Robust MRAS Speed Observer and an Improved Zero-speed Position Estimation Design for Surface Permanent Magnet Synchronous Motor
|
|
- Britton Flynn
- 6 years ago
- Views:
Transcription
1 Robust MRAS Speed Observer and an Improved Zero-speed Position Estimation Design for Surface Permanent Magnet Synchronous Motor D. Zaltni and M. N. Abdelkrim National Engineering School of Gabes Research unit of Modelling, Analysis and Control Systems Rue Omar al Khattab, 69 Gabes TUNISIA zaltni Abstract: Model Reference Adaptive System (MRAS) based techniques are one of the best methods to estimate the rotor speed and position due to its performances and straight forward stability approach. In this paper, we propose a new robust MRAS scheme based on sliding mode techniques to the rotor speed of a Surface Permanent Magnet Synchronous Motor (SPMSM). Furthermore, an Estimator/Observer swapping system is designed to overcame position observability problems at zero speed which is an unobservable state point. The stability of the proposed observer is also discussed. Various tests are carried out in simulation to highlight the effectiveness and the robustness of the proposed rotor speed and position estimations design. Key Words: Permanent magnet synchronous motor, Model reference adaptive system, Observer, Sliding mode Introduction Permanent Magnet Synchronous Motor (PMSM) is an ideal candidate for high-performance industrial drives since it features simple structure, high-energy efficiency, reliable operation and high power density. In the conventional PMSM drive systems, speed and torque control are achieved by obtaining the rotor position or speed informations through shaft sensors such as optical encoders, Hall-Effect sensors or resolvers. The use of such sensors will increase the complexity, weight and cost of the system and reduce the overall reliability of the controlled drive system. Speed and position sensorless control of motor drive systems overcome above shortcomings and improve the overall system reliability, ruggedness and dynamic performance. Several methods are available for rotor speed estimation in a sensorless PMSM drive and they have been extensively studied in the last few decades [,, 3,, 5, 6, 7, 8]. The speed estimate is mandatory if speed control (feedback) is employed. Also the speed estimate is needed if decoupling is intended in the current regulation loops of the rotational reference frame. In a sensorless PMSM, the speed can be by various techniques. A speed estimate can be directly obtained using the machine s model equations. However, the accuracy is not very good. Other techniques are available: the Extended Kalman Filter method and the Luenberger observer construct full order estimators based on the machine model. Both approaches tend to depend heavily on the machine parameters and are generally difficult to implement. Compared with other methods, MRAS based techniques are one of the best methods to estimate the rotor speed due to its performance and straight forward stability approach. The MRAS system is wellknown in the sensorless control of Induction Motors and has been proved to be effective and physically clear [9,, ]. However, this techniques still sensible to some parameter variation [, 3]. To overcome this problem, Sliding Mode (SM) techniques can be introduced to the MRAS structure to ensure robustness and accuracy of the observer. In fact, SM techniques has attractive advantages of robustness to disturbances and insensitivity to parameter variations when the SM happens [, 5, 6]. However, the chattering behavior, that is inherent in standard sliding mode control, is often an obstacle for practical application if neglected. Higher Order Sliding Mode (HOSM) [7, 9,, ] is one of the solutions which does not compromise robustness. In this paper, a Second Order Sliding Mode (SOSM) observer is used as reference model in the proposed MRAS speed observer. This reference model is a speed-independent observer which computes the Back Electro- Motive Forces (BEMFs). The proposed model reference based on HOSM techniques is designed to ensure ISSN: ISBN:
2 the robustness of the observer and to reduce the chattering phenomenon. Therefore, the outputs signals of the reference model are smooth enough to be used directly as a reference BEMFs. A speed-dependent model is designed as adjustable model which computes BEMFs. Outputs of the reference and adjustable model are then fed into an adaptive sliding mode mechanism ensuring the convergence of the speed to the speed. The proposed MRAS observer is of high robustness and accuracy compared to other MRAS based techniques proposed in the literature [, 3]. The stability of the proposed observer is presented and discussed. The rotor position is obtained from the phase of the BEMFs. Since the position can not be calculated at very low frequencies, because the BEMFs are practically non existent, an Estimator/Observer swapping system is proposed to ensure rotor position estimation in all frequencies range. Tests are carried out at various operating conditions to illustrate the effectiveness and the high robustness of the proposed estimation design This paper is organized as follows: In section two, the mathematical model of the used PMSM is presented. In section three, a robust MRAS speed observer based SM techniques is proposed. Simulation results are illustrated in section four. Finally, some concluding remarks are given in the last section. T l is the load torque [i α i β ] T, [u α u β ] T are stator current and voltage vector respectively K e is the BEMF constant. θ e is the rotor position. 3 Robust MRAS Speed Observer The structure of the proposed MRAS speed observer is shown in Fig.. This structure is made up of a reference model, an adjustable model and an adaptation mechanism. In this structure the mechanical speed is considered slowly variable with respect to electrical dynamics. This assumption is a usual one for synchronous motor. Mathematical Model Of SPMSM The mathematical model of the used Surface Permanent Magnet Synchronous Motor in the (α-β) fixed coordinate is given by equation () and () [8, ]. ( ) i α = [( ) ( ) uα iα R i β L u β i β ω e K e ( sin(θe ) cos(θ e ) )] () ω e = P J φ m( sin(θ e )i α + cos(θ e )i β ) f v J ω e T l () J where ω e = Pω is the electric rotor speed ω is the rotor speed P is the pair pole number R is the stator resistance L is the stator inductance J is the moment of inertia φ m is the rotor flux f v is the viscous friction Figure : Structure of the MRAS Speed Observer based HOSM 3. The reference model The reference model consists in designing a second order sliding mode observer (Super Twisting Algorithm) which computes the reference BEMFs ê α,β = [ê α ê β ] T using only measured stator currents and voltages. This reference model does not depend on the velocity. The general form of the Super Twisting Algorithm is defined as follows [9]: u(e ) = u + λ e sgn(e ) u = α sgn(e ) (3) with e = x ˆx, λ, α > are the observer parameters, u is the output of the observer, x is the variable and: ISSN: ISBN:
3 if e > sgn(e ) = if e < [ ] if e = Let e α and e β be the BEMFs and x = [i α i β ]. Consider only current dynamic equations of the SPMSM, we can write: ẋ = ax be α + cu α ẋ = ax be β + cu β () with Let eα = ω e sin(θ e ) e β = ω e cos(θ e ) (5) [x a x b ] = b[e α e β ] (6) be the vector of unknown variables. Using (6), equation () becomes: ẋ = ax + x a + cu α ẋ = ax + x b + cu β (7) Currents and voltages are assumed to be measurable. Applying the STA (3) to system (7), we obtain systems (8) and (9): ˆx = x a + ax + cu α + λ e sgn(e ) (8) x a = α sgn(e ) Following the results proposed in [] and [] with respect to the super twisting algorithm (3) dedicated to the observer design given by equations (8) and (9), we set: Corollary: For any initial conditions x(), ˆx(), there exists a choice of λ i and α i such that the observer state ˆx converges in finite time to x, i.e. ˆx x and ˆx x then e, e, ė and ė converges to zero and by consequence x a x a and x b x b. Proof : Consider system (). To show the convergence of (ˆx, x a ) to (x, x a ) (ie., (e, e a ) (,)) let consider the system s dynamic ë ë = f (x b ) α sign(e ) λ e ė () with d x dt = ẋsign(x) Equation () leads to ë where [ ] f +, f+ α sign(e ) λ e ė (3) f + = max(f (x b )), ˆx = x b + ax + cu β + λ e sgn(e ) x b = α sgn(e ) (9) Where e = x ˆx, e = x ˆx and λ, λ, α, α are positive constants that will be given later. x a and x b are the values of the unknown variables x a and x b. According to equations (7), (8) and (9), error dynamics of the observer are given by: ė = e a λ e sgn(e ) () ė a = f (x b ) α sgn(e ) ė = e b λ e sgn(e ) ė b = f (x a ) α sgn(e ) () With e a = x a x a, e b = x b x b, f (x b ) = ω e x b and f (x a ) = ω e x a Figure : Finite time convergence behavior of the proposed observer : The majoring curve for the finite time convergence. ISSN: ISBN:
4 Figures and 3 illustrate the finite time convergence behavior of the reference model. In what follows we will give the error trajectory for each quadrant in the worst cases. de/dt e Figure 3: The trajectory ė = f(e ): Finite time convergence. First quadrant: e > and ė > Starting from point A of Fig. the trajectory of ė = f(e ) is in the first quadrant e and ė. The rising trajectory is given by ë = (α f + ) By choosing α > f + we ensure that ë < and hence ė decreases and tends towards the y-axis, corresponding to ė = (point B in Fig. ). Let e () be the intersection of this trajectory with ė = ; thus e () = (α f + )ė () () Then the rising trajectory for e > and ė > can be given by the following expression: ė = (α f + )(e () e ) (5) Second quadrant: e > and ė < In this case, ë = f + α sign(e ) λ e ė becomes negative (ë < ) on making a good choice of α which leads to (α + f + ) > λ e ė So, the rising trajectories as illustrated in Fig. are given as e = e () with ė λ (α + f + )e/ and ė = ė () = λ (α + f + )e/ () with ė > λ (α + f + )e/ (where ė () corresponds to the intersection of ė = λ (α + f + )e/ and e = e () (denoted by point C in Fig. )). Hence, if ė () ė () < which means that λ > (α + f + ), we can state that α f + α > f + and λ > (f + + α ) α f + (6) are sufficient conditions guaranteeing the state convergence (i.e. the states (e, ė ) tend towards e = ė = and in consequence the full convergence of ė (i) ). i= Now we will consider the system (). Following the same procedure, we can state that α > f + and λ > (f + + α ) α f + (7) are sufficient conditions guaranteeing the state convergence (i.e. the states (e, ė ) tend towards e = ė = and in consequence the full convergence of ė (i) ). i= Where f + = max(f (x a )), Now, in order to prove the finite time convergence, it is necessary to know the time passed in following the trajectory in each quadrant. In the first quadrant, the rising trajectory is given by ë = (α f + ). So, by integration, we can find that ė = (α f + )t+cte with cte = ė (). Hence the necessary time for going from A to B is t () = (α f + )ė() (8) In the second quadrant, we can find the rising trajectory leading to a much longer time. This is given by ë = f + α λ e ė. Then, as previously, we can write that ė = ( α f + )t λ e / + cte with cte = λ e / () because at B we have t = and ė =. Now in C we have ė () = ( α f + )t () + λ e / () ; then the necessary time for going from B to C is t () = ė ()+λ e / () which can be expressed as a function of ė () α +f + as: t () = (α + f + ) + λ λ (α + f + ) (α f + ) ė () (9) Following the same procedure and using the property of symmetry of the first and the third quadrant, we can find the time for going from C to D which can be given by t () = (α f + )ė(), and expressed also as function of ė () as t () = λ (α f + ) ė () () ISSN: ISBN:
5 and for the second and fourth quadrants, the time for going from D to E is t (3) = ė()+λ e () / ; since ė () = (α f + ) λ α +f + λ α f + α +f + α f + ė (), one easily obtains t (3) = (α f + ) + λ λ (α f + ) α f + ė () and e () / = α + f + α f + ė () () Let T d () be the necessary time interval for going from A to E; then T d () = t () + t () + t () + t (3) = Kė () () where K = + (α f + ) + (α + f + ) + λ (3) λ (α + f + ) (α f + ) + ) + λ + (α f λ (α f + ) λ (α f + ) α + f + α f + where ˆω e is the velocity (the output of the MRAS observer (show fig. )) and ( ) J = (6) For convergence, a feedback loop is introduced and the feedback gain is: ( ) G = g (7) where g is a positive constant. 3.3 The adaptation mecanism If the velocity estimation error exist, it will lead to the BEMFs estimation error : ε = ê α,β ẽ α,β (8) Then, this error together with the estimation model s output ẽ α,β is used to construct the manifold S as : and thus the convergence time for this step can be, in the worst case, given as T = T d (i) = Kė () + KWė () + KW ė () i= + KW 3 ė () +... () which gives With W = (α f + ) λ T = W Kė () α +f + α f + < and where λ is given by (6), and by consequence, we can finally conclude on the finite time convergence of (ˆx, x a ) towards (x, x a ). The same procedure is followed to demonstrate the finite time convergence of (ˆx, x b ) towards (x, x b ). Having x a and x b we can easily deduce the BEMFs ê α,β using (6). 3. The adjustable model The adjustable model is tunable by the velocity and it computes the BEMFs ẽ α,β = [ẽ α ẽ β ] T from the following equation: ẽ α,β = ˆω e Jẽ α,β + G(ẽ α,β ê α,β ) (5) The velocity is : S = ε T Jẽ α,β (9) ˆω e = Msgn(S) (3) Note that the speed estimate is a discontinuous function of the manifold and M is a positive constant. The BEMFs ê α,β computed by the reference model will converge in finite time T to e α,β. After this time (t > T ), the BEMFs used in the reference model are also satisfied the following equation: ê α,β = ω e Jê α,β (3) To show that the sliding mode can be enforced in the manifold S =, we need to show that there exist M sufficiently high such that the manifold is attractive: SṠ < (3) After differentiating (9) and replacing the derivative of the BEMFs from (5) and (3), the following expression is obtained: Ṡ = f(ω e, ê α,β, ẽ α,β ) M(ẽ T α,βê α,β )sgn(s) (33) where f is a function of the reference and BEMFs and speed. Since this term is greater than zero when the motor is exited and f has a positive upper value, it s clear from (33) that sufficiently high M can ISSN: ISBN:
6 be selected such that condition (3) is fulfilled. Thus, sliding mode is enforced in the manifold S and after sliding mode begins, we have S =. The boundary layer method described in [] is used to find the equivalent control ω e,eq. Once sliding mode occurs, we can also assume Ṡ = along with S =. The expression of the equivalent control becomes: ω e,eq [ẽ T α,βê α,β ] = ω e [ẽ T α,βê α,β ] + gε T Jẽ α,β (3) From (3) when the manifold converge to zero (S = ε T Jẽ α,β = ), the equivalent speed tends to the speed. The equivalent speed represents the lowfrequency component of the discontinuous term (3). Thus, while the high-frequency switching function is fed into the observer, it s low-frequency component can be obtained by Low-Pass Filtering (LPF) and represents the speed estimate. Simulation Results The used motor in the simulation testing is a threephase SPMSM. The specifications and parameters are listed in Table. Parameters of the MRAS observer are α =.5, α =.8, λ =.6, λ =., g = and M = 5. The observer is tested in open loop. Using current and voltage signals, the BEMFs are using the proposed SOSM BEMFs observer which is used as the reference model of the MRAS speed estimator. This observer does not depend on the speed. The adjustable model is tunable by the speed and it is implemented using equation (5) ( the output of the MRAS observer (ˆω e ) is used as a feedback to adjust the adjustable model as shown in Fig. ). The rotor position is obtained simply from the phase of the BEMFs as follows: ˆθ e = arctan( ê α ê β ) (35) However, it is shown in [] that the PMSM is not observable at zero speed. To overcome this problem, un Estimator/Observer swapping system is proposed to ensure position estimation in all speed range and to overcome position observability problems at very low frequencies. The estimator is obtained by integrating the speed as: ˆθ e = t ˆω e dt + cte (36) The initial value of the position (ˆθ e () = cte) is equal to the last value computed by the observer (35) before swapping to the estimator. Thus, since the speed is always observable, there is no problem of observability using this position estimator. The position is equal to the observer (35) when the motor operate at high frequencies and swap to the estimator (36) since the speed becomes less than a defined very low value. Reference rotor speed (rad/s) Load torque(n.m) Figure : Benchmark trajectories: Reference rotor speed (rad/s), Load torque (N.m) speed (rad/s) rotor position (rad) Figure 5: Nominal Case: rotor speed (rad/s), rotor position (rad) Dedicated Benchmark. The proposed observer is tested to the benchmark trajectories [3] presented in Fig.. In this benchmark, two reference trajectories are defined: The reference rotor speed (Fig. ) and the load torque (Fig. ). Initially, the motor is started to run from zero and increase to rad/s and still constant until t=.5s. The load torque is applied at t=.5s and removed at t=s. This first phase permit to test and evaluate the performance and the ISSN: ISBN:
7 robustness of the observer at low frequencies with application of the load torque. At t=.5s, the motor is accelerated until high frequency (57 rad/s). Then, the load torque is applied again at t=3s. This second phase permit to test the robustness of the observer at high frequency operating conditions. After that, the motor is decelerated to rad/s and still constant (zero speed and acceleration) until t=6s. This last phase permit to show the loss of observability at zero speed and acceleration. Finally, the motor is controlled out of the unobservable conditions. So the motor is tested at nominal case (Fig. 5 and 6). Robustness to internal disturbances is then tested by variation of +5% of stator resistance (Fig. 7), +5% of stator inductance (Fig. 8) and +5% of rotor flux (Fig. 9). Speed Estimation. From these tests, we remark that the estimate speed mach the one with very small steady-state error and good dynamics. The proposed observer is of high accuracy and robustness against internal disturbances (parameter variations) and external disturbances (load torque). Nevertheless an error occurs at fast changed speed time (for example in Fig. 5 at t=.6 s) because in this case the speed is not slowly variable compared to the electrical dynamic. Obviously this behavior is not a physically one. It is done only to show the limit performances of the proposed control. speed (rad/s) rotor position (rad) Figure 6: Estimator/Observer Swapping: Nominal Case: rotor speed (rad/s), rotor position (rad) Rotor position Estimation. For rotor position estimation, two tests are carried out. In the first test, we use only the observer ( Fig. 5). Fig. 5 shows the position which reach the one with good accuracy and robustness. However, at zero speed and acceleration, the rotor position is not observable. In the second test, we use the Estimator/Observer swapping system (Fig. 6, Fig. 7 Fig. 8 and Fig. 9). Thus, speed (rad/s) rotor position (rad) Figure 7: Estimator/Observer Swapping: +5% variation of stator resistance: rotor speed (rad/s), rotor position (rad) in these figures, we show that the rotor position can be obtained at all range of frequencies. However, in the unobservable region, we remark in Fig. 6 that the position is sensitive only to stator resistance variation. This is due to the use of the estimator in this range and not the observer. speed(rad/s) rotor speed(rad) Figure 8: Estimator/Observer Swapping: +5% variation of stator inductance: rotor speed (rad/s), rotor position (rad) 5 Conclusion In this paper, a new robust MRAS scheme based HOSM techniques is proposed for high accuracy and ISSN: ISBN:
8 speed (rad/s) rotor position (rad) Figure 9: Estimator/Observer Swapping: +5% variation of rotor flux: rotor speed (rad/s), rotor position (rad) robustness rotor speed estimation of a SPMSM. The stability of the proposed MRAS system has been studied and discussed. High performance estimation of the rotor position has been obtained using an Estimator/Observer swapping system and permit to overcome the problem of observability at low speed. Selected simulation results has been presented to illustrate the performance and the robustness of the proposed speed and position estimations design. Acknowledgements: The authors thank Doctor Malek GHANES and Professor Jean Pierre BARBOT for their helpful insight and support.. References: [] A. Consoli, S. Musumeci, A. Ractiti and A. Testa, Sensorless Vector and Speed Control of Brushless Motor Drives, IEEE Trans. Ind. Elect., Vol., 99, pp [] C. French and P. Acarnley, Control of Permanent Motor Drives using New Position Estimation Technique, IEEE Trans. Ind. Appl., Vol. 3, 996, pp [3] O. Ostlund and M. Brokemper, Sensorless Rotor Position Detection from Zero to Rated Speed for an Integrated PM Synchronous Motor Drive, IEEE Trans. Ind. Appl., Vol. 3, 996, pp [] J. H. Jang, S. K. Sul, J. I. Ha, et al, Sensorless Drive of Surface-Mounted Permanent Magnet Motor by High Frequency Signal Injection based on Magnetic Saliency, IEEE Trans. Industry Appl., Vol. 39, No., 3, pp [5] H. R. Lie, J. H. Wang, S. S. Gu, et al, A Neural- Network-based Adaptative Estimator of Rotor Position and Speed for Permanant Magnet Synchronous Motor, Proc. IEEE ICEMS., Vol.,, pp [6] J. Solsona, M. I. Valla and C. Muravchik, A Non linear Reduced Order Observer for Permanent Magnet Synchronous Motors, IEEE trans. Ind. Electr., Vol. 3, No., 996, pp [7] S. Bolognani, L. Tubiana and M. Zigliotto, Extented Kalman Filter tuning in Sensorless PMSM Drives, IEEE trans. Ind. Appl., Vol. 39, No. 6, 3, pp [8] K. Y. Lian, C. H. Chiang, and H. W. Tu, LMIbased Sensorless Control of Permanent Magnet Synchronous Motors, IEEE trans. Ind. Elect., Vol. 5, No. 5, 7, pp [9] C. Schauder, Adaptative Speed Identification for Vector Control of Induction Motors without Rotational Transducers, IEEE trans. Ind. Appl., Vol. 8, No. 5, 99, pp [] S. Maiti, C. Chakraborty, Y. Hori and M. C. Ta, Model Reference Adaptative Controller-Based Rotor Resistance and Speed Estimation Techniques for Vector Controlled Induction Motor Drive Utilizing Reactive Power, IEEE trans. Ind. Elect., Vol. 55, No., 8, pp [] C. M. Ta, T. Uchida and Y. Hori, MRAS-based Speed Sensorless Control for Indution Motor Drives using Instantaneous Reactive Power, Proc. 7 th IEEE Conf. on Ind. Elect. Soc.,, pp. 7-. [] Y. S. Kim, S. K. Kim and Y. A. Kwon, MRAS based Sensorless Control of Permanent Magnet Synchronous Motor, SICE Annual Conf., Fukui, August -6, 3, pp [3] M. M. Kojabadi and C. Liuchen, Sensorless PMSM drive with MRAS-based adaptive speed estimator, Proc. 37th IEEE Spec. conf. on Pow. Elect., 8- June 6, Jeju, 6, pp. -5. [] V. Utkin, J. Guldner and J. Shi, Sliding mode control in electromechanical systems, London: st Edition, Taylor et Francis, 999. [5] L. Sbita, D. Zaltni and M. N. Abdelkrim, Adaptative Variable Structure Control for an Online ISSN: ISBN:
9 Tuning Direct Vector Controlled induction motor drive, Int. J. Appl. Sienc. Vol. 7, No.,, 7, pp [6] M. Ghanes and G. Zheng, On Sensorless Induction Motor Drives: Sliding-Mode Observer and Output Feedback Controller IEEE Transactions on Industrial Electronics (TIE), Vol.56, N9, p. 3-33, September 9. [7] G. Bartolini, A. Ferrara and E. Usani, Chattering Avoidance by Second-Order Sliding Mode Control, IEEE trans. Autom. Cont., Vol. 3, No., 998, pp. -6. Table : PMSM characteristics Rated Power P n.7kw Rated speed ω n 57rad.s Rated voltage U n 38V Rated current I n 3.8A Number of pole pairs P 3 Stator inductance L.7H Stator resistance R 3.3 Ω Rotor flux φ m.3 Rotor inertia J.6kg.m Viscous friction f v.3kg.m.s [8] Z. Chen, M. Tomita, S. Doki and S. Okuma, An Extended Electromotive Force Model for Sensorless Control of Interior Permanent-Magnet Synchronous Motors, IEEE trans. Ind. Elect., Vol. 5, No., 3, pp [9] L. Fridman, A. Levant, Sliding modes of higher order as a natural phenomenon in control theory. In Robust control via variable structure and Lyapunov techniques, Lecture notes in control and information Science 7. F. Garofalo, L. Glielmo Ed. Springer Verlag London, 996, pp [] A. Levant, Robust exact differentiation via sliding mode technique, Automatica, Vol. 3, No. 3, 998, pp [] W. Perruquetti, J. P. Barbot, Sliding mode Control in engineering, New York: Marcel Dekker,. [] D. Zaltni, M.N. Abdelkrim, M. Ghanes and J.P. Barbot, Observability Analysis of PMSM, In proc. of IEEE Int. Conf. Signal Circuit and System, 6-8 nov. 9, Djerba, Tunisie, pp. -6. [3] A. Glumineau, R. Boiliveau (IRCcyN), L. Loron (IREENA), 8. ISSN: ISBN:
Synchronous Motor Observability Study and a New Robust MRAS Speed Observer with an Improved Zero-speed Position Estimation Design for Surface PMSM
Synchronous Motor Observability Study and a New Robust MRAS Speed Observer with an Improved Zero-speed Position Estimation Design for Surface PMSM DALILA ZALTNI, and MOHAMED NACEUR ABDELKRIM Ecole Nationale
More informationII. Mathematical Modeling of
SICE Annual Conference in Fukui, August 4-62003 Fukui University, Japan MRAS Based Sensorless Control of Permanent Magnet Synchronous Motor Young Sam Kim, Sang Kyoon Kim and Young Ahn Kwon Department of
More informationRobust Speed Controller Design for Permanent Magnet Synchronous Motor Drives Based on Sliding Mode Control
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 88 (2016 ) 867 873 CUE2015-Applied Energy Symposium and Summit 2015: ow carbon cities and urban energy systems Robust Speed Controller
More informationA New Model Reference Adaptive Formulation to Estimate Stator Resistance in Field Oriented Induction Motor Drive
A New Model Reference Adaptive Formulation to Estimate Stator Resistance in Field Oriented Induction Motor Drive Saptarshi Basak 1, Chandan Chakraborty 1, Senior Member IEEE and Yoichi Hori 2, Fellow IEEE
More informationSensorless Torque and Speed Control of Traction Permanent Magnet Synchronous Motor for Railway Applications based on Model Reference Adaptive System
5 th SASTech 211, Khavaran Higher-education Institute, Mashhad, Iran. May 12-14. 1 Sensorless Torue and Speed Control of Traction Permanent Magnet Synchronous Motor for Railway Applications based on Model
More informationBackstepping Control of Speed Sensorless Permanent Magnet Synchronous Motor Based on Slide Model Observer
International Journal of Automation and Computing 1(), April 015, 149-155 DOI: 10.1007/s11633-015-0881- Backstepping Control of Speed Sensorless Permanent Magnet Synchronous Motor Based on Slide Model
More informationSpeed Sensor less Control and Estimation Based on Mars for Pmsm under Sudden Load Change
International Journal of Engineering Inventions e-issn: 2278-7461, p-isbn: 2319-6491 Volume 2, Issue 3 (February 2013) PP: 77-86 Speed Sensor less Control and Estimation Based on Mars for Pmsm under Sudden
More informationMathematical Modeling and Dynamic Simulation of a Class of Drive Systems with Permanent Magnet Synchronous Motors
Applied and Computational Mechanics 3 (2009) 331 338 Mathematical Modeling and Dynamic Simulation of a Class of Drive Systems with Permanent Magnet Synchronous Motors M. Mikhov a, a Faculty of Automatics,
More informationSensorless Speed Control for PMSM Based On the DTC Method with Adaptive System R. Balachandar 1, S. Vinoth kumar 2, C. Vignesh 3
Sensorless Speed Control for PMSM Based On the DTC Method with Adaptive System R. Balachandar 1, S. Vinoth kumar 2, C. Vignesh 3 P.G Scholar, Sri Subramanya College of Engg & Tech, Palani, Tamilnadu, India
More informationSensorless Control for High-Speed BLDC Motors With Low Inductance and Nonideal Back EMF
Sensorless Control for High-Speed BLDC Motors With Low Inductance and Nonideal Back EMF P.Suganya Assistant Professor, Department of EEE, Bharathiyar Institute of Engineering for Women Salem (DT). Abstract
More informationAn adaptive sliding mode control scheme for induction motor drives
An adaptive sliding mode control scheme for induction motor drives Oscar Barambones, Patxi Alkorta, Aitor J. Garrido, I. Garrido and F.J. Maseda ABSTRACT An adaptive sliding-mode control system, which
More informationLecture 8: Sensorless Synchronous Motor Drives
1 / 22 Lecture 8: Sensorless Synchronous Motor Drives ELEC-E8402 Control of Electric Drives and Power Converters (5 ECTS) Marko Hinkkanen Spring 2017 2 / 22 Learning Outcomes After this lecture and exercises
More informationPERFORMANCE ANALYSIS OF DIRECT TORQUE CONTROL OF 3-PHASE INDUCTION MOTOR
PERFORMANCE ANALYSIS OF DIRECT TORQUE CONTROL OF 3-PHASE INDUCTION MOTOR 1 A.PANDIAN, 2 Dr.R.DHANASEKARAN 1 Associate Professor., Department of Electrical and Electronics Engineering, Angel College of
More informationSEVERAL methods are available for rotor speed estimation
146 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 53, NO. 1, FEBRUARY 2006 Sliding-Mode MRAS Speed Estimators for Sensorless Vector Control of Induction Machine Mihai Comanescu, Student Member, IEEE,
More informationIndependent Control of Speed and Torque in a Vector Controlled Induction Motor Drive using Predictive Current Controller and SVPWM
Independent Control of Speed and Torque in a Vector Controlled Induction Motor Drive using Predictive Current Controller and SVPWM Vandana Peethambaran 1, Dr.R.Sankaran 2 Assistant Professor, Dept. of
More informationA Novel Adaptive Estimation of Stator and Rotor Resistance for Induction Motor Drives
A Novel Adaptive Estimation of Stator and Rotor Resistance for Induction Motor Drives Nagaraja Yadav Ponagani Asst.Professsor, Department of Electrical & Electronics Engineering Dhurva Institute of Engineering
More informationSpeed Sensorless Vector Control of Induction Motors Based on Robust Adaptive Variable Structure Control Law
Speed Sensorless Vector Control of Induction Motors Based on Robust Adaptive Variable Structure Control Law O. Barambones, A.J. Garrido, F.J. Maseda and P. Alkorta Dpto. Ingeniería de Sistemas y Automática,
More informationIN the above paper [1] the local observability of the induction machine (IM) and the permanent
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS 1 Discussion on AC Drive Observability Analysis Mohamad Koteich, Student Member, IEEE, Abdelmalek Maloum, Gilles Duc and Guillaume Sandou arxiv:1512.01462v1
More informationA higher order sliding mode controller for a class of MIMO nonlinear systems: application to PM synchronous motor control
A higher order sliding mode controller for a class of MIMO nonlinear systems: application to PM synchronous motor control S Laghrouche, F Plestan and A Glumineau Abstract A new robust higher order sliding
More informationSensorless Sliding Mode Control of Induction Motor Drives
Sensorless Sliding Mode Control of Induction Motor Drives Kanungo Barada Mohanty Electrical Engineering Department, National Institute of Technology, Rourkela-7698, India E-mail: kbmohanty@nitrkl.ac.in
More informationA sliding mode control for a wound rotor synchronous generator with an isolated RL load
21 American Control Conference Marriott Waterfront, Baltimore, MD, USA June 3-July 2, 21 ThA5.6 A sliding mode control for a wound rotor synchronous generator with an isolated RL load R.S. Muñoz-Aguilar,
More informationSimplified EKF Based Sensorless Direct Torque Control of Permanent Magnet Brushless AC Drives
International Journal of Automation and Computing (24) 35-4 Simplified EKF Based Sensorless Direct Torque Control of Permanent Magnet Brushless AC Drives Yong Liu, Ziqiang Zhu, David Howe Department of
More informationRobust Controller Design for Speed Control of an Indirect Field Oriented Induction Machine Drive
Leonardo Electronic Journal of Practices and Technologies ISSN 1583-1078 Issue 6, January-June 2005 p. 1-16 Robust Controller Design for Speed Control of an Indirect Field Oriented Induction Machine Drive
More informationA New Predictive Control Strategy Dedicated to Salient Pole Synchronous Machines
A New Predictive Control Strategy Dedicated to Salient Pole Synchronous Machines Nicolas Patin Member IEEE University of Technology of Compiègne Laboratoire d Electromécanique de Compiègne Rue Personne
More informationSpeed Sensorless Field Oriented Control of Induction Machines using Flux Observer. Hisao Kubota* and Kouki Matsuse**
Speed Sensorless Field Oriented Control of Induction Machines using Flux Observer Hisao Kubota* and Kouki Matsuse** Dept. of Electrical Engineering, Meiji University, Higashimit Tama-ku, Kawasaki 214,
More informationSensorless Field Oriented Control of Permanent Magnet Synchronous Motor
International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347 5161 2015 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Sensorless
More informationAnakapalli Andhra Pradesh, India I. INTRODUCTION
Robust MRAS Based Sensorless Rotor Speed Measurement of Induction Motor against Variations in Stator Resistance Using Combination of Back Emf and Reactive Power Methods Srikanth Mandarapu Pydah College
More informationParametric Variations Sensitivity Analysis on IM Discrete Speed Estimation
Leonardo Electronic Journal of Practices and Technologies ISSN 1583-1078 Issue 11, July-December 007 p. 19-36 Parametric Variations Sensitivity Analysis on IM Discrete Speed Estimation Mohamed BEN MESSAOUD
More informationDynamic Modeling of Surface Mounted Permanent Synchronous Motor for Servo motor application
797 Dynamic Modeling of Surface Mounted Permanent Synchronous Motor for Servo motor application Ritu Tak 1, Sudhir Y Kumar 2, B.S.Rajpurohit 3 1,2 Electrical Engineering, Mody University of Science & Technology,
More informationVector Controlled Sensorless Estimation and Control of Speed of Induction Motors
Vector Controlled Sensorless Estimation and Control of Speed of Induction Motors Gayatri Gite Electrical Engineering Department SSSIST Sehore Bhopal, India Prabodh Khampariya Electrical Engineering Department
More informationTHE approach of sensorless speed control of induction motors
IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 41, NO. 4, JULY/AUGUST 2005 1039 An Adaptive Sliding-Mode Observer for Induction Motor Sensorless Speed Control Jingchuan Li, Longya Xu, Fellow, IEEE, and
More information2014 Texas Instruments Motor Control Training Series. -V th. Dave Wilson
204 Texas Instruments Motor Control Training Series V th Speed Sensorless FOC P Commanded Rotor Speed Commanded i d = 0 Commanded i q (torque) P I P V d V q Reverse ClarkePark Transform θ d V a V b V c
More informationA sub-optimal second order sliding mode controller for systems with saturating actuators
28 American Control Conference Westin Seattle Hotel, Seattle, Washington, USA June -3, 28 FrB2.5 A sub-optimal second order sliding mode for systems with saturating actuators Antonella Ferrara and Matteo
More informationJRE SCHOOL OF Engineering
JRE SCHOOL OF Engineering Class Test-1 Examinations September 2014 Subject Name Electromechanical Energy Conversion-II Subject Code EEE -501 Roll No. of Student Max Marks 30 Marks Max Duration 1 hour Date
More informationEstimation of speed in linear induction motor drive by MRAS using neural network and sliding mode control
Estimation of speed in linear induction motor drive by MRAS using neural network and sliding mode control M. Anka Rao 1, M. Vijaya kumar 2, O. Yugeswar Reddy 3 1 Asst. Professor, Dept. of Electrical Engg.,
More informationA new FOC technique based on predictive current control for PMSM drive
ISSN 1 746-7, England, UK World Journal of Modelling and Simulation Vol. 5 (009) No. 4, pp. 87-94 A new FOC technique based on predictive current control for PMSM drive F. Heydari, A. Sheikholeslami, K.
More informationDESIGN OF ROBUST CONTROL SYSTEM FOR THE PMS MOTOR
Journal of ELECTRICAL ENGINEERING, VOL 58, NO 6, 2007, 326 333 DESIGN OF ROBUST CONTROL SYSTEM FOR THE PMS MOTOR Ahmed Azaiz Youcef Ramdani Abdelkader Meroufel The field orientation control (FOC) consists
More informationProceedings of the 6th WSEAS/IASME Int. Conf. on Electric Power Systems, High Voltages, Electric Machines, Tenerife, Spain, December 16-18,
Proceedings of the 6th WSEAS/IASME Int. Conf. on Electric Power Systems, High Voltages, Electric Machines, Tenerife, Spain, December 16-18, 2006 196 A Method for the Modeling and Analysis of Permanent
More informationDESIGN AND MODELLING OF SENSORLESS VECTOR CONTROLLED INDUCTION MOTOR USING MODEL REFERENCE ADAPTIVE SYSTEMS
DESIGN AND MODELLING OF SENSORLESS VECTOR CONTROLLED INDUCTION MOTOR USING MODEL REFERENCE ADAPTIVE SYSTEMS Janaki Pakalapati 1 Assistant Professor, Dept. of EEE, Avanthi Institute of Engineering and Technology,
More informationOpen Access Permanent Magnet Synchronous Motor Vector Control Based on Weighted Integral Gain of Sliding Mode Variable Structure
Send Orders for Reprints to reprints@benthamscienceae The Open Automation and Control Systems Journal, 5, 7, 33-33 33 Open Access Permanent Magnet Synchronous Motor Vector Control Based on Weighted Integral
More information1234. Sensorless speed control of a vector controlled three-phase induction motor drive by using MRAS
1234. Sensorless speed control of a vector controlled three-phase induction motor drive by using MRAS Ali Saffet Altay 1, Mehmet Emin Tacer 2, Ahmet Faik Mergen 3 1, 3 Istanbul Technical University, Department
More information970 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 48, NO. 3, MAY/JUNE 2012
970 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 48, NO. 3, MAY/JUNE 2012 Control Method Suitable for Direct-Torque-Control-Based Motor Drive System Satisfying Voltage and Current Limitations Yukinori
More informationInternational Journal of Advance Engineering and Research Development SIMULATION OF FIELD ORIENTED CONTROL OF PERMANENT MAGNET SYNCHRONOUS MOTOR
Scientific Journal of Impact Factor(SJIF): 3.134 e-issn(o): 2348-4470 p-issn(p): 2348-6406 International Journal of Advance Engineering and Research Development Volume 2,Issue 4, April -2015 SIMULATION
More informationAn Adaptive Quasi-Sliding-Mode Rotor Position Observer-Based Sensorless Control for Interior Permanent Magnet Synchronous Machines
University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Faculty Publications from the Department of Electrical and Computer Engineering Electrical & Computer Engineering, Department
More information1863. Active-disturbance rejection control based on a novel sliding mode observer for PMSM speed and rotor position
1863. Active-disturbance rejection control based on a novel sliding mode observer for PMSM speed and rotor position Zhongcai Qiu 1, Jian Xiao 2, Song Wang 3 School of Electrical Engineering, Southwest
More informationLIAPUNOV S STABILITY THEORY-BASED MODEL REFERENCE ADAPTIVE CONTROL FOR DC MOTOR
LIAPUNOV S STABILITY THEORY-BASED MODEL REFERENCE ADAPTIVE CONTROL FOR DC MOTOR *Ganta Ramesh, # R. Hanumanth Nayak *#Assistant Professor in EEE, Gudlavalleru Engg College, JNTU, Kakinada University, Gudlavalleru
More informationBackstepping Control with Integral Action of PMSM Integrated According to the MRAS Observer
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 232-3331, Volume 9, Issue 4 Ver. I (Jul Aug. 214), PP 59-68 Backstepping Control with Integral Action of PMSM
More informationAngle-Sensorless Zero- and Low-Speed Control of Bearingless Machines
216 IEEE IEEE Transactions on Magnetics, Vol. 52, No. 7, July 216 Angle-Sensorless Zero- and Low-Speed Control of Bearingless Machines T. Wellerdieck, T. Nussbaumer, J. W. Kolar This material is published
More informationImproved efficiency of a fan drive system without using an encoder or current sensors
Improved efficiency of a fan drive system without using an encoder or current sensors Tian-Hua Liu, Jyun-Jie Huang Department of Electrical Engineering, National Taiwan University of Science Technology,
More information2016 Kappa Electronics Motor Control Training Series 2016 Kappa Electronics LLC. -V th. Dave Wilson Co-Owner Kappa Electronics.
2016 Kappa Electronics Motor Control Training Series 2016 Kappa Electronics LLC V th CoOwner Kappa Electronics www.kappaiq.com Speed Sensorless FOC P Commanded Rotor Speed Commanded i d = 0 Commanded i
More informationCogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing
EVS28 KINTEX, Korea, May 3-6, 215 Cogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing Soo-Gyung Lee 1, Kyung-Tae Jung 1, Seung-Hee Chai 1, and Jung-Pyo
More informationISSN: (Online) Volume 2, Issue 2, February 2014 International Journal of Advance Research in Computer Science and Management Studies
ISSN: 2321-7782 (Online) Volume 2, Issue 2, February 2014 International Journal of Advance Research in Computer Science and Management Studies Research Article / Paper / Case Study Available online at:
More informationEvaluation Method to Estimate Position Control Error in Position Sensorless Control Based on Pattern Matching Method
IEEJ Journal of Industry Applications Vol.7 No.1 pp.73 79 DOI: 10.1541/ieejjia.7.73 Paper Evaluation Method to Estimate Position Control Error in Position Sensorless Control Based on Pattern Matching Method
More informationFUZZY LOGIC BASED ADAPTATION MECHANISM FOR ADAPTIVE LUENBERGER OBSERVER SENSORLESS DIRECT TORQUE CONTROL OF INDUCTION MOTOR
Journal of Engineering Science and Technology Vol., No. (26) 46-59 School of Engineering, Taylor s University FUZZY LOGIC BASED ADAPTATION MECHANISM FOR ADAPTIVE LUENBERGER OBSERVER SENSORLESS DIRECT TORQUE
More information1439. Numerical simulation of the magnetic field and electromagnetic vibration analysis of the AC permanent-magnet synchronous motor
1439. Numerical simulation of the magnetic field and electromagnetic vibration analysis of the AC permanent-magnet synchronous motor Bai-zhou Li 1, Yu Wang 2, Qi-chang Zhang 3 1, 2, 3 School of Mechanical
More informationZero speed sensorless drive capability of fractional slot inset PM machine
Zero speed sensorless drive capability of fractional slot inset PM Adriano Faggion Nicola Bianchi Silverio Bolognani Emanuele Fornasiero Electric Drives Laboratory Department of Industrial Engineering
More informationEffect of Parametric Variations and Voltage Unbalance on Adaptive Speed Estimation Schemes for Speed Sensorless Induction Motor Drives
International Journal of Power Electronics and Drive System (IJPEDS) Vol. 6, No. 1, March 2015, pp. 77~85 ISSN: 2088-8694 77 Effect of Parametric Variations and Voltage Unbalance on Adaptive Speed Estimation
More informationMODEL REFERENCE ADAPTIVE CONTROL OF PERMANENT MAGNET SYNCHRONOUS MOTOR
Journal of ELECTRICAL ENGINEERING, VOL. 62, NO. 3, 2, 7 25 MODEL REFERENCE ADAPTIVE CONTROL OF PERMANENT MAGNET SYNCHRONOUS MOTOR Marián Tárník Ján Murgaš In this paper the classical theory of the direct
More informationA New Current Model Flux Observer for Wide Speed Range Sensorless Control of an Induction Machine
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 17, NO. 6, NOVEMBER 2002 1041 A New Current Model Flux Observer for Wide Speed Range Sensorless Control of an Induction Machine Habib-ur Rehman, Member, IEEE,
More informationSEMINAR ON ELECTRICAL ENGINEERING, INFORMATICS, AND ITS EDUCATION
SEMINAR ON ELECTRICAL ENGINEERING, INFORMATICS, AND ITS EDUCATION 2011 1 Sensorless Flux Vector Control of Induction Motor for Driving Centrifugal Pump Aripriharta 1, Rini Nur Hasanah 2 aripriharta@gmail.com,
More informationIEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY 1
IEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY 1 Robust Control With Exact Uncertainties Compensation: With or Without Chattering? Alejandra Ferreira, Member, IEEE, Francisco Javier Bejarano, and Leonid
More informationLecture 7: Synchronous Motor Drives
1 / 46 Lecture 7: Synchronous Motor Drives ELEC-E8402 Control of Electric Drives and Power Converters (5 ECTS) Marko Hinkkanen Spring 2017 2 / 46 Learning Outcomes After this lecture and exercises you
More informationRESEARCH ON REDUCING COGGING TORQUE IN PERMANENT MAGNET SYNCHRONOUS GENERATORS
U.P.B. Sci. Bull., Series C, Vol. 77, Iss. 3, 2015 ISSN 2286-3540 RESEARCH ON REDUCING COGGING TORQUE IN PERMANENT MAGNET SYNCHRONOUS GENERATORS Ion TRIFU 1 This paper presents different cogging torque
More informationAutomatic Control Systems. -Lecture Note 15-
-Lecture Note 15- Modeling of Physical Systems 5 1/52 AC Motors AC Motors Classification i) Induction Motor (Asynchronous Motor) ii) Synchronous Motor 2/52 Advantages of AC Motors i) Cost-effective ii)
More informationImproved Sliding Mode Observer for Position Sensorless Open-Winding Permanent Magnet Brushless Motor Drives
Progress In Electromagnetics Research M, Vol. 77, 147 156, 219 Improved Sliding Mode Observer for Position Sensorless Open-Winding Permanent Magnet Brushless Motor Drives Qing Lu 1, 2,LiQuan 1, *, Xiaoyong
More informationHigh Performance and Reliable Torque Control of Permanent Magnet Synchronous Motors in Electric Vehicle Applications
http://dx.doi.org/10.5755/j01.eee.19.7.159 ELEKTRONIKA IR ELEKTROTECHNIKA, ISSN 139-115, VOL. 19, NO. 7, 013 High Performance and Reliable Torque Control of Permanent Magnet Synchronous Motors in Electric
More informationDEVELOPMENT OF DIRECT TORQUE CONTROL MODELWITH USING SVI FOR THREE PHASE INDUCTION MOTOR
DEVELOPMENT OF DIRECT TORQUE CONTROL MODELWITH USING SVI FOR THREE PHASE INDUCTION MOTOR MUKESH KUMAR ARYA * Electrical Engg. Department, Madhav Institute of Technology & Science, Gwalior, Gwalior, 474005,
More informationAC Induction Motor Stator Resistance Estimation Algorithm
7th WSEAS International Conference on Electric Power Systems, High Voltages, Electric Machines, Venice, Italy, November 21-23, 27 86 AC Induction Motor Stator Resistance Estimation Algorithm PETR BLAHA
More informationNovel DTC-SVM for an Adjustable Speed Sensorless Induction Motor Drive
Novel DTC-SVM for an Adjustable Speed Sensorless Induction Motor Drive Nazeer Ahammad S1, Sadik Ahamad Khan2, Ravi Kumar Reddy P3, Prasanthi M4 1*Pursuing M.Tech in the field of Power Electronics 2*Working
More informationSensorless DTC-SVM of Induction Motor by Applying Two Neural Controllers
Sensorless DTC-SVM of Induction Motor by Applying Two Neural Controllers Abdallah Farahat Mahmoud Dept. of Electrical Engineering, Al-Azhar University, Qena, Egypt engabdallah2012@azhar.edu.eg Adel S.
More informationModeling Free Acceleration of a Salient Synchronous Machine Using Two-Axis Theory
1 Modeling ree Acceleration of a Salient Synchronous Machine Using Two-Axis Theory Abdullah H. Akca and Lingling an, Senior Member, IEEE Abstract This paper investigates a nonlinear simulation model of
More informationInertia Identification and Auto-Tuning. of Induction Motor Using MRAS
Inertia Identification and Auto-Tuning of Induction Motor Using MRAS Yujie GUO *, Lipei HUANG *, Yang QIU *, Masaharu MURAMATSU ** * Department of Electrical Engineering, Tsinghua University, Beijing,
More informationDirect Torque Control of 5-phase 10/8 Switched Reluctance Motor by Using Fuzzy Method
Direct Torque Control of 5-phase 10/8 Switched Reluctance Motor by Using Fuzzy Method M. Reza Feyzi, Yousef Ebrahimi and Mahdi Zeinali Abstract A Switched Reluctance Motor (SRM) has several desirable features,
More informationDESIGN AND IMPLEMENTATION OF SENSORLESS SPEED CONTROL FOR INDUCTION MOTOR DRIVE USING AN OPTIMIZED EXTENDED KALMAN FILTER
INTERNATIONAL JOURNAL OF ELECTRONICS AND COMMUNICATION ENGINEERING & TECHNOLOGY (IJECET) International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 ISSN 0976 6464(Print)
More informationModelling of Closed Loop Speed Control for Pmsm Drive
Modelling of Closed Loop Speed Control for Pmsm Drive Vikram S. Sathe, Shankar S. Vanamane M. Tech Student, Department of Electrical Engg, Walchand College of Engineering, Sangli. Associate Prof, Department
More informationState Estimation of DFIG using an Extended Kalman Filter with an Augmented State Model
State Estimation of DFIG using an Extended Kalman Filter with an Augmented State Model Mridul Kanti Malaar Department of Electronics and Electrical Engineering Indian Institute of Technology Guwahati,
More informationIEEE Transactions on Applied Superconductivity. Copyright IEEE.
Title Loss analysis of permanent magnet hybrid brushless machines with and without HTS field windings Author(s) Liu, C; Chau, KT; Li, W Citation The 21st International Conference on Magnet Technology,
More informationImplementation of Twelve-Sector based Direct Torque Control for Induction motor
International Journal of Engineering Science Invention ISSN (Online): 2319 6734, ISSN (Print): 2319 6726 Volume 2 Issue 4 ǁ April. 2013 ǁ PP.32-37 Implementation of Twelve-Sector based Direct Torque Control
More informationPosition with Force Feedback Control of Manipulator Arm
Position with Force Feedback Control of Manipulator Arm 1 B. K. Chitra, 2 J. Nandha Gopal, 3 Dr. K. Rajeswari PG Student, Department of EIE Assistant Professor, Professor, Department of EEE Abstract This
More informationAnalysis of Sensorless Controlled One Phase Brushless DC Motor
nalysis of Sensorless Controlled One Phase Brushless DC Motor BDEL-KRIM DUD Electrical and Computer Engineering Department Palestine Polytechnic University (PPU) P.O. Box 98 Hebron, el:+97--89, Fax:+97--78
More informationCogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing
EVS28 KINTEX, Korea, May 3-6, 215 Cogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing Soo-Gyung Lee 1, Kyung-Tae Jung 1, Seung-Hee Chai 1, and Jung-Pyo
More informationAnalytical Model for Sizing the Magnets of Permanent Magnet Synchronous Machines
Journal of Electrical Engineering 3 (2015) 134-141 doi: 10.17265/2328-2223/2015.03.004 D DAVID PUBLISHING Analytical Model for Sizing Magnets of Permanent Magnet Synchronous Machines George Todorov and
More informationDirect Flux Vector Control Of Induction Motor Drives With Maximum Efficiency Per Torque
Direct Flux Vector Control Of Induction Motor Drives With Maximum Efficiency Per Torque S. Rajesh Babu 1, S. Sridhar 2 1 PG Scholar, Dept. Of Electrical & Electronics Engineering, JNTUACEA, Anantapuramu,
More informationSpeed estimator for induction motor drive based on synchronous speed tracking
Sādhanā Vol. 4, Part 4, June 25, pp. 24 256. c Indian Academy of Sciences Speed estimator for induction motor drive based on synchronous speed tracking S B BODKHE,,MVAWARE 2, J G CHAUDHARI 3 and J G AGRAWAL
More informationKalman Filters Unifying Model-based and HF Injection-based Sensorless Control of PMSM Drives
Kalman Filters Unifying Model-based and HF Injection-based Sensorless Control of PMSM Drives Václav Šmídl Institute of Information Theory and Automation Prague, Czech Republic email: smidl@utia.cas.cz
More informationModeling and Simulation of Flux-Optimized Induction Motor Drive
Research Journal of Applied Sciences, Engineering and Technology 2(6): 603-613, 2010 ISSN: 2040-7467 Maxwell Scientific Organization, 2010 Submitted Date: July 21, 2010 Accepted Date: August 20, 2010 Published
More informationSpeed Control of Non-collocated Stator-Rotor Synchronous Motor with Application in Robotic Surgery
Speed Control of Non-collocated Stator-Rotor Synchronous Motor with Application in Robotic Surgery Alireza Mohammadi, Danielius Samsonas, Christian Di Natali, Pietro Valdastri, Ying Tan, Denny Oetomo Melbourne
More informationSpontaneous Speed Reversals in Stepper Motors
Spontaneous Speed Reversals in Stepper Motors Marc Bodson University of Utah Electrical & Computer Engineering 50 S Central Campus Dr Rm 3280 Salt Lake City, UT 84112, U.S.A. Jeffrey S. Sato & Stephen
More informationMathematical Modelling of Permanent Magnet Synchronous Motor with Rotor Frame of Reference
Mathematical Modelling of Permanent Magnet Synchronous Motor with Rotor Frame of Reference Mukesh C Chauhan 1, Hitesh R Khunt 2 1 P.G Student (Electrical),2 Electrical Department, AITS, rajkot 1 mcchauhan1@aits.edu.in
More informationA Robust Nonlinear Luenberger Observer for the Sensorless Control of SM-PMSM: Rotor Position and Magnets Flux Estimation
A Robust Nonlinear Luenberger Observer for the Sensorless Control of SM-PMSM: Rotor Position and Magnets Flux Estimation Nicolas Henwood 1, 2, Jeremy Malaize 1, and Laurent Praly 2 1 Control, Signal and
More informationFour-Switch Inverter-Fed Direct Torque control of Three Phase Induction Motor
Four-Switch Inverter-Fed Direct Torque control of Three Phase Induction Motor R.Dharmaprakash 1, Joseph Henry 2, P.Gowtham 3 Research Scholar, Department of EEE, JNT University, Hyderabad, India 1 Professor,
More informationRobust Non-Linear Direct Torque and Flux Control of Adjustable Speed Sensorless PMSM Drive Based on SVM Using a PI Predictive Controller
Journal of Engineering Science and Technology Review 3 (1) (2010) 168-175 Research Article JOURNAL OF Engineering Science and Technology Review www.jestr.org Robust Non-Linear Direct Torque and Flux Control
More informationSpeed Behaviour of PI and SMC Based DTC of BLDC Motor
Speed Behaviour of PI and SMC Based DTC of BLDC Motor Dr.T.Vamsee Kiran 1, M.Prasanthi 2 Professor, Dept. of EEE, DVR &Dr. HS MIC College of Technology, Andhra Pradesh, India 1 PG Student [PE], Dept. of
More informationPower density improvement of three phase flux reversal machine with distributed winding
Published in IET Electric Power Applications Received on 4th January 2009 Revised on 2nd April 2009 ISSN 1751-8660 Power density improvement of three phase flux reversal machine with distributed winding
More information() Observation, Estimation et Commande robuste non linéaires d actionneurs électriques sans capteur mécaniqu 1 / 52
Observation, Estimation et Commande robuste non linéaires d actionneurs électriques sans capteur mécanique. A.GLUMINEAU, IRCCyN Institut de Recherche en Communications et Cybernétique de Nantes, Nantes,
More informationSpeed Control of PMSM Drives by Using Neural Network Controller
Advance in Electronic and Electric Engineering. ISSN 2231-1297, Volume 4, Number 4 (2014), pp. 353-360 Research India Publications http://www.ripublication.com/aeee.htm Speed Control of PMSM Drives by
More informationMassachusetts Institute of Technology Department of Electrical Engineering and Computer Science Electric Machines
Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science 6.685 Electric Machines Problem Set 10 Issued November 11, 2013 Due November 20, 2013 Problem 1: Permanent
More informationA Novel Method on Disturbance Analysis and Feed-forward Compensation in Permanent Magnet Linear Motor System
A Novel Method on Disturbance Analysis and Feed-forward Compensation in Permanent Magnet Linear Motor System Jonghwa Kim, Kwanghyun Cho, Hojin Jung, and Seibum Choi Department of Mechanical Engineering
More informationHigher order sliding mode control based on adaptive first order sliding mode controller
Preprints of the 19th World Congress The International Federation of Automatic Control Cape Town, South Africa. August 4-9, 14 Higher order sliding mode control based on adaptive first order sliding mode
More informationAn improved deadbeat predictive current control for permanent magnet linear synchronous motor
Indian Journal of Engineering & Materials Sciences Vol. 22, June 2015, pp. 273-282 An improved deadbeat predictive current control for permanent magnet linear synchronous motor Mingyi Wang, iyi i, Donghua
More information