Engineering Mechanics Laboratory Manual
|
|
- Myrtle Sullivan
- 5 years ago
- Views:
Transcription
1 Engineering Mechanics Laboratory Manual M.H.SABOO SIDDIK COLLEGE OF ENGG. Prof.Shaikh Ibrahim Ismail Automobile Engg. Dept. M.H.SABOO SIDDIK COLLEGE OF ENGG.
2 Engineering Mechanics 3 CONTENTS NO. EXPERIMENT 1 Polygon Law of Coplanar Forces To verify the polygon law of coplanar Forces for a concurrent force system. PAGE 5 2 Support Reactions of a beam To find experimentally the reactions at the supports of a simply supported beam and verify the same with analytical values. 8 3 Bell crank Lever To verify the principle of moments using the bell crank lever apparatus Friction Plane To determine the coefficient of static friction between two surfaces. 5 Moment of Inertia of Flywheel To find screw jack and determine the coefficient of friction between the threads of the screw Compound Pendulum To estimate the value of acceleration due to gravity using a compound pendulum. 31
3 4 Engineering Mechanics GENERAL INSTRUCTION FOR PREPARING MECHANICS PRACTICAL FILE The report of the experiments performed in the Mechanics Laboratory need to be written in a paper standard format. All such reports of various experiments performed would make the Mechanics Practical File. General instructions for writing a report on the experiments performed are listed below. Use one side ruled and the other side lank A-4 size Journal sheets. On the ruled side of the first sheet write in big font the Title (name) of the experiment. On the blank side of first sheet draw Apparatus diagram. On ruled side of second sheet write Aim Apparatus/Materials required Theory/Principle Procedure On the blank side of second sheet draw FBD and make observation table. On the ruled side of third sheet continue to write the procedure, show Calculations and present the results/conclusion. If required more sheets may be used. Use millimeter graph papers wherever required.
4 Engineering Mechanics 5 EXPERIMENT NO. 1 POLYGON LAW OF COPLANAR FORCES
5 6 Engineering Mechanics DIAGRAM: F 3 F 2 F 4 F 1 F 5 OBSERVATION TABLE: SR NO F1 (N) F2 (N) F3 (N) F4 (N) F5 (N) Θ (deg.) α (deg.) β (deg.) γ (deg.)
6 Engineering Mechanics 7 EXPERIMENT NO.1 DATE: GENERAL CO-PLANAR FORCE SYSTEM AIM: To verify the conditions of equilibrium for a general coplanar force system. APPARATUS: wooden board, pulleys with clamps, a sheet of paper, loads with hooks at one end and weights. THEORY: The conditions of equilibrium ΣFx = 0, ΣFy = 0 & ΣM=0. PROCEDURE: Pin a sheet of drawing paper on the board. Tie four threads/cords on the corners of a wooden plank and pass the cords over the pulleys, clamped in different positions on the board and suspend weights at the end of the cords. Adjust the weights until equilibrium of the system is established. Mark the lines of action of the forces on the paper and note down their magnitudes. Remove the paper. Draw the lines of actions of all the forces and verify ΣFx = 0, ΣFy = 0 Take any point on the paper. Draw perpendiculars from this point to the lines of actions of all forces and enter perpendicular distances in the observation table. Show that anti-clockwise moment is equal to clockwise moments, which satisfy the condition, that ΣM=0. Repeat the experiment for different weights to get 2 more readings. RESULT 1. The force polygons for the three sets of observations were drawn and found to be closed polygons. Hence the Polygon Law of Coplanar Force is verified. 2. The unknown weight found experimentally is N. Within limits of experimental error, these values are found to be same and hence the experiment is verified. Teacher s Signature
7 8 Engineering Mechanics EXPERIMENT NO. 2 SUPPORT REACTIONS OF A BEAM (BEAM APPARATUS)
8 Engineering Mechanics 9 OBSERVATION TABLE:- Sr. No W1 (Kg) W2 (Kg) X1 (Kg) X2 (Kg) Observed Reactions R1 (N) R2 (N) R1 (N) Analytical Reactions R2 (N)
9 10 Engineering Mechanics EXPERIMENT NO.2 BEAM REACTION DATE: AIM:-To find experimentally the reactions at the supports of a simply supported beam and compare the results with analytical values. APPARATUS:-Simply supported beam setup, hangers, and loads. THEORY:-Beam is a structural member usually horizontal and straight provided to carry loads that are vertical or inclined to its axis. A simply supported beam is one whose ends are resting freely on the supports that provide only vertical reactions. Simply supported beam becomes unstable if it is subjected to oblique or inclined loads. When simply supported beam is subjected to only vertical loads, its FBD forms a system of parallel forces in equilibrium. Conditions of equilibrium = 0 and ΣM=0 can be applied to determine the support reactions analytically. PROCEDURE:- 1. Place the beam of length L on simple supports. Not e that below both the simple supports there is a spring arrangement. On loading, 1 he spring compresses due to the reaction force and this compressive force is indicated on the dial. 2. Arrange the load hangers arbitrarily on the beam and set the left and right dial pointers to zero. This will nullify the effect due to self weight of the beam and the hangers. 3. Suspend the loads from the hangers. Note the load values W1 W2, and so on and their distances X1, X2 and so on from the left support. 4. Note the left and right support dial readings. 5. Repeat the above steps 1 to 4 by changing the weights in the hangers and also the hanger position for two more sets of observations. 6. Compare the experimental values with analytical values obtained by applying Conditions of Equilibrium
10 Engineering Mechanics 11 RESULT:- The support reactions obtained experimentally are nearly equal to the analytical values. The difference is within the limits of experimental error. Hence the experiment is verified. Teacher s Signature
11 12 Engineering Mechanics
12 Engineering Mechanics 13 EXPERIMENT NO.3 BELL CRANK LEVER
13 14 Engineering Mechanics
14 Engineering Mechanics 15 EXPERIMENT NO.3 DATE: BELL CRANK LEVER AIM:-To verify the Principle of Moments using the Bell Crank Lever apparatus. APPARATUS:- Bell crank lever apparatus, hangers, weights, scale. THEORY:-Principle of Moments states, the algebraic sum of the moments of a system of coplanar forces about any point in the plane is equal to the moment of the resultant force of the system about the same point. This principle would be verified for a bell crank lever arrangement. A lever whose two arms form a right angle, or nearly a right angle and having its fulcrum at the apex of the angle is referred to as a bell crank lever. These levers were originally used to operate the bell from a long distance especially where change in direction of bell wires was involved and hence the name. Now bell crank levers are used in machines to convert the direction of reciprocation movement. PROCEDURE:- 1. Arrange three hangers at arbitrary locations on the horizontal arm. Note the locations x1, x2, and x3 of these hangers from the hinge. Adjust the tension in the spring connected to the vertical arm such that the two pointers come in the same vertical line. In this position the horizontal arm is truly horizontal. Note the tensile force in the spring as the initial tension Ti. Also note the location Y of the spring from the hinge. 