Analyzing & Testing Business Unit. Tau-R Mode for Advanced DSC Analysis Applications Newsletter 1/ /09, Dr. Stefan Schmölzer
|
|
- Edward Baldwin
- 5 years ago
- Views:
Transcription
1 Analyzing & Testing Business Unit Tau-R Mode for Advanced DSC Analysis Applications Newsletter 1/2009 7/09, Dr. Stefan Schmölzer
2 Tau-R Mode for Advanced DSC Analysis Why is a correction of DSC measurements useful? In Differential Scanning Calorimetry, the temperature change of a sample in a crucible is measured during heating and compared to a reference (empty crucible). The heat flow is calculated on the basis of this temperature difference curve. If the sample and reference are the same, then equal heat flows are passing through both the reference and the sample, which means that the heat flow difference is zero. When the sample changes state (e.g. melting, evaporation, crystallization, etc.) due to heating (or also cooling), this is detected as a difference in temperature and the DSC curve shows a difference in heat flow. An example for such a DSC signal is the melting of a sample depicted in Figure 1. An endothermal effect can be measured for melting. On closer examination of the measured DSC data, it becomes clear that the curve shape does not exactly reflect the heat flow occurring during a phase transformation of the sample. The onset temperature marks the beginning of the melting of the sample; when the peak temperature is reached, the sample is completely molten. curve shape and reality is that after reaching the peak position, the signal does not immediately drop to zero. This, however, should be the case since the sample is already completely molten at this point and no longer needs any further energy. Therefore, the DSC curve evidently incorporates information not only about the sample but also from the instrument. To overcome this discrepancy, the tau-r correction has been developed. This correction method is based on two essential correction factors: the thermal resistance R and the time constant tau. The peak temperature does not correspond to the melting temperature of the sample, although the sample temperature should be the same as the melting temperature. Another discrepancy between the Fig. 1: Endothermal effect for the melting process 2
3 Tau-R Correction The following figure illustrates the influence of the thermal resistance R on the DSC signal. If the thermal contact is poor (Fig. 2a), melting takes a longer time. As a result, the DSC curve shows a broader, lower peak when recorded against the reference temperature. If the thermal contact is good (Fig. 2b), on the other hand, Differential Scanning Calorimetry yields a sharp peak. This means that the increase in the measured signal is a function of the thermal resistance. The area below the curves, however, is equal in both cases and corresponds to the melting enthalpy. For DSC correction, the fact that the sample temperature remains constant during the melting process is taken into consideration. The corrected DSC signal recorded against the sample temperature now shows a vertical increase in the DSC signal for melting, for example, which reflects the expected course of the melting process. The second parameter for the tau-r correction is the correction according to the time constant, tau. This is also an instrument-specific correction parameter. The theoretical background can be described as follows. The heat flow signal measured by means of DSC does not show only the heat released (or used) from the sample. In addition, the heat flow is also dependent upon the heat transfer as an instrument function. The measured signal F(t) can be depicted as the following mathematical function: where f(t) delivers the percentage of heat released from the sample. g(t) is the heat flow as a function of the instrument and can be described with the help of an exponential function of the form g(t) = exp (-t/tau). Fig 2: a) poor thermal contact b) good thermal contact 3
4 Application of the Tau-R Correction in the heat flow signal starting when melting begins. The maximum is reached when the sample is entirely molten. Then, the DSC signal slowly decreases exponentially toward zero, as a function of the time constants of the instrument. Fig. 3: Influence of the time constants tau on the DSC signals If this DSC signal is now corrected according to the tau time constant, a signal is obtained which drops back to zero immediately after reaching the peak (black curve). If the correction according to the thermal resistance, R, is now also taken into consideration (blue curve), a sharp peak is obtained for the melting process exhibiting a steep increase on its left slope and a steep decrease on its right slope. The influences on the shape of the melting peak caused by the instrument are therefore eliminated. To illustrate the influence of the tau time constant on the DSC signal of a sample, Figure 3 shows measured DSC signals with tau time constants of differing size. For a corrected measuring curve, the signal to the right of the peak position should equal zero, i.e. no more heat is being released or used. The result of such a correction is that the influence of the measuring instrument on the peak shape is eliminated and information is therefore only gathered about the sample and the processes occurring during phase transition. The red curve in Figure 4 represents an uncorrected DSC measuring curve for a melting process. The curve shape shows a slow increase Fig. 4: Application of the tau-r correction 4
