Comparative investigation of permanent magnet linear oscillatory actuators used in orbital friction vibration machine

Size: px
Start display at page:

Download "Comparative investigation of permanent magnet linear oscillatory actuators used in orbital friction vibration machine"

Transcription

1 International Journal of Applied Electromagnetics and Mechanics 45 (214) DOI /JAE IOS Press Comparative investigation of permanent magnet linear oscillatory actuators used in orbital friction vibration machine Fei Xu, Jianhui Hu, Jibin Zou, Yong Li, Yongxiang Xu and Hua Fan Department of Electrical Engineering, Harbin Institute of Technology, Harbin, Heilongjiang, China Abstract. The paper describes the alternative designs and performances of a single-phase moving-magnet linear oscillating actuator (LOA) which has been developed for orbital friction welding. The influences of the pole ratio on the performance of the LOAs are investigated and the optimal parameters have been identified with reference to the thrust force characteristics. It can be illustrated that a quasi-halbach magnetized LOA, in which the magnets are assembled on a nonmagnetic mover yoke, represents the best electromagnetic performances. Finally, the predicted thrust force-current characteristic of quasi-halbach magnetized LOA is validated by measurements on a prototype actuator. Keywords: Orbital friction vibration welding, linear oscillatory actuator, thrust force, optimal design 1. Introduction Orbital Friction Vibration Actuator (OFVA) is a core component of Orbital Friction Welding Machine (OFWM), which is a novel apertureless welding driving device. It can produce a force upon the still mover which then vibrates according to the predetermined orbital [1 4]. This paper proposes a highthrust force permanent magnet (PM) machine used to weld metals which employs rare earth magnet to generate magnetic field. It has some advantages, such as great transferring energy, high efficiency and high thrust force density. The displacements are decoupled with air gap as it moves in the xy plane. The reluctance cogging force is small and it shows a slight inverted pendulum effect. As can be seen in Fig. 1, PM OFVA is composed of four identical linear PM actuators and spring. There are two distributed in x and y directions which can control the motion in x and y directions respectively. Due to the decoupled relationship between the amplitudes in x and y directions, only one linear oscillating actuator (LOAs) in one direction should be analyzed. PM LOAs have aroused extensive study interests recently, due to their high efficiency and high power density, and have fell into a wide range of industries, such as artificial heart, compressors, pumps, vibrators, robots etc. [5 8]. [5,7] has reported on tubular moving-magnet topologies with C-cored stator back iron. [9] has studied comparative design of C-cored and E-cored single-phase tubular moving-magnet LOAs and has summed up that the feasible combinations of stator tooth number N t and the mover pole Corresponding author: Jianhui Hu, Department of Electrical Engineering, Harbin Institute of Technology, Harbin, Heilongjiang, China. Tel.: ; hujianhui@hit.edu.cn /14/$27.5 c 214 IOS Press and the authors. All rights reserved

2 582 F. Xu et al. / Comparative investigation of permanent magnet linear oscillatory actuators (a) (b) C2 (c) C3 (d) (e) Fig. 1. Schematic of PM orbital friction welding actuator. Fig. 2. Schematics of unit C-cored PM LOAs. number N p were ruled by N t N p =1. A 2-pole, E-core tubular LOA equipped with quasi-halbach surface-mounted permanent magnets (HSPM) was investigated and some important performances had been predicted and validated by measurements. A linear single phase permanent magnet oscillating motor used in domestic refrigerator had been designed and tested and mainly investigated optimizing cost and efficiency [1]. By considering the references above and according the feature of short stroke which friction welding requires, the paper proposes a type of single-phase permanent magnetic linear LOA. Alternative design concepts for single-phase PM linear LOAs are reviewed. The performances of LOA equipped with radially, tangentially and quasi-halbach magnetized movers, and C-cored stator, are then predicted by finite element analysis. The predicted thrust force-current characteristic of the quasi-halbach magnetized LOA is validated by measurements. 2. Magnetized topologies and analysis of unit C-cored LOAs Figure 2 shows the schematics and the on-load flux distributions of five linear PM LOAs equipped with C-cored stator cores. The movers differ from each other in terms of pole number and magnetization. As is shown in Fig. 2(a), which has one radially magnetized magnet sandwiched between two axially magnetized magnets is simple to manufacture. The mover in Fig. 2(b) has three radially magnetized magnets of alternate polarity which can yield a three-pole magnet field. An actuator has one radially magnetized magnet which is sandwiched between two iron blocks and its mover employs a nonmagnetic yoke, as shown in Fig. 2(c), and also a three-pole magnetic field can be yielded., as shown in Fig. 2(d), is originally proposed in [5]. This topology is easier to manufacture, because it has two tangentially magnetized magnets sandwiched between three iron blocks. The mover yoke is made of nonmagnetic material. Considering the magnetizing technique and cost, a quasi-halbach magnetized mover can be obtained commonly by employing assembling method. A quasi-halbach array commonly consists of 3 to 5 magnets which have different magnetized directions. A good sinusoidal property can be acquired by increasing the number of each magnetic pole. However, the magnetizing technique will be complicated. The mover in Fig. 2(e) employs three magnets which contain one radially magnetized and two axially magnetized magnets to comprise a quasi-halbach array. The flux which passes through the mover yoke of is much, however, the flux which remains in the mover of yoke is so little. Therefore, can employ

3 F. Xu et al. / Comparative investigation of permanent magnet linear oscillatory actuators 583 Table 1 Design Parameters Items Symbol Units Value Stroke range x mm ± 1 Air-gap length g mm 2 Magnet length in the magnetized direction h m mm 1 Remanence of magnets (N38SH) B r T 1.23 Length of stator core L ef mm 5 Winding turns N 1 Current density J A/mm C2 C Fig. 3. Variations of thrust force produced by, C2 and C3 with α p (I = 2.8 A) τp3 =.9 =.13 =.16 =.19 =.22 Fig. 4. Variations of thrust force with τ p3 under different α p (I = 2.8 A). a nonmagnetic mover yoke. The topology can enhance the air-gap flux density and provide the main flux return path, and also has a good thrust force capability. These models are unit actuators, because they are set to be periodical in FE predictons, and therefore, it is unnecessary to consider air-gap fringe effect. 3. Optimization of unit C-cored LOAs The preliminary design principles are to maximize thrust force per unit area of the proposed unit actuator, i.e., small volume of the actuator should be kept to maximize the thrust force per unit area under the premise of satisfying the prescribed thrust force. The pole ratio α p = τ p1 /τ p (Fig. 2) has a great impact on the thrust force-displacement characteristic. Therefore, α p will be optimized to maximize thrust force per unit area. Various moving-magnet LOAs with C-cored stator are investigated and the design parameters are listed in Table Radial magnetized topology Figure 3 shows the variations of the thrust forces produced by, C2 and C3 with α p. As will be seen, the optimal α p of and C2 are identical, 1 and at this time, the thrust force is maximal. As α p is smaller than 1, the thrust force produced by is larger than that of C2 because C2 suffers from significant leakage flux between magnets; As α p exceeds.47, the thrust force will not increase noticeably, since the magnets consume most of their permanent magnetic motive force on the internal magnetic resistance; As α p decreases below.16, the reverse effect of the magnet field is