2. Hang the weights W1, W2 and W3 from the hangers. This will cause the arms to tilt and the pointers to move away from each other. Now adjust the tension in the spring such that the pointers once again come in the same vertical line. The horizontal arm is once again in its horizontal position. Note the tensile force in the spring as the final tension Tf. The tensile force T on the vertical arm is the difference Tf Ti. 3. Since the external forces are being supported by the single hinge at the apex of the arms, implies that the resultant of these external applied forces passes through the supporting hinge. Therefore to verify the principle of moments we need to take moments (ΣM) of all the external forces (which includes the weights of the hangers hanging from the horizontal arm and the tension in the spring connected to the vertical arm) about the hinge and if the total sum is zero, verifies the law of moments since the moment of the resultant is also zero at the hinge. 4. Repeat the above steps by changing the weights and their location on the horizontal arm for two more set of observations.
15 16 Engineering Mechanics FREE BODY DIAGRAM
16 Engineering Mechanics 17 PRECAUTIONS:- 1. Do not overload the horizontal arm as it may bend or crack at the hinge. 2. Note if any, the zero error of the spring balance and accordingly correct the readings. of the tensile force. 3. Carefully place the loads in the hangers as they may slip and cause accident. RESULT:- The sum of moments of all the applied external forces on the bell crank lever, within limits of experimental error being close to zero, is in accordance to the Principle of Moments. Hence the experiment is verified. Teacher s Signature
17 18 Engineering Mechanics
18 Engineering Mechanics 19 EXPERIMENT NO.4 FRICTION PLANE
19 20 Engineering Mechanics
20 Engineering Mechanics 21 EXPERIMENT NO.4 DATE: FRICTION AIM:-To find the Coefficient of Friction between two surfaces. APPARATUS:- Inclined Plane with pulley, weights,trolleys,weight pan etc. THEORY Friction force is developed whenever there is a motion or tendency of motion of one body with respect to the other body involving rubbing of the surfaces of contact. Friction is therefore a resistance force to sliding between two bodies produced at the common surfaces of contact. Friction occurs because no surface is perfectly smooth, however flat it may appear. On every surface there are microscopic hills and valleys and due to this the surfaces get interlocked making it difficult for one surface to slide over the other. During static state the friction force developed at the contact surface depends on the magnitude of the disturbing force. When the body is on the verge of motion the contact surface offers maximum frictional force called as Limiting Frictional Force. In 1781 the French Physicist Charles de Coulomb found that the limiting frictional force did not depend on the area of contact but depends on the materials involved and the pressure (normal reaction) between them. Thus frictional force F α N or F = μsn Here μs is the coefficient of static friction, a term introduced by Coulomb. The value of lies between 0 and 1 and it depends on both the surfaces of contact. Coefficient of static friction μs between two surfaces can be found out experimentally by two methods, viz. Angle of Repose method and Friction Plane method.
21 22 Engineering Mechanics OBSERVATION TABLE: Type of Surface Wood Weight in trolley (W) Angle of the Plane (Ѳ) Weight in pan (P) Coefficient of friction (μ) Average (μ) Angle of repose, φ Analytical Experimental Metal
22 Engineering Mechanics 23 The minimum angle of an inclined plane at which a body kept on it slides down the plane without the application of any external force is known as Angle of Repose. It is denoted by letter φ. Angle of repose, φ = tan -1 μs PROCEDURE 1. Set the inclined plane with glass top at some angle with the horizontal. Note the inclination θ of the plane on the quadrant scale. Take a box of known weight, note its bottom surface (whether surface is soft wood, or sand paper, or card board etc,) and weight W (weight of box + weights in the box) 2. Tie a string to the box and passing the string over a smooth pulley, attach an effort pan to it. 3. Slowly add weights in the effort pan. A stage would come when the effort pan just slides down pulling the box up the plane. Using fractional weights up to a least count of 5 gm, find the least possible weight in the pan that causes the box to just slide up the plane. Note the weight in the effort pan. This is force P. 4. Repeat the above steps 1 to 3 by changing the weights in the box for two more sets of observations. RESULT:- 1. The coefficient of friction between mica and wood is The coefficient of friction between mica and metal is Teacher s Signature
23 24 Engineering Mechanics
24 Engineering Mechanics 25 EXPERIMENT NO. 5 MOMENT OF INERTIA OF FLYWHEEL
25 26 Engineering Mechanics
26 Engineering Mechanics 27 EXPERIMENT NO.5 DATE: AIM To find moment of inertia of a flywheel. MOMENT OF INERTIA OF A FLYWHEEL APPARATUS The flywheel mounted on ball bearings, stop watch, set of weights, pan, string, meter scale. THEORY A flywheel; is a heavy metal wheel attached to the shaft of the prime mover (motor or engine). Flywheels have most of their mass concentrated on the circumstances, thereby giving high moment of inertia. We know rotating bodies possess kinetic energy given by the relation K.E = 1 /2 Iω 2. Hence if moment of inertia I is increased, K.E also increases. Flywheels thus store the kinetic energy and release it back to the system when required. They are therefore called as reservoir of energy. An imported application of a flywheel is in a mechanical press where for a fraction of time high energy is required for actual punching, shearing or forming. This energy is supplied by the flywheel. During the longer non active period, the speed of the flywheel is built up slowly by a low powered motor. Thus the motor is not overloaded and also results in energy saving. In automobiles, the flywheel is provided by the combustion in the cylinders and provides energy for the compression stroke in the pistons. PROCEDURE 1. Wind a string around the shaft of the flywheel. Attach a pan of known weight from the end of the string. Hold the pan i.e. does not allow the flywheel to rotate. 2. Measure the diameter of the axle with a Vernier caliper. 3. Add some weight in the pan and note the total mass m of the pan. Also note the height h of the base of the pan from the ground. 4. Hold a stop watch and now release the pan. The pan accelerates and gains velocity as it travels down. Note the time and rotations N1 turned by the flywheel till the pan touches the ground. 5. When the pan hits the ground it gets detached from the flywheel. The flywheel continues to rotate. Note the rotations N2 turned by the flywheel from the moment the pan touches the ground till the flywheel stops. 6. Repeat the above steps by changing the height of the pan from the ground and the moment weight in the pan for one more set of observations.
