LUSTROUS DREAM V3. High Power Solid-State LED Light Source. Introduction

Transcription

1 High Power Solid-State LED Light Source Introduction For a brighter solid-state light source, Dream V3 is an energy-efficient building block generating enough light outputs suitable for most applications in lighting field. Dream V3 offers the best solid-state light source and you might realize your modern ideas of lightings. Dream V3 provides the best possible performance with lifetime longer than 30,000 hours*. Dream V3 is particularly designed for architects and commercial lighting designers. *Note1: To optimize product performance and life time, and Tb less than 50 should be applied. 1

2 Dream V3 Color Warm White Neutral White Cool White Part Number Matrix Table.1 P/N A305CLKACJ A305MWKACJ A305NWKACJ Dream V3 Chip Material Material GaN Base Dream V3 Chips Array 4 Chips Array 2

3 Mechanical Dimensions Dream V3 Note1: Drawing not to scale. All dimensions are in millimeters. 3

4 Recommended installation screw pitch Warning: Do not touch the lighting area during handling and assembling. 4

5 Flux Characteristics at DC 20mA,Junction Temperature Tj = 25 0 C Table.2 Color Minimum Luminous FluX(lm) Typical Luminous Flux (lm) Warm White (3000K) 200m 240 lm Neutral White (4000K) 280m 300lm Cool White (5000K) 320lm 330lm Note1: Luminous flux is measured in total power with tolerable errors of 10%. Minimum luminous flux performance guaranteed within published operating conditions. Note2: Higher luminous flux will become available in the near future. Electrical Characteristics Table.3 Forward Voltage(V)for DC 20mA forward current Color Min Typ Max Warm White Neutral White Cool White Note1: Lustrous Technology allows a tolerance of each LED for voltage measurements. 5

6 Optical Characteristics Color CCT(K) Table.4 Min Typ Max Warm White 2600K 3000K 3250K Viewing Angle CRI (degrees) 75 Neutral White 3250K 4000K 4750K ~ Cool White 4750K 5000K 10000K 75 Note1: CRI value is measured with tolerable errors of 10% Absolute Maximum Ratings Parameters Advised DC Forward Current (ma) Table.5 For DC 20mA forward current Warm White/ Neutral White/ Cool White 20mA LED Junction Temperature ( 0 C ) < 115 Thermal Resistance ( 0 C /W) ~1.3 Operating Temperature ( 0 C ) -20~ +85 Storage Temperature ( 0 C ) -20 ~ +50 Note1: Proper current operating must be observed to maintain junction temperature below the maximum. 6

7 Relative Intensity Warm White (3000K) Relative Spectral Power Wave Length (nm) Neutral White (4000K) 7

8 Relative Intensity Cool White (5000K) Wave Length (nm) 8

9 Typical Angular Beam Profile, Tj=25 0 C * View Angle: 120 degree * Note1:Detail beam profile data can be provided to certain qualified customers 9

10 Product Binning Typical manufacturing processes of LED result in a variation in performance surrounding the typical data sheet values. In order to minimize variation in the end product of application, Lustrous bins its products for performance in luminous flux and chromaticity. The tables below list the standard photometric bins for Lustrous LED. Product availability in a particular bin varies by product and production run. Please contact your Lustrous sales representative for further information regarding product availability. Binning Condition Color Table.6 Forward DC Current (ma) Warm White Neutral White 20mA Cool White Vf Binning Information Table.7 Dream V3 Vf Bin Code Min Max E F G H

11 Luminous Flux Binning Information * Table.8 BIN Code Lv (lm) Lv (lm) BIN Code min. max. min. max. A 5 20 L B M C N D O E P F Q G R H S I T J U K V *Note: Luminous flux is measured in total power with tolerable errors of 10%. 11

12 Chromaticity Binning Information ** Warm White **Note: Chromaticity is measured in Chromaticity Coordinate (CIE 1931-xy) with tolerable errors of +/

13 Table.9 Warm-White Bin Coordinates CCT (K) BIN Chromaticity Coordinate (CIE 1931-xy) Min Typ. Max CODE x1 y1 x2 y2 x3 y3 x4 y4 1Z Z 2Z Z Z A A A A 4A A A A A B B B B 4B B B B B

14 Neutral White Table.10 Natural White Bin Table CCT (K) BIN Chromaticity Coordinate (CIE 1931-xy) Min Typ. Max CODE x1 y1 x2 y2 x3 y3 x4 y4 1C C C 3C C C C

15 7C C D D D D 4D D D D D E E E E 4E E E E E

16 Cool White y NW Bin Table (4750K~10000K) K 8300K 1K 2K 7000K 1J 2J 3J 6350K 1I 2I 3I 1H 2H 3H 5700K 5000K 4750K 1F 1G 2F 2G 3F 3G x 16

17 Table.11 Cool White Bin Table CCT (K) BIN Chromaticity Coordinate (CIE 1931-xy) Min Typ. Max CODE x1 y1 x2 y2 x3 y3 x4 y4 1F F 2F F G G 2G G H H 2H H I I 2I I J J 2J J K 1K K

18 Print Code Guideline A3 05 CL K A C J XXXXXXXXXXXX 8 F J 2B XX XX XX Table.12 1 Type 2 Power 3 Color A3 05:5W NW:Cool White MW: Nature White CL:Warm White 4 Input Voltage J:120V K:220V 5 Current A:25mA C: 50mA 6 CRI B:80~90 C:70~80 D:60~ Customer Code Internal Code Vf Luminous Flux Chromaticity See Bin Code See Bin Code See Bin Code Definition Definition Definition Year Month Week 09: :January 01:01 st Week 10: :May 20:20 th Week 11: :October 45:45 th Week 18

19 Standard Packaging 19

20 Precaution for Use Over-drive proof 1. Customer must not drive the LEDs with reverse current and should apply resistors for extra protection. 2. The maximum overshot of driving current should be limited under normal driving current * 1.3 times. 3. The ripple of driving current should not over +/-10% of normal driving current. Storage 1. Do not open the moisture barrier bag (MBB) before the products are ready to be used. 2. Storage Condition (before opening the MBB): Storage Temperature: -20~+50 C Relative Humidity < 60% RH Please re-seal the MBB when storing longer than 3 weeks. The products should be used within half of a year. 3. Storage Condition (after opening the MBB): Storage Temperature: -20~+50 C Relative Humidity < 60% RH The products should be used (assembled)as soon as possible after opening the MBB. Otherwise, LED must be baked at 80+/-5, 24 hours before handling and assembling. Handling 1. Do not touch the lighting area during handling and assembling. 20

21 Company Information Lustrous Technology, founded in 2004, endeavors to bring a new era of solid-state lighting. Our R&D development center and production facilities are based in Taiwan, a famous island for IT technology in the world. Our products are well designed in both performance and reliability. Lustrous is one of the leading high-power LED manufacturer and solution provider in the world. **Lustrous Technology may make process and material changes affecting performance and characteristics of our products without further notice. These products supplied after changes will continue to meet published specifications, but may not be identical to products supplied as samples or under prior orders. Website: sales@lustrous.com.tw Tel: Fax: Address: 5F, No 212-1, Sec.3, Datong Rd, Shiji City, Taipei County 221, Taiwan All rights reserved. Product specifications are subject to change without further notice. 21

22 Appendix (1) Flux Characteristics at AC Input Voltage (220V) with lustrous PCB Driver Board. Color Input DC 20mA Factor : K Input AC 220V Warm White Neutral White Cool White Lm 0.75 Lm*0.75 Note1: Luminous flux is measured in total power with tolerable errors of 10%. Minimum luminous flux performance guaranteed within published operating conditions. Note2: Higher luminous flux will become available in the near future. Electrical Characteristics at AC Input Voltage (220V) with lustrous PCB Driver Board. Color Total Power consumption at AC Input Voltage (220V) Min Typ Max Warm White Neutral White Cool White Note1: Lustrous Technology allows a tolerance of each LED for voltage measurements. 22

23 Appendix (2) Dream V3 Driver Reference Input Voltage 220Vac±10V Input Frequency 60Hz Storage Temp ~+ 50 PF 0.9(120Vac Full Load)) Driver Efficency 80% Cable length by user Power consumption 1.0W 23