Lecture 7. Pile Analysis
|
|
- Lindsey Snow
- 5 years ago
- Views:
Transcription
1 Lecture Release Pile Analysis 2012 ANSYS, Inc. February 9, Release 14.5
2 Pile definition in Mechanical - There are a number of methods that can be used to analyze piled foundations in ANSYS Mechanical: SPLINTER (a standalone nonlinear solver that was originally developed as part of the ASAS suite) Matrix definition (MAT27) Spring definition (COMBIN14) Direct Definition of P-Y and T-Z curves (COMBIN39) The SPLINTER method will be described here 2012 ANSYS, Inc. February 9, Release 14.5
3 Soil-pile interaction - Soils are classified in four different types based on their particle size and shape: Soil Type Particle Size (mm) Particle Shape Gravel 2 60 Granular Sand Granular Silt Granular Clay < Flat plate - The lateral resistance of the soil near the mud line is significant for many reasons, and the effects of this resistance of scour and soil disturbance during pile installation should be considered ANSYS, Inc. February 9, Release 14.5
4 Soil-pile interaction (cont.) - The flexibility of the soil makes the soil-structure system less stiff than if the structure were on a fixed base. This loss of stiffness can increase ωf which can increase the dynamic response of the system (Watt et al. 1976) - Three important features need to be considered: a. Soil is a nonlinear material (stiffness decreases with increasing shear stress) b. Soil strength and stiffness is affected by repeated cycles of load c. Soil exhibits damping, which increases with increasing shear amplitude, when subjected to cyclic loading 2012 ANSYS, Inc. February 9, Release 14.5
5 Soil-pile interaction (cont.) - The nonlinear foundation technique in SPLINTER utilises a FE representation of the pile and soil system as shown below. The soil stiffness is modelled with spring elements in the lateral and vertical direction - The soil springs are characterised by a nonlinear force-deflection curve. These curves are known as the P-Y and T-Z curves for lateral and axial (skin friction) behaviour respectively - It is because of the nonlinear nature of the soil that SPLINTER carries out an iterative solution technique, each iteration taking an assumed, or calculated, value for the soil spring stiffness based on the previous iteration (see Newton-Raphson method) 2012 ANSYS, Inc. February 9, Release 14.5
6 Soil-pile interaction (cont.) - Soils are highly nonlinear in their behaviour, Young s, Shear and Bulk Modulus varies with loading. The nonlinearity is caused by the soil particles moving relative to one another as the load is applied. - For preliminary decisions the relevant values in BS5930, BS1377 and BS8004 may be adequate. - In situ measurements are necessary with soil samples at later stages Chakrabarti, SK (2005) Handbook Offshore Engring, Vol ANSYS, Inc. February 9, Release 14.5
7 Soil-pile interaction (cont.) - The generation of lateral soil resistance deflection (P-Y) curves should be constructed using stress-strain data from samples. Various methods of estimating P-Y curves for different soil types exist in the literature: Matlock (1970), Reese & Cox (1975), O Neill & Murchinson (1983) LATERAL CAPACITY FOR SOFT CLAY The p-y curves for the short-term static load case can be generated from the following table p/pu y/yc p u cx 3c X J p u 9c D y 2.5 D c c and for X X R where pu is ult resistance, psi c = undrained shear strength for undisturbed clay samples (psi) γ = eff unit wgt of soil (lb/in3) D = pile dia (in.) J = dimensionless empirical factor ranging from 0.25 to 0.5 X = depth below the sea bed (in.) 1.00 XR = depth below sea bed to which the reduced resistance zone extends (in.) Min values approx. 2.5D p = actual lateral resistance (psi) y = actual lateral deflection (in.) εc = strain which occurs at one-half the max stress on lab undrained compression tests of undisturbed soil samples 2012 ANSYS, Inc. February 9, Release 14.5
8 Soil-pile interaction (cont.) LATERAL CAPACITY FOR STIFF CLAY The ultimate bearing capacity of stiff clay (c > 96kPa) would vary between 8c<Pu<12c LATERAL CAPACITY FOR SAND The ultimate lateral capacity for sand in shallow depths is determined from P us while for deep depths is given from ( C1H C2D) H P ud C D H 3 Where Pu = ult resistance (psi) γ = εff soil wgt (lb/in3) Η = depth below sea bed(in) φ = angle of internal friction of sand (deg) C1, C2, C3 coeff determined from tables (see next slide) D = average pile dia from surface to depth (in) 2012 ANSYS, Inc. February 9, Release 14.5
9 Soil-pile interaction (cont.) Once the previous values are found the load deflection curves for sand are given by kh P( y) APu tanh y APu Where A = factor to account for cyclic or static loading Pu = ult resistance (psi) k = initial modulus of subgrade reaction (lb/in3) See fig below Η = depth (in) y = lateral deflection (in) Relative density is an indication of the packing in comparison with the 2012 ANSYS, Inc. February 9, min (0% relative density) and max (100% relative density) densities achievable Release 14.5