4 584 F. Xu et al. / Comparative investigation of permanent magnet linear oscillatory actuators nonmagnetic ferromagnetic Fig. 5. Variations of thrust force with α p when mover employs ferromagnetic and nonmagnetic mover yoke (I = 2.8 A). 12 nonmagnetic ferromagnetic 8 Fig. 6. Variations of thrust force with α p when mover employs ferromagnetic and nonmagnetic mover yokes (I = 2.8 A). enhanced and therefore a negative thrust force is produced. C3 fails to take full advantage of the space and suffers from large flux leakage which makes it difficult to enhance its thrust force. Thrust forces produced by the three topologies with ferromagnetic mover yoke are larger than those with nonmagnetic mover yoke. Therefore, there is no need to discuss the topologies with nonmagnetic mover yoke Tangential magnetized topology τ p3 (τ p3 =2τ p2 )andα p are optimized simultaneously and Fig. 4 shows the variations of thrust force with τ p3.asτ p3 is 27 mm and α p is.16, the actuator with a nonmagnetic mover yoke can generate the maximal thrust force, 189 N. The optimal axially magnetized configuration is one iron block sandwiched between two axially magnetized magnets without iron block on the either side of the model. The variations of thrust force with τ p3 as it employs a ferromagnetic and nonmagnetic mover yoke, Fig. 5. The thrust force produced by the LOA which employs a nonmagnetic mover yoke is noticeably greater than that employs a nonmagnetic mover yoke. However, the saturation level in the middle iron block is relatively high, and therefore the air-gap flux density cannot be further improved and then the thrust force will be limited, and more eddy current loss will be generated Quasi-Halbach magnetized topology Figure 6 shows the variations of thrust force produced by with α p when it employs a ferromagnetic and nonmagnetic mover yoke. As will be seen, the maximal thrust force (182 N) will occur when α p is.19 for possessing a nonmagnetic mover yoke. Therefore, a nonmagnetic mover yoke can be selected for reducing the mover weight and enhancing the dynamic response of the system. 4. Comparison of characteristics of unit C-cored LOA 4.1. Comparison of the thrust force, excitation force and cogging force Figure 7 shows the variations of thrust forces with α p of,,. As can be seen, α p corresponding to the maximal thrust force of the three magnetized configuration are various. can obtain the largest

5 F. Xu et al. / Comparative investigation of permanent magnet linear oscillatory actuators Fig. 7. Variations of thrust force of three magnetized topologies with α p (I = 2.8 A). Thrust force (N) Position (mm) Fig. 8. Variations of thrust force with position (I = 2.8 A). Excitation force (N) Position (mm) Fig. 9. Variations of excitation force with position (I = 2.8 A). Cogging force (N) Position (mm) Fig. 1. Variations of cogging force with position. thrust force and the maximal thrust force produced by is 3.7% lower than that produce by. The excitation force, produced by the interaction of PMs and current and the only force component contributing to the power output, is obtained by minus the cogging and reluctance forces from the thrust force. Figures 8 1 show the variations of thrust, excitation and cogging force with position. As will be seen in Figs 8 and 9, the thrust force and excitation force produced by are larger than the other topologies. The variations of thrust force produced by and are 5.9% and 5.3% respectively and those of excitation force are 3.5% and 2.3% over the stroke range. Obviously, although can produce larger thrust force and excitation force, it presents larger thrust force fluctuation correspondingly over the stroke range. The curve of excitation force of has a better flatness than the other ones. As can be seen in Fig. 1, the cogging force produced by is larger than the others over the stroke range and the cogging force of is the smallest Comparison of nonlinearity of thrust force-current characteristic Figure 11 shows the characteristics of thrust force-current which, and possess. As can be seen, the thrust force-current characteristic curves appear various tendencies as the ampereturns of the coils exceed 25 A. Among them, the linearity of the thrust force-current characteristic of

6 586 F. Xu et al. / Comparative investigation of permanent magnet linear oscillatory actuators Table 2 Average flux densities along A, B and C lines Stator position A line T T 1.41 T B line T T T C line T T 1.29 T Thrust force (N) Ampere-turn (A) Fig. 11. Characteristics of thrust force-current. is superior to the other topologies, which illustrates that the quasi-halbach magnetized topology has a better overload performance Comparison of stator iron loss The influence of stator iron loss on the operational efficiency shouldn t be neglected and the distribution states of flux density in the stator tooth can reflect indirectly the state of the stator iron loss, therefore, the variations of the average flux densities along A, B, and C lines in the stator teeth of, and with α p are investigated, as evident in Fig. 12. As can be seen, α p has little impact on the average flux densities along A and B lines and the stator core around the both lines are not saturated. The average flux densities along A and B lines of decrease slightly with increasing α p andtendtobeno saturated, and that along C line increases gradually with increasing α p. The average tooth flux densities along the three lines of decrease gradually with increasing α p and those are obviously larger than the two other topologies when α p is small, and also the saturation level of the stator region which B line locates is the most severe. The average tooth flux densities along the A and B lines of both appear first dropping and then ascending slowly, and that along C line first increases and then decreases with increasing α p. The average flux densities along C lines of all the topologies are far from saturation. The average flux densities along A, B and C lines as the three topologies obtain their respective maximal thrust force are shown in Table 2. As will be seen, the average flux densities of are smaller than the others along the three lines. Overall, can not only produce a great thrust force, but possesses very small flux densities in the stator teeth. Therefore, the stator iron loss generated by is also smaller and its efficiency will be higher than the other topologies. 5. Thrust force per unit area Thrust force per unit area, F σ, is one of the most significant criteria to evaluate the performance of LOA. Great thrust force per unit area indicates smaller volume of LOA can produce a larger thrust force and a higher utilization of permanent magnets. The formula of thrust force per unit area is defined by Eq. (1). F σ = F avg τ p L ef (1)

7 F. Xu et al. / Comparative investigation of permanent magnet linear oscillatory actuators 587 A Line (T) B Line (T) C Line (T) A B C Thrust Force Per Unit Area (N/mm 2 ) 1.18 x τp (mm) Fig. 12. Comparison of variations of average tooth flux densities with α p along stator tooth lines. Fig. 13. Variations of thrust force per unit area with τ p (I = 2.8 A). Spring Stator top cap Stator Winding Thrust force (N) FE Measured Magnet Mover yoke Ampere-turn (A) Fig. 14. Prototype LOA. Fig. 15. Thrust force-current characteristics. Where F avg is the average thrust force over the stroke range, L ef is the stator core length. Figure 13 shows the variations of thrust force per unit area produced by and whose stator core lengths L ef are identical, 5 mm with τ p.asτ p of is 1, the maximal thrust force density of can reach 1127 N/mm 2 and can obtains its maximal thrust force density, N/mm 2.Aswillbe seen, the discrepancy between them is not considerable. 6. Prototyping and experiment A prototype of has been manufactured so as to experimentally validate the foregoing analyses (Fig. 14). However, for the consideration of practical application, the prototype employed four topologies combined together to yield a larger thrust force. Some of flux leakage will be brought about on either side of the actuator. Therefore, the practical thrust force will correspondingly be less than four

