Identification of model parameters from elastic/elasto-plastic spherical indentation

Size: px
Start display at page:

Download "Identification of model parameters from elastic/elasto-plastic spherical indentation"

Transcription

1 Thomas Niederkofler a, Andreas Jäger a, Roman Lackner b a Institute for Mechanics of Materials and Structures (IMWS), Department of Civil Engineering, Vienna University of Technology, Vienna, Austria b Material-Technology Innsbruck (MTI), Department of Civil Engineering, University of Innsbruck, Innsbruck, Austria Identification of model parameters from elastic/elasto-plastic spherical indentation Spherical indentation is commonly used to study the elastic and visco-elastic response of materials at different length scales. However, depending on the strength properties of the investigated material and the geometric properties, such as sphere radius and penetration depth, plastic material response might occur, making parameter identification from load penetration curves a difficult task. In this paper, the influence of the aforementioned parameters is investigated by means of numerical simulations, considering elastoplastic material response. The numerical results obtained are presented in dimensionless format, finally providing (i) general rules for the specification of test parameters in the case of spherical indentation, on the one hand, and in the case plastic deformation takes place (ii) relations for the determination of plastic model parameters (such as the deviatoric strength) from the loading phase of the indentation test. Keywords: Nanoindentation; Spherical indentation; Elastoplasticity; Parameter identification 1. Motivation Instrumented indentation is a well-known tool for the characterization of materials at various length scales, from the nanometer to the meter range. During indentation tests, a tip with defined shape (see Fig. 1a) penetrates the specimen surface with the applied load P(N) and the penetration h(m) recorded as a function of time. Commonly, each indent consists of a loading, holding, and unloading phase. In the most general case, the material response is characterized by elastic, plastic, and viscous behavior. In general, elastic material parameters are determined from the unloading branch of the load penetration history under the assumption of purely elastic unloading [1]. Parameter identification of materials exhibiting time-dependent behavior (e. g., polymers, bitumen, etc.) requires back calculation of model parameters from the holding phase of the measured penetration history [2 4]. For identification of both elastic and viscous parameters, analytical solutions describing the penetration history are available [5 13] and employed for parameter identification. As regards identification of plastic parameters, on the other hand, no analytical solutions for the penetration history exist. Hence, numerical methods need to be applied for the identification of model parameters from load penetration curves. Such a numerical approach has recently been applied for the special case of conical indenter shapes [14, 15], extracting so-called scaling relations for conical viscoelastic-cohesive indentation from numerical results. In this line, the scaling-relation approach given in [14, 15] is extended towards the case of spherical indenter shapes in this paper. For this purpose, the elastic as well as elasto-plastic material response is studied by means of numerical simulations and compared (for the elastic case) to existing analytical solutions. These analytical solutions for spherical indentation into an elastic halfspace are presented in the following section, including the presentation of the dimensionless format of the parameters used throughout this paper. In Section 3, the employed finite element (FE) model and the chosen simulation parameters (tip radii and material parameters) are given. The results from elastic and elasto-plastic simulations are presented in Section 4. In Section 5, the identification of plastic material param- 926 Int. J. Mat. Res. (formerly Z. Metallkd.) 100 (2009) 7

2 BBasic Fig. 1. Contact between rigid axisymmetric indenter of shape f(q) and an infinite halfspace (P is the applied load, h is the penetration, and a is the contact radius) and load penetration curve and increase in contact radius for indentation of spherical tip into elastic halfspace given by the Hertz and the Sneddon solution (R =1m,E = 1 Pa, m = 0.3). eters from instrumented indentation tests on the basis of the numerical results obtained is discussed. Furthermore, the onset of plastic deformation during elasto-plastic spherical indentation is identified. 2. Analytical solutions for spherical penetration According to the literature, there exist two analytical models to describe the contact between a sphere and an elastic halfspace: 1. In [16], two elastic spheres are considered, assuming that (i) the elastic limit is not passed, (ii) the contact area is significantly smaller than the radii R 1 (m) and R 2 (m) of the spheres, and (iii) only normal stress acts at the contact surface. The relation between the contact force P(N) and the contact deformation h(m) is given by P ¼ KR 0:5 h 1:5 ð1þ where the contact curvature 1=R(m 1 ) and the contact modulus K(Pa) are defined as: 1 R ¼ 1 þ 1 and K ¼ 4 1 m 2 1 þ 1 1 m2 2 ð2þ R 1 R 2 3 E 1 E 2 with R 1 (m), m 1 ( ), E 1 (Pa) and R 2 (m), m 2 ( ), E 2 (Pa) as the radius, Poisson s ratio, and Young s modulus of the two spheres, respectively. For the case of a rigid sphere (R 1 ¼ R, E 1 ¼1) penetrating an elastic halfspace (R 2 ¼1, E 2 ¼ E), the contact modulus K reduces to K ¼ 4 E 3 ð1 m 2 Þ ¼ 4 3 M ð3þ where M is the so-called indentation modulus. Inserting Eq. (3) into Eq. (2) gives the applied load P as a function of penetration h for the Hertz solution as: P ¼ 4 E 3 ð1 m 2 Þ R0:5 h 1:5 ð4þ 2. The so-called Sneddon solution [5] describes the contact between an axisymmetric tip and an infinite elastic halfspace. Here, the tip shape is described by a smooth function f(q) (see Fig. 1a), where q is the radius of the axisymmetric tip. According to [5], the penetration h(m) and the applied load P(N) are given by: Z a f 0 ðqþ dq E q 2 f 0 ðqþ dq h ¼ a pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi and P ¼ 2 pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a 2 q 2 1 m 2 a 2 q 2 q¼0 q¼0 (5) where a(m) is the radius of the projected contact area A c (m 2 ), f 0 ¼ df =dq, and E(Pa) and m( ) are Young s modulus and Poisson s ratio, respectively. In the case of a spherical tip with tip radius R(m), the parameters C 0 ( ) and C 1 (m) of the tip-shape function f ðqþ ¼ 1 qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi C1 2 2C þ 4C 0q 2 p C 1 ð6þ 0 are C 0 = p( ) and C 1 =2Rp(m), yielding p f ðqþ ¼R ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi R 2 q 2 ð7þ Specializing Eq. (5) for the case of a spherical tip shape defined by the tip-shape function given in Eq. (7), one gets hðaþ ¼0:5a log R þ a ð8þ R a and E PðaÞ ¼ 2ð1 m 2 a 2 þ R 2 R þ a log 2aR ð9þ Þ R a According to Eq. (8), the penetration h depends only on geometrical properties, such as the contact radius a and the tip radius R. The applied load P, on the other hand, is a function of a, R, and the mechanical properties of the elastic halfspace, represented by Young s modulus E and Poisson s ratio m. Figure 1b shows a comparison of the load penetration curves obtained from the Hertz and the Sneddon solutions, respectively, for the same radius R and elastic material properties. For small penetrations, both solutions are in good agreement. For increasing penetration, however, the Hertz solution which is only valid for small penetrations leads to an underestimation of the penetration. Z a Int. J. Mat. Res. (formerly Z. Metallkd.) 100 (2009) 7 927

3 BBasic Fig. 2. Sneddon solution for different Poisson s ratios. In case of the spherical elastic indentation, the underlying problem is described by five physical quantities: the applied load P(N), Young s modulus E(N mm 2 ), the radius of the spherical indenter R(mm), the penetration h(mm), and Poisson s ratio m. Considering the Hertz solution (see Eq. (4)) and applying dimensional analysis, the dimensionless variable P is introduced as P p ¼ Eh 1:5 R 0:5 ¼ p m; h ¼ h ð10þ R depending only on two dimensionless parameters, i. e., m and h ¼ h=r. Considering the Hertz solution (Eq. (4)) in Eq. (10), one gets H P ¼ 4 31 ð m 2 ¼ const: ð11þ Þ with H P being independent of h. As regards the Sneddon solution, S P decreases continuously with increasing h (see Fig. 2). Figure 2 shows the influence of Poisson s ratio m on S P ð h Þ, with lower values for S P for decreasing m. When plastic deformation is taken into account, an additional dimensionless variable is introduced, p reading for the von-mises yield criterion f ðrþ ¼ ffiffiffiffiffiffiffi 2J 2 c 0, with J 2 (Pa 2 ) as the second invariant of the stress deviator and c (Pa) as the deviatoric strength: p c ¼ c=e (c is related to the uniaxial strength r Y by r Y ¼ ffiffiffiffiffiffiffi 3=2 c). Accordingly, P depends on three dimensionless parameters, reading P p ¼ Eh 1:5 R 0:5 ¼ p m; h ¼ h R ; c ¼ c ð12þ E 3. Finite element model and considered model parameters Fig. 3. Numerical model and finite element mesh (L =50lm). For the simulation of the indentation process, an axisymmetric model is employed (see Fig. 3), indicating the refinement of the FE mesh in the vicinity of the indenter tip. Numerical simulations are performed considering elastic as well as elasto-plastic material response. The elastic material behavior is described by Young s modulus E(Pa) and Poisson s ratio m( ). In the case of plastic material behavior, the deviatoric strength c(pa) defines the elastic limit (von-mises yield criterion, ideally-plastic behavior). For all simulations, three different radii of the spherical indenter are considered, with R = 1, 2.5 and 5 lm. 4. Presentation of results 4.1. Results from elastic simulations Elastic FE simulations are performed for different Poisson s ratios, Young s moduli, and sphere radii (R = 1, 2.5 and 5 lm). Figure 4a shows the numerical results obtained for m = 0.3. According to Fig. 4a, the numerical results for P are independent of Young s modulus and tip radius, depending only on Poisson s ratio as also observed for the Hertz solution H P. The oscillating shape of the curves results from the discrete nature of the numerical model, with increasing stiffness as a new node of the FE mesh comes into contact with the spherical tip. Comparing the numerical results with the analytical solution, P is underestimated by the Sneddon solution, which is explained by the underlying simplification of zero radial displacement at the contact surface, resulting in a too stiff material sample response (see also [15]). In order to account for the observed deviation between the numerical results and the analytical Sneddon solution, the Sneddon solution is modified by a two-step procedure. In the first step, the numerical results are approximated by: ~ P ¼ k log 10 ð h Þþd ð13þ with k as the slope in the logarithmic scale. Figure 4b shows the approximation function ~ P for m = 0.3 obtained from a best-fit analysis performed within 0 < h < 0:1. The soobtained values for k are given in Table 1 for all considered Poisson s ratios. 928 Int. J. Mat. Res. (formerly Z. Metallkd.) 100 (2009) 7

4 BBasic Table 1. Parameter k for approximation of numerical results and parameter b for determination of the modified Sneddon solution for different Poisson s ratios m. m k b Fig. 4. Spherical indentation (R = 1, 2.5 and 5 lm) into elastic medium (m = 0.3): Numerical results versus Sneddon solution and approximation of numerical results. In the second step, the Sneddon solution is shifted towards the obtained approximation functions, introducing the parameter b, defined by 1 b ¼ ~ P ð h ¼ 0:01Þ S P ð h ¼ 0:01Þ ð14þ The computed values of b for the considered Poisson s ratios are given in Table 1. Finally, b and k are employed for modifying the Sneddon solution, now reading mods P 1 ð h ; mþ ¼ S P ð h; mþþ½bðmþ 1Š S P ð h ¼ 0:01; mþþkðmþ log h 0:01 ð15þ P h = 1%used for determination of the parameter b refers to a rather moderate value for the penetration/radius ratio H/R, corresponding well to the underlying assumption of elastic material response Fig. 5. Spherical indentation (R = 1, 2.5 and 5 lm) into elastic medium (m = 0.3): Modified Sneddon solution compared with numerical results. Figures 5 shows the modified Sneddon solution mods P with the results from the numerical simulations for m = Results from elasto-plastic simulations In the case of spherical indentation into an elasto-plastic material, the amount of plastic deformation depends on (i) the resistance of the material to plastic deformation, i. e., the deviatoric strength c for materials described by the von-mises yield criterion, (ii) the radius of the tip, influencing the stress state under the tip, and (iii) the maximum applied load. Figure 6a shows the numerical results for m = 0.3, three tip radii (R = 5, 2.5 and 1 lm), and different c/e ratios, indicating that: (i) P does not depend on the selected tip radius for a constant c/e ratio and (ii) P does not depend on the values of c and E as long as the respective c/e ratio is the same. In the case plastic deformation occurs, P starts to decrease below the respective value of P of the elastic solution. The oscillating shape of the numerical results, stemming from the discretized nature of the FE discretization, is eliminated by smoothing, giving the numerical results as shown in Fig. 6b. Int. J. Mat. Res. (formerly Z. Metallkd.) 100 (2009) 7 929

5 BBasic Fig. 6. Spherical indentation into elastic-plastic medium (m = 0.3, c/e = , 0.001, 0.002, 0.005, 0.01, 0.015, 0.025, 0.05, 0.075, 0.25, 0.5): Dimensionless plot of numerical simulation results and smoothed numerical results. 5. Discussion and concluding remarks Fig. 7. Identification of plastic model parameters: Experimental results according to [17] and comparison of numerical results (m = 0.3) and experimental results for St35. The identification of elastic material parameters from indentation tests of elasto-plastic materials is commonly performed by using the so-called Oliver and Pharr method [1]. According to Oliver and Pharr, Young s modulus of a material can be determined from the initial slope of the unloading curve of the load penetration history. The exact shape of the indenter (obtained from the calibration procedure) and Poisson s ratio are also required. As regards identification of plastic material parameters, commonly the hardness of the material is employed for characterizing the inelastic behavior, defined as the ratio of the maximum load and the contact area between tip and sample surface. For identification of plastic model parameters (such as, e. g., strength properties of yield criteria) from spherical indentation tests, the numerical results presented in the previous section are used. With known tip shape (tip radius), Poisson s ratio, and Young s modulus, the deviatoric strength of a material can be determined, employing the following procedure: 1. Perform indentation test and record load and penetration continuously during loading and unloading; 2. Determine Young s modulus using the Oliver and Pharr method; 3. Compute P and plot loading path of indentation test in dimensionless form as presented in the previous section; 4. Compare experimental result with results from numerical simulations presented in the previous section, giving access to the c/e ratio of the considered material sample. Finally, the deviatoric strength c is computed, using the c/e ratio and the known Young s modulus. This procedure is illustrated for identification of strength properties of steel (St35). The results from spherical penetration tests on St35 were taken from [17] (see Fig. 7a). Young s modulus E and Poisson s ratio m of this material are MPa and 0.3, respectively. According to [17], the tests are performed using a spherical indenter with a tip radius of 1.25 mm. Figure 7b shows the dimensionless plot of the experimental results together with the results from numerical simulations for m = 0.3. Comparing the numerical results 930 Int. J. Mat. Res. (formerly Z. Metallkd.) 100 (2009) 7

6 BBasic Fig. 8. Spherical indentation: Boundary between elastic and elasto-plastic material response for m = 0.3 and m = 0.0, 0.15, 0.3, Fig. 9. Smoothed numerical results for spherical indentation for different c/e ratios and different Poisson s ratios. Int. J. Mat. Res. (formerly Z. Metallkd.) 100 (2009) 7 931

7 BBasic with the experiment result, the c/e-ratio is found as c/e & , laying within < c/e < , giving a uniaxial strength of p r Y ¼ ffiffiffiffiffiffiffi pffiffiffiffiffiffiffi 3=2 c ¼ E 3=2 c=e pffiffiffiffiffiffiffi ¼ =2 0:0013 ¼ 334 MPa ð16þ This value lies within the range between the yield and ultimate strength of St35, given by r Y ¼ 235 MPa and r u ¼ MPa. The higher value for the identified strength property of 334 MPa is explained by the assumption of ideally-plastic material behavior in the numerical simulations. Thus, the identified strength property represents both the yield and ultimate strength of St35. The extension of the relations for identification of strength properties presented in this paper towards hardening is a topic of ongoing research. In the first part of the loading phase, spherical indentation is characterized by a pure elastic material response. However, with increasing load, plastic deformation develops. The onset of plastic deformation depends on the tip radius as well as the material behavior in terms of Poisson s ratio, Young s modulus, and deviatoric strength. The numerical results presented in the previous section provide the value of h corresponding to the onset of plastic deformation (see Fig. 8a for m = 0.3). Figure 8b gives h corresponding to the onset of plastic deformation as a function of c for different Poisson s ratios. Based on the numerical results and the findings presented in this paper, the following conclusions can be drawn: 1. Depending on the tip shape, the material properties, and the maximum load, spherical indentation is characterized by either pure elastic or elasto-plastic material response. The onset of plastic deformation can be determined using the given relations between the dimensionless parameters h and c defining the boundary line between elastic and elasto-plastic indentation. 2. In case of indentation tests performed in the elastic regime, the presented modified Sneddon solution can be employed for identification of elastic material parameters. This modified analytical solution is based on the numerical simulations taking into account effects neglected by the Sneddon solution, such as radial displacements of points at the contact surface. 3. If the elastic limit is exceeded, the indentation process is characterized by elasto-plastic material behavior. In this case, no analytical solutions, required for identification of plastic model parameters, are available. However, plastic model parameters can be determined using the dimensionless representation of the numerical results presented in this paper. This approach was illustrated for steel St35. The respective functions required for parameter identification are given in Fig. 9 for all considered Poisson s ratios. References [1] W. Oliver, G. Pharr: J. Mater. Res. 7 (1992) [2] L. Cheng, X. Xia, L. Scriven, W. Gerberich: Mech. Mater. 37 (2005) 213. [3] M. Vandamme, F.-J. Ulm: Int. J. Sol. Struct. 43 (2006) [4] A. Jäger, R. Lackner, J. Eberhardsteiner: Mecanica 42 (2007) 293. [5] I. Sneddon: Int. J. Eng. Sci. 3 (1965) 47. [6] E. Lee: Q. Appl. Math. 13 (1955) 183. [7] J. Radok: Q. Appl. Math. 15 (1957) 189. [8] E. Lee, J. Radok: J. Appl. Mech. 27 (1960) 438. [9] S. Hunter: J. Mech. Phys. Sol. 8 (1960) 219. [10] G. Graham: Int. J. Eng. Sci. 3 (1965) 27. [11] G. Graham: Int. J. Eng. Sci. 5 (1967) 495. [12] T. Ting: J. Appl. Mech. 33 (1966) 845. [13] T. Ting: J. Appl. Mech. 35 (1968) 248. [14] Ch. Pichler: Multiscale characterization and modeling of creep and autogeneous shrinkage of early-age cement-based materials. Ph.D. thesis, Vienna University of Technology, Vienna (2007). [15] C. Pichler, R. Lackner, F.-J. Ulm: Int. J. Mater. Res. 99 (2008) 836. [16] H. Hertz: Journal für die reine und angewandte Mathematik 92 (1882) 156. [17] S. Kucharski, Z. Mróz: J. Eng. Mater. Techn. 123 (2001) 245. (Received November 4, 2008; accepted February 4, 2009) Bibliography DOI / Int. J. Mat. Res. (formerly Z. Metallkd.) 100 (2009) 7; page # Carl Hanser Verlag GmbH & Co. KG ISSN Correspondence address Prof. Roman Lackner Material-Technology Innsbruck (MTI) Department of Civil Engineering, University of Innsbruck Technikerstraße 13, A-6020 Innsbruck, Austria Tel.: Fax: Roman.Lackner@uibk.ac.at You will find the article and additional material by entering the document number MK on our website at Int. J. Mat. Res. (formerly Z. Metallkd.) 100 (2009) 7

STUDIES ON NANO-INDENTATION OF POLYMERIC THIN FILMS USING FINITE ELEMENT METHODS

STUDIES ON NANO-INDENTATION OF POLYMERIC THIN FILMS USING FINITE ELEMENT METHODS STUDIES ON NANO-INDENTATION OF POLYMERIC THIN FILMS USING FINITE ELEMENT METHODS Shen Xiaojun, Yi Sung, Lallit Anand Singapore-MIT Alliance E4-04-0, 4 Engineering Drive 3, Singapore 7576 Zeng Kaiyang Institute

More information

Methodology for the evaluation of yield strength and hardening behavior of metallic materials by indentation with spherical tip

Methodology for the evaluation of yield strength and hardening behavior of metallic materials by indentation with spherical tip JOURNAL OF APPLIED PHYSICS VOLUME 94, NUMBER 1 1 JULY 2003 Methodology for the evaluation of yield strength and hardening behavior of metallic materials by indentation with spherical tip Dejun Ma Department

More information

Influence of friction in material characterization in microindentation measurement

Influence of friction in material characterization in microindentation measurement Influence of friction in material characterization in microindentation measurement W.C. Guo a,b,, G. Rauchs c, W.H. Zhang b, J.P. Ponthot a a LTAS. Department of Aerospace & Mechanical Engineering, University

More information

A FINITE ELEMENT STUDY OF ELASTIC-PLASTIC HEMISPHERICAL CONTACT BEHAVIOR AGAINST A RIGID FLAT UNDER VARYING MODULUS OF ELASTICITY AND SPHERE RADIUS

A FINITE ELEMENT STUDY OF ELASTIC-PLASTIC HEMISPHERICAL CONTACT BEHAVIOR AGAINST A RIGID FLAT UNDER VARYING MODULUS OF ELASTICITY AND SPHERE RADIUS Proceedings of the International Conference on Mechanical Engineering 2009 (ICME2009) 26-28 December 2009, Dhaka, Bangladesh ICME09- A FINITE ELEMENT STUDY OF ELASTIC-PLASTIC HEMISPHERICAL CONTACT BEHAVIOR

More information

A Finite Element Study of Elastic-Plastic Hemispherical Contact Behavior against a Rigid Flat under Varying Modulus of Elasticity and Sphere Radius

A Finite Element Study of Elastic-Plastic Hemispherical Contact Behavior against a Rigid Flat under Varying Modulus of Elasticity and Sphere Radius Engineering, 2010, 2, 205-211 doi:10.4236/eng.2010.24030 Published Online April 2010 (http://www. SciRP.org/journal/eng) 205 A Finite Element Study of Elastic-Plastic Hemispherical Contact Behavior against

More information

UNLOADING OF AN ELASTIC-PLASTIC LOADED SPHERICAL CONTACT

UNLOADING OF AN ELASTIC-PLASTIC LOADED SPHERICAL CONTACT 2004 AIMETA International Tribology Conference, September 14-17, 2004, Rome, Italy UNLOADING OF AN ELASTIC-PLASTIC LOADED SPHERICAL CONTACT Yuri KLIGERMAN( ), Yuri Kadin( ), Izhak ETSION( ) Faculty of

More information

Unloading of an elastic plastic loaded spherical contact

Unloading of an elastic plastic loaded spherical contact International Journal of Solids and Structures 42 (2005) 3716 3729 www.elsevier.com/locate/ijsolstr Unloading of an elastic plastic loaded spherical contact I. Etsion *, Y. Kligerman, Y. Kadin Department

More information

EFFECT OF STRAIN HARDENING ON ELASTIC-PLASTIC CONTACT BEHAVIOUR OF A SPHERE AGAINST A RIGID FLAT A FINITE ELEMENT STUDY

EFFECT OF STRAIN HARDENING ON ELASTIC-PLASTIC CONTACT BEHAVIOUR OF A SPHERE AGAINST A RIGID FLAT A FINITE ELEMENT STUDY Proceedings of the International Conference on Mechanical Engineering 2009 (ICME2009) 26-28 December 2009, Dhaka, Bangladesh ICME09- EFFECT OF STRAIN HARDENING ON ELASTIC-PLASTIC CONTACT BEHAVIOUR OF A

More information

Effect of Strain Hardening on Unloading of a Deformable Sphere Loaded against a Rigid Flat A Finite Element Study

Effect of Strain Hardening on Unloading of a Deformable Sphere Loaded against a Rigid Flat A Finite Element Study Effect of Strain Hardening on Unloading of a Deformable Sphere Loaded against a Rigid Flat A Finite Element Study Biplab Chatterjee, Prasanta Sahoo 1 Department of Mechanical Engineering, Jadavpur University

More information

3-D Finite Element Analysis of Instrumented Indentation of Transversely Isotropic Materials

3-D Finite Element Analysis of Instrumented Indentation of Transversely Isotropic Materials 3-D Finite Element Analysis of Instrumented Indentation of Transversely Isotropic Materials Abstract: Talapady S. Bhat and T. A. Venkatesh Department of Material Science and Engineering Stony Brook University,

More information

Modeling Contact between Rigid Sphere and Elastic Layer Bonded to Rigid Substrate

Modeling Contact between Rigid Sphere and Elastic Layer Bonded to Rigid Substrate IEEE TRANSACTIONS ON COMPONENTS AND PACKAGING TECHNOLOGIES, VOL. 24, NO. 2, JUNE 2001 207 Modeling Contact between Rigid Sphere and Elastic Layer Bonded to Rigid Substrate Mirko Stevanović, M. Michael

More information

INTERNATIONAL JOURNAL OF CIVIL AND STRUCTURAL ENGINEERING Volume 4, No 1, 2013

INTERNATIONAL JOURNAL OF CIVIL AND STRUCTURAL ENGINEERING Volume 4, No 1, 2013 INTERNATIONAL JOURNAL OF CIVIL AND STRUCTURAL ENGINEERING Volume 4, No 1, 2013 Copyright by the authors - Licensee IPA- Under Creative Commons license 3.0 Research article ISSN 0976 4399 Nanoindentation

More information

Finite Element Modeling of Nanoindentation on C S H: Effect of Pile up and Contact Friction E. Sarris 1 and G. Constantinides 1,2

Finite Element Modeling of Nanoindentation on C S H: Effect of Pile up and Contact Friction E. Sarris 1 and G. Constantinides 1,2 NICOM 4: 4th International Symposium on Nanotechnology in Construction Finite Element Modeling of Nanoindentation on C S H: Effect of Pile up and Contact Friction E. Sarris 1 and G. Constantinides 1,2

More information

Concrete subjected to combined mechanical and thermal loading: New experimental insight and micromechanical modeling

Concrete subjected to combined mechanical and thermal loading: New experimental insight and micromechanical modeling Concrete subjected to combined mechanical thermal loading: New experimental insight micromechanical modeling Thomas Ring 1, Matthias Zeiml 1,2, Roman Lackner 3 1 Institute for Mechanics of Materials Structures

More information

A novel approach to predict the growth rate of short cracks under multiaxial loadings

A novel approach to predict the growth rate of short cracks under multiaxial loadings A novel approach to predict the growth rate of short cracks under multiaxial loadings F. Brugier 1&2, S. Pommier 1, R. de Moura Pinho 2, C. Mary 2 and D. Soria 2 1 LMT-Cachan, ENS Cachan / CNRS / UPMC

More information

Modeling the dependence of the coefficient of restitution on the impact velocity in elasto-plastic collisions

Modeling the dependence of the coefficient of restitution on the impact velocity in elasto-plastic collisions International Journal of Impact Engineering 27 (2002) 317 341 Modeling the dependence of the coefficient of restitution on the impact velocity in elasto-plastic collisions Xiang Zhang 1, Loc Vu-Quoc* Aerospace

More information

Fine adhesive particles A contact model including viscous damping

Fine adhesive particles A contact model including viscous damping Fine adhesive particles A contact model including viscous damping CHoPS 2012 - Friedrichshafen 7 th International Conference for Conveying and Handling of Particulate Solids Friedrichshafen, 12 th September

More information

Thermal load-induced notch stress intensity factors derived from averaged strain energy density

Thermal load-induced notch stress intensity factors derived from averaged strain energy density Available online at www.sciencedirect.com Draft ScienceDirect Draft Draft Structural Integrity Procedia 00 (2016) 000 000 www.elsevier.com/locate/procedia 21st European Conference on Fracture, ECF21, 20-24

More information

Application of nanoindentation technique to extract properties of thin films through experimental and numerical analysis

Application of nanoindentation technique to extract properties of thin films through experimental and numerical analysis Materials Science-Poland, Vol. 28, No. 3, 2010 Application of nanoindentation technique to extract properties of thin films through experimental and numerical analysis A. WYMYSŁOWSKI 1*, Ł. DOWHAŃ 1, O.

More information

Extraction of Plastic Properties of Aluminum Single Crystal Using Berkovich Indentation

Extraction of Plastic Properties of Aluminum Single Crystal Using Berkovich Indentation Materials Transactions, Vol. 51, No. 11 (2010) pp. 2104 to 2108 #2010 The Japan Institute of Metals EXPRESS REGULAR ARTICLE Extraction of Plastic Properties of Aluminum Single Crystal Using Berkovich Indentation

More information

Determination of the mechanical properties of metallic thin lms and substrates from indentation tests

Determination of the mechanical properties of metallic thin lms and substrates from indentation tests PHILOSOPHICAL MAGAZINE A, 2002, VOL. 82, NO. 10, 2013±2029 Determination of the mechanical properties of metallic thin lms and substrates from indentation tests K. Tunvisut, E. P. Busso, N. P. O Dowdy

More information

Module-4. Mechanical Properties of Metals

Module-4. Mechanical Properties of Metals Module-4 Mechanical Properties of Metals Contents ) Elastic deformation and Plastic deformation ) Interpretation of tensile stress-strain curves 3) Yielding under multi-axial stress, Yield criteria, Macroscopic

More information

Keysight Technologies Instrumented Indentation Testing with the Keysight Nano Indenter G200. Application Note

Keysight Technologies Instrumented Indentation Testing with the Keysight Nano Indenter G200. Application Note Keysight Technologies Instrumented Indentation Testing with the Keysight Nano Indenter G200 Application Note Introduction The scale of materials and machined components continues to decrease with advances

More information

Prediction of the bilinear stress-strain curve of engineering material by nanoindentation test

Prediction of the bilinear stress-strain curve of engineering material by nanoindentation test Prediction of the bilinear stress-strain curve of engineering material by nanoindentation test T.S. Yang, T.H. Fang, C.T. Kawn, G.L. Ke, S.Y. Chang Institute of Mechanical & Electro-Mechanical Engineering,

More information

Nonlinear Finite Element Modeling of Nano- Indentation Group Members: Shuaifang Zhang, Kangning Su. ME 563: Nonlinear Finite Element Analysis.

Nonlinear Finite Element Modeling of Nano- Indentation Group Members: Shuaifang Zhang, Kangning Su. ME 563: Nonlinear Finite Element Analysis. ME 563: Nonlinear Finite Element Analysis Spring 2016 Nonlinear Finite Element Modeling of Nano- Indentation Group Members: Shuaifang Zhang, Kangning Su Department of Mechanical and Nuclear Engineering,

More information

INFLUENCE OF A WELDED PIPE WHIP RESTRAINT ON THE CRITICAL CRACK SIZE IN A 90 BEND

INFLUENCE OF A WELDED PIPE WHIP RESTRAINT ON THE CRITICAL CRACK SIZE IN A 90 BEND 18th International Conference on Structural Mechanics in Reactor Technology (SMiRT 18) Beijing, China, August 7-12, 25 SMiRT18-G8-5 INFLUENCE OF A WELDED PIPE WHIP RESTRAINT ON THE CRITICAL CRACK SIZE

More information

Dynamic Mechanical Analysis (DMA) of Polymers by Oscillatory Indentation

Dynamic Mechanical Analysis (DMA) of Polymers by Oscillatory Indentation Dynamic Mechanical Analysis (DMA) of Polymers by Oscillatory Indentation By Jennifer Hay, Nanomechanics, Inc. Abstract This application note teaches the theory and practice of measuring the complex modulus

More information

Contact Modeling of Rough Surfaces. Robert L. Jackson Mechanical Engineering Department Auburn University

Contact Modeling of Rough Surfaces. Robert L. Jackson Mechanical Engineering Department Auburn University Contact Modeling of Rough Surfaces Robert L. Jackson Mechanical Engineering Department Auburn University Background The modeling of surface asperities on the micro-scale is of great interest to those interested

More information

Final Project: Indentation Simulation Mohak Patel ENGN-2340 Fall 13

Final Project: Indentation Simulation Mohak Patel ENGN-2340 Fall 13 Final Project: Indentation Simulation Mohak Patel ENGN-2340 Fall 13 Aim The project requires a simulation of rigid spherical indenter indenting into a flat block of viscoelastic material. The results from

More information

Experimental Investigation of Fully Plastic Contact of a Sphere Against a Hard Flat

Experimental Investigation of Fully Plastic Contact of a Sphere Against a Hard Flat J. Jamari e-mail: j.jamari@ctw.utwente.nl D. J. Schipper University of Twente, Surface Technology and Tribology, Faculty of Engineering Technology, Drienerloolaan 5, Postbus 17, 7500 AE, Enschede, The

More information

Finite element analysis of indentation experiments J.M. Olaf Fraunhofer-Insitut fur Werkstoffmechanik, Wohlerstr. 11, D-W Freiburg, Germany

Finite element analysis of indentation experiments J.M. Olaf Fraunhofer-Insitut fur Werkstoffmechanik, Wohlerstr. 11, D-W Freiburg, Germany Finite element analysis of indentation experiments J.M. Olaf Fraunhofer-Insitut fur Werkstoffmechanik, Wohlerstr. 11, D-W- 7800 Freiburg, Germany ABSTRACT There are only a few methods suitable for a quantitative

More information

MECHANICAL PROPERTIES OF HYDROGEL USING NANOINDENTATION

MECHANICAL PROPERTIES OF HYDROGEL USING NANOINDENTATION MECHANICAL PROPERTIES OF HYDROGEL USING NANOINDENTATION Prepared by Duanjie Li, PhD & Jorge Ramirez 6 Morgan, Ste156, Irvine CA 9618 P: 949.461.99 F: 949.461.93 nanovea.com Today's standard for tomorrow's

More information

Multiscale modeling of failure in ABS materials

Multiscale modeling of failure in ABS materials Institute of Mechanics Multiscale modeling of failure in ABS materials Martin Helbig, Thomas Seelig 15. International Conference on Deformation, Yield and Fracture of Polymers Kerkrade, April 2012 Institute

More information

Siping Road 1239, , Shanghai, P.R. China

Siping Road 1239, , Shanghai, P.R. China COMPARISON BETWEEN LINEAR AND NON-LINEAR KINEMATIC HARDENING MODELS TO PREDICT THE MULTIAXIAL BAUSCHINGER EFFECT M.A. Meggiolaro 1), J.T.P. Castro 1), H. Wu 2) 1) Department of Mechanical Engineering,

More information

ANALYSIS ON PSEUDO-STEADY INDENTATION CREEP

ANALYSIS ON PSEUDO-STEADY INDENTATION CREEP Acta Mechanica Solida Sinica, Vol. 21, No. 4, August, 2008 ISSN 0894-9166 Published by AMSS Press, Wuhan, China. DOI: 10.1007/s10338-008-0832-3 ANALYSIS ON PSEUDO-STEADY INDENTATION CREEP Hidenari Takagi

More information

Mechanics of Materials

Mechanics of Materials Mechanics of Materials (11) 1 1 ontents lists available at ScienceDirect Mechanics of Materials journal homepage: www.elsevier.com/locate/mechmat A dual conical indentation technique based on FEA solutions

More information

IMPROVED METHOD TO DETERMINE THE HARDNESS AND ELASTIC MODULI USING NANO-INDENTATION

IMPROVED METHOD TO DETERMINE THE HARDNESS AND ELASTIC MODULI USING NANO-INDENTATION KMITL Sci. J. Vol. 5 No. Jan-Jun 005 IMPROVED METHOD TO DETERMINE THE HARDNESS AND ELASTIC MODULI USING NANO-INDENTATION Nurot Panich*, Sun Yong School of Materials Engineering, Nanyang Technological University,

More information

AME COMPUTATIONAL MULTIBODY DYNAMICS. Friction and Contact-Impact

AME COMPUTATIONAL MULTIBODY DYNAMICS. Friction and Contact-Impact 1 Friction AME553 -- COMPUTATIONAL MULTIBODY DYNAMICS Friction and Contact-Impact Friction force may be imposed between contacting bodies to oppose their relative motion. Friction force can be a function

More information

Transactions on Engineering Sciences vol 6, 1994 WIT Press, ISSN

Transactions on Engineering Sciences vol 6, 1994 WIT Press,   ISSN Large strain FE-analyses of localized failure in snow C.H. Liu, G. Meschke, H.A. Mang Institute for Strength of Materials, Technical University of Vienna, A-1040 Karlsplatz 13/202, Vienna, Austria ABSTRACT

More information

Measurement of Bitumen Relaxation Modulus with Instrumented Indentation. Master s Degree Project

Measurement of Bitumen Relaxation Modulus with Instrumented Indentation. Master s Degree Project Measurement of Bitumen Relaxation Modulus with Instrumented Indentation Master s Degree Project Phan Ngoc Trinh Division of Highway and Railway Engineering Department of Transport Science School of Architecture

More information

Burst pressure estimation of reworked nozzle weld on spherical domes

Burst pressure estimation of reworked nozzle weld on spherical domes Indian Journal of Engineering & Materials Science Vol. 21, February 2014, pp. 88-92 Burst pressure estimation of reworked nozzle weld on spherical domes G Jegan Lal a, Jayesh P a & K Thyagarajan b a Cryo

More information

CHARACTERIZATION OF VISCOELASTIC PROPERTIES OF POLYMERIC MATERIALS THROUGH NANOINDENTATION

CHARACTERIZATION OF VISCOELASTIC PROPERTIES OF POLYMERIC MATERIALS THROUGH NANOINDENTATION 3 SEM nnual Conference and Exposition on Experimental and pplied Mechanics, June -4, 3, Charlotte, NC CHRCTERIZTION O VISCOELSTIC PROPERTIES O POLYMERIC MTERILS THROUGH NNOINDENTTION G.M. Odegard, T. Bandorawalla,

More information

Reference material Reference books: Y.C. Fung, "Foundations of Solid Mechanics", Prentice Hall R. Hill, "The mathematical theory of plasticity",

Reference material Reference books: Y.C. Fung, Foundations of Solid Mechanics, Prentice Hall R. Hill, The mathematical theory of plasticity, Reference material Reference books: Y.C. Fung, "Foundations of Solid Mechanics", Prentice Hall R. Hill, "The mathematical theory of plasticity", Oxford University Press, Oxford. J. Lubliner, "Plasticity

More information

SSNV221 Hydrostatic test with a behavior DRUCK_PRAGER linear and parabolic

SSNV221 Hydrostatic test with a behavior DRUCK_PRAGER linear and parabolic Titre : SSNV221 - Essai hydrostatique avec un comportement[...] Date : 08/08/2011 Page : 1/10 SSNV221 Hydrostatic test with a behavior DRUCK_PRAGER linear and parabolic Summary: The case test proposes

More information

ME 2570 MECHANICS OF MATERIALS

ME 2570 MECHANICS OF MATERIALS ME 2570 MECHANICS OF MATERIALS Chapter III. Mechanical Properties of Materials 1 Tension and Compression Test The strength of a material depends on its ability to sustain a load without undue deformation

More information

Elastic-plastic Contact of a Deformable Sphere Against a Rigid Flat for Varying Material Properties Under Full Stick Contact Condition

Elastic-plastic Contact of a Deformable Sphere Against a Rigid Flat for Varying Material Properties Under Full Stick Contact Condition B. CHATTERJEE, P. SAHOO Elastic-plastic Contact of a Deformable Sphere Against a Rigid Flat for Varying Material Properties Under Full Stick Contact Condition RESEARCH The present study considers finite

More information

A simple model for elastic and viscoelastic punch. indentation problems with experimental validation

A simple model for elastic and viscoelastic punch. indentation problems with experimental validation A simple model for elastic and viscoelastic punch indentation problems with experimental validation A. SAMEUR, H. P. YIN, D. DUHAMEL, V. VILKE Université Paris-Est, Institut Navier, LAMI, Ecole Nationale

More information

International Journal of Solids and Structures

International Journal of Solids and Structures International Journal of Solids and Structures 45 (2008) 6018 6033 Contents lists available at ScienceDirect International Journal of Solids and Structures journal homepage: www.elsevier.com/locate/ijsolstr

More information

Optimization of blank dimensions to reduce springback in the flexforming process

Optimization of blank dimensions to reduce springback in the flexforming process Journal of Materials Processing Technology 146 (2004) 28 34 Optimization of blank dimensions to reduce springback in the flexforming process Hariharasudhan Palaniswamy, Gracious Ngaile, Taylan Altan ERC

More information

6 Examples of pneumatic structures and material models for membranes

6 Examples of pneumatic structures and material models for membranes 6 Examples of pneumatic structures and material models for membranes This chapter is divided in two main topics: material models for membranes and static analysis of pneumatic structures. Initially uniaxial

More information

A Laboratory Experiment Using Nanoindentation to Demonstrate the Indentation Size Effect

A Laboratory Experiment Using Nanoindentation to Demonstrate the Indentation Size Effect Bucknell University Bucknell Digital Commons Faculty Journal Articles Faculty Scholarship 2013 A Laboratory Experiment Using Nanoindentation to Demonstrate the Indentation Size Effect Wendelin Wright Bucknell

More information

Determination of Mechanical Properties of Elastomers Using Instrumented Indentation

Determination of Mechanical Properties of Elastomers Using Instrumented Indentation Determination of Mechanical Properties of Elastomers Using Instrumented Indentation, Antonios E. Giannakopoulos and Dimitrios Bourntenas University of Thessaly, Department of Civil Engineering, Volos 38334,

More information

Supplementary Information: Nanoscale heterogeneity promotes energy dissipation in bone

Supplementary Information: Nanoscale heterogeneity promotes energy dissipation in bone Supplementary Information: Nanoscale heterogeneity promotes energy dissipation in bone KUANGSHIN TAI, * MING DAO, * SUBRA SURESH,, AHMET PALAZOGLU, & AND CHRISTINE ORTIZ Department of Materials Science

More information

COMPUTATIONAL MODELING OF THE FORWARD AND REVERSE PROBLEMS IN INSTRUMENTED SHARP INDENTATION

COMPUTATIONAL MODELING OF THE FORWARD AND REVERSE PROBLEMS IN INSTRUMENTED SHARP INDENTATION Acta mater. 49 (2001) 3899 3918 www.elsevier.com/locate/actamat COMPUTATIONAL MODELING OF THE FORWARD AND REVERSE PROBLEMS IN INSTRUMENTED SHARP INDENTATION M. DAO, N. CHOLLACOOP, K. J. VAN VLIET, T. A.

More information

Abstract. 1 Introduction

Abstract. 1 Introduction Elasto-plastic contact of rough surfaces K. Willner Institute A of Mechanics, University of Stuttgart, D-70550 Stuttgart, Germany E-mail: willner@mecha. uni-stuttgart. de Abstract If two rough surfaces

More information

Lecture #7: Basic Notions of Fracture Mechanics Ductile Fracture

Lecture #7: Basic Notions of Fracture Mechanics Ductile Fracture Lecture #7: Basic Notions of Fracture Mechanics Ductile Fracture by Dirk Mohr ETH Zurich, Department of Mechanical and Process Engineering, Chair of Computational Modeling of Materials in Manufacturing

More information

An alternative design method for the double-layer combined die using autofrettage theory

An alternative design method for the double-layer combined die using autofrettage theory https://doi.org/10.5194/ms-8-267-2017 Author(s) 2017. This work is distributed under the Creative Commons Attribution.0 License. An alternative design method for the double-layer combined die using autofrettage

More information

A Finite Element Study of the Residual Stress and Deformation in Hemispherical Contacts

A Finite Element Study of the Residual Stress and Deformation in Hemispherical Contacts obert Jackson 1 Mem. ASME e-mail: robert.jackson@eng.auburn.edu Itti Chusoipin Itzhak Green Fellow, ASME George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA

More information

A novel technique of friction and material property measurement by tip test in cold forging

A novel technique of friction and material property measurement by tip test in cold forging A novel technique of friction and material property measurement by tip test in cold forging Y T Im*, S H Kang, and J S Cheon Department of Mechanical Engineering, Korea Advanced Institute of Science and

More information

University of Sheffield The development of finite elements for 3D structural analysis in fire

University of Sheffield The development of finite elements for 3D structural analysis in fire The development of finite elements for 3D structural analysis in fire Chaoming Yu, I. W. Burgess, Z. Huang, R. J. Plank Department of Civil and Structural Engineering StiFF 05/09/2006 3D composite structures

More information

Computational Inelasticity FHLN05. Assignment A non-linear elasto-plastic problem

Computational Inelasticity FHLN05. Assignment A non-linear elasto-plastic problem Computational Inelasticity FHLN05 Assignment 2018 A non-linear elasto-plastic problem General instructions A written report should be submitted to the Division of Solid Mechanics no later than November

More information

Nanoindentation. M. R. VanLandingham, Review of instrumented indentation, J. Res. Natl. Inst. Stand. Technol. 108, (2003).

Nanoindentation. M. R. VanLandingham, Review of instrumented indentation, J. Res. Natl. Inst. Stand. Technol. 108, (2003). Nanoindentation References Nanoindentation, nd Ed., Antony C. Fiscer-Cripps, Springer, 010. Introduction to Contact Mecanics, nd Ed., Antony C. Fiscer-Cripps, Springer, 007. Contact Mecanics, Kennet L.

More information

The plastic behaviour of silicon subjected to micro-indentation

The plastic behaviour of silicon subjected to micro-indentation JOURNAL OF MATERIALS SCIENCE 31 (1996) 5671-5676 The plastic behaviour of silicon subjected to micro-indentation L. ZHANG, M. MAHDI Centre for Advanced Materials Technology, Department of Mechanical and

More information

Effects of TGO Roughness on Indentation Response of Thermal Barrier Coatings

Effects of TGO Roughness on Indentation Response of Thermal Barrier Coatings Copyright 2010 Tech Science Press CMC, vol.17, no.1, pp.41-57, 2010 Effects of Roughness on Indentation Response of Thermal Barrier Coatings Taotao Hu 1 and Shengping Shen 1,2 Abstract: In this paper,

More information

Determining the Elastic Modulus and Hardness of an Ultrathin Film on a Substrate Using Nanoindentation

Determining the Elastic Modulus and Hardness of an Ultrathin Film on a Substrate Using Nanoindentation Determining the Elastic Modulus and Hardness of an Ultrathin Film on a Substrate Using Nanoindentation The Harvard community has made this article openly available. Please share how this access benefits

More information

MODELING OF ELASTO-PLASTIC MATERIALS IN FINITE ELEMENT METHOD

MODELING OF ELASTO-PLASTIC MATERIALS IN FINITE ELEMENT METHOD MODELING OF ELASTO-PLASTIC MATERIALS IN FINITE ELEMENT METHOD Andrzej Skrzat, Rzeszow University of Technology, Powst. Warszawy 8, Rzeszow, Poland Abstract: User-defined material models which can be used

More information

Non-linear and time-dependent material models in Mentat & MARC. Tutorial with Background and Exercises

Non-linear and time-dependent material models in Mentat & MARC. Tutorial with Background and Exercises Non-linear and time-dependent material models in Mentat & MARC Tutorial with Background and Exercises Eindhoven University of Technology Department of Mechanical Engineering Piet Schreurs July 7, 2009

More information

Lecture #2: Split Hopkinson Bar Systems

Lecture #2: Split Hopkinson Bar Systems Lecture #2: Split Hopkinson Bar Systems by Dirk Mohr ETH Zurich, Department of Mechanical and Process Engineering, Chair of Computational Modeling of Materials in Manufacturing 2015 1 1 1 Uniaxial Compression

More information

Three-Dimensional Failure Criteria Based on the Hoek Brown Criterion

Three-Dimensional Failure Criteria Based on the Hoek Brown Criterion Rock Mech Rock Eng () 45:989 99 DOI.7/s6--77- ISRM SUGGESTED METHOD Three-Dimensional Failure Criteria Based on the Hoek Brown Criterion Stephen Priest Published online: 8 July Ó Springer-Verlag List of

More information

FINITE ELEMENT ANALYSIS OF IMPACT AND PENETRATION OF POLYCARBONATE PLATE BY A RIGID SPHERICAL PROJECTILE

FINITE ELEMENT ANALYSIS OF IMPACT AND PENETRATION OF POLYCARBONATE PLATE BY A RIGID SPHERICAL PROJECTILE FINITE ELEMENT ANALYSIS OF IMPACT AND PENETRATION OF POLYCARBONATE PLATE BY A RIGID SPHERICAL PROJECTILE C.T. Tsai Department of Mechanical Engineering Florida Atlantic University Boca Raton, FL 33431,

More information

Numerical simulation of delamination onset and growth in laminated composites

Numerical simulation of delamination onset and growth in laminated composites Numerical simulation of delamination onset and growth in laminated composites G. Wimmer, C. Schuecker, H.E. Pettermann Austrian Aeronautics Research (AAR) / Network for Materials and Engineering at the

More information

Example-3. Title. Description. Cylindrical Hole in an Infinite Mohr-Coulomb Medium

Example-3. Title. Description. Cylindrical Hole in an Infinite Mohr-Coulomb Medium Example-3 Title Cylindrical Hole in an Infinite Mohr-Coulomb Medium Description The problem concerns the determination of stresses and displacements for the case of a cylindrical hole in an infinite elasto-plastic

More information

Stresses Analysis of Petroleum Pipe Finite Element under Internal Pressure

Stresses Analysis of Petroleum Pipe Finite Element under Internal Pressure ISSN : 48-96, Vol. 6, Issue 8, ( Part -4 August 06, pp.3-38 RESEARCH ARTICLE Stresses Analysis of Petroleum Pipe Finite Element under Internal Pressure Dr.Ragbe.M.Abdusslam Eng. Khaled.S.Bagar ABSTRACT

More information

1.033/1.57 Q#2: Elasticity Bounds Conical Indentation Test

1.033/1.57 Q#2: Elasticity Bounds Conical Indentation Test 1.033/1.57 Q#: Elasticity Bounds Conical Indentation Test November 14, 003 MIT 1.033/1.57 Fall 003 Instructor: Franz-Josef UM Instrumented nano-indentation is a new technique in materials science and engineering

More information

Evaluation of hyperelastic material properties based on instrumented indentation

Evaluation of hyperelastic material properties based on instrumented indentation Surface and Contact Mechanics including Tribology XII 53 Evaluation of hyperelastic material properties based on instrumented indentation V. I. Zafiropoulou & A. E. Giannaopoulos Laboratory of Strength

More information

Computational Inelasticity FHLN05. Assignment A non-linear elasto-plastic problem

Computational Inelasticity FHLN05. Assignment A non-linear elasto-plastic problem Computational Inelasticity FHLN05 Assignment 2017 A non-linear elasto-plastic problem General instructions A written report should be submitted to the Division of Solid Mechanics no later than October

More information

INVERSE METHOD FOR FLOW STRESS PARAMETERS IDENTIFICATION OF TUBE BULGE HYDROFORMING CONSIDERING ANISOTROPY

INVERSE METHOD FOR FLOW STRESS PARAMETERS IDENTIFICATION OF TUBE BULGE HYDROFORMING CONSIDERING ANISOTROPY 7 th EUROMECH Solid Mechanics Conference J. Ambrósio et.al. (eds.) Lisbon, Portugal, September 7-11, 2009 INVERSE METHOD FOR FLOW STRESS PARAMETERS IDENTIFICATION OF TUBE BULGE HYDROFORMING CONSIDERING

More information

TIME-DEPENDENT BEHAVIOR OF PILE UNDER LATERAL LOAD USING THE BOUNDING SURFACE MODEL

TIME-DEPENDENT BEHAVIOR OF PILE UNDER LATERAL LOAD USING THE BOUNDING SURFACE MODEL TIME-DEPENDENT BEHAVIOR OF PILE UNDER LATERAL LOAD USING THE BOUNDING SURFACE MODEL Qassun S. Mohammed Shafiqu and Maarib M. Ahmed Al-Sammaraey Department of Civil Engineering, Nahrain University, Iraq

More information

Influence of impact velocity on transition time for V-notched Charpy specimen*

Influence of impact velocity on transition time for V-notched Charpy specimen* [ 溶接学会論文集第 35 巻第 2 号 p. 80s-84s (2017)] Influence of impact velocity on transition time for V-notched Charpy specimen* by Yasuhito Takashima** and Fumiyoshi Minami** This study investigated the influence

More information

Experimental investigation on monotonic performance of steel curved knee braces for weld-free beam-to-column connections

Experimental investigation on monotonic performance of steel curved knee braces for weld-free beam-to-column connections Experimental investigation on monotonic performance of steel curved knee braces for weld-free beam-to-column connections *Zeyu Zhou 1) Bo Ye 2) and Yiyi Chen 3) 1), 2), 3) State Key Laboratory of Disaster

More information

Introduction to Engineering Materials ENGR2000. Dr. Coates

Introduction to Engineering Materials ENGR2000. Dr. Coates Introduction to Engineering Materials ENGR2 Chapter 6: Mechanical Properties of Metals Dr. Coates 6.2 Concepts of Stress and Strain tension compression shear torsion Tension Tests The specimen is deformed

More information

Discrete Element Modelling of a Reinforced Concrete Structure

Discrete Element Modelling of a Reinforced Concrete Structure Discrete Element Modelling of a Reinforced Concrete Structure S. Hentz, L. Daudeville, F.-V. Donzé Laboratoire Sols, Solides, Structures, Domaine Universitaire, BP 38041 Grenoble Cedex 9 France sebastian.hentz@inpg.fr

More information

Session 15: Measuring Substrate-Independent Young s Modulus of Thin Films

Session 15: Measuring Substrate-Independent Young s Modulus of Thin Films Session 15: Measuring Substrate-Independent Young s Modulus of Thin Films Jennifer Hay Factory Application Engineer Nano-Scale Sciences Division Agilent Technologies jenny.hay@agilent.com To view previous

More information

Mat. Res. Soc. Symp. Proc. Vol Materials Research Society

Mat. Res. Soc. Symp. Proc. Vol Materials Research Society Mat. Res. Soc. Symp. Proc. Vol. 738 2003 Materials Research Society G7.26.1 Determination of the Plastic Behavior of Low Thermal Expansion Glass at the Nanometer Scale Richard Tejeda, 1 Roxann Engelstad,

More information

Nonlinear FE Analysis of Reinforced Concrete Structures Using a Tresca-Type Yield Surface

Nonlinear FE Analysis of Reinforced Concrete Structures Using a Tresca-Type Yield Surface Transaction A: Civil Engineering Vol. 16, No. 6, pp. 512{519 c Sharif University of Technology, December 2009 Research Note Nonlinear FE Analysis of Reinforced Concrete Structures Using a Tresca-Type Yield

More information

The Effect of Coefficient of Restitution for Two Collision Models

The Effect of Coefficient of Restitution for Two Collision Models The Effect of Coefficient of Restitution for Two Collision Models ALACI STELIAN 1, FILOTE CONSTANTIN 2, CIORNEI FLORINA-CARMEN 1 1 Mechanics and Technologies Department 2 The Computers, Electronics and

More information

The effect of plasticity in crumpling of thin sheets: Supplementary Information

The effect of plasticity in crumpling of thin sheets: Supplementary Information The effect of plasticity in crumpling of thin sheets: Supplementary Information T. Tallinen, J. A. Åström and J. Timonen Video S1. The video shows crumpling of an elastic sheet with a width to thickness

More information

Stress Analysis Report

Stress Analysis Report Stress Analysis Report Analyzed File: Majakkarunko.iam Autodesk Inventor Version: 2013 SP2 (Build 170200200, 200) Creation Date: 29.5.2013, 7:01 Simulation Author: NJu Summary: Project Info (iproperties)

More information

Discrete Element Study of Aggregate Damage during Asphalt Compaction

Discrete Element Study of Aggregate Damage during Asphalt Compaction 0 0 0 0 Discrete Element Study of Aggregate Damage during Asphalt Compaction Erik Olsson, Denis Jelagin, Manfred Partl ( KTH Royal Institute of Technology, Department of Civil and Architectural Engineering,

More information

Modelling the behaviour of plastics for design under impact

Modelling the behaviour of plastics for design under impact Modelling the behaviour of plastics for design under impact G. Dean and L. Crocker MPP IAG Meeting 6 October 24 Land Rover door trim Loading stages and selected regions Project MPP7.9 Main tasks Tests

More information

EFFECT OF PILE-UP ON THE MECHANICAL CHARACTERISTICS OF STEEL WITH DIFFERENT STRAIN HISTORY BY DEPTH SENSING INDENTATION

EFFECT OF PILE-UP ON THE MECHANICAL CHARACTERISTICS OF STEEL WITH DIFFERENT STRAIN HISTORY BY DEPTH SENSING INDENTATION EFFECT OF PILE-UP ON THE MECHANICAL CHARACTERISTICS OF STEEL WITH DIFFERENT STRAIN HISTORY BY DEPTH SENSING INDENTATION Peter BURIK 1,a, Ladislav PEŠEK 2,b, Lukáš VOLESKÝ 1,c 1 Technical University of

More information

Back Calculation of Rock Mass Modulus using Finite Element Code (COMSOL)

Back Calculation of Rock Mass Modulus using Finite Element Code (COMSOL) Back Calculation of Rock Mass Modulus using Finite Element Code (COMSOL) Amirreza Ghasemi 1. Introduction Deformability is recognized as one of the most important parameters governing the behavior of rock

More information

Moment redistribution of continuous composite I-girders with high strength steel

Moment redistribution of continuous composite I-girders with high strength steel Moment redistribution of continuous composite I-girders with high strength steel * Hyun Sung Joo, 1) Jiho Moon, 2) Ik-Hyun sung, 3) Hak-Eun Lee 4) 1), 2), 4) School of Civil, Environmental and Architectural

More information

SEMM Mechanics PhD Preliminary Exam Spring Consider a two-dimensional rigid motion, whose displacement field is given by

SEMM Mechanics PhD Preliminary Exam Spring Consider a two-dimensional rigid motion, whose displacement field is given by SEMM Mechanics PhD Preliminary Exam Spring 2014 1. Consider a two-dimensional rigid motion, whose displacement field is given by u(x) = [cos(β)x 1 + sin(β)x 2 X 1 ]e 1 + [ sin(β)x 1 + cos(β)x 2 X 2 ]e

More information

Performance and Control of the Agilent Nano Indenter DCM

Performance and Control of the Agilent Nano Indenter DCM Performance and Control of the Agilent Nano Indenter DCM Application Note Introduction With new materials and material applications come new test challenges. As these new challenges emerge in materials

More information

Dynamics of cell wall elasticity pattern shapes the cell during yeast mating morphogenesis.

Dynamics of cell wall elasticity pattern shapes the cell during yeast mating morphogenesis. Dynamics of cell wall elasticity pattern shapes the cell during yeast mating morphogenesis. Björn Goldenbogen 1, Wolfgang Giese 1, Marie Hemmen 1, Jannis Uhlendorf 1, Andreas Herrmann 2, Edda Klipp 1 1.

More information

Constitutive models: Incremental plasticity Drücker s postulate

Constitutive models: Incremental plasticity Drücker s postulate Constitutive models: Incremental plasticity Drücker s postulate if consistency condition associated plastic law, associated plasticity - plastic flow law associated with the limit (loading) surface Prager

More information

Plane Strain Test for Metal Sheet Characterization

Plane Strain Test for Metal Sheet Characterization Plane Strain Test for Metal Sheet Characterization Paulo Flores 1, Felix Bonnet 2 and Anne-Marie Habraken 3 1 DIM, University of Concepción, Edmundo Larenas 270, Concepción, Chile 2 ENS - Cachan, Avenue

More information

Measurement of ultra-thin film fracture by nanoindentation:

Measurement of ultra-thin film fracture by nanoindentation: Graduate Theses and Dissertations Iowa State University Capstones, Theses and Dissertations 2011 Measurement of ultra-thin film fracture by nanoindentation: a numerical study Benjamin A. Burke Iowa State

More information

An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments

An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments W. C. Oliver Metals and Ceramics Division, Oak Ridge National Laboratory,

More information