27 28 Engineering Mechanics OBSERVATION TABLE SR NO DESCRIPTION 1 st set 2 nd set 1 Radius of axle,r = m m 2 Height of fall, h = m m 3 Total mass of pan, m = kg kg 4 No. of rotations made by the flywheel till the pan touches the ground, N1 = Nos. Nos. 5 No. of rotations made from the moment the pan touches the ground till the flywheel stops, N2= Nos. Nos. 6 Time taken by the pan to touch the ground, t = sec sec 7 Moment of inertia of flywheel,i = kgm 2 kgm 2 Mean I =
28 Engineering Mechanics 29 CALCULATIONS Rectilinear motion of pan Taking s = height of fall h, u = 0 and t = time taken by pan to touch the ground. Use s = ut + 1 /2 at 2 and find acceleration of pan = m/s 2 Use v = u + at and find velocity of the pan as it strikes the ground. V = m/s Rotation motion of flywheel. USE ω = v/r and find angular velocity of the flywheel at the instant the pan to touches the ground. ω = r/s Use the formula to find moment of inertia I = 2mgh mr 2 ω 2 (1 + N1/N2) ω 2 (1 + N1/N2) RESULT: Mean moment of inertia of the flywheel is kgm 2 Teacher s Signature
29 30 Engineering Mechanics
30 Engineering Mechanics 31 EXPERIMENT NO.6 COMPOUND PENDULUM
31 32 Engineering Mechanics
32 Engineering Mechanics 33 EXPERIMENT NO. DATE: MOMENT OF INERTIA OF THE COMPOUND PENDULUM. AIM:-To find the moment of inertia of the compound pendulum. APPARATUS : A steel rod with holes in it for suspension (bar pendulum), A knife edged fulcrum, stop watch, meter scale. THEORY Compound pendulum is defined as a right body suspended in a vertical plane, from a point on the body other than centre of gravity. On giving small angular displacements, it oscillates and perform harmonic motion. We have Io=(t 2 mgb/4π) & IG=(IO-mb 2 )
33 34 Engineering Mechanics OBSERVATIONS:- Mass of uniform bar,m= kg No. of oscillations = 20 Length of the bar L = 1m ANALYTICALLY, IG = ml 2 /12 OBSERVATION TABLE: Sr.No. b (meter) T (sec.) t =T/20 (sec.) Io=(t 2 mgb/4π) IG=(IOmb 2 ) IG average
34 Engineering Mechanics 35 RESULT:- Moment of inertia of the compound pendulum (experimental) = Moment of inertia of the compound pendulum (analytical) = Teacher s Signature
35 36 Engineering Mechanics
36 Engineering Mechanics 37
Varuvan Vadivelan. Institute of Technology LAB MANUAL. : 2013 : B.E. MECHANICAL ENGINEERING : III Year / V Semester. Regulation Branch Year & Semester
Varuvan Vadivelan Institute of Technology Dharmapuri 636 703 LAB MANUAL Regulation Branch Year & Semester : 2013 : B.E. MECHANICAL ENGINEERING : III Year / V Semester ME 6511 - DYNAMICS LABORATORY GENERAL
More informationVALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR DEPARTMENT OF MECHANICAL ENGINEERING
VALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR 603203 DEPARTMENT OF MECHANICAL ENGINEERING BRANCH: MECHANICAL YEAR / SEMESTER: I / II UNIT 1 PART- A 1. State Newton's three laws of motion? 2.
More informationKNIFE EDGE FLAT ROLLER
EXPERIMENT N0. 1 To Determine jumping speed of cam Equipment: Cam Analysis Machine Aim: To determine jumping speed of Cam Formulae used: Upward inertial force = Wvω 2 /g Downward force = W + Ks For good
More informationApex Grammar School O & A Level Evening Classes. Physics EVALUATION TEST PAPER. REAL EXAMINATION QUESTIONS for Secondary 4
Apex Grammar School O & A Level Evening Classes O Level Power Revision Series EVALUATION TEST PAPER REAL EXAMINATION QUESTIONS for Secondary 4 Name: Time Start: Date: Time End: Total Marks : / 40 40 questions
More informationGeneral Physics 1. School of Science, University of Tehran Fall Exercises (set 07)
General Physics 1 School of Science, University of Tehran Fall 1396-97 Exercises (set 07) 1. In Fig., wheel A of radius r A 10cm is coupled by belt B to wheel C of radius r C 25 cm. The angular speed of
More informationUsing a Simple Pendulum plot L T and L T 2 graphs, hence find the effective length of second's pendulum using appropriate graph.