8 588 F. Xu et al. / Comparative investigation of permanent magnet linear oscillatory actuators times as much as the maximal thrust force of. The predicted thrust force-current is compared with measurement (Fig. 15), and a good agreement is achieved. 7. Conclusions This paper aims at introducing a new design method to maximize the thrust force per unit area and decrease the thrust force fluctuation of single-phase PM LOA. The radial, tangential and quasi-halbach magnetized topologies and performances are analyzed. The influences of the pole ratio α p on the performance of the LOAs are investigated and the optimal parameters have been identified to maximize the thrust force per unit area. It can be concluded that a quasi-halbach magnetized LOA with a nonmagnetic mover yoke, represents a large thrust force, a good linearity of thrust force-current characteristic and low stator iron loss. Finally, the predicted thrust force-current characteristic of quasi-halbach magnetized LOA is validated by measurements on a prototype actuator and a good agreement between them has been achieved. Acknowledgment This work was supported by the National Key Basic Research Program of China (973 Program) under Grant 213CB3565. References [1] M.J. Troughton, Handbook of plastic joining: A practical guide 2nd edition, William Andrew Inc, Georgia, 8, pp [2] F. Xu, J. Hu, Y. Li, J. Zou, Y. Xu and J. Shang, System modeling and operational characteristic analysis for an orbital friction vibration actuator used in orbital vibration welding, AECE 13(2) (213), [3] D.A. Grewell and A. Benatar, Comparsion of orbital and linear vibration welding of thermoplastics, Polymer Engineering and Science 49(7) (9), [5] Dicnamesta 44(3), [4] Y. Li, Z. Nie, Y. Lu and Z. Guo, Structure and working principle of orbital electromagnetic vibrating head, Small and Special Electrical Machines 35(11) (7), 8 1. [5] M. Watada et al., Improvement on characteristics of linear oscillatory actuator for artificial hearts, IEEE Trans Magn 29(6) (1993), [6] I. Boldea and S.A. Nasar, Linear electric actuators and generators, IEEE Trans on Energy Conversion 14(3) (Sep 1999), [7] K.B. Park, E.P. Hong and H.K. Lee, Development of a linear motor for compressors of household refrigerators, Proc of 3rd Int, USA, (1995). [8] T. Mizuno, Y. Bu, M. Ohkubo, F. Tsuchiya and H. Yamada, Static thrust analysis of a moving magnet linear oscillatory actuator for vibration cancel system, Proc of 5th Int LDIA, Japan (5), [9] Z.Q. Zhu, X. Chen, D. Howe and S. Iwasaki, Electromag-netic modeling of a novel linear oscillating actuator, Proc of the 8 IEEE Int Magnetics Conf, Paper ID. CQ-1, Spain, 8. [1] Z.S. Al-Otaibi, Utilising SMC in single phase permanent magnet linear motors for compressor applications, 8.

Modeling and Design Optimization of Permanent Magnet Linear Synchronous Motor with Halbach Array

Modeling and Design Optimization of Permanent Magnet Linear Synchronous Motor with Halbach Array Modeling and Design Optimization of Permanent Magnet Linear Synchronous Motor with Halbach Array N. Roshandel Tavana, and A. Shoulaie nroshandel@ee.iust.ir, and shoulaie@ee.iust.ac.ir Department of Electrical

More information

Analysis of Half Halbach Array Configurations in Linear Permanent-Magnet Vernier Machine

Analysis of Half Halbach Array Configurations in Linear Permanent-Magnet Vernier Machine Journal of Magnetics 22(3), 414-422 (2017) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 https://doi.org/10.4283/jmag.2017.22.3.414 Analysis of Half Halbach Array Configurations in Linear Permanent-Magnet

More information

A New Moving-magnet Type Linear Actuator utilizing Flux Concentration Permanent Magnet Arrangement

A New Moving-magnet Type Linear Actuator utilizing Flux Concentration Permanent Magnet Arrangement 342 Journal of Electrical Engineering & Technology Vol. 7, No. 3, pp. 342~348, 2012 http://dx.doi.org/10.5370/jeet.2012.7.3.342 A New Moving-magnet Type Linear Actuator utilizing Flux Concentration Permanent

More information

Analysis and Experiments of the Linear Electrical Generator in Wave Energy Farm utilizing Resonance Power Buoy System

Analysis and Experiments of the Linear Electrical Generator in Wave Energy Farm utilizing Resonance Power Buoy System Journal of Magnetics 18(3), 250-254 (2013) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 http://dx.doi.org/10.4283/jmag.2013.18.3.250 Analysis and Experiments of the Linear Electrical Generator in Wave

More information

Development of a new linear actuator for Androids

Development of a new linear actuator for Androids 8 IEEE International Conference on Robotics and Automation Pasadena, CA, USA, May 19-3, 8 Development of a new linear actuator for Androids Masayuki MISHIMA, Hiroshi ISHIGURO and Katsuhiro HIRATA, Member,

More information

Doubly salient reluctance machine or, as it is also called, switched reluctance machine. [Pyrhönen et al 2008]

Doubly salient reluctance machine or, as it is also called, switched reluctance machine. [Pyrhönen et al 2008] Doubly salient reluctance machine or, as it is also called, switched reluctance machine [Pyrhönen et al 2008] Pros and contras of a switched reluctance machine Advantages Simple robust rotor with a small

More information

Experimental Tests and Efficiency Improvement of Surface Permanent Magnet Magnetic Gear

Experimental Tests and Efficiency Improvement of Surface Permanent Magnet Magnetic Gear IEEJ Journal of Industry Applications Vol.3 No.1 pp.62 67 DOI: 10.1541/ieejjia.3.62 Paper Experimental Tests and Efficiency Improvement of Surface Permanent Magnet Magnetic Gear Michinari Fukuoka a) Student

More information

This is a repository copy of Design optimization of radially magnetized, iron-cored, tubular permanent-magnet machines and drive systems.

This is a repository copy of Design optimization of radially magnetized, iron-cored, tubular permanent-magnet machines and drive systems. This is a repository copy of Design optimization of radially magnetized, iron-cored, tubular permanent-magnet machines and drive systems. White Rose Research Online URL for this paper: http://eprints.whiterose.ac.uk/825/

More information

Overload Capability of Linear Flux Switching Permanent Magnet Machines

Overload Capability of Linear Flux Switching Permanent Magnet Machines Applied Mechanics and Materials Vols. 416-417 (2013) pp 345-352 Online available since 2013/Sep/10 at www.scientific.net (2013) Trans Tech Publications, Switzerland doi:10.4028/www.scientific.net/amm.416-417.345

More information

This is a repository copy of Analysis and design optimization of an improved axially magnetized tubular permanent-magnet machine.

This is a repository copy of Analysis and design optimization of an improved axially magnetized tubular permanent-magnet machine. This is a repository copy of Analysis and design optimization of an improved axially magnetized tubular permanent-magnet machine. White Rose Research Online URL for this paper: http://eprints.whiterose.ac.uk/827/

More information

SHAPE DESIGN OPTIMIZATION OF INTERIOR PERMANENT MAGNET MOTOR FOR VIBRATION MITIGATION USING LEVEL SET METHOD

SHAPE DESIGN OPTIMIZATION OF INTERIOR PERMANENT MAGNET MOTOR FOR VIBRATION MITIGATION USING LEVEL SET METHOD International Journal of Automotive Technology, Vol. 17, No. 5, pp. 917 922 (2016) DOI 10.1007/s12239 016 0089 7 Copyright 2016 KSAE/ 092 17 pissn 1229 9138/ eissn 1976 3832 SHAPE DESIGN OPTIMIZATION OF

More information

Tubular Linear Permanent Magnet Actuator with Fractional Slots

Tubular Linear Permanent Magnet Actuator with Fractional Slots IEEJ Journal of Industry Applications Vol.1 No.3 pp.17 177 DOI: 10.1541/ieejjia.1.17 Paper Tubular Linear Permanent Magnet Actuator with Fractional Slots oberto Di Stefano Non-member, Fabrizio Marignetti

More information

1439. Numerical simulation of the magnetic field and electromagnetic vibration analysis of the AC permanent-magnet synchronous motor

1439. Numerical simulation of the magnetic field and electromagnetic vibration analysis of the AC permanent-magnet synchronous motor 1439. Numerical simulation of the magnetic field and electromagnetic vibration analysis of the AC permanent-magnet synchronous motor Bai-zhou Li 1, Yu Wang 2, Qi-chang Zhang 3 1, 2, 3 School of Mechanical