10 Soil-pile interaction (cont.) - Two solution methods exist for determining the soil stiffness from P-Y and T-Z curves, namely Tangent and Secant stiffness. In general the tangent stiffness method (default) will converge faster. - Soil properties are assumed to vary linearly between the defined points, for points outside the defined range linear extrapolation is assumed. - Both symmetric and asymmetric curves may be defined for soil data - The option to include/ignore pile self weight, select method to use in derivation of soil stiffness, include/exclude second order effects is given in PILEGEN command 2012 ANSYS, Inc. February 9, Release 14.5
11 Soil-pile interaction (cont.) - Extreme weather phenomena and the passage of waves induce pressure changes on the seabed that may cause remoulding and a reduction in shear strength. This in turn can lead to shear failure in soft sediments on sloping ground - Mudslides (depressions in the seabed) should be considered in the design process and a piled structure should withstand a mudslide through the lowest plan bracing level - This problem can be taken into account in SPLINTER when defining the soil properties (file_soil.txt). This ascii file should be in the solver files directory (RC on Solution>Open Solver Files Directory). For the syntax of this file see // Advanced Analysis Guide // 15. Soil-Pile-Structure Analysis // Soil Data Definition and Examples 2012 ANSYS, Inc. February 9, Release 14.5
12 Nonlinear solution using linear solvers - In a nonlinear analysis, the response cannot be predicted directly with a set of linear equations - However, a nonlinear structure can be analyzed using an iterative series of linear approximations, with corrections - ANSYS uses an iterative process called the Newton-Raphson Method. Each iteration is known as an equilibrium iteration Load F K1 K2 1 K4 K A full Newton-Raphson iterative analysis for one increment of load. (Four iterations shown) u Displacement 2012 ANSYS, Inc. February 9, Release 14.5
13 Nonlinear solution using linear solvers The actual relationship between load and displacement (shown as a dotted line) is not known beforehand. Consequently, a series of linear approximations with corrections is performed. This is a simplified explanation of the Newton-Raphson method (shown as solid red lines) In the Newton-Raphson Method, the total Newton-Raphson Method load F a is applied in iteration 1. The result F is x 1. From the displacements, the internal 4 F 3 4 forces F 1 can be calculated. If F a F 1, then F the system is not in equilibrium. Hence, a new stiffness matrix (slope of red line) is F 1 1 calculated based on the current conditions. The difference of F a - F 1 is the out-of-balance or residual forces. The residual forces must be small enough for the solution to converge x This process is repeated until F a F i. In this example, after iteration 4, 1 the x2 system x3 x4 achieves equilibrium and the solution is said to be converged 2012 ANSYS, Inc. February 9, Release 14.5
14 Nonlinear solution using linear solvers The difference between external and internal loads, {F a } - {F nr }, is called the residual. It is a measure of the force imbalance in the structure. The goal is to iterate until the residual becomes acceptably small; that is, until the solution is converged. When convergence is achieved, the solution is in equilibrium, within an acceptable tolerance. {F a } {F nr } { F a F nr 2012 ANSYS, Inc. February 9, Release 14.5 u
15 SPLINTER To use SPLINTER in Workbench Mechanical, the process required on a jacket model is: Define named selections for each Pile cap node named Pile1, Pile2 etc. Request approx. 5 loadsteps and set up with small time increment (the loadsteps are needed to allow iteration on soil curves; the small time step is needed as the ocean loading is time dependant) Insert a command object to define the ocean Insert a command object to define the piles Insert a command object to solve each iteration 2012 ANSYS, Inc. February 9, Release 14.5
16 Workshop 5 Pile Analysis Workshop 5 Add piles to a jacket structure Goal: Use command objects & become acquainted with MAPDL Use local parameters in command object Study the necessary input for SPLINTER (strata, curves, mudslide etc.) Get to know the analysis settings for a soil-pile analysis Study the output from SPLINTER 2012 ANSYS, Inc. February 9, Release 14.5
Prof. Dr.-Ing. Martin Achmus Institute of Soil Mechanics, Foundation Engineering and Waterpower Engineering. Monopile design
Prof. Dr.-Ing. Martin Achmus Institute of Soil Mechanics, Foundation Engineering and Waterpower Engineering Monopile design Addis Ababa, September 2010 Monopile design Presentation structure: Design proofs
More informationAxially Loaded Piles
Axially Loaded Piles 1 t- Curve Method using Finite Element Analysis The stress-strain relationship for an axially loaded pile can be described through three loading mechanisms: axial deformation in the
More informationCourse in. Geometric nonlinearity. Nonlinear FEM. Computational Mechanics, AAU, Esbjerg
Course in Nonlinear FEM Geometric nonlinearity Nonlinear FEM Outline Lecture 1 Introduction Lecture 2 Geometric nonlinearity Lecture 3 Material nonlinearity Lecture 4 Material nonlinearity it continued