LABORATORY MANUAL LABORATORY MANUAL Using a Simple Pendulum plot L T and L T 2 graphs, hence find the effective length of second's pendulum using appropriate graph. Clamp stand; a split cork; a heavy metallic
More informationI B.TECH EXAMINATIONS, JUNE ENGINEERING MECHANICS (COMMON TO CE, ME, CHEM, MCT, MMT, AE, AME, MIE, MIM)
Code.No: 09A1BS05 R09 SET-1 I B.TECH EXAMINATIONS, JUNE - 2011 ENGINEERING MECHANICS (COMMON TO CE, ME, CHEM, MCT, MMT, AE, AME, MIE, MIM) Time: 3 hours Max. Marks: 75 Answer any FIVE questions All questions
More informationAnna University May/June 2013 Exams ME2151 Engineering Mechanics Important Questions.
Anna University May/June 2013 Exams ME2151 Engineering Mechanics Important Questions 1. Find the resultant force and its direction for the given figure 2. Two forces are acting at a point O as shown in
More information1 MR SAMPLE EXAM 3 FALL 2013
SAMPLE EXAM 3 FALL 013 1. A merry-go-round rotates from rest with an angular acceleration of 1.56 rad/s. How long does it take to rotate through the first rev? A) s B) 4 s C) 6 s D) 8 s E) 10 s. A wheel,
More informationInclined plane with protractor and pulley, roller, weight box, spring balance, spirit level, pan and thread.
To find the downward force, along an inclined plane, acting on a roller due to gravity and study its relationship with the angle of inclination by plotting graph between force and sin θ. Inclined plane
More informationKINGS COLLEGE OF ENGINEERING ENGINEERING MECHANICS QUESTION BANK UNIT I - PART-A
KINGS COLLEGE OF ENGINEERING ENGINEERING MECHANICS QUESTION BANK Sub. Code: CE1151 Sub. Name: Engg. Mechanics UNIT I - PART-A Sem / Year II / I 1.Distinguish the following system of forces with a suitable
More informationNCERT. To make a paper scale of given least count: (a) 0.2 cm and (b) 0.5 cm
ACTIVITIES 1 ACTIVITY AIM To make a paper scale of given least count: (a) 0.2 cm and (b) 0.5 cm APPARATUS AND MATERIAL REQUIRED Thick ivory/drawing sheet; white paper sheet; pencil; sharpener; eraser;
More informationis acting on a body of mass m = 3.0 kg and changes its velocity from an initial
PHYS 101 second major Exam Term 102 (Zero Version) Q1. A 15.0-kg block is pulled over a rough, horizontal surface by a constant force of 70.0 N acting at an angle of 20.0 above the horizontal. The block
More informationQ1. Which of the following is the correct combination of dimensions for energy?
Tuesday, June 15, 2010 Page: 1 Q1. Which of the following is the correct combination of dimensions for energy? A) ML 2 /T 2 B) LT 2 /M C) MLT D) M 2 L 3 T E) ML/T 2 Q2. Two cars are initially 150 kilometers
More informationRotational Dynamics Smart Pulley
Rotational Dynamics Smart Pulley The motion of the flywheel of a steam engine, an airplane propeller, and any rotating wheel are examples of a very important type of motion called rotational motion. If
More informationIt will be most difficult for the ant to adhere to the wheel as it revolves past which of the four points? A) I B) II C) III D) IV
AP Physics 1 Lesson 16 Homework Newton s First and Second Law of Rotational Motion Outcomes Define rotational inertia, torque, and center of gravity. State and explain Newton s first Law of Motion as it
More informationPhys 270 Final Exam. Figure 1: Question 1
Phys 270 Final Exam Time limit: 120 minutes Each question worths 10 points. Constants: g = 9.8m/s 2, G = 6.67 10 11 Nm 2 kg 2. 1. (a) Figure 1 shows an object with moment of inertia I and mass m oscillating
More informationCoefficient of Friction
HOUSTON COMMUNITY COLLEGE SYSTEMS SOUTHWEST COLLEGE COLLEGE PHYSICS I PHYS 1401 PRE LAB QUESTIONS Due before lab begins. Coefficient of Friction 1) Explain briefly the different types of frictional forces.
More informationSummer Physics 41 Pretest. Shorty Shorts (2 pts ea): Circle the best answer. Show work if a calculation is required.
Summer Physics 41 Pretest Name: Shorty Shorts (2 pts ea): Circle the best answer. Show work if a calculation is required. 1. An object hangs in equilibrium suspended by two identical ropes. Which rope
More informationRotation. PHYS 101 Previous Exam Problems CHAPTER
PHYS 101 Previous Exam Problems CHAPTER 10 Rotation Rotational kinematics Rotational inertia (moment of inertia) Kinetic energy Torque Newton s 2 nd law Work, power & energy conservation 1. Assume that
More information6. Find the net torque on the wheel in Figure about the axle through O if a = 10.0 cm and b = 25.0 cm.
1. During a certain period of time, the angular position of a swinging door is described by θ = 5.00 + 10.0t + 2.00t 2, where θ is in radians and t is in seconds. Determine the angular position, angular
More informationPhysics 4A Lab 11: MOMENT OF INERTIA Parts List
Part Quantity Rotating cross-arm table 1 Physics 4A Lab 11: MOMENT OF INERTIA Parts List Large iron disk 1 Large iron ring 1 50 grams hanger 1 Weights 1 set Table clamp 1 1-meter long rod 1 Pulleys 2 Rght-angle
More informationDept of ECE, SCMS Cochin
B B2B109 Pages: 3 Reg. No. Name: APJ ABDUL KALAM TECHNOLOGICAL UNIVERSITY SECOND SEMESTER B.TECH DEGREE EXAMINATION, MAY 2017 Course Code: BE 100 Course Name: ENGINEERING MECHANICS Max. Marks: 100 Duration:
More informationAP Physics Free Response Practice Oscillations
AP Physics Free Response Practice Oscillations 1975B7. A pendulum consists of a small object of mass m fastened to the end of an inextensible cord of length L. Initially, the pendulum is drawn aside through
More informationSt. Joseph s Anglo-Chinese School
Time allowed:.5 hours Take g = 0 ms - if necessary. St. Joseph s Anglo-Chinese School 008 009 First Term Examination Form 6 ASL Physics Section A (40%) Answer ALL questions in this section. Write your
More informationC7047. PART A Answer all questions, each carries 5 marks.
7047 Reg No.: Total Pages: 3 Name: Max. Marks: 100 PJ DUL KLM TEHNOLOGIL UNIVERSITY FIRST SEMESTER.TEH DEGREE EXMINTION, DEEMER 2017 ourse ode: E100 ourse Name: ENGINEERING MEHNIS PRT nswer all questions,
More information2. a) Explain the equilibrium of i) Concurrent force system, and ii) General force system.
Code No: R21031 R10 SET - 1 II B. Tech I Semester Supplementary Examinations Dec 2013 ENGINEERING MECHANICS (Com to ME, AE, AME, MM) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions
More informationName: Date: Period: AP Physics C Rotational Motion HO19
1.) A wheel turns with constant acceleration 0.450 rad/s 2. (9-9) Rotational Motion H19 How much time does it take to reach an angular velocity of 8.00 rad/s, starting from rest? Through how many revolutions
More informationb) 2/3 MR 2 c) 3/4MR 2 d) 2/5MR 2
Rotational Motion 1) The diameter of a flywheel increases by 1%. What will be percentage increase in moment of inertia about axis of symmetry a) 2% b) 4% c) 1% d) 0.5% 2) Two rings of the same radius and
More informationQuestions from all units
Questions from all units S.NO 1. 1 UNT NO QUESTON Explain the concept of force and its characteristics. BLOOMS LEVEL LEVEL 2. 2 Explain different types of force systems with examples. Determine the magnitude
More informationExperiment P28: Conservation of Linear and Angular Momentum (Smart Pulley)
PASCO scientific Physics Lab Manual: P28-1 Experiment P28: Conservation of Linear and Angular Momentum (Smart Pulley) Concept Time SW Interface Macintosh File Windows File rotational motion 45 m 500 or
More informationUNIT 4 FLYWHEEL 4.1 INTRODUCTION 4.2 DYNAMICALLY EQUIVALENT SYSTEM. Structure. Objectives. 4.1 Introduction
UNIT 4 FLYWHEEL Structure 4.1 Introduction Objectives 4. Dynamically Equivalent System 4.3 Turning Moment Diagram 4.3.1 Turning Moment Diagram of a Single Cylinder 4-storke IC Engine 4.3. Turning Moment
More informationRotation review packet. Name:
Rotation review packet. Name:. A pulley of mass m 1 =M and radius R is mounted on frictionless bearings about a fixed axis through O. A block of equal mass m =M, suspended by a cord wrapped around the
More informationAP practice ch 7-8 Multiple Choice
AP practice ch 7-8 Multiple Choice 1. A spool of thread has an average radius of 1.00 cm. If the spool contains 62.8 m of thread, how many turns of thread are on the spool? "Average radius" allows us to
More informationForce, Energy & Periodic Motion. Preparation for unit test
Force, Energy & Periodic Motion Preparation for unit test Summary of assessment standards (Unit assessment standard only) In the unit test you can expect to be asked at least one question on each sub-skill.
More informationCHAPTER 8 TEST REVIEW MARKSCHEME
AP PHYSICS Name: Period: Date: 50 Multiple Choice 45 Single Response 5 Multi-Response Free Response 3 Short Free Response 2 Long Free Response MULTIPLE CHOICE DEVIL PHYSICS BADDEST CLASS ON CAMPUS AP EXAM
More informationRolling, Torque & Angular Momentum
PHYS 101 Previous Exam Problems CHAPTER 11 Rolling, Torque & Angular Momentum Rolling motion Torque Angular momentum Conservation of angular momentum 1. A uniform hoop (ring) is rolling smoothly from the
More informationAP Physics. Harmonic Motion. Multiple Choice. Test E
AP Physics Harmonic Motion Multiple Choice Test E A 0.10-Kg block is attached to a spring, initially unstretched, of force constant k = 40 N m as shown below. The block is released from rest at t = 0 sec.
More information1. Replace the given system of forces acting on a body as shown in figure 1 by a single force and couple acting at the point A.
Code No: Z0321 / R07 Set No. 1 I B.Tech - Regular Examinations, June 2009 CLASSICAL MECHANICS ( Common to Mechanical Engineering, Chemical Engineering, Mechatronics, Production Engineering and Automobile
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission
2014. M32 Coimisiún na Scrúduithe Stáit State Examinations Commission LEAVING CERTIFICATE EXAMINATION, 2014 APPLIED MATHEMATICS HIGHER LEVEL FRIDAY, 20 JUNE MORNING, 9.30 to 12.00 Six questions to be answered.
More informationDYNAMICS MOMENT OF INERTIA
DYNAMICS MOMENT OF INERTIA S TO SELF ASSESSMENT EXERCISE No.1 1. A cylinder has a mass of 1 kg, outer radius of 0.05 m and radius of gyration 0.03 m. It is allowed to roll down an inclined plane until
More informationCEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5
1 / 36 CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5 Prof. Albert S. Kim Civil and Environmental Engineering, University of Hawaii at Manoa Date: 2 / 36 EQUATIONS OF MOTION: ROTATION
More informationCHAPTER 8: ROTATIONAL OF RIGID BODY PHYSICS. 1. Define Torque
7 1. Define Torque 2. State the conditions for equilibrium of rigid body (Hint: 2 conditions) 3. Define angular displacement 4. Define average angular velocity 5. Define instantaneous angular velocity
More informationForce and Motion 20 N. Force: Net Force on 2 kg mass = N. Net Force on 3 kg mass = = N. Motion: Mass Accel. of 2 kg mass = = kg m/s 2.
Force and Motion Team In previous labs, you used a motion sensor to measure the position, velocity, and acceleration of moving objects. You were not concerned about the mechanism that caused the object
More informationSIMPLE PENDULUM AND PROPERTIES OF SIMPLE HARMONIC MOTION
SIMPE PENDUUM AND PROPERTIES OF SIMPE HARMONIC MOTION Purpose a. To investigate the dependence of time period of a simple pendulum on the length of the pendulum and the acceleration of gravity. b. To study
More information31 ROTATIONAL KINEMATICS
31 ROTATIONAL KINEMATICS 1. Compare and contrast circular motion and rotation? Address the following Which involves an object and which involves a system? Does an object/system in circular motion have
More informationFigure Two. Then the two vector equations of equilibrium are equivalent to three scalar equations:
2004- v 10/16 2. The resultant external torque (the vector sum of all external torques) acting on the body must be zero about any origin. These conditions can be written as equations: F = 0 = 0 where the
More informationUse the following to answer question 1:
Use the following to answer question 1: On an amusement park ride, passengers are seated in a horizontal circle of radius 7.5 m. The seats begin from rest and are uniformly accelerated for 21 seconds to
More informationTHE SCREW GAUGE. AIM: To learn to use a Screw Gauge and hence use it to find the dimensions of various regular materials given.
EXPERIMENT NO: DATE: / / 0 THE SCREW GAUGE AIM: To learn to use a Screw Gauge and hence use it to find the dimensions of various regular materials given. APPARUTUS: Given a Screw Gauge, cylindrical glass
More informationRevolve, Rotate & Roll:
I. Warm-UP. Revolve, Rotate & Roll: Physics 203, Yaverbaum John Jay College of Criminal Justice, the CUNY Given g, the rate of free-fall acceleration near Earth s surface, and r, the radius of a VERTICAL
More informationPHYSICS 149: Lecture 21
PHYSICS 149: Lecture 21 Chapter 8: Torque and Angular Momentum 8.2 Torque 8.4 Equilibrium Revisited 8.8 Angular Momentum Lecture 21 Purdue University, Physics 149 1 Midterm Exam 2 Wednesday, April 6, 6:30
More informationS.3 PHYSICS HOLIDAY WORK Where necessary assume the acceleration due to gravity, g 10ms. 1. 7. 13. 19. 25. 2. 8. 14. 20. 26. 3. 9. 15. 21. 27. 4. 10. 16. 22. 28. 5. 11. 17. 23. 29. 6. 12. 18. 24. 30. SECTION
More information4.0 m s 2. 2 A submarine descends vertically at constant velocity. The three forces acting on the submarine are viscous drag, upthrust and weight.
1 1 wooden block of mass 0.60 kg is on a rough horizontal surface. force of 12 N is applied to the block and it accelerates at 4.0 m s 2. wooden block 4.0 m s 2 12 N hat is the magnitude of the frictional
More informationName Student ID Score Last First. I = 2mR 2 /5 around the sphere s center of mass?
NOTE: ignore air resistance in all Questions. In all Questions choose the answer that is the closest!! Question I. (15 pts) Rotation 1. (5 pts) A bowling ball that has an 11 cm radius and a 7.2 kg mass
More informationE X P E R I M E N T 11
E X P E R I M E N T 11 Conservation of Angular Momentum Produced by the Physics Staff at Collin College Copyright Collin College Physics Department. All Rights Reserved. University Physics, Exp 11: Conservation
More informationWebreview Torque and Rotation Practice Test
Please do not write on test. ID A Webreview - 8.2 Torque and Rotation Practice Test Multiple Choice Identify the choice that best completes the statement or answers the question. 1. A 0.30-m-radius automobile
More information1. An object is dropped from rest. Which of the five following graphs correctly represents its motion? The positive direction is taken to be downward.
Unless otherwise instructed, use g = 9.8 m/s 2 Rotational Inertia about an axis through com: Hoop about axis(radius=r, mass=m) : MR 2 Hoop about diameter (radius=r, mass=m): 1/2MR 2 Disk/solid cyllinder
More informationDr. Radhakrishnan A N Assistant Professor of Physics GPTC, Vechoochira
CONTENTS. Vernier Calipers. Screw Gauge. Simple Pendulum 7. Moment Bar 9. Convex Lens Appendix Vernier Calipers Exp. No: Date: Aim (i) To nd the volume of the given cylinder by measuring its length and
More informationLANMARK UNIVERSITY OMU-ARAN, KWARA STATE DEPARTMENT OF MECHANICAL ENGINEERING COURSE: MECHANICS OF MACHINE (MCE 322). LECTURER: ENGR.
LANMARK UNIVERSITY OMU-ARAN, KWARA STATE DEPARTMENT OF MECHANICAL ENGINEERING COURSE: MECHANICS OF MACHINE (MCE 322). LECTURER: ENGR. IBIKUNLE ROTIMI ADEDAYO SIMPLE HARMONIC MOTION. Introduction Consider
More informationTest 7 wersja angielska
Test 7 wersja angielska 7.1A One revolution is the same as: A) 1 rad B) 57 rad C) π/2 rad D) π rad E) 2π rad 7.2A. If a wheel turns with constant angular speed then: A) each point on its rim moves with
More informationTutorBreeze.com 7. ROTATIONAL MOTION. 3. If the angular velocity of a spinning body points out of the page, then describe how is the body spinning?
