X. Assembling the Pieces
|
|
- Darrell Carpenter
- 5 years ago
- Views:
Transcription
1 X. Assembling the Pieces 179 Introduction Our goal all along has been to gain an understanding of nuclear reactors. As we ve noted many times, this requires knowledge of how neutrons are produced and lost. We ve also noted that production and loss rates depend on a multitude of factors, most of which we have discussed in some detail. Perhaps the most basic thing we d like to know about any given reactor is its criticality: is it subcritical, supercritical, or critical? The multiplication factor, k eff, tells us the answer. In Chapter III we developed a 6-factor formula for k eff, and in later chapters we learned that k eff is an eigenvalue of the [Loss] 1 [Production] operator. If we accept the diffusion approximation, this means k eff is an eigenvalue of a differential (or integro-differential) equation. We have now developed solutions of our differential and integro-differential equations, using the diffusion approximation and sometimes using further approximations (all of which are accurate for large homogeneous reactors with lots more moderator than fuel). These solutions now enable us to calculate each of the six factors in the six-factor formula for k eff. We also found, in Chapter VII of these notes, solutions for how neutrons distribute themselves spatially in a bare homogeneous reactor. We now know this for basic shapes such as spheres, cylinders, and rectangular parallelepipeds. In Chapter VIII we learned how neutrons distribute themselves in energy as they slow to thermal energies in infinite reactors, discovering that the dominant behavior is a 1/E distribution in the slowing-down range. We found that absorption perturbs this distribution, causing downward spikes at resonances and a lowering of the flux just below each resonance (compared to the value it would have had without the resonance). We developed approximate expressions for P FNL and p that are accurate for dilute concentrations of fuel in moderators and for large reactors. In Chapter IX we found that neutrons in the thermal range tend toward a Maxwellian distribution in energy. We saw that absorption can perturb this distribution fairly significantly, but that the perturbed distribution looks a lot like a Maxwellian at a higher temperature, which we call the neutron temperature. We also discovered that for 1/v absorbers, which include all light nuclides, it is very easy to compute thermal absorption rates, and that for non-1/v absorbers it is easy to get approximate absorption (and fission) rates by using a non-1/v factor. We also found relationships between 2200-m/s cross sections and thermal cross sections. In this chapter we put this all together and show step by step how to use it to estimate the multiplication factor of a bare homogeneous reactor. We provide tables of needed data (such as thermal diffusion length and age to thermal for various moderators). We also show that we can calculate any reaction rate in any part of the reactor, because we know the spatial and energy distribution of the neutrons.
2 Multiplication Factor of Bare Homogeneous Reactor 180 For the remainder of this chapter let us agree that k is the multiplication factor of the reactor. That is, we drop the eff subscript. We are not concerned in this chapter with any of the other (smaller) k-eigenvalues, so there should be no confusion. The six-factor formula says k = P FNL εpp TNL η T f (1) In Chapters III and VIII we noted that we could write an expression without the fast-fission factor, ε: k = P FNL p P TNL f η T + P FNL (1 p) u F η F. (2) In Chapters VII and VIII we obtained expressions for P TNL, (f η T,) and (u F η F ): (3) Note that resonance integrals in the second term play exactly the same role as the thermal cross sections in the first term. Our goal in this section is to review how to estimate each term in this equation using what we have learned throughout the course. Let s do it. Fast Non-Leakage Probability In Chapter VIII we agreed to use P FNL (4) But where do we find the age to thermal, τ th? This quantity is tabulated for different moderators. Here we reproduce data from a table given in the Lamarsh text. Table: Approximate Ages (in cm 2 ) of Fission Neutrons to Thermal Energies. Also approximate average logarithmic energy decrements and potential scattering cross sections. Moderator Approximate τ th [cm 2 ] σ p [barns] H 2 O D 2 O Be Graphite
3 181 Based in part on data given in L. S. Kothari and V. P. Duggal, Scattering of Thermal Neutrons from Solids and Their Thermalization Near Equilibrium, Advances in Nuclear Science and Technology, Vol. 2. New York: Academic Press, What about a mixture of fuel with one of these moderators? We noted in Ch. VIII that an approximation for age to thermal is. (5) If the mixture is dilute (lots more moderator atoms than fuel atoms), then only at resonance energies will the fuel s presence significantly change the cross sections. These are very narrow ranges compared to the full range of integration. In these ranges the cross sections will be higher than the moderator-only value, and thus in these tiny ranges the contribution to τ th will decrease. We conclude that: In a dilute mixture of the age to thermal is only slightly Thus, in our calculations of large reactors with dilute homogeneous mixtures, Resonance-Escape Probability In Chapter VIII we agreed to use we will use the age to thermal for the moderator. p (6) Here Σ p is the potential scattering cross section of the moderator. If you explore how we got Eq. (6) you will see that Σ p is the scattering cross section evaluated at energies where most of the resonance absorption is taking place, which means from around an ev to a few kev. Resonance Integrals Where do we find the resonance integrals for the absorbing nuclides? If we are in the dilute limit (lots more moderator atoms than fuel atoms), we can get them from the chart of the nuclides. The table below provides values for a few interesting nuclides, and it includes the resonance integral for fission as well, which is needed in the expression for k. Table: Infinitely-Dilute Resonance Integrals. (From Nuclide Resonance Integrals (barns) Capture + Fission Fission U U