More informationGapping effects on the lateral stiffness of piles in cohesive soil
Gapping effects on the lateral stiffness of piles in cohesive soil Satyawan Pranjoto Engineering Geology, Auckland, New Zealand. M. J. Pender Department of Civil and Environmental Engineering, University
More informationPILE SOIL INTERACTION MOMENT AREA METHOD
Pile IGC Soil 2009, Interaction Moment Guntur, INDIA Area Method PILE SOIL INTERACTION MOMENT AREA METHOD D.M. Dewaikar Professor, Department of Civil Engineering, IIT Bombay, Mumbai 400 076, India. E-mail:
More informationProject. First Saved Monday, June 27, 2011 Last Saved Wednesday, June 29, 2011 Product Version 13.0 Release
Project First Saved Monday, June 27, 2011 Last Saved Wednesday, June 29, 2011 Product Version 13.0 Release Contents Units Model (A4, B4) o Geometry! Solid Bodies! Parts! Parts! Body Groups! Parts! Parts
More informationTC211 Workshop CALIBRATION OF RIGID INCLUSION PARAMETERS BASED ON. Jérôme Racinais. September 15, 2015 PRESSUMETER TEST RESULTS
Jérôme Racinais September 15, 215 TC211 Workshop CALIBRATION OF RIGID INCLUSION PARAMETERS BASED ON PRESSUMETER TEST RESULTS Table of contents 1. Reminder about pressuremeter tests 2. General behaviour
More informationTheory of Shear Strength
MAJ 1013 ADVANCED SOIL MECHANICS Theory of Shear Strength Prepared by, Dr. Hetty 1 Strength of different materials Steel Concrete Soil Tensile strength Compressive strength Shear strength Complex behavior
More informationCPT Guide 5 th Edition. CPT Applications - Deep Foundations. Gregg Drilling & Testing, Inc. Dr. Peter K. Robertson Webinar # /2/2013
Gregg Drilling & Testing, Inc. Site Investigation Experts CPT Applications - Deep Foundations Dr. Peter K. Robertson Webinar #6 2013 CPT Guide 5 th Edition Robertson & Cabal (Robertson) 5 th Edition 2012
More informationLandslide FE Stability Analysis
Landslide FE Stability Analysis L. Kellezi Dept. of Geotechnical Engineering, GEO-Danish Geotechnical Institute, Denmark S. Allkja Altea & Geostudio 2000, Albania P. B. Hansen Dept. of Geotechnical Engineering,
More informationINTRODUCTION TO STATIC ANALYSIS PDPI 2013
INTRODUCTION TO STATIC ANALYSIS PDPI 2013 What is Pile Capacity? When we load a pile until IT Fails what is IT Strength Considerations Two Failure Modes 1. Pile structural failure controlled by allowable
More informationResonant Column and Torsional Cyclic Shear System
Resonant Column and Torsional Cyclic Shear System Combined Resonant Column (RC) & Torsional Cyclic Shear (TCS) Test apparatus to determinate with saturated soil : Shear Modulus Damping Modulus versus Shear
More informationTheory of Shear Strength
SKAA 1713 SOIL MECHANICS Theory of Shear Strength Prepared by, Dr. Hetty 1 SOIL STRENGTH DEFINITION Shear strength of a soil is the maximum internal resistance to applied shearing forces The maximum or
More informationAnalysis of Pile Foundation Subjected to Lateral and Vertical Loads
Analysis of Pile Foundation Subjected to Lateral and Vertical Loads Thadapaneni Kanakeswararao 1, B.Ganesh 2 1,2 Department of soil mechanics and foundation engg, Lenora college of Engineering and technology,
More informationCHAPTER 8 ANALYSES OF THE LATERAL LOAD TESTS AT THE ROUTE 351 BRIDGE
CHAPTER ANALYSES OF THE LATERAL LOAD TESTS AT THE ROUTE 351 BRIDGE.1 INTRODUCTION An important objective of this research is to determine whether accurate analyses of the lateral load-deflection behavior
More informationChapter 5 Shear Strength of Soil
Page 5 Chapter 5 Shear Strength of Soil. The internal resistance per unit area that the soil mass can offer to resist failure and sliding along any plane inside it is called (a) strength (b) shear strength
More informationImplementation of Laterally Loaded Piles in Multi-Layer Soils
Implementation of Laterally Loaded Piles in Multi-Layer Soils JTRP SPR- 3261 Final SAC meeting SAC members Mir Zaheer and Keith Hoernschemeyer Purdue University Introduction Analysis developed for the
More information1.8 Unconfined Compression Test
1-49 1.8 Unconfined Compression Test - It gives a quick and simple measurement of the undrained strength of cohesive, undisturbed soil specimens. 1) Testing method i) Trimming a sample. Length-diameter
More informationCHAPTER 8 CALCULATION THEORY
CHAPTER 8 CALCULATION THEORY. Volume 2 CHAPTER 8 CALCULATION THEORY Detailed in this chapter: the theories behind the program the equations and methods that are use to perform the analyses. CONTENTS CHAPTER
More informationChapter (11) Pile Foundations
Chapter (11) Introduction Piles are structural members that are made of steel, concrete, or timber. They are used to build pile foundations (classified as deep foundations) which cost more than shallow
More informationReport No. K-TRAN: KU-10-2 FINAL REPORT November 2013
Report No. K-TRAN: KU-10-2 FINAL REPORT November 2013 Capacity of Scour-Damaged Bridges, Part 2: Integrated Analysis Program (IAP) A Program for the Analysis of Lateral Performance of Pile-Supported Structures
More informationEngineeringmanuals. Part2
Engineeringmanuals Part2 Engineering manuals for GEO5 programs Part 2 Chapter 1-12, refer to Engineering Manual Part 1 Chapter 13. Pile Foundations Introduction... 2 Chapter 14. Analysis of vertical load-bearing
More informationFinite Element analysis of Laterally Loaded Piles on Sloping Ground
Indian Geotechnical Journal, 41(3), 2011, 155-161 Technical Note Finite Element analysis of Laterally Loaded Piles on Sloping Ground K. Muthukkumaran 1 and N. Almas Begum 2 Key words Lateral load, finite
More informationCPT Data Interpretation Theory Manual
CPT Data Interpretation Theory Manual 2016 Rocscience Inc. Table of Contents 1 Introduction... 3 2 Soil Parameter Interpretation... 5 3 Soil Profiling... 11 3.1 Non-Normalized SBT Charts... 11 3.2 Normalized
More informationApplication of cyclic accumulation models for undrained and partially drained general boundary value problems
Application of cyclic accumulation models for undrained and partially drained general boundary value problems A. M. Page Risueño Yngres Dag 2014, May 15 th 2014 Introduction Cyclic loads in geotechnical
More informationAnalysis of pile foundation Simplified methods to analyse the pile foundation under lateral and vertical loads
Analysis of pile foundation Simplified methods to analyse the pile foundation under lateral and vertical loads 1 Kanakeswararao Thadapaneni, 2 Sarikonda Venkata sivaraju, 3 Ravi teja Grandhi 1 PG Student,
More information2D Liquefaction Analysis for Bridge Abutment
D Liquefaction Analysis for Bridge Abutment Tutorial by Angel Francisco Martinez Integrated Solver Optimized for the next generation 64-bit platform Finite Element Solutions for Geotechnical Engineering
More informationPre-failure Deformability of Geomaterials. Hsin-yu Shan Dept. of Civil Engineering National Chiao Tung University
Pre-failure Deformability of Geomaterials Hsin-yu Shan Dept. of Civil Engineering National Chiao Tung University Strain Levels Strain at failure Sand Clay Rock Distribution of strain of soil in the field
More informationD1. A normally consolidated clay has the following void ratio e versus effective stress σ relationship obtained in an oedometer test.
(d) COMPRESSIBILITY AND CONSOLIDATION D1. A normally consolidated clay has the following void ratio e versus effective stress σ relationship obtained in an oedometer test. (a) Plot the e - σ curve. (b)
More informationUSER S MANUAL 1D Seismic Site Response Analysis Example University of California: San Diego August 30, 2017
USER S MANUAL 1D Seismic Site Response Analysis Example http://www.soilquake.net/ucsdsoilmodels/ University of California: San Diego August 30, 2017 Table of Contents USER'S MANUAL TABLE OF CONTENTS Page
More informationInvestigation of Pile- Soil Interaction Subjected to Lateral Loads in Layered Soils
American J. of Engineering and Applied Sciences (): 76-8, 008 ISSN 9-700 008 Science Publications Investigation of Pile- Soil Interaction Subjected to Lateral Loads in Layered Soils A. Avaei, Abdoul R.
More informationNEW DOWN-HOLE PENETROMETER (DHP-CIGMAT) FOR CONSTRUCTION APPLICATIONS
NEW DOWN-HOLE PENETROMETER (DHP-CIGMAT) FOR CONSTRUCTION APPLICATIONS 1 2 C. Vipulanandan 1, Ph.D., M. ASCE and Omer F. Usluogullari 2 Chairman, Professor, Director of Center for Innovative Grouting Materials
More information8.1. What is meant by the shear strength of soils? Solution 8.1 Shear strength of a soil is its internal resistance to shearing stresses.
8.1. What is meant by the shear strength of soils? Solution 8.1 Shear strength of a soil is its internal resistance to shearing stresses. 8.2. Some soils show a peak shear strength. Why and what type(s)
More informationDeep Foundations 2. Load Capacity of a Single Pile
Deep Foundations 2 Load Capacity of a Single Pile All calculations of pile capacity are approximate because it is almost impossible to account for the variability of soil types and the differences in the
More informationCollapsible Soils Definitions
Collapsible Soils Definitions Collapsible soils are also known as metastable soils. They are unsaturated soils that undergo a large volume change upon saturation. The sudden and usually large volume change
More informationTable 3. Empirical Coefficients for BS 8002 equation. A (degrees) Rounded Sub-angular. 2 Angular. B (degrees) Uniform Moderate grading.
Hatanaka and Uchida (1996); ' 20N 20 12N 20 ' 45 A lower bound for the above equation is given as; 12N 15 ' 45 Table 3. Empirical Coefficients for BS 8002 equation A Angularity 1) A (degrees) Rounded 0
More informationReciprocal of the initial shear stiffness of the interface K si under initial loading; reciprocal of the initial tangent modulus E i of the soil
Appendix F Notation a b B C c C k C N C s C u C wt C θ D r D 1 D 2 D 10 D 30 Reciprocal of the initial shear stiffness of the interface K si under initial loading; reciprocal of the initial tangent modulus
More informationNONLINEAR CHARACTERISTICS OF THE PILE-SOIL SYSTEM UNDER VERTICAL VIBRATION
IGC 2009, Guntur, INDIA NONLINEAR CHARACTERISTICS OF THE PILE-SOIL SYSTEM UNDER VERTICAL VIBRATION B. Manna Lecturer, Civil Engineering Department, National Institute of Technology, Rourkela 769008, India.
More informationNon-linear and time-dependent material models in Mentat & MARC. Tutorial with Background and Exercises
Non-linear and time-dependent material models in Mentat & MARC Tutorial with Background and Exercises Eindhoven University of Technology Department of Mechanical Engineering Piet Schreurs July 7, 2009
More informationCh 5 Strength and Stiffness of Sands
Ch. 5 - Strength and Stiffness of Sand Page 1 Ch 5 Strength and Stiffness of Sands Reading Assignment Ch. 5 Lecture Notes Sections 5.1-5.7 (Salgado) Other Materials Homework Assignment Problems 5-9, 5-12,
More informationAnalysis of a single pile settlement
Engineering manual No. 14 Updated: 06/2018 Analysis of a single pile settlement Program: Pile File: Demo_manual_14.gpi The objective of this engineering manual is to explain the application of the GEO
More informationReinforced Soil Structures Reinforced Soil Walls. Prof K. Rajagopal Department of Civil Engineering IIT Madras, Chennai
Geosynthetics and Reinforced Soil Structures Reinforced Soil Walls continued Prof K. Rajagopal Department of Civil Engineering IIT Madras, Chennai e-mail: gopalkr@iitm.ac.inac in Outline of the Lecture
More informationUSER S MANUAL 1D Seismic Site Response Analysis Example University of California: San Diego August 30, 2017
USER S MANUAL 1D Seismic Site Response Analysis Example http://www.soilquake.net/ucsdsoilmodels/ University of California: San Diego August 30, 2017 Table of Contents USER'S MANUAL TABLE OF CONTENTS Page
More informationPGroupN background theory
12/12/03 Dr Francesco Basile, Geomarc Ltd PGroupN background theory Estimation of the deformations and load distributions in a group of piles generally requires the use of computer-based methods of analysis.
More informationPile-Soil Interaction in Unsaturated Soil Conditions
University of New Hampshire University of New Hampshire Scholars' Repository Honors Theses and Capstones Student Scholarship Spring 2014 Pile-Soil Interaction in Unsaturated Soil Conditions Megan Hamilton
More informationComparison of shear pile force and moment in slippage reinforced with shear pile Mona Mohamadi 1, Abolfazl Eslami, Farhad Nabizade 1 1. Department of Technology, Guilan University, Iran. Department of
More information!!!!!! Piles Capacity Reference Manual
Piles Capacity Reference Manual Foreword July 26, 2014 Piles Capacity is simply the pocket calculator for deep foundation designers dealing with pile bearing capacity of cast-in-place bored piles (also
More informationSHEAR STRENGTH OF SOIL
Soil Failure Criteria SHEAR STRENGTH OF SOIL Knowledge about the shear strength of soil important for the analysis of: Bearing capacity of foundations, Slope stability, Lateral pressure on retaining structures,
More informationUSER S MANUAL. 1D Seismic Site Response Analysis Example. University of California: San Diego.
USER S MANUAL 1D Seismic Site Response Analysis Example http://www.soilquake.net/ucsdsoilmodels/ University of California: San Diego August 2, 2017 Table of Contents USER'S MANUAL TABLE OF CONTENTS Page
More informationSoil strength. the strength depends on the applied stress. water pressures are required
Soil Strength Soil strength u Soils are essentially frictional materials the strength depends on the applied stress u Strength is controlled by effective stresses water pressures are required u Soil strength
More informationGeotechnical issues in seismic assessments: When do I need a geotechnical specialist?
Geotechnical issues in seismic assessments: When do I need a geotechnical specialist? B.H. Rama & S.J. Palmer Tonkin & Taylor Ltd (T+T), Wellington, New Zealand. 2016 NZSEE Conference ABSTRACT: The Canterbury
More informationShear Strength of Soils
Shear Strength of Soils STRESSES IN A SOIL ELEMENT t s v Analyze Effective Stresses (s ) Load carried by Soil t Where: s H t t s H s = t f = s v = s H = t = s v Stresses in a Soil Element after Figure
More informationCh 4a Stress, Strain and Shearing
Ch. 4a - Stress, Strain, Shearing Page 1 Ch 4a Stress, Strain and Shearing Reading Assignment Ch. 4a Lecture Notes Sections 4.1-4.3 (Salgado) Other Materials Handout 4 Homework Assignment 3 Problems 4-13,
More informationTIME-DEPENDENT BEHAVIOR OF PILE UNDER LATERAL LOAD USING THE BOUNDING SURFACE MODEL
TIME-DEPENDENT BEHAVIOR OF PILE UNDER LATERAL LOAD USING THE BOUNDING SURFACE MODEL Qassun S. Mohammed Shafiqu and Maarib M. Ahmed Al-Sammaraey Department of Civil Engineering, Nahrain University, Iraq
More informationChapter (12) Instructor : Dr. Jehad Hamad
Chapter (12) Instructor : Dr. Jehad Hamad 2017-2016 Chapter Outlines Shear strength in soils Direct shear test Unconfined Compression Test Tri-axial Test Shear Strength The strength of a material is the
More informationJ. Paul Guyer, P.E., R.A.
J. Paul Guyer, P.E., R.A. Paul Guyer is a registered mechanical engineer, civil engineer, fire protection engineer and architect with over 35 years experience in the design of buildings and related infrastructure.
More informationDynamic Analysis to Study Soil-Pile Interaction Effects
by Pallavi Ravishankar, Neelima Satyam in Indexed in Scopus Compendex and Geobase Elsevier, Chemical Abstract Services-USA, Geo-Ref Information Services- USA, List B of Scientific Journals, Poland, Directory
More informationSHEAR STRENGTH OF SOIL
SHEAR STRENGTH OF SOIL Necessity of studying Shear Strength of soils : Soil failure usually occurs in the form of shearing along internal surface within the soil. Shear Strength: Thus, structural strength
More informationMechanical properties 1 Elastic behaviour of materials
MME131: Lecture 13 Mechanical properties 1 Elastic behaviour of materials A. K. M. B. Rashid Professor, Department of MME BUET, Dhaka Today s Topics Deformation of material under the action of a mechanical
More informationHKIE-GD Workshop on Foundation Engineering 7 May Shallow Foundations. Dr Limin Zhang Hong Kong University of Science and Technology
HKIE-GD Workshop on Foundation Engineering 7 May 2011 Shallow Foundations Dr Limin Zhang Hong Kong University of Science and Technology 1 Outline Summary of design requirements Load eccentricity Bearing
More informationANALYSIS OF LATERALLY LOADED FIXED HEADED SINGLE FLOATING PILE IN MULTILAYERED SOIL USING BEF APPROACH
INDIAN GEOTECHNICAL SOCIETY, KOLKATA CHAPTER GEOTECHNICS FOR INFRASTRUCTURE DEVELOPMENT KOLKATA 11 th 12 th March 2016, Kolkata, West Bengal, India ANALYSIS OF LATERALLY LOADED FIXED HEADED SINGLE FLOATING
More informationTABLE OF CONTENTS CHAPTER TITLE PAGE TITLE PAGE DECLARATION DEDIDATION ACKNOWLEDGEMENTS ABSTRACT ABSTRAK
TABLE OF CONTENTS CHAPTER TITLE PAGE TITLE PAGE DECLARATION DEDIDATION ACKNOWLEDGEMENTS ABSTRACT ABSTRAK TABLE OF CONTENTS LIST OF TABLE LIST OF FIGURES LIST OF SYMBOLS LIST OF APENDICES i ii iii iv v
More informationRock Berm Restraint of an Untrenched Pipeline on Soft Clay
Rock Berm Restraint of an Untrenched Pipeline on Soft Clay J.-C. Ballard, P.H. Yonatan and M.J. Rattley, Fugro GeoConsulting A. Griffiths, Shell UK Limited ABSTRACT This paper discusses soil structure
More informationSoil Properties - II
Soil Properties - II Amit Prashant Indian Institute of Technology andhinagar Short Course on eotechnical Aspects of Earthquake Engineering 04 08 March, 2013 Seismic Waves Earthquake Rock Near the ground
More informationSOME OBSERVATIONS RELATED TO LIQUEFACTION SUSCEPTIBILITY OF SILTY SOILS
SOME OBSERVATIONS RELATED TO LIQUEFACTION SUSCEPTIBILITY OF SILTY SOILS Upul ATUKORALA 1, Dharma WIJEWICKREME 2 And Norman MCCAMMON 3 SUMMARY The liquefaction susceptibility of silty soils has not received
More informationNonlinear pushover analysis for pile foundations
Proc. 18 th NZGS Geotechnical Symposium on Soil-Structure Interaction. Ed. CY Chin, Auckland Michael Pender Department of Civil and Environmental Engineering, University of Auckland Keywords: piles, lateral
More informationPiles Capacity Reference Manual
Piles Capacity Reference Manual hetge hetge geotechnics on the go Piles Capacity Reference Manual January 3, 2013 Version: PC-1.3.130103 hetge LLC Moscow Virginia Istanbul E info@hetge.com W www.hetge.com
More informationProf. B V S Viswanadham, Department of Civil Engineering, IIT Bombay
56 Module 4: Lecture 7 on Stress-strain relationship and Shear strength of soils Contents Stress state, Mohr s circle analysis and Pole, Principal stressspace, Stress pathsin p-q space; Mohr-Coulomb failure
More informationModule 3. DYNAMIC SOIL PROPERTIES (Lectures 10 to 16)
Module 3 DYNAMIC SOIL PROPERTIES (Lectures 10 to 16) Lecture 15 Topics 3.6 STRESS-STRAIN BEHAVIOR OF CYCLICALLY LOADED SOILS 3.7 SOME BASIC ASPECTS OF PARTICULATE MATTER BEHAVIOR 3.8 EQUIVALENT LINEAR
More informationOPTIMAL SHAKEDOWN ANALYSIS OF LATERALLY LOADED PILE WITH LIMITED RESIDUAL STRAIN ENERGY
INTERNATIONAL JOURNAL OF OPTIMIZATION IN CIVIL ENGINEERING Int. J. Optim. Civil Eng., 2018; 8(3):347-355 OPTIMAL SHAKEDOWN ANALYSIS OF LATERALLY LOADED PILE WITH LIMITED RESIDUAL STRAIN ENERGY M. Movahedi
More informationBiaxial Analysis of General Shaped Base Plates
Biaxial Analysis of General Shaped Base Plates R. GONZALO ORELLANA 1 Summary: A linear model is used for the contact stresses calculation between a steel base plate and a concrete foundation. It is also
More informationDynamic Analyses of an Earthfill Dam on Over-Consolidated Silt with Cyclic Strain Softening
Keynote Lecture: Dynamic Analyses of an Earthfill Dam on Over-Consolidated Silt with Cyclic Strain Softening W.D. Liam Finn University of British Columbia, BC, Canada Guoxi Wu BC Hydro, Burnaby, BC, Canada
More informationCopyright. magazine. bearing capacity and modulus of subgrade reaction? Modulus of Subgrade Reaction (Ks)
Structural Design design issues for structural engineers Correlation between Soil Bearing Capacity and Modulus of Subgrade Reaction By Apurba Tribedi Apurba Tribedi is a Senior Product Manager at Bentley.
More informationNumerical Modelling of Dynamic Earth Force Transmission to Underground Structures
Numerical Modelling of Dynamic Earth Force Transmission to Underground Structures N. Kodama Waseda Institute for Advanced Study, Waseda University, Japan K. Komiya Chiba Institute of Technology, Japan
More informationInterpretation of Pile Integrity Test (PIT) Results
Annual Transactions of IESL, pp. 78-84, 26 The Institution of Engineers, Sri Lanka Interpretation of Pile Integrity Test (PIT) Results H. S. Thilakasiri Abstract: A defect present in a pile will severely
More informationPILE LOAD TEST IN OLD ALLUVIUM
An evening talk organized by GeoSS PILE LOAD TEST IN OLD ALLUVIUM Wong Kai Sin 25 August 2016 1 PILE LOAD TEST IN OLD ALLUVIUM 1.Should we accept or reject the test results? 2.What are the expected unit
More informationLaboratory Testing Total & Effective Stress Analysis
SKAA 1713 SOIL MECHANICS Laboratory Testing Total & Effective Stress Analysis Prepared by: Dr. Hetty Mohr Coulomb failure criterion with Mohr circle of stress 2 ' 2 ' ' ' 3 ' 1 ' 3 ' 1 Cot Sin c ' ' 2
More informationSTUDY OF THE BEHAVIOR OF PILE GROUPS IN LIQUEFIED SOILS
STUDY OF THE BEHAVIOR OF PILE GROUPS IN LIQUEFIED SOILS Shin-Tower Wang 1, Luis Vasquez 2, and Lymon C. Reese 3, Honorary Member,, ASCE ABSTRACT : 1&2 President & Project Manager, Ensoft, Inc. Email: ensoft@ensoftinc.com
More informationIN SITU TESTING TECHNOLOGY FOR FOUNDATION & EARTHQUAKE ENGINEERING. Wesley Spang, Ph.D., P.E. AGRA Earth & Environmental, Inc.
IN SITU TESTING TECHNOLOGY FOR FOUNDATION & EARTHQUAKE ENGINEERING Wesley Spang, Ph.D., P.E. AGRA Earth & Environmental, Inc. Portland, Oregon In situ testing of soil, which essentially consists of evaluating
More informationEvaluation of short piles bearing capacity subjected to lateral loading in sandy soil
Evaluation of short piles bearing capacity subjected to lateral loading in sandy soil [Jafar Bolouri Bazaz, Javad Keshavarz] Abstract Almost all types of piles are subjected to lateral loads. In many cases,
More informationGuidelines on Foundation Loading and Deformation Due to Liquefaction Induced Lateral Spreading
Guidelines on Foundation Loading and Deformation Due to Liquefaction Induced Lateral Spreading February, 2011 1 INTRODUCTION Past earthquakes offer many examples of bridges that either collapsed or incurred
More informationSCALE EFFECTS IN LATERAL LOAD RESPONSE OF LARGE DIAMETER MONOPILES
GeoDenver 2007, February 18 to 21, Denver, USA 1 SCALE EFFECTS IN LATERAL LOAD RESPONSE OF LARGE DIAMETER MONOPILES K. Lesny, 1 S.G. Paikowsky 2 and A. Gurbuz 2 1 Institute of Soil Mechanics and Foundation
More informationAdvanced Lateral Spread Modeling
Adv. Liquefaction Modeling Page 1 Advanced Lateral Spread Modeling Reading Assignment Lecture Notes Other Materials Homework Assignment 1. Complete FLAC model 10a.pdf 2. Modify the example in FLAC model
More informationSoil Behaviour in Earthquake Geotechnics
Soil Behaviour in Earthquake Geotechnics KENJI ISHIHARA Department of Civil Engineering Science University of Tokyo This publication was supported by a generous donation from the Daido Life Foundation
More informationCyclic lateral response of piles in dry sand: Effect of pile slenderness
Cyclic lateral response of piles in dry sand: Effect of pile slenderness Rafa S. 1, Rouaz I. 1,Bouaicha A. 1, Abed El Hamid A. 1 Rafa.sidali@gmail.com 1 National Center for Studies and Integrated Researches
More informationVerification of a Micropile Foundation
Engineering manual No. 36 Update 02/2018 Verification of a Micropile Foundation Program: File: Pile Group Demo_manual_en_36.gsp The objective of this engineering manual is to explain the application of
More information(Refer Slide Time: 02:18)
Geology and Soil Mechanics Prof. P. Ghosh Department of Civil Engineering Indian Institute of Technology Kanpur Lecture 40 Shear Strength of Soil - C Keywords: Shear strength of soil, direct shear test,