More information

Optimal Design of PM Axial Field Motor Based on PM Radial Field Motor Data

Optimal Design of PM Axial Field Motor Based on PM Radial Field Motor Data Optimal Design of PM Axial Field Motor Based on PM Radial Field Motor Data GOGA CVETKOVSKI LIDIJA PETKOVSKA Faculty of Electrical Engineering Ss. Cyril and Methodius University Karpos II b.b. P.O. Box

More information

Power density improvement of three phase flux reversal machine with distributed winding

Power density improvement of three phase flux reversal machine with distributed winding Published in IET Electric Power Applications Received on 4th January 2009 Revised on 2nd April 2009 ISSN 1751-8660 Power density improvement of three phase flux reversal machine with distributed winding

More information

Proposal of short armature core double-sided transverse flux type linear synchronous motor

Proposal of short armature core double-sided transverse flux type linear synchronous motor Proposal of short armature core double-sided transverse flux type linear synchronous motor Shin Jung-Seob a, Takafumi Koseki a and Kim Houng-Joong b a The University of Tokyo, Engineering Building #2 12F,7-3-1

More information

Optimization Design of a Segmented Halbach Permanent-Magnet Motor Using an Analytical Model

Optimization Design of a Segmented Halbach Permanent-Magnet Motor Using an Analytical Model IEEE TRANSACTIONS ON MAGNETICS, VOL. 45, NO. 7, JULY 2009 2955 Optimization Design of a Segmented Halbach Permanent-Magnet Motor Using an Analytical Model Miroslav Markovic Yves Perriard Integrated Actuators

More information

Experimental Assessment of Unbalanced Magnetic Force according to Rotor Eccentricity in Permanent Magnet Machine

Experimental Assessment of Unbalanced Magnetic Force according to Rotor Eccentricity in Permanent Magnet Machine Journal of Magnetics 23(1), 68-73 (218) ISSN (Print) 1226-175 ISSN (Online) 2233-6656 https://doi.org/1.4283/jmag.218.23.1.68 Experimental Assessment of Unbalanced Magnetic Force according to Rotor Eccentricity

More information

Hybrid Excited Vernier Machines with All Excitation Sources on the Stator for Electric Vehicles

Hybrid Excited Vernier Machines with All Excitation Sources on the Stator for Electric Vehicles Progress In Electromagnetics Research M, Vol. 6, 113 123, 16 Hybrid Excited Vernier Machines with All Excitation Sources on the Stator for Electric Vehicles Liang Xu, Guohai Liu, Wenxiang Zhao *, and Jinghua

More information

Accurate Joule Loss Estimation for Rotating Machines: An Engineering Approach

Accurate Joule Loss Estimation for Rotating Machines: An Engineering Approach Accurate Joule Loss Estimation for Rotating Machines: An Engineering Approach Adeeb Ahmed Department of Electrical and Computer Engineering North Carolina State University Raleigh, NC, USA aahmed4@ncsu.edu

More information

[2008] IEEE. Reprinted, with permission, from Lu, Haiwei; Zhu, Jianguo; Lin, Zhi Wei (Jack); Guo, Youguang. 2008, 'A miniature short stroke linear

[2008] IEEE. Reprinted, with permission, from Lu, Haiwei; Zhu, Jianguo; Lin, Zhi Wei (Jack); Guo, Youguang. 2008, 'A miniature short stroke linear [2008] IEEE. Reprinted, with permission, from Lu, Haiwei; Zhu, Jianguo; Lin, Zhi Wei (Jack); Guo, Youguang. 2008, 'A miniature short stroke linear actuator - Design and analysis', IEEE Transactions On

More information

ITEE Journal Information Technology & Electrical Engineering

ITEE Journal Information Technology & Electrical Engineering Comparative Study of Permanent Magnet Configurations of Short-Stroke Linear Motor for Reciprocating Compressor in Household Refrigerator Applications 1 Izzeldin IdrisAbdalla, 2 Taib Ibrahim, 3 Nursyarizal

More information

Magnetic Field and Oscillating Analysis of Hybrid Suspension Systems Combining Magnetic Spring and Damper

Magnetic Field and Oscillating Analysis of Hybrid Suspension Systems Combining Magnetic Spring and Damper APSAEM12 Jorunal of the Japan Society of Applied Electromagnetics and Mechanics Vol.21, No.3 (2013) Regular Paper Magnetic Field and Oscillating Analysis of Hybrid Suspension Systems Combining Magnetic

More information

Postprint. This is the accepted version of a paper presented at ACTUATOR 2014, Bremen, Germany, June 2014.

Postprint.   This is the accepted version of a paper presented at ACTUATOR 2014, Bremen, Germany, June 2014. http://www.diva-portal.org Postprint This is the accepted version of a paper presented at ACTUATOR 0, Bremen, Germany, 5 June 0. Citation for the original published paper: Chen, C., Bissal, A., Salinas,

More information

RELUCTANCE NETWORK MODEL OF A PERMANENT MAGNET TUBULAR MOTOR

RELUCTANCE NETWORK MODEL OF A PERMANENT MAGNET TUBULAR MOTOR Andrzej Waindok Bronisław Tomczuk DOI 0.55/ama-207-0029 RELUCTANCE NETWORK MODEL OF A PERMANENT MAGNET TUBULAR MOTOR Andrzej WAINDOK * Bronisław TOMCZUK * * Opole University of Technology Department of

More information

SCIENCE CHINA Technological Sciences. Nonlinear magnetic network models for flux-switching permanent magnet machines

SCIENCE CHINA Technological Sciences. Nonlinear magnetic network models for flux-switching permanent magnet machines SCIENCE CHINA Technological Sciences Article March 2016 Vol.59 No.3: 494 505 doi: 10.1007/s11431-015-5968-z Nonlinear magnetic network models for flux-switching permanent magnet machines ZHANG Gan, HUA

More information

Basics of Permanent Magnet - Machines

Basics of Permanent Magnet - Machines Basics of Permanent Magnet - Machines 1.1 Principles of energy conversion, force & torque 1.2 Basic design elements 1.3 Selection of PM-Machine topologies 1.4 Evaluation and Comparison Permanent Magnet

More information

A Linear Motor Driver with HTS Levitation Techniques

A Linear Motor Driver with HTS Levitation Techniques Volume 1, Number 1, June 2007 Journal of Science, Technology and Engineering 34 A Linear Motor Driver with HTS Levitation Techniques Jian-Xun Jin a, You-Guang Guo b, and Jian-Guo Zhu b a Centre of Applied

More information

Loss analysis of a 1 MW class HTS synchronous motor

Loss analysis of a 1 MW class HTS synchronous motor Journal of Physics: Conference Series Loss analysis of a 1 MW class HTS synchronous motor To cite this article: S K Baik et al 2009 J. Phys.: Conf. Ser. 153 012003 View the article online for updates and

More information

Operation of an Electromagnetic Trigger with a Short-circuit Ring

Operation of an Electromagnetic Trigger with a Short-circuit Ring Operation of an Electromagnetic Trigger with a Short-circuit Ring Dejan Križaj 1*, Zumret Topčagić 1, and Borut Drnovšek 1,2 1 Faculty of Electrical Engineering, University of Ljubljana, Ljubljana, Slovenia,

More information

IMPROVED DESIGN OF A LINEAR TRANSVERSE FLUX RELUCTANCE MOTOR

IMPROVED DESIGN OF A LINEAR TRANSVERSE FLUX RELUCTANCE MOTOR IMPROVED DESIGN OF A LINEAR TRANSVERSE FLUX RELUCTANCE MOTOR D.C. Popa, V. Iancu and L. Szabó Technical University Cluj-Napoca/Electrical Machines Department, Cluj-Napoca, Romania Abstract The paper deals

More information

Optimum design of a double-sided permanent magnet linear synchronous motor to minimize the detent force

Optimum design of a double-sided permanent magnet linear synchronous motor to minimize the detent force Energy Equip. Sys./ Vol. 5/No1/March 2017/ 1-11 Energy Equipment and Systems http://energyequipsys.ut.ac.ir www.energyequipsys.com Optimum design of a double-sided permanent magnet linear synchronous motor

More information

MODELING surface-mounted permanent-magnet (PM)

MODELING surface-mounted permanent-magnet (PM) Modeling of Axial Flux Permanent-Magnet Machines Asko Parviainen, Markku Niemelä, and Juha Pyrhönen Abstract In modeling axial field machines, three dimensional (3-D) finite-element method (FEM) models

More information

Cogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing

Cogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing EVS28 KINTEX, Korea, May 3-6, 215 Cogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing Soo-Gyung Lee 1, Kyung-Tae Jung 1, Seung-Hee Chai 1, and Jung-Pyo

More information

Research Article Electromagnetic and Mechanical Characteristics Analysis of a Flat-Type Vertical-Gap Passive Magnetic Levitation Vibration Isolator

Research Article Electromagnetic and Mechanical Characteristics Analysis of a Flat-Type Vertical-Gap Passive Magnetic Levitation Vibration Isolator Shock and Vibration Volume 6, Article ID 577, pages http://dx.doi.org/.55/6/577 Research Article Electromagnetic and Mechanical Characteristics Analysis of a Flat-Type Vertical-Gap Passive Magnetic Levitation

More information

Development of a Compressor for a Miniature Pulse Tube Cryocooler of 2.5 W at 65 K

Development of a Compressor for a Miniature Pulse Tube Cryocooler of 2.5 W at 65 K Development of a Compressor for a Miniature Pulse Tube Cryocooler of 2.5 W at 65 K N. Matsumoto, Y. Yasukawa, K. Ohshima, T. Takeuchi, K. Yoshizawa, T. Matsushita, Y. Mizoguchi, and A. Ikura Fuji Electric

More information

Development of axial flux HTS induction motors

Development of axial flux HTS induction motors Available online at www.sciencedirect.com Procedia Engineering 35 (01 ) 4 13 International Meeting of Electrical Engineering Research ENIINVIE-01 Development of axial flux HTS induction motors A. González-Parada

More information

Optimisation of Inner Diameter to Outer Diameter Ratio of Axial Flux Permanent Magnet Generator

Optimisation of Inner Diameter to Outer Diameter Ratio of Axial Flux Permanent Magnet Generator IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 220-1, Volume 9, Issue 6 Ver. III (Nov Dec. 2014), PP 4-47 Optimisation of Inner Diameter to Outer Diameter

More information

Normal Force and Vibration Analysis of Linear Permanent-Magnet Vernier Machine

Normal Force and Vibration Analysis of Linear Permanent-Magnet Vernier Machine Journal of Magnetics 22(4), 579-589 (207) ISSN (Print) 226-750 ISSN (Online) 22-6656 https://doi.org/0.428/jmag.207.22.4.579 Normal Force and Vibration Analysis of Linear Permanent-Magnet Vernier Machine

More information

Third harmonic current injection into highly saturated multi-phase machines

Third harmonic current injection into highly saturated multi-phase machines ARCHIVES OF ELECTRICAL ENGINEERING VOL. 66(1), pp. 179-187 (017) DOI 10.1515/aee-017-001 Third harmonic current injection into highly saturated multi-phase machines FELIX KLUTE, TORBEN JONSKY Ostermeyerstraße

More information

Journal of System Design and Dynamics

Journal of System Design and Dynamics Zero Power Non-Contact Suspension System with Permanent Magnet Motion Feedback* Feng SUN** and Koichi OKA** ** Kochi University of Technology 185 Miyanokuchi, Tosayamada, Kami city, Kochi 782-8502, Japan

More information

Analytical Solution of Magnetic Field in Permanent-Magnet Eddy-Current Couplings by Considering the Effects of Slots and Iron-Core Protrusions

Analytical Solution of Magnetic Field in Permanent-Magnet Eddy-Current Couplings by Considering the Effects of Slots and Iron-Core Protrusions Journal of Magnetics 20(3), 273-283 (2015) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 http://dx.doi.org/10.4283/jmag.2015.20.3.273 Analytical Solution of Magnetic Field in Permanent-Magnet Eddy-Current

More information

Concept Design and Performance Analysis of HTS Synchronous Motor for Ship Propulsion. Jin Zou, Di Hu, Mark Ainslie

Concept Design and Performance Analysis of HTS Synchronous Motor for Ship Propulsion. Jin Zou, Di Hu, Mark Ainslie Concept Design and Performance Analysis of HTS Synchronous Motor for Ship Propulsion Jin Zou, Di Hu, Mark Ainslie Bulk Superconductivity Group, Engineering Department, University of Cambridge, CB2 1PZ,

More information

This is a repository copy of Influence of skew and cross-coupling on flux-weakening performance of permanent-magnet brushless AC machines.

This is a repository copy of Influence of skew and cross-coupling on flux-weakening performance of permanent-magnet brushless AC machines. This is a repository copy of Influence of skew and cross-coupling on flux-weakening performance of permanent-magnet brushless AC machines. White Rose Research Online URL for this paper: http://eprints.whiterose.ac.uk/8610/

More information

A Numerical Study on Static and Dynamic Characteristics of Electromagnetic Air Compressor used in Household Refrigerators

A Numerical Study on Static and Dynamic Characteristics of Electromagnetic Air Compressor used in Household Refrigerators Journal of Experimental & Applied Mechanics ISSN: 2230-9845 (online), ISSN: 2321-516X (print) Volume 5, Issue 3 www.stmjournals.com A Numerical Study on Static and Dynamic Characteristics of Electromagnetic

More information

Research Article Low Frequency Axial Flux Linear Oscillating Electric Drive Suitable for Short Strokes

Research Article Low Frequency Axial Flux Linear Oscillating Electric Drive Suitable for Short Strokes IRN Electronics, Article ID 765161, 5 pages http://dx.doi.org/10.1155/2014/765161 Research Article Low Frequency Axial Flux Linear Oscillating Electric Drive uitable for hort trokes Govindaraj Thangavel

More information

DESIGN OF A LINEAR DC MOTOR FOR HIGH THRUST CONSTANTS CHARACTERISTICS

DESIGN OF A LINEAR DC MOTOR FOR HIGH THRUST CONSTANTS CHARACTERISTICS VOL., NO., JULY ISSN 9- - Asian Research Publishing Network (ARPN). All rights reserved. DESIGN OF A LINEAR DC MOTOR FOR HIGH THRUST CONSTANTS CHARACTERISTICS F. Azhar, R. N. Firdaus and M. L. Mohd Jamil

More information

Analysis and Case Study of Permanent Magnet Arrays for Eddy Current Brake Systems with a New Performance Index

Analysis and Case Study of Permanent Magnet Arrays for Eddy Current Brake Systems with a New Performance Index Journal of Magnetics 18(3), 276-282 (2013) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 http://dx.doi.org/10.4283/jmag.2013.18.3.276 Analysis and Case Study of Permanent Magnet Arrays for Eddy Current

More information

Analytical Model for Permanent Magnet Motors With Surface Mounted Magnets

Analytical Model for Permanent Magnet Motors With Surface Mounted Magnets 386 IEEE TRANSACTIONS ON ENERGY CONVERSION, VOL. 18, NO. 3, SEPTEMBER 2003 Analytical Model for Permanent Magnet Motors With Surface Mounted Magnets Amuliu Bogdan Proca, Member, IEEE, Ali Keyhani, Fellow,

