Introduction to Properties and The Elastic Modulus

Size: px
Start display at page:

Download "Introduction to Properties and The Elastic Modulus"

Transcription

1 09 A. K. M. B. Rashid Professor, Department of MME BUET, Dhaka Introduction to Properties and The Elastic Modulus Topics to Cover Introduction to properties Introduction to mechanical properties The elastic modulus References: 1. Ashby and Jones. Engineering Materials 1, 3 rd Ed, Ch01 (pp.1-8), Ch03 (pp.29-42), Ch06 (pp.83-87). 2. Callister & Rethwisch. Materials Science and Engineering: An Introduction, 9 th Ed, Ch06 (pp , ).

2 Introduction to Properties An engineer has a vast range of materials at his disposal: metals and alloys, polymers, glasses and ceramics, composites How does he go about selecting the material, or combination of materials, which best suit his purpose? by selecting properties Mistakes can cause disasters. SS John P. Gaines split in two (1943) 3/34 Case Study 1: Plastic-handled screwdriver Shaft and blade high-carbon steel (metal) High modulus (of elasticity), measuring the resistance of the material to elastic deflection or bending (a.k.a. stiffness). A polymer, if used, would twist far too much. High yield strength, measuring the resistance to cause permanent deformation, so that it would not bend plastically or permanently if twist it hard. Why not use glass? High hardness, measuring the resistance to cause localized deformation, otherwise it would be indented by the material of the head of the screw and damaged. Must have high fracture toughness (energy required to cause brittle fracture) to resist brittle fracture, so that it gives or bends before it breaks. 4/34

3 Handle Perspex (polymer/plastic) Have large section, so its twisting or modulus is less important. Cannot be made using rubber, since its modulus is too low. Cannot be used metal either, because it is too heavy. Other commonly used material is wood, a rather complicated but cheap polymer. Perspex (Poly-methly-meth-acrylate, PMMA) is preferred because of its ease of fabrication soft and moulded easily when hot aesthetic value appearance, feel, texture are right low density not unnecessarily tiