arxiv: v1 [cond-mat.mtrl-sci] 1 Nov 2018
|
|
- Magdalene Todd
- 5 years ago
- Views:
Transcription
1 3-omega method for thermal roerties of thin film multilayers Leandro N. Acquaroli Deartment of Engineering Physics, Ecole Polytechnique Montreal P.O. Box 679, Station Centre-Ville, Montreal (QC) H3C 3A7, Canada November 5, 8 Short review on the different models for the electro-thermal 3-omega method. We resent the deduction of the fundamental relation between the 3ω voltage with the temerature rise to determine the thermal conductivity. The usage of the anisotroy of the films allows a smooth transition between D and D models. A comarison between the multilayer methods and analytical solutions are resented. arxiv:8.57v [cond-mat.mtrl-sci] Nov 8 I. Introduction In the 3-omega method, a metal line is deosited on the surface of the secimen of interest to serve as both the heating source and thermometer detector Fig.. An alternating current of frequency ω is assed through the wire, I ω, inducing a Joule heating event in the wire, Q ω = I ω R, where R is the steady state electrical resistance of the wire. The heating event causes a second harmonic temerature rise in the samle, T ω, which is a function of the thermohysical roerties of the underlying samle. The electrical resistance of the wire varies linearly with resect to temerature R/ T across moderate temerature ranges in which the metal does not undergo a hase change. This temerature varying resistance, R ω, induced by T ω rovides the third harmonic voltage oscillation, from which the exeriment obtains its name, via Ohm s law: V 3ω = R ω I ω. This quantity can be measured by a lock-in amlifier (which often serves as the function generator as well) (,). For small temerature changes, the resistance of the filament varies with temerature as (3,4) R = R ( + β T ), () where β is the temerature coefficient of resistance TCR, and R and R are the resistances at temeratures T and T + T, resectively. The ower dissiated by the heater/rtd from now on referred to simly as the heater due to Joule heating is defined as P = I h R h, () where I h and R h are the heater current and resistance resectively. The alternating current assing through the heater is given as I h (t) = I h, R h,, (3) where I h, is the eak amlitude of the nominal heater current at a frequency ω. Assuming that the change in resistance is negligible comared to the amlitude of the current, the instantaneous ower can be written as P (t) = I h, R h, [ + cos(ωt)], (4) where R h, is the nominal heater resistance. Then, The ower can be searated into two comonents: a constant Fig. : Schematic of the metal line filament deosited on a secimen used for the 3ω measurements. l h and b h denote the heater length and half-width, resectively. The contact ads are used to make electrical contact with the microfabricated heater, where the current and voltages inuts are deicted as well. An AC current source is thought for this. comonent indeendent of time and an oscillating comonent: P DC = I h, R h, = P (5) P AC (t) = I h, R h, cos(ωt) = P cos(ωt). (6) The average ower dissiated by the heater is also called the root mean square (rms) ower, which is half of the ower dissiated by a DC current of the same amlitude, defined as P rms = I h,rms R h, = P, (7) where the rms heater current is given by τ I h,rms = I τ h (t) dt ω π/ω = I h, cos π (ωt)dt = I h,. (8) Assuming that the heater circuit is stable, i.e., that all the transient erturbations decay over time, the steady-state harmonic temerature oscillations in the metal filament roduce harmonic variations in the resistance given by R h (t) = R h, [+β h T DC +β h T AC cos(ωt+φ)], (9) where R h, is the nominal room temerature resistance of 8
2 of the heater, T DC is the steady-state temerature increase due to the rms ower dissiated by the filament, T AC is the magnitude of the steady-state temerature oscillations due to the sinusoidal comonent of the ower and φ is the hase angle between the temerature oscillations and the excitation current. The resulting voltage across the sensor is obtained by multilying the inut current be the heater resistance yielding V h (t) = I h, R h, [( + β h T DC ) cos(ωt) + β h T AC cos(ωt + φ) + ] β h T AC cos(3ωt + φ). () The 3ω and ω comonents in the voltage with hase shift result from multilying the ω term in the resistance with the inut current oscillating at the frequency ω. We can exress the 3ω amlitude as amlitude as V h,3ω = V h, β h T AC = V h, β h T ω, () where V h, = I h, R h,, and T ω is the comlex AC temerature oscillations at ω. This is the fundamental result for the 3ω method, which can be exressed in general terms of transfer functions (5), since by measuring the voltage at the frequency 3ω one is able to deduce the in-hase R(T ω ) and out-of-hase I(T ω ) comonents of the temerature oscillations. Both the magnitude and hase of the temerature oscillations vary with excitation frequency, due to the finite thermal-diffusion time τ D of the secimen. The thermal-diffusion time required for a thermal wave to roagate a distance L is given by (6) τ D = L α, () where α is the thermal diffusivity, which is defined as the ratio of thermal conductivity k to volumetric heat caacity c. In turn, the thermal-diffusion angular frequency is ω D = π = πα τ D L. (3) In the limit of infinite thermal diffusivity i.e., infinite thermal conductivity, heat roagates with infinite velocity such that the temerature is constant throughout the secimen. This leads to undamed temerature oscillations with zero hase lag. Conversely, zero thermal diffusivity (i.e., infinite volumetric heat caacity), results in no heat roagation, zero oscillation amlitude, and large hase lag. Note that the dissiation of the rms ower is indeendent of the frequency resonse of the secimen since it is constant with time. II. Heat diffusion from an infinite lanar heater with sinusoidal heating The sinusoidal current with frequency ω assing through the heater results in a steady DC temerature rise and Fig. : One dimensional heat flow from a thin infinitely long lane heater on a substrate. Heat enters the secimen uniformly over the width of the heater and edge-effects are not considered. The zero level of x-coordinate is located at the heater/secimen interface. an oscillating AC temerature comonent (4). The DC comonent creates a constant temerature gradient into the secimen while the AC art results in thermal waves diffusing into the secimen at frequency ω. Solving the heat equation in lanar coordinates ermits to determine the lag φ between the heater temerature and T ω. Consider Fig.. The heat diffusion equation to be solved for the system reads T xx α T t =. (4) In the case of sinusoidal heating the temerature can be searated into time and satially deendent arts T (x, t) = Θ(x) ex(iωt). (5) Relacing (5) into (4), erforming differentiation and dividing by ex(iωt) yields: d Θ dx iω α Θ =. (6) The solution of (6) can be exressed as Θ(x) = Θ ex( qx), for x >, (7) where q is the thermal wavenumber defined as iω ω ω q = = ( + i) α α = ex(iπ/4). (8) α Plugging (6) and (7) into (5) gives T (x, t) = Θ ex(iωt qx). (9) Consider one of the boundary condition to be Φ x + = k dt dx x + = kqθ ex(iωt) = kθ ex(iωt iπ/4). () The flux equals the oscillating heat comonent roduced in the heater er unit area. The oscillating ower of the heater can be written in comlex notation, according to (6): P cos(ωt) = P R[ex(iωt)]. () Dividing the comlex ower by the heater area A, setting it equal to the heat flux from () and dividing both sides of 8
3 3 K (w) I (w) Fig. 3: The geometry of an infinite circular cylinder with one dimensional line heater running through the cylinder axis. by ex(iωt) gives Θ = P α ex( iπ/4). () Ak ω Finally, relacing this last result into (9) roduces T ω (x, t) = P α ex(iωt qx iπ/4) (3) Ak ω establishing that the temerature rise lags the heater current by φ = π/4, with a ω / deendence. III. Heat diffusion from a line heater inside a cylindrical secimen To understand how to use the 3ω method to determine the thermal conductivity of a secimen, it is convenient to start by solving the heat equation of an infinitely long cylinder, when heated from an inside linear heater at a distance r = x + y Fig. 3. The volume of the secimen is considered to be infinite, with no axial or circumferential temerature gradients. The heat equation to be solved for this system reads as follow (7) : T rr + r T r α T t =. (4) Given that the heating ower is sinusoidal, the solution for this equation can be written as T (r, t) = Θ(r) ex(iωt). (5) Introducing (5) into (4), erforming differentiation, and dividing by ex(iω), gives d Θ dr + r dθ dr q Θ =, (6) where q = iω/α, is the thermal wavenumber. Performing change of variables w = qr, leads to the zero-th order modified Bessel differential equation, w d Θ dw + w dθ dw w Θ =, (7) whose solution can be written as Θ(w) = c I (w) + c K (w), (8) where I (w) is the zero-th order modified Bessel function of the first kind, and K (w) is the zero-th order modified Argument, w Fig. 4: Behavior of the Bessel functions. Bessel function of the second kind. The temerature rofile of the system it is suosed to decay as r, then it is required to set c = Fig. 4. Then, the second boundary condition can be written in terms of the heat flux at r = r : Φ r=r = k dθ dr r=r = c k dk (qr) dr r=r = c kqk (qr ). (9) On the other hand, the heat flux from the heater through a cylindrical surface at r = r is related to the ower and the cylinder area A cyl by Φ r=r = P A cyl = P πr l h ex(iωt). (3) Equating (9) and (3), yields c = P πkl h qr K (qr ) = P πkl h, (3) since wk (w) when w. Then, Θ = P K (qr) πkl h. (3) Plugging last equation into (5), gives T ω (r, t) = P K (qr) πkl h ex(iωt). (33) IV. One-dimensional line heater at the surface of the secimen By halving the cylinder of Fig. 3 the heater remains at the surface of the secimen. The result for infinite volume can used to exress the temerature oscillations for infinite half-volume. Halving the volume means that twice as much of heat flux flows into the remaining volume, assuming no radiation, convection or conduction on the surface. Thus, 3 of 8
4 L. N. Acquaroli. 3-omega method for thermal roerties of thin film multilayers. Heater inside a cylindrical secimen: K (qr) ex(iωt) ωt [ π ] qr.5 ber, m u.5 ven a W Fig. 5: Visualization of the normalized real art of equation (34). The oscillations decay raidly away from the heater and are even in the time-domain. (33) becomes K (qr) ex(iωt). (34) πk In Fig. 5 it is deicted the normalized real art of Tω πk/, where is the ower er unit length of the heater. The hysical secimen may not be a semi-infinite solid, but rather has a finite thickness. Since the thermal waves decay raidly away from the heat source following a modified Bessel function of the second kind it must ensured that the enetration deth of the thermal wave is much less than the thickness of the secimen λ << d, where the thermal enetration deth is defined as r α λ= =. (35) q ω Tω (r, t) = Since the amlitude of an exonentially decaying function reduces to aroximately % of its initial magnitude after 5 length constants, it is exected that the magnitude of the thermal oscillations will decrease below % of its initial amlitude after 5 thermal enetration deths as the Bessel function decays faster than an exonential function. Thus, the secimen thickness must exceed 5 times the thermal enetration deth to be considered semi-infinite d >> 5λ. IV.. Effects of Finite Width of the Heater In order to generalize the D line solution to one with a finite-width, one needs to suerimose an infinite number of D line sources over the width of the heater (). This leads to a convolution integral, since the temerature at any arbitrary set of coordinates (x, y) within the secimen deends on its relative osition to all the line sources Fig. 6. Mathematically this is done by taking a Fourier transform of (34) with resect to x-coordinate as the temoral deendence is not of interest at this oint. Fig. 6: Schematic of a finite-width b line heater showing the temerature contributions from the extremities of the heater to a oint in the secimen. Only the oscillations at the surface are imortant, so y = and r = x. Now Fourier cosine transformation can be used because the temerature function is an even function. The Fourier cosine transform air is: Z fˆ(η) = f (x) cos(ηx)dx, (36) Z f (x) = fˆ(η) cos(ηx)dη. (37) π For the satial temerature oscillations the cosine transform reads Z Tω (η) = Tω (x) cos(ηx)dx Z = K (qη) cos(ηx)dη πk =. (38) πk η + q The finite width can be added into (38) by multilying it with the Fourier transform of the heat source as a function of the x-coordinate. Heat enters the secimen evenly over the width of the heater ranging from b to b. This behavior can be exressed as a rectangular function with values for x < b and elsewhere. According to the convolution theorem, the multilication of the Fourier transforms of (38) and the rectangular function equals the Fourier transform of the convolution of the functions in the x-sace: Z Tω (η) = rect(x) cos(ηx)dx πk η + q sin(ηb) =. (39) πk η + q Taking the inverse transform gives Z sin(ηb) cos(ηx) Tω (x) = dη. πk (ηb) η + q (4) Equation (4) gives the form of temerature oscillations on the surface of the secimen a distance x away from the center of the heat source that has a finite width b. Since the thermometer and the heater are the same element the measured temerature is some average temerature over the width of the line. Exression (4) can be averaged by integrating it with resect to x from to b and dividing by b to give the temerature measured by the thermometer as 4 of 8
5 roosed by Cahill () : T ω = b b T ω (x)dx = πk sin (ηb) (ηb) dη. (4) η + q The asymtotic behavior of the last equation when q b << normally termed sloe-method for its deendence on ln(ω) can be written as (8) T ω = πk [ ln ( α b ) ln(ω) + ζ ] i 4k. (4) where ζ is a constant. By defining the reduced frequency, Ω = b ω/α, equation (4) results (9) : T ω = πk sin (ξ) ξ dξ. (43) ξ + iω With roer substitutions and calculations, the last exression is related to the Meijer G-function by (9) : T ω = i ( ) 4πkΩ G 4 iω,3/,,/,, (44) Asymtotic analysis gives two distinct regimes: T ω Ω = ( πk ln Ω + 3 ) γ iπ, (45) 4 T ω Ω = k ( i), (46) Ω where γ =.577 is the Euler constant. IV.. Thin film on a substrate The effect of the thin film on the substrate can be added as a thermal resistance indeendent of the driving frequency. In the 3ω method, the temerature dro across the film is inferred from the difference between the exerimental temerature rise of the heater and the calculated temerature rise of the bare substrate samle. The substrate thermal conductivity is determined from the sloe method alied to the exerimental temerature rise of the heater and usually a one-dimensional heat conduction model is assumed across the film. With these aroximations, the exerimental temerature rise of the heater on the film lus substrate system can be written as (8) T s+f,ω = T s,ω + d f bk f, (47) where subscrit f denotes film roerties e.g. d f is the thickness of the film and T s,ω is calculated based on Eq. (4). Considering the exression from Eq. (47), the film thermal conductivity as determined from the sloe-based 3ω method may be written as k f = d f b (T f,ω T s,ω ) avg, (48) where T f,ω is calculated from Eq. () with the measured voltages and TCR, and the average over the frequency range is erformed. In order to determine the thermal conductivity of the film, the calculated temerature dro across the film is averaged over the exerimental frequency range. If the system contains additional films, the thickness and thermal roerties of these films must be known in order to subtract their contribution from the total exerimental temerature rise. Another way to calculate the thermal conductivity of the film may be carried out with the so-called differential 3ω technique, where the thermal conductivity of the film is calculated using the average temerature rise difference exerimentally measured at the same ower inut by similar heaters deosited on the secimen and a reference samle without the film of interest (8) : k f = d f [( ) b Tω r+f ( ) b Tω r ], (49) avg where subscrit r+f corresonds to the structure that includes the samle film and the subscrit r refers to the reference structure only. Although the differential technique requires two sets of measurements, the film thermal conductivity determined from Eq. (49) is insensitive to the substrate thermal conductivity, and the contributions from any additional films is nearly eliminated by the measurement on the reference samle. For further details and considerations on the alicability of the sloe and differential methods, Borca-Tarsiuc (8) and Dames 3 () are recommended readings. V. Heat conduction across a D multilayer-film on a substrate system The heat-conduction model develoed by Borca-Tarsiuc was emloyed for the data analysis throughout the resent work. Shortly, the model resents a solution based on a two-dimensional heat-conduction model across a multilayer system and a uniform heat flux boundary condition between the heater and the to film. Disregarding the contribution of the thermal mass of the heater, the comlex temerature oscillations of a heater is given by (8) : where T ω = π k y, A j = A j A (η) B (η) sin (bη) dη (5) (bη) k y,j B j k y,j B j tanh(b j d j ) A j k y,j B j k y,j B j tanh(b j d j ) j =,..., n, B j = k xy,j η + iω, α y,j k xy = k x k y, A n = tanh(b n d n ) s., (5a) (5b) (5c) (5d) In the revious exressions, η is the integration variable, i =, n is the total number of layers including the substrate, j corresonds to the jth layer starting from the to, subscrit y denotes the cross-lane erendicular to the film/substrate interface, while x defines the in-lane coordinate, b and l are the half-width and length (where the voltage dro is read) of the heater, resectively, is the eak electrical ower er unit length, k is the thermal con- 5 of 8
6 Normalized temerature, (4k/)Tω 6 4 Heater on a silicon substrate 3 3 Reduced frequency, Ω Meijer-G Cahill Borca-Tarsiuc Matrix Fig. 7: Normalized T ω sectrum of isotroic bulk silicon with k y = 6 W m K, l = mm, b = 6.5 µm, =. W, calculated with Eqs. (43) Cahill, (44) Meijer-G, (5) Borca-Tarsiuc and (5) Matrix formalism. ductivity, α = k/(ρ c ) the thermal diffusivity (where ρ is the density and c is the secific heat caacity of the layer), ω indicates the angular frequency and d the thickness of the layer. Equation (5d) establishes the substrate boundary condition, where s takes the values for semi-infinite, for an adiabatic condition and - for an isothermal boundary when the substrate is finite. V.. Matrix formalism The matrix formalism is similar to that reorted elsewhere (,8,,). Consider a multilayer system in vacuum with the layers numbered from bottom to the to, to n, where the heater is in contact with the to layer. The 3ω signal is obtained from the ac temerature of the to surface of the to layer. An ac current at ω flows through the heater stri normal to the lane of age, generating heat at ω. The ac surface temerature for a multilayer system averaged over the stri, is thus () : with T ω = π λ j = k y,j B + (η) + B (η) A + (η) B (η) A (η) B + (η) k xy,j η + i ω α y,j, sin (ηb) dη (5) λ h (ηb) k xy,j = k x,j k y,j, (53) where the subscrit h first layer, j = n refers to the heater metal stri, A + (η), A (η), B + (η), and B (η) are arameters determined by a matrix rocedure analogous to that given in reference (). The recursion relations show symbolically how B + (η) and B (η) change if we add a layer, considering the thermal resistance of the interfaces (). For instance, since the semi-infinite boundary condition BC alies at the bottom of the substrate, for a heater on a substrate system we have: ( ) B + B = ( ) ( ) λ + λ + λ λ R λ λ λ λ R λ λ λ + λ λ R λ + λ λ λ R }{{}}{{} Interface i= BC (54) As we add layers to the system a recursive roduct develos as follow: ( ) B + n ( B = Λ U j Λ j (55) ) j= with the interface Λ j and transfer U j matrices defined as: Λ j = ( ) λj+ + λ j + λ j+ λ j R j λ j+ λ j λ j+ λ j R j λ j+ λ j+ λ j + λ j+ λ j R j λ j+ + λ j λ j+ λ j R j U j = ( ) ex ( uj d j ) ex (u j d j ) (56) (57) where u j = (λ j /k y,j ) is the transfer wave vector, d j is the thickness of layer j, and the deendence of all other arameters on η is imlied. Regardless of the number of layers, A + (η) = /, and A (η) = / (i.e., the heater is on the to of a the stack, otherwise see Bauer et al. 4). When j = nw, then B + (η) =, and B (η) = considering semi-infinite boundary condition. The R j arameter it is defined as the thermal boundary resistance at an interface j, known as the Kaitza resistance (). Comaring between the Cahill model, Meijer-G function, Borca-Tarsiuc model and the matrix formalism for a heater on a substrate system Fig. 7, we can see that the numerical integration solutions to the equation agree each other. As ointed out by Cahill (), the integratin is an aroximation, which actually we see that largely differs from the Meijer-G solution in the low frequency range, articularly the real art, with an absolute difference u to.5 in the normalized scale. The difference for the out of hase art, is narrowed for all solutions. We must use the analytical model whenever exerimenting with heater on a substrate, leaving to any of the recursive formalism for multilayer systems. We need to consider these results since the thermal conductivity is obtained from the real art of the temerature rise. For the silicon examle, the error becomes negligible as the frequency is over Hz. For a two layer system, the real art of the temerature rise of Borca-Tarsiuc model matches that of the matrix formalism Fig. 8. There is no close solution the author is aware of of the integrals involving recurrent multilayer information. VI. Effect of the metal interface on the system In order to consider the heat conduction effects inside the heater, its heat caacitance (ρ h c h ) and thickness d h, and the thermal resistance R h between the heater and the film in contact with the heater should be included into the 6 of 8
7 Normalized temerature, (4k/)Tω Heater on a film-on-a-silicon-substrate 4 Reduced frequency, Ω Borca-Tarsiuc Matrix Fig. 8: T ω sectrum of an isotroic µm-thick film on bulk silicon, with k y =. W m K keeing the rest of the values as calculated in Fig. 7, calculated with Eqs. (5) Borca-Tarsiuc and (5) Matrix formalism. model. ρ h and c h are the density and the secific heat caacity of the heater, resectively. Under these conditions the comlex temerature rise of the heater is given by the following exression: ( ) T ω + R h T ω,h = ( b ). (58) b + i ω ρ h c h d h R h + T ω VII. Effects of black-body radiation and convection The ower is lost by radiation from the surface of the samle at osition x according to: 4ɛσT 3 T (x). To evaluate the influence of this radiative term, to Eq. (4), Cahill has roosed a corrected factor to the average temerature rise given by (,3) : T ω = π sin (ηb) ( (ηb) k )dη, (59) η + q + ɛσt 3 where ɛ is the emissivity, and σ = W m K 4 is the Stefan-Boltzmann constant. Fig. 9 shows a numerical analysis of the effect of the temerature on a substrate of. W m K, with thermal diffusivity m s, b = 6.5 µm and l = mm. The effects of radiation on the temerature oscillations are shown for several temerature values using an emissivity of. The influence of radiation is small, corresonding to an error in determining thermal conductivity less than % (,3). Dames exlained that the combined effects can be disregarded given some considerations are taken into account for the exerimental system (). Values for the microscoic heater stris as used in 3ω exeriments are not readily aarent in the literature but will be subject to two cometing effects. The narrower heater width tends to increase the convection heat transfer coefficient h conv, while the surrounding unheated substrate tends to imede air flow Normalized temerature, (4k/)Tω Reduced frequency, Ω 6 Fig. 9: Temerature rise variation for different temeratures in the black-body radiation effect Eqs. (59), taking ɛ =. and reduce h conv. The relative imact of heat losses is Q rad+conv Q cond 8 4 Temerature, T [K] h q s k s, (6) where Q rad, Q conv and Q cond are the radiation, convective and conduction heat ower, resectively, while q s and k s are the substrate thermal wavelength and thermal conductivity, resectively, and h = h conv + h rad is the total heat transfer coefficient convective lus radiative. For a tyical exeriment with q s µm and k s W m K, the losses are <% if h <. W m K, which as noted above is very easily satisfied. In contrast, DC measurements on larger samles with characteristic lengths at the centimeter scale would reduce the threshold h to the low hundreds of W m K. [] D. G. Cahill. Thermal conductivity measurement from 3 to 75 K: the 3ω method. Rev. Sci. Instrum., 6():8 88, 99. [] M. L. Bauer and P. M. Norris. General bidirectional thermal characterization via the 3ω technique. Rev. Sci. Instrum., 85(6), 4. [3] D. de Koninck. Thermal Conductivity Measurements Using the 3-Omega Technique: Alication to Power Harvesting Microsystems. PhD thesis, McGill University, Montreal, Canada, 8. [4] T. Häninnen. Imlementing the 3-Omega Technique for Thermal Conductivity Measurements. University of Jyväskylä. Aril 3. Finland. [5] C. Dames and G. Chen. ω, ω, and 3ω methods for measurements of thermal roerties. Rev. Sci. Instrum., 76(), 5. [6] N. O. Birge. Secific-heat sectroscoy of glycerol and roylene glycol near the glass transition. Phys. Rev. B, 34:63 64, of 8
8 [7] J. C. Jaeger H. S. Carslaw. Conduction of heat in solids. Oxford University Press, 959. [8] T. Borca-Tasciuc, A. R. Kumar, and G. Chen. Data reduction in 3ω method for thin-film thermal conductivity determination. Rev. Sci. Instrum., 7(4):39,. [9] J.-Y. Duquesne, D. Fournier, and C. Frétigny. Analytical solutions of the heat diffusion equation for 3ω method geometry. J. Al. Phys., 8(8),. [] C. Dames. Measuring the thermal conductivity of thin films: 3-omega and related electrothermal methods. In Annual Review of Heat Transfer, volume 6, chater. Begell House Digital Library, 3. [] D. Novotny J. H. Kim, A. Feldman. Alication of the three omega thermal conductivity measurement method to a film on a substrate of finite thickness. J. Al. Phys., 86:3959, 999. [] K. Chen B. W. Olson, S. Graham. A ractical extension of the 3ω method to multilayer structures. Rev. Sci. Instrum., 76:539, 5. [3] David G. Cahill and R. O. Pohl. Thermal conductivity of amorhous solids above the lateau. Phys. Rev. B, 35: , of 8
Wolfgang POESSNECKER and Ulrich GROSS*
Proceedings of the Asian Thermohysical Proerties onference -4 August, 007, Fukuoka, Jaan Paer No. 0 A QUASI-STEADY YLINDER METHOD FOR THE SIMULTANEOUS DETERMINATION OF HEAT APAITY, THERMAL ONDUTIVITY AND
More informationChapter 5. Transient Conduction. Islamic Azad University
Chater 5 Transient Conduction Islamic Azad University Karaj Branch 1 Transient Conduction Many heat transfer roblems are time deendent Changes in oerating conditions in a system cause temerature variation
More informationJournal of System Design and Dynamics
Vol. 5, No. 6, Effects of Stable Nonlinear Normal Modes on Self-Synchronized Phenomena* Hiroki MORI**, Takuo NAGAMINE**, Yukihiro AKAMATSU** and Yuichi SATO** ** Deartment of Mechanical Engineering, Saitama
More informationEKT103 ELECTRICAL ENGINEERING
EKT13 EECTRCA ENGNEERNG Chater 1 Three-Phase System 1 COURSE OUTCOME (CO) CO1: Ability to define and exlain the concet of single-hase and threehase system. 2 Revision A sinusoid is a signal that has the
More informationSection 4: Electromagnetic Waves 2
Frequency deendence and dielectric constant Section 4: Electromagnetic Waves We now consider frequency deendence of electromagnetic waves roagating in a dielectric medium. As efore we suose that the medium
More informationpp physics, RWTH, WS 2003/04, T.Hebbeker
1. PP TH 03/04 Accelerators and Detectors 1 hysics, RWTH, WS 2003/04, T.Hebbeker 2003-12-03 1. Accelerators and Detectors In the following, we concentrate on the three machines SPS, Tevatron and LHC with
More informationNONRELATIVISTIC STRONG-FIELD APPROXIMATION (SFA)
NONRELATIVISTIC STRONG-FIELD APPROXIMATION (SFA) Note: SFA will automatically be taken to mean Coulomb gauge (relativistic or non-diole) or VG (nonrelativistic, diole-aroximation). If LG is intended (rarely),
More informationThe extreme case of the anisothermal calorimeter when there is no heat exchange is the adiabatic calorimeter.
.4. Determination of the enthaly of solution of anhydrous and hydrous sodium acetate by anisothermal calorimeter, and the enthaly of melting of ice by isothermal heat flow calorimeter Theoretical background
More informationUniversity of North Carolina-Charlotte Department of Electrical and Computer Engineering ECGR 4143/5195 Electrical Machinery Fall 2009
University of North Carolina-Charlotte Deartment of Electrical and Comuter Engineering ECG 4143/5195 Electrical Machinery Fall 9 Problem Set 5 Part Due: Friday October 3 Problem 3: Modeling the exerimental
More informationUniformly best wavenumber approximations by spatial central difference operators: An initial investigation
Uniformly best wavenumber aroximations by satial central difference oerators: An initial investigation Vitor Linders and Jan Nordström Abstract A characterisation theorem for best uniform wavenumber aroximations
More informationChapter 12: Three-Phase Circuits
Chater 1: Three-Phase Circuits 1.1 ntroduction 1. Balanced Three-Phase oltages 1.3 Balanced Wye-Wye connection 1.4 Balanced Wye-Delta Connection 1.7 Power in a Balanced System 1.1 NTRODUCTON A single-hase
More informationOn the relationship between sound intensity and wave impedance
Buenos Aires 5 to 9 Setember, 16 Acoustics for the 1 st Century PROCEEDINGS of the nd International Congress on Acoustics Sound Intensity and Inverse Methods in Acoustics: Paer ICA16-198 On the relationshi
More informationSimplifications to Conservation Equations
Chater 5 Simlifications to Conservation Equations 5.1 Steady Flow If fluid roerties at a oint in a field do not change with time, then they are a function of sace only. They are reresented by: ϕ = ϕq 1,
More informationChapter 6: Sound Wave Equation
Lecture notes on OPAC0- ntroduction to Acoustics Dr. Eser OLĞAR, 08 Chater 6: Sound Wave Equation. Sound Waves in a medium the wave equation Just like the eriodic motion of the simle harmonic oscillator,
More informationdn i where we have used the Gibbs equation for the Gibbs energy and the definition of chemical potential
Chem 467 Sulement to Lectures 33 Phase Equilibrium Chemical Potential Revisited We introduced the chemical otential as the conjugate variable to amount. Briefly reviewing, the total Gibbs energy of a system
More informationintegral invariant relations is not limited to one or two such
The Astronomical Journal, 126:3138 3142, 2003 December # 2003. The American Astronomical Society. All rights reserved. Printed in U.S.A. EFFICIENT ORBIT INTEGRATION BY SCALING AND ROTATION FOR CONSISTENCY
More informationarxiv: v1 [hep-ex] 8 Jun 2017
UCHEP 17 05 6 Aril 017 Prosects for time-deendent mixing and CP-violation measurements at Belle II arxiv:1706.0363v1 [he-ex] 8 Jun 017 Physics Deartment, University of Cincinnati, Cincinnati, Ohio 51 E-mail:
More information1 University of Edinburgh, 2 British Geological Survey, 3 China University of Petroleum
Estimation of fluid mobility from frequency deendent azimuthal AVO a synthetic model study Yingrui Ren 1*, Xiaoyang Wu 2, Mark Chaman 1 and Xiangyang Li 2,3 1 University of Edinburgh, 2 British Geological
More informationPhase transition. Asaf Pe er Background
Phase transition Asaf Pe er 1 November 18, 2013 1. Background A hase is a region of sace, throughout which all hysical roerties (density, magnetization, etc.) of a material (or thermodynamic system) are
More informationControllable Spatial Array of Bessel-like Beams with Independent Axial Intensity Distributions for Laser Microprocessing
JLMN-Journal of Laser Micro/Nanoengineering Vol. 3, No. 3, 08 Controllable Satial Array of Bessel-like Beams with Indeendent Axial Intensity Distributions for Laser Microrocessing Sergej Orlov, Alfonsas
More informationOn Using FASTEM2 for the Special Sensor Microwave Imager (SSM/I) March 15, Godelieve Deblonde Meteorological Service of Canada
On Using FASTEM2 for the Secial Sensor Microwave Imager (SSM/I) March 15, 2001 Godelieve Deblonde Meteorological Service of Canada 1 1. Introduction Fastem2 is a fast model (multile-linear regression model)
More informationME scope Application Note 16
ME scoe Alication Note 16 Integration & Differentiation of FFs and Mode Shaes NOTE: The stes used in this Alication Note can be dulicated using any Package that includes the VES-36 Advanced Signal Processing
More informationI Poles & zeros. I First-order systems. I Second-order systems. I E ect of additional poles. I E ect of zeros. I E ect of nonlinearities
EE C28 / ME C34 Lecture Chater 4 Time Resonse Alexandre Bayen Deartment of Electrical Engineering & Comuter Science University of California Berkeley Lecture abstract Toics covered in this resentation
More informationPrinciples of Computed Tomography (CT)
Page 298 Princiles of Comuted Tomograhy (CT) The theoretical foundation of CT dates back to Johann Radon, a mathematician from Vienna who derived a method in 1907 for rojecting a 2-D object along arallel
More informationInvariant yield calculation
Chater 6 Invariant yield calculation he invariant yield of the neutral ions and η mesons er one minimum bias collision as a function of the transverse momentum is given by E d3 N d 3 = d 3 N d dydφ = d
More informationVI. Electrokinetics. Lecture 31: Electrokinetic Energy Conversion
VI. Electrokinetics Lecture 31: Electrokinetic Energy Conversion MIT Student 1 Princiles 1.1 General Theory We have the following equation for the linear electrokinetic resonse of a nanochannel: ( ) (
More informationPolarization Mode Dispersion Mitigation through Spun Fibers
INTERNATIONAL JOURNAL O MICROWAVE AND OPTICAL TECHNOLOGY, 176 VOL.5 NO.3 MAY 1 Polarization Mode Disersion Mitigation through Sun ibers Dowluru Ravi Kumar*, Dr.. Prabhakara Rao * Lecturer in ECE, Deartment
More informationCharacterizing the Behavior of a Probabilistic CMOS Switch Through Analytical Models and Its Verification Through Simulations
Characterizing the Behavior of a Probabilistic CMOS Switch Through Analytical Models and Its Verification Through Simulations PINAR KORKMAZ, BILGE E. S. AKGUL and KRISHNA V. PALEM Georgia Institute of
More informationhal , version 1-7 May 2008
Author manuscrit, ulished in "N/P" 9-11 Aril 2008 Process nano scale mechanical roerties measurement of thin metal films using a novel addle cantilever test structure Chi-Jia Tong & Ming-Tzer Lin Institute
More informationInternational Journal of Mathematics Trends and Technology- Volume3 Issue4-2012
Effect of Hall current on Unsteady Flow of a Dusty Conducting Fluid through orous medium between Parallel Porous Plates with Temerature Deendent Viscosity and Thermal Radiation Harshbardhan Singh and Dr.
More information8.7 Associated and Non-associated Flow Rules
8.7 Associated and Non-associated Flow Rules Recall the Levy-Mises flow rule, Eqn. 8.4., d ds (8.7.) The lastic multilier can be determined from the hardening rule. Given the hardening rule one can more
More informationChurilova Maria Saint-Petersburg State Polytechnical University Department of Applied Mathematics
Churilova Maria Saint-Petersburg State Polytechnical University Deartment of Alied Mathematics Technology of EHIS (staming) alied to roduction of automotive arts The roblem described in this reort originated
More informationEfficiency of Microwave Heating of Weakly Loaded Polymeric Nanocomposites
Efficiency of Microwave Heating of Weakly Loaded Polymeric Nanocomosites Chen-Chih Tsai 1, Binyamin Rubin 1, Eugen Tatartschuk 1, Jeffery R.Owens 2, Igor Luzinov 1, Konstantin G. Kornev 1 1 Clemson University,
More informationarxiv: v1 [physics.data-an] 26 Oct 2012
Constraints on Yield Parameters in Extended Maximum Likelihood Fits Till Moritz Karbach a, Maximilian Schlu b a TU Dortmund, Germany, moritz.karbach@cern.ch b TU Dortmund, Germany, maximilian.schlu@cern.ch
More informationModelling a Partly Filled Road Tanker during an Emergency Braking
Proceedings of the World Congress on Engineering and Comuter Science 217 Vol II, October 25-27, 217, San Francisco, USA Modelling a Partly Filled Road Tanker during an Emergency Braking Frank Otremba,
More informationJournal of Thermal Science and Technology
Science and Technology Design Considerations of Porous Gas Enthaly Radiation Converters for Exhaust-Heat Recovery Systems Preecha KHANTIKOMOL and Kouichi KAMIUTO High-Temerature Heat Transfer Laboratory,
More information3.4 Design Methods for Fractional Delay Allpass Filters
Chater 3. Fractional Delay Filters 15 3.4 Design Methods for Fractional Delay Allass Filters Above we have studied the design of FIR filters for fractional delay aroximation. ow we show how recursive or
More informationPaper C Exact Volume Balance Versus Exact Mass Balance in Compositional Reservoir Simulation
Paer C Exact Volume Balance Versus Exact Mass Balance in Comositional Reservoir Simulation Submitted to Comutational Geosciences, December 2005. Exact Volume Balance Versus Exact Mass Balance in Comositional
More informationAn Improved Calibration Method for a Chopped Pyrgeometer
96 JOURNAL OF ATMOSPHERIC AND OCEANIC TECHNOLOGY VOLUME 17 An Imroved Calibration Method for a Choed Pyrgeometer FRIEDRICH FERGG OtoLab, Ingenieurbüro, Munich, Germany PETER WENDLING Deutsches Forschungszentrum
More information16. CHARACTERISTICS OF SHOCK-WAVE UNDER LORENTZ FORCE AND ENERGY EXCHANGE
16. CHARACTERISTICS OF SHOCK-WAVE UNDER LORENTZ FORCE AND ENERGY EXCHANGE H. Yamasaki, M. Abe and Y. Okuno Graduate School at Nagatsuta, Tokyo Institute of Technology 459, Nagatsuta, Midori-ku, Yokohama,
More informationThermal characterization of Au-Si multilayer using 3- omega method
Thermal characterization of Au-Si multilayer using 3- omega method Sunmi Shin Materials Science and Engineering Program Abstract As thermal management becomes a serious issue in applications of thermoelectrics,
More informationAll-fiber Optical Parametric Oscillator
All-fiber Otical Parametric Oscillator Chengao Wang Otical Science and Engineering, Deartment of Physics & Astronomy, University of New Mexico Albuquerque, NM 87131-0001, USA Abstract All-fiber otical
More informationrate~ If no additional source of holes were present, the excess
DIFFUSION OF CARRIERS Diffusion currents are resent in semiconductor devices which generate a satially non-uniform distribution of carriers. The most imortant examles are the -n junction and the biolar
More informationVIBRATION ANALYSIS OF BEAMS WITH MULTIPLE CONSTRAINED LAYER DAMPING PATCHES
Journal of Sound and Vibration (998) 22(5), 78 85 VIBRATION ANALYSIS OF BEAMS WITH MULTIPLE CONSTRAINED LAYER DAMPING PATCHES Acoustics and Dynamics Laboratory, Deartment of Mechanical Engineering, The
More informationFlow Velocity Measurement Principles of Hot Film Anemometry
Flow Velocity Measurement Princiles of Hot Film Anemometry The hot film anemometer (HFA) is made of a thin, structured, metallic resistive film ( heater ) which is deosited onto a substrate. In the oerating
More informationThe Noise Power Ratio - Theory and ADC Testing
The Noise Power Ratio - Theory and ADC Testing FH Irons, KJ Riley, and DM Hummels Abstract This aer develos theory behind the noise ower ratio (NPR) testing of ADCs. A mid-riser formulation is used for
More informationAdiabatic Shear Bands in Simple and Dipolar Plastic Materials
Adiabatic Shear Bands in Simle and Diolar Plastic Materials T W \-1RIGHT us Army Ballistic Research Laboratory Aberdeen Proving Ground, MD 215 R C BATRA University of Missouri-Rolla Rolla, Missouri 6541
More informationComparative study on different walking load models
Comarative study on different walking load models *Jining Wang 1) and Jun Chen ) 1), ) Deartment of Structural Engineering, Tongji University, Shanghai, China 1) 1510157@tongji.edu.cn ABSTRACT Since the
More informationChapter 2 Introductory Concepts of Wave Propagation Analysis in Structures
Chater 2 Introductory Concets of Wave Proagation Analysis in Structures Wave roagation is a transient dynamic henomenon resulting from short duration loading. Such transient loadings have high frequency
More informationFocused azimuthally polarized vector beam and spatial magnetic resolution below the diffraction limit
Research Article Vol. 33, No. 11 / November 2016 / Journal of the Otical Society of America B 2265 Focused azimuthally olarized vector beam and satial magnetic resolution below the diffraction limit MEHDI
More informationIdentification of the source of the thermoelastic response from orthotropic laminated composites
Identification of the source of the thermoelastic resonse from orthotroic laminated comosites S. Sambasivam, S. Quinn and J.M. Dulieu-Barton School of Engineering Sciences, University of Southamton, Highfield,
More informationANALYTICAL MODEL FOR THE BYPASS VALVE IN A LOOP HEAT PIPE
ANALYTICAL MODEL FOR THE BYPASS ALE IN A LOOP HEAT PIPE Michel Seetjens & Camilo Rindt Laboratory for Energy Technology Mechanical Engineering Deartment Eindhoven University of Technology The Netherlands
More informationThickness and refractive index measurements using multiple beam interference fringes (FECO)
Journal of Colloid and Interface Science 264 2003 548 553 Note www.elsevier.com/locate/jcis Thickness and refractive index measurements using multile beam interference fringes FECO Rafael Tadmor, 1 Nianhuan
More informationHigher order theory for analytic saddle point approximations to the Ρ Ρ and Ρ Ś reflected arrivals at a solid/solid interface
Higher order theory for analytic saddle oint aroximations to the Ρ Ρ and Ρ Ś reflected arrivals at a solid/solid interface P.F Daley ABSTACT The high frequency solution to the roblem of a Ρ P and Ρ S reflected
More informationCHAPTER-II Control Charts for Fraction Nonconforming using m-of-m Runs Rules
CHAPTER-II Control Charts for Fraction Nonconforming using m-of-m Runs Rules. Introduction: The is widely used in industry to monitor the number of fraction nonconforming units. A nonconforming unit is
More informationMODELING THE RELIABILITY OF C4ISR SYSTEMS HARDWARE/SOFTWARE COMPONENTS USING AN IMPROVED MARKOV MODEL
Technical Sciences and Alied Mathematics MODELING THE RELIABILITY OF CISR SYSTEMS HARDWARE/SOFTWARE COMPONENTS USING AN IMPROVED MARKOV MODEL Cezar VASILESCU Regional Deartment of Defense Resources Management
More informationOptical self-energy of superconducting Pb in the terahertz region
Otical self-energy of suerconducting Pb in the terahertz region T. Mori, 1 E. J. Nicol, 2, * S. Shiizuka, 1 K. Kuniyasu, 3 T. Nojima, 3 N. Toyota, 1 and J. P. Carbotte 4 1 Physics Deartment, Graduate School
More information4/8/2012. Example. Definition of the current: dq I = dt
4/8/0 Whenever electric charges of like signs move under the influence of an alied of electric field, an electric current is said to exist The current is the rate at which the charge moves in the wire.
More informationChapter 2 Thermal Analysis of Friction Welding
Chater 2 Thermal Analysis of Friction Welding Abstract Thermal energy is generated during the friction welding rocess. In this case, the solid surfaces rub against each other and heat is generated as a
More informationEE 508 Lecture 13. Statistical Characterization of Filter Characteristics
EE 508 Lecture 3 Statistical Characterization of Filter Characteristics Comonents used to build filters are not recisely redictable L C Temerature Variations Manufacturing Variations Aging Model variations
More informationP.O. Box 6079, Station Centre-Ville, Montreal, QC H3C 3A7, Canada.
Supplementary Material: Thermal properties of methyltrimethoxysilane aerogel thin films Leandro N. Acquaroli, 1, a) Pascal Newby, 2 Clara Santato, 1 1, b) and Yves-Alain Peter 1) Department of Engineering
More informationMake sure the exam paper has 8 pages plus an appendix page at the end.
UNIVERSITY OF CALIFORNIA College of Engineering Deartment of Electrical Engineering and Comuter Sciences Fall 2000 EE143 Midterm Exam #1 Family Name First name Signature Make sure the exam aer has 8 ages
More informationConvergence performance of the coupled-wave and the differential methods for thin gratings
Convergence erformance of the couled-wave and the differential methods for thin gratings Philie Lalanne To cite this version: Philie Lalanne. Convergence erformance of the couled-wave and the differential
More informationAtmosphere, Ocean and Climate Dynamics Answers to Chapter 4
Atmoshere, Ocean and Climate Dynamics Answers to Chater 4 1. Show that the buoyancy frequency, Eq.(4.22), may be written in terms of the environmental temerature rofile thus N 2 = g µ dte T E dz + Γ d
More informationFilters and Equalizers
Filters and Equalizers By Raymond L. Barrett, Jr., PhD, PE CEO, American Research and Develoment, LLC . Filters and Equalizers Introduction This course will define the notation for roots of olynomial exressions
More informationA PEAK FACTOR FOR PREDICTING NON-GAUSSIAN PEAK RESULTANT RESPONSE OF WIND-EXCITED TALL BUILDINGS
The Seventh Asia-Pacific Conference on Wind Engineering, November 8-1, 009, Taiei, Taiwan A PEAK FACTOR FOR PREDICTING NON-GAUSSIAN PEAK RESULTANT RESPONSE OF WIND-EXCITED TALL BUILDINGS M.F. Huang 1,
More informationNanoscale fluctuations and surface tension measurements in droplets using phase-resolved low-coherence interferometry
Nanoscale fluctuations and surface tension measurements in drolets using hase-resolved low-coherence interferometry Ru Wang, 1 Taewoo Kim, 2 Mustafa Mir, 2 and Gabriel Poescu 2, * 1 Quantitative Light
More informationHighly improved convergence of the coupled-wave method for TM polarization
. Lalanne and G. M. Morris Vol. 13, No. 4/Aril 1996/J. Ot. Soc. Am. A 779 Highly imroved convergence of the couled-wave method for TM olarization hilie Lalanne Institut d Otique Théorique et Aliquée, Centre
More informationThe individual electric and magnetic waves are in phase. The fields peak at the same position at the same time.
1 Part 3: Otics 3.1: Electromagnetic Waves An electromagnetic wave (light wave) consists of oscillating electric and magnetic fields. The directions of the electric and magnetic fields are erendicular.
More informationFactors Effect on the Saturation Parameter S and there Influences on the Gain Behavior of Ytterbium Doped Fiber Amplifier
Australian Journal of Basic and Alied Sciences, 5(12): 2010-2020, 2011 ISSN 1991-8178 Factors Effect on the Saturation Parameter S and there Influences on the Gain Behavior of Ytterbium Doed Fiber Amlifier
More informationTransport at surface nanostructures measured by four-tip STM q
Current Alied Physics 2 (2002) 465 471 www.elsevier.com/locate/ca Transort at surface nanostructures measured by four-ti STM q Shuji Hasegawa *, Ichiro Shiraki, Fuhito Tanabe, Rei Hobara Deartment of Physics,
More informationTHEORY AND PRACTICE OF MODULATED TEMPERATURE DIFFERENTIAL SCANNING CALORIMETRY
THEORY AND PRACTICE OF MODULATED TEMPERATURE DIFFERENTIAL SCANNING CALORIMETRY ANDREW A. LACEY 1, DUNCAN M. PRICE & MIKE READING 1. Deartment of Mathematics, Heriot-Watt University, Riccarton, Edinburgh
More informationSpeed of sound measurements in liquid Methane at cryogenic temperature and for pressure up to 10 MPa
LNGII - raining Day Delft, August 07 Seed of sound measurements in liquid Methane at cryogenic temerature and for ressure u to 0 MPa Simona Lago*, P. Alberto Giuliano Albo INRiM Istituto Nazionale di Ricerca
More informationHomogeneous and Inhomogeneous Model for Flow and Heat Transfer in Porous Materials as High Temperature Solar Air Receivers
Excert from the roceedings of the COMSOL Conference 1 aris Homogeneous and Inhomogeneous Model for Flow and Heat ransfer in orous Materials as High emerature Solar Air Receivers Olena Smirnova 1 *, homas
More informationSpin Diffusion and Relaxation in a Nonuniform Magnetic Field.
Sin Diffusion and Relaxation in a Nonuniform Magnetic Field. G.P. Berman, B. M. Chernobrod, V.N. Gorshkov, Theoretical Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 V.I. Tsifrinovich
More information97.398*, Physical Electronics, Lecture 8. Diode Operation
97.398*, Physical Electronics, Lecture 8 Diode Oeration Lecture Outline Have looked at basic diode rocessing and structures Goal is now to understand and model the behavior of the device under bias First
More informationLandau Theory of the Fermi Liquid
Chater 5 Landau Theory of the Fermi Liquid 5. Adiabatic Continuity The results of the revious lectures, which are based on the hysics of noninteracting systems lus lowest orders in erturbation theory,
More informationMET 4302 Midterm Study Guide 19FEB18
The exam will be 4% short answer and the remainder (6%) longer (1- aragrahs) answer roblems and mathematical derivations. The second section will consists of 6 questions worth 15 oints each. Answer 4.
More informationPHYSICAL REVIEW LETTERS
PHYSICAL REVIEW LETTERS VOLUME 81 20 JULY 1998 NUMBER 3 Searated-Path Ramsey Atom Interferometer P. D. Featonby, G. S. Summy, C. L. Webb, R. M. Godun, M. K. Oberthaler, A. C. Wilson, C. J. Foot, and K.
More informationImproved Perfectly Matched Layers for Acoustic Radiation and Scattering Problems
NATO Undersea Research Centre Partnering for Maritime Innovation Presented at the COMSOL Conference 008 Hannover Acoustics Session Wed 5 November 008, 13:00 15:40. Imroved Perfectly Matched Layers for
More informationAvailable online at ScienceDirect. Procedia Engineering 102 (2015 )
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 1 (15 ) 3 38 The 7th World Congress on Particle Technology (WCPT7) Characterization of Colloidal Particles using Electrical
More informationLinear diophantine equations for discrete tomography
Journal of X-Ray Science and Technology 10 001 59 66 59 IOS Press Linear diohantine euations for discrete tomograhy Yangbo Ye a,gewang b and Jiehua Zhu a a Deartment of Mathematics, The University of Iowa,
More informationYIELD OF SECONDARY ELECTRON EMISSION FROM CERAMIC MATERIALS OF HALL THRUSTER WITH SEGMENTED ELECTRODES
YELD OF SECONDARY ELECTRON EMSSON FROM CERAMC MATERALS OF HALL THRUSTER WTH SEGMENTED ELECTRODES A. Dunaevsky, Y. Raitses, and N. J. Fisch Plasma Physics Laboratory, Princeton University, P.O.Box 451,
More informationCET PHYSICS 2011 VERSION CODE: A 4
dislacement CET PHYSICS 0 VERSION CODE: 4. If C be the caacitance and V be the electric otential, then the dimensional formula of CV is ) M L T ) M 0 L T 0 ) M L T 4) M L T 0 CV Energy The dimentional
More informationIntroduction to Landau s Fermi Liquid Theory
Introduction to Landau s Fermi Liquid Theory Erkki Thuneberg Deartment of hysical sciences University of Oulu 29 1. Introduction The rincial roblem of hysics is to determine how bodies behave when they
More informationHigh spatial resolution distributed sensing in optical fibers by Brillouin gain-profile tracing
High satial resolution distributed sensing in otical fibers by Brillouin gain-rofile tracing Tom Serber, 1,* Avishay Eyal, 1 Moshe Tur, 1 and Luc Thévenaz 2 1 School of Electrical Engineering, Faculty
More informationSession 5: Review of Classical Astrodynamics
Session 5: Review of Classical Astrodynamics In revious lectures we described in detail the rocess to find the otimal secific imulse for a articular situation. Among the mission requirements that serve
More informationNotes on pressure coordinates Robert Lindsay Korty October 1, 2002
Notes on ressure coordinates Robert Lindsay Korty October 1, 2002 Obviously, it makes no difference whether the quasi-geostrohic equations are hrased in height coordinates (where x, y,, t are the indeendent
More informationFeedback-error control
Chater 4 Feedback-error control 4.1 Introduction This chater exlains the feedback-error (FBE) control scheme originally described by Kawato [, 87, 8]. FBE is a widely used neural network based controller
More informationClassical gas (molecules) Phonon gas Number fixed Population depends on frequency of mode and temperature: 1. For each particle. For an N-particle gas
Lecture 14: Thermal conductivity Review: honons as articles In chater 5, we have been considering quantized waves in solids to be articles and this becomes very imortant when we discuss thermal conductivity.
More informationElementary Analysis in Q p
Elementary Analysis in Q Hannah Hutter, May Szedlák, Phili Wirth November 17, 2011 This reort follows very closely the book of Svetlana Katok 1. 1 Sequences and Series In this section we will see some
More informationParabolized stability equation models in turbulent supersonic jets
Parabolized stability equation models in turbulent suersonic jets Daniel Rodríguez,, Aniruddha Sinha, Guillaume A. Brès and Tim Colonius California Institute of Technology, Pasadena, CA Universidad Politécnica
More informationHighlights from the ATLAS experiment
Nuclear Physics A Nuclear Physics A (28) 7 www.elsevier.com/locate/rocedia XXVIIth International Conference on Ultrarelativistic Nucleus-Nucleus Collisions (Quark Matter 28) Highlights from the ALAS exeriment
More informationA M,ETHOD OF MEASURING THE RESISTIVITY AND HALL' COEFFICIENT ON LAMELLAE OF ARBITRARY SHAPE
'. ' 220 HILlS TECHNICAL REVIEW VOLUME 20 A M,ETHOD OF MEASURING THE RESISTIVITY AND HALL' COEFFICIENT ON LAMELLAE OF ARBITRARY SHAE 621.317.331:538.632.083 Resistivity and Hall-coefficient measurements
More informationProduction of Strange Particles in Jets in Heavy-ion Collisions in ALICE
WD'3 Proceedings of Contributed Paers, Part III, 5 57, 23. IBN 978-8-737852-8 MAFYZPRE Production of trange Particles in Jets in Heavy-ion Collisions in ALICE V. učera Charles University in Prague, Faculty
More informationPrototype 16: 3-omega thermal characterization chip (Device C )
Prototype 16: 3-omega thermal characterization chip (Device C ) Lead Partners: Berliner Nanotest und Design GmbH, Germany and VTT-Technical research Centre of Finland This measurement system is suitable
More informationHEAT TRANSFER IN STEADY-PERIODIC FLOWS OVER HEATED MICROWIRES
HEA RANSFER IN SEADY-PERIODIC FLOWS OVER HEAED MICROWIRES S. Yesilyurt, M. Ozcan, G. Goktug Sabanci University, Istanbul, urkey, 34956 ABSRAC Effects of Reynolds number (Re), nondimensional drive frequency
More informationTHE FIRST LAW OF THERMODYNAMICS
THE FIRST LA OF THERMODYNAMIS 9 9 (a) IDENTIFY and SET UP: The ressure is constant and the volume increases (b) = d Figure 9 Since is constant, = d = ( ) The -diagram is sketched in Figure 9 The roblem
More informationThe effect of dynamic bending moments on the ratchetting behavior of stainless steel pressurized piping elbows
International Journal of echanical Engineering and Alications 2014; 2(2): 31-37 Published online ay 30, 2014 (htt://www.scienceublishinggrou.com/j/ijmea) doi: 10.11648/j.ijmea.20140202.12 The effect of
More informationCOMPARISON OF VARIOUS OPTIMIZATION TECHNIQUES FOR DESIGN FIR DIGITAL FILTERS
NCCI 1 -National Conference on Comutational Instrumentation CSIO Chandigarh, INDIA, 19- March 1 COMPARISON OF VARIOUS OPIMIZAION ECHNIQUES FOR DESIGN FIR DIGIAL FILERS Amanjeet Panghal 1, Nitin Mittal,Devender
More information