5 Execution of a Tau-R Correction For determination of the correction parameters tau (time constant) and R (thermal resistance), it is necessary to measure the melting process of pure metals. Based on the measuring curve obtained, the parameters can be calculated in the analysis with the NETZSCH Proteus fi software under Evaluation -> Time Const. And Therm. Resistance. These parameters are determined for several metals and then saved. The calibration sets used in the temperature and sensitivity calibration can also be employed for the tau-r calibration. Under menu item Extras -> tau-r Calibration, a table will be opened where these parameters are recorded and saved as a correction file. This correction file can be used to correct measurements carried out under the same conditions, such as instrument type, furnace type, sensor type, crucible type, atmosphere and purge gas. The determination and creation of a correction file must be done only once for each instrument used, as long as the above-mentioned parameters are kept constant. Fig. 5: Establishment of a tau-r correction file 5
6 Example for the Application of the Tau-R Correction 1. Pharmaceutical Industry Ibuprofen is a drug classified as a non-steroidal antirheumatic agent which is employed for treating pain, inflammation and fever. DSC is an indispensable measuring method for the characterization of pharmaceuticals; the tau-r correction yields the highest in precision and correct characteristic values in this field. Fig. 6: DSC curve of Ibuprofen 2. Chemical Industry Differential Scanning Calorimetry is used in all areas where the accurate and exact characterization of substances and materials is needed. The DSC curve in Figure 6 shows that even small and overlapping effects like the melting of Hexatriacontane can be resolved. The tau-r correction additionally allows even more precise conclusions to be drawn and yields accurate values for material characterization. Fig. 7: DSC curve of Hexatriacontane 6
TAWN tests for quantitatively measuring the resolution and sensitivity of DSCs (version 2.1)
TAWN tests for quantitatively measuring the resolution and sensitivity of DSCs (version 2.1) 1. Introduction There are many properties that characterise the performance of differential scanning calorimeters
More informationHigh Pressure DSC Differential Scanning Calorimeter
High Pressure DSC Differential Scanning Calorimeter Introduction The Differential Scanning Calorimetry (DSC) is the most popular thermal analysis technique to measure endothermic and exothermic transitions
More informationThermal Methods of Analysis
Thermal Methods of Analysis Calorie-something we know What is calorie? Can you see or touch a calorie? How is it measured? Working out in gym Change in weight Loss of calories-burning of fat? (10 km=500calories/9cal
More informationA Thermal Analysis Technique That Combines Differential Scanning Calorimetry and Light Microscopy
A Thermal Analysis Technique That Combines Differential Scanning Calorimetry and Light Microscopy Thermal analysis by structural characterization (TASC) combines with differential scanning calorimetry
More informationAPPLICATION NOTE. Characterization and Classification of Recycled Polyamides by Means of Identify. Dr. Ekkehard Füglein
APPLICATION NOTE Characterization and Classification of Recycled Polyamides by Dr. Ekkehard Füglein Introduction In the field of thermal analysis up to now, researchers had to compare own data with printed
More informationAPPLICATION NOTE. Investigation of Alkali Salts with the STA 449 F5 Jupiter. Dr. Alexander Schindler and Dr. Michael Schöneich.
APPLICATION NOTE Investigation of Alkali Salts with the STA 449 F5 Jupiter Dr. Alexander Schindler and Dr. Michael Schöneich Introduction While analytical techniques such as EDX or ICP-MS provide a detailed
More informationDSC PT 10. Applications
DSC PT 10 DSC PT 10 The differential scanning calorimetry method is widely used to examine and characterize substances, mixtures, and materials. This technique is internationally standardized under DIN
More informationDSC AND TG/DTA AS PROBLEM-SOLVING TOOLS: CHARACTERIZATION OF PHARMACEUTICAL COMPOUNDS
DSC AND TG/DTA AS PROBLEM-SOLVING TOOLS: CHARACTERIZATION OF PHARMACEUTICAL COMPOUNDS Problem A scientist working for a major pharmaceutical R&D center is having difficulties in interpreting the DSC results
More informationNutshells of Thermal Analysis. Heat it up! Burn it! Thermal Analysis
Nutshells of Thermal Analysis Heat it up! Burn it! 1 Thermal Analysis Thermal Analaysis (TA) Techniques Abbreviations Full Names Measure DSC Differential Scanning Calorimetry Heat difference DMA Dynamic
More informationThermal Methods of Analysis Theory, General Techniques and Applications. Prof. Tarek A. Fayed
Thermal Methods of Analysis Theory, General Techniques and Applications Prof. Tarek A. Fayed 1- General introduction and theory: Thermal analysis (TA) is a group of physical techniques in which the chemical
More informationCalorimetry. Chapter 2. Differential Scanning heat flux calorimetry
Chapter 2 Calorimetry In this Chapter, the technique of differential scanning heat flux calorimetry is explained. We used a salt, of which the heat capacity is well-known, NaF, to test the equipment. After
More informationCH3511 EXPERIMENT: Determination of Thermal Properties Using a Differential Scanning Calorimeter
CH3511 EXPERIMENT: Determination of Thermal Properties Using a Differential Scanning Calorimeter INTRODUCTION A Mettler Toledo 823E Differential Scanning Calorimeter (DSC) will be used to determine the
More informationCalorimetry: differential scanning calorimetry (DSC), isothermal titration calorimetry (ITC)
Calorimetry: differential scanning calorimetry (DSC), isothermal titration calorimetry (ITC) Dr. Yin Li Department of Biophysics, Medical School University of Pecs Thermal Analysis IUPAC definition - a
More informationISO INTERNATIONAL STANDARD. Plastics Differential scanning calorimetry (DSC) Part 4: Determination of specific heat capacity
INTERNATIONAL STANDARD ISO 11357-4 First edition 2005-09-15 Plastics Differential scanning calorimetry (DSC) Part 4: Determination of specific heat capacity Plastiques Analyse calorimétrique différentielle
More informationTOPEM the new advanced multi-frequency TMDSC technique
Thermal Analysis TOPEM the new advanced multi-frequency TMDSC technique TMDSC methods allow both temperature-dependent and time-dependent processes to be separated. The basic idea of TOPEM is to overlay
More informationPCM specific heat capacity c p (T) measurements
PCM specific heat capacity c p (T) measurements DSC on PCM Workshop AIT, Vienna, 04. - 05. April 2016 Daniel Lager Engineer Energy Department - Sustainable Thermal Energy Systems AIT Austrian Institute
More informationUnit 4: Gas Laws. Matter and Phase Changes
Unit 4: Gas Laws Matter and Phase Changes ENERGY and matter What is 에너지 A fundamental property of the universe that cannot be easily defined. Energy No one knows what energy is, only what it does or has
More informationThermal Analysis Premium
Thermal Analysis Premium HP DSC 2+ STAR e System Innovative Technology Versatile Modularity Swiss Quality DSC Measurements under Pressure for Accelerated Materials Testing Double Safety System The Right
More informationCharacterization of Solid State Drugs by Calorimetry
Characterization of Solid State Drugs by Calorimetry Christin T. Choma TA Instruments, 109 Lukens Drive, New Castle, DE 19720, USA Drug product development and manufacture requires numerous studies to
More informationChapter 31. Thermal Methods
Chapter 31. Thermal Methods Thermal analysis: Physical property of a substance or its reaction products is measured as a function of temperature. * TGA: Thermogravimetric Analysis ( 熱重分析法 ) * DTA: Differential
More information5.2 Thermal analysis Thermal analysis
5.2 Thermal analysis 5.2.1 Thermal analysis Techniques in which a physical property of a substance is measured as a function of temperature whilst the substance is subjected to a controlled temperature
More informationChem Page IX - 1 LAB MANUAL Differential Scanning Calorimetry 09_dsc131.docx EXPERIMENT IX
Chem 366-3 Page IX - 1 LAB MANUAL Differential Scanning Calorimetry 09_dsc131.docx EXPERIMENT IX KINETICS OF DECOMPOSITION OF SODIUM BICARBONATE; A DIFFERENTIAL SCANNING CALORIMETRY EXPERIMENT 1. Purpose
More informationDifferential Scanning Calorimetry
CH 2252 Instrumental Methods of Analysis Unit III Differential Scanning Calorimetry M. Subramanian Assistant Professor Department of Chemical Engineering Sri Sivasubramaniya Nadar College of Engineering
More informationCHEM*3440. Thermal Methods. Thermogravimetry. Instrumental Components. Chemical Instrumentation. Thermal Analysis. Topic 14
Thermal Methods We will examine three thermal analytical techniques: Thermogravimetric Analysis (TGA) CHEM*3440 Chemical Instrumentation Topic 14 Thermal Analysis Differential Thermal Analysis (DTA) Differential
More informationA NEW MEASUREMENT AND EVALUATION METHOD FOR DSC OF PCM SAMPLES
A NEW MEASUREMENT AND EVALUATION METHOD FOR DSC OF PCM SAMPLES H Mehling, E Günther, S Hiebler, Bavarian Center for Applied Energy Research (ZAE Bayern), Walther-Meißner-Str. 6, D-85748 Garching, Germany.
More informationMatter changes phase when energy is added or removed
Section 12.4 Phase Changes Explain how the addition and removal of energy can cause a phase change. Interpret a phase diagram. Matter changes phase when energy is added or removed Energy Changes Accompanying
More informationNucleation Behavior of Polypropylene with a Nan-O-Sil Additive Dr. Previn Shah, Rheoplast Associates
Nucleation Behavior of Polypropylene with a Nan-O-Sil Additive Dr. Previn Shah, Rheoplast Associates James Browne Applications Scientist TA Instruments 159 Lukens Drive New Castle, DE 1972 (32) 427-415
More informationDEVELOPMENT OF IMPROVED METHODS FOR CHARACTERISING THE CURE OF COMPOSITE MATERIALS
20 th International Conference on Composite Materials Copenhagen, 19-24 th July 2015 DEVELOPMENT OF IMPROVED METHODS FOR CHARACTERISING THE CURE OF COMPOSITE MATERIALS Ana Yong 1, 2, Graham D. Sims 1,
More informationEnthalpy of Phase Change Materials as a Function of Temperature: Required Accuracy and Suitable Measurement Methods
Int J Thermophys (2009) 30:1257 1269 DOI 10.1007/s10765-009-0641-z Enthalpy of Phase Change Materials as a Function of Temperature: Required Accuracy and Suitable Measurement Methods Eva Günther Stefan
More informationThermal and UV-curing Behavior of Inks, Adhesives, and Coatings by Photo-, In-situ DEA and DMA.
Thermal and UV-curing Behavior of Inks, Adhesives, and Coatings by Photo-, In-situ DEA and DMA. Dr. Gilles Widawski, Netzsch Instruments North America, Burlington, MA, USA Dr. Stephan Knappe, NETZSCH-Gerätebau
More informationChanges of State. Substances in equilibrium change back and forth between states at equal speeds. Main Idea
Section 4 s Substances in equilibrium change back and forth between states at equal speeds. A liquid boils when it has absorbed enough energy to evaporate. Freezing occurs when a substance loses enough
More informationMeasuring the Reaction Kinetics of Polyester/PCA-501(HAA) Powder Coatings With Dielectric Analysis (DEA)
Measuring the Reaction Kinetics of Polyester/PCA-501(HAA) Powder Coatings With Dielectric Analysis (DEA) Dr. Georgi Beschiaschvili and Liselotte Tanner; and Manfred Wenzler, November 6, 2003 Figure 1a
More informationAPPLICATIONS OF THERMAL ANALYSIS IN POLYMER AND COMPOSITES CHARACTERIZATION. Wei Xie TA Instruments
APPLICATIONS OF THERMAL ANALYSIS IN POLYMER AND COMPOSITES CHARACTERIZATION Wei Xie TA Instruments Abstract Thermal Analysis is the generic name for a series of measurement techniques traditionally used
More informationThermal analysis of Li 2 O TeO 2 glass
Journal of Non-Crystalline Solids 271 (2000) 12±17 www.elsevier.com/locate/jnoncrysol Thermal analysis of Li 2 O TeO 2 glass I. Avramov a, *, G. Guinev a, A.C.M. Rodrigues b a Institute of Physical Chemistry,
More informationDETERMINATION OF THE DECOMPOSITION PRODUCTS OF CALCIUM OXALATE USING THERMAL GRAVIMETRY AND INFRARED SPECTROMETRY
DETERMINATION OF THE DECOMPOSITION PRODUCTS OF CALCIUM OXALATE USING THERMAL GRAVIMETRY AND INFRARED SPECTROMETRY Objective: The objectives of this experiment are: (1) to determine the stability of various
More informationWe ll cut through this one. :) CHOPPED-UP CHAPTER
We ll cut through this one. :) CHOPPED-UP CHAPTER ENERGY CHAPTER 10 WHAT DO YOU KNOW? What first comes to your mind when you hear the term energy? What do calories measure? List three sources of energy.
More informationThermal Analysis measurements
Thermal Analysis measurements R W McCallum Ames Laboratory And Materials Science and Engineering Phase vs Phase Field phase set of states of a macroscopic physical system that have relatively uniform chemical
More informationDISSOLUTION PROFILLING OF NIMESULIDE SOLID DISPERSIONS WITH POLYETHYLENE GLYCOL, TALC AND THEIR COMBINATIONS AS DISPERSION CARRIERS
International Journal of PharmTech Research CODEN (USA): IJPRIF ISSN : 0974-4304 Vol.2, No.1, pp 480-484, Jan-Mar 2010 DISSOLUTION PROFILLING OF NIMESULIDE SOLID DISPERSIONS WITH POLYETHYLENE GLYCOL, TALC
More informationMelting and solidi cation of Pb nanoparticles embedded in an Al matrix as studied by temperature-modulated di erential scanning calorimetry
PHILOSOPHICAL MAGAZINE LETTERS, 1998, VOL. 78, NO. 1, 37± 44 Melting and solidi cation of Pb nanoparticles embedded in an Al matrix as studied by temperature-modulated di erential scanning calorimetry
More informationApparent Melting: A New Approach to Detecting Drug-Excipient Incompatibility
Apparent Melting: A New Approach to Detecting Drug-Excipient Incompatibility Keywords: Melting Temperature, eat of Fusion, Apparent Melting, Thermodynamic Melting, Kinetic Process, Differential Scanning
More informationTHE PARTICLE MODEL AND PROPERTIES OF THE GASES, LIQUIDS AND SOLIDS. STATES CHANGES
THE PARTICLE MODEL AND PROPERTIES OF THE GASES, LIQUIDS AND SOLIDS. STATES CHANGES The particle model of a gas A gas has no fixed shape or volume, but always spreads out to fill any container. There are
More informationAnalyzing & Testing. Simultaneous Thermal Analysis. Method, Technique, Applications STA 449 F3. Leading Thermal Analysis
Analyzing & Testing Simultaneous Thermal Analysis Method, Technique, Applications STA 449 F3 Leading Thermal Analysis Method For 50 years, NETZSCH Analyzing & Testing has been a leading manufacturer of
More informationWhich particle diagram represents molecules of only one compound in the gaseous phase?
Name: 1) Which species represents a chemical compound? 9114-1 - Page 1 NaHCO3 NH4 + Na N2 2) 3) 4) Which substance represents a compound? Co(s) O2(g) CO(g) C(s) Which terms are used to identify pure substances?
More informationN E W S L E T T E R F R O M TO S H V I N A N A LY T I C A L P V T. LT D.
N E W S L E T T E R F R O M TO S H V I N A N A LY T I C A L P V T. LT D. AUGUST 204 TABLE OF CONTENTS Evaluation of Light Intensity Graph and Particle Size Distribution of Mixture Particle Application
More information25. Water Module. HSC 8 - Water November 19, Research Center, Pori / Petri Kobylin, Peter Björklund ORC-J 1 (13)
25. Water Module 14018-ORC-J 1 (13) Fig. 1. Pressure-Temperature calculator for water. The Pressure and Temperature calculator enables a complete thermodynamic description for a species, by allowing the
More informationChapter 4. The Physical transformations of pure substances Fall Semester Physical Chemistry 1 (CHM2201)
Chapter 4. The Physical transformations of pure substances 2011 Fall Semester Physical Chemistry 1 (CHM2201) Contents Phase Diagrams 4.1 The stabilities of phases 4.2 Phase boundaries 4.3 Three representative
More informationHow to Use Kinetic Modeling Analysis To Predict Profile Part Failure
Tips and Techniques Reprinted From: PLASTICS TECHNOLOGY Magazine How to Use Kinetic Modeling Analysis To Predict Profile Part Failure Real-world project demonstrates how kinetic modeling can help estimate
More informationHow to Run the Analysis: To run a principal components factor analysis, from the menus choose: Analyze Dimension Reduction Factor...
The principal components method of extraction begins by finding a linear combination of variables that accounts for as much variation in the original variables as possible. This method is most often used
More informationPOLYAMIDE-6,9 WITH CARBAZOLE
Chapter 5 POLYAMIDE-6,9 WITH CARBAZOLE CONTENTS 5.1 Introduction 174 5.2 Thermogravimetric Analysis 175 5.3 Differential Scanning Calorimetry 176 5.3.1 Pan Melt Blending 176 5.3.1.1 Melting Temperatures
More informationDSC Methods to Quantify Physical Aging and Mobility in Amorphous Systems: Assessing Molecular Mobility
DSC Methods to Quantify Physical Aging and Mobility in Amorphous Systems: Assessing Molecular Mobility R. B. Cassel, Ph.D. TA Instruments, 109 Lukens Drive, New Castle, DE 19720, USA ABSTRACT The specific
More informationHeat Transfer in Polymers
Heat Transfer in Polymers Angela Dawson, Martin Rides, Crispin Allen 18 April 2007 Heat Transfer in Polymers - Summary Introduction Heat Transfer Coefficients Standards for Thermal Properties Measurement
More informationDSC AS PROBLEM-SOLVING TOOL: BETTER INTERPRETATION OF Tg USING CYCLIC DSC
DSC AS PROBLEM-SOLVING TOOL: BETTER INTERPRETATION OF Tg USING CYCLIC DSC Problem A scientist is having difficulty in interpreting DSC results on a sample of polystyrene film. The sample exhibits a complex
More informationExperiment 14 It s Snow Big Deal
Experiment 14 It s Snow Big Deal OUTCOMES After completing this experiment, the student should be able to: use computer-based data acquisition techniques to measure temperatures. draw appropriate conclusions
More informationChapter 5 Energy and States of Matter. Changes of State. Melting and Freezing. Calculations Using Heat of Fusion
Chapter 5 Energy and States of Matter Changes of State 5.6 Melting and Freezing 5.7 Boiling and Condensation 1 2 Melting and Freezing A substance is melting while it changes from a solid to a liquid. A
More informationUNIT 11 DIFFERENTIAL THERMAL ANALYSIS, SCANNING CALORIMETRY AND THERMOMETRIC TITRATIONS
UNIT 11 DIFFERENTIAL THERMAL ANALYSIS, SCANNING CALORIMETRY AND THERMOMETRIC TITRATIONS Differential Thermal Structure 11.1 Introduction Objectives 11.2 Differential Thermal Analysis (DTA) Principle Characteristics
More informationTemperature Dependent Solubility of C 60. Speaker: Chun I Wang ( 王俊壹 ) & 11.03
Temperature Dependent Solubility of C 60 Speaker: Chun I Wang ( 王俊壹 ) 2014.08.11 & 11.03 Fullerene (C 60 ) 1965-1970: Predicted the existence of C 60 Fullerene (C 60 ) 1985: Successful synthesis High atomistic
More informationScale-up problems are often perceived as difficult. Here the reaction calorimetry has proven to be
APPLICATION OF REACTION CALORIMETRY FOR THE SOLUTION OF SCALE-UP PROBLEMS A paper from the RC User Forum Europe, Interlaken, 1995 Francis Stoessel, Ciba AG, Basel, Switzerland. Scale-up problems are often
More informationStates of matter Part 2
Physical Pharmacy Lecture 2 States of matter Part 2 Assistant Lecturer in Pharmaceutics Overview The Liquid State General properties Liquefaction of gases Vapor pressure of liquids Boiling point The Solid
More informationModelling the phase and crystallisation behaviour of fat mixtures
Modelling the phase and crystallisation behaviour of fat mixtures Jan Los & Elias Vlieg IMM Solid State Chemistry, Radboud University Nijmegen, The Netherlands Introduction Equilibrium Kinetics The full
More informationImpurity Content of a Semiconductor Crystal
Impurity Content of a Semiconductor Crystal Experiment F1/3 Contents Impurity Content of a Semiconductor Crystal... 2 1 Aims... 2 Background... 3 Doping... 3 Crystal Growth... 4 The 4-point probe... 6
More informationApplication of genetic algorithm in pyrolysis model parameter estimation. Anna Matala 60968U
Application of genetic algorithm in pyrolysis model parameter estimation Anna Matala 60968U 1 Contents 1 Introduction 3 2 Small scale experiments 3 3 Pyrolysis Modeling 7 4 Genetic Algorithm 7 4.1 Basic
More informationCalorimetric investigations. in multi-component salt systems
Calorimetric investigations in multi-component salt systems D. Sergeev 1, E. Yazhenskikh 1, N. Talukder 1, D. Kobertz 1, K. Hack 2, M. Müller 1 1 Forschungszentrum Jülich, IEK-2 2 - GTT-Technologies 1
More informationIgneous Rock Notes. Page #:
Page #: Igneous Rock Notes Magma and lava form very different types of igneous rocks. Igneous rocks form from molten rock, but where does molten rock come from? The temperature inside Earth with depth.
More informationGases and States of Matter: Unit 8
Gases and States of Matter: Unit 8 States of Matter There are three states (also called phases) of matter. The picture represents the same chemical substance, just in different states. There are three
More informationInvestigating the solid-state properties of drug-loaded mesoporous silica
Snapshots of Doctoral Research at University College Cork 2010 Investigating the solid-state properties of drug-loaded mesoporous silica Robert Ahern School of Pharmacy, UCC Introduction The drugs don
More informationCHEMISTRY - TRO 4E CH.6 - THERMOCHEMISTRY.
!! www.clutchprep.com CONCEPT: ENERGY CHANGES AND ENERGY CONSERVATION is the branch of physical science concerned with heat and its transformations to and from other forms of energy. is the branch of chemistry
More informationMultiple Choice Identify the letter of the choice that best completes the statement or answers the question.
Chem 102--Exam #2 Multiple Choice Identify the letter of the choice that best completes the statement or answers the question. 1. When water is measured in a plastic graduated cylinder, a reverse meniscus
More informationC80. Calvet Calorimeter From ambient to 300 C. A trademark of KEP Technologies group
C80 Calvet Calorimeter From ambient to 300 C A trademark of KEP Technologies group C80 SENSOR The C80 Calorimeter is one of the most powerful, yet flexible calorimeters available. The high precision Calvet
More informationCalorimetry and Hess s Law Prelab
Calorimetry and Hess s Law Prelab Name Total /10 1. What is the purpose of this experiment? 2. Make a graph (using some kind of graphing computer software) of temperature vs. time for the following data:
More informationUnit 1 Lesson 6 Changes of State. Copyright Houghton Mifflin Harcourt Publishing Company
The Fact of the Matter What happens when matter changes state? The three most familiar states of matter are solid, liquid, and gas. A change of state is the change of a substance from one physical form
More informationMECHATRONICS II LABORATORY Experiment #4: First-Order Dynamic Response Thermal Systems
MECHATRONICS II LABORATORY Experiment #4: First-Order Dynamic Response Thermal Systems The simplest dynamic system is a linear first order system. The time response of a first-order system is exponential.