More information

AXIAL FLUX INTERIOR PERMANENT MAGNET SYNCHRONOUS MOTOR WITH SINUSOIDALLY SHAPED MAGNETS

AXIAL FLUX INTERIOR PERMANENT MAGNET SYNCHRONOUS MOTOR WITH SINUSOIDALLY SHAPED MAGNETS AXIAL FLUX INTERIOR PERMANENT MAGNET SYNCHRONOUS MOTOR WITH SINUSOIDALLY SHAPED MAGNETS A. Parviainen, J. Pyrhönen, M. Niemelä Lappeenranta University of Technology, Department of Electrical Engineering

More information

Cogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing

Cogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing EVS28 KINTEX, Korea, May 3-6, 215 Cogging Torque Reduction in Surface-mounted Permanent Magnet Synchronous Motor by Axial Pole Pairing Soo-Gyung Lee 1, Kyung-Tae Jung 1, Seung-Hee Chai 1, and Jung-Pyo

More information

Publication P Institute of Electrical and Electronics Engineers (IEEE)

Publication P Institute of Electrical and Electronics Engineers (IEEE) Publication P2 Jere Kolehmainen and Jouni Ikäheimo. 2008. Motors with buried magnets for medium-speed applications. IEEE Transactions on Energy Conversion, volume 23, number 1, pages 86-91. 2008 Institute

More information

Design Optimization and Development of Linear Brushless Permanent Magnet Motor

Design Optimization and Development of Linear Brushless Permanent Magnet Motor International Journal of Control, Automation, and Systems Vol. 1, No. 3, September 3 351 Design Optimization and Development of Linear Brushless Permanent Magnet Motor Myung-Jin Chung and Dae-Gab Gweon

More information

Stability Analysis and Research of Permanent Magnet Synchronous Linear Motor

Stability Analysis and Research of Permanent Magnet Synchronous Linear Motor Stability Analysis and Research of Permanent Magnet Synchronous Linear Motor Abstract Rudong Du a, Huan Liu b School of Mechanical and Electronic Engineering, Shandong University of Science and Technology,

More information

Development of a Double-Sided Consequent Pole Linear Vernier Hybrid Permanent-Magnet Machine for Wave Energy Converters

Development of a Double-Sided Consequent Pole Linear Vernier Hybrid Permanent-Magnet Machine for Wave Energy Converters Development of a Double-Sided Consequent Pole Linear Vernier Hybrid Permanent-Magnet Machine for Wave Energy Converters A. A. Almoraya, N. J. Baker, K. J. Smith and M. A. H. Raihan Electrical Power Research

More information

Analysis of the Influence of Different Topologies on a TLSRG Generation Performance for WEC

Analysis of the Influence of Different Topologies on a TLSRG Generation Performance for WEC Analysis of the Influence of Different Topologies on a TLSRG Generation Performance for WEC R.P.G. Mendes, M.R.A. Calado and S.J.P.S. Mariano Abstract In this work, 4 structural configurations are proposed,

More information

LINEAR MOTORS produce a direct thrust force without

LINEAR MOTORS produce a direct thrust force without 5436 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 60, NO. 12, DECEMBER 2013 Investigation and General Design Principle of a New Series of Complementary and Modular Linear FSPM Motors Ruiwu Cao, Student

More information

Analysis of Halbach magnet array and its application to linear motor

Analysis of Halbach magnet array and its application to linear motor Mechatronics 14 (2004) 115 128 Analysis of Halbach magnet array and its application to linear motor Moon G. Lee, Sung Q. Lee, Dae-Gab Gweon * Department of Mechanical Engineering, Korea Advanced Institute

More information

Design of the Forced Water Cooling System for a Claw Pole Transverse Flux Permanent Magnet Synchronous Motor

Design of the Forced Water Cooling System for a Claw Pole Transverse Flux Permanent Magnet Synchronous Motor Design of the Forced Water Cooling System for a Claw Pole Transverse Flux Permanent Magnet Synchronous Motor Ahmad Darabi 1, Ali Sarreshtehdari 2, and Hamed Tahanian 1 1 Faculty of Electrical and Robotic

More information

THERMAL FIELD ANALYSIS IN DESIGN AND MANUFACTURING OF A PERMANENT MAGNET LINEAR SYNCHRONOUS MOTOR

THERMAL FIELD ANALYSIS IN DESIGN AND MANUFACTURING OF A PERMANENT MAGNET LINEAR SYNCHRONOUS MOTOR THERMAL FIELD ANALYSIS IN DESIGN AND MANUFACTURING OF A PERMANENT MAGNET LINEAR SYNCHRONOUS MOTOR Petar UZUNOV 1 ABSTRACT: The modern Permanent Magnet Linear Synchronous Motors (PMLSM) has a wide range

More information

Design and Analysis of a Linear Permanent- Magnet Vernier Machine With Improved Force Density

Design and Analysis of a Linear Permanent- Magnet Vernier Machine With Improved Force Density 2072 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 63, NO. 4, APRIL 2016 Design and Analysis of a Linear Permanent- Magnet Vernier Machine With Improved Force Density Wenxiang Zhao, Senior Member,

More information

Influence of Segmentation of Ring-Shaped NdFeB Magnets with Parallel Magnetization on Cylindrical Actuators

Influence of Segmentation of Ring-Shaped NdFeB Magnets with Parallel Magnetization on Cylindrical Actuators Sensors 14, 14, 137-1387; doi:1.339/s147137 Article OPEN ACCESS sensors ISSN 144-8 www.mdpi.com/journal/sensors Influence of Segmentation of Ring-Shaped NdFeB Magnets with Parallel Magnetization on Cylindrical

More information

Levitation and Thrust Forces Analysis of Hybrid-Excited Linear Synchronous Motor for Magnetically Levitated Vehicle

Levitation and Thrust Forces Analysis of Hybrid-Excited Linear Synchronous Motor for Magnetically Levitated Vehicle 564 Journal of Electrical Engineering & Technology Vol. 7, No. 4, pp. 564~569, 2012 http://dx.doi.org/10.5370/jeet.2012.7.4.564 Levitation and Thrust Forces Analysis of Hybrid-Excited Linear Synchronous

More information

EE 410/510: Electromechanical Systems Chapter 4

EE 410/510: Electromechanical Systems Chapter 4 EE 410/510: Electromechanical Systems Chapter 4 Chapter 4. Direct Current Electric Machines and Motion Devices Permanent Magnet DC Electric Machines Radial Topology Simulation and Experimental Studies

More information

Performance Evaluation and Comparison of Switched Reluctance Cylindrical Linear Motor

Performance Evaluation and Comparison of Switched Reluctance Cylindrical Linear Motor Performance Evaluation and Comparison of Switched Reluctance Cylindrical Linear Motor. Azhar* 1, H. Wakiwaka* 1, K. Tashiro* 1, H. Yajima* 2, T. Kanazawa* 2 and N. ujiwara* 2 Nowadays, most of the researchers

More information

Measurement And Testing. Handling And Storage. Quick Reference Specification Checklist

Measurement And Testing. Handling And Storage. Quick Reference Specification Checklist Design Guide Contents Introduction Manufacturing Methods Modern Magnet Materials Coatings Units Of Measure Design Considerations Permanent Magnet Stability Physical Characteristics And Machining Of Permanent

More information

Finite Element Analysis of Hybrid Excitation Axial Flux Machine for Electric Cars

