Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed.

Size: px
Start display at page:

Download "Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed."

Transcription

1 ARCH 631 Note Set 11 S017abn Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed. Building description The building is a three-story office building intended for speculative rental. Figure presents a full-building section and a plan of the upper floor. The exterior walls are permanent. The design is a rigid perimeter frame to resist lateral loads. Loads (UBC 1994) Live Loads: Roof: 0 lb/ Floors: Office areas: 50 lb/ (.39 kpa) Corridor and lobby: 100 lb/ (4.79 kpa) Partitions: 0 lb/ (0.96 kpa) Wind: map speed of 80 mph (190 km/h); exposure B Assumed Construction Loads: Floor finish: 5 lb/ (0.4 kpa) Ceilings, lights, ducts: 15 lb/ (0.7 kpa) Walls (average surface weight): Interior, permanent: 10 lb/ (0.48 kpa) Exterior curtain wall: 15 lb/ (0.7 kpa) Materials Use f c =3000 psi (0.7 MPa) and grade 60 reinforcement (fy = 60 ksi or 414 MPa). 49

2 ARCH 631 Note Set 11 S017abn Structural Elements/Plan Case 1 is shown in Figure (framing plan) and consists of a flat plate supported on interior beams, which in turn, are supported on girders supported by columns. We will examine the slab, and a four-span interior beam. Case will consider the bays with flat slabs, no interior beams with drop panels at the columns and an exterior rigid frame with spandrel (edge) beams. An example of an edge bay is shown to the right. We will examine the slab and the drop panels. For both cases, we will examine the exterior frames in the 3-bay direction. Case 1: Slab: The slabs are effectively 10 x 30, with an aspect ratio of 3, making them one-way slabs. Minimum depths (by ACI) are a function of the span. Using Table for one way slabs the minimum is and there is a 5 inches minimum for fire rating. l n 8 (Found in Note Set 10.1) We ll presume the interior beams are 1 wide, so ln = 10 - ½ - ½ = 9 minimum t (or h) in/ in 8 Use 5 in. based on fire rating. dead load from slab (self weight) = t 3 lb/ in/ 1 in = 6.5 lb/ 50

3 ARCH 631 Note Set 11 S017abn total dead load = ( ) lb/ + of lightweight concrete topping with weight of 18 lb/ (0.68 KPa) (presuming interior wall weight is over beams & girders) dead load = lb/ live load (critical case in corridor) = 100 lb/ total factored distributed load (ASCE-7) of 1.D+1.6L: wu = 1.(100.5 lb/ ) + 1.6(100 lb/ ) = 80.6 lb/ Maximum Positive Moments from Figure -3 (Note Set 8.1), end span (integral with support) for a 1 wide strip: Mu (positive) = w u 14 lb / n n wu 1 14 (80.6 )(1 )(9 14 ) 1k 1000lb = 1.6 k- Maximum Negative Moments from Figure -5 (Note Set 8.1), end span (integral with support) for a 1 wide strip: Mu-(negative) = w u 1 n w u 1 1 n (80.6 lb / )(1 )(9 1 ) 1k = 1.89 k- 1000lb 51

4 (tensile strain of 0.004) In Note Set10.1 ARCH 631 Note Set 11 S017abn The design aid (Figure of Note Set 10.1) can be used to find the reinforcement ratio,, knowing Rn = Mn/bd with Mn = Mu/f, where f = 0.9 (because = ). We can presume the effective depth to the centroid of the reinforcement, d, is 1.5 less than the slab thickness (with ¾ cover and ½ of a bar diameter for a #4 (1 ) bar) = 4. Rn = M bd 1.89 (0.9)(1 )(3.75 ) k u in/ lb/ k psi in in so for f c = 3000 psi and fy = 60,000 psi is the minimum. For slabs, As minimum is bt for grade 60 steel. (See Note Set 10.1) As = bt = (1in)(5in) = in / (Full table found in Note Set 10.1) 5

5 ARCH 631 Note Set 11 S017abn Pick bars and spacing off Table 3-7. Use #3 1 in (As = 0.11 in ). Common chart of spaced bars based on bar areas. Check the moment capacity. d is actually 5 in 0.75in (cover) ½ (3/8in bar diameter) = 4.06 in a = Asfy/0.85f cb = 0.11 in (60 ksi)/[0.85(3 ksi)1 in] = 0. in Mn = Asfy(d-a/) = 0.in 1 0.9(0.11 in )(60 ksi)(4.06 in ) ( ) 1.96 k- > 1.89 k- needed 1 in (OK) Provide steel in the perpendicular direction as well, and make certain not to exceed the minimum spacings of 5t or 18" for shrinkage and crack control steel or 3t or 18" for flexure reinforcement (in found in Note Set 10.1). Maximum Shear: Figure -7 (Note Set 8.1) shows end shear that is wuln/ except at the end span on the interior column which sees a little more and you must design for 15% increase: lb/ 1.15(80.6 )( 1 )(9 ) Vu-max = 1.15wuln/ = = 145 lb (for a 1 strip) lb/ (80.6 )( 1 )(4.06 in) Vu at d away from the support = Vu-max w(d) = 145 lb in/ 1 = 1357 lb 53

6 ARCH 631 Note Set 11 S017abn Check the one way shear capacity: vvc = v f c bd (v = 0.75, =1.0 for normal weight concrete): in in vvc = 0.75()(1.0) 3000 psi (1 )(4.06 ) = 4003 lb Is Vu (needed) < vvc (capacity)? thicker. YES: 1357 lb 4003 lb, so we don't need to make the slab Interior Beam (effectively a T-beam): Tributary width = 10 for an interior beam. dead load = area load x tributary width = (100.5 lb/ )(10) = 1005 lb/ (14.7 kn/m) Reduction of live load is allowed (Note Set 3.4), with a live load element factor, KLL, of for an interior beam for its tributary width assuming the girder is 1 wide. The live load is 100 lb/ (corridors and lobbies): L = 15 lb 15 L (0.5 ) = 100 o (0.5 ) = 87.3 lb/ KLL A (30 1 )(10 ) T (Reduction Multiplier = > 0.5) live load = 87.3 lb/ (10) = 873 lb/ (1.7 kn/m) Estimating a 1 wide x 4 deep beam means the additional dead load from self weight can be included. The top 5 inches of slab has already been included in the dead load (1005 lb/): dead load from self weight = lb (1 in wide)(4 5 in deep) t tributary width = 1 1in = 37.5 lb/ (3.46 kn/m) wu = 1.(1005 lb/+37.5 lb/) + 1.6(873 lb/) = 888 lb/ (4.30 kn/m) 54