4 182 Neutrons Released Per Fission Nuclide Resonance Integrals (barns) Capture + Fission Fission Pu Pu Fe (natural) Zr (natural) O H H-2 (D) H 2 O ( ) 0 D 2 O ( ) 0 Experiments and theory agree that a particular fission event may release 0 or 1 or 2 or 3 or 4 or... neutrons. In reactor analysis we are rarely interested in how many fissions release 0, how many release 1, etc.; all we usually care about is how many are released on average from fissions of a given nuclide, caused by the absorption of neutrons of a given energy. Experiments find that this value fits a very simple formula over wide ranges of incident neutron energy: where and ν 0 and a are constants for a given nuclide and a given range of E, E = energy of the neutron that caused the fission. (8) A table of these constants is given below for various interesting nuclei, sometimes in two energy ranges to accurately fit the measured data. The Constants, v 0 and a, for Eq. (7) Nuclide v 0 = ν th a, [MeV -1 ] Energy range Th all E E 1 MeV U E > 1 MeV E 1 MeV U E > 1 MeV U all E E 1 MeV Pu E > 1 MeV From G. R. Keepin, Physics of Nuclear Kinetics, Reading, Mass.: Addison-Wesley, (7)
5 183 Note that this function varies so slowly in energy that the correct value to use for thermal neutrons is Note in particular that this is 2.43 for U-235. You should remember this number! What about ν f, the average number of neutrons released per fission caused by a non-thermal (fast) neutron? In a thermal reactor, recall that most non-thermal fissions occur in resonances the slowing-down energy range, where the flux is roughly proportional to 1/E. Because the resonance range for the important fissile and fissionable nuclides is roughly from 1 ev to a few kev, and because of the 1/E flux, a reasonable average to use for ν f would be the ν value evaluated at 100 ev or so. This would give ν f = ν 0 + ( MeV)a, (10) which gives. (11) Results are similar for other nuclides: In a thermal reactor, we can use ν f = ν th. (9) Thermal Non-Leakage Probability We now have everything except the thermal-neutron term in our equation for k. This term is:. (12) Here we see the thermal non-leakage probability that we have identified before:. (13) We can evaluate this term if we know L th, the thermal diffusion length. We recall its definition and rearrange that definition: (14) So we begin with the (square of the) diffusion length for the moderator and now examine the two multiplicative correction factors. An example will help clarify the validity of the approximations we are about to propose. Let us keep in mind the example of a mixture of U-235 and H 2 O, with 1 U-235 atom per 100 H 2 O molecules. Let us first consider the absorption ratio:
6 184 = (15) Obviously we cannot ignore a factor this far from 1: We must correct L th for absorption by fuel atoms! (Note that even if the U/water ratio had been 1/1000, this correction would still be around ½.) Now consider the transport-cross-section ratio. To get an estimate of the magnitude of this ratio, we shall look at the ratio of total cross sections, which is almost the same as the ratio of the transport cross sections. We found above that the temperature and sqrt(π)/2 ratios divide out of our cross-section ratios, so here we will jump straight to 2200-m/s values. We note that the 2200-m/s scattering cross section in U-235 is around 15 b, whereas it is around 100 b for H 2 O. Thus: = (16) This is close enough to unity that we can ignore it, especially since it is going to be multiplied by the small number B g 2 and added to unity (see expression for P TNL ). We conclude that for reasonably dilute mixtures of fuel and moderator, we can use: (17) Note that the mixture s diffusion length is always smaller than the moderator s. We need a table of diffusion lengths for common moderators. We take it from Lamarsh: Thermal Neutron Diffusion Parameters of Common Moderators at 20 C Moderator Density (g/cm 3 ) D th (cm) Σ a,th (cm -1 ) L th 2 (cm 2 ) L th (cm) H 2 O D 2 O x x Be x BeO x Graphite x
7 185 Based on Reactor Physics Constants, U.S. Atomic Energy Commission Report ANL 5800, 2nd ed., 1963, Section 3.3. The diffusion properties of D 2 O are sensitive to the amount of H 2 O present. Graphite often contains impurities that affect its diffusion properties; the values given here are for highly-purified graphite. As the note following the table indicates, for materials with teeny tiny absorption cross sections (like graphite or heavy water), the addition of an absorber has a dramatic effect on the diffusion properties. You can see this from our Eq. (17) above we developed this to correct for the presence of fuel, but it is equally valid to correct for the presence of an impurity. In our problems, this won t make any difference unless the impurity s macroscopic absorption cross section is comparable to the fuel s. This is exceedingly unlikely! So in our problems we shall assume that absorption in fuel dominates absorption in impurities, and we will stick with Eq. (17). The Remaining Term The only term we have not addressed is a pretty simple one: = (18) Here we have noted that the temperature and sqrt(π) factors divide out. Given a mixture of an arbitrary number of moderating and fissioning nuclides, our expression becomes. (19) Example: k of Uranium + D 2 O Consider a mixture with Q uranium atoms per D 2 O molecule. Assume a neutron temperature of 100 C. Suppose the U is entirely U-238 and U-235, with W U-235 atoms per total uranium atom. Find k of this mixture as a function of Q and W. Using a spreadsheet, plot this for a few interesting values of W. We begin with our k equation, Eq. (3), with the non-leakage probabilities set to 1. This is:. (20) We begin with expression for p, Eq. (6), and start filling in data: p
8 186 From our table of ages etc., we find: and. From our table of resonance integrals we find: and. So we have: p (21) We plot this below for natural uranium (W = 0.007) and a typical value of enrichment (W = 0.035) as a function of Q. As you can see, the enrichment doesn t make much difference in p, because for low enrichments p is dominated by absorption in U p (W=.007) p (W=0.035) Figure: Resonance-escape probability as a function of Q = U/D 2 O ratio for two different values of W = U-235/(total U) ratio. Next we recognize that ν f ν th = Now the resonance-integral ratio:
9 187 = (22) Note that we have ignored the resonance integral in D 2 O. From our table of resonance integrals we see that the resonance integral in D and O are b and b, respectively. These values are too tiny to make a significant contribution, so we don t worry about them. Now the thermal ratio:. Let s get numbers for these ratios under the assumption of natural uranium (W=0.007):. With these, and with W=0.007 plugged into our expression for p, we have: (23) A plot:
10 k Q Figure: Infinite-medium multiplication factor as a function of U/D 2 O ratio for natural uranium. Example 2: k of (Uranium + D 2 O) cylinder Consider a finite cylindrical reactor composed of natural uranium mixed with D 2 O. Again assume a neutron temperature of 100 C, and assume a density of 1.1 g/cm 3. Consider a bare cylinder of this material of radius 2 meters and height 3 meters, and assume the near-optimal ratio of 1 uranium atom for every 500 D2O molecules (Q = 0.002). What is the multiplication factor? From the previous section we have k = Now we need the non-leakage probabilities. For each of them we will need the geometric buckling, so let s get it: = For the fast non-leakage probability we will need the age to thermal. The age to thermal in D 2 O is approximately, according to our table above. We will also need the square of the thermal diffusion length. Our formula for this is Eq. (17) above:. (24)
11 189 According to our table, The other term is: = cm 2. (That s pretty big!) = (25) Putting this together, we have: P FNL = = P TNL = = (26) Note that the huge diffusion length in D 2 O (which is the result of having almost no absorption in D2O) causes lots of thermal neutrons to leak out! This makes the reactor quite subcritical, as we see when we insert our numbers: (27) When we crunch the numbers we obtain k (28) We conclude that while it is possible to make a critical reactor out of a homogeneous mixture of natural uranium and heavy water, the reactor must be really large! This is why CANDU reactors (Canadian reactors fueled by natural uranium and moderated by heavy water) are much larger than light-water reactors. Another Trick You now should see how to estimate the multiplication factor for a bare homogeneous reactor if you are given its size, shape, and material composition, at least if there are lots more moderator atoms than fuel atoms.
12 190 But what if you are asked to design a critical reactor out of a given material? That is, suppose you know that you want k=1 and you know the material properties, and your unknown is size and/or shape? Recall that the only number that matters regarding size and shape is So you should first treat B g 2 as your unknown and try to solve for it. But when you do so, you encounter a difficulty a Recall the expression we are using for k, and see what we need to solve for B g 2 if we want a critical reactor:. The presence of B g 2 in an exponent and in a denominator makes this problematic! So here is a trick that gets around the problem: exp{ B g 2 τ th } 1 B g 2 τ th. (29) This approximation is accurate when B g 2 τ th is small, which is the same limit in which our approximation for P FNL is accurate. If you plug this into your criticality expression, you will be able to solve algebraically for B g 2. Then you simply have to find a size and shape that produces this value of B g 2. Spectrum in Reactors Continuing the theme of putting pieces together, let s assemble our estimate of the neutron flux spectrum (i.e., the neutron distribution in energy) that we d expect to see in a large thermal reactor. We know that in the high-energy range (a few hundred kev to 10 MeV), the dominant phenomenon is that neutrons are born from fission and then scatter down to lower energies. The result is that in this energy range, the scalar-flux spectrum looks a lot like a fission spectrum. (In Chapter VIII, Eq. (20), the χ(e) term on the right-hand side dominates in this energy range.) In the slowing-down range (around an ev to a few hundred kev), the χ(e) term of Chapter VIII Eq. (20) is negligible, and the other term is very nearly proportional to 1/E, with sharp drops at resonances (where the Σ t term in the denominator has sharp increases). These drops are in such narrow energy ranges that they are basically invisible on a plot that covers a wide energy range.
13 191 In the thermal range (below approximately 1 ev), we learned in Chapter IX that the scalar flux is essentially Maxwellian, although at an effective neutron temperature that will usually be slightly higher than the temperature of the reactor material. We put this together in the figure below: f(e) 1E+14 1E+13 1E+12 1E+11 1E+10 1E+9 1E+8 1E+7 1E+6 1E+5 1E+4 1E+3 1E+2 1E+1 1E+0 1E-4 1E-3 1E-2 1E-1 1E+0 1E+1 1E+2 1E+3 1E+4 1E+5 1E+6 E (ev) Figure. Rough sketch of typical neutron flux spectrum in a large thermal reactor operating near room temperature.
VIII. Neutron Moderation and the Six Factors
Introduction VIII. Neutron Moderation and the Six Factors 130 We continue our quest to calculate the multiplication factor (keff) and the neutron distribution (in position and energy) in nuclear reactors.
More informationIII. Chain Reactions and Criticality
III. Chain Reactions and Criticality Introduction We know that neutron production and loss rates determine the behavior of a nuclear reactor. In this chapter we introduce some terms that help us describe
More informationLecture 20 Reactor Theory-V
Objectives In this lecture you will learn the following We will discuss the criticality condition and then introduce the concept of k eff.. We then will introduce the four factor formula and two group
More information17 Neutron Life Cycle
17 Neutron Life Cycle A typical neutron, from birth as a prompt fission neutron to absorption in the fuel, survives for about 0.001 s (the neutron lifetime) in a CANDU. During this short lifetime, it travels
More informationLectures on Applied Reactor Technology and Nuclear Power Safety. Lecture No 1. Title: Neutron Life Cycle
Lectures on Nuclear Power Safety Lecture No 1 Title: Neutron Life Cycle Department of Energy Technology KTH Spring 2005 Slide No 1 Outline of the Lecture Infinite Multiplication Factor, k Four Factor Formula
More informationNeutron reproduction. factor ε. k eff = Neutron Life Cycle. x η
Neutron reproduction factor k eff = 1.000 What is: Migration length? Critical size? How does the geometry affect the reproduction factor? x 0.9 Thermal utilization factor f x 0.9 Resonance escape probability
More informationNuclear Fission. 1/v Fast neutrons. U thermal cross sections σ fission 584 b. σ scattering 9 b. σ radiative capture 97 b.