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 22768 First edition 2006-07-15 Rubber, raw Determination of the glass transition temperature by differential scanning calorimetry (DSC) Caoutchouc brut Détermination de la température
More informationBeating the Heat - Fast Scanning Melts Silk Beta Sheet Crystals. Tufts University, Medford MA, 02155, USA
Supplementary Figures Beating the Heat - Fast Scanning Melts Silk Beta Sheet Crystals Peggy Cebe 1*, Xiao Hu 2, David L. Kaplan 2, 1 Department of Physics and Astronomy, and 2 Department of Biomedical
More informationEarth and Space Science. Semester 2 Review, Part 2
Earth and Space Science Semester 2 Review, Part 2 2015 Chemical Weathering -The process that breaks down rock through chemical changes. Examples that cause chemical weathering include the action of water
More informationThermochimica Acta 531 (2012) Contents lists available at SciVerse ScienceDirect. Thermochimica Acta
hermochimica Acta 531 (2012 6 11 Contents lists available at SciVerse ScienceDirect hermochimica Acta journa l h o me page: www.elsevier.com/locate/tca hermodynamic properties of potassium nitrate magnesium
More informationNews & Trends for Thermal Analysis
Vietnam, October 2016 VõĐình Vũ News & Trends for Thermal Analysis Pharma Applications and Theory TA-Techniques DSC, Flash DSC, HPDSC TGA TMA DMA Agenda Compatibility and Interactions - Eutectic Systems
More informationUniversal Standard Protocols for Temperature and Material Characterization Calibration with Pharmaceuticals by Thermal Analysis
Universal Standard Protocols for Temperature and Material Characterization Calibration with Pharmaceuticals by Thermal Analysis Abstract: Manik Pavan.Maheswaram, Dhruthiman.Mantheni, Shravan Thakur Singh,
More informationCHEMISTRY Topic #2: Thermochemistry and Electrochemistry What Makes Reactions Go? Fall 2018 Dr. Susan Findlay See Exercises in Topic 8
CHEMISTRY 2000 Topic #2: Thermochemistry and Electrochemistry What Makes Reactions Go? Fall 208 Dr. Susan Findlay See Exercises in Topic 8 Vapour Pressure of Pure Substances When you leave wet dishes on
More information6.2: Melting point determination of Succinic Acid:
6.1: Results: In the present study, an embedded system for determining the melting point of chemicals is developed. The measuring system has temperature sensitivity up to 0.07 C with good accuracy. The
More informationThermal Analysis. Short Courses POLYCHAR 25 Kuala Lumpur. Copyright 2017 by Jean-Marc Saiter
Thermal Analysis Pr. Dr. Jean Marc Saiter Onyx développement, Hameau du Bois Ricard, 76770 Malaunay - France SMS sciences et méthodes séparatives, Université de Normandie, 76821 Mont Saint Aignan Cedex,
More informationWhat Happens When Rheological Properties Change? Looking into Rheological Properties with Simultaneous Collection of Microscopic Images
ANNUAL TRANSACTIONS OF THE NORDIC RHEOLOGY SOCIETY, VOL. 15, 2007 What Happens When Rheological Properties Change? Looking into Rheological Properties with Simultaneous Collection of Microscopic Images
More informationIntroduction to the Scanning Tunneling Microscope
Introduction to the Scanning Tunneling Microscope A.C. Perrella M.J. Plisch Center for Nanoscale Systems Cornell University, Ithaca NY Measurement I. Theory of Operation The scanning tunneling microscope
More informationA kinetically controlled crystallization process for identifying new co-crystal forms: Fast evaporation of solvent from solutions to dryness
A kinetically controlled crystallization process for identifying new co-crystal forms: Fast evaporation of solvent from solutions to dryness Partha Pratim Bag, a Mohit Patni, ab C. Malla Reddy* a Department
More informationSection 7.1. Weathering. SES3a. Objectives
SES3a. Objectives Distinguish between mechanical and chemical weathering. Describe the different factors that affect mechanical and chemical weathering. Identify variables that affect the rate of weathering.
More informationTGA Thermal Gravimetric Analysis
TGA Thermal Gravimetric Analysis General Thermogravimetry is a technique in which the mass of the sample is monitored against time or temperature while the temperature of the sample, in a specified atmosphere,
More informationAnswer: The relation between kelvin scale and Celsius scale is TK =TC => TC=TK
Question The triple points of neon and carbon dioxide are 24.57 K and 216.55 K respectively. Express these temperatures on the Celsius and Fahrenheit scales. Answer: The relation between kelvin scale and
More informationPreparation And Characterization Of Simvastatin Nanosuspension By Homogenization Method
International Journal of PharmTech Research CODEN (USA): IJPRIF ISSN : 0974-4304 Vol.5, No.1, pp 193-197, Jan-Mar 2013 Preparation And Characterization Of Simvastatin Nanosuspension By Homogenization Method
More informationThe Next Generation Science Standards (NGSS)
The Next Generation Science Standards (NGSS) CHAPTER 2, LESSON 1 HEAT, TEMPERATURE, AND CONDUCTION MS-PS1-4. Develop a model that predicts and describes changes in particle motion, temperature, and state
More informationAspirin Lab By Maya Parks Partner: Ben Seufert 6/5/15, 6/8/15
Aspirin Lab By Maya Parks Partner: Ben Seufert 6/5/15, 6/8/15 Abstract: This lab was performed to synthesize acetyl salicylic acid or aspirin from a carboxylic acid and an alcohol. We had learned in class
More informationComparison of Different UV Light Sources in Radical Curing of PEGDA and PEGDA/HDDA Resins by Photo-DSC and Photo-DEA
Comparison of Different UV Light Sources in Radical Curing of PEGDA and PEGDA/HDDA Resins by Photo-DSC and Photo-DEA Dr. Pamela J. Shapiro NETZSCH Instruments North America, LLC Burlington, MA, USA Introduction
More informationAnalyzing & Testing. Thermogravimetric Analysis TGA. Technique, Instrument, Applications TG 209 F1. Leading Thermal Analysis
Analyzing & Testing Thermogravimetric Analysis TGA Technique, Instrument, Applications TG 209 F1 Leading Thermal Analysis Thermo-Microbalance TG 209 F1 Libra TGA Method Thermogravimetry (TG) or Thermogravimetric
More information- intermolecular forces forces that exist between molecules
Chapter 11: Intermolecular Forces, Liquids, and Solids - intermolecular forces forces that exist between molecules 11.1 A Molecular Comparison of Liquids and Solids - gases - average kinetic energy of
More informationDisdrometric data analysis and related microphysical processes
Author: Garcia Facultat de Física, Universitat de Barcelona, Diagonal 645, 08028 Barcelona, Spain. Advisor: Joan Bech Rustullet Abstract: The present paper consists in the analysis of Rain Drop Size Distribution
More informationName Student Activity
Open the TI-Nspire document Mechanical_Advantage.tns. In this activity, you will experiment with the incline plane and lever to discover the relationship between resistance and force. Then, you will derive
More informationA novel direct coupling of simultaneous thermal analysis (STA) and Fourier transform-infrared (FT-IR) spectroscopy
A novel direct coupling of simultaneous thermal analysis (STA) and Fourier transform-infrared (FT-IR) spectroscopy A. Schindler, G. Neumann, A. Rager, E. Füglein, J. Blumm & T. Denner Journal of Thermal
More informationCHEMISTRY: Chapter 10 Prep-Test
CHEMISTRY: Chapter 10 Prep-Test Matching Match each item with the correct statement below. a. calorimeter d. temperature b. calorie e. specific heat c. joule f. heat 1. quantity of heat needed to raise
More informationGlass transition and enthalpy relaxation of amorphous lactose glass
Carbohydrate Research 34 (26) 884 889 Glass transition and enthalpy relaxation of amorphous lactose glass Md. Kamrul Haque, a, * Kiyoshi Kawai b and Toru Suzuki a a Department of Food Science and Technology,
More informationLecture Presentation. Chapter 6. Thermochemistry. Sherril Soman Grand Valley State University Pearson Education, Inc.
Lecture Presentation Chapter 6 Thermochemistry Sherril Soman Grand Valley State University Chemical Hand Warmers Most hand warmers work by using the heat released from the slow oxidation of iron 4 Fe(s)
More informationENTROPY
ENTROPY 6.2.8 6.2.11 ENTHALPY VS. ENTROPY ENTROPY (S) the disorder of a system - solid liquid gas = entropy - gas liquid solid = entropy - mixing substances always = entropy SPONTANEOUS VS. NONSPONTANEOUS
More informationStabilizing vitamin D 3 by conformationally selective co-crystallization
Supporting Information for Stabilizing vitamin D 3 by conformationally selective co-crystallization Jian-Rong Wang, Chun Zhou, Xueping Yu and Xuefeng Mei* Pharmaceutical Analytical & Solid-State Chemistry
More information