TECHNICAL INFORMATION
|
|
|
- Theodore Owens
- 5 years ago
- Views:
Transcription
1 TECHNICAL INFORMATION RATED PRIMARY OLTAGE () This is the supply assigned to the transformer by the manufacturer. RATED SECONDARY OLTAGE () This is the secondary output assigned to the transformer when supplied with the rated primary, frequency range, rated secondary, all assigned by the manufacturer for the specified operating conditions of the transformer. RATED POWER (A) The specified power levels in this catalogue are the secondary power levels, in other words, those available when the transformer is loaded. It is the product of the RMS rated secondary by the RMS rated. If the transformer has more than one output, the rated power denotes the maximum sum of the products of RMS rated secondary by the RMS rated secondary, respectively. This rated power is defined for rated ambient temperature conditions. example : P = 3,2 A ta 70/B The transformer can deliver 3.2A at maximum ambient (70), the load consisting of a resistor load defined by R(load) = U(sec) 2 /P (assigned U sec & P values), heating does not exceed the relevant limit for Class B components used in this construction. NOTE : When the transformer is intended to supply DC and in conjunction with rectifiers and smoothing capacitors, the A power required from the transformer is far higher than the U(DC) and I(DC) product. To help you to determine the true transformer power, our Technical Department is at your disposal. AMBIENT TEMPERATURE (ta) The maximum temperature at which the transformer may be operated continuously under nominal conditions of use. It is the air temperature measured close to the transformer after thermal stabilization when operating at rated conditions. HEATING The increase of the temperature when operating at rated conditions and maximum ambient temperature. The heating must be determined by the resistance method. TEMPERATURE CLASS The international classification of temperature classes is as follows : A 105 H 180 E B F It defines the maximum temperature the transformer components must withstand in continuous operation, in compliance with the N 85 IEC publication classification. There insulating materials are therefore certificated for the thermal index corresponding to the declared class in accordance with N 216 IEC standard. PARTICULAR POINTS OF STANDARD FOR SAFETY TRANSFORMERS On-load secondary tolerance. This should not differ from the rated value by more than : 10% for transformers with build-in resistance to short-circuits (a supplement of 5% is granted on the 2 nd secondary for tranformers with 2 secondaries). 5% for other transformers whatever the secondaries number. Off-load secondary. The values given in this catalogue are maximum theoretical values. NOTE : For safety transformers, this should never exceed 50 rms. In the case of a transformer with several secondaries, the sum of the secondary s should be less tan 50 rms. ADAPTED TRANSFORMERS FROM THE STANDARDS SERIES Any transformer whose requires Power and corresponding to those of our & range, and whose secondary can fit in our minimum to maximum secondary range will be covered by EN ,EN60950, or UL506 approvals, depending on the effective choice. SPECIAL TRANFORMERS MYRRA can use the 44000, or standard ranges to examine any transformer for compliance with your specifications and with international standards. On request, we can add thermal, thermal fuse, thermal switch-ctp. In certain cases, the addition of thermal enables the ambient temperature to be increased, while still complying with EN
2 0,6 A EI 30-5 SERIE acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Inherently short-circuits proof Insulation 4 K QUALITY IN SERIES PRIMARY OLTAGE 117 A ,94 T 70 B 0, ,95 T 70 B 0,6 Recommended layout for transformers with 1 secondary (Allows the use of a transformer with 2 secondary s) ,9 T 70 B 0, ,9 T 70 B 0, ,9 T 70 B 0, ,8 T 70 B 0, x 6 2 x 50 2 x 9,94 T 70 B 0, x 9 2 x 33 2 x 14,95 T 70 B 0, x 12 2 x 25 2 x 19,9 T 70 B 0, x 15 2 x 20 2 x 24,9 T 70 B 0, x 18 2 x 17 2 x 29,9 T 70 B 0, x 24 2 x 12 2 x 39,8 T 70 B 0,6 PRIMARY OLTAGE 230 A ,94 T 70 B 0, ,95 T 70 B 0, ,9 T 70 B 0, ,9 T 70 B 0, ,9 T 70 B 0, ,8 T 70 B 0, x 6 2 x 50 2 x 9,94 T 70 B 0, x 9 2 x 33 2 x 14,95 T 70 B 0, x 12 2 x 25 2 x 19,9 T 70 B 0, * 2 x 15 2 x 20 2 x 24,9 T 70 B 0, * 2 x 18 2 x 17 2 x 29,9 T 70 B 0, * 2 x 24 2 x 12 2 x 39,8 T 70 B 0,6 *To be noted : * marked transformers are non approved.. 5
3 1-1,8 A EI 30-10,5 SERIE PRIMARY OLTAGE 117 A ,6 T 70 B ,9 T 70 B ,2 T 70 B ,6 T 70 B ,9 T 70 B ,9 T 70 B X 6 2 x 83 2 x 8,6 T 70 B x 9 2 x 56 2 x 12,9 T 70 B x 12 2 x 42 2 x 19 T 70 B x 15 2 x 33 2 x 23,6 T 70 B x 18 2 x 28 2 x 24,9 T 70 B x 24 2 x 21 2 x 37,9 T 70 B 1 acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Inherently short-circuits proof 30 and 36 models are DE certified ,1 ta 70/B 1, ,3 ta 70/B 1, ,2 ta 70/B 1, ,3 ta 70/B 1, ,2 ta 70/B 1, ,3 ta 70/B 1, x x 10,1 ta 70/B 1, x x 15,3 ta 70/B 1, x x 20,2 ta 70/B 1, x x 25,0 ta 70/B 1, * 2 x x 31 ta 70/B 1, * 2 x x 43 ta 70/B 1, ,1 ta 70/B 1,8 2 s Recommended layout for transformers with 1 secondary ,2 ta 70/B 1, ,3 ta 70/B 1, ,3 ta 70/B 1, ,4 ta 70/B 1, ,6 ta 70/B 1, x 6 2 x x 10,1 ta 70/B 1, x 9 2 x x 15,2 ta 70/B 1, x 12 2 x 75 2 x 20,3 ta 70/B 1, x 15 2 x 60 2 x 27,3 ta 70/B 1,8 (Allows the use of a transformer with 2 secondary s) 6
4 1-1,8 A EI 30-10,5 SERIE Insulation 4 K *To be noted 2 x 15 and 2 x 24 models are non-approved. PRIMARY OLTAGE 230 A ,6 T 70 B ,9 T 70 B ,2 T 70 B ,6 T 70 B ,9 T 70 B ,9 T 70 B x 6 2 x 83 2 x 8,6 T 70 B x 9 2 x 56 2 x 12,9 T 70 B x 12 2 x 42 2 x 19 T 70 B x 15 2 x 33 2 x 23,6 T 70 B x 18 2 x 28 2 x 24,9 T 70 B * 2 x 24 2 x 21 2 x 37,9 T 70 B 1 Items usually available on stock ,1 ta 70/B 1, ,3 ta 70/B 1, ,2 ta 70/B 1, ,3 ta 70/B 1, ,2 ta 70/B 1, ,3 ta 70/B 1, x x 10,1 ta 70/B 1, x x 15,3 ta 70/B 1, x x 20,2 ta 70/B 1, x x 25,0 ta 70/B 1, * 2 x x 31 ta 70/B 1, * 2 x x 43 ta 70/B 1, ,1 ta 70/B 1, ,2 ta 70/B 1, ,3 ta 70/B 1, ,3 ta 70/B 1, ,4 ta 70/B 1, ,6 ta 70/B 1, x 6 2 x x 10,1 ta 70/B 1, x 9 2 x x 15,2 ta 70/B 1, x 12 2 x 75 2 x 20,3 ta 70/B 1, * 2 x 15 2 x 60 2 x 27,3 ta 70/B 1,8 7
5 1,5-1,8 A EI 30-12,5 SERIE PRIMARY OLTAGE 117 A ,7 T 70 B 1, ,5 T 70 B 1, ,3 T 70 B 1, ,2 T 70 B 1, ,8 T 70 B 1, ,6 T 70 B 1, X 6 2 x x 9,7 T 70 B 1, x 9 2 x 83 2 x 15 T 70 B 1, x 12 2 x 63 2 x 19,3 T 70 B 1, x 15 2 x 50 2 x 24,2 T 70 B 1, x 18 2 x 42 2 x 29 T 70 B 1, x 24 2 x 31 2 x 38,6 T 70 B 1,5 acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Inherently short-circuits proof 30 model is DE certified ,8 T 50 B 1, ,8 T 50 B 1, ,7 T 50 B 1, ,6 T 50 B 1, ,3 T 50 B 1, ,3 T 50 B 1, x 6 2 x x 9,8 T 50 B 1, x 9 2 x 94 2 x 15,2 T 50 B 1, x 12 2 x 71 2 x 19,7 T 50 B 1,7 2 s x 15 2 x 57 2 x 24,6 T 50 B 1, x 18 2 x 47 2 x 29,5 T 50 B 1, x 24 2 x 35 2 x 39,3 T 50 B 1, ,8 T 40 B 1, ,8 T 40 B 1, ,7 T 40 B 1, ,6 T 40 B 1, ,3 T 40 B 1, ,3 T 40 B 1, x 6 2 x x 9,8 T 40 B 1, x 9 2 x x 15,2 T 40 B 1, x 12 2 x 75 2 x 19,7 T 40 B 1, x 15 2 x 60 2 x 24,6 T 40 B 1, x 18 2 x 50 2 x 29,5 T 40 B 1, x 24 2 x 38 2 x 39,3 T 40 B 1,8 Recommended layout for transformers with 1 secondary (Allows the use of a transformer with 2 secondary s) QUALITY IN SERIES 8
6 1,5-1,8 A EI 30-12,5 SERIE Insulation 4 K *To be noted : 2 x 18 and 2 x 24 models are non-approved. PRIMARY OLTAGE 230 A ,7 T 70 B 1, ,5 T 70 B 1, ,3 T 70 B 1, ,2 T 70 B 1, ,8 T 70 B 1, ,6 T 70 B 1, X 6 2 x x 9,7 T 70 B 1, x 9 2 x 83 2 x 15 T 70 B 1, x 12 2 x 63 2 x 19,3 T 70 B 1, x 15 2 x 50 2 x 24,2 T 70 B 1, * 2 x 18 2 x 42 2 x 29 T 70 B 1, * 2 x 24 2 x 31 2 x 38,6 T 70 B 1,5 Items usually available on stock ,8 T 50 B 1, ,8 T 50 B 1, ,7 T 50 B 1, ,6 T 50 B 1, ,3 T 50 B 1, ,3 T 50 B 1, x 6 2 x x 9,8 T 50 B 1, x 9 2 x 94 2 x 15,2 T 50 B 1, x 12 2 x 71 2 x 19,7 T 50 B 1, x 15 2 x 57 2 x 24,6 T 50 B 1, * 2 x 18 2 x 47 2 x 29,5 T 50 B 1, * 2 x 24 2 x 35 2 x 39,3 T 50 B 1, ,8 T 40 B 1, ,8 T 40 B 1, ,7 T 40 B 1, ,6 T 40 B 1, ,3 T 40 B 1, ,3 T 40 B 1, x 6 2 x x 9,8 T 40 B 1, x 9 2 x x 15,2 T 40 B 1, x 12 2 x 75 2 x 19,7 T 40 B 1, x 15 2 x 60 2 x 24,6 T 40 B 1, * 2 x 18 2 x 50 2 x 29,5 T 40 B 1, * 2 x 24 2 x 38 2 x 39,3 T 40 B 1,8 9
7 2-2,4 A EI 30-15,5 SERIE PRIMARY OLTAGE 117 A ,4 T 70 B ,5 T 70 B ,7 T 70 B ,8 T 70 B ,8 T 70 B ,4 T 70 B X 6 2 x x 10,4 T 70 B x 9 2 x x 15,4 T 70 B x 12 2 x 83 2 x 20,7 T 70 B x 15 2 x 67 2 x 25,8 T 70 B x 18 2 x 56 2 x 30,8 T 70 B x 24 2 x 42 2 x 41,4 T 70 B 2 acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Inherently short-circuits proof 30 model is DE certified Insulation 4 K ,5 T 50 B 2, ,5 T 50 B 2, T 50 B 2, ,3 T 50 B 2, T 50 B 2, T 50 B 2, x 6 2 x x 10,5 T 50 B 2, x 9 2 x x 15,5 T 50 B 2, x 12 2 x 96 2 x 21 T 50 B 2, x 15 2 x 77 2 x 24,5 T 50 B 2, x 18 2 x 64 2 x 31 T 50 B 2, x 24 2 x 48 2 x 42 T 50 B 2,3 2 s ,5 T 40 B 2, ,5 T 40 B 2, T 40 B 2, ,3 T 40 B 2, T 40 B 2, T 40 B 2, x 6 2 x x 10,5 T 40 B 2, x 9 2 x x 15,5 T 40 B 2, x 12 2 x x 21 T 40 B 2, x 15 2 x 80 2 x 24,5 T 40 B 2, x 18 2 x 67 2 x 31 T 40 B 2, x 24 2 x 50 2 x 42 T 40 B 2,4 Recommended layout for transformers with 1 secondary (Allows the use of a transformer with 2 secondary s) 10
8 2-2,4 A EI 30-15,5 SERIE *To be noted : 2 x 18 and 2 x 24 models are non-approved. PRIMARY OLTAGE 230 A ,4 T 70 B ,5 T 70 B ,7 T 70 B ,8 T 70 B ,8 T 70 B ,4 T 70 B X 6 2 x x 10,4 T 70 B x 9 2 x x 15,4 T 70 B x 12 2 x 83 2 x 20,7 T 70 B x 15 2 x 67 2 x 25,8 T 70 B * 2 x 18 2 x 56 2 x 30,8 T 70 B * 2 x 24 2 x 42 2 x 41,4 T 70 B 2 Items usually available on stock ,5 T 50 B 2, ,5 T 50 B 2, T 50 B 2, ,3 T 50 B 2, T 50 B 2, T 50 B 2, x 6 2 x x 10,5 T 50 B 2, x 9 2 x x 15,5 T 50 B 2, x 12 2 x 96 2 x 21 T 50 B 2, x 15 2 x 77 2 x 24,5 T 50 B 2, * 2 x 18 2 x 64 2 x 31 T 50 B 2, * 2 x 24 2 x 48 2 x 42 T 50 B 2, ,5 T 40 B 2, ,5 T 40 B 2, T 40 B 2, ,3 T 40 B 2, T 40 B 2, T 40 B 2, x 6 2 x x 10,5 T 40 B 2, x 9 2 x x 15,5 T 40 B 2, x 12 2 x x 21 T 40 B 2, x 15 2 x 80 2 x 24,5 T 40 B 2, * 2 x 18 2 x 67 2 x 31 T 40 B 2, * 2 x 24 2 x 50 2 x 42 T 40 B 2,4 11
9 2,3-2,8 A EI SERIE PRIMARY OLTAGE 117 A ,5 T 70 B 2, ,7 T 70 B 2, T 70 B 2, ,9 T 70 B 2, ,4 T 70 B 2, ,9 T 70 B 2, X 6 2 x x 10,5 T 70 B 2, x 9 2 x x 15,7 T 70 B 2, x 12 2 x 96 2 x 21 T 70 B 2, x 15 2 x 77 2 x 25,9 T 70 B 2, x 18 2 x 64 2 x 31,4 T 70 B 2, x 24 2 x 48 2 x 41,9 T 70 B 2,3 acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Inherently short-circuits proof 30 model is DE certified ,5 T 50 B 2, ,4 T 50 B 2, ,1 T 50 B 2, ,3 T 50 B 2, ,9 T 50 B 2, T 50 B 2, x 6 2 x x 10,5 T 50 B 2, x 9 2 x x 15,4 T 50 B 2, x 12 2 x x 21,1 T 50 B 2, x 15 2 x 90 2 x 26,3 T 50 B 2, x 18 2 x 75 2 x 31,5 T 50 B 2, x 24 2 x 56 2 x 42,1 T 50 B 2, ,5 T 40 B 2,8 2 s Recommended layout for transformers with 1 secondary ,4 T 40 B 2, ,1 T 40 B 2, ,3 T 40 B 2, ,9 T 40 B 2, ,1 T 40 B 2, x 6 2 x x 10,5 T 40 B 2, x 9 2 x x 15,4 T 40 B 2, x 12 2 x x 21,1 T 40 B 2, x 15 2 x 93 2 x 26,3 T 40 B 2, x 18 2 x 77 2 x 31,5 T 40 B 2, x 24 2 x 58 2 x 42,1 T 40 B 2,8 (Allows the use of a transformer with 2 secondary s) 12
10 2,3-2,8 A EI SERIE Insulation 4 K *To be noted : 2 x 18 and 2 x 24 models are non-approved. PRIMARY OLTAGE 230 A ,5 T 70 B 2, ,7 T 70 B 2, T 70 B 2, ,9 T 70 B 2, ,4 T 70 B 2, ,9 T 70 B 2, X 6 2 x x 10,5 T 70 B 2, x 9 2 x x 15,7 T 70 B 2, x 12 2 x 96 2 x 21 T 70 B 2, x 15 2 x 77 2 x 25,9 T 70 B 2, * 2 x 18 2 x 64 2 x 31,4 T 70 B 2, * 2 x 24 2 x 48 2 x 41,9 T 70 B 2,3 Items usually available on stock ,5 T 50 B 2, ,4 T 50 B 2, ,1 T 50 B 2, ,3 T 50 B 2, ,9 T 50 B 2, T 50 B 2, x 6 2 x x 10,5 T 50 B 2, x 9 2 x x 15,4 T 50 B 2, x 12 2 x x 21,1 T 50 B 2, x 15 2 x 90 2 x 26,3 T 50 B 2, * 2 x 18 2 x 75 2 x 31,5 T 50 B 2, * 2 x 24 2 x 56 2 x 42,1 T 50 B 2, ,5 T 40 B 2, ,4 T 40 B 2, ,1 T 40 B 2, ,3 T 40 B 2, ,9 T 40 B 2, ,1 T 40 B 2, x 6 2 x x 10,5 T 40 B 2, x 9 2 x x 15,4 T 40 B 2, x 12 2 x x 21,1 T 40 B 2, x 15 2 x 93 2 x 26,3 T 40 B 2, * 2 x 18 2 x 70 2 x 31,5 T 40 B 2, * 2 x 24 2 x 58 2 x 42,1 T 40 B 2,8 13
11 3,2 A EI 38-13,6 SERIE PRIMARY OLTAGE 117 A T 70 B 3, T 70 B 3,2 acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Fuse on secondary side (see diagram) to be assumed by customer T 70 B 3, T 70 B 3, ,1 T 70 B 3, ,1 T 70 B 3, x 6 2 x x 8 T 70 B 3, x 9 2 x x 12 T 70 B 3,2 2 s x 12 2 x x 16 T 70 B 3, x 15 2 x x 20 T 70 B 3, x 18 2 x 89 2 x 24 T 70 B 3, x 24 2 x 67 2 x 32,1 T 70 B 3,2 Recommended layout for transformers with 1 secondary (Allows the use of a transformer with 2 secondary s) 5 A EI 42-14,8 SERIE PRIMARY OLTAGE ,4 T 50 B ,6 T 50 B ,9 T 50 B T 50 B ,3 T 50 B ,7 T 50 B x 6 2 x x 8,4 T 50 B x 9 2 x x 12,6 T 50 B x 12 2 x x 16,9 T 50 B x 15 2 x x 21 T 50 B x 18 2 x x 25,3 T 50 B x 24 2 x x 33,7 T 50 B 5 A acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Fuse on secondary side (see diagram) to be assumed by customer 2 s Recommended layout for transformers with 1 secondary (Allows the use of a transformer with 2 secondary s)
12 3,2 A EI 38-13,6 SERIE and 36 models are DE certified Insulation 4 K PRIMARY OLTAGE 230 A *To be noted : 2 x 24 model is non-approved T 70 B 3, T 70 B 3, T 70 B 3, T 70 B 3, ,1 T 70 B 3, ,1 T 70 B 3, x 6 2 x x 8 T 70 B 3, x 9 2 x x 12 T 70 B 3, x 12 2 x x 16 T 70 B 3, x 15 2 x x 20 T 70 B 3, x 18 2 x 89 2 x 24 T 70 B 3, * 2 x 24 2 x 67 2 x 32,1 T 70 B 3,2 5 A EI 42-14,8 SERIE and 36 models are DE certified Insulation 4 K PRIMARY OLTAGE 230 A *To be noted : 2 x 24 model is non-approved ,4 T 50 B ,6 T 50 B ,9 T 50 B T 50 B ,3 T 50 B ,7 T 50 B x 6 2 x x 8,4 T 50 B x 9 2 x x 12,6 T 50 B x 12 2 x x 16,9 T 50 B x 15 2 x x 21 T 50 B x 18 2 x x 25,3 T 50 B * 2 x 24 2 x x 33,7 T 50 B 5 15
13 10 A EI 48-16,8 SERIE PRIMARY OLTAGE 117 A ,2 T 50 B 10 acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Fuse on primary side (see diagram) to be assumed by customer ,8 T 50 B ,4 T 50 B ,1 T 50 B ,6 T 50 B ,9 T 50 B x 6 2 x x 7,2 T 50 B x 9 2 x x 10,8 T 50 B s x 12 2 x x 14,4 T 50 B x 15 2 x x 18,1 T 50 B x 18 2 x x 21,6 T 50 B x 24 2 x x 28,9 T 50 B Recommended layout for transformers with 1 secondary (Allows the use of a transformer with 2 secondary s) 16 A EI 54-18,8 SERIE PRIMARY OLTAGE 117 A 2, ,4 T 50 B 16 2, ,1 T 50 B 16 1, ,7 T 50 B ,4 T 50 B ,1 T 50 B 16 0, ,3 T 50 B 16 1, x 6 2 x x 7,4 T 50 B x 9 2 x x 11,1 T 50 B 16 0, x 12 2 x x 14,7 T 50 B 16 0, x 15 2 x x 18,4 T 50 B 16 0, x 18 2 x x 22 T 50 B 16 0, x 24 2 x x 29,3 T 50 B 16 acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Fuse on secondary side (see diagram) to be assumed by customer 2 1 s Recommended layout for transformers with 1 secondary (Allows the use of a transformer with 2 secondary s)
14 10 A EI 48-16,8 SERIE and 36 models are DE certified Insulation 4 K *To be noted : 2 x 24 model is non-approved. PRIMARY OLTAGE 230 A ,2 T 50 B ,8 T 50 B ,4 T 50 B ,1 T 50 B ,6 T 50 B ,9 T 50 B x 6 2 x x 7,2 T 50 B x 9 2 x x 10,8 T 50 B x 12 2 x x 14,4 T 50 B x 15 2 x x 18,1 T 50 B x 18 2 x x 21,6 T 50 B * 2 x 24 2 x x 28,9 T 50 B A EI 54-18,8 SERIE and 36 models are DE certified Insulation 4 K *To be noted : 2 x 24 model is non-approved. PRIMARY OLTAGE 230 A 2, ,4 T 50 B 16 2, ,1 T 50 B 16 1, ,7 T 50 B ,4 T 50 B ,1 T 50 B 16 0, ,3 T 50 B 16 1, x 6 2 x x 7,4 T 50 B x 9 2 x x 11,1 T 50 B 16 0, x 12 2 x x 14,7 T 50 B 16 0, x 15 2 x x 18,4 T 50 B 16 0, x 18 2 x x 22 T 50 B 16 0, * 2 x 24 2 x x 29,3 T 50 B 16 17
15 22 A EI SERIE PRIMARY OLTAGE 117 A ,8 T 50 B 22 acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Fuse on primary side (see diagram) to be assumed by customer ,3 T 50 B ,7 T 50 B ,1 T 50 B ,5 T 50 B ,3 T 50 B x 6 2 x x 6,8 T 50 B x 9 2 x x 10,3 T 50 B s x 12 2 x x 13,7 T 50 B x 15 2 x x 17,1 T 50 B x 18 2 x x 20,5 T 50 B x 24 2 x x 27,3 T 50 B Recommended layout for transformers with 1 secondary (Allows the use of a transformer with 2 secondary s) 30 A EI SERIE PRIMARY OLTAGE 117 A ,9 T 50 B ,3 T 50 B ,8 T 50 B ,2 T 50 B ,8 T 50 B ,7 T 50 B x 6 2 x x 6,9 T 50 B x 9 2 x x 10,3 T 50 B x 12 2 x x 13,8 T 50 B x 15 2 x x 17,2 T 50 B x 18 2 x x 20,8 T 50 B x 24 2 x x 27,7 T 50 B 30 acuum filling Self-extinguishing plastics UL 94 O Degree of IP grams weight Fuse on primary side (see diagram) to be assumed by customer 2 1 s Recommended layout for transformers with 1 secondary (Allows the use of a transformer with 2 secondary s)
16 22 A EI SERIE and 36 models are DE certified Insulation 4 K *To be noted : 2 x 24 model is non-approved. PRIMARY OLTAGE 230 A ,8 T 50 B ,3 T 50 B ,7 T 50 B ,1 T 50 B ,5 T 50 B ,3 T 50 B x 6 2 x x 6,8 T 50 B x 9 2 x x 10,3 T 50 B x 12 2 x x 13,7 T 50 B x 15 2 x x 17,1 T 50 B x 18 2 x x 20,5 T 50 B * 2 x 24 2 x x 27,3 T 50 B A EI SERIE and 36 models are DE certified Insulation 4 K *To be noted : 2 x 24 model is non-approved. PRIMARY OLTAGE 230 A ,9 T 50 B ,3 T 50 B ,8 T 50 B ,2 T 50 B ,8 T 50 B ,7 T 50 B x 6 2 x x 6,9 T 50 B x 9 2 x x 10,3 T 50 B x 12 2 x x 13,8 T 50 B x 15 2 x x 17,2 T 50 B x 18 2 x x 20,8 T 50 B * 2 x 24 2 x x 27,7 T 50 B 30 19
17 BOXES WITH FIXING SUPPORT SERIE L H L H X P O O X P Y EI 38 EI 42 EI 48 4X X X X X2.5 EI 54 EI 60 EI X X X X X X5.0 CIRCUIT For boxes with 2 lugs and pin type output, add suffix 1 to the reference of the standard transformer (example : ) For boxes with 2 lugs and 2,8 «faston» output, add suffix 2 to the reference of the standard transformer (example : ) For boxes with 4 lugs and pin type output, add suffix 3 to the reference of the standard transformer (example : ) For boxes with 4 lugs and 2,8 «faston» output, add suffix 4 to the reference of the standard transformer (example : ) These models are not available on stock. L P H X Y Ø ± 0,50 ± 0,40 ± 0,40 ± 0,50 ± 0,50 ±0,3 EI 38 X 13,6 55,6 34,9 28,1 47,5 3,2 EI 42 X 14, ,3 55,0 4,2 EI 48 X 16, ,3 34,6 60 4,2 EI 54 X 18, ,3 38,8 65 4,2 EI 60 X 21 81,5 53,3 44,7 72,5 43,5 4,2 EI 66 X 23 87,2 58,6 48,5 77,5 47,5 4,2 Series transformers can be equiped with boxes with lugs and also 2,8 «faston» terminal tags while still conforming to the specifications in the standard references. 20
S R O T C U D IN & MYRRA
TRANSFORMERS & INDUCTORS MYRRA...Of course! TECHNICAL INFORMATION RATED PRIMARY OLTAGE () This is the supply assigned to the transformer by the manufacturer. RATED SECONDARY OLTAGE () This is the secondary
Film Capacitors. EMI suppression capacitors. Date: June 2018
Film Capacitors EMI suppression capacitors Date: June 2018 EPCOS AG 2018. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without
Ref: HLSR 16-PW; HLSR 32-PW; HLSR 40-PW-000; HLSR 50-PW-000,
Digital Current Transducer HLSR-PW series I P N = 16... 50 A Ref: HLSR 16-PW; HLSR 32-PW; HLSR 40-PW-000; HLSR 50-PW-000, Bitstream output from on onboard Sigma Delta modulator. For the electronic measurement
TURQUOISE SWITCHES V TYPE (ABV)
HIGH ENVIRONMENTAL RESISTANCE TURQUOISE SWITCHES V TYPE (ABV) FEATURES Miniature size (33 15.9.3 mm) (99.626.406 inch) Sealed construction for use in adverse environment Sealed construction by epoxy resin
Non-Contact Safety Systems CMS
Selection table for non-contact safety system // Evaluation units Connection Desi Read head contact assembly Assured switch-on distance S ao [mm] Assured switch-on distance S ar [mm] Number of outputs
Aluminum Capacitors Power Standard Miniature Snap-In
Aluminum Capacitors Power Standard Miniature Snap-In Fig. QUICK REFERENCE DATA DESCRIPTION / PUM-SI smaller dimensions 0/0 PSM-SI long life 0 C Note () A 0 V range is available on request 0/0 PLL-SI VALUE
DC/DC converter Input 9-36 and Vdc Output up to 0.5A/3W
PKV 3000 I PKV 5000 I DC/DC converter Input 9-36 and 18-72 Vdc up to 0.5A/3W Key Features Industry standard DIL24 Wide input voltage range, 9 36V, 18 72V High efficiency 74 83% typical Low idling power
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer HO-NP/SP33 series I PN = 8, 15, 25 A Ref: HO 8-NP/SP33, HO 15-NP/SP33, HO 25-NP/SP33 For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the
Aluminum Electrolytic Capacitors Power Long Life Snap-In
Aluminum Electrolytic Capacitors Power Long Life Snap-In PUL-SI smaller dimensions 0/0 PLL-SI Fig. QUICK REFERENCE DATA DESCRIPTION VALUE 0 0 Nominal case sizes (Ø D x L in mm) x to x 0 Rated capacitance
Type EI30 / 23.0 F F F F
THAI LIN RADIO since 1 #1 #2 #3 #4 # # #8 # Bottom View A F F F F Type EI30 / 23.0 Power 2.7/2.8/2./3.0/3.2VA Frequency 50/0 Hz Temperature class Class B (130 C) Ambient temperature (ta) C C Dielectric
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer HO-NP series I P N = 4, 6, 12, 15 A Ref: HO 4-NP, HO 6-NP, HO 12-NP, HO 15-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary
Digital Current Transducer HO-SW series I P N = A. Ref: HO 100-SW; HO 150-SW; HO 200-SW; HO 250-SW
Digital Current Transducer HO-SW series I P N = 100... 250 A Ref: HO 100-SW; HO 150-SW; HO 200-SW; HO 250-SW Bitstream output from on onboard Sigma Delta modulator. For the electronic measurement of current:
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer HO-NSM series I PN = 8, 15, 25 A Ref: HO 8-NSM, HO 15-NSM, HO 25-NSM For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the
Analogue Meters CQ2x07 series
Analogue Meters CQ2x07 series Analogue Power Meters Active, reactive, apparent power meters and Power factor meters with exchangeable scales EQ0207/2207/0107/2107 & YQ0207/2207/0107/2107 o Measurement
DC/DC regulator Input V Output up to 16 A
PMC 4000 series Contents Product Program...................... 2 Mechanical Data...................... 3 Connections......................... 3 Absolute Maximum Ratings............. 4 Input...............................
APPROVAL SHEET FOR AL. ELECTROLYTIC CAPACITORS
NO : ED-A5540 TO : APPROVED APPROVAL SHEET FOR AL. ELECTROLYTIC CAPACITORS : BY: Series Description Part No. HV series, PLEASE RETURN US ONE COPY YOUR SIGED SPECIFICATION AFTER YOU APPROVED OF IT. APPROVED
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer LDSR 0.3-TP/SP1 I P R N = 300 ma For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed
Chip Type Y5U Temperature Characteristics
Chip Type Y5U Temperature Characteristics Features Dimensions Large capacitance in small size Temperature characteristics of Y5U (within +% to 56% in the range of 5 C to +85 C) Features equivalent to X7V.
THE DIMENSIONING OF ELECTRICAL CONDUCTORS FOR USE IN "PANEL BOARDS" ADDRESSED TO HAZARDOUS AREAS - PART THREE
July 04 THE DIMENSIONING OF ELECTRICAL CONDUCTORS FOR USE IN "PANEL BOARDS" ADDRESSED TO HAZARDOUS AREAS - PART THREE In this third part. we want to speak about how important is the correct sizing of the
Recommended Land Pattern: [mm]
![Recommended Land Pattern: [mm]](/thumbs/84/89483599.jpg "Recommended Land Pattern: [mm]")
Dimensions: [mm] Recommended Land Pattern: [mm] Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 1 V/ 1 khz ± 0.2 khz C 150 nf ±10% Rated Voltage U R 310 V (AC) max. Rated
HIGH VOLTAGE MULTILAYER CERAMIC CAPACITORS
DESCRIPTION: RoHS compliant (*) Capacitors 0805 to 6560 Rated voltage 1000V to 10KV Dielectric Type I and II SMD and leaded versions * Non RoHS version still maintained for current applications. I. Foreword
THREE PHASE CAPACITOR For WIND TURBINES
RS/Cond 28.04.2003 Pg: 1 / 3 THREE PHASE CAPACITOR For WIND TURBINES Applications: Three-phase capacitor for Wind Turbine has been designed for power factor correction in high harmonic current content.
SPECIFICATION SS 51/9 400KV COUPLING CAPACITORS FOR POWER LINE CARRIER SYSTEM
INDEPENDENT POWER TRANSMISSION OPERATOR S.A. TNPRD/ SUBSTATION SPECIFICATION & EQUIPMENT SECTION January 2017 SPECIFICATION SS 51/9 400KV COUPLING CAPACITORS FOR POWER LINE CARRIER SYSTEM I. SCOPE This
Aluminum Electrolytic Capacitors Power Standard Miniature Snap-In
Aluminum Electrolytic Capacitors Power Standard Miniature Snap-In Fig. QUICK REFERENCE DATA DESCRIPTION / PUM-SI smaller dimensions 0/0 PSM-SI long life 0 C Note () A 0 V range is available on request
DC/DC converter Input 9-36 and Vdc Output up to 0.5A/3W
PKV 3000 I PKV 5000 I DC/DC converter Input 9-36 and 18-72 Vdc up to 0.5A/3W Key Features Industry standard DIL24 Wide input voltage range, 9 36V, 18 72V High efficiency 74 83% typical Low idling power
Surface Mount Multilayer Ceramic Chip Capacitors for Safety Certified Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Safety Certified Applications FEATURES Approved IEC 60384-14 Specialty: safety certified capacitors Wet build process Reliable Noble Metal Electrode
POWER ELECTRONICS CAPACITORS MKV SERIES. Self healing Bi-metallized paper capacitors for heavy duty AC applications CERT. N.
POWER ELECTRONICS CAPACITORS MKV SERIES Self healing Bi-metallized paper capacitors for heavy duty AC applications CERT. N.9170 ICAR UNI EN 29001 (ISO 9001) 1. COMPANY PROFILE OUR MISSION: Develop and
WCAP-FTXX Film Capacitors
A Dimensions: [mm] B Recommended hole pattern: [mm] D1 Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 1 V/ 1 khz ± 0.2 khz C 0.1000 µf ± 10% Rated voltage U R 310 V (AC)
Universal limit switches
SWITCHES.CROUZET.COM 1 LIMIT SWITCHES 0/016 Universal limit switches 8384 standard 8384 with positive break operation Conformity to standards IEC / EN 60947--1, including Annex K for version with positive
Aluminum Electrolytic Capacitors Power Long Life Snap-In
Aluminum Electrolytic Capacitors Power Long Life Snap-In PUL-SI smaller dimensions 0/0 PLL-SI Fig. QUICK REFERENCE DATA DESCRIPTION VALUE 0 0 Nominal case sizes (Ø D x L in mm) x to x 0 Rated capacitance
Capacitors. Typical electrical characteristics of metallized polyester capacitors KEU. Type KEU Metallized polyester capacitors
Capacitors Type KEU Metallized polyester capacitors As a dielectric high quality polyester film with good electrical properties is used. Electrodes of capacitor are vacuum metallized aluminium. The thickness
MKP-X2 TECHNICAL TERMS EXPLANATION
TECHNICAL TERMS EXPLANATION Rated capacitance Capacitance referred to 1 khz, 20 +-1ºC, 65+-2% of relative humidity and 96+- 10 kpa. In case of doubt please refer to IEC 60068-1, sub-clause 5.2. Capacitance
Aluminum Capacitors Power Printed Wiring Style
FEATURES Polarized aluminum electrolytic capacitors, non-solid electrolyte Large types, cylindrical aluminum case, insulated Provided with keyed polarity Very long useful life: 000 h at 8 C Low ESR, high
Recommended Hole Pattern: [mm]
![Recommended Hole Pattern: [mm]](/thumbs/77/74984900.jpg "Recommended Hole Pattern: [mm]")
Dimensions: [mm] Recommended Hole Pattern: [mm] Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 1 V/ 1 khz ± 0.2 khz C 680 nf ±10% Rated Voltage U R 400 V (DC) Insulation
Metallized PPS Capacitors for extreme capacitance stability. 1 min / 23 C B
Replaces CKM 501 B series Applications & Characteristics Railway signalling High-temperature (125 C) High capacitance stability Harmonized circuits Filtering High-reliability circuits Security applications
Funkentstör-Kondensatoren der Klasse X2
STÖRSCHUTZ-KONDENSATOREN Funkentstör-Kondensatoren der Klasse X2 TECHNICAL TERMS EXPLANATION Rated capacitance Capacitance referred to 1 khz, 20 +-1ºC, 65+-2% of relative humidity and 96+- 10 kpa. In case
5SJ4...-.HG Circuit Breakers to IEC and UL 489
Siemens AG 009 5SJ...-.HG Circuit Breakers to IEC and UL 89 BETA Low-Voltage Circuit Protection Compliance with industry standards is a must in today's manufacturing environment. Worldwide acceptance is
FEATURES APPLICATIONS DESCRIPTION QUICK REFERENCE DATA. PILKOR components
FEATURES Excellent anti-surge characteristics Stable characteristics to moisture resistance even in high resistance range. Good replacement for ceramic plate resistors. APPLICATIONS Telecommunication Industrial
K04 TYPE -40 C +85 C 20000H
K04 TYPE -40 C +85 C 20000H Extended life. Surge-proof capacitor in aluminium can with insulation sleeve. To be mounted with ring clips or with threaded stud. Designed for high resistances to voltage spikes.
worldwide capacitors
worldwide capacitors CORPORATE PROFILE 1960 - CGE is established in Mexico City as an Electrical Component Manufacturer 190 CGE merges with CentraLab (NA Philips) and expand into electromechanical components
Conductive Polymer Aluminum Capacitors SMD (Chip), Low Impedance
Conductive Polymer Aluminum Capacitors SMD (Chip), Low Impedance FEATURES Long useful life: up to 5000 h at 105 C Very low ESR and highest ripple current SMD-version with base plate, lead (Pb) free reflow
4 400 VDC VDC H ±3 % J ±5 % 40 C to +105 C 400 VDC, 630 VDC
Plastic Film Capacitors Metallized Polypropylene Film Capacitor Type: ECWF(L) Designed for high frequency and current applications. Features Small size Excellent frequency characteristics Low loss 8 C,
Interference suppression film capacitors MKP 336 1
MKP RADIAL POTTED TYPE PITCH /15/22.5/27.5 mm l b h lt P d t CBA196 Fig.1 Simplified outlines. FEATURES to 27.5 mm lead pitch Supplied loose in box and taped on reel Consists of a low-inductive wound cell
Aluminum Capacitors Power Long Life Snap-In
0/0 PLL-SI PUL-SI smaller dimensions 0/0 PLL-SI QUICK REFERENCE DATA DESCRIPTION VALUE 0 0 Nominal case sizes (Ø D x L in mm) x to x 0 Rated capacitance range (E series), to 000 µf Tolerance on ± 0 % Rated
AN78xx/AN78xxF Series
3-pin positive output voltage regulator ( type) Overview The N7xx series and the N7xxF series are 3- pin, fixed positive output type monolithic voltage regulators. Stabilized fixed output voltage is obtained
Aluminum Capacitors Axial Miniature, Long-Life
8 AML 0 ASM Fig. Component outlines smaller dimensions 8 AML Aluminum Capacitors longer life 8 AHT 0 ATC FEATURES Polarized aluminum electrolytic capacitors, non-solid electrolyte Axial leads, cylindrical
TPC Suppressor Capacitors Classes X & Y A KYOCERA GROUP COMPANY
Suppressor Capacitors Classes X & Y A KYOCERA GROUP COMPANY Contents General Technical Information on Interference Suppression..... 2 Ordering Code......................................... 3 QX Series
Data sheet FIXED CHIP RESISTORS; RECTANGULAR TYPE & WIDE TERMINATION. AEC-Q200 qualified. RoHS COMPLIANCE ITEM Halogen and Antimony Free
No.: TWMC K HTS-0001 /4 Date: 2017. 4. 21 Data sheet Title: FIXED CHIP RESISTORS; RECTANGULAR TYPE & WIDE TERMINATION Style: TWMC32, 50, 63 AEC-Q200 qualified RoHS COMPLIANCE ITEM Halogen and Antimony
S P E C I F I C A T I O N S
TO : 2009-09-14 S P E C I F I C A T I O N S PRODUCT : CERAMIC CAPACITOR MODEL : DA (X1,Y1) SERIES Manufacturer Customer WRITTEN CHECKED APPROVED WRITTEN CHECKED APPROVED 9/14 9/14 9/14 / / / DONG IL ELECTRONICS
TEST CERTIFICATES OR REPORTS ISSUED BY VEIKI-VNL LTD.
Page 2 of 29 TEST CERTIFICATES OR REPORTS ISSUED BY LTD. Type Test Certificate of Complete Type Test This certificate provides the verification of all the rated characteristics of the equipment as assigned
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life 38 AML 0 ASM smaller dimensions Fig. QUICK REFERENCE DATA DESCRIPTION Nominal case sizes (Ø D x L in mm) 6.3 x.7 to 0 x 5 VALUE 0 x 30 to x 38
Aluminum Electrolytic Capacitors Radial Semi-Professional
Aluminum Electrolytic Capacitors Radial Semi-Professional 03 RLC low leakage current 8 RUS higher CV- values miniaturized 038 RSU ig. longer life RLL QUICK REERENCE DATA DESCRIPTION VALUE Nominal case
DATA SHEET POSITIVE TEMPERATURE COEFFICIENT AC/DC POWER SUPPLY SMD0603 series
Product specification November 05, 201 V.0 DATA SHEET AC/DC POWER SUPPLY series RoHS compliant & Halogen free 2 Positive Temperature Coefficient (PTC) Data Sheet Description The 0603 series provides miniature
Aluminum Capacitors SMD (Chip) Long Life Vertical
Aluminum Capacitors SMD (Chip) Long Life Vertical FEATURES Polarized aluminum electrolytic capacitors, non-solid electrolyte, self healing SMD-version with base plate, vertical construction requiring minimum
WK25V, WK20V, WK12V, WK08V, WK06V. Thick Film High Voltage Chip Resistors. Size 2512, 2010,1206, 0805, 0603
WK25V, WK20V, WK12V, WK08V, WK06V ±5%, ±2%, ±1%, ±0.5% Thick Film High Voltage Chip Resistors Size 2512, 2010,1206, 0805, 0603 *Contents in this sheet are subject to change without prior notice. Page 1
Thermal-Magnetic Circuit Breaker 2210-T2...
Thermal-Magnetic Circuit Breaker 0-T... Description One, two and three pole thermal-magnetic circuit breakers with trip-free mechanism and toggle actuation (S-type TM CBE to EN 6094/IEC 94). Featuring
DATA SHEET General Purpose Thick Film Chip Resistor CR Series
Towards Excellence in Quality, Service & Innovation DATA SHEET General Purpose Thick Film Chip Resistor 1% TO 5%, TCR -200 TO +600 SIZE: 01005/0201/0402/0603/0805/1206/1210/2010/2512 RoHs Compliant Jan
Interference Suppression Film Capacitor - Class X1 Radial MKP 440 V AC - Standard Across the Line
Interference Suppression Film Capacitor - Class X1 Radial MKP 440 V AC - Standard Across the Line FEATURES 15 mm to 27.5 mm lead pitch 440 V rated AC voltage Material categorization: For definitions of
BASE. Rotary limit switch. OptiOnS. FEAtuRES. CERtiFiCAtiOnS
Rotary limit switch BASE Rotary limit switch used to control and measure the movement of industrial machines. Its compact size make it suitable for use in narrow spaces. FEAtuRES It consists of a gear
ELINEMK Technical Characteristics Rated Current Busbar Code Standards Rated Isolation Voltage Max. Rated Operational Voltage Rated Frequency Pollution Degree Protection Degree External Mechanical Impacts
Distributing Tomorrow s Technologies For Today s Designs Toll-Free:
2W, Ultra-High Isolation DIP, Single & DC/DC s Key Features Low Cost 6 Isolation MTBF > 6, Hours Short Circuit Protection Input, and 24 Output,, 1, {, { and {1 Regulated Outputs Low Isolation Capacitance
Overload Relays. SIRIUS 3RU1 Thermal Overload Relays. 3RU11 for standard applications. 5/46 Siemens LV 1 AO 2011
SIRIUS 3RU1 Thermal Overview 1 2 7 3 4 6 "Increased safety" type of EEx e according to ATEX directive 94/9/EC The 3RU11 thermal overload relays are suitable for the overload of explosion-proof motors with
handbook, 050/052 4 columns smaller
4/5 PED-ST FEATURES Polarized aluminium electrolytic capacitors, non-solid Large types, cylindrical aluminium case, insulated with a blue sleeve Also available in bolt version (PED-STB) Pressure relief
SUBMINIATURE MICROSWITCHES - PREMIUM
0/08 SUBMINIATUE MICOSWITCHES - PEMIUM V - 870 High precision flexible leaf snap-action mechanism Operation without balance-point, even at extremely slow actuating speed atings from ma Vc up to (6) A 0
Magnetic and Hydraulic-Magnetic Circuit Breaker 8340-T...
Magnetic and Hydraulic-Magnetic Circuit Breaker 830-T... Description ngle, two and three pole magnetic and hydraulic-magnetic circuit breakers with trip-free mechanism and toggle actuation. A choice of
FLT5A FLT5A. abc. abc. Thermometer User Guide. Thermometer User Guide. Internet:
abc instruments international FLT5A Thermometer Land Instruments International Dronfield, S18 1DJ England Telephone: (1246) 417691 Facsimile: (1246) 41585 Email: infrared.sales@landinst.com Internet: www.landinst.com
Aluminum Electrolytic Capacitors Axial High Temperature High Voltage for E.L.B.
Aluminum Electrolytic Capacitors Axial High Temperature High Voltage for E.L.B. 04-043 ASH standard 04/043 AHH-ELB 550 V/4 h Fig. 85 C 04/043 AMH-ELB 550 V/4 h FEATURES Useful life: 0 000 h at 05 C Stable
Current Sensing Resistors FBF Series Metal Paste Type High Power Lead Free Chip Resistors
1. SCOPE 1.1 Purpose Current Sensing Resistors Fixed Thick-Film Metal Paste High-Power Chip Resistors. Rated power up to 2W and apply to Current Sensing in : Consumer Electronics SMPS M/B BTC Portable
3-TERMINAL 0.1A NEGATIVE VOLTAGE REGULATOR
3-TERMINAL A NEGATIE OLTAGE REGULATOR FEATURES Output Current Up to 1 No External Components Internal Thermal Overload Protection Internal Short-Circuit Limiting Output oltage of 5, 6, 8, 9, 12, 15, 18
Varius SUMMARY OF MODELS OF HRC FUSE-LINKS
SUMMARY OF MODELS OF HRC FUSE-LINKS Type PNA000 PHNA000 PNA00 PHNA00 Rated current I n up to A up to 0 A up to A up to 0 A Rated voltage U n AC 00 V, 00 V 90 V 00 V 90 V DC 0 V 0 V 0 V 0 V Fuse-link size
Semiconductor (AC) fuses
BS88 Fuses x1, 17x9, X17x9, 6 VAC EXTREMELY HIGH BREAKING CAPACITY FUSES: PROTECTION OF POWER SEMICONDUCTORS AS PER IEC STANDARD 6069.1 AND 6 V VOLTAGE RATING COMPLYING WITH IEC GR CLASS (RATINGS FROM
MAU100 Series. 1W, Miniature SIP, Single & Dual Output DC/DC Converters MINMAX. Block Diagram. Key Features
MAU Series W, Miniature SIP, Single & DC/DC s Key Features Efficiency up to 0 Isolation MTBF >,000,000 Hours Low Cost Input,, and Output 3.3,,9,,,{,{9,{ and { Temperature Performance -0 to UL 9V-0 Package
High-ohmic/high-voltage resistors
FEATURES These resistors meet the safety requirements of: UL1676 (range 510 kω to 11 MΩ) EN60065 BS60065 (U.K.) NFC 92-130 (France) VDE 0860 (Germany) High pulse loading capability Small size. APPLICATIONS
To order, specify : Types Protection functions Current surge Asymmetry and loss of phase. Operating principle
otor protection relays - T - FWIT Since % of -phase motor failures are due to load problems or loss of phase, the CROUZET range of motor protection relays is indispensable! models give motor protection
METALLIZED POLYPROPYLENE AC FILTERING CAPACITORS
METALLIZED POLYPROPYLENE AC FILTERING CAPACITORS Technology looking ahead With the new LNF series a new level of safety for the AC capacitors has been reached: Active safety: When the capacitor is stressed
Features : Protection type : Hiccup mode, recovers automatically after fault condition is removed
.. 1W Quad Output with PFC Function Q P-1 s e ries RIPPLE NOISE (max.) Note. VOLTAGE TOLERANCE Note. HARMONIC CURRENT 9 ~ 6VAC 17 ~ VDC 7 ~ 6Hz PF>.95/VAC PF>.98/115VAC at full load 7% 75% 7%.5A/115VAC
AN78Lxx/AN78LxxM Series
oltage Regulators AN78Lxx/AN78LxxM Series -pin positive output voltage regulator ( type) Overview The AN78Lxx series and the AN78LxxM series are - pin fixed positive output type monolithic voltage regulator.
Characteristics and Definitions Used for Film Capacitors
Characteristics and Definitions Used for Film Capacitors COMMON FILM DIELECTRICS USED IN FILM CAPACITORS PRODUCTS PARAMETER DIELECTRIC (1) UNIT Dielectric constant 1 khz 3.3 3 3. - Dissipation factor 1
CR-PF Series Ultra-Low Lead Content Thick Film Resistor
RoHS COMPLIANT** & HALOGEN FREE*** 102 Features n Ultra-low lead (Pb) content* n Green technology n High reliability and stability n Thick film paste on high grade ceramic substrate n RoHS compliant**
Class 1, 100 V (DC) (flanged types) Miniature ceramic plate capacitors
FEATURES High-frequency circuits Temperature compensating High stability Space saving. APPLICATIONS In a great variety of electronic circuits, e.g. in filters and tuning circuits where high stability and/or
5 V/10 V Low Drop Voltage Regulator TLE 4266
5 /1 Low Drop oltage Regulator TLE 266 Features Output voltage 5 or 1 Output voltage tolerance ±2% 12 ma current capability ery low current consumption Low-drop voltage Overtemperature protection Reverse
CM1117F 1A LOW DROPOUT VOLTAGE REGULATOR
GENERAL DESCRIPTION FEATURES The series of adjustable and fixed voltage regulators are designed to provide 1A for applications requiring high efficiency. All internal circuitry is designed to operated
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer GO-SMS/SP3 series I P N = 10... 30 A Ref: GO 10-SMS/SP3, GO 20-SMS/SP3, GO 30-SMS/SP3 For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the
TLP250 TLP250. Transistor Inverter Inverter For Air Conditioner IGBT Gate Drive Power MOS FET Gate Drive. Truth Table
TOSHIB Photocoupler Gals Ired & Photo IC TLP20 Transistor Inverter Inverter For ir Conditioner IGBT Gate Drive Power MOS FET Gate Drive Unit in mm The TOSHIB TLP20 consists of a Gals light emitting diode
ct m ive p 5/EC Thermal cut-outs
RoHS Compliant Directive //EC Marking of switches type: AM, AF, AB,, AA. AM0. 0. 0 0/0 -. 0 Strip length Second conductor length First conductor length Type of thermal cut-out Rated switching temperature
MAU200 Series. 1W, High Isolation SIP, Single & Dual Output DC/DC Converters MINMAX. Block Diagram. Key Features
Component Distributors, Inc. ~ www.cdiweb.com ~ sales@cdiweb.com ~ -0--33 W, High Isolation SIP, Single & DC/DC s Key Features Efficiency up to 00 Isolation MTBF >,000,000 Hours Low Cost Input, and Output
Periodic Inspection and Testing of Electrical Installations Sample Test ( ) Version 1.3 July 2018
Periodic Inspection and Testing of Electrical Installations Sample Test (2391-051) Version 1.3 July 2018 Sample Questions Version and date Change detail Section 1.3 July 2018 Modified questions/answers
W_CS-1W5/3W Series. Features. General Description. Functional Diagram. EMC Solution-Recommended Circuit
W_-W/W Series Features u Operating temperature: -40 to + u 4.-/-/-/-/-/- input u V/V/V/V/V/±V/±V/±V/±V output u iciency up to % u Ultra-low noise & ripple u Bare module meet CISPR/EN0 Class B u % burn-in
TCET110.(G) up to TCET4100. Optocoupler with Phototransistor Output. Vishay Telefunken. Description. Applications. VDE Standards
Optocoupler with Phototransistor Output Description The TCET11./ TCET2/ TCET4 consists of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 4-lead up to 16-lead plastic
Zelio Relay - Solid State Relays
Selection guide SSR solid state relays Applications Panel mounted PF00--Q Contact type N/O SPST contact Control voltage ranges a 0 0 V c V Operating voltages a 0 V, 0 V, 0 V Type of switching a Zero voltage
MAU100 Series. 1W, Miniature SIP, Single & Dual Output DC/DC Converters MINMAX. Key Features
W, Miniature SIP, Single & Dual Output DC/DC s Key Features Efficiency up to % 000 Isolation MTBF >,000,000 Hours Low Cost Input,, and Output 3.3,,9,,,{,{9,{ and { Temperature Performance -0] to +] UL
FMS series Metal Strip Shunt Lead Free Current Sensing Resistors
1. Features......2 2. Applications...... 2 3. Dimension and construction.. 2 4. Power Derating Curve....3 5. Rating.3 6. Part Number.. 3 7. Marking / Soldering..4 8. Reliability Performance..5 9. Packing.
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC FEATURES Complying with IEC 60384-14 4 th edition Can pass 10 kv pulses (10 per polarity) Withstands 85 / 85 / 1000 h test Reduced
Characteristics Climatic Category 40/105/56 (IEC 61071)
Polypropylene Film Capacitors for Snubber Applications Features - Very low dissipation factor - High peak pulse capability - Plates for direct IGBT connection - Self-healing - 105 C CBB 165 IS Series Applications
52- Inner Taping dimension or 73- Inner Taping dimension ZB- Z version. UL = UL Version YY = Standard
Precision Fusible safety Wirewound Resistors Axial and SMD Version Ceramic core Flame retardant coating UL42 Recognized (file E330640) ORDERING CODE-Example New SAP Part Nr.: CRF 300 J T - 73-50R UL Serie
List... Package outline... Features Mechanical data... Maximum ratings... Rating and characteristic curves... Pinning information...
List List... Package outline... 1 Features... Mechanical data... Maximum ratings... Rating and characteristic curves... 3 Pinning information... 4 Marking... 4 Tube packing... 4 Suggested thermal profiles
handbook, 2 columns handbook, halfpage 085 CS
FEATURES Polarized aluminium electrolytic capacitors, non-solid, self healing handbook, 2 columns SMD-version, rectangular case, insulated Miniaturized, high CV per unit volume, low height Flexible terminals,
DATA SHEET. 048 RML Aluminum electrolytic capacitors Radial Miniature Long-Life. BCcomponents
DATA SHEET Supersedes data of January 998 File under, BC0 000 Jan 8 FEATURES Polarized aluminum electrolytic capacitors, non-solid electrolyte Radial leads, cylindrical aluminum case with pressure relief,
NTC Thermistor:TTF Type
Features 1. RoHS compliant 2. Radial leaded insulation film coated 3. -40 ~ +100 operating temperature range 4. Agency recognition: UL /cul Recommended Applications 1. Home appliances (air conditioner,
Characteristics Climatic Category 40/105/56 (IEC 61071)
Polypropylene Film Capacitors for Snubber Applications Features - 105 C - Very low dissipation factor - Highest peak pulse capability - Double-sided metallized electrodes - Internal series connection -