Prediction of geometric dimensions for cold forgings using the finite element method

Size: px
Start display at page:

Download "Prediction of geometric dimensions for cold forgings using the finite element method"

Transcription

1 Journal of Materials Processing Technology 189 (2007) Prediction of geometric dimensions for cold forgings using the finite element method B.Y. Jun a, S.M. Kang b, M.C. Lee c, R.H. Park b, M.S. Joun b,d, a Technology Innovation Center of Gyeongsang National University, Gyeongsang National University, Jinju , Republic of Korea b School of Mechanical and Aerospace Engineering, Gyeongsang National University, Jinju , Republic of Korea c Department of Mechanical Engineering, Gyeongsang National University, Jinju , Republic of Korea d Research Center for Aircraft Parts Technology, Gyeongsang National University, Jinju , Republic of Korea Received 9 December 2005; received in revised form 21 December 2006; accepted 12 February 2007 Abstract In this paper, a practical approach for systematically estimating the geometric dimensions of cold forgings using the finite element method is presented. The forging process was simulated by a rigid-thermoplastic finite element method under the assumption that the dies and tools are rigid. Die structural and workpiece springback analyses were carried out using the information obtained from the forging simulation. The approach was applied to a test cold forging process. A comparison between predictions and measurements demonstrated that the proposed approach was acceptable for this application Elsevier B.V. All rights reserved. Keywords: Cold forgings; Finite element method; Die structural analysis; Springback analysis 1. Introduction The practice of forging has constantly advanced over the years, especially during the recent mass production of mechanical parts that combine a low price with good quality. Without forging technology, the mass production of cars, home appliances, etc., would be impossible. Most mechanical parts need machining after forging or casting. However, this machining leads to increased manufacturing costs since it requires considerable processing time, an investment in equipment, and an increase in labor. Usually, the minimization of a machining process directly reduces the workpiece, labor, and machining costs, which eventually impact on the price competitiveness of the product. Consequently, various attempts to reduce the machining cost have been made. Forging has been one of the best solutions, and precision forging can now be used to achieve a dimensional accuracy of less than 10 m in net-shape manufacturing. Much progress has Corresponding author at: School of Mechanical and Aerospace Engineering, Gyeongsang National University, Gazwa-dong 900, Jinju-City, GyeongNam , Republic of Korea. Tel.: ; fax: address: msjoun@gsnu.ac.kr (M.S. Joun). been made in the production of special forging technologies, including the enclosed-die forming method, divided-flow forming method, backpressure forming method, and combined new forging method. The dimensions of forgings are dependent mostly on the elastic deformation of the die and tool, springback of the workpiece, and thermal contraction of the workpiece. Heat treatment can also lead to dimensional changes in forgings. This means that producing accurate predictions of geometric forging dimensions is a difficult task. Research on the elastic deformation of dies and tools has been attempted by a few researchers [1 8], but their results have only been applied to solve very restricted problems. In spite of the importance of precision forging, there have been very few applicable and systematic tools introduced that can predict the dimensions of forgings. Therefore, most process design engineers depend on traditional experience-based rules and trial-and-error approaches to meet dimensional accuracy targets, leading to an increase in the cost and time of the process development. The ability to predict the final dimensions of forgings is of great importance to meet dimensional accuracy requirements in precision forging. In this paper, a useful finite element-based approach for predicting the geometric dimensions of cold forgings is presented with an application example from a cold forging company. The /$ see front matter 2007 Elsevier B.V. All rights reserved. doi: /j.jmatprotec

2 460 B.Y. Jun et al. / Journal of Materials Processing Technology 189 (2007) elastic deformation of the die, springback of the workpiece, and thermal contraction of the workpiece are considered in the proposed approach. 2. Methodology It is impossible to take into account all the factors and correlations when predicting the geometric dimensions of forgings. Consequently, some minor factors must be neglected in order to obtain engineering solutions. All parameters that affect the geometric dimensions of forgings may be more or less coupled, but most research studies neglect these correlations to obtain engineering solutions, as is the case in this study. A rigid-thermoplastic finite element method was employed. The dies and tools were assumed to be rigid in the forging simulation [9]. The simulation results, including force, temperature, and stress information, were employed to analyse the elastic deformation of the die and tool, and springback of the workpiece due to the release of mechanical and thermal loads. We assumed that the forming and thermal loads were removed instantly from the workpiece after forging and that the workpiece behaved elastically and isotropically. To predict the geometry of the workpiece, we added the elastic deformation of the die and tool to the springback of the workpiece, which were calculated independently. The concept explained above is shown in Fig. 1. Fig. 1(a) gives the geometry of the product, which was obtained from a forging simulation under the rigid-die assumption, where P is a point on the workpiece in the figure. Fig. 1(b) describes the die deformation, where d 1 in the figure is the displacement of the workpiece point P due to the die deformation. Fig. 1(c) shows the springback of the workpiece due to the removal of the forming and thermal loads, where d 2 in the figure is the displacement of workpiece point P due to the springback. In Fig. 1(d), the displacement d of point P is calculated by adding d 1 to d Theoretical background Fig. 2 shows a conceptual diagram of a contact problem between two objects. The objects have the same normal vector n i along the contacting interface. If the normal vector points outwards from the object, its corresponding boundary is denoted as Γ c + and the opposite boundary is denoted as Γc. Here, Γ c indicates both Γ c + and Γc. Under the assumption that the interface obeys the law of Coulomb friction, the geometrical and mechanical boundary conditions on Γ c are formulated as follows. In the normal direction: u +c n = u c n if σ n +c = σn c < 0 (1) σ n +c = 0 if u +c n u c n < 0 (2) In the tangential direction: σ t +c = σ t +c = μ σ +c (u c t u +c t ) n u c t u +c t if u c t u +c t (3) Fig. 1. Basic approach used to estimate the geometric dimensions of cold forgings: (a) results of the forging simulation, (b) elastic deformation of the die, (c) springback of the workpiece, and (d) final geometry of the product.

3 B.Y. Jun et al. / Journal of Materials Processing Technology 189 (2007) β t (u +c t Γ ct u c t )(δu +c t δu c t )dγ σ t +c δu +c t dγ = 0 (7) Γ cs where Γ cn ( Γ c ) is the mechanically contacting boundary on which σ n +c < 0, Γ cs and Γ ct (Γ cn = Γ ct Γ cs ) are the boundaries governed by Eqs. (3) and (4), respectively, and β n and β t are large positive constants whose physical meanings can be expressed as: σ n +c = β n (u +c n u c n ) (8) σ t +c = β t (u +c t u c t ) (9) The die is assumed to be linear-elastic and isotropic. In this case, the stress strain relationship can be expressed as: σ ij = E 1 + ν ε νe ij + (1 + ν)(1 2ν) ε kkδ ij αe 1 2ν Tδ ij (10) where E, ν, and α are Young s modulus, Poisson s ratio, and the coefficient of thermal expansion, respectively, T the temperature difference, and δ ij is the Kronecker delta. Here, α may differ from direction to direction as well as from position to position [8]. Detailed solution schemes have been presented and proven in Ref. [8]. Fig. 2. Conceptual diagram of a contact problem: (a) problem description and (b) contact surface. u c t = u +c t if σ +c t <μ σ +c n (4) where μ is the coefficient of Coulomb friction and the subscripts n and t denote the n-component and t-component, respectively, in the local coordinate system shown in Fig. 2. Superscripts +c and c in the stress and velocity components specify their related values at Γ c + and Γc, respectively. For example: u +c n = u i n i, σ n +c = σ ij n i n j on Γ c + (5) u c n = u i n i, σn c = σ ij n i n j on Γc (6) where u i is the displacement vector and σ ij is the stress tensor. Note that n i on Γ c + points outwards from the object while n i on Γc points inwards from the other object. Eqs. (3) and (4) imply that the tangential stress is governed by the law of Coulomb friction if sliding takes place along the interface. The contacting interface is considered to be a no-slip region if the tangential stress is less than μ σ n. Using a penalty method, one can imbed Eqs. (1) and (4) into the virtual work principle as follows: σ ij δε ij dω f i δu i dω t i δu i dγ Γ ti Ω + β n (u +c n Γ cn Ω u c n )(δu+c n δu c n )dγ 4. Application example 4.1. Test cold forging process Fig. 3 describes the cold forging process sequence that was selected as a test for the proposed geometrical estimation approach. This process is quite simple, as shown in the Fig. 3. Forging sequence of the selected test example: (a) first stage and (b) second stage.

4 462 B.Y. Jun et al. / Journal of Materials Processing Technology 189 (2007) Fig. 5. Predicted metal flow lines. Fig. 4. Design of the die set. figure, and thus appropriate for such a test. The process is composed of two cold forging stages. The workpiece was SCM420H, which was annealed before each forging stage. The detailed design of the die and tool geometry employed in the second stage is shown in Fig. 4. The die insert was shrink fitted by a 400 C temperature difference and all the die parts were made of SKD11. Before forging, the die geometry was measured with a precision coordinate measuring machine. This measured geometry was used in the simulation to determine the basic information required to predict the geometric dimensions of the forging. Two cases with t = 5.0 and 4.6 mm, defined in Fig. 3, were considered. The process conditions and material properties used in the simulation are given in Table 1. The thermal properties of the workpiece and die/tool, and the thermal process conditions used in the simulation can be found in Ref. [10]. Since the simulation results of the two cases were nearly the same, only the results of the t = 4.6 mm case are given in Figs Fig. 5 shows the metal flow lines and Fig. 6 shows the traction vectors for which the maximum normal component was 2330 MPa. Fig. 7 shows the temperature distributions, just after forming in Fig. 7(a) and 10 s later in Fig. 7(b). These reveal that the workpiece temperature had risen by an average of 58 C. The traction vectors were used for the deformation analysis of the die as well as the springback analysis of the workpiece, while the temperature distribution was used for the thermal contraction analysis of the workpiece. In this study, the effect of the temperature rise of the die on the material was neglected Die deformation analysis The die structure is shown in Fig. 4. The material properties of the die parts are given in Table 2. Fig. 8 shows the finite element model with boundary conditions that was used for the die structural analysis. The deformation-enlarged configuration of the die structure is given in Fig. 9 with the nodal displacements multiplied by 10. The effective stress distributions are shown in Fig. 10. Table 1 Material properties and process conditions for the cold forging process simulation Flow stress, σ (MPa) ε 0.2 Coefficient of Coulomb friction, μ 0.1 Coefficient of thermal expansion, α (/ C) Initial temperature of material ( C) 20 Initial temperature of die ( C) 20 Fig. 6. Stress vectors (MPa).

5 B.Y. Jun et al. / Journal of Materials Processing Technology 189 (2007) Fig. 9. Deformation of the die set due to the forming load and shrink fit (Nodal displacements are enlarged 10 times.) Springback of the workpiece Fig. 7. Temperature distribution ( C) (a) at the end of the stroke and (b) 10 s after forming. Information used for the analysis of the springback due to the release of mechanical and thermal loads is given in Table 3. The analysis results are given in Fig. 11 with the nodal displacements multiplied by Comparison of analysis results with measurements Radial displacements at points P, Q, and R on the workpiece and points P, Q, and R on the die, shown in Fig. 12, were used to compare the analysis results with measurements. The distances measured from the central line to the points P, Q, and R before forming were , , and mm, respectively. The analyzed and measured results are summarized in Table 4 for t = 4.6 mm and in Table 5 for t = 5.0 mm. When t = 4.6 mm, the predicted radial displacement of point Q due to the springback and thermal contraction of the workpiece was mm Table 2 Material properties and process conditions for the die parts Modulus of elasticity, E (GPa) 220 Poisson s ratio, ν 0.3 Coefficient of Coulomb friction, μ 0.1 Coefficient of thermal expansion, α (/ C) Table 3 Material properties and process conditions for the springback of the workpiece Fig. 8. Finite element model for the die structural analysis. Modulus of elasticity, E (GPa) 210 Poisson s ratio, ν 0.3 Coefficient of thermal expansion, α (/ C)

6 464 B.Y. Jun et al. / Journal of Materials Processing Technology 189 (2007) Fig. 10. Effective stress distributions (MPa). Fig. 12. Test points selected for comparison in the radial direction: (a) workpiece and (b) die. Fig. 11. Springback of the workpiece due to mechanical and thermal loads (Nodal displacements are enlarged 10 times.). and the predicted radial displacement of the point due to the die deformation was mm. Thus, the related point of the workpiece moved outwards by mm so that the predicted dimension of the forging was mm greater than that of the die. The difference between the radius of the die and workpiece in the measurements taken at point Q was mm, yielding a prediction error of approximately 30%. The errors at points P and R, calculated in the same manner, were 38% and 8%, respectively. As shown in Table 5, the results of the t = 5.0 mm case were nearly the same. The same procedures were applied to investigate the accuracy of the proposed geometric estimation approach in the axial direction. The difference y between the two points A and B shown in Fig. 13 was obtained for both the predictions and measurements. The prediction considered the springback, thermal contraction of the workpiece, and deformation of the die (see Fig. 14). The results are summarized and compared in Table 6. Table 4 Comparison of the predicted radial displacements against measured values for t = 4.6 mm P Q R Deformation of die, d 1 (mm) Springback of material, d 2 (mm) Prediction, d = d 1 + d 2 (mm) Measurement, a (mm) d/a (%) Table 5 Comparison of the predicted radial displacements against measured values for t = 5.0 mm P Q R Deformation of die, d 1 (mm) Springback of material, d 2 (mm) Prediction, d = d 1 + d 2 (mm) Measurement, a (mm) d/a (%)

7 B.Y. Jun et al. / Journal of Materials Processing Technology 189 (2007) The differences between the predictions and measurements were less than 9%. 5. Conclusions Fig. 13. Definition of y. In this paper, a systematic approach for predicting the geometric dimensions of cold forgings was proposed. The approach employed a rigid-thermoplastic finite element method to simulate the forging and an elastic finite element method to model both the elastic deformation of the die and provide a springback analysis of the workpiece. Both the mechanical and thermal loads were considered in the springback analysis. The mechanical load was applied due to the elastic unloading of the forming load while the thermal load was applied due to the cooling of the increased forging temperature to room temperature. All of the results were superposed to yield the final dimensions of the cold forged product. The predictions were compared with measurements and results were qualitatively very close. With the support of experience, the proposed approach can be a useful tool for process design in precision cold forging. Acknowledgement This work was supported by the K-MEM R&D Cluster Project of Kyongnam Province in Korea. References Fig. 14. Test points for comparison in the axial direction: (a) workpiece and (b) die. Table 6 Comparison of predicted vs. measured axial displacements t = 4.6 mm t = 5.0 mm Deformation of die, y S (mm) Springback of material, y D (mm) Prediction, A = y S + y D (mm) Measurement, B (mm) (B/A) 100 (%) [1] U. Engel, M. Hansel, FEM-simulation of fatigue crack growth in cold forging dies, in: Advanced Technology of Plasticity 1990: Proceedings of the 3rd International Conference on Technology of Plasticity, vol. 1, Kyoto, Japan, 1990, pp [2] Z. Xing-hua, Finite element analysis of container and accuracy control of extrusion products, in: Advanced Technology of Plasticity 1990: Proceedings of the 3rd International Conference on Technology of Plasticity, vol. 1, Kyoto, Japan, 1990, pp [3] K. Lange, A. Hettig, M. Knoerr, Increasing tool life in cold forging through advanced design and tool manufacturing techniques, J. Mater. Process. Technol. 35 (1992) [4] K.F. Hoffmann, K. Lange, Computation of the elastic expansion and stresses in cold extrusion dies with non-axisymmetric inner shape, Trans. NAMRI/SME 17 (1989) [5] S. Takahashi, C.A. Brebbia, Forging die stress analysis using boundary element method, in: Advanced Technology of Plasticity 1990: Proceedings of the 3rd International Conference on Technology of Plasticity, vol. 1, Kyoto, Japan, 1990, pp [6] Y. Ochial, R. Wadabayashi, Application of boundary element method to cold forging die design, in: Advanced Technology of Plasticity 1987: Proceedings of the 2nd International Conference on Technology of Plasticity, vol. 1, Stuttgart, Germany, 1987, pp [7] M. Fu, B. Shang, Stress analysis of the precision forging die for a bevel gear and its optimal design using the boundary-element method, J. Mater. Process. Technol. 53 (1995) [8] M.S. Joun, M.C. Lee, J.M. Park, Finite element analysis of prestressed die set in cold forging, Int. J. Mach. Tools Manuf. 42 (2002) [9] M.S. Joun, M.C. Lee, Quadrilateral finite-element generation and mesh quality control for metal forming simulation, Int. J. Numer. Methods Eng. 40 (1997) [10] M.S. Joun, H.K. Moon, R. Shivpuri, Automatic simulation of a sequence of hot-former forging processes by a rigid-thermoviscoplastic finite element method, J. Eng. Mater. Technol. Trans. ASME 120 (1998)

Optimization of blank dimensions to reduce springback in the flexforming process

Optimization of blank dimensions to reduce springback in the flexforming process Journal of Materials Processing Technology 146 (2004) 28 34 Optimization of blank dimensions to reduce springback in the flexforming process Hariharasudhan Palaniswamy, Gracious Ngaile, Taylan Altan ERC

More information

A novel technique of friction and material property measurement by tip test in cold forging

A novel technique of friction and material property measurement by tip test in cold forging A novel technique of friction and material property measurement by tip test in cold forging Y T Im*, S H Kang, and J S Cheon Department of Mechanical Engineering, Korea Advanced Institute of Science and

More information

End forming of thin-walled tubes

End forming of thin-walled tubes Journal of Materials Processing Technology 177 (2006) 183 187 End forming of thin-walled tubes M.L. Alves a, B.P.P. Almeida b, P.A.R. Rosa b, P.A.F. Martins b, a Escola Superior de Tecnologia e Gestão

More information

A study of forming pressure in the tube-hydroforming process

A study of forming pressure in the tube-hydroforming process Journal of Materials Processing Technology 192 19 (2007) 404 409 A study of forming pressure in the tube-hydroforming process Fuh-Kuo Chen, Shao-Jun Wang, Ray-Hau Lin Department of Mechanical Engineering,

More information

An alternative design method for the double-layer combined die using autofrettage theory

An alternative design method for the double-layer combined die using autofrettage theory https://doi.org/10.5194/ms-8-267-2017 Author(s) 2017. This work is distributed under the Creative Commons Attribution.0 License. An alternative design method for the double-layer combined die using autofrettage

More information

A FINITE ELEMENT STUDY OF ELASTIC-PLASTIC HEMISPHERICAL CONTACT BEHAVIOR AGAINST A RIGID FLAT UNDER VARYING MODULUS OF ELASTICITY AND SPHERE RADIUS

A FINITE ELEMENT STUDY OF ELASTIC-PLASTIC HEMISPHERICAL CONTACT BEHAVIOR AGAINST A RIGID FLAT UNDER VARYING MODULUS OF ELASTICITY AND SPHERE RADIUS Proceedings of the International Conference on Mechanical Engineering 2009 (ICME2009) 26-28 December 2009, Dhaka, Bangladesh ICME09- A FINITE ELEMENT STUDY OF ELASTIC-PLASTIC HEMISPHERICAL CONTACT BEHAVIOR

More information

Effect of various stress ratio parameters on cold upset forging of irregular shaped billets using white grease as lubricant

Effect of various stress ratio parameters on cold upset forging of irregular shaped billets using white grease as lubricant Indian Journal of Engineering & Materials Sciences Vol. 13, August 2006, pp. 281-292 Effect of various stress ratio parameters on cold upset forging of irregular shaped billets using white grease as lubricant

More information

Fig. 1. Circular fiber and interphase between the fiber and the matrix.

Fig. 1. Circular fiber and interphase between the fiber and the matrix. Finite element unit cell model based on ABAQUS for fiber reinforced composites Tian Tang Composites Manufacturing & Simulation Center, Purdue University West Lafayette, IN 47906 1. Problem Statement In

More information

Fundamentals of Linear Elasticity

Fundamentals of Linear Elasticity Fundamentals of Linear Elasticity Introductory Course on Multiphysics Modelling TOMASZ G. ZIELIŃSKI bluebox.ippt.pan.pl/ tzielins/ Institute of Fundamental Technological Research of the Polish Academy

More information

The Nonlinear Dynamic Behavior Analysis and Research for Sheet Steel Stamping Forming Problems Based on Finite Element Method

The Nonlinear Dynamic Behavior Analysis and Research for Sheet Steel Stamping Forming Problems Based on Finite Element Method Send Orders for Reprints to reprints@benthamscience.ae 198 The Open Materials Science Journal, 2015, 9, 198-202 Open Access The Nonlinear Dynamic Behavior Analysis and Research for Sheet Steel Stamping

More information

RESEARCH AND MEASUREMENTS OF VELOCITY FIELD DURING EXTRUSION PROCESS

RESEARCH AND MEASUREMENTS OF VELOCITY FIELD DURING EXTRUSION PROCESS XIX IMEKO World Congress Fundamental and Applied Metrology September 6-11, 29, Lisbon, Portugal RESEARCH AND MEASUREMENTS OF VELOCITY FIELD DURING EXTRUSION PROCESS Leo Gusel 1, Rebeka Rudolf 1 1 Faculty

More information

INVERSE METHOD FOR FLOW STRESS PARAMETERS IDENTIFICATION OF TUBE BULGE HYDROFORMING CONSIDERING ANISOTROPY

INVERSE METHOD FOR FLOW STRESS PARAMETERS IDENTIFICATION OF TUBE BULGE HYDROFORMING CONSIDERING ANISOTROPY 7 th EUROMECH Solid Mechanics Conference J. Ambrósio et.al. (eds.) Lisbon, Portugal, September 7-11, 2009 INVERSE METHOD FOR FLOW STRESS PARAMETERS IDENTIFICATION OF TUBE BULGE HYDROFORMING CONSIDERING

More information

Finite Element Method in Geotechnical Engineering

Finite Element Method in Geotechnical Engineering Finite Element Method in Geotechnical Engineering Short Course on + Dynamics Boulder, Colorado January 5-8, 2004 Stein Sture Professor of Civil Engineering University of Colorado at Boulder Contents Steps

More information

Prediction of Elastic Constants on 3D Four-directional Braided

Prediction of Elastic Constants on 3D Four-directional Braided Prediction of Elastic Constants on 3D Four-directional Braided Composites Prediction of Elastic Constants on 3D Four-directional Braided Composites Liang Dao Zhou 1,2,* and Zhuo Zhuang 1 1 School of Aerospace,

More information

Elements of Continuum Elasticity. David M. Parks Mechanics and Materials II February 25, 2004

Elements of Continuum Elasticity. David M. Parks Mechanics and Materials II February 25, 2004 Elements of Continuum Elasticity David M. Parks Mechanics and Materials II 2.002 February 25, 2004 Solid Mechanics in 3 Dimensions: stress/equilibrium, strain/displacement, and intro to linear elastic

More information

A Finite Element Study of Elastic-Plastic Hemispherical Contact Behavior against a Rigid Flat under Varying Modulus of Elasticity and Sphere Radius

A Finite Element Study of Elastic-Plastic Hemispherical Contact Behavior against a Rigid Flat under Varying Modulus of Elasticity and Sphere Radius Engineering, 2010, 2, 205-211 doi:10.4236/eng.2010.24030 Published Online April 2010 (http://www. SciRP.org/journal/eng) 205 A Finite Element Study of Elastic-Plastic Hemispherical Contact Behavior against

More information

PREDICTION OF FATIGUE LIFE OF COLD FORGING TOOLS BY FE SIMULATION AND COMPARISON OF APPLICABILITY OF DIFFERENT DAMAGE MODELS

PREDICTION OF FATIGUE LIFE OF COLD FORGING TOOLS BY FE SIMULATION AND COMPARISON OF APPLICABILITY OF DIFFERENT DAMAGE MODELS PREDICTION OF FATIGUE LIFE OF COLD FORGING TOOLS BY FE SIMULATION AND COMPARISON OF APPLICABILITY OF DIFFERENT DAMAGE MODELS M. Meidert and C. Walter Thyssen/Krupp Presta AG Liechtenstein FL-9492 Eschen

More information

PSEUDO ELASTIC ANALYSIS OF MATERIAL NON-LINEAR PROBLEMS USING ELEMENT FREE GALERKIN METHOD

PSEUDO ELASTIC ANALYSIS OF MATERIAL NON-LINEAR PROBLEMS USING ELEMENT FREE GALERKIN METHOD Journal of the Chinese Institute of Engineers, Vol. 27, No. 4, pp. 505-516 (2004) 505 PSEUDO ELASTIC ANALYSIS OF MATERIAL NON-LINEAR PROBLEMS USING ELEMENT FREE GALERKIN METHOD Raju Sethuraman* and Cherku

More information

Debonding process in composites using BEM

Debonding process in composites using BEM Boundary Elements XXVII 331 Debonding process in composites using BEM P. Prochazka & M. Valek Czech Technical University, Prague, Czech Republic Abstract The paper deals with the debonding fiber-matrix

More information

Arch. Metall. Mater. 62 (2017), 1, 85-90

Arch. Metall. Mater. 62 (2017), 1, 85-90 Arch. Metall. Mater. 62 (2017), 1, 85-90 DOI: 10.1515/amm-2017-0011 Z. PATER* # FEM ANALYSIS OF LOADS AND TORQUE IN A SKEW ROLLING PROCESS FOR PRODUCING AXISYMMETRIC PARTS Skew rolling is a metal forming

More information

A parametric study on the elastic-plastic deformation of a centrally heated two-layered composite cylinder with free ends

A parametric study on the elastic-plastic deformation of a centrally heated two-layered composite cylinder with free ends Arch. Mech., 68, 3, pp. 03 8, Warszawa 06 A parametric study on the elastic-plastic deformation of a centrally heated two-layered composite cylinder with free ends F. YALCIN ), A. OZTURK ), M. GULGEC 3)

More information

Methodology for the evaluation of yield strength and hardening behavior of metallic materials by indentation with spherical tip

Methodology for the evaluation of yield strength and hardening behavior of metallic materials by indentation with spherical tip JOURNAL OF APPLIED PHYSICS VOLUME 94, NUMBER 1 1 JULY 2003 Methodology for the evaluation of yield strength and hardening behavior of metallic materials by indentation with spherical tip Dejun Ma Department

More information

An investigation of involute and lead deflection in hot precision forging of gears

An investigation of involute and lead deflection in hot precision forging of gears DOI 10.1007/s00170-016-9003-8 ORIGINAL ARTICLE An investigation of involute and lead deflection in hot precision forging of gears Bin Zuo 1 & Baoyu Wang 1 & Zhi Li 1 & Nan Li & Jianguo Lin 1, Received:

More information

Stresses Analysis of Petroleum Pipe Finite Element under Internal Pressure

Stresses Analysis of Petroleum Pipe Finite Element under Internal Pressure ISSN : 48-96, Vol. 6, Issue 8, ( Part -4 August 06, pp.3-38 RESEARCH ARTICLE Stresses Analysis of Petroleum Pipe Finite Element under Internal Pressure Dr.Ragbe.M.Abdusslam Eng. Khaled.S.Bagar ABSTRACT

More information

Arbitrary Normal and Tangential Loading Sequences for Circular Hertzian Contact

Arbitrary Normal and Tangential Loading Sequences for Circular Hertzian Contact Arbitrary Normal and Tangential Loading Sequences for Circular Hertzian Contact Philip P. Garland 1 and Robert J. Rogers 2 1 School of Biomedical Engineering, Dalhousie University, Canada 2 Department

More information

Influence of friction in material characterization in microindentation measurement

Influence of friction in material characterization in microindentation measurement Influence of friction in material characterization in microindentation measurement W.C. Guo a,b,, G. Rauchs c, W.H. Zhang b, J.P. Ponthot a a LTAS. Department of Aerospace & Mechanical Engineering, University

More information

Back Calculation of Rock Mass Modulus using Finite Element Code (COMSOL)

Back Calculation of Rock Mass Modulus using Finite Element Code (COMSOL) Back Calculation of Rock Mass Modulus using Finite Element Code (COMSOL) Amirreza Ghasemi 1. Introduction Deformability is recognized as one of the most important parameters governing the behavior of rock

More information

Partitioned Formulation for Solving 3D Frictional Contact Problems with BEM using Localized Lagrange Multipliers

Partitioned Formulation for Solving 3D Frictional Contact Problems with BEM using Localized Lagrange Multipliers Copyright c 2007 ICCES ICCES, vol.2, no.1, pp.21-27, 2007 Partitioned Formulation for Solving 3D Frictional Contact Problems with BEM using Localized Lagrange Multipliers L. Rodríguez-Tembleque 1, J.A.

More information

Thermal load-induced notch stress intensity factors derived from averaged strain energy density

Thermal load-induced notch stress intensity factors derived from averaged strain energy density Available online at www.sciencedirect.com Draft ScienceDirect Draft Draft Structural Integrity Procedia 00 (2016) 000 000 www.elsevier.com/locate/procedia 21st European Conference on Fracture, ECF21, 20-24

More information

A STUDY ON THE FRACTURE A SIROCCO FAN IMPELLER

A STUDY ON THE FRACTURE A SIROCCO FAN IMPELLER FIFTH INTERNATIONAL CONGRESS ON SOUND AND VIBRATION DECEMBER 15-18, 1997 ADELAIDE, SOUTH AUSTRALIA A STUDY ON THE FRACTURE A SIROCCO FAN IMPELLER OF S.P. Lee, C.O. Ahn, H.S. Rew, S.C. Park, Y.M. Park and

More information

Example-3. Title. Description. Cylindrical Hole in an Infinite Mohr-Coulomb Medium

Example-3. Title. Description. Cylindrical Hole in an Infinite Mohr-Coulomb Medium Example-3 Title Cylindrical Hole in an Infinite Mohr-Coulomb Medium Description The problem concerns the determination of stresses and displacements for the case of a cylindrical hole in an infinite elasto-plastic

More information

Mechanical Properties of Materials

Mechanical Properties of Materials Mechanical Properties of Materials Strains Material Model Stresses Learning objectives Understand the qualitative and quantitative description of mechanical properties of materials. Learn the logic of

More information

Prediction of the bilinear stress-strain curve of engineering material by nanoindentation test

Prediction of the bilinear stress-strain curve of engineering material by nanoindentation test Prediction of the bilinear stress-strain curve of engineering material by nanoindentation test T.S. Yang, T.H. Fang, C.T. Kawn, G.L. Ke, S.Y. Chang Institute of Mechanical & Electro-Mechanical Engineering,

More information

Prediction of dynamic behavior of workpieces in ultrasonic plastic welding

Prediction of dynamic behavior of workpieces in ultrasonic plastic welding Prediction of dynamic behavior of workpieces in ultrasonic plastic welding Takao HIRAI** Fumiyasu KURATANI** Tatsuya YOSHIDA** and Saiji WASHIO*** **Department of Mechanical Engineering, Graduate School

More information

EFFECT OF STRAIN HARDENING ON ELASTIC-PLASTIC CONTACT BEHAVIOUR OF A SPHERE AGAINST A RIGID FLAT A FINITE ELEMENT STUDY

EFFECT OF STRAIN HARDENING ON ELASTIC-PLASTIC CONTACT BEHAVIOUR OF A SPHERE AGAINST A RIGID FLAT A FINITE ELEMENT STUDY Proceedings of the International Conference on Mechanical Engineering 2009 (ICME2009) 26-28 December 2009, Dhaka, Bangladesh ICME09- EFFECT OF STRAIN HARDENING ON ELASTIC-PLASTIC CONTACT BEHAVIOUR OF A

More information

Estimate of consumed energy at backward extrusion process by means of modelling approach

Estimate of consumed energy at backward extrusion process by means of modelling approach Journal of Materials Processing Technology 53 54 (2004) 907 92 Estimate of consumed energy at backward extrusion process by means of ling approach B. Barisic a,, G. Cukor a, M. Math b a Faculty of Engineering,

More information

New Representation of Bearings in LS-DYNA

New Representation of Bearings in LS-DYNA 13 th International LS-DYNA Users Conference Session: Aerospace New Representation of Bearings in LS-DYNA Kelly S. Carney Samuel A. Howard NASA Glenn Research Center, Cleveland, OH 44135 Brad A. Miller

More information

The effect of restraints type on the generated stresses in gantry crane beam

The effect of restraints type on the generated stresses in gantry crane beam The effect of restraints type on the generated stresses in gantry crane beam Leszek Sowa 1,*, Wiesława Piekarska 1, Tomasz Skrzypczak 1, Paweł Kwiatoń 1 1 Czestochowa University of Technology, Institute

More information

Design of a fastener based on negative Poisson's ratio foam adapted from

Design of a fastener based on negative Poisson's ratio foam adapted from 1 Design of a fastener based on negative Poisson's ratio foam adapted from Choi, J. B. and Lakes, R. S., "Design of a fastener based on negative Poisson's ratio foam", Cellular Polymers, 10, 205-212 (1991).

More information

UNLOADING OF AN ELASTIC-PLASTIC LOADED SPHERICAL CONTACT

UNLOADING OF AN ELASTIC-PLASTIC LOADED SPHERICAL CONTACT 2004 AIMETA International Tribology Conference, September 14-17, 2004, Rome, Italy UNLOADING OF AN ELASTIC-PLASTIC LOADED SPHERICAL CONTACT Yuri KLIGERMAN( ), Yuri Kadin( ), Izhak ETSION( ) Faculty of

More information

Crack Tip Plastic Zone under Mode I Loading and the Non-singular T zz -stress

Crack Tip Plastic Zone under Mode I Loading and the Non-singular T zz -stress Crack Tip Plastic Zone under Mode Loading and the Non-singular T -stress Yu.G. Matvienko Mechanical Engineering Research nstitute of the Russian Academy of Sciences Email: ygmatvienko@gmail.com Abstract:

More information

THE EFFECT OF GEOMETRY ON FATIGUE LIFE FOR BELLOWS

THE EFFECT OF GEOMETRY ON FATIGUE LIFE FOR BELLOWS Advanced Materials Development and Performance (AMDP2011) International Journal of Modern Physics: Conference Series Vol. 6 (2012) 343-348 World Scientific Publishing Company DOI: 10.1142/S2010194512003418

More information

TIME-DEPENDENT BEHAVIOR OF PILE UNDER LATERAL LOAD USING THE BOUNDING SURFACE MODEL

TIME-DEPENDENT BEHAVIOR OF PILE UNDER LATERAL LOAD USING THE BOUNDING SURFACE MODEL TIME-DEPENDENT BEHAVIOR OF PILE UNDER LATERAL LOAD USING THE BOUNDING SURFACE MODEL Qassun S. Mohammed Shafiqu and Maarib M. Ahmed Al-Sammaraey Department of Civil Engineering, Nahrain University, Iraq

More information

The Rotating Inhomogeneous Elastic Cylinders of. Variable-Thickness and Density

The Rotating Inhomogeneous Elastic Cylinders of. Variable-Thickness and Density Applied Mathematics & Information Sciences 23 2008, 237 257 An International Journal c 2008 Dixie W Publishing Corporation, U. S. A. The Rotating Inhomogeneous Elastic Cylinders of Variable-Thickness and

More information

Stress analysis of functionally graded discs under mechanical and thermal loads

Stress analysis of functionally graded discs under mechanical and thermal loads Indian Journal of Engineering & Materials Sciences Vol. 8, April 0, pp. -8 Stress analysis of functionally graded discs under mechanical and thermal loads Hasan Çallioğlu, Metin Sayer* & Ersin Demir Department

More information

Elastic-plastic deformation near the contact surface of the circular disk under high loading

Elastic-plastic deformation near the contact surface of the circular disk under high loading Elastic-plastic deformation near the contact surface of the circular disk under high loading T. Sawada & M. Horiike Department of Mechanical Systems Engineering Tokyo University of Agriculture and Technology,

More information

Stress analysis of a stepped bar

Stress analysis of a stepped bar Stress analysis of a stepped bar Problem Find the stresses induced in the axially loaded stepped bar shown in Figure. The bar has cross-sectional areas of A ) and A ) over the lengths l ) and l ), respectively.

More information

Finite element analysis of longitudinal debonding between fibre and matrix interface

Finite element analysis of longitudinal debonding between fibre and matrix interface Indian Journal of Engineering & Materials Sciences Vol. 11, February 2004, pp. 43-48 Finite element analysis of longitudinal debonding between fibre and matrix interface K Aslantaş & S Taşgetiren Department

More information

THEME A. Analysis of the elastic behaviour of La Aceña arch-gravity dam

THEME A. Analysis of the elastic behaviour of La Aceña arch-gravity dam THEME A Analysis of the elastic behaviour of La Aceña arch-gravity dam Gjorgi KOKALANOV, Professor, Faculty of Civil Eng., Skopje, Republic of Macedonia Ljubomir TANČEV, Professor, Faculty of Civil Eng.,

More information

ROTATING RING. Volume of small element = Rdθbt if weight density of ring = ρ weight of small element = ρrbtdθ. Figure 1 Rotating ring

ROTATING RING. Volume of small element = Rdθbt if weight density of ring = ρ weight of small element = ρrbtdθ. Figure 1 Rotating ring ROTATIONAL STRESSES INTRODUCTION High centrifugal forces are developed in machine components rotating at a high angular speed of the order of 100 to 500 revolutions per second (rps). High centrifugal force

More information

Study of Contact Behavior in the Pre-squeeze Stage of

Study of Contact Behavior in the Pre-squeeze Stage of Study of Contact Behavior in the Pre-squeeze Stage of Aluminum Alloy Resistance Spot Welding Li. Baoqing, Shan Ping Lian Jinrui, Hu Shengsun Tianjin University, Tianjin, P.R.C Abstract In this paper, an

More information

CONTRIBUTION TO EXTRUDATE SWELL FROM THE VELOCITY FACTOR IN NON- ISOTHERMAL EXTRUSION

CONTRIBUTION TO EXTRUDATE SWELL FROM THE VELOCITY FACTOR IN NON- ISOTHERMAL EXTRUSION Second International Conference on CFD in the Minerals and Process Industries CSIRO, Melbourne, Australia 6-8 December 1999 CONTRIBUTION TO EXTRUDATE SWELL FROM THE VELOCITY FACTOR IN NON- ISOTHERMAL EXTRUSION

More information

Mechanics PhD Preliminary Spring 2017

Mechanics PhD Preliminary Spring 2017 Mechanics PhD Preliminary Spring 2017 1. (10 points) Consider a body Ω that is assembled by gluing together two separate bodies along a flat interface. The normal vector to the interface is given by n

More information

#695 Numerical and experimental study on determination of the contact temperature in an industrial ironing operation

#695 Numerical and experimental study on determination of the contact temperature in an industrial ironing operation #695 Numerical and experimental study on determination of the contact temperature in an industrial ironing operation Esmeray Üstünyagiz a,*, Chris V. Nielsen a, Peter Christiansen a, Paulo A.F. Martins

More information

Finite-Element Analysis of Parts Stress State of Tight Joint Assembled by Press Fitting

Finite-Element Analysis of Parts Stress State of Tight Joint Assembled by Press Fitting Modern Mechanical Engineering, 04, 4, 98-06 Published Online November 04 in SciRes. http://www.scirp.org/journal/mme http://dx.doi.org/0.46/mme.04.4409 Finite-Element Analysis of Parts Stress State of

More information

MESH MODELING OF ANGLE-PLY LAMINATED COMPOSITE PLATES FOR DNS AND IPSAP

MESH MODELING OF ANGLE-PLY LAMINATED COMPOSITE PLATES FOR DNS AND IPSAP 16 TH INTERNATIONAL CONFERENCE ON COMPOSITE MATERIALS MESH MODELING OF ANGLE-PLY LAMINATED COMPOSITE PLATES FOR DNS AND IPSAP Wanil Byun*, Seung Jo Kim*, Joris Wismans** *Seoul National University, Republic

More information

Bulk Metal Forming II

Bulk Metal Forming II Bulk Metal Forming II Simulation Techniques in Manufacturing Technology Lecture 2 Laboratory for Machine Tools and Production Engineering Chair of Manufacturing Technology Prof. Dr.-Ing. Dr.-Ing. E.h.

More information

Elastic-Plastic Fracture Mechanics. Professor S. Suresh

Elastic-Plastic Fracture Mechanics. Professor S. Suresh Elastic-Plastic Fracture Mechanics Professor S. Suresh Elastic Plastic Fracture Previously, we have analyzed problems in which the plastic zone was small compared to the specimen dimensions (small scale

More information

Plane Strain Test for Metal Sheet Characterization

Plane Strain Test for Metal Sheet Characterization Plane Strain Test for Metal Sheet Characterization Paulo Flores 1, Felix Bonnet 2 and Anne-Marie Habraken 3 1 DIM, University of Concepción, Edmundo Larenas 270, Concepción, Chile 2 ENS - Cachan, Avenue

More information

An Analytical Model for Long Tube Hydroforming in a Square Cross-Section Die Considering Anisotropic Effects of the Material

An Analytical Model for Long Tube Hydroforming in a Square Cross-Section Die Considering Anisotropic Effects of the Material Journal of Stress Analysis Vol. 1, No. 2, Autumn Winter 2016-17 An Analytical Model for Long Tube Hydroforming in a Square Cross-Section Die Considering Anisotropic Effects of the Material H. Haghighat,

More information

2D Modeling of Elastic Wave Propagation in Solids Containing Closed Cracks with Friction

2D Modeling of Elastic Wave Propagation in Solids Containing Closed Cracks with Friction 2D Modeling of Elastic Wave Propagation in Solids Containing Closed Cracks with Friction S. Delrue 1, V. Aleshin 2, O. Bou Matar 2, K. Van Den Abeele 1 1 Wave Propagation & Signal Processing Research Group,

More information

Finite element analysis of indentation experiments J.M. Olaf Fraunhofer-Insitut fur Werkstoffmechanik, Wohlerstr. 11, D-W Freiburg, Germany

Finite element analysis of indentation experiments J.M. Olaf Fraunhofer-Insitut fur Werkstoffmechanik, Wohlerstr. 11, D-W Freiburg, Germany Finite element analysis of indentation experiments J.M. Olaf Fraunhofer-Insitut fur Werkstoffmechanik, Wohlerstr. 11, D-W- 7800 Freiburg, Germany ABSTRACT There are only a few methods suitable for a quantitative

More information

A multiscale framework for lubrication analysis of bearings with textured surface

A multiscale framework for lubrication analysis of bearings with textured surface A multiscale framework for lubrication analysis of bearings with textured surface *Leiming Gao 1), Gregory de Boer 2) and Rob Hewson 3) 1), 3) Aeronautics Department, Imperial College London, London, SW7

More information

An analysis of elasto-plastic sliding spherical asperity interaction

An analysis of elasto-plastic sliding spherical asperity interaction Wear 262 (2007) 210 219 An analysis of elasto-plastic sliding spherical asperity interaction Robert L. Jackson, Ravi S. Duvvuru, Hasnain Meghani, Manoj Mahajan Department of Mechanical Engineering, Auburn

More information

The plastic behaviour of silicon subjected to micro-indentation

The plastic behaviour of silicon subjected to micro-indentation JOURNAL OF MATERIALS SCIENCE 31 (1996) 5671-5676 The plastic behaviour of silicon subjected to micro-indentation L. ZHANG, M. MAHDI Centre for Advanced Materials Technology, Department of Mechanical and

More information

Effect of Strain Hardening on Unloading of a Deformable Sphere Loaded against a Rigid Flat A Finite Element Study

Effect of Strain Hardening on Unloading of a Deformable Sphere Loaded against a Rigid Flat A Finite Element Study Effect of Strain Hardening on Unloading of a Deformable Sphere Loaded against a Rigid Flat A Finite Element Study Biplab Chatterjee, Prasanta Sahoo 1 Department of Mechanical Engineering, Jadavpur University

More information

Development of X-FEM methodology and study on mixed-mode crack propagation

Development of X-FEM methodology and study on mixed-mode crack propagation Acta Mech. Sin. (2011) 27(3):406 415 DOI 10.1007/s10409-011-0436-x RESEARCH PAPER Development of X-FEM methodology and study on mixed-mode crack propagation Zhuo Zhuang Bin-Bin Cheng Received: 2 February

More information

Chapter 5 Torsion STRUCTURAL MECHANICS: CE203. Notes are based on Mechanics of Materials: by R. C. Hibbeler, 7th Edition, Pearson

Chapter 5 Torsion STRUCTURAL MECHANICS: CE203. Notes are based on Mechanics of Materials: by R. C. Hibbeler, 7th Edition, Pearson STRUCTURAL MECHANICS: CE203 Chapter 5 Torsion Notes are based on Mechanics of Materials: by R. C. Hibbeler, 7th Edition, Pearson Dr B. Achour & Dr Eng. K. El-kashif Civil Engineering Department, University

More information

3-D Finite Element Analysis of Instrumented Indentation of Transversely Isotropic Materials

3-D Finite Element Analysis of Instrumented Indentation of Transversely Isotropic Materials 3-D Finite Element Analysis of Instrumented Indentation of Transversely Isotropic Materials Abstract: Talapady S. Bhat and T. A. Venkatesh Department of Material Science and Engineering Stony Brook University,

More information

MECHANICS OF MATERIALS

MECHANICS OF MATERIALS 2009 The McGraw-Hill Companies, Inc. All rights reserved. Fifth SI Edition CHAPTER 3 MECHANICS OF MATERIALS Ferdinand P. Beer E. Russell Johnston, Jr. John T. DeWolf David F. Mazurek Torsion Lecture Notes:

More information

Optimization of contact stress distribution in interference fit

Optimization of contact stress distribution in interference fit 11 th World Congress on Structural and Multidisciplinary Optimization 7 th - 12 th, June 2015, Sydney Australia Optimization of contact stress distribution in interference fit Niels Leergaard Pedersen

More information

Modeling of Thermo-Mechanical Stresses in Twin-Roll Casting of Aluminum Alloys

Modeling of Thermo-Mechanical Stresses in Twin-Roll Casting of Aluminum Alloys Materials Transactions, Vol. 43, No. 2 (2002) pp. 214 to 221 c 2002 The Japan Institute of Metals Modeling of Thermo-Mechanical Stresses in Twin-Roll Casting of Aluminum Alloys Amit Saxena 1 and Yogeshwar

More information

MESO-SCALE MODELLING OF CONCRETE BEHAVIOUR UNDER TENSILE LOADING

MESO-SCALE MODELLING OF CONCRETE BEHAVIOUR UNDER TENSILE LOADING Congresso de Métodos Numéricos em Engenharia 2015 Lisboa, 29 de Junho a 2 de Julho 2015 c APMTAC, Portugal 2015 MESO-SCALE MODELLING OF CONCRETE BEHAVIOUR UNDER TENSILE LOADING C. Albino 1, D. Dias-da-Costa

More information

Proceedings of the ASME th International Conference on Ocean, Offshore and Arctic Engineering OMAE2016 June 19-24, 2016, Busan, South Korea

Proceedings of the ASME th International Conference on Ocean, Offshore and Arctic Engineering OMAE2016 June 19-24, 2016, Busan, South Korea Proceedings of the ASME 26 35th International Conference on Ocean, Offshore and Arctic Engineering OMAE26 June 9-24, 26, Busan, South Korea OMAE26-54554 LOCAL STRAIN AND STRESS CALCULATION METHODS OF IRREGULAR

More information

Instabilities and Dynamic Rupture in a Frictional Interface

Instabilities and Dynamic Rupture in a Frictional Interface Instabilities and Dynamic Rupture in a Frictional Interface Laurent BAILLET LGIT (Laboratoire de Géophysique Interne et Tectonophysique) Grenoble France laurent.baillet@ujf-grenoble.fr http://www-lgit.obs.ujf-grenoble.fr/users/lbaillet/

More information

Computational models of diamond anvil cell compression

Computational models of diamond anvil cell compression UDC 519.6 Computational models of diamond anvil cell compression A. I. Kondrat yev Independent Researcher, 5944 St. Alban Road, Pensacola, Florida 32503, USA Abstract. Diamond anvil cells (DAC) are extensively

More information

Forming parameters optimizations with drawing force and die stress in wire rod drawing using rotating die under Coulomb friction

Forming parameters optimizations with drawing force and die stress in wire rod drawing using rotating die under Coulomb friction Forming parameters optimizations with drawing force and die stress in wire rod drawing using rotating die under Coulomb friction Ing-Kiat Tiong, Un-Chin Chai, and Gow-Yi Tzou * Department of Mechanical

More information

Stress and Displacement Analysis of a Rectangular Plate with Central Elliptical Hole

Stress and Displacement Analysis of a Rectangular Plate with Central Elliptical Hole Stress and Displacement Analysis of a Rectangular Plate with Central Elliptical Hole Dheeraj Gunwant, J. P. Singh mailto.dheerajgunwant@gmail.com, jitenderpal2007@gmail.com, AIT, Rampur Abstract- A static

More information

Influence of impact velocity on transition time for V-notched Charpy specimen*

Influence of impact velocity on transition time for V-notched Charpy specimen* [ 溶接学会論文集第 35 巻第 2 号 p. 80s-84s (2017)] Influence of impact velocity on transition time for V-notched Charpy specimen* by Yasuhito Takashima** and Fumiyoshi Minami** This study investigated the influence

More information

Mechanics of Earthquakes and Faulting

Mechanics of Earthquakes and Faulting Mechanics of Earthquakes and Faulting www.geosc.psu.edu/courses/geosc508 Standard Solids and Fracture Fluids: Mechanical, Chemical Effects Effective Stress Dilatancy Hardening and Stability Mead, 1925

More information

FEM modeling of fiber reinforced composites

FEM modeling of fiber reinforced composites FEM modeling of fiber reinforced composites MSc Thesis Civil Engineering Elco Jongejans Delft, the Netherlands August MSc THESIS CIVIL ENGINEERING FEM modeling of fiber reinforced composites The use of

More information

Mathematical Background

Mathematical Background CHAPTER ONE Mathematical Background This book assumes a background in the fundamentals of solid mechanics and the mechanical behavior of materials, including elasticity, plasticity, and friction. A previous

More information

Examination in Damage Mechanics and Life Analysis (TMHL61) LiTH Part 1

Examination in Damage Mechanics and Life Analysis (TMHL61) LiTH Part 1 Part 1 1. (1p) Define the Kronecker delta and explain its use. The Kronecker delta δ ij is defined as δ ij = 0 if i j 1 if i = j and it is used in tensor equations to include (δ ij = 1) or "sort out" (δ

More information

Outline. Tensile-Test Specimen and Machine. Stress-Strain Curve. Review of Mechanical Properties. Mechanical Behaviour

Outline. Tensile-Test Specimen and Machine. Stress-Strain Curve. Review of Mechanical Properties. Mechanical Behaviour Tensile-Test Specimen and Machine Review of Mechanical Properties Outline Tensile test True stress - true strain (flow curve) mechanical properties: - Resilience - Ductility - Toughness - Hardness A standard

More information

Chapter 2 Finite Element Formulations

Chapter 2 Finite Element Formulations Chapter 2 Finite Element Formulations The governing equations for problems solved by the finite element method are typically formulated by partial differential equations in their original form. These are

More information

ME 2570 MECHANICS OF MATERIALS

ME 2570 MECHANICS OF MATERIALS ME 2570 MECHANICS OF MATERIALS Chapter III. Mechanical Properties of Materials 1 Tension and Compression Test The strength of a material depends on its ability to sustain a load without undue deformation

More information

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich UNIVERSITY OF SASKATCHEWAN ME 313.3 MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS For Marker s Use Only LAST NAME (printed): FIRST

More information

LIMIT LOAD OF A MASONRY ARCH BRIDGE BASED ON FINITE ELEMENT FRICTIONAL CONTACT ANALYSIS

LIMIT LOAD OF A MASONRY ARCH BRIDGE BASED ON FINITE ELEMENT FRICTIONAL CONTACT ANALYSIS 5 th GRACM International Congress on Computational Mechanics Limassol, 29 June 1 July, 2005 LIMIT LOAD OF A MASONRY ARCH BRIDGE BASED ON FINITE ELEMENT FRICTIONAL CONTACT ANALYSIS G.A. Drosopoulos I, G.E.

More information

A new method for acquiring true stress strain curves over a large range of strains using a tensile test and finite element method

A new method for acquiring true stress strain curves over a large range of strains using a tensile test and finite element method Available online at www.sciencedirect.com Mechanics of Materials 4 (28) 586 593 www.elsevier.com/locate/mechmat A new method for acquiring true stress strain curves over a large range of strains using

More information

Contact pressure distribution in joints formed by V-band clamps Simon M Barrans 1,a, Goodarz Khodabakhshi 1,b and Qiang Xu 1,c

Contact pressure distribution in joints formed by V-band clamps Simon M Barrans 1,a, Goodarz Khodabakhshi 1,b and Qiang Xu 1,c Contact pressure distribution in joints formed by V-band clamps Simon M Barrans 1,a, Goodarz Khodabakhshi 1,b and Qiang Xu 1,c 1 School of Computing and Engineering, University of Huddersfield, Queensgate,

More information

Design of structural components and radial-build for FFHR-d1

Design of structural components and radial-build for FFHR-d1 Japan-US Workshop on Fusion Power Plants and Related Advanced Technologies with participations from China and Korea February 26-28, 2013 at Kyoto University in Uji, JAPAN 1 Design of structural components

More information

On Springback Prediction In Stamping Of AHSS BIW Components Utilizing Advanced Material Models

On Springback Prediction In Stamping Of AHSS BIW Components Utilizing Advanced Material Models On Springback Prediction In Stamping Of AHSS BIW Components Utilizing Advanced Material Models Ming F. Shi and Alex A. Konieczny United States Steel Corporation Introduction Origin of Springback AHSS Springback

More information

Due Monday, September 14 th, 12:00 midnight

Due Monday, September 14 th, 12:00 midnight Due Monday, September 14 th, 1: midnight This homework is considering the analysis of plane and space (3D) trusses as discussed in class. A list of MatLab programs that were discussed in class is provided

More information

Mechanical Engineering Ph.D. Preliminary Qualifying Examination Solid Mechanics February 25, 2002

Mechanical Engineering Ph.D. Preliminary Qualifying Examination Solid Mechanics February 25, 2002 student personal identification (ID) number on each sheet. Do not write your name on any sheet. #1. A homogeneous, isotropic, linear elastic bar has rectangular cross sectional area A, modulus of elasticity

More information

Strength of Material. Shear Strain. Dr. Attaullah Shah

Strength of Material. Shear Strain. Dr. Attaullah Shah Strength of Material Shear Strain Dr. Attaullah Shah Shear Strain TRIAXIAL DEFORMATION Poisson's Ratio Relationship Between E, G, and ν BIAXIAL DEFORMATION Bulk Modulus of Elasticity or Modulus of Volume

More information

Design of Pressure Vessel Pads and Attachments To Minimize Global Stress Concentrations

Design of Pressure Vessel Pads and Attachments To Minimize Global Stress Concentrations Transactions, SMiRT 9, Toronto, August 007 Design of Pressure Vessel Pads and Attachments To Minimize Global Stress Concentrations Gordon S. Bjorkman ) ) Spent Fuel Storage and Transportation Division,

More information

Development and analysis for the large-scale tee-forming process

Development and analysis for the large-scale tee-forming process Journal of Materials Processing Technology 104 (2000) 265±270 Development and analysis for the large-scale tee-forming process Quang-Cherng Hsu a,*, Sio-Hou Lei b a Department of Mechanical Engineering,

More information

Fatigue Damage Development in a Steel Based MMC

Fatigue Damage Development in a Steel Based MMC Fatigue Damage Development in a Steel Based MMC V. Tvergaard 1,T.O/ rts Pedersen 1 Abstract: The development of fatigue damage in a toolsteel metal matrix discontinuously reinforced with TiC particulates

More information

A short review of continuum mechanics

A short review of continuum mechanics A short review of continuum mechanics Professor Anette M. Karlsson, Department of Mechanical ngineering, UD September, 006 This is a short and arbitrary review of continuum mechanics. Most of this material

More information

A slip-line solution to metal machining using a cutting tool with a step-type chip-breaker

A slip-line solution to metal machining using a cutting tool with a step-type chip-breaker Journal of Materials Processing Technology 79 (1998) 217 223 A slip-line solution to metal machining using a cutting tool with a step-type chip-breaker K.P. Maity *, N.S. Das Department of Mechanical Engineering,

More information