7 ARCH 631 Note Set 11 S017abn The effective width, be, of the T part is the smaller of Set 10.1): n 4, b w 16t, or center-center spacing (Note be = minimum{9 /4 = 7.5 = 87 in, 1 in + 16x5 in = 9 in, 10 = 10 in} = 87 in The clear span for the beam is ln = 30 - ½ - ½ = 9 Maximum Positive Moments from Figure -3 (Note Set 8.3), end span (integral with support): Mu (positive) = lb/ wu n 888 (9 ) 1k = k lb Maximum Negative Moments from Figure -4 (Note Set 8.1), end span (integral with support): Mu-(negative) = w u 10 n 888 lb / (9 10 ) 1k = 4.9 k- 1000lb Figure (5) can be used to find an approximate for top reinforcement if Rn = Mn/bd and we set Mn = Mu/f. We can presume the effective depth is.5 less than the 4 depth (for 1.5 cover and ½ bar diameter for a #10 (10/8) bar + #3 stirrups (3/8 more)), so d = 1.5. Rn = M bd f lb/ k k u in in 0.9 (1 )(1.5 ) 1 in/ = 584 psi so for f c = 3000 psi and fy = 60,000 psi is about (and less than max = ) Then we pick bars and spacing off Table 3-7 (pg. 53) to fit in the effective flange width in the slab. 55

8 ARCH 631 Note Set 11 S017abn For bottom reinforcement (positive moment) the effective flange is so wide at 87 in, that it resists a lot of compression, and needs very little steel to stay under-reinforced (a is between 0.6 and 0.5 ). We d put in bottom bars at the minimum reinforcement allowed and for tying the stirrups to. Maximum Shear: Vmax = wul/ normally, but the end span sees a little more and you must design for 15% increase. But for beams, we can use the lower value of V that is a distance of d from the face of the support (see Figure.7 on page 53): Vu-design = 1.15wuln/ wud= lb/ lb/ in 1.15(888 )(9 ) 888 (1.5 ) 1 in/ 4,983 lb = 43.0 k Check the one way shear capacity = vvc = v f c bd, where v 0.75 and = 1.0 in in vvc = 0.75()(1.0) 3000 psi (1 )(1.5 ) = 1,197 lb = 1. k Is Vu (needed) < vvc (capacity)? NO: 43.0 k is greater than 1. k, so stirrups are needed vvs = Vu -vvc = 43.0 k 1. k = 1.8 k (max needed) Using #3 bars (typical) with two legs means Av = (0.11in ) = 0. in. (Found in Note Set 10.1) To determine required spacing, use Table 3-8 (pg. 57). For d = 1.5 and vvs v4 v4 c f c bd (where f bd= = (1. k) = 4.4 k when λ=1.0), the maximum spacing is d/ = in. or 4. V c srequired = Av f ytd Av f ytd V V V u c s = in ksi in k 1.8 = 9.75 in, so use 9 in. We would try to increase the spacing as the shear decreases, but it is a tedious job. We need stirrups anywhere that Vu > vvc/. One recommended intermediate spacing is d/3. 56

9 ARCH 631 Note Set 11 S017abn greater of and smaller of and (ACI ) (ACI 0...4) must also be considered (ACI ) The required spacing where stirrups are needed for crack control (vvc Vu > ½vVc ) is srequired = smaller of Af v yt 0.in (60,000psi) 50b = in and Af v yt 0.in (60,000psi) 50(1 in) 0.75 fb psi(1 in) w maximum spacing is d/ = in. or 4. Use 10 in. c w = 6.8 in, and the A recommended minimum spacing for the first stirrup is in. from the face of the support. A distance of one half the spacing near the support is oen used. Vu 36.7 k 41.9 k to find distances when w is known: x = (peak crossing value)/w ex: 41.9 k 1. k)/.888 k/ = k 10.6 k 7. = 86 in = 130 in C L 14.5 in 13.0 = 156 in 9.35 = 11 in 10.6 k 1. k x 10 in 10 in 9 in 43.0 k 48. k END SPAN STIRRUP LAYOUT 57

10 spandrel girder ARCH 631 Note Set 11 S017abn Spandrel Girders: Because there is a concentrated load on the girder, the approximate analysis can t technically be used. If we converted the maximum moment (at midspan) to an equivalent distributed load by setting it equal to wul /8 we would then use: Maximum Positive Moments from Figure -3 (pg. 51), end span (integral with support): Mu+ = w u 14 n Maximum Negative Moments from Figure -4 (pg. 55), end span (column support): Mu- = w u 10 n (with w u 16 n at end) Column: An exterior or corner column will see axial load and bending moment. We d use interaction charts for Pu and Mu for standard sizes to determine the required area of steel. An interior column sees very little bending. The axial loads come from gravity. The factored load combination is 1.D+1.6L + 0.5Lr (Note Set 3.). The girder weight, presuming 1 x 4 girder at 150 lb/ 3 3 is 150 (1 )(4 ) = 600 lb/ lb Top story: presuming 0 lb/ roof live load, the total load for an interior column (tributary area of 30 x30 ) is: Lower stories: DLroof*: 1. x lb/ x 30 x 30 * assuming the same dead load and materials as the floors = k DLbeam 1. x 37.5 lb/ x 30 x 3 beams = 5.6 k DLgirder 1. x 600 lb/ x 30 = 1.6 k LLr: 0.5 x 0 lb/ x 30 x 30 = 9.0 k Total = k DLfloor: 1. x lb/ x 30 x 30 DLbeam 1. x 37.5 lb/ x 30 x 3 beams DLgirder 1. x 600 lb/ x 30 LLfloor: 1.6 x (0.873) x100 lb/ x 30 x 30 Total = k = 5.6 k = 1.6 k = 15.7 k (includes reduction) = 81.4 k 58

11 ARCH 631 Note Set 11 S017abn Summary: nd floor column sees Pu = = k 1 st floor column sees Pu = = 77.5 k Look at the example interaction diagram for an 18 x 18 column (Figure 5-0 ACI 318-0) using f c = 4000 psi and fy = 60,000 psi for the first floor having Pu = 77.5 k, and Mu to the column being approximately 10% of the beam negative moment = 0.1*4.9 k- = 4.3 k-: (See maximum negative moment calculation for an interior beam.) The chart indicates the capacity for the reinforcement amounts shown by the solid lines. For Pu = 77.5 k and Mu = 4.3 k-, the point plots below the line marked 4-#11 (1.93% area of steel to an 18 in x 18 in area). 59

12 ARCH 631 Note Set 11 S017abn Lateral Force Design: The wind loads from the wind speed, elevation, and exposure we ll accept as shown in Figure 17.4 given on the le in psf. The wind is acting on the long side of the building (see pg. 49). The perimeter frame resists the lateral loads, so there are two with a tributary width of ½ [(30)x(4 bays) + for beam widths and cladding] = 1/ = 61 The factored combinations with dead and wind load are: 1.D +1.6Lr + 0.5W 1.D + 1.0W + L + 0.5Lr The tributary height for each floor is half the distance to the next floor (top and bottom): Exterior frame (bent) loads: lb/ H1 = 195 (61 ) =11,895 lb = 11.9 k/bent H = lb/ 34 (61 ) =14.3 k/bent lb/ k H3 = 1000 lb/ 7 (61 ) =13.8 k/bent lb/ k 1000 Using Multiframe, the axial force, shear and bending moment diagrams can be determined using the load combinations, and the largest moments, shear and axial forces for each member determined. 60