More informationCPT: Geopractica Contracting (Pty) Ltd Total depth: m, Date:
The plot below presents the cross correlation coeficient between the raw qc and fs values (as measured on the field). X axes presents the lag distance (one lag is the distance between two sucessive CPT
More informationHarmonized European standards for construction in Egypt
Harmonized European standards for construction in Egypt EN 1998 - Design of structures for earthquake resistance Jean-Armand Calgaro Chairman of CEN/TC250 Organised with the support of the Egyptian Organization
More informationChapter 5. Vibration Analysis. Workbench - Mechanical Introduction ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved.
Workbench - Mechanical Introduction 12.0 Chapter 5 Vibration Analysis 5-1 Chapter Overview In this chapter, performing free vibration analyses in Simulation will be covered. In Simulation, performing a
More informationLoading capacity of yielding connections used in steel arch roadway supports
Ground Support 2013 Y. Potvin and B. Brady (eds) 2013 Australian Centre for Geomechanics, Perth, ISBN 978-0-9806154-7-0 https://papers.acg.uwa.edu.au/p/1304_31_horyl/ Loading capacity of yielding connections
More informationSHEAR STRENGTH OF SOIL UNCONFINED COMPRESSION TEST
SHEAR STRENGTH OF SOIL DEFINITION The shear strength of the soil mass is the internal resistance per unit area that the soil mass can offer to resist failure and sliding along any plane inside it. INTRODUCTION
More informationAN ABSTRACT OF THE THESIS OF
AN ABSTRACT OF THE THESIS OF Nasim Adami for the degree of Master of Science in Civil Engineering presented on October 28, 213. Title: Development of an ACIP Pile-Specific Load-Displacement Model. Abstract
More informationFoundation models for the dynamic response of offshore wind turbines
Marine Renewable Energy Conference (MAREC), Newcastle, UK, September 00. Foundation models for the dynamic response of offshore wind turbines. M.B. Zaaijer, MSc Delft University of Technology, The Netherlands
More informationSoil and Rock Strength. Chapter 8 Shear Strength. Steel Strength. Concrete Strength. Dr. Talat Bader May Steel. Concrete.
Chapter 8 Shear Strength Dr. Talat Bader May 2006 Soil and Rock Strength Unconfined compressive strength (MPa) Steel Concrete 20 100 250 750 0.001 0.01 Soil 0.1 1.0 10 Rock 100 250 F y = 250 to 750 MPa
More informationNUMERICAL ANALYSIS OF A PILE SUBJECTED TO LATERAL LOADS
IGC 009, Guntur, INDIA NUMERICAL ANALYSIS OF A PILE SUBJECTED TO LATERAL LOADS Mohammed Younus Ahmed Graduate Student, Earthquake Engineering Research Center, IIIT Hyderabad, Gachibowli, Hyderabad 3, India.
More informationUsing the Timoshenko Beam Bond Model: Example Problem
Using the Timoshenko Beam Bond Model: Example Problem Authors: Nick J. BROWN John P. MORRISSEY Jin Y. OOI School of Engineering, University of Edinburgh Jian-Fei CHEN School of Planning, Architecture and
More informationGründungen von Offshore Windenergieanlagen: Von der Planung bis zur Lebensdauerüberwachung
Gründungen von Offshore Windenergieanlagen: Von der Planung bis zur Lebensdauerüberwachung Dr.-Ing. Fabian Kirsch GuD Geotechnik und Dynamik Consult GmbH, Berlin Offshoretage, 18. März 2016, TU Berlin
More informationCAEFEM v9.5 Information
CAEFEM v9.5 Information Concurrent Analysis Corporation, 50 Via Ricardo, Thousand Oaks, CA 91320 USA Tel. (805) 375 1060, Fax (805) 375 1061 email: info@caefem.com or support@caefem.com Web: http://www.caefem.com
More information4 Undrained Cylindrical Cavity Expansion in a Cam-Clay Medium
Undrained Cylindrical Cavity Expansion in a Cam-Clay Medium 4-1 4 Undrained Cylindrical Cavity Expansion in a Cam-Clay Medium 4.1 Problem Statement The stress and pore pressure changes due to the expansion
More information