Finite Element Analysis of Hybrid Excitation Axial Flux Machine for Electric Cars 223 Finite Element Analysis of Hybrid Excitation Axial Flux Machine for Electric Cars Pelizari, A. ademir.pelizari@usp.br- University of Sao Paulo Chabu, I.E. ichabu@pea.usp.br - University of Sao Paulo

More information

Flux: Examples of Devices

Flux: Examples of Devices Flux: Examples of Devices xxx Philippe Wendling philippe.wendling@magsoft-flux.com Create, Design, Engineer! www.magsoft-flux.com www.cedrat.com Solenoid 2 1 The Domain Axisymmetry Open Boundary 3 Mesh

More information

A Permanent Magnet Linear Synchronous Motor Drive for HTS Maglev Transportation Systems

A Permanent Magnet Linear Synchronous Motor Drive for HTS Maglev Transportation Systems JOURNAL OF ELECTRONIC SCIENCE AND TECHNOLOGY OF CHINA, VOL. 6, NO., JUNE 008 5 A Permanent Magnet Linear Synchronous Motor Drive for HTS Maglev Transportation Systems You-Guang Guo, Jian-Xun Jin, Lu-Hai

More information

Design and Characteristic Analysis of LSM for High Speed Train System using Magnetic Equivalent Circuit

Design and Characteristic Analysis of LSM for High Speed Train System using Magnetic Equivalent Circuit IJR International Journal of Railway Vol. 3, No. 1 / March 2010, pp. 14-18 The Korean Society for Railway Design and Characteristic Analysis of LSM for High Speed Train System using Magnetic Equivalent

More information

CPPM Mahine: A Synchronous Permanent Magnet Machine with Field Weakening

CPPM Mahine: A Synchronous Permanent Magnet Machine with Field Weakening CPPM Mahine: A Synchronous Permanent Magnet Machine with Field Weakening Juan A. Tapia, Thomas A. Lipo, Fellow, IEEE Dept. of Electrical and Computer Engineering University of Wisconsin-Madison 45 Engineering

More information

Prof. A. K. Al-Shaikhli, Asst. Prof. Abdul-Rahim T. Humod, Fadhil A. Hasan*

Prof. A. K. Al-Shaikhli, Asst. Prof. Abdul-Rahim T. Humod, Fadhil A. Hasan* International Journal of Scientific & Engineering Research, Volume 6, Issue 1, January-2015 174 Analysis of Heat Distribution for Different Types of Traveling Wave Induction Heater Based On 3D FEM Prof.

More information

This is a repository copy of Analytical modelling of modular and unequal tooth width surface-mounted permanent magnet machines.

This is a repository copy of Analytical modelling of modular and unequal tooth width surface-mounted permanent magnet machines. This is a repository copy of Analytical modelling of modular and unequal tooth width surface-mounted permanent magnet machines. White Rose Research Online URL for this paper: http://eprints.whiterose.ac.uk/86803/

More information

Keywords: Electric Machines, Rotating Machinery, Stator faults, Fault tolerant control, Field Weakening, Anisotropy, Dual rotor, 3D modeling

Keywords: Electric Machines, Rotating Machinery, Stator faults, Fault tolerant control, Field Weakening, Anisotropy, Dual rotor, 3D modeling Analysis of Electromagnetic Behavior of Permanent Magnetized Electrical Machines in Fault Modes M. U. Hassan 1, R. Nilssen 1, A. Røkke 2 1. Department of Electrical Power Engineering, Norwegian University

More information

Water-Cooled Direct Drive Permanent Magnet Motor Design in Consideration of its Efficiency and Structural Strength

Water-Cooled Direct Drive Permanent Magnet Motor Design in Consideration of its Efficiency and Structural Strength Journal of Magnetics 18(2), 125-129 (2013) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 http://dx.doi.org/10.4283/jmag.2013.18.2.125 Water-Cooled Direct Drive Permanent Magnet Motor Design in Consideration

More information

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International licence

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International licence Wu D, Jalal AS, Baker N. A coupled model of the Linear Joule Engine integrated with a tubular permanent magnet linear alternator. In: The 8th International Conference on Applied Energy (ICAE2016. 2016,

More information

High Efficiency LSM with High Flux Density for Transportation

High Efficiency LSM with High Flux Density for Transportation Journal of Transportation Technologies,,, -6 doi:.436/jtts..43 Published Online October (http://www.scirp.org/journal/jtts) High Efficiency LSM with High Flux Density for Transportation Abstract Nobuo

More information

Suppression of thrust fluctuation of doubly-fed linear motor

Suppression of thrust fluctuation of doubly-fed linear motor Journal of Modern Transportation Volume 0 Number June 0 Page 03-07 Journal homepage: jmtswjtueducn DOI: 0007/BF0335786 Suppression of thrust fluctuation of doubly-fed linear motor Ying WANG * Kunlun ZHANG

More information

Design of a high-speed superconducting bearingless machine for flywheel energy storage systems. Li, WL; Chau, KT; Ching, TW; Wang, Y; CHEN, M

Design of a high-speed superconducting bearingless machine for flywheel energy storage systems. Li, WL; Chau, KT; Ching, TW; Wang, Y; CHEN, M Title Design of a high-speed superconducting bearingless machine for flywheel energy storage systems Author(s) Li, WL; Chau, KT; Ching, TW; Wang, Y; CHEN, M Citation IEEE Transactions on Applied Superconductivity,

More information

A Novel Pseudo-Direct-Drive Permanent-Magnet Machine with Less Magnet

A Novel Pseudo-Direct-Drive Permanent-Magnet Machine with Less Magnet Machine Copy for Proofreading, Vol. x, y z, 2016 A Novel Pseudo-Direct-Drive Permanent-Magnet Machine with Less Magnet Xin Yin, Pierre-Daniel Pfister * and Youtong Fang Abstract Magnetic gears (MGs), an

More information

Robust optimal design of a magnetizer to reduce the harmonic components of cogging torque in a HDD spindle motor

Robust optimal design of a magnetizer to reduce the harmonic components of cogging torque in a HDD spindle motor Microsyst Technol (2014) 20:1497 1504 DOI 10.1007/s00542-014-2153-4 Technical Paper Robust optimal design of a magnetizer to reduce the harmonic components of cogging torque in a HDD spindle motor Changjin

More information

DESIGN AND ANALYSIS OF AXIAL-FLUX CORELESS PERMANENT MAGNET DISK GENERATOR

DESIGN AND ANALYSIS OF AXIAL-FLUX CORELESS PERMANENT MAGNET DISK GENERATOR DESIGN AND ANALYSIS OF AXIAL-FLUX CORELESS PERMANENT MAGNET DISK GENERATOR Łukasz DR ZIKOWSKI Włodzimierz KOCZARA Institute of Control and Industrial Electronics Warsaw University of Technology, Warsaw,

More information

IEEE Transactions on Applied Superconductivity. Copyright IEEE.

IEEE Transactions on Applied Superconductivity. Copyright IEEE. Title Loss analysis of permanent magnet hybrid brushless machines with and without HTS field windings Author(s) Liu, C; Chau, KT; Li, W Citation The 21st International Conference on Magnet Technology,

More information

This is a repository copy of Improved analytical model for predicting the magnetic field distribution in brushless permanent-magnet machines.