Nuclear Fission 1/v Fast neutrons should be moderated. 235 U thermal cross sections σ fission 584 b. σ scattering 9 b. σ radiative capture 97 b. Fission Barriers 1 Nuclear Fission Q for 235 U + n 236 U
More informationLesson 8: Slowing Down Spectra, p, Fermi Age
Lesson 8: Slowing Down Spectra, p, Fermi Age Slowing Down Spectra in Infinite Homogeneous Media Resonance Escape Probability ( p ) Resonance Integral ( I, I eff ) p, for a Reactor Lattice Semi-empirical
More informationEnergy Dependence of Neutron Flux
Energy Dependence of Neutron Flux B. Rouben McMaster University Course EP 4D03/6D03 Nuclear Reactor Analysis (Reactor Physics) 2015 Sept.-Dec. 2015 September 1 Contents We start the discussion of the energy
More informationControl of the fission chain reaction
Control of the fission chain reaction Introduction to Nuclear Science Simon Fraser University Spring 2011 NUCS 342 April 8, 2011 NUCS 342 (Lecture 30) April 8, 2011 1 / 29 Outline 1 Fission chain reaction
More informationLesson 9: Multiplying Media (Reactors)
Lesson 9: Multiplying Media (Reactors) Laboratory for Reactor Physics and Systems Behaviour Multiplication Factors Reactor Equation for a Bare, Homogeneous Reactor Geometrical, Material Buckling Spherical,
More informationNUCLEAR SCIENCE ACAD BASIC CURRICULUM CHAPTER 5 NEUTRON LIFE CYCLE STUDENT TEXT REV 2. L th. L f U-235 FUEL MODERATOR START CYCLE HERE THERMAL NEUTRON
ACAD BASIC CURRICULUM NUCLEAR SCIENCE CHAPTER 5 NEUTRON LIFE CYCLE 346 RESONANCE LOSSES p 038 THERMAL NEUTRON 2 THERMAL NEUTRON LEAKAGE 52 THERMAL ABSORBED BY NON-FUEL ATOMS L th 07 THERMAL f 965 THERMAL
More informationNext we shall remove the only unphysical approximation we made in this CASE, which is that we ignored delayed neutrons.
71 Several observations are in order: 1. Because the terms in the [ ] are defined in terms of n, which depends on t, they will in general depend on t. (But not on position or energy, because position and
More informationNuclear Reactor Physics I Final Exam Solutions
.11 Nuclear Reactor Physics I Final Exam Solutions Author: Lulu Li Professor: Kord Smith May 5, 01 Prof. Smith wants to stress a couple of concepts that get people confused: Square cylinder means a cylinder
More informationFundamentals of Nuclear Reactor Physics
Fundamentals of Nuclear Reactor Physics E. E. Lewis Professor of Mechanical Engineering McCormick School of Engineering and Applied Science Northwestern University AMSTERDAM BOSTON HEIDELBERG LONDON NEW
More informationChain Reactions. Table of Contents. List of Figures
Chain Reactions 1 Chain Reactions prepared by Wm. J. Garland, Professor, Department of Engineering Physics, McMaster University, Hamilton, Ontario, Canada More about this document Summary: In the chapter
More informationNEUTRON MODERATION. LIST three desirable characteristics of a moderator.
Reactor Theory (eutron Characteristics) DOE-HDBK-1019/1-93 EUTRO MODERATIO EUTRO MODERATIO In thermal reactors, the neutrons that cause fission are at a much lower energy than the energy level at which
More informationVI. Chain Reaction. Two basic requirements must be filled in order to produce power in a reactor:
VI. Chain Reaction VI.1. Basic of Chain Reaction Two basic requirements must be filled in order to produce power in a reactor: The fission rate should be high. This rate must be continuously maintained.
More informationElastic scattering. Elastic scattering
Elastic scattering Now we have worked out how much energy is lost when a neutron is scattered through an angle, θ We would like to know how much energy, on average, is lost per collision In order to do
More informationChapter 1: Useful definitions
Chapter 1: Useful definitions 1.1. Cross-sections (review) The Nuclear and Radiochemistry class listed as a prerequisite is a good place to start. The understanding of a cross-section being fundamentai
More information2. The Steady State and the Diffusion Equation
2. The Steady State and the Diffusion Equation The Neutron Field Basic field quantity in reactor physics is the neutron angular flux density distribution: Φ( r r, E, r Ω,t) = v(e)n( r r, E, r Ω,t) -- distribution
More informationReactivity Coefficients
Reactivity Coefficients B. Rouben McMaster University Course EP 4D03/6D03 Nuclear Reactor Analysis (Reactor Physics) 2015 Sept.-Dec. 2015 September 1 Reactivity Changes In studying kinetics, we have seen
More informationThe trick is to multiply the numerator and denominator of the big fraction by the least common denominator of every little fraction.
Complex Fractions A complex fraction is an expression that features fractions within fractions. To simplify complex fractions, we only need to master one very simple method. Simplify 7 6 +3 8 4 3 4 The
More informationSolving the neutron slowing down equation
Solving the neutron slowing down equation Bertrand Mercier, Jinghan Peng To cite this version: Bertrand Mercier, Jinghan Peng. Solving the neutron slowing down equation. 2014. HAL Id: hal-01081772
More informationLecture 5 Nuclear Reactions
Objectives In this lecture you will learn the following We shall understand the concept of kinetic energy from the perspective of particle physics. We shall conclude that for all practical purposes, mass
More informationREACTOR PHYSICS ASPECTS OF PLUTONIUM RECYCLING IN PWRs
REACTOR PHYSICS ASPECTS OF PLUTONIUM RECYCLING IN s Present address: J.L. Kloosterman Interfaculty Reactor Institute Delft University of Technology Mekelweg 15, NL-2629 JB Delft, the Netherlands Fax: ++31
More informationNuclear Theory - Course 227 THERMAL REACTORS (BASIC DESIGN)
Nuclear Theory - Course 227 THERMAL REACTORS (BASC DESGN) When a U-235 nucleus fissions an average of 2.5 neutrons are released in addition to the energy. This suggests that these neutrons could be used
More informationThe moderator temperature coefficient MTC is defined as the change in reactivity per degree change in moderator temperature.
Moderator Temperature Coefficient MTC 1 Moderator Temperature Coefficient The moderator temperature coefficient MTC is defined as the change in reactivity per degree change in moderator temperature. α
More informationCross-Sections for Neutron Reactions
22.05 Reactor Physics Part Four Cross-Sections for Neutron Reactions 1. Interactions: Cross-sections deal with the measurement of interactions between moving particles and the material through which they
More information(Refer Slide Time: 01:17)
Heat and Mass Transfer Prof. S.P. Sukhatme Department of Mechanical Engineering Indian Institute of Technology, Bombay Lecture No. 7 Heat Conduction 4 Today we are going to look at some one dimensional
More information22.54 Neutron Interactions and Applications (Spring 2004) Chapter 7 (2/26/04) Neutron Elastic Scattering - Thermal Motion and Chemical Binding Effects
.54 Neutron Interactions and Applications (Spring 004) Chapter 7 (/6/04) Neutron Elastic Scattering - Thermal Motion and Chemical Binding Effects References -- J. R. Lamarsh, Introduction to Nuclear Reactor
More informationB. Rouben McMaster University Course EP 4D03/6D03 Nuclear Reactor Analysis (Reactor Physics) 2015 Sept.-Dec.
2: Fission and Other Neutron Reactions B. Rouben McMaster University Course EP 4D03/6D03 Nuclear Reactor Analysis (Reactor Physics) 2015 Sept.-Dec. 2015 September 1 Contents Concepts: Fission and other
More informationReactivity Balance & Reactor Control System
Reactivity Balance & Reactor Control System K.S. Rajan Professor, School of Chemical & Biotechnology SASTRA University Joint Initiative of IITs and IISc Funded by MHRD Page 1 of 6 Table of Contents 1 MULTIPLICATION
More informationChapter V: Interactions of neutrons with matter
Chapter V: Interactions of neutrons with matter 1 Content of the chapter Introduction Interaction processes Interaction cross sections Moderation and neutrons path For more details see «Physique des Réacteurs
More informationThe next three lectures will address interactions of charged particles with matter. In today s lecture, we will talk about energy transfer through
The next three lectures will address interactions of charged particles with matter. In today s lecture, we will talk about energy transfer through the property known as stopping power. In the second lecture,
More informationX. Neutron and Power Distribution
X. Neutron and Power Distribution X.1. Distribution of the Neutron Flux in the Reactor In order for the power generated by the fission reactions to be maintained at a constant level, the fission rate must
More informationNuclear Theory - Course 227. In the previous lesson the neutron multiplication factor (k) was defined as:.
Nuclear Theory - Course 227 NEU'l'RO~ MULTIPLICAT!ON:..FACTOR AND REACI'IVITY In the previous lesson the neutron multiplication factor (k) was defined as:. k = no. of neutrons in one generation no. of
More informationExcerpt from the Proceedings of the COMSOL Users Conference 2007 Grenoble
Excerpt from the Proceedings of the COSOL Users Conference 007 Grenoble Evaluation of the moderator temperature coefficient of reactivity in a PWR V. emoli *,, A. Cammi Politecnico di ilano, Department
More informationReactors and Fuels. Allen G. Croff Oak Ridge National Laboratory (ret.) NNSA/DOE Nevada Support Facility 232 Energy Way Las Vegas, NV
Reactors and Fuels Allen G. Croff Oak Ridge National Laboratory (ret.) NNSA/DOE Nevada Support Facility 232 Energy Way Las Vegas, NV July 19-21, 2011 This course is partially based on work supported by
More informationQuiz, Physics & Chemistry
Eight Sessions 1. Pressurized Water Reactor 2. Quiz, Thermodynamics & HTFF 3. Quiz, Physics & Chemistry 4. Exam #1, Electrical Concepts & Systems 5. Quiz, Materials Science 6. Quiz, Strength of Materials
More informationMCRT L8: Neutron Transport
MCRT L8: Neutron Transport Recap fission, absorption, scattering, cross sections Fission products and secondary neutrons Slow and fast neutrons Energy spectrum of fission neutrons Nuclear reactor safety
More informationSubcritical Multiplication and Reactor Startup
22.05 Reactor Physics - Part Twenty-Five Subcritical Multiplication and Reactor Startup 1. Reference Material See pp. 357-363 of the article, Light Water Reactor Control Systems, in Wiley Encyclopedia
More informationThe number of protons in the nucleus is known as the atomic number Z, and determines the chemical properties of the element.
I. NUCLEAR PHYSICS I.1 Atomic Nucleus Very briefly, an atom is formed by a nucleus made up of nucleons (neutrons and protons) and electrons in external orbits. The number of electrons and protons is equal
More informationToday, I will present the first of two lectures on neutron interactions.
Today, I will present the first of two lectures on neutron interactions. I first need to acknowledge that these two lectures were based on lectures presented previously in Med Phys I by Dr Howell. 1 Before
More informationEpisode 528: Controlling fission
Episode 528: Controlling fission In this episode, you can look at the different features of the core of a nuclear reactor, and explain its operation using your students knowledge of nuclear physics. Summary
More information3. State each of the four types of inelastic collisions, giving an example of each (zaa type example is acceptable)
Nuclear Theory - Course 227 OBJECTIVES to: At the conclusion of this course the trainee will be able 227.00-1 Nuclear Structure 1. Explain and use the ZXA notation. 2. Explain the concept of binding energy.
More informationMNFFY 221/SIF 4082 Energy and Environmental Physics. 2002
MNFFY 221/SIF 4082 Energy and Environmental Physics. 2002 Suggested solution to exam Problem 2 a) Show that the energy received from the sun earth is on average equal to the solar constant S given by 1
More informationLamarsh, "Introduction to Nuclear Reactor Theory", Addison Wesley (1972), Ch. 12 & 13
NEEP 428 REACTOR PULSING Page 1 April 2003 References: Lamarsh, "Introduction to Nuclear Reactor Theory", Addison Wesley (1972), Ch. 12 & 13 Notation: Lamarsh (2), "Introduction to Nuclear Engineering",(1975),
More informationLesson 6: Diffusion Theory (cf. Transport), Applications
Lesson 6: Diffusion Theory (cf. Transport), Applications Transport Equation Diffusion Theory as Special Case Multi-zone Problems (Passive Media) Self-shielding Effects Diffusion Kernels Typical Values
More informationLectures on Applied Reactor Technology and Nuclear Power Safety. Lecture No 5. Title: Reactor Kinetics and Reactor Operation
Lectures on Nuclear Power Safety Lecture No 5 Title: Reactor Kinetics and Reactor Operation Department of Energy Technology KTH Spring 2005 Slide No 1 Outline of the Lecture (1) Reactor Kinetics Reactor
More informationPart I Electrostatics. 1: Charge and Coulomb s Law July 6, 2008
Part I Electrostatics 1: Charge and Coulomb s Law July 6, 2008 1.1 What is Electric Charge? 1.1.1 History Before 1600CE, very little was known about electric properties of materials, or anything to do
More information1 v. L18.pdf Spring 2010, P627, YK February 22, 2012
L18.pdf Spring 2010, P627, YK February 22, 2012 18 T2 Nuclear Information Service at LANL: http://t2.lanl.gov/data/ ENDF/B VI Neutron Data : http://t2.lanl.gov/cgi bin/nuclides/endind Thermal neutron x
More informationNuclear Reactors. Richard W. Hillyer, Applied Physics, Christopher Newport University. Spring 2013
Nuclear Reactors A Discussion of Neutron Flux, Power Density, and Gamma Ray Buildup Flux Richard W. Hillyer, Applied Physics, Christopher Newport University Spring 2013 Advisors Dr. David Gore, Lecturer
More informationNeutron Diffusion Theory: One Velocity Model
22.05 Reactor Physics - Part Ten 1. Background: Neutron Diffusion Theory: One Velocity Model We now have sufficient tools to begin a study of the second method for the determination of neutron flux as
More informationIndian Institute of Technology Madras Present NPTEL NATIONAL PROGRAMME ON TECHNOLOGY ENHANCED LEARNING
Indian Institute of Technology Madras Present NPTEL NATIONAL PROGRAMME ON TECHNOLOGY ENHANCED LEARNING NUCLEAR REACTOR AND SAFETY AN INTRODUCTORY COURSE Module 02 Lecture 02 Basic Physics of Nuclear Fission
More informationNeutron Interactions Part I. Rebecca M. Howell, Ph.D. Radiation Physics Y2.5321
Neutron Interactions Part I Rebecca M. Howell, Ph.D. Radiation Physics rhowell@mdanderson.org Y2.5321 Why do we as Medical Physicists care about neutrons? Neutrons in Radiation Therapy Neutron Therapy
More informationMath101, Sections 2 and 3, Spring 2008 Review Sheet for Exam #2:
Math101, Sections 2 and 3, Spring 2008 Review Sheet for Exam #2: 03 17 08 3 All about lines 3.1 The Rectangular Coordinate System Know how to plot points in the rectangular coordinate system. Know the
More informationEigenvalues & Eigenvectors
Eigenvalues & Eigenvectors Page 1 Eigenvalues are a very important concept in linear algebra, and one that comes up in other mathematics courses as well. The word eigen is German for inherent or characteristic,
More informationUltraslow Wave Nuclear Burning of Uranium-Plutonium Fissile Medium on Epithermal Neutrons
Ultraslow Wave Nuclear Burning of Uranium-Plutonium Fissile Medium on Epithermal Neutrons V.D. Rusov 1, V.A. Tarasov 1, M.V. Eingorn 2, S.A. Chernezhenko 1, A.A. Kakaev 1, V.M. Vashchenko 3, M.E. Beglaryan
More informationCore Physics Second Part How We Calculate LWRs
Core Physics Second Part How We Calculate LWRs Dr. E. E. Pilat MIT NSED CANES Center for Advanced Nuclear Energy Systems Method of Attack Important nuclides Course of calc Point calc(pd + N) ϕ dn/dt N
More informationNuclear Theory - Course 127 NEUTRON BALANCE AND THE FOUR FACTOR FORMULA
' Nuclear Theory - Course 127 NEUTRON BALANCE AND THE FOUR FACTOR FORMULA When a reactor is operating at steady power, the chain reaction is just being maintained. One neutro~ only is available from each
More informationTransformed E&M I homework. Work and Energy (Griffiths Chapter 2)
Transformed E&M I homework Work and Energy (Griffiths Chapter 2) Work & Energy Question 1. Energy of point charge distribution Imagine a small square (side "a") with four point charges +q, one on each
More informationThe Physics of Nuclear Reactors. Heather King Physics 420
The Physics of Nuclear Reactors Heather King Physics 420 Nuclear Reactions A nuclear reaction is a reaction that involves atomic nuclei, or nuclear particles (protons, neutrons), producing products different
More informationNuclear Reactions. Fission Fusion
Nuclear Reactions Fission Fusion Nuclear Reactions and the Transmutation of Elements A nuclear reaction takes place when a nucleus is struck by another nucleus or particle. Compare with chemical reactions!
More informationNuclear Energy; Effects and Uses of Radiation
Nuclear Energy; Effects and Uses of Radiation Nuclear Reactions and the Transmutation of Elements A nuclear reaction takes place when a nucleus is struck by another nucleus or particle. Compare with chemical
More information2. The neutron may just bounce off (elastic scattering), and this can happen at all neutron energies.
Nuclear Theory - Course 227 NEUTRON CROSS SECTONS, NEUTRON DENSTY AND NEUTRON FLUX Neutron Cross Sections Let us have a look at the various reactions a neutron can undergo with a U-235 nucleus: As mentioned
More informationThe discovery of nuclear reactions need not bring about the destruction of mankind any more than the discovery of matches - Albert Einstein
The world has achieved brilliance without wisdom, power without conscience. Ours is a world of nuclear giants and ethical infants. - Omar Bradley (US general) The discovery of nuclear reactions need not
More informationStep 2: Calculate the total amount of U-238 present at time=0. Step 4: Calculate the rate constant for the decay process.
LP#9. A meteor contains 0.556 g of Pb-206 to every 1.00g U-238. Determine the age of the meteor. Step 1: Calculate the moles of each nuclide present. 0.566g Pb-206 x 1.00g U-238 x Step 2: Calculate the
More informationTheoretical Task 3 (T-3) : Solutions 1 of 9
Theoretical Task 3 (T-3) : Solutions of 9 The Design of a Nuclear Reactor Uranium occurs in nature as UO with only 0.70% of the uranium atoms being 35 U. Neutron induced fission occurs readily in 35 U
More informationMassachusetts Institute of Technology Physics Department
Massachusetts Institute of Technology Physics Department Physics 8.21 Fall 2011 Physics of Energy November 8, 2011 Quiz 2 Instructions Problem Points 1 50 2 25 3 25 (+ 20) Total 100 You must do problems
More informationChapter 10. Answers to examination-style questions. Answers Marks Examiner s tips. 1 (a) (i) 238. (ii) β particle(s) 1 Electron antineutrinos 1
(a) (i) 238 92 U + 0 n 239 92 U (ii) β particle(s) Electron antineutrinos (b) For: Natural uranium is 98% uranium-238 which would be otherwise unused. Plutonium-239 would not need to be stored long-term
More informationMeasuring the Properties of Stars (ch. 17) [Material in smaller font on this page will not be present on the exam]
Measuring the Properties of Stars (ch. 17) [Material in smaller font on this page will not be present on the exam] Although we can be certain that other stars are as complex as the Sun, we will try to
More informationSolving Quadratic & Higher Degree Equations
Chapter 9 Solving Quadratic & Higher Degree Equations Sec 1. Zero Product Property Back in the third grade students were taught when they multiplied a number by zero, the product would be zero. In algebra,
More informationQuadratic Equations Part I
Quadratic Equations Part I Before proceeding with this section we should note that the topic of solving quadratic equations will be covered in two sections. This is done for the benefit of those viewing
More informationCALCULATION OF TEMPERATURE REACTIVITY COEFFICIENTS IN KRITZ-2 CRITICAL EXPERIMENTS USING WIMS ABSTRACT
CALCULATION OF TEMPERATURE REACTIVITY COEFFICIENTS IN KRITZ-2 CRITICAL EXPERIMENTS USING WIMS D J Powney AEA Technology, Nuclear Science, Winfrith Technology Centre, Dorchester, Dorset DT2 8DH United Kingdom
More informationENEN/Reactor Theory/ Laboratory Session 1 DETERMINATION OF BASIC STATIC REACTOR PARAMETERS IN THE GRAPHITE PILE AT THE VENUS FACILITY
p1 Summary DETERMINATION OF BASIC STATIC REACTOR PARAMETERS IN THE GRAPHITE PILE AT THE VENUS FACILITY P. Baeten (pbaeten@sccen.be) The purpose of this laboratory session is the determination of the basic
More informationNeutronic analysis of SFR lattices: Serpent vs. HELIOS-2
Neutronic analysis of SFR lattices: Serpent vs. HELIOS-2 E. Fridman 1, R. Rachamin 1, C. Wemple 2 1 Helmholtz Zentrum Dresden Rossendorf 2 Studsvik Scandpower Inc. Text optional: Institutsname Prof. Dr.
More informationSlowing down the neutrons
Slowing down the neutrons Clearly, an obvious way to make a reactor work, and to make use of this characteristic of the 3 U(n,f) cross-section, is to slow down the fast, fission neutrons. This can be accomplished,
More informationLecture 14, 8/9/2017. Nuclear Reactions and the Transmutation of Elements Nuclear Fission; Nuclear Reactors Nuclear Fusion
Lecture 14, 8/9/2017 Nuclear Reactions and the Transmutation of Elements Nuclear Fission; Nuclear Reactors Nuclear Fusion Nuclear Reactions and the Transmutation of Elements A nuclear reaction takes place
More informationReactor Physics: Basic Definitions and Perspectives. Table of Contents
Reactor Physics - Basic Definitions and Perspectives Reactor Physics: Basic Definitions and Perspectives prepared by Wm. J. Garland, Professor, Department of Engineering Physics, McMaster University, Hamilton,
More informationThis is the third of three lectures on cavity theory.
This is the third of three lectures on cavity theory. 1 In this lecture, we are going to go over what is meant by charged particle equilibrium and look at the dose and kerma when you have charged particle
More informationChapter VIII: Nuclear fission
Chapter VIII: Nuclear fission 1 Summary 1. General remarks 2. Spontaneous and induced fissions 3. Nucleus deformation 4. Mass distribution of fragments 5. Number of emitted electrons 6. Radioactive decay
More informationSENSITIVITY ANALYSIS OF ALLEGRO MOX CORE. Bratislava, Iľkovičova 3, Bratislava, Slovakia
SENSITIVITY ANALYSIS OF ALLEGRO MOX CORE Jakub Lüley 1, Ján Haščík 1, Vladimír Slugeň 1, Vladimír Nečas 1 1 Institute of Nuclear and Physical Engineering, Slovak University of Technology in Bratislava,
More informationPHYS 352. Charged Particle Interactions with Matter. Intro: Cross Section. dn s. = F dω
PHYS 352 Charged Particle Interactions with Matter Intro: Cross Section cross section σ describes the probability for an interaction as an area flux F number of particles per unit area per unit time dσ
More informationClassroom notes for: Radiation and Life Thomas M. Regan Pinanski 207 ext 3283
Classroom notes for: Radiation and Life 98.101.201 Thomas M. Regan Pinanski 207 ext 3283 1 Thus, after the directly ionizing radiation has lost its energy, it is no longer radiation; it simply becomes
More informationFebruary 13, Option 9 Overview. Mind Map
Option 9 Overview Mind Map Return tests - will discuss Wed..1.1 J.1: #1def,2,3,6,7 (Sequences) 1. Develop and understand basic ideas about sequences. J.2: #1,3,4,6 (Monotonic convergence) A quick review:
More informationCarbon Dating. Principles of Radiometric Dating. 03 nuclear decay and the standard model June 05, 2013
Principles of Radiometric Dating http://facstaff.gpc.edu/~pgore/geology/geo102/radio.htm Naturally occurring radioactive materials break down into other materials at known rates. This is known as radioactive
More informationChapter 2 Nuclear Reactor Calculations
Chapter 2 Nuclear Reactor Calculations Keisuke Okumura, Yoshiaki Oka, and Yuki Ishiwatari Abstract The most fundamental evaluation quantity of the nuclear design calculation is the effective multiplication
More informationPhysicsAndMathsTutor.com 1
PhysicsAndMathsTutor.com 1 1. Describe briefly one scattering experiment to investigate the size of the nucleus of the atom. Include a description of the properties of the incident radiation which makes
More informationCRITICAL AND SUBCRITICAL EXPERIMENTS USING THE TRAINING NUCLEAR REACTOR OF THE BUDAPEST UNIVERSITY OF TECHNOLOGY AND ECONOMICS
CRITICAL AND SUBCRITICAL EXPERIMENTS USING THE TRAINING NUCLEAR REACTOR OF THE BUDAPEST UNIVERSITY OF TECHNOLOGY AND ECONOMICS É. M. Zsolnay Department of Nuclear Techniques, Budapest University of Technology
More information(1) The time t required for N generations to elapse is merely:
19 Changes In Reactor Power With Time The two preceding modules discussed how reactivity changes increase or decrease neutron flux and hence, change the thermal power output from the fuel. We saw how the
More informationLecture 27 Reactor Kinetics-III
Objectives In this lecture you will learn the following In this lecture we will understand some general concepts on control. We will learn about reactivity coefficients and their general nature. Finally,
More informationReactivity Effect of Fission and Absorption
Journal of NUCLEAR SCIENCE and TECHNOLOGY, 1, No. 7, p.246~254 (October, 1964). J. Nucl. Sci. Tech. Space Dependent Reactivity Effect of Fission and Absorption Tohru HAGA* and Iwao KOBAYASHI* Received
More informationElementary Non-Steady Phenomena
Elementary Non-Steady (Transient) Phenomena (T) Elementary Non-Steady Phenomena Because Transport deals with rates it is often the case that we must consider non-steady (or transient) operation (when the
More informationNuclear Physics Fundamental and Application Prof. H. C. Verma Department of Physics Indian Institute of Technology, Kanpur
Nuclear Physics Fundamental and Application Prof. H. C. Verma Department of Physics Indian Institute of Technology, Kanpur Lecture - 5 Semi empirical Mass Formula So, nuclear radius size we talked and
More informationFor the next several lectures, we will be looking at specific photon interactions with matter. In today s lecture, we begin with the photoelectric
For the next several lectures, we will be looking at specific photon interactions with matter. In today s lecture, we begin with the photoelectric effect. 1 The objectives of today s lecture are to identify
More informationSteady State Analysis of Small Molten Salt Reactor (Effect of Fuel Salt Flow on Reactor Characteristics)
610 Steady State Analysis of Small Molten Salt Reactor (Effect of Fuel Salt Flow on Reactor Characteristics) Takahisa YAMAMOTO,KoshiMITACHI and Takashi SUZUKI The Molten Salt Reactor (MSR) is a thermal
More information(a) (i) State the proton number and the nucleon number of X.
PhysicsAndMathsTutor.com 1 1. Nuclei of 218 84Po decay by the emission of an particle to form a stable isotope of an element X. You may assume that no emission accompanies the decay. (a) (i) State the
More informationChemical Reaction Engineering Prof. Jayant Modak Department of Chemical Engineering Indian Institute of Science, Bangalore
Chemical Reaction Engineering Prof. Jayant Modak Department of Chemical Engineering Indian Institute of Science, Bangalore Lecture No. # 26 Problem solving : Heterogeneous reactions Friends, in last few
More information22.54 Neutron Interactions and Applications (Spring 2004) Chapter 7 (2/26/04) Neutron Elastic Scattering - Thermal Motion and Chemical Binding Effects
.54 Neutron Interactions and Applications (Spring 004) Chapter 7 (/6/04) Neutron Elastic Scattering - Thermal Motion and Chemical Binding Effects References -- J. R. Lamarsh, Introduction to Nuclear Reactor
More information