1. rpm is about rad/s. 7. ROTATIONAL MOTION 2. A wheel rotates with constant angular acceleration of π rad/s 2. During the time interval from t 1 to t 2, its angular displacement is π rad. At time t 2
More informationCode No: R Set No. 1
Code No: R05010302 Set No. 1 I B.Tech Supplimentary Examinations, February 2008 ENGINEERING MECHANICS ( Common to Mechanical Engineering, Mechatronics, Metallurgy & Material Technology, Production Engineering,
More informationAdvanced Higher Physics. Rotational motion
Wallace Hall Academy Physics Department Advanced Higher Physics Rotational motion Problems AH Physics: Rotational Motion 1 2013 Data Common Physical Quantities QUANTITY SYMBOL VALUE Gravitational acceleration
More information7.6 Journal Bearings
7.6 Journal Bearings 7.6 Journal Bearings Procedures and Strategies, page 1 of 2 Procedures and Strategies for Solving Problems Involving Frictional Forces on Journal Bearings For problems involving a
More informationStatics Chapter II Fall 2018 Exercises Corresponding to Sections 2.1, 2.2, and 2.3
Statics Chapter II Fall 2018 Exercises Corresponding to Sections 2.1, 2.2, and 2.3 2 3 Determine the magnitude of the resultant force FR = F1 + F2 and its direction, measured counterclockwise from the
More informationPHYSICS 221, FALL 2011 EXAM #2 SOLUTIONS WEDNESDAY, NOVEMBER 2, 2011
PHYSICS 1, FALL 011 EXAM SOLUTIONS WEDNESDAY, NOVEMBER, 011 Note: The unit vectors in the +x, +y, and +z directions of a right-handed Cartesian coordinate system are î, ĵ, and ˆk, respectively. In this
More informationTextbook Reference: Wilson, Buffa, Lou: Chapter 8 Glencoe Physics: Chapter 8
AP Physics Rotational Motion Introduction: Which moves with greater speed on a merry-go-round - a horse near the center or one near the outside? Your answer probably depends on whether you are considering
More informationExam 3 Practice Solutions
Exam 3 Practice Solutions Multiple Choice 1. A thin hoop, a solid disk, and a solid sphere, each with the same mass and radius, are at rest at the top of an inclined plane. If all three are released at
More informationTOPIC D: ROTATION EXAMPLES SPRING 2018
TOPIC D: ROTATION EXAMPLES SPRING 018 Q1. A car accelerates uniformly from rest to 80 km hr 1 in 6 s. The wheels have a radius of 30 cm. What is the angular acceleration of the wheels? Q. The University
More informationLecture 14. Rotational dynamics Torque. Give me a lever long enough and a fulcrum on which to place it, and I shall move the world.
Lecture 14 Rotational dynamics Torque Give me a lever long enough and a fulcrum on which to place it, and I shall move the world. Archimedes, 87 1 BC EXAM Tuesday March 6, 018 8:15 PM 9:45 PM Today s Topics:
More informationDYNAMICS ME HOMEWORK PROBLEM SETS
DYNAMICS ME 34010 HOMEWORK PROBLEM SETS Mahmoud M. Safadi 1, M.B. Rubin 2 1 safadi@technion.ac.il, 2 mbrubin@technion.ac.il Faculty of Mechanical Engineering Technion Israel Institute of Technology Spring
More informationFlywheels-Function need and Operation
STUDY OF FLYWHEEL Flywheel definition A flywheel is an inertial energy-storage device. It absorbs mechanical energy and serves as a reservoir, storing energy during the period when the supply of energy
More informationTEST REPORT. Question file: P Copyright:
Date: February-12-16 Time: 2:00:28 PM TEST REPORT Question file: P12-2006 Copyright: Test Date: 21/10/2010 Test Name: EquilibriumPractice Test Form: 0 Test Version: 0 Test Points: 138.00 Test File: EquilibriumPractice
More informationPHYSICS LAB Experiment 9 Fall 2004 THE TORSION PENDULUM
PHYSICS 83 - LAB Experiment 9 Fall 004 THE TORSION PENDULUM In this experiment we will study the torsion constants of three different rods, a brass rod, a thin steel rod and a thick steel rod. We will
More informationDEPARTMENT OF MECHANICAL ENGINEERING Dynamics of Machinery. Submitted
DEPARTMENT OF MECHANICAL ENGINEERING Dynamics of Machinery Submitted 1 UNIT I - Force Analysis INDEX (1) Introduction (2) Newton s Law (3) Types of force Analysis (4) Principle of Super Position (5) Free
More information1 The diagram shows an object of weight W and an object of weight Z balanced on a uniform metre rule. object of weight W. object of weight Z
1 The diagram shows an object of weight W and an object of weight Z balanced on a uniform metre rule. object of weight W a b 50 cm mark object of weight Z metre rule Which equation relating to W, Z, a
More informationPhysics 121, Final Exam Do not turn the pages of the exam until you are instructed to do so.
, Final Exam Do not turn the pages of the exam until you are instructed to do so. You are responsible for reading the following rules carefully before beginning. Exam rules: You may use only a writing
More informationPROBLEM 2 10 points. [ ] increases [ ] decreases [ ] stays the same. Briefly justify your answer:
PROBLEM 2 10 points A disk of mass m is tied to a block of mass 2m via a string that passes through a hole at the center of a rotating turntable. The disk rotates with the turntable at a distance R from
More informationME6511 DYNAMICS LABORATORY LIST OF EXPERIMENTS 1. Free Transverse Vibration I Determination of Natural Frequency 2. Cam Analysis Cam Profile and Jump-speed Characteristics 3. Free Transverse Vibration
More informationJNTU World. Subject Code: R13110/R13 '' '' '' ''' '
Set No - 1 I B. Tech I Semester Supplementary Examinations Sept. - 2014 ENGINEERING MECHANICS (Common to CE, ME, CSE, PCE, IT, Chem E, Aero E, AME, Min E, PE, Metal E) Time: 3 hours Max. Marks: 70 Question
More information2008 FXA THREE FORCES IN EQUILIBRIUM 1. Candidates should be able to : TRIANGLE OF FORCES RULE
THREE ORCES IN EQUILIBRIUM 1 Candidates should be able to : TRIANGLE O ORCES RULE Draw and use a triangle of forces to represent the equilibrium of three forces acting at a point in an object. State that
More informationPhysics EXERCISE- 1 (A)
EXERCISE- 1 (A) Question 1: What are contact forces? Give two Examples. Solution 1: The forces which act on bodies when they are in physical contact, are called contact forces. For e.g. frictional force
More informationUNIT 5 GOVERNORS 5.1 INTRODUCTION. Structure. 5.1 Introduction. 5.2 Classification of Governors 5.3 Gravity Controlled Centrifugal Governors
UNIT 5 GVERNRS Governors Structure 5. Introduction bjectives 5. lassification of Governors 5.3 Gravity ontrolled entrifugal Governors 5.3. Watt Governor 5.3. Porter Governor 5.4 Spring ontrolled entrifugal
More informationName Date Period PROBLEM SET: ROTATIONAL DYNAMICS
Accelerated Physics Rotational Dynamics Problem Set Page 1 of 5 Name Date Period PROBLEM SET: ROTATIONAL DYNAMICS Directions: Show all work on a separate piece of paper. Box your final answer. Don t forget
More informationMODEL PAPER CLASS XI PHYSICS (GROUP 1) BLUEPRINT Name of chapter (1)
sr. no. MODEL PAPER CLASS XI PHYSICS (GROUP ) BLUEPRINT Name of chapter VSAQ () SA-I (2) SA-II (3) Value based (4) LA(5) Total 70 Physical world and measurement 3 2 Kinematics 2 3,3 5 3 Laws of motion
More information11. (7 points: Choose up to 3 answers) What is the tension,!, in the string? a.! = 0.10 N b.! = 0.21 N c.! = 0.29 N d.! = N e.! = 0.
A harmonic wave propagates horizontally along a taut string of length! = 8.0 m and mass! = 0.23 kg. The vertical displacement of the string along its length is given by!!,! = 0.1!m cos 1.5!!! +!0.8!!,
More informationSample Final Exam 02 Physics 106 (Answers on last page)
Sample Final Exam 02 Physics 106 (Answers on last page) Name (Print): 4 Digit ID: Section: Instructions: 1. There are 30 multiple choice questions on the test. There is no penalty for guessing, so you
More informationSuggested Problems. Chapter 1
Suggested Problems Ch1: 49, 51, 86, 89, 93, 95, 96, 102. Ch2: 9, 18, 20, 44, 51, 74, 75, 93. Ch3: 4, 14, 46, 54, 56, 75, 91, 80, 82, 83. Ch4: 15, 59, 60, 62. Ch5: 14, 52, 54, 65, 67, 83, 87, 88, 91, 93,
More informationAPPLIED MATHEMATICS HIGHER LEVEL
L.42 PRE-LEAVING CERTIFICATE EXAMINATION, 203 APPLIED MATHEMATICS HIGHER LEVEL TIME : 2½ HOURS Six questions to be answered. All questions carry equal marks. A Formulae and Tables booklet may be used during
More informationSimple Harmonic Motion - MBL
Simple Harmonic Motion - MBL In this experiment you will use a pendulum to investigate different aspects of simple harmonic motion. You will first examine qualitatively the period of a pendulum, as well
More informationSECOND ENGINEER REG. III/2 APPLIED MECHANICS
SECOND ENGINEER REG. III/2 APPLIED MECHANICS LIST OF TOPICS Static s Friction Kinematics Dynamics Machines Strength of Materials Hydrostatics Hydrodynamics A STATICS 1 Solves problems involving forces
More informationBig Idea 4: Interactions between systems can result in changes in those systems. Essential Knowledge 4.D.1: Torque, angular velocity, angular
Unit 7: Rotational Motion (angular kinematics, dynamics, momentum & energy) Name: Big Idea 3: The interactions of an object with other objects can be described by forces. Essential Knowledge 3.F.1: Only
More informationEquilibrium of a Particle
ME 108 - Statics Equilibrium of a Particle Chapter 3 Applications For a spool of given weight, what are the forces in cables AB and AC? Applications For a given weight of the lights, what are the forces
More informationReview questions. Before the collision, 70 kg ball is stationary. Afterward, the 30 kg ball is stationary and 70 kg ball is moving to the right.
Review questions Before the collision, 70 kg ball is stationary. Afterward, the 30 kg ball is stationary and 70 kg ball is moving to the right. 30 kg 70 kg v (a) Is this collision elastic? (b) Find the
More informationName (please print): UW ID# score last first
Name (please print): UW ID# score last first Question I. (20 pts) Projectile motion A ball of mass 0.3 kg is thrown at an angle of 30 o above the horizontal. Ignore air resistance. It hits the ground 100
More informationName Date: Course number: MAKE SURE TA & TI STAMPS EVERY PAGE BEFORE YOU START. Grade: EXPERIMENT 4
Laboratory Section: Last Revised on June 18, 2018 Partners Names: Grade: EXPERIMENT 4 Moment of Inertia & Oscillations 0 Pre-Laboratory Work [20 pts] 1 a) In Section 31, describe briefly the steps you
More informationThe University of Melbourne Engineering Mechanics
The University of Melbourne 436-291 Engineering Mechanics Tutorial Eleven Instantaneous Centre and General Motion Part A (Introductory) 1. (Problem 5/93 from Meriam and Kraige - Dynamics) For the instant
More information2015 ENGINEERING MECHANICS
Set No - 1 I B. Tech I Semester Supplementary Examinations Aug. 2015 ENGINEERING MECHANICS (Common to CE, ME, CSE, PCE, IT, Chem E, Aero E, AME, Min E, PE, Metal E) Time: 3 hours Max. Marks: 70 Question
More informationDynamics of Machinery
Lab Manual Dynamics of Machinery (2161901) Name: Enrollment No.: Roll No.: Batch: Darshan Institute of Engineering & Technology, Rajkot DEPARTMENT OF MECHANICAL ENGINEERING Certificate This is to certify
More information