This is a repository copy of Improved analytical model for predicting the magnetic field distribution in brushless permanent-magnet machines. This is a repository copy of Improved analytical model for predicting the magnetic field distribution in brushless permanent-magnet machines. White Rose Research Online URL for this paper: http://eprints.whiterose.ac.uk/874/

More information

Static Characteristics of Switched Reluctance Motor 6/4 By Finite Element Analysis

Static Characteristics of Switched Reluctance Motor 6/4 By Finite Element Analysis Australian Journal of Basic and Applied Sciences, 5(9): 1403-1411, 2011 ISSN 1991-8178 Static Characteristics of Switched Reluctance Motor 6/4 By Finite Element Analysis 1 T. Jahan. 2 M.B.B. Sharifian

More information

SPOKE-TYPE permanent magnet (PM) rotors are typically

SPOKE-TYPE permanent magnet (PM) rotors are typically Magnetic End Leakage Flux in a Spoke Type Rotor Permanent Magnet Synchronous Generator Petter Eklund, Jonathan Sjölund, Sandra Eriksson, Mats Leijon Abstract The spoke type rotor can be used to obtain

More information

Analysis of Idle Power and Iron Loss Reduction in an Interior PM Automotive Alternator

Analysis of Idle Power and Iron Loss Reduction in an Interior PM Automotive Alternator Analysis of Idle Power and Iron Loss Reduction in an Interior PM Automotive Alternator by Vlatka Životić-Kukolj M.Eng.Sci. (Research) Electrical and Electronic Engineering, Adelaide University, 2001 B.Eng

More information

ON THE PARAMETERS COMPUTATION OF A SINGLE SIDED TRANSVERSE FLUX MOTOR

ON THE PARAMETERS COMPUTATION OF A SINGLE SIDED TRANSVERSE FLUX MOTOR ON THE PARAMETERS COMPUTATION OF A SINGLE SIDED TRANSVERSE FLUX MOTOR Henneberger, G. 1 Viorel, I. A. Blissenbach, R. 1 Popan, A.D. 1 Department of Electrical Machines, RWTH Aachen, Schinkelstrasse 4,

More information

THE magnetic fluxes in the stator and rotor yokes of

THE magnetic fluxes in the stator and rotor yokes of Analytical Calculation of Yoke Flux Patterns in Fractional-Slot Permanent Magnet Machines Astrid Røkke and Robert Nilssen Department of Electric Power Engineering, Norwegian University of Science and Technology,

More information

Performance analysis of variable speed multiphase induction motor with pole phase modulation

Performance analysis of variable speed multiphase induction motor with pole phase modulation ARCHIVES OF ELECTRICAL ENGINEERING VOL. 65(3), pp. 425-436 (2016) DOI 10.1515/aee-2016-0031 Performance analysis of variable speed multiphase induction motor with pole phase modulation HUIJUAN LIU, JUN

More information

Dr. N. Senthilnathan (HOD) G. Sabaresh (PG Scholar) Kongu Engineering College-Perundurai Dept. of EEE

Dr. N. Senthilnathan (HOD) G. Sabaresh (PG Scholar) Kongu Engineering College-Perundurai Dept. of EEE Design and Optimization of 4.8kW Permanent MagNet Brushless Alternator for Automobile G. Sabaresh (PG Scholar) Kongu Engineering College-Perundurai Dept. of EEE sabareshgs@gmail.com 45 Dr. N. Senthilnathan

More information

Energy balance in self-powered MR damper-based vibration reduction system

Energy balance in self-powered MR damper-based vibration reduction system BULLETIN OF THE POLISH ACADEMY OF SCIENCES TECHNICAL SCIENCES, Vol. 59, No. 1, 2011 DOI: 10.2478/v10175-011-0011-4 Varia Energy balance in self-powered MR damper-based vibration reduction system J. SNAMINA

More information

White Rose Research Online URL for this paper:

White Rose Research Online URL for this paper: This is a repository copy of Eddy-current loss in the rotor magnets of permanent-magnet brushless machines having a fractional number of slots per pole. White Rose Research Online URL for this paper: http://eprints.whiterose.ac.uk/861/

More information

PERMANENT MAGNET EXCITED TRANSVERSE FLUX LINEAR MOTOR WITH INNER MOVER FOR ROPELESS ELEVATOR

PERMANENT MAGNET EXCITED TRANSVERSE FLUX LINEAR MOTOR WITH INNER MOVER FOR ROPELESS ELEVATOR PERMANENT MAGNET EXCITED TRANSVERSE FLUX LINEAR MOTOR WITH INNER MOVER FOR ROPELESS ELEVATOR DRAGOŞ OVIDIU KISCK 1, DO HYUN KANG 2, JUNG HWAN CHANG 2, JI WON KIM 2, DRAGOŞ ANGHEL 1 Key words: Linear motor,

More information

Characteristics Analysis of Claw-Pole Alternator for Automobiles by Nonlinear Magnetic Field Decomposition for Armature Reaction

Characteristics Analysis of Claw-Pole Alternator for Automobiles by Nonlinear Magnetic Field Decomposition for Armature Reaction IEEJ Journal of Industry Applications Vol.6 No.6 pp.362 369 DOI: 10.1541/ieejjia.6.362 Paper Characteristics Analysis of Claw-Pole Alternator for Automobiles by Nonlinear Magnetic Field Decomposition for

More information

Analytical Model for Sizing the Magnets of Permanent Magnet Synchronous Machines

Analytical Model for Sizing the Magnets of Permanent Magnet Synchronous Machines Journal of Electrical Engineering 3 (2015) 134-141 doi: 10.17265/2328-2223/2015.03.004 D DAVID PUBLISHING Analytical Model for Sizing Magnets of Permanent Magnet Synchronous Machines George Todorov and

More information

THEORETICAL AND EXPERIMENTAL STUDY OF A MODULAR TUBULAR TRANSVERSE FLUX RELUC- TANCE MACHINE

THEORETICAL AND EXPERIMENTAL STUDY OF A MODULAR TUBULAR TRANSVERSE FLUX RELUC- TANCE MACHINE Progress In Electromagnetics Research, Vol. 139, 41 55, 2013 THEORETICAL AND EXPERIMENTAL STUDY OF A MODULAR TUBULAR TRANSVERSE FLUX RELUC- TANCE MACHINE Dan-Cristian Popa *, Vasile-Ioan Gliga, and Loránd

More information

PRINCIPLE OF DESIGN OF FOUR PHASE LOW POWER SWITCHED RELUCTANCE MACHINE AIMED TO THE MAXIMUM TORQUE PRODUCTION

PRINCIPLE OF DESIGN OF FOUR PHASE LOW POWER SWITCHED RELUCTANCE MACHINE AIMED TO THE MAXIMUM TORQUE PRODUCTION Journal of ELECTRICAL ENGINEERING, VOL. 55, NO. 5-6, 24, 138 143 PRINCIPLE OF DESIGN OF FOUR PHASE LOW POWER SWITCHED RELUCTANCE MACHINE AIMED TO THE MAXIMUM TORQUE PRODUCTION Martin Lipták This paper

More information

Maglev by a passive HT C superconducting short runner above the magnetic guideway

Maglev by a passive HT C superconducting short runner above the magnetic guideway Maglev by a passive HT C superconducting short runner above the magnetic guideway G. D Ovidio 1, F. Crisi 2, A. Navarra 2 & G. Lanzara 1 1 Transportation Department, University of L Aquila, Italy 2 Science

More information

Design and analysis of a HTS vernier PM machine. IEEE Transactions on Applied Superconductivity. Copyright IEEE.

Design and analysis of a HTS vernier PM machine. IEEE Transactions on Applied Superconductivity. Copyright IEEE. Title Design and analysis of a HTS vernier PM machine Author(s) Li, J; Chau, KT Citation Ieee Transactions On Applied Superconductivity, 2010, v. 20 n. 3, p. 1055-1059 Issued Date 2010 URL http://hdl.handle.net/10722/129194

More information