PARAMETER IDENTIFICATION, MODELING, AND SIMULATION OF A CART AND PENDULUM

Size: px
Start display at page:

Download "PARAMETER IDENTIFICATION, MODELING, AND SIMULATION OF A CART AND PENDULUM"

Transcription

1 PARAMETER IDENTIFICATION, MODELING, AND SIMULATION OF A CART AND PENDULUM Erin Bender Mechanical Engineering Erin.N.Bender@Rose-Hulman.edu ABSTRACT In this paper a freely rotating pendulum suspended from a cart that slides on two parallel rails is modeled. In order to create this model several system parameters had to e experimentally determined. These parameters include the rotational damping and coulom friction of the earings attaching the pendulum to the cart, as well as the linear damping and coulom friction of the linear earings which the cart slides on. The results from a simple experiment were examined to determine each parameter. For the rotational terms the pendulum, suspended from a stationary cart, is given an initial displacement. The system is then modeled and the measured displacement is compared to the prediction of the model. For the translational terms the cart was modeled as free to oscillate etween two springs in tension, the pendulum was omitted from this analysis. In each case, the simulations were performed using Dymola and Simulink computer packages and the difference etween the experiment and the model was minimized y varying the parameter to e identified. Values were otained for the rotational and linear damping, as well as the rotational and linear coulom friction, which caused the model to agree nicely with the experiment. Keywords: Modeling, Simulation, Cart and Pendulum, Simulink, Dymola INTRODUCTION For this project the cart and pendulum set-up in the Dynamic Systems and Controls La was utilized. The system itself is descried in further detail elow. The project goal is to create a model which accurately predicts oth the pendulum position and the cart position. Although a model of the system existed previous to this project, it had not een updated in quite some time. Therefore it was desirale to redetermine several system parameters, as they appear to have changed over time. These parameters were determined y conducting two simple experiments and comparing the results to the experiment. SYSTEM DESCRIPTION The system consists of a slender rod attached y way of two earings to a cart. The cart is mounted on four pillow lock linear earings, which slide along two parallel rails. The pendulum is free to swing elow the cart. If the pendulum is mounted aove the cart, the system is the conventional inverted pendulum system familiar in controls las everywhere. The input to the system is the voltage supplied to a DC motor. The motor then produces a torque, which is put through a series of gears and then transmitted to the

2 cart through a plastic chain. User input through a computer controls the input voltage. A system schematic can e seen in Fig. 1. Descriptors The following variales are used to descrie the ehavior of the system. θ displacement angle of the pendulum x displacement distance of the cart ω output velocity of the motor m ω output velocity of the rake motor Measured Parameters The following parameters were measured from the physical system. Tale 1: Measured System Parameters Parameter Value Description m c 4.609kg mass of the cart m kg mass of the pendulum l p p g,1 0.86m length of the pendulum r m radius of gear 1 t m thickness of gear 1 g,1 r 0.05m radius of gear g, t m thickness of gear g, r m hu radius of hu t 0.0m hu thickness of hu r m radius of gear 3 g,3 t m thickness of gear 3 g,3

3 Π α Π α Π Figure 1: System Schematic with Descriptors and Parameters Identified

4 Calculated Parameters The system parameters given in Tale were calculated from the physical system using Eq. (1), (), and (3).The mass moment of inertia of the pendulum was calculated using the measured mass and length of the pendulum and Eq. (1). It was not possile to physically remove the gears from the system in order to weigh them. It was therefore necessary to estimate the mass of each gear from measurale system quantities. The radius and thickness of each gear was measured, these data can e seen in Tale 1. Gears 1 and were assumed to e made of steel, while gear 3 was assumed to e made of aluminum, the specific weight of each sustance is given elow. The approximate mass of each gear was then computed using Eq. (). Finally the mass moment of inertia of each gear could e computed using Eq. (3). The results of oth of these computations can e seen in Tale. Mass moment of inertia of a slender rod-taken aout the end point: 1 (1) I O = ml 3 Mass of a cylinder: m = γπr t () kg where γ = 7860 for steel m 3 kg and γ = for aluminum 3 m Mass moment of inertia of a thin disk: 1 I mr G = (3) Tale : Calculated System Parameters Parameter Value Description I G, N m mass moment of inertia of the pendulum p rad sec m 0.075kg mass of gear 1 G,1 I G,1 6 N m mass moment of inertia of gear E rad sec m kg mass of gear G, I G, 5 N m mass moment of inertia of gear.086e rad sec m 0.775kg mass of the hu hu I hu 4 N m mass moment of inertia of the hu 5.478E rad sec I sprocket 4 N m mass moment of inertia of the sprocket 5.687E rad sec

5 m 0.069kg mass of gear 3 G,3 I G, E 6 N m mass moment of inertia of gear 3 rad sec Provided The following parameters were otained from the manufacturer s specifications we page [1]. Motor R, 0.739Ω armature resistance a m L, 45 µ H armature inductance a m J m c m K e, m K t, m 1.0E 4.094E N m rad sec 6 N m rad sec V RPM N m A moment of inertia viscous damping constant ack emf constant torque constant Brake Motor R, 1.10Ω armature resistance a L, 100 µ H armature inductance a J c K e, K t, N m 0.19 rad sec 7 N m 7.330E rad sec V RPM m A N moment of inertia viscous damping constant ack emf constant for the motor used as a rake torque constant for the motor used as a rake

6 SYSTEM IDENTIFICATION Rotational Damping Pendulum Encoder Caliration Experimental Set-Up In order to determine the rotational damping of the earings that attach the pendulum to the cart, a simple experiment was performed. The cart was held stationary, the pendulum was given an initial displacement from the horizontal, an encoder was used to measure θ, and the data was acquired y a data acquisition system. A diagram of this experimental set-up can e seen in Fig.. Π Figure : Rotational Damping Experimental Set-Up Model Development Initially the pendulum was modeled assuming only rotational damping was present. For this system Eq. (4) was derived as the equation of motion. mgl (4) p J & θ + & rθ = sin( θ ) The est value for the damping will provide the smallest difference etween the experimental data and the theoretical Dymola simulation results. To find this value a cost function, defined y Eq. (5), was used. This cost function is the sumsquared error etween the experimental and theoretical data. J = θ θ (5) ( ) theoretical exp erimental The Dymola simulation was run in Simulink with several different values of r, and J was calculated each time. A plot of several iterations of this process can e seen in Fig. 3. The damping constant which produced the lowest error value is N m r = rad s

7 0.4 sum squared error damping coefficient Figure 3: Minimization of System Error for Rotational Damping After minimizing the error with only rotational damping, coulom friction is added to the model. For this more complex system, Eq. (6) was derived as the equation of motion. In order to accurately model the coulom friction, that is to make it always negative, the coulom friction constant was multiplied y the sign of the angular velocity. In doing this, if the angular velocity is negative, a negative sign will e added to the coulom friction term making it positive. However, if the angular velocity is positive, the coulom friction term will remain negative. & θ & mgl (6) p J + θ sin( θ ) c sign( & r = r θ ) The values of r and c r that minimize the error etween Eq. (6) and the N m experimental data are c r = 0 and r = Thus, the pendulum is most rad s accurately modeled with rotational damping and no coulom friction. Simulation Settings The experimental data was taken y an encoder with a sample frequency of 100 Hz. In order to easily calculate the error etween the experimental data and the Simulink output it was desired that the Simulink model also run at a sample frequency of 100 Hz, that is a step size of 0.01 seconds. This was accomplished y making Simulink solve the model with a fixed time step size ODE solver, as opposed to a variale time step solver. For this particular simulation, a fourth order Runga-Kutta solver was used.

8 Simulation Results N m After running the model several times a value of r = was rad s found to minimize the error. A plot of the Simulink output and the experimental data for the final value of the rotational damping constant can e seen in Figure. Linear Damping Figure 4: Simulink and Experimental Data Experimental Set-Up In order to determine the linear damping of the cart, a spring was hooked to either end of the cart. The other end of each spring was then hooked into a clamp which was rigidly attached to the frame of the system. The cart was then deflected an initial distance to one side and released, while an encoder was used to measure the position of the cart. It was not possile to measure the position of the cart directly, ut there was an encoder set-up to measure the output from a tachometer attached to the motor. For this reason the motor and the rake motor were left in the system, and the data from the tachometer was converted to give the position of the cart.. A diagram of this experimental set-up can e seen in Fig. 5.

9 Π α α Π Figure 5: Linear Damping Experimental Set-Up Spring Constant Determination After the experiment was finished each spring was hung from a rigid support and various weights were hung on the free end. The deflection of the spring in centimeters was measured for each weight used. These values were then plotted in MatLa and the polyfit and polyval commands were used to determine a linear approximation of the data. These approximations can e seen elow as Eq. (7) and (8). In each case the coefficient for the deflection term is the spring constant. Thus K1 = N m and K = N m. F 1 = x (7) F = 130.1x (8) A plot of the experimental data and the linear approximation for each spring can e seen elow in Figures 6 and 7.

10 Figure 6: Determination of Spring Constant One Figure 7: Determination of Spring Constant Two Model Development Initially the cart was modeled assuming that the moments of inertia of the gears were not negligile, and that the moments of inertia provided y the manufacturer for the motors were correct. The springs connecting the cart to the frame were assumed to e operating in their linear regions, and each spring was initially deflected 0.095m. This yielded Eq. (9) as the equation of motion.

11 [ m + m ]& x + [ c + ] x& + K x ) K (0.095 x) + c sign( x& ) 0 c inertial where and c m inertial inertial inertial ( c = L 1 ( L = I g, 1 I g, (I g,3 + J m + J ) r = + r m 1 + c ) r + r1 r3 This simulation was run in Simulink and plotted against the experimental data, see Fig. 8. r r 1 3 (9) Figure 8: Initial Model for Linear Damping Terms Oviously Eq. (9) is not a very good model of the system. The most ovious reason for this discrepancy is that the moments of inertia for the motors are not correct. Another possiility is that the control system is acting in some way which is not understood at this time. A new model for the system was derived and can e seen in Eq. (10). This time the moments of inertia for the gears were assumed to e negligile, as they are very small and can e accounted for in the added inertial term. Also the coulom friction was assumed to e 10 N since that is force found in an informal experiment and it didn t produce a noticeale effect on the simulation output. A spring scale was attached to the cart and used to pull the cart at a constant velocity, as this was done the scale read approximately 10 N.

12 ( m + m )& x + x& c inertial L + K1 ( x ) K (0.095 x) + 10 = 0 (10) where m inertial is an input eing solved for The est values for the damping and the additional mass of the system will provide the smallest difference etween the experimental data and the theoretical Dymola simulation data. To find this value a cost function was used again. This cost function is the sum-squared error etween the experimental data and theoretical results and can e seen in Eq. (5). First the linear damping term was changed while the inertial mass was held constant at 6.8. A plot of the various values for oth the linear damping and the error can e seen in Fig. 9. Figure 9: Minimization of System Error with Inertial Mass Held Constant Next the inertial mass term was changed while the linear damping was held at 51. As aove a plot of inertial mass and the system error can e seen in Fig. 10. Figure 10: Minimization of System Error with Linear Damping Held Constant

13 Simulation Settings The settings are the same as they were for the rotational damping simulation. Simulation Results After running the simulation several times final values of l N m = 48 for rad s the linear damping and m inertial = 6. 8kg for the added inertial mass of the system were found to minimize the error. A plot of the Simulink output and the experimental data for these values can e seen in Fig. 11. Figure 11: Final Model for Linear Damping Terms

14 SUMMARY OF IDENTIFIED PARAMETERS The following parameter values were experimentally determined. Tale 3: Experimentally Determined Parameters N m rotational damping of the pendulum earings rad s c r 0 coulom friction of the pendulum earings K N m spring constant of spring 1 K 130.1N m spring constant of spring N m initial linear damping of the pendulum earings 48 rad s m 6.8kg inertial final inertial mass of the system N m final linear damping of the pendulum earings 51 rad s r l l CONCLUSIONS Values were otained for all of the parameters which were to e experimentally determined and can e seen in Tale 3 aove. The model for the rotational damping of pendulum earings matched the experimental data with no additional changes to the model. With the linear model, however, it was found that inertial mass needed to e added to the system in order for the model and the experiment to agree. After this additional mass was included in the model, the simulation and the experiment matched quite well. This indicates that further work needs to e done in identifying the parameters of the system and understanding the control system. FURTHER WORK Experimentally identify the parameters of the motors inertial mass armature resistance armature inductance viscous damping constant Construct and test a DAE model of the entire closed loop system controller in the loop the pendulum inverted Construct and train a neural net model ACKNOWLEDGEMENTS Ben Howe for his help numerous times in setting up and running experiments. REFERENCES [1]

15 APPENDIX A: SIMULINK MODEL AND ASSOCIATED DYMOLA CODE Rotational Damping Model:.03 [r] tv ar 1 c[r] c Dym olablock Scope theta T o Workspace egin RotaDamp.mo class RotaDamp parameter Real m=0.1791; parameter Real L=0.86; parameter Real g=9.81; parameter Real I=0.044; input Real ; input Real c; Real theta; Real f; output Real tvar; equation tvar = theta; der(theta) = f; I*der(f) + *f + m*g*l/*sin(theta) + c*f = 0; end RotaDamp end RotaDamp.mo

16 Initial Linear Damping Model: 35 L linear dam ping x xout 10 coulom friction c L T o Workspace egin LinearDamp.mo class LinearDamp parameter Real mc=4.609; parameter Real Ig1=3.698E-6; parameter Real Ig=5.687E-4; parameter Real Ig3=4.406E-6; parameter Real J=0.19; parameter Real Jm=1.E-4; parameter Real K1=1197.3; parameter Real K=130.1; parameter Real c=7.330e-7; parameter Real cm=.094e-6; parameter Real r1=0.0164; parameter Real r=0.05; parameter Real r3=0.0181; Dym ol abl ock Scope Real tempx(start=0.1146); Real TotalMass; Real TotalDamp; Real coulom; Real f; input Real L; input Real cl; output Real x(start=0.1146); equation TotalMass = mc + *(Ig1 + Ig)/r1 + (*Ig3 + Jm + J)*r/(r1*r3); TotalDamp = (cm + c)*r/(r1*r3) + L; tempx = x; cou = cl*sign(f); f = der(tempx); TotalMass*der(f) + TotalDamp*f + K1*(x ) - K*( x) + cou = 0; end LinearDampend LinearDamp.mo

17 Modified Linear Damping Model: 6.8 m inert inertial m ass x xout 48 linear dam ping L T o Workspace egin LinearDampMod.mo model LinearDampMod parameter Real mc=4.609; parameter Real K1=1197.3; parameter Real K=130.1; Dym olablock Scope Real tempx; Real f; input Real minert; input Real L; output Real x; equation tempx = x; f = der(tempx); (mc + minert)*der(f) + L*f + K1*(x ) - K*( x) + 10 = 0; end LinearDampMod end LinearDampMod.mo

18 APPENDIX B: MATLAB CODE Rotational Damping Model: egin RotaDampCode.m % Import the output of the Simulink model (theta) and the time vector (tout) from the workspace % Plot the Simulink output vs. experimental data figure plot(tangle,angle,tout,theta,':') axis([0,5,-0.4,0.3]) xlael('time (sec.)') ylael('theta (rad.)') grid legend('experimental Data','Theoretical Data') % Calculate the squared error and plot it for several values of r % Output the sum squared error for easy reference Err = (angle - theta).^; J = sum(err) % Vectors of the damping coefficient input to the simulink model % and the output sum squared error input = [ ]; outputj = [ ]; figure plot(input,outputj,'*') axis([0.034,0.043,0.35,0.41]) xlael('damping coefficient') ylael('sum squared error') end RotaDampCode.m Linear Damping Model: egin SpringConstants.m % Calculation of Spring Constants % the masses are in ls the force is in Newtons mass = [ ]; force = mass.*0.454.*9.81; % Spring 1 Length1 = [ ]; Deflec1 = Length1-0.11;

19 [P1] = polyfit(deflec1, force, 1) y1 = polyval(p1, Deflec1); % plot the experimental data points and the linear approximation % for the deflection of spring 1 figure plot(deflec1,force,'*',deflec1,y1) grid xlael('deflection (m)') ylael('force (N)') axis([0,0.06,0,80]) % Spring Length = [ ]; Deflec = Length-0.15; [P] = polyfit(deflec, force, 1) y = polyval(p, Deflec); % plot the experimental data points and the linear approximation % for the deflection of spring figure plot(deflec,force,'*',deflec,y) grid xlael('deflection (m)') ylael('force (N)') axis([0,0.06,0,80]) end SpringConstants.m eginlineardampcode.m pos = exp.*0.054; time = [0:0.01:1.08]; % Import the output of the Simulink model (xout) and the time vector (tout) from % the workspace plot the Simulink output vs. experimental data plot(time,pos,'.',tout,xout) xlael('time (sec.)') ylael('position (m.)') grid legend('experimental Data','Simulation Results') % Calculate the squared error and plot it % Output the sum squared error for easy reference J = (pos - xout).^; sum(j) endlinear DampCode.m

Section 8.5. z(t) = be ix(t). (8.5.1) Figure A pendulum. ż = ibẋe ix (8.5.2) (8.5.3) = ( bẋ 2 cos(x) bẍ sin(x)) + i( bẋ 2 sin(x) + bẍ cos(x)).

Section 8.5. z(t) = be ix(t). (8.5.1) Figure A pendulum. ż = ibẋe ix (8.5.2) (8.5.3) = ( bẋ 2 cos(x) bẍ sin(x)) + i( bẋ 2 sin(x) + bẍ cos(x)). Difference Equations to Differential Equations Section 8.5 Applications: Pendulums Mass-Spring Systems In this section we will investigate two applications of our work in Section 8.4. First, we will consider

More information

Lab 6a: Pole Placement for the Inverted Pendulum

Lab 6a: Pole Placement for the Inverted Pendulum Lab 6a: Pole Placement for the Inverted Pendulum Idiot. Above her head was the only stable place in the cosmos, the only refuge from the damnation of the Panta Rei, and she guessed it was the Pendulum

More information

AP Physics. Harmonic Motion. Multiple Choice. Test E

AP Physics. Harmonic Motion. Multiple Choice. Test E AP Physics Harmonic Motion Multiple Choice Test E A 0.10-Kg block is attached to a spring, initially unstretched, of force constant k = 40 N m as shown below. The block is released from rest at t = 0 sec.

More information

TOPIC E: OSCILLATIONS EXAMPLES SPRING Q1. Find general solutions for the following differential equations:

TOPIC E: OSCILLATIONS EXAMPLES SPRING Q1. Find general solutions for the following differential equations: TOPIC E: OSCILLATIONS EXAMPLES SPRING 2019 Mathematics of Oscillating Systems Q1. Find general solutions for the following differential equations: Undamped Free Vibration Q2. A 4 g mass is suspended by

More information

Engineering Mechanics Prof. U. S. Dixit Department of Mechanical Engineering Indian Institute of Technology, Guwahati Introduction to vibration

Engineering Mechanics Prof. U. S. Dixit Department of Mechanical Engineering Indian Institute of Technology, Guwahati Introduction to vibration Engineering Mechanics Prof. U. S. Dixit Department of Mechanical Engineering Indian Institute of Technology, Guwahati Introduction to vibration Module 15 Lecture 38 Vibration of Rigid Bodies Part-1 Today,

More information

Physics 201 Exam 3 (Monday, November 5) Fall 2012 (Saslow)

Physics 201 Exam 3 (Monday, November 5) Fall 2012 (Saslow) Physics 201 Exam 3 (Monday, November 5) Fall 2012 (Saslow) Name (printed) Lab Section(+2 pts) Name (signed as on ID) Multiple choice Section. Circle the correct answer. No work need be shown and no partial

More information

Lab 3: Quanser Hardware and Proportional Control

Lab 3: Quanser Hardware and Proportional Control Lab 3: Quanser Hardware and Proportional Control The worst wheel of the cart makes the most noise. Benjamin Franklin 1 Objectives The goal of this lab is to: 1. familiarize you with Quanser s QuaRC tools

More information

Kinematics, Dynamics, and Vibrations FE Review Session. Dr. David Herrin March 27, 2012

Kinematics, Dynamics, and Vibrations FE Review Session. Dr. David Herrin March 27, 2012 Kinematics, Dynamics, and Vibrations FE Review Session Dr. David Herrin March 7, 0 Example A 0 g ball is released vertically from a height of 0 m. The ball strikes a horizontal surface and bounces back.

More information

Lab 5a: Pole Placement for the Inverted Pendulum

Lab 5a: Pole Placement for the Inverted Pendulum Lab 5a: Pole Placement for the Inverted Pendulum November 1, 2011 1 Purpose The objective of this lab is to achieve simultaneous control of both the angular position of the pendulum and horizontal position

More information

DC Motor Position: System Modeling

DC Motor Position: System Modeling 1 of 7 01/03/2014 22:07 Tips Effects TIPS ABOUT BASICS INDEX NEXT INTRODUCTION CRUISE CONTROL MOTOR SPEED MOTOR POSITION SUSPENSION INVERTED PENDULUM SYSTEM MODELING ANALYSIS DC Motor Position: System

More information

Unit 7: Oscillations

Unit 7: Oscillations Text: Chapter 15 Unit 7: Oscillations NAME: Problems (p. 405-412) #1: 1, 7, 13, 17, 24, 26, 28, 32, 35 (simple harmonic motion, springs) #2: 45, 46, 49, 51, 75 (pendulums) Vocabulary: simple harmonic motion,

More information

Physics 41 HW Set 1 Chapter 15 Serway 8 th ( 7 th )

Physics 41 HW Set 1 Chapter 15 Serway 8 th ( 7 th ) Conceptual Q: 4 (7), 7 (), 8 (6) Physics 4 HW Set Chapter 5 Serway 8 th ( 7 th ) Q4(7) Answer (c). The equilibrium position is 5 cm below the starting point. The motion is symmetric about the equilibrium

More information

Plane Motion of Rigid Bodies: Forces and Accelerations

Plane Motion of Rigid Bodies: Forces and Accelerations Plane Motion of Rigid Bodies: Forces and Accelerations Reference: Beer, Ferdinand P. et al, Vector Mechanics for Engineers : Dynamics, 8 th Edition, Mc GrawHill Hibbeler R.C., Engineering Mechanics: Dynamics,

More information

Chapter 14 Periodic Motion

Chapter 14 Periodic Motion Chapter 14 Periodic Motion 1 Describing Oscillation First, we want to describe the kinematical and dynamical quantities associated with Simple Harmonic Motion (SHM), for example, x, v x, a x, and F x.

More information

ECEN 420 LINEAR CONTROL SYSTEMS. Lecture 6 Mathematical Representation of Physical Systems II 1/67

ECEN 420 LINEAR CONTROL SYSTEMS. Lecture 6 Mathematical Representation of Physical Systems II 1/67 1/67 ECEN 420 LINEAR CONTROL SYSTEMS Lecture 6 Mathematical Representation of Physical Systems II State Variable Models for Dynamic Systems u 1 u 2 u ṙ. Internal Variables x 1, x 2 x n y 1 y 2. y m Figure

More information

Oscillations. Oscillations and Simple Harmonic Motion

Oscillations. Oscillations and Simple Harmonic Motion Oscillations AP Physics C Oscillations and Simple Harmonic Motion 1 Equilibrium and Oscillations A marble that is free to roll inside a spherical bowl has an equilibrium position at the bottom of the bowl

More information

CHAPTER 12 OSCILLATORY MOTION

CHAPTER 12 OSCILLATORY MOTION CHAPTER 1 OSCILLATORY MOTION Before starting the discussion of the chapter s concepts it is worth to define some terms we will use frequently in this chapter: 1. The period of the motion, T, is the time

More information

Coupled Drive Apparatus Modelling and Simulation

Coupled Drive Apparatus Modelling and Simulation University of Ljubljana Faculty of Electrical Engineering Victor Centellas Gil Coupled Drive Apparatus Modelling and Simulation Diploma thesis Menthor: prof. dr. Maja Atanasijević-Kunc Ljubljana, 2015

More information

Mechatronics. MANE 4490 Fall 2002 Assignment # 1

Mechatronics. MANE 4490 Fall 2002 Assignment # 1 Mechatronics MANE 4490 Fall 2002 Assignment # 1 1. For each of the physical models shown in Figure 1, derive the mathematical model (equation of motion). All displacements are measured from the static

More information

Mechatronic System Case Study: Rotary Inverted Pendulum Dynamic System Investigation

Mechatronic System Case Study: Rotary Inverted Pendulum Dynamic System Investigation Mechatronic System Case Study: Rotary Inverted Pendulum Dynamic System Investigation Dr. Kevin Craig Greenheck Chair in Engineering Design & Professor of Mechanical Engineering Marquette University K.

More information

Physics 2210 Homework 18 Spring 2015

Physics 2210 Homework 18 Spring 2015 Physics 2210 Homework 18 Spring 2015 Charles Jui April 12, 2015 IE Sphere Incline Wording A solid sphere of uniform density starts from rest and rolls without slipping down an inclined plane with angle

More information

Harmonic Oscillator. Mass-Spring Oscillator Resonance The Pendulum. Physics 109 Experiment Number 12

Harmonic Oscillator. Mass-Spring Oscillator Resonance The Pendulum. Physics 109 Experiment Number 12 Harmonic Oscillator Mass-Spring Oscillator Resonance The Pendulum Physics 109 Experiment Number 12 Outline Simple harmonic motion The vertical mass-spring system Driven oscillations and resonance The pendulum

More information

In-Class Problems 30-32: Moment of Inertia, Torque, and Pendulum: Solutions

In-Class Problems 30-32: Moment of Inertia, Torque, and Pendulum: Solutions MASSACHUSETTS INSTITUTE OF TECHNOLOGY Department of Physics Physics 8.01 TEAL Fall Term 004 In-Class Problems 30-3: Moment of Inertia, Torque, and Pendulum: Solutions Problem 30 Moment of Inertia of a

More information

Moment of Inertia Race

Moment of Inertia Race Review Two points, A and B, are on a disk that rotates with a uniform speed about an axis. Point A is closer to the axis than point B. Which of the following is NOT true? 1. Point B has the greater tangential

More information

Real-Time Implementation of a LQR-Based Controller for the Stabilization of a Double Inverted Pendulum

Real-Time Implementation of a LQR-Based Controller for the Stabilization of a Double Inverted Pendulum Proceedings of the International MultiConference of Engineers and Computer Scientists 017 Vol I,, March 15-17, 017, Hong Kong Real-Time Implementation of a LQR-Based Controller for the Stabilization of

More information

Laboratory 11 Control Systems Laboratory ECE3557. State Feedback Controller for Position Control of a Flexible Joint

Laboratory 11 Control Systems Laboratory ECE3557. State Feedback Controller for Position Control of a Flexible Joint Laboratory 11 State Feedback Controller for Position Control of a Flexible Joint 11.1 Objective The objective of this laboratory is to design a full state feedback controller for endpoint position control

More information

Final Examination Thursday May Please initial the statement below to show that you have read it

Final Examination Thursday May Please initial the statement below to show that you have read it EN40: Dynamics and Vibrations Final Examination Thursday May 0 010 Division of Engineering rown University NME: General Instructions No collaboration of any kind is permitted on this examination. You may

More information

PHYSICS 221, FALL 2011 EXAM #2 SOLUTIONS WEDNESDAY, NOVEMBER 2, 2011

PHYSICS 221, FALL 2011 EXAM #2 SOLUTIONS WEDNESDAY, NOVEMBER 2, 2011 PHYSICS 1, FALL 011 EXAM SOLUTIONS WEDNESDAY, NOVEMBER, 011 Note: The unit vectors in the +x, +y, and +z directions of a right-handed Cartesian coordinate system are î, ĵ, and ˆk, respectively. In this

More information

System Parameters and Frequency Response MAE 433 Spring 2012 Lab 2

System Parameters and Frequency Response MAE 433 Spring 2012 Lab 2 System Parameters and Frequency Response MAE 433 Spring 2012 Lab 2 Prof. Rowley, Prof. Littman AIs: Brandt Belson, Jonathan Tu Technical staff: Jonathan Prévost Princeton University Feb. 21-24, 2012 1

More information

Rotary Inverted Pendulum

Rotary Inverted Pendulum Rotary Inverted Pendulum Eric Liu 1 Aug 2013 1 1 State Space Derivations 1.1 Electromechanical Derivation Consider the given diagram. We note that the voltage across the motor can be described by: e b

More information

Rotational Dynamics continued

Rotational Dynamics continued Chapter 9 Rotational Dynamics continued 9.4 Newton s Second Law for Rotational Motion About a Fixed Axis ROTATIONAL ANALOG OF NEWTON S SECOND LAW FOR A RIGID BODY ROTATING ABOUT A FIXED AXIS I = ( mr 2

More information

FEEDBACK CONTROL SYSTEMS

FEEDBACK CONTROL SYSTEMS FEEDBAC CONTROL SYSTEMS. Control System Design. Open and Closed-Loop Control Systems 3. Why Closed-Loop Control? 4. Case Study --- Speed Control of a DC Motor 5. Steady-State Errors in Unity Feedback Control

More information

AP Physics C: Rotation II. (Torque and Rotational Dynamics, Rolling Motion) Problems

AP Physics C: Rotation II. (Torque and Rotational Dynamics, Rolling Motion) Problems AP Physics C: Rotation II (Torque and Rotational Dynamics, Rolling Motion) Problems 1980M3. A billiard ball has mass M, radius R, and moment of inertia about the center of mass I c = 2 MR²/5 The ball is

More information

Topic 1: Newtonian Mechanics Energy & Momentum

Topic 1: Newtonian Mechanics Energy & Momentum Work (W) the amount of energy transferred by a force acting through a distance. Scalar but can be positive or negative ΔE = W = F! d = Fdcosθ Units N m or Joules (J) Work, Energy & Power Power (P) the

More information

( ) Physics 201, Final Exam, Fall 2006 PRACTICE EXAMINATION Answer Key. The next three problems refer to the following situation:

( ) Physics 201, Final Exam, Fall 2006 PRACTICE EXAMINATION Answer Key. The next three problems refer to the following situation: Physics 201, Final Exam, Fall 2006 PRACTICE EXAMINATION Answer Key The next three problems refer to the following situation: Two masses, m 1 and m 2, m 1 > m 2, are suspended by a massless rope over a

More information

16.07 Dynamics. Problem Set 10

16.07 Dynamics. Problem Set 10 NAME :..................... Massachusetts Institute of Technology 16.07 Dynamics Problem Set 10 Out date: Nov. 7, 2007 Due date: Nov. 14, 2007 Problem 1 Problem 2 Problem 3 Problem 4 Study Time Time Spent

More information

1. Replace the given system of forces acting on a body as shown in figure 1 by a single force and couple acting at the point A.

1. Replace the given system of forces acting on a body as shown in figure 1 by a single force and couple acting at the point A. Code No: Z0321 / R07 Set No. 1 I B.Tech - Regular Examinations, June 2009 CLASSICAL MECHANICS ( Common to Mechanical Engineering, Chemical Engineering, Mechatronics, Production Engineering and Automobile

More information

Chapter 12. Recall that when a spring is stretched a distance x, it will pull back with a force given by: F = -kx

Chapter 12. Recall that when a spring is stretched a distance x, it will pull back with a force given by: F = -kx Chapter 1 Lecture Notes Chapter 1 Oscillatory Motion Recall that when a spring is stretched a distance x, it will pull back with a force given by: F = -kx When the mass is released, the spring will pull

More information

28. Pendulum phase portrait Draw the phase portrait for the pendulum (supported by an inextensible rod)

28. Pendulum phase portrait Draw the phase portrait for the pendulum (supported by an inextensible rod) 28. Pendulum phase portrait Draw the phase portrait for the pendulum (supported by an inextensible rod) θ + ω 2 sin θ = 0. Indicate the stable equilibrium points as well as the unstable equilibrium points.

More information

MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.

MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question. Exam Name MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question. 1) A 4.8-kg block attached to a spring executes simple harmonic motion on a frictionless

More information

Investigation of a Ball Screw Feed Drive System Based on Dynamic Modeling for Motion Control

Investigation of a Ball Screw Feed Drive System Based on Dynamic Modeling for Motion Control Investigation of a Ball Screw Feed Drive System Based on Dynamic Modeling for Motion Control Yi-Cheng Huang *, Xiang-Yuan Chen Department of Mechatronics Engineering, National Changhua University of Education,

More information

Rotary Motion Servo Plant: SRV02. Rotary Experiment #01: Modeling. SRV02 Modeling using QuaRC. Student Manual

Rotary Motion Servo Plant: SRV02. Rotary Experiment #01: Modeling. SRV02 Modeling using QuaRC. Student Manual Rotary Motion Servo Plant: SRV02 Rotary Experiment #01: Modeling SRV02 Modeling using QuaRC Student Manual SRV02 Modeling Laboratory Student Manual Table of Contents 1. INTRODUCTION...1 2. PREREQUISITES...1

More information

Rotational Mechanics Part III Dynamics. Pre AP Physics

Rotational Mechanics Part III Dynamics. Pre AP Physics Rotational Mechanics Part III Dynamics Pre AP Physics We have so far discussed rotational kinematics the description of rotational motion in terms of angle, angular velocity and angular acceleration and

More information

SRV02-Series Rotary Experiment # 1. Position Control. Student Handout

SRV02-Series Rotary Experiment # 1. Position Control. Student Handout SRV02-Series Rotary Experiment # 1 Position Control Student Handout SRV02-Series Rotary Experiment # 1 Position Control Student Handout 1. Objectives The objective in this experiment is to introduce the

More information

!T = 2# T = 2! " The velocity and acceleration of the object are found by taking the first and second derivative of the position:

!T = 2# T = 2!  The velocity and acceleration of the object are found by taking the first and second derivative of the position: A pendulum swinging back and forth or a mass oscillating on a spring are two examples of (SHM.) SHM occurs any time the position of an object as a function of time can be represented by a sine wave. We

More information

Rigid bodies - general theory

Rigid bodies - general theory Rigid bodies - general theory Kinetic Energy: based on FW-26 Consider a system on N particles with all their relative separations fixed: it has 3 translational and 3 rotational degrees of freedom. Motion

More information

CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5

CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5 1 / 36 CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5 Prof. Albert S. Kim Civil and Environmental Engineering, University of Hawaii at Manoa Date: 2 / 36 EQUATIONS OF MOTION: ROTATION

More information

Harmonic Oscillator. Outline. Oscillatory Motion or Simple Harmonic Motion. Oscillatory Motion or Simple Harmonic Motion

Harmonic Oscillator. Outline. Oscillatory Motion or Simple Harmonic Motion. Oscillatory Motion or Simple Harmonic Motion Harmonic Oscillator Mass-Spring Oscillator Resonance The Pendulum Physics 109, Class Period 13 Experiment Number 11 in the Physics 121 Lab Manual (page 65) Outline Simple harmonic motion The vertical mass-spring

More information

2.4 Harmonic Oscillator Models

2.4 Harmonic Oscillator Models 2.4 Harmonic Oscillator Models In this section we give three important examples from physics of harmonic oscillator models. Such models are ubiquitous in physics, but are also used in chemistry, biology,

More information

Quanser NI-ELVIS Trainer (QNET) Series: QNET Experiment #02: DC Motor Position Control. DC Motor Control Trainer (DCMCT) Student Manual

Quanser NI-ELVIS Trainer (QNET) Series: QNET Experiment #02: DC Motor Position Control. DC Motor Control Trainer (DCMCT) Student Manual Quanser NI-ELVIS Trainer (QNET) Series: QNET Experiment #02: DC Motor Position Control DC Motor Control Trainer (DCMCT) Student Manual Table of Contents 1 Laboratory Objectives1 2 References1 3 DCMCT Plant

More information

Human Arm. 1 Purpose. 2 Theory. 2.1 Equation of Motion for a Rotating Rigid Body

Human Arm. 1 Purpose. 2 Theory. 2.1 Equation of Motion for a Rotating Rigid Body Human Arm Equipment: Capstone, Human Arm Model, 45 cm rod, sensor mounting clamp, sensor mounting studs, 2 cord locks, non elastic cord, elastic cord, two blue pasport force sensors, large table clamps,

More information

Rotational motion problems

Rotational motion problems Rotational motion problems. (Massive pulley) Masses m and m 2 are connected by a string that runs over a pulley of radius R and moment of inertia I. Find the acceleration of the two masses, as well as

More information

is acting on a body of mass m = 3.0 kg and changes its velocity from an initial

is acting on a body of mass m = 3.0 kg and changes its velocity from an initial PHYS 101 second major Exam Term 102 (Zero Version) Q1. A 15.0-kg block is pulled over a rough, horizontal surface by a constant force of 70.0 N acting at an angle of 20.0 above the horizontal. The block

More information

a) Find the equation of motion of the system and write it in matrix form.

a) Find the equation of motion of the system and write it in matrix form. .003 Engineering Dynamics Problem Set Problem : Torsional Oscillator Two disks of radius r and r and mass m and m are mounted in series with steel shafts. The shaft between the base and m has length L

More information

Concept Question: Normal Force

Concept Question: Normal Force Concept Question: Normal Force Consider a person standing in an elevator that is accelerating upward. The upward normal force N exerted by the elevator floor on the person is 1. larger than 2. identical

More information

Rotation. PHYS 101 Previous Exam Problems CHAPTER

Rotation. PHYS 101 Previous Exam Problems CHAPTER PHYS 101 Previous Exam Problems CHAPTER 10 Rotation Rotational kinematics Rotational inertia (moment of inertia) Kinetic energy Torque Newton s 2 nd law Work, power & energy conservation 1. Assume that

More information

Solution Only gravity is doing work. Since gravity is a conservative force mechanical energy is conserved:

Solution Only gravity is doing work. Since gravity is a conservative force mechanical energy is conserved: 8) roller coaster starts with a speed of 8.0 m/s at a point 45 m above the bottom of a dip (see figure). Neglecting friction, what will be the speed of the roller coaster at the top of the next slope,

More information

CEE 271: Applied Mechanics II, Dynamics Lecture 27: Ch.18, Sec.1 5

CEE 271: Applied Mechanics II, Dynamics Lecture 27: Ch.18, Sec.1 5 1 / 42 CEE 271: Applied Mechanics II, Dynamics Lecture 27: Ch.18, Sec.1 5 Prof. Albert S. Kim Civil and Environmental Engineering, University of Hawaii at Manoa Tuesday, November 27, 2012 2 / 42 KINETIC

More information

Inverted Pendulum System

Inverted Pendulum System Introduction Inverted Pendulum System This lab experiment consists of two experimental procedures, each with sub parts. Experiment 1 is used to determine the system parameters needed to implement a controller.

More information

Positioning Servo Design Example

Positioning Servo Design Example Positioning Servo Design Example 1 Goal. The goal in this design example is to design a control system that will be used in a pick-and-place robot to move the link of a robot between two positions. Usually

More information

TOPIC E: OSCILLATIONS SPRING 2019

TOPIC E: OSCILLATIONS SPRING 2019 TOPIC E: OSCILLATIONS SPRING 2019 1. Introduction 1.1 Overview 1.2 Degrees of freedom 1.3 Simple harmonic motion 2. Undamped free oscillation 2.1 Generalised mass-spring system: simple harmonic motion

More information

Phys 106 Practice Problems Common Quiz 1 Spring 2003

Phys 106 Practice Problems Common Quiz 1 Spring 2003 Phys 106 Practice Problems Common Quiz 1 Spring 2003 1. For a wheel spinning with constant angular acceleration on an axis through its center, the ratio of the speed of a point on the rim to the speed

More information

Appendix W. Dynamic Models. W.2 4 Complex Mechanical Systems. Translational and Rotational Systems W.2.1

Appendix W. Dynamic Models. W.2 4 Complex Mechanical Systems. Translational and Rotational Systems W.2.1 Appendix W Dynamic Models W.2 4 Complex Mechanical Systems W.2.1 Translational and Rotational Systems In some cases, mechanical systems contain both translational and rotational portions. The procedure

More information

Chapter 8 Rotational Motion

Chapter 8 Rotational Motion Chapter 8 Rotational Motion Chapter 8 Rotational Motion In this chapter you will: Learn how to describe and measure rotational motion. Learn how torque changes rotational velocity. Explore factors that

More information

LAST TIME: Simple Pendulum:

LAST TIME: Simple Pendulum: LAST TIME: Simple Pendulum: The displacement from equilibrium, x is the arclength s = L. s / L x / L Accelerating & Restoring Force in the tangential direction, taking cw as positive initial displacement

More information

2.4 Models of Oscillation

2.4 Models of Oscillation 2.4 Models of Oscillation In this section we give three examples of oscillating physical systems that can be modeled by the harmonic oscillator equation. Such models are ubiquitous in physics, but are

More information

6. Find the net torque on the wheel in Figure about the axle through O if a = 10.0 cm and b = 25.0 cm.

6. Find the net torque on the wheel in Figure about the axle through O if a = 10.0 cm and b = 25.0 cm. 1. During a certain period of time, the angular position of a swinging door is described by θ = 5.00 + 10.0t + 2.00t 2, where θ is in radians and t is in seconds. Determine the angular position, angular

More information

UNIVERSITI TUN HUSSEIN ONN MALAYSIA FINAL EXAMINATION SEMESTER I SESSION 2009/2010

UNIVERSITI TUN HUSSEIN ONN MALAYSIA FINAL EXAMINATION SEMESTER I SESSION 2009/2010 Aftisse^ UNIVERSITI TUN HUSSEIN ONN MALAYSIA SEMESTER I SESSION 2009/2010 SUBJECT : DYNAMICS SUBJECT CODE : BDA2013 COURSE : 2 BDD DATE : NOVEMBER 2009 DURATION : 2 */ 2 HOURS INSTRUCTION : ANSWER FOUR

More information

Final Examination Thursday May Please initial the statement below to show that you have read it

Final Examination Thursday May Please initial the statement below to show that you have read it EN40: Dynamics and Vibrations Final Examination Thursday May 0 010 Division of Engineering rown University NME: General Instructions No collaboration of any kind is permitted on this examination. You may

More information

In the presence of viscous damping, a more generalized form of the Lagrange s equation of motion can be written as

In the presence of viscous damping, a more generalized form of the Lagrange s equation of motion can be written as 2 MODELING Once the control target is identified, which includes the state variable to be controlled (ex. speed, position, temperature, flow rate, etc), and once the system drives are identified (ex. force,

More information

SRV02-Series Rotary Experiment # 7. Rotary Inverted Pendulum. Student Handout

SRV02-Series Rotary Experiment # 7. Rotary Inverted Pendulum. Student Handout SRV02-Series Rotary Experiment # 7 Rotary Inverted Pendulum Student Handout SRV02-Series Rotary Experiment # 7 Rotary Inverted Pendulum Student Handout 1. Objectives The objective in this experiment is

More information

CHAPTER 10 ROTATION OF A RIGID OBJECT ABOUT A FIXED AXIS WEN-BIN JIAN ( 簡紋濱 ) DEPARTMENT OF ELECTROPHYSICS NATIONAL CHIAO TUNG UNIVERSITY

CHAPTER 10 ROTATION OF A RIGID OBJECT ABOUT A FIXED AXIS WEN-BIN JIAN ( 簡紋濱 ) DEPARTMENT OF ELECTROPHYSICS NATIONAL CHIAO TUNG UNIVERSITY CHAPTER 10 ROTATION OF A RIGID OBJECT ABOUT A FIXED AXIS WEN-BIN JIAN ( 簡紋濱 ) DEPARTMENT OF ELECTROPHYSICS NATIONAL CHIAO TUNG UNIVERSITY OUTLINE 1. Angular Position, Velocity, and Acceleration 2. Rotational

More information

The basic principle to be used in mechanical systems to derive a mathematical model is Newton s law,

The basic principle to be used in mechanical systems to derive a mathematical model is Newton s law, Chapter. DYNAMIC MODELING Understanding the nature of the process to be controlled is a central issue for a control engineer. Thus the engineer must construct a model of the process with whatever information

More information

2.003 Engineering Dynamics Problem Set 4 (Solutions)

2.003 Engineering Dynamics Problem Set 4 (Solutions) .003 Engineering Dynamics Problem Set 4 (Solutions) Problem 1: 1. Determine the velocity of point A on the outer rim of the spool at the instant shown when the cable is pulled to the right with a velocity

More information

Textbook Reference: Wilson, Buffa, Lou: Chapter 8 Glencoe Physics: Chapter 8

Textbook Reference: Wilson, Buffa, Lou: Chapter 8 Glencoe Physics: Chapter 8 AP Physics Rotational Motion Introduction: Which moves with greater speed on a merry-go-round - a horse near the center or one near the outside? Your answer probably depends on whether you are considering

More information

AP Physics QUIZ Chapters 10

AP Physics QUIZ Chapters 10 Name: 1. Torque is the rotational analogue of (A) Kinetic Energy (B) Linear Momentum (C) Acceleration (D) Force (E) Mass A 5-kilogram sphere is connected to a 10-kilogram sphere by a rigid rod of negligible

More information

Quantitative Skills in AP Physics 1

Quantitative Skills in AP Physics 1 This chapter focuses on some of the quantitative skills that are important in your AP Physics 1 course. These are not all of the skills that you will learn, practice, and apply during the year, but these

More information

CHAPTER 8: ROTATIONAL OF RIGID BODY PHYSICS. 1. Define Torque

CHAPTER 8: ROTATIONAL OF RIGID BODY PHYSICS. 1. Define Torque 7 1. Define Torque 2. State the conditions for equilibrium of rigid body (Hint: 2 conditions) 3. Define angular displacement 4. Define average angular velocity 5. Define instantaneous angular velocity

More information

EE Homework 3 Due Date: 03 / 30 / Spring 2015

EE Homework 3 Due Date: 03 / 30 / Spring 2015 EE 476 - Homework 3 Due Date: 03 / 30 / 2015 Spring 2015 Exercise 1 (10 points). Consider the problem of two pulleys and a mass discussed in class. We solved a version of the problem where the mass was

More information

ASEISMIC DESIGN OF TALL STRUCTURES USING VARIABLE FREQUENCY PENDULUM OSCILLATOR

ASEISMIC DESIGN OF TALL STRUCTURES USING VARIABLE FREQUENCY PENDULUM OSCILLATOR ASEISMIC DESIGN OF TALL STRUCTURES USING VARIABLE FREQUENCY PENDULUM OSCILLATOR M PRANESH And Ravi SINHA SUMMARY Tuned Mass Dampers (TMD) provide an effective technique for viration control of flexile

More information

The Damped Pendulum. Physics 211 Lab 3 3/18/2016

The Damped Pendulum. Physics 211 Lab 3 3/18/2016 PHYS11 Lab 3 Physics 11 Lab 3 3/18/16 Objective The objective of this lab is to record the angular position of the pendulum vs. time with and without damping. The data is then analyzed and compared to

More information

Chapter 14 Oscillations. Copyright 2009 Pearson Education, Inc.

Chapter 14 Oscillations. Copyright 2009 Pearson Education, Inc. Chapter 14 Oscillations Oscillations of a Spring Simple Harmonic Motion Energy in the Simple Harmonic Oscillator Simple Harmonic Motion Related to Uniform Circular Motion The Simple Pendulum The Physical

More information

MECH 3140 Final Project

MECH 3140 Final Project MECH 3140 Final Project Final presentation will be held December 7-8. The presentation will be the only deliverable for the final project and should be approximately 20-25 minutes with an additional 10

More information

Handout 6: Rotational motion and moment of inertia. Angular velocity and angular acceleration

Handout 6: Rotational motion and moment of inertia. Angular velocity and angular acceleration 1 Handout 6: Rotational motion and moment of inertia Angular velocity and angular acceleration In Figure 1, a particle b is rotating about an axis along a circular path with radius r. The radius sweeps

More information

KNIFE EDGE FLAT ROLLER

KNIFE EDGE FLAT ROLLER EXPERIMENT N0. 1 To Determine jumping speed of cam Equipment: Cam Analysis Machine Aim: To determine jumping speed of Cam Formulae used: Upward inertial force = Wvω 2 /g Downward force = W + Ks For good

More information

Uniform Circular Motion

Uniform Circular Motion Uniform Circular Motion INTRODUCTION Uniform circular motion is the motion of an object traveling at a constant (uniform) speed in a circular path. Besides the speed, there are several other variables

More information

Your Name: PHYSICS 101 MIDTERM. Please circle your section 1 9 am Galbiati 2 10 am Kwon 3 11 am McDonald 4 12:30 pm McDonald 5 12:30 pm Kwon

Your Name: PHYSICS 101 MIDTERM. Please circle your section 1 9 am Galbiati 2 10 am Kwon 3 11 am McDonald 4 12:30 pm McDonald 5 12:30 pm Kwon 1 Your Name: PHYSICS 101 MIDTERM October 26, 2006 2 hours Please circle your section 1 9 am Galbiati 2 10 am Kwon 3 11 am McDonald 4 12:30 pm McDonald 5 12:30 pm Kwon Problem Score 1 /13 2 /20 3 /20 4

More information

State Space Representation

State Space Representation ME Homework #6 State Space Representation Last Updated September 6 6. From the homework problems on the following pages 5. 5. 5.6 5.7. 5.6 Chapter 5 Homework Problems 5.6. Simulation of Linear and Nonlinear

More information

Lectures Chapter 10 (Cutnell & Johnson, Physics 7 th edition)

Lectures Chapter 10 (Cutnell & Johnson, Physics 7 th edition) PH 201-4A spring 2007 Simple Harmonic Motion Lectures 24-25 Chapter 10 (Cutnell & Johnson, Physics 7 th edition) 1 The Ideal Spring Springs are objects that exhibit elastic behavior. It will return back

More information

In this chapter the energy and momentum methods will be added to the tools available for your study of the motion of rigid bodies.

In this chapter the energy and momentum methods will be added to the tools available for your study of the motion of rigid bodies. In this chapter the energy and momentum methods will be added to the tools available for your study of the motion of rigid bodies. For example, by using the principle of conservation of energy and direct

More information

Mechatronics Engineering. Li Wen

Mechatronics Engineering. Li Wen Mechatronics Engineering Li Wen Bio-inspired robot-dc motor drive Unstable system Mirko Kovac,EPFL Modeling and simulation of the control system Problems 1. Why we establish mathematical model of the control

More information

Chapter 8. Rotational Motion

Chapter 8. Rotational Motion Chapter 8 Rotational Motion The Action of Forces and Torques on Rigid Objects In pure translational motion, all points on an object travel on parallel paths. The most general motion is a combination of

More information

The University of Melbourne Engineering Mechanics

The University of Melbourne Engineering Mechanics The University of Melbourne 436-291 Engineering Mechanics Tutorial Eleven Instantaneous Centre and General Motion Part A (Introductory) 1. (Problem 5/93 from Meriam and Kraige - Dynamics) For the instant

More information

Overview of motors and motion control

Overview of motors and motion control Overview of motors and motion control. Elements of a motion-control system Power upply High-level controller ow-level controller Driver Motor. Types of motors discussed here; Brushed, PM DC Motors Cheap,

More information

Manufacturing Equipment Control

Manufacturing Equipment Control QUESTION 1 An electric drive spindle has the following parameters: J m = 2 1 3 kg m 2, R a = 8 Ω, K t =.5 N m/a, K v =.5 V/(rad/s), K a = 2, J s = 4 1 2 kg m 2, and K s =.3. Ignore electrical dynamics

More information

Project Lab Report. Michael Hall. Hao Zhu. Neil Nevgi. Station 6. Ta: Yan Cui

Project Lab Report. Michael Hall. Hao Zhu. Neil Nevgi. Station 6. Ta: Yan Cui Project Lab Report Michael Hall Hao Zhu Neil Nevgi Station 6 Ta: Yan Cui Nov. 12 th 2012 Table of Contents: Executive Summary 3 Modeling Report.4-7 System Identification 7-11 Control Design..11-15 Simulation

More information

1. [30] Y&F a) Assuming a small angle displacement θ max < 0.1 rad, the period is very nearly

1. [30] Y&F a) Assuming a small angle displacement θ max < 0.1 rad, the period is very nearly PH1140 D09 Homework 3 Solution 1. [30] Y&F 13.48. a) Assuming a small angle displacement θ max < 0.1 rad, the period is very nearly T = π L =.84 s. g b) For the displacement θ max = 30 = 0.54 rad we use

More information

DYNAMICS MOMENT OF INERTIA

DYNAMICS MOMENT OF INERTIA DYNAMICS MOMENT OF INERTIA S TO SELF ASSESSMENT EXERCISE No.1 1. A cylinder has a mass of 1 kg, outer radius of 0.05 m and radius of gyration 0.03 m. It is allowed to roll down an inclined plane until

More information

Physics 207 Lecture 25. Lecture 25. HW11, Due Tuesday, May 6 th For Thursday, read through all of Chapter 18. Angular Momentum Exercise

Physics 207 Lecture 25. Lecture 25. HW11, Due Tuesday, May 6 th For Thursday, read through all of Chapter 18. Angular Momentum Exercise Lecture 5 Today Review: Exam covers Chapters 14-17 17 plus angular momentum, rolling motion & torque Assignment HW11, Due Tuesday, May 6 th For Thursday, read through all of Chapter 18 Physics 07: Lecture

More information

PHYSICS LAB Experiment 9 Fall 2004 THE TORSION PENDULUM

PHYSICS LAB Experiment 9 Fall 2004 THE TORSION PENDULUM PHYSICS 83 - LAB Experiment 9 Fall 004 THE TORSION PENDULUM In this experiment we will study the torsion constants of three different rods, a brass rod, a thin steel rod and a thick steel rod. We will

More information