13 ARCH 631 Note Set 11 S017abn M = 03.7 k- V = 6.6 k P = 54.7 k M =190.8 k- V = 8.0 k P = 11.6 k M = 18.8 k- V = 45.4 k P = 6.6 k M = V = 60.5 k P = 1.9 k M = k- V = 60.9 k P = 6.5 k M = 39.3 k- V = 4.7 k P = 91.0 k M = 70. k- V = 9. k P = 15.5 k M = 37.8 k- V = 45.5 k P = 8.9 k M = k- V = 60.0 k P = 6.4 k M = k- V = 61.0 k P = 4.1 k M = 3.4 k- V = 3.7 k P =91.0 k M = 51.1 k- V = 7.7 k P = 15.7 k M = 36.3 k- V = 46.6 k P = 30.8 k M = k- V = 59.7 k P = 10.4 k M = k- V = 6.0 k P = 1.6 k M = k- V = 4.8 k P = 53.5 k M = 14.7 k- V = 1. k P = 10.3 k M = k- V = 1.6 k P = 19.8 k M = k- V = 11.6 k P = k M = 95.5 k- V = 10.3 k P = k M =10.6 k- V = 8.5 k P = k (This is the summary diagram of force, shear and moment magnitudes refer to the maximum values in the column or beams, with the maximum moment in the beams being negative over the supports, and the maximum moment in the columns being at an end.) Axial force diagram: Shear diagram: Bending moment diagram: Displacement: 61

14 ARCH 631 Note Set 11 S017abn Beam-Column loads for design: The bottom exterior columns see the largest bending moment on the lee-ward side (le): Pu = 19.8 k and Mu = k- (with large axial load) The interior columns see the largest axial forces: Pu = k and Mu = 95.5 k- and Pu = k and Mu = k- Refer to an interaction diagram for column reinforcement and sizing. Case Slab: The slabs are effectively 30 x 30, making them two-way slabs. Minimum thicknesses (by ACI) are a function of the span. Using Table 4-1 (Note Set 8.1) for two way slabs, the minimum is the larger of ln/36 or 4 inches. Presuming the columns are 18 wide, ln = 30 ½(18 in)/(1 /in) ½(18 in)/(1 /in) = 8.5, h = ln/36 = (8.5x1)/36 = 9.5 in The table also says the drop panel needs to be l/3 long = 8.5 /3 = 9.5, and that the minimum depth must be 1.5h = 1.5(9.5 in) = 1 in. 6

15 ARCH 631 Note Set 11 S017abn For the strips, l = 30, so the interior column strip will be 30 /4+30/4 = 15, and the middle strip will be the remaining 15. lb/ in dead load from slab = t = lb/ in/ 1 3 total dead load = lb/ + of lightweight concrete 18 lb/ (0.68 KPa) (presuming interior wall weight is over beams & girders) total dead load = = = lb/ live load with reduction (Note Set 3.4), where live load element factor, KLL, is 1 for a two way slab: 15 L = (0.5 ) lb 15 Lo = 100 (0.5 ) = 75 lb/ K A 1(30 )(30 ) LL T total factored distributed load: wu = 1.( lb/ ) + 1.6(75 lb/ ) = lb/ total panel moment to distribute: Mo = lb/ wul ln (30 )(8.5 ) 1k = k lb Column strip, end span: Maximum Positive Moments from Table 4-3 (Note Set 8.1), (flat slab with spandrel beams): Mu+ = 0.30Mo = 0.30(938.4 k-) = 81.5 k- Maximum Negative Moments from Table 4-3 (Note Set 8.1), (flat slab with spandrel beams): Mu- = 0.53Mo = 0.53(938.4 k-) = k- 63

16 ARCH 631 Note Set 11 S017abn Middle strip, end span: Maximum Positive Moments from Table 4-3 (Note Set 8.1), (flat slab with spandrel beams): Mu+ = 0.0Mo = 0.0(938.4 k-) = k- Maximum Negative Moments from Table 4-3 (Note Set 8.1), (flat slab with spandrel beams): Mu- = 0.17Mo = 0.17(938.4 k-) = k- Design as for the slab in Case 1, but provide steel in both directions distributing the reinforcing needed by strips. 64

17 ARCH 631 Note Set 11 S017abn Shear around columns: The shear is critical at a distance d/ away from the column face (Note Set 10.1). If the drop panel depth is 1 inches, the minimum d with two layers of 1 diameter bars would be 1 ¾ (cover) (1 ) ½(1 ) =about 9.75 in (to the top steel). (Note Set column shear perimeter tributary area for column drop panel The shear resistance is vvc = v4 f c bod, 0.75 v and =1.0 where bo, is the perimeter length. The design shear value is the distributed load over the tributary area outside the shear perimeter, Vu = wu (tributary area - b1 x b) where b s are the column width plus d/ each side. b1 = b = / / = 7.75 in b1 x b = 1 (7.75 in) ( ) = in Vu = lb/ 1k (84.7 )( ) = 54.7 k 1000 lb Shear capacity: bo = (b1) + (b) = 4(7.75 in) = 111 in in in vvc = (1.0) 3000 psi = 177,83 lb= ksi < Vu! The shear capacity is not large enough. The options are to provide shear heads or a deeper drop panel, or change concrete strength, or even a different system selection... There also is some transfer by the moment across the column into shear. 65

18 ARCH 631 Note Set 11 S017abn Deflections: Elastic calculations for deflections require that the steel be turned into an equivalent concrete material using n = E E For normal weight concrete (150 lb/ 3 ): s c. Ec can be measured or calculated with respect to concrete strength. Ec = 57, psi = 3,1,019 psi = 31 ksi E c 57, 000 f (Note Set 10.1) c n = 9,000 psi/31 ksi = 9.3 Deflection limits are given in Table

Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed.

Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed. ARCH 631 Note Set 11 F015abn Case Study in Reinfored Conrete adapted from Simplified Design of Conrete Strutures, James Ambrose, 7 th ed. Building desription The building is a three-story offie building

More information

Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed.

Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed. ARCH 631 Note Set 11 F013abn Case Stdy Refored Conrete adapted from Simplified Design of Conrete Strtres, James Ambrose, 7 th ed. Bildg desription The bildg is a three-story offie bildg tended for spelative

More information

Figure 1: Representative strip. = = 3.70 m. min. per unit length of the selected strip: Own weight of slab = = 0.

Figure 1: Representative strip. = = 3.70 m. min. per unit length of the selected strip: Own weight of slab = = 0. Example (8.1): Using the ACI Code approximate structural analysis, design for a warehouse, a continuous one-way solid slab supported on beams 4.0 m apart as shown in Figure 1. Assume that the beam webs

More information

Lecture 7 Two-Way Slabs

Lecture 7 Two-Way Slabs Lecture 7 Two-Way Slabs Two-way slabs have tension reinforcing spanning in BOTH directions, and may take the general form of one of the following: Types of Two-Way Slab Systems Lecture 7 Page 1 of 13 The

More information

Design of Reinforced Concrete Structures (II)

Design of Reinforced Concrete Structures (II) Design of Reinforced Concrete Structures (II) Discussion Eng. Mohammed R. Kuheil Review The thickness of one-way ribbed slabs After finding the value of total load (Dead and live loads), the elements are

More information

Sway Column Example. PCA Notes on ACI 318

Sway Column Example. PCA Notes on ACI 318 Sway Column Example PCA Notes on ACI 318 ASDIP Concrete is available for purchase online at www.asdipsoft.com Example 11.2 Slenderness Effects for Columns in a Sway Frame Design columns C1 and C2 in the

More information

UC Berkeley CE 123 Fall 2017 Instructor: Alan Kren

UC Berkeley CE 123 Fall 2017 Instructor: Alan Kren CE 123 - Reinforced Concrete Midterm Examination No. 2 Instructions: Read these instructions. Do not turn the exam over until instructed to do so. Work all problems. Pace yourself so that you have time

More information

Serviceability Deflection calculation

Serviceability Deflection calculation Chp-6:Lecture Goals Serviceability Deflection calculation Deflection example Structural Design Profession is concerned with: Limit States Philosophy: Strength Limit State (safety-fracture, fatigue, overturning

More information

DL CMU wall = 51.0 (lb/ft 2 ) 0.7 (ft) DL beam = 2.5 (lb/ft 2 ) 18.0 (ft) 5

DL CMU wall = 51.0 (lb/ft 2 ) 0.7 (ft) DL beam = 2.5 (lb/ft 2 ) 18.0 (ft) 5 SUJECT: HEADER EAM SELECTION SHEET 108 of 131 INTERIOR HEADER EAM SELECTION - ay length = 36 ft. (stairwell) INTERIOR HEADER EAM Header eam 1 2 Total ay Length = 36 (ft) Total ay Width = 10 (ft) 20.5 Fill

More information

Lecture-08 Gravity Load Analysis of RC Structures

Lecture-08 Gravity Load Analysis of RC Structures Lecture-08 Gravity Load Analysis of RC Structures By: Prof Dr. Qaisar Ali Civil Engineering Department UET Peshawar www.drqaisarali.com 1 Contents Analysis Approaches Point of Inflection Method Equivalent

More information

Design of a Multi-Storied RC Building

Design of a Multi-Storied RC Building Design of a Multi-Storied RC Building 16 14 14 3 C 1 B 1 C 2 B 2 C 3 B 3 C 4 13 B 15 (S 1 ) B 16 (S 2 ) B 17 (S 3 ) B 18 7 B 4 B 5 B 6 B 7 C 5 C 6 C 7 C 8 C 9 7 B 20 B 22 14 B 19 (S 4 ) C 10 C 11 B 23

More information

PUNCHING SHEAR CALCULATIONS 1 ACI 318; ADAPT-PT

PUNCHING SHEAR CALCULATIONS 1 ACI 318; ADAPT-PT Structural Concrete Software System TN191_PT7_punching_shear_aci_4 011505 PUNCHING SHEAR CALCULATIONS 1 ACI 318; ADAPT-PT 1. OVERVIEW Punching shear calculation applies to column-supported slabs, classified

More information

Chapter 2. Design for Shear. 2.1 Introduction. Neutral axis. Neutral axis. Fig. 4.1 Reinforced concrete beam in bending. By Richard W.

Chapter 2. Design for Shear. 2.1 Introduction. Neutral axis. Neutral axis. Fig. 4.1 Reinforced concrete beam in bending. By Richard W. Chapter 2 Design for Shear By Richard W. Furlong 2.1 Introduction Shear is the term assigned to forces that act perpendicular to the longitudinal axis of structural elements. Shear forces on beams are

More information

From Table 1 4. DL = [12 lb/ft 2 # in.(6 in.)] (15 ft)(10 ft) = 10,800 lb. LL = (250 lb/ft 2 )(15 ft)(10 ft) = 37,500 lb.

From Table 1 4. DL = [12 lb/ft 2 # in.(6 in.)] (15 ft)(10 ft) = 10,800 lb. LL = (250 lb/ft 2 )(15 ft)(10 ft) = 37,500 lb. 1 1. The floor of a heavy storage warehouse building is made of 6-in.-thick stone concrete. If the floor is a slab having a length of 15 ft and width of 10 ft, determine the resultant force caused by the

More information

Moment Redistribution

Moment Redistribution TIME SAVING DESIGN AID Page 1 of 23 A 3-span continuous beam has center-to-center span lengths of 30 ft-0 in. The beam is 20 in. by 28 in. and all columns are 20 in. by 20 in. In this example, the beam

More information

ε t increases from the compressioncontrolled Figure 9.15: Adjusted interaction diagram

ε t increases from the compressioncontrolled Figure 9.15: Adjusted interaction diagram CHAPTER NINE COLUMNS 4 b. The modified axial strength in compression is reduced to account for accidental eccentricity. The magnitude of axial force evaluated in step (a) is multiplied by 0.80 in case

More information

Dr. Hazim Dwairi. Example: Continuous beam deflection

Dr. Hazim Dwairi. Example: Continuous beam deflection Example: Continuous beam deflection Analyze the short-term and ultimate long-term deflections of end-span of multi-span beam shown below. Ignore comp steel Beam spacing = 3000 mm b eff = 9000/4 = 2250

More information

twenty one concrete construction: shear & deflection ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture

twenty one concrete construction: shear & deflection ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture twenty one concrete construction: Copyright Kirk Martini shear & deflection Concrete Shear 1 Shear in Concrete

More information

Sabah Shawkat Cabinet of Structural Engineering Walls carrying vertical loads should be designed as columns. Basically walls are designed in

Sabah Shawkat Cabinet of Structural Engineering Walls carrying vertical loads should be designed as columns. Basically walls are designed in Sabah Shawkat Cabinet of Structural Engineering 17 3.6 Shear walls Walls carrying vertical loads should be designed as columns. Basically walls are designed in the same manner as columns, but there are

More information

Design of a Balanced-Cantilever Bridge

Design of a Balanced-Cantilever Bridge Design of a Balanced-Cantilever Bridge CL (Bridge is symmetric about CL) 0.8 L 0.2 L 0.6 L 0.2 L 0.8 L L = 80 ft Bridge Span = 2.6 L = 2.6 80 = 208 Bridge Width = 30 No. of girders = 6, Width of each girder

More information

Lecture-04 Design of RC Members for Shear and Torsion

Lecture-04 Design of RC Members for Shear and Torsion Lecture-04 Design of RC Members for Shear and Torsion By: Prof. Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk www.drqaisarali.com 1 Topics Addressed Design of

More information

SERVICEABILITY LIMIT STATE DESIGN

SERVICEABILITY LIMIT STATE DESIGN CHAPTER 11 SERVICEABILITY LIMIT STATE DESIGN Article 49. Cracking Limit State 49.1 General considerations In the case of verifications relating to Cracking Limit State, the effects of actions comprise

More information

Annex - R C Design Formulae and Data

Annex - R C Design Formulae and Data The design formulae and data provided in this Annex are for education, training and assessment purposes only. They are based on the Hong Kong Code of Practice for Structural Use of Concrete 2013 (HKCP-2013).

More information

B U I L D I N G D E S I G N

B U I L D I N G D E S I G N B U I L D I N G D E S I G N 10.1 DESIGN OF SLAB P R I O D E E P C H O W D H U R Y C E @ K 8. 0 1 7 6 9 4 4 1 8 3 DESIGN BY COEFFICIENT METHOD Loads: DL = 150 pc LL = 85 pc Material Properties: c = 3000

More information

1/29/2010 Page 2 of 65 1/29/2010 Page 3 of 65 1/29/2010 Page 4 of 65 Project Information 1/29/2010 Page 5 of 65 Muckleshoot Indian Tribe Project Number 09-118 West Detention Vault West Vault City of Auburn

More information

A q u a b l u e a t t h e G o l d e n M i l e

A q u a b l u e a t t h e G o l d e n M i l e A q u a b l u e a t t h e G o l d e n M i l e H a t o R e y, P u e r t o R i c o G e n e r a l B u i l d i n g I n f o r m a t i o n Building Facts: 7-story parking structure + luxury apartments 900,000

More information

Assignment 1 - actions

Assignment 1 - actions Assignment 1 - actions b = 1,5 m a = 1 q kn/m 2 Determine action on the beam for verification of the ultimate limit state. Axial distance of the beams is 1 to 2 m, cross section dimensions 0,45 0,20 m

More information

Appendix K Design Examples

Appendix K Design Examples Appendix K Design Examples Example 1 * Two-Span I-Girder Bridge Continuous for Live Loads AASHTO Type IV I girder Zero Skew (a) Bridge Deck The bridge deck reinforcement using A615 rebars is shown below.

More information

Beam Design and Deflections

Beam Design and Deflections Beam Design and Deflections tation: a = name for width dimension A = name for area Areq d-adj = area required at allowable stress when shear is adjusted to include self weight Aweb = area of the web of

More information

Appendix J. Example of Proposed Changes

Appendix J. Example of Proposed Changes Appendix J Example of Proposed Changes J.1 Introduction The proposed changes are illustrated with reference to a 200-ft, single span, Washington DOT WF bridge girder with debonded strands and no skew.

More information

SERVICEABILITY OF BEAMS AND ONE-WAY SLABS

SERVICEABILITY OF BEAMS AND ONE-WAY SLABS CHAPTER REINFORCED CONCRETE Reinforced Concrete Design A Fundamental Approach - Fifth Edition Fifth Edition SERVICEABILITY OF BEAMS AND ONE-WAY SLABS A. J. Clark School of Engineering Department of Civil

More information

Two Way Beam Supported Slab

Two Way Beam Supported Slab Two Way Beam Supported Slab Part 2 The following example was done by Mr. Naim Hassan, 3 rd Year 2 nd Semester Student of CE Dept., AUST 16 The following Example was done by Md. Mahmudun Nobe, ID -.01.03.078,

More information

Two-Way Flat Plate Concrete Floor System Analysis and Design

Two-Way Flat Plate Concrete Floor System Analysis and Design Two-Way Flat Plate Concrete Floor System Analysis and Design Version: Aug-10-017 Two-Way Flat Plate Concrete Floor System Analysis and Design The concrete floor slab system shown below is for an intermediate

More information

Lecture-09 Introduction to Earthquake Resistant Analysis & Design of RC Structures (Part I)

Lecture-09 Introduction to Earthquake Resistant Analysis & Design of RC Structures (Part I) Lecture-09 Introduction to Earthquake Resistant Analysis & Design of RC Structures (Part I) By: Prof Dr. Qaisar Ali Civil Engineering Department UET Peshawar www.drqaisarali.com 1 Topics Introduction Earthquake

More information

Lecture-05 Serviceability Requirements & Development of Reinforcement

Lecture-05 Serviceability Requirements & Development of Reinforcement Lecture-05 Serviceability Requirements & Development of Reinforcement By: Prof Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk www.drqaisarali.com 1 Section 1: Deflections

More information

General Comparison between AISC LRFD and ASD

General Comparison between AISC LRFD and ASD General Comparison between AISC LRFD and ASD 1 General Comparison between AISC LRFD and ASD 2 AISC ASD and LRFD AISC ASD = American Institute of Steel Construction = Allowable Stress Design AISC Ninth

More information

CHAPTER 4. Design of R C Beams

CHAPTER 4. Design of R C Beams CHAPTER 4 Design of R C Beams Learning Objectives Identify the data, formulae and procedures for design of R C beams Design simply-supported and continuous R C beams by integrating the following processes

More information

Example 2.2 [Ribbed slab design]

Example 2.2 [Ribbed slab design] Example 2.2 [Ribbed slab design] A typical floor system of a lecture hall is to be designed as a ribbed slab. The joists which are spaced at 400mm are supported by girders. The overall depth of the slab

More information

3.4 Reinforced Concrete Beams - Size Selection

3.4 Reinforced Concrete Beams - Size Selection CHAPER 3: Reinforced Concrete Slabs and Beams 3.4 Reinforced Concrete Beams - Size Selection Description his application calculates the spacing for shear reinforcement of a concrete beam supporting a uniformly

More information

Slenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A )

Slenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A ) Slenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A23.3-94) Slender Concrete Column Design in Sway Frame Buildings Evaluate slenderness effect for columns in a

More information

Flexure: Behavior and Nominal Strength of Beam Sections

Flexure: Behavior and Nominal Strength of Beam Sections 4 5000 4000 (increased d ) (increased f (increased A s or f y ) c or b) Flexure: Behavior and Nominal Strength of Beam Sections Moment (kip-in.) 3000 2000 1000 0 0 (basic) (A s 0.5A s ) 0.0005 0.001 0.0015

More information

TABLE OF CONTANINET 1. Design criteria. 2. Lateral loads. 3. 3D finite element model (SAP2000, Ver.16). 4. Design of vertical elements (CSI, Ver.9).

TABLE OF CONTANINET 1. Design criteria. 2. Lateral loads. 3. 3D finite element model (SAP2000, Ver.16). 4. Design of vertical elements (CSI, Ver.9). TABLE OF CONTANINET 1. Design criteria. 2. Lateral loads. 2-1. Wind loads calculation 2-2. Seismic loads 3. 3D finite element model (SAP2000, Ver.16). 4. Design of vertical elements (CSI, Ver.9). 4-1.

More information

DIVISION: METALS SECTION: METAL FASTENINGS SECTION: STEEL DECKING REPORT HOLDER: PNEUTEK, INC.

DIVISION: METALS SECTION: METAL FASTENINGS SECTION: STEEL DECKING REPORT HOLDER: PNEUTEK, INC. ICC ES Report ICC ES () 7 () www.icc es.org Most Widely Accepted and Trusted ESR 1 Reissued /1 This report is subject to renewal /. DIVISION: METALS SECTION: METAL FASTENINGS SECTION: 1 STEEL ING REPORT

More information

4.3 Moment Magnification

4.3 Moment Magnification CHAPTER 4: Reinforced Concrete Columns 4.3 Moment Magnification Description An ordinary or first order frame analysis does not include either the effects of the lateral sidesway deflections of the column

More information

DEFLECTION CALCULATIONS (from Nilson and Nawy)

DEFLECTION CALCULATIONS (from Nilson and Nawy) DEFLECTION CALCULATIONS (from Nilson and Nawy) The deflection of a uniformly loaded flat plate, flat slab, or two-way slab supported by beams on column lines can be calculated by an equivalent method that

More information

Design of AAC wall panel according to EN 12602

Design of AAC wall panel according to EN 12602 Design of wall panel according to EN 160 Example 3: Wall panel with wind load 1.1 Issue Design of a wall panel at an industrial building Materials with a compressive strength 3,5, density class 500, welded

More information

Design of Reinforced Concrete Beam for Shear

Design of Reinforced Concrete Beam for Shear Lecture 06 Design of Reinforced Concrete Beam for Shear By: Prof Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk 1 Topics Addressed Shear Stresses in Rectangular

More information

Roadway Grade = m, amsl HWM = Roadway grade dictates elevation of superstructure and not minimum free board requirement.

Roadway Grade = m, amsl HWM = Roadway grade dictates elevation of superstructure and not minimum free board requirement. Example on Design of Slab Bridge Design Data and Specifications Chapter 5 SUPERSTRUCTURES Superstructure consists of 10m slab, 36m box girder and 10m T-girder all simply supported. Only the design of Slab

More information

3.4 Analysis for lateral loads

3.4 Analysis for lateral loads 3.4 Analysis for lateral loads 3.4.1 Braced frames In this section, simple hand methods for the analysis of statically determinate or certain low-redundant braced structures is reviewed. Member Force Analysis

More information

3.2 Reinforced Concrete Slabs Slabs are divided into suspended slabs. Suspended slabs may be divided into two groups:

3.2 Reinforced Concrete Slabs Slabs are divided into suspended slabs. Suspended slabs may be divided into two groups: Sabah Shawkat Cabinet of Structural Engineering 017 3. Reinforced Concrete Slabs Slabs are divided into suspended slabs. Suspended slabs may be divided into two groups: (1) slabs supported on edges of

More information

Design of Reinforced Concrete Beam for Shear

Design of Reinforced Concrete Beam for Shear Lecture 06 Design of Reinforced Concrete Beam for Shear By: Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk Topics Addressed Shear Stresses in Rectangular Beams Diagonal Tension

More information

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich UNIVERSITY OF SASKATCHEWAN ME 313.3 MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS For Marker s Use Only LAST NAME (printed): FIRST

More information

AISC LRFD Beam Design in the RAM Structural System

AISC LRFD Beam Design in the RAM Structural System Model: Verification11_3 Typical Floor Beam #10 W21x44 (10,3,10) AISC 360-05 LRFD Beam Design in the RAM Structural System Floor Loads: Slab Self-weight: Concrete above flute + concrete in flute + metal

More information

SIMPLIFIED DESIGN OF REINFORCED CONCRETE SLABS AND BEAMS

SIMPLIFIED DESIGN OF REINFORCED CONCRETE SLABS AND BEAMS SIMPLIFIED DESIGN OF REINFORCED CONCRETE SLABS AND BEAMS MD. MAHMUDUN NOBE NASIMA SULTANA A.F.M. ASHIK RAHMAN DEPARTMENT OF CIVIL ENGINEERING AHSANULLAH UNIVERSITY OF SCIENCE AND TECHNLOLOGY JUNE 2016

More information

Lecture-03 Design of Reinforced Concrete Members for Flexure and Axial Loads

Lecture-03 Design of Reinforced Concrete Members for Flexure and Axial Loads Lecture-03 Design of Reinforced Concrete Members for Flexure and Axial Loads By: Prof. Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk www.drqaisarali.com Prof.

More information

Suspended high-rise. Suspended high-rise Copyright G G Schierle, press Esc to end, for next, for previous slide 1

Suspended high-rise. Suspended high-rise Copyright G G Schierle, press Esc to end, for next, for previous slide 1 Suspended high-rise Suspended high-rise Copyright G G Schierle, 2001-06 press Esc to end, for next, for previous slide 1 Suspended high-rise 1 Gravity load path 2 Differential deflection 3 Prestress to

More information

Job No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet. Member Design - Steel Composite Beam XX 22/09/2016

Job No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet. Member Design - Steel Composite Beam XX 22/09/2016 CONSULTING Engineering Calculation Sheet jxxx 1 Member Design - Steel Composite Beam XX Introduction Chd. 1 Grade 50 more common than Grade 43 because composite beam stiffness often 3 to 4 times non composite

More information

Job No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet. Member Design - RC Two Way Spanning Slab XX

Job No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet. Member Design - RC Two Way Spanning Slab XX CONSULTING Engineering Calculation Sheet E N G I N E E R S Consulting Engineers jxxx 1 Material Properties Characteristic strength of concrete, f cu ( 60N/mm 2 ; HSC N/A) 35 N/mm 2 OK Yield strength of

More information

FRAME ANALYSIS. Dr. Izni Syahrizal bin Ibrahim. Faculty of Civil Engineering Universiti Teknologi Malaysia

FRAME ANALYSIS. Dr. Izni Syahrizal bin Ibrahim. Faculty of Civil Engineering Universiti Teknologi Malaysia FRAME ANALYSIS Dr. Izni Syahrizal bin Ibrahim Faculty of Civil Engineering Universiti Teknologi Malaysia Email: iznisyahrizal@utm.my Introduction 3D Frame: Beam, Column & Slab 2D Frame Analysis Building

More information

Delhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web: Ph:

Delhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web:     Ph: Serial : IG1_CE_G_Concrete Structures_100818 Delhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web: E-mail: info@madeeasy.in Ph: 011-451461 CLASS TEST 018-19 CIVIL ENGINEERING

More information

CHAPTER 5. T a = 0.03 (180) 0.75 = 1.47 sec 5.12 Steel moment frame. h n = = 260 ft. T a = (260) 0.80 = 2.39 sec. Question No.

CHAPTER 5. T a = 0.03 (180) 0.75 = 1.47 sec 5.12 Steel moment frame. h n = = 260 ft. T a = (260) 0.80 = 2.39 sec. Question No. CHAPTER 5 Question Brief Explanation No. 5.1 From Fig. IBC 1613.5(3) and (4) enlarged region 1 (ASCE 7 Fig. -3 and -4) S S = 1.5g, and S 1 = 0.6g. The g term is already factored in the equations, thus

More information

Design Beam Flexural Reinforcement

Design Beam Flexural Reinforcement COPUTERS AND STRUCTURES, INC., BERKELEY, CALIFORNIA DECEBER 2001 CONCRETE FRAE DESIGN ACI-318-99 Technical Note This Technical Note describes how this program completes beam design when the ACI 318-99

More information

Therefore, for all members designed according to ACI 318 Code, f s =f y at failure, and the nominal strength is given by:

Therefore, for all members designed according to ACI 318 Code, f s =f y at failure, and the nominal strength is given by: 5.11. Under-reinforced Beams (Read Sect. 3.4b oour text) We want the reinforced concrete beams to fail in tension because is not a sudden failure. Therefore, following Figure 5.3, you have to make sure

More information

Entrance exam Master Course

Entrance exam Master Course - 1 - Guidelines for completion of test: On each page, fill in your name and your application code Each question has four answers while only one answer is correct. o Marked correct answer means 4 points

More information

Steel Cross Sections. Structural Steel Design

Steel Cross Sections. Structural Steel Design Steel Cross Sections Structural Steel Design PROPERTIES OF SECTIONS Perhaps the most important properties of a beam are the depth and shape of its cross section. There are many to choose from, and there

More information

REINFORCED CONCRETE DESIGN 1. Design of Column (Examples and Tutorials)

REINFORCED CONCRETE DESIGN 1. Design of Column (Examples and Tutorials) For updated version, please click on http://ocw.ump.edu.my REINFORCED CONCRETE DESIGN 1 Design of Column (Examples and Tutorials) by Dr. Sharifah Maszura Syed Mohsin Faculty of Civil Engineering and Earth

More information

STRUCTURAL ANALYSIS CHAPTER 2. Introduction

STRUCTURAL ANALYSIS CHAPTER 2. Introduction CHAPTER 2 STRUCTURAL ANALYSIS Introduction The primary purpose of structural analysis is to establish the distribution of internal forces and moments over the whole part of a structure and to identify

More information

Introduction...COMB-2 Design Considerations and Examples...COMB-3

Introduction...COMB-2 Design Considerations and Examples...COMB-3 SECTION DIRECTORY General Information Introduction...COMB-2 Design Considerations and Examples...COMB-3 Combination Assembly Recommendations and Limitations Composite Configurations...COMB-4 Typical Sealant

More information

a 1 ft2 144 in 2 b 26 in.

a 1 ft2 144 in 2 b 26 in. 1 1. The floor of a heavy storage warehouse building is made of 6-in.-thick stone concrete. If the floor is a slab having a length of 15 ft and width of 10 ft, determine the resultant force caused by the

More information

Preferred practice on semi-integral abutment layout falls in the following order:

Preferred practice on semi-integral abutment layout falls in the following order: GENERAL INFORMATION: This section of the chapter establishes the practices and requirements necessary for the design and detailing of semi-integral abutments. For general requirements and guidelines on

More information

This Technical Note describes how the program checks column capacity or designs reinforced concrete columns when the ACI code is selected.

This Technical Note describes how the program checks column capacity or designs reinforced concrete columns when the ACI code is selected. COMPUTERS AND STRUCTURES, INC., BERKELEY, CALIFORNIA DECEMBER 2001 CONCRETE FRAME DESIGN ACI-318-99 Technical Note This Technical Note describes how the program checks column capacity or designs reinforced

More information

3.5 Reinforced Concrete Section Properties

3.5 Reinforced Concrete Section Properties CHAPER 3: Reinforced Concrete Slabs and Beams 3.5 Reinforced Concrete Section Properties Description his application calculates gross section moment of inertia neglecting reinforcement, moment of inertia

More information

Rigid and Braced Frames

Rigid and Braced Frames RH 331 Note Set 12.1 F2014abn Rigid and raced Frames Notation: E = modulus of elasticit or Young s modulus F = force component in the direction F = force component in the direction FD = free bod diagram

More information

Chapter 4 Seismic Design Requirements for Building Structures

Chapter 4 Seismic Design Requirements for Building Structures Chapter 4 Seismic Design Requirements for Building Structures where: F a = 1.0 for rock sites which may be assumed if there is 10 feet of soil between the rock surface and the bottom of spread footings

More information

PEER/SSC Tall Building Design. Case study #2

PEER/SSC Tall Building Design. Case study #2 PEER/SSC Tall Building Design Case study #2 Typical Plan View at Ground Floor and Below Typical Plan View at 2 nd Floor and Above Code Design Code Design Shear Wall properties Shear wall thickness and

More information

Structural Steelwork Eurocodes Development of A Trans-national Approach

Structural Steelwork Eurocodes Development of A Trans-national Approach Structural Steelwork Eurocodes Development of A Trans-national Approach Course: Eurocode Module 7 : Worked Examples Lecture 0 : Simple braced frame Contents: 1. Simple Braced Frame 1.1 Characteristic Loads

More information

CHAPTER 4: BENDING OF BEAMS

CHAPTER 4: BENDING OF BEAMS (74) CHAPTER 4: BENDING OF BEAMS This chapter will be devoted to the analysis of prismatic members subjected to equal and opposite couples M and M' acting in the same longitudinal plane. Such members are

More information

10012 Creviston DR NW Gig Harbor, WA fax

10012 Creviston DR NW Gig Harbor, WA fax C.R. Laurence Co., Inc. ATTN: Chris Hanstad 2503 East Vernon Los Angeles, CA 90058 27 March 2013 SUBJ: CRL SRS STANDOFF RAILING SYSTEM GLASS BALUSTRADE GUARDS The SRS Standoff Railing System is an engineered

More information

Where and are the factored end moments of the column and >.

Where and are the factored end moments of the column and >. 11 LIMITATION OF THE SLENDERNESS RATIO----( ) 1-Nonsway (braced) frames: The ACI Code, Section 6.2.5 recommends the following limitations between short and long columns in braced (nonsway) frames: 1. The

More information

ORIGIN 0. PTC_CE_BSD_7.2_us_mp.mcdx. Mathcad Enabled Content Copyright 2011 Knovel Corp.

ORIGIN 0. PTC_CE_BSD_7.2_us_mp.mcdx. Mathcad Enabled Content Copyright 2011 Knovel Corp. PC_CE_BSD_7._us_mp.mcdx Copyright 011 Knovel Corp. Building Structural Design homas P. Magner, P.E. 011 Parametric echnology Corp. Chapter 7: Reinforced Concrete Column and Wall Footings 7. Pile Footings

More information

CE5510 Advanced Structural Concrete Design - Design & Detailing of Openings in RC Flexural Members-

CE5510 Advanced Structural Concrete Design - Design & Detailing of Openings in RC Flexural Members- CE5510 Advanced Structural Concrete Design - Design & Detailing Openings in RC Flexural Members- Assoc Pr Tan Kiang Hwee Department Civil Engineering National In this lecture DEPARTMENT OF CIVIL ENGINEERING

More information

DESIGN AND DETAILING OF COUNTERFORT RETAINING WALL

DESIGN AND DETAILING OF COUNTERFORT RETAINING WALL DESIGN AND DETAILING OF COUNTERFORT RETAINING WALL When the height of the retaining wall exceeds about 6 m, the thickness of the stem and heel slab works out to be sufficiently large and the design becomes

More information

Karbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi

Karbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi Chapter 05 Structural Steel Design According to the AISC Manual 13 th Edition Analysis and Design of Beams By Dr. Jawad Talib Al-Nasrawi University of Karbala Department of Civil Engineering 71 Introduction

More information

ENERGY DIAGRAM w/ HYSTERETIC

ENERGY DIAGRAM w/ HYSTERETIC ENERGY DIAGRAM ENERGY DIAGRAM w/ HYSTERETIC IMPLIED NONLINEAR BEHAVIOR STEEL STRESS STRAIN RELATIONSHIPS INELASTIC WORK DONE HYSTERETIC BEHAVIOR MOMENT ROTATION RELATIONSHIP IDEALIZED MOMENT ROTATION DUCTILITY

More information

Failure in Flexure. Introduction to Steel Design, Tensile Steel Members Modes of Failure & Effective Areas

Failure in Flexure. Introduction to Steel Design, Tensile Steel Members Modes of Failure & Effective Areas Introduction to Steel Design, Tensile Steel Members Modes of Failure & Effective Areas MORGAN STATE UNIVERSITY SCHOOL OF ARCHITECTURE AND PLANNING LECTURE VIII Dr. Jason E. Charalambides Failure in Flexure!

More information

Mechanics of Materials

Mechanics of Materials Mechanics of Materials Notation: a = acceleration = area (net = with holes, bearing = in contact, etc...) SD = allowable stress design d = diameter of a hole = calculus symbol for differentiation e = change

More information

DESIGN REINFORCED CEMENT CONCRETE STRUCTURAL MEMBERS

DESIGN REINFORCED CEMENT CONCRETE STRUCTURAL MEMBERS DESIGN OF REINFORCED CEMENT CONCRETE STRUCTURAL MEMBERS Contents CHAPTER 1.0 General: 1.1 Symbols 1. Materials 1..1 Cement 1.. Aggregate 1..3 Water 1..4 Admixtures 1..5 Reinforcement CHAPTER.0 Concrete:.1

More information

Purpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on Exam 3.

Purpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on Exam 3. ES230 STRENGTH OF MTERILS Exam 3 Study Guide Exam 3: Wednesday, March 8 th in-class Updated 3/3/17 Purpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on

More information

This procedure covers the determination of the moment of inertia about the neutral axis.

This procedure covers the determination of the moment of inertia about the neutral axis. 327 Sample Problems Problem 16.1 The moment of inertia about the neutral axis for the T-beam shown is most nearly (A) 36 in 4 (C) 236 in 4 (B) 136 in 4 (D) 736 in 4 This procedure covers the determination

More information

FLOW CHART FOR DESIGN OF BEAMS

FLOW CHART FOR DESIGN OF BEAMS FLOW CHART FOR DESIGN OF BEAMS Write Known Data Estimate self-weight of the member. a. The self-weight may be taken as 10 percent of the applied dead UDL or dead point load distributed over all the length.

More information

Practical Design to Eurocode 2

Practical Design to Eurocode 2 Practical Design to Eurocode 2 The webinar will start at 12.30 (Any questions beforehand? use Questions on the GoTo Control Panel) Course Outline Lecture Date Speaker Title 1 21 Sep Jenny Burridge Introduction,

More information

Supplement: Statically Indeterminate Trusses and Frames

Supplement: Statically Indeterminate Trusses and Frames : Statically Indeterminate Trusses and Frames Approximate Analysis - In this supplement, we consider an approximate method of solving statically indeterminate trusses and frames subjected to lateral loads

More information

Beam Bending Stresses and Shear Stress

Beam Bending Stresses and Shear Stress Beam Bending Stresses and Shear Stress Notation: A = name or area Aweb = area o the web o a wide lange section b = width o a rectangle = total width o material at a horizontal section c = largest distance

More information

Properties of Sections

Properties of Sections ARCH 314 Structures I Test Primer Questions Dr.-Ing. Peter von Buelow Properties of Sections 1. Select all that apply to the characteristics of the Center of Gravity: A) 1. The point about which the body

More information

Chapter 8: Bending and Shear Stresses in Beams

Chapter 8: Bending and Shear Stresses in Beams Chapter 8: Bending and Shear Stresses in Beams Introduction One of the earliest studies concerned with the strength and deflection of beams was conducted by Galileo Galilei. Galileo was the first to discuss

More information

Design of Beams (Unit - 8)

Design of Beams (Unit - 8) Design of Beams (Unit - 8) Contents Introduction Beam types Lateral stability of beams Factors affecting lateral stability Behaviour of simple and built - up beams in bending (Without vertical stiffeners)

More information

PROPOSED SATSANG HALL TECHNICAL REPORT

PROPOSED SATSANG HALL TECHNICAL REPORT PROPOSED SATSANG HALL - VERTICAL STRIP V1 1 ------------------------------------------------------------------------------ ADAPT CORPORATION STRUCTURAL CONCRETE SOFTWARE SYSTEM 1733 Woodside Road, Suite

More information

Chapter 9: Column Analysis and Design

Chapter 9: Column Analysis and Design Chapter 9: Column Analysis and Design Introduction Columns are usually considered as vertical structural elements, but they can be positioned in any orientation (e.g. diagonal and horizontal compression

More information

A Simply supported beam with a concentrated load at mid-span: Loading Stages

A Simply supported beam with a concentrated load at mid-span: Loading Stages A Simply supported beam with a concentrated load at mid-span: Loading Stages P L/2 L PL/4 MOMNT F b < 1 lastic F b = 2 lastic F b = 3 lastoplastic 4 F b = Plastic hinge Plastic Dr. M.. Haque, P.. (LRFD:

More information

Explanatory Examples for Ductile Detailing of RC Buildings

Explanatory Examples for Ductile Detailing of RC Buildings Document No. :: IITK-GSD-EQ-V3.0 Final Report :: - Earthquake Codes IITK-GSD Project on Building Codes Explanatory Examples or Ductile Detailing o RC Buildings by Dr. R. K. Ingle Department o pplied echanics

More information