previously learned that atoms combine in simple whole number ratios to form compounds. However, to perform a chemical reaction,
More informationUsual Atomic Charges of Main Group Elements
Usual Atomic Charges of Main Group Elements +1 +2 +3 +4 +5 +6 +7-5 -4-3 -2-1 Examples SO 3 sulfur trioxide CO 2 carbon dioxide Al 2 O 3 aluminum trioxide IF 7 iodine heptafluoride Fig. 2-6, p.63 Chemical
More informationN L N G : C O M B U S T I O N
N L N G : C O M B U S T I O N G R A N T I N G R A M 6 T H D E C E M B E R 2 0 1 7 This short lecture provides an introduction into the basic principles of combustion and some of the background to the use
More informationThe Reaction module. Cu) Isothermal standard state reactions (oxidation of copper) of pure (Al)) Two phase single component equilibrium (ideal
Table of contents The module Use to calculate the thermochemical properties of a species or a chemical reaction. accesses only compound type databases. Note that assumes all gases to be ideal and ignores
More informationSection 3.0. The 1 st Law of Thermodynamics. (CHANG text Chapter 4) 3.1. Revisiting Heat Capacities Definitions and Concepts
Section 3.0. The 1 st Law of Thermodynamics (CHANG text Chapter 4) 3.1. Revisiting Heat Capacities 3.2. Definitions and Concepts 3.3. The First Law of THERMODYNAMICS 3.4. Enthalpy 3.5. Adiabatic Expansion
More informationUnit 5 Percent Composition, Empirical Formulas, and Reactions
Chemistry 1 West Linn High School Unit 5 Packet and Goals Name: Period: Unit 5 Percent Composition, Empirical Formulas, and Reactions Unit Goals: As you work through this unit, you should be able to: 1.
More informationThermodynamics. For the process to occur under adiabatic conditions, the correct condition is: (iii) q = 0. (iv) = 0
Thermodynamics Choose the correct answer. A thermodynamic state function is a quantity (i) used to determine heat changes (ii) whose value is independent of path (iii) used to determine pressure volume
More informationNational 4/5 Chemistry
National 4/5 hemistry omework Unit 2 Nature s hemistry Please do not write on these booklets questions should be answered in homework jotters. Part 1 Introduction to Unit 2 1. You are given three unlabelled
More informationBalancing chemical reaction equations (stoichiometry)
Balancing chemical reaction equations (stoichiometry) This worksheet and all related files are licensed under the Creative Commons Attribution License, version 1.0. To view a copy of this license, visit
More informationWORKSHEET #1. Dougherty Valley HS AP Chemistry Hess s Law Problems
Dougherty Valley HS AP Chemistry Hess s Law Problems WORKSHEET #1 1. Calculate the standard enthalpy change, ΔH o, for the formation of 1 mol of strontium carbonate (the material that gives the red color
More informationINTEGRATED SIMULATION MODEL FOR COMPOSITION AND PROPERTIES OF GASES IN HYDROGEN FUELED ENGINE
International Journal of Automotive and Mechanical Engineering (IJAME) ISSN: 2229-8649 (Print); ISSN: 2180-1606 (Online); Volume 8, pp. 1242-1255, July-December 2013 Universiti Malaysia Pahang DOI: http://dx.doi.org/10.15282/ijame.8.2013.14.1242-1255
More informationThermochemistry-Part 1
Brad Collins Thermochemistry-Part 1 Chapter 7 Thermochemistry Thermodynamics: The study of energy Thermochemistry: The study of energy in chemical reactions Energy: The capacity to do work Work = force
More informationand mol of Cl 2 was heated in a vessel of fixed volume to a constant temperature, the following reaction reached equilibrium.
Q1. When a mixture of 0.45 mol of PCl and 0.68 mol of Cl was heated in a vessel of fixed volume to a constant temperature, the following reaction reached equilibrium. PCl + Cl PCl 5 H = 9 kj mol 1 At equilibrium,
More informationChapter 17.3 Entropy and Spontaneity Objectives Define entropy and examine its statistical nature Predict the sign of entropy changes for phase
Chapter 17.3 Entropy and Spontaneity Objectives Define entropy and examine its statistical nature Predict the sign of entropy changes for phase changes Apply the second law of thermodynamics to chemical
More informationAP Chemistry: Chapter 3 Notes Outline
AP Chemistry: Chapter 3 Notes Outline Objectives: Balance chemical equations Use dimensional analysis to solve stoichiometric problems Use dimensional analysis to do limiting reactant problems Use dimensional
More informationEnergy is the capacity to do work
1 of 10 After completing this chapter, you should, at a minimum, be able to do the following. This information can be found in my lecture notes for this and other chapters and also in your text. Correctly
More information128 One problem... PATH. The amount of energy required for a process depends on how the process is carried out.
128 One problem... PATH. The amount of energy required for a process depends on how the process is carried out. Example: Driving from Florence to Columbia. How much energy is required? (gas) Jeep Cherokee
More informationThermodynamics Qualifying Exam Study Material
Thermodynamics Qualifying Exam Study Material The candidate is expected to have a thorough understanding of undergraduate engineering thermodynamics topics. These topics are listed below for clarification.
More information2013, 2011, 2009, 2008 AP
Lecture 15 Thermodynamics I Heat vs. Temperature Enthalpy and Work Endothermic and Exothermic Reactions Average Bond Enthalpy Thermodynamics The relationship between chemical reactions and heat. What causes
More informationQ1. Methane and oxygen react together to produce carbon dioxide and water.
Q1. Methane and oxygen react together to produce carbon dioxide and water. The methane gas will not burn in oxygen until a flame is applied, but once lit it continues to burn. (a) Explain why energy must
More informationHeat Changes in Chemical Processes
Heat Changes in Chemical Processes 1. Zeroeth Law of Thermodynamics: Two systems at thermal equilibrium with a third system are in thermal equilibrium with each other. Paraphrase: Systems in thermal equilibrium
More information3 Stoichiometry: Calculations with Chemical Formulas and Equations
3 Stoichiometry: Calculations with Chemical Formulas and Equations 3.1 Chemical Equations Balance chemical equations. 3. Simple Patterns of Reactivity Predict products of a chemical reaction in a combination
More informationChapter 4. Fundamentals of Material Balance
Chapter 4 Fundamentals of Material Balance Introduction to Chapter 4 1) In chapter 4 we will present methods for organizing known information about process variables, setting up martial balance equations,
More informationEFFECT OF CARBON DIOXIDE, ARGON AND HYDROCARBON FUELS ON THE STABILITY OF HYDROGEN JET FLAMES
EFFECT OF CARBON DIOXIDE, ARGON AND HYDROCARBON FUELS ON THE STABILITY OF HYDROGEN JET FLAMES Wu, Y 1, Al-Rahbi, I. S. 1, Lu, Y 1. and Kalghatgi, G. T. 2 1 Department of Chemical and Process Engineering,
More informationEnthalpy Chapter 5.3-4,7
Enthalpy Chapter 5.3-4,7 heat transfer in (endothermic), +q heat transfer out (exothermic), -q SYSTEM E = q + w w transfer in (+w) w transfer out (-w) Internal Energy at Constant Volume E = E K + E P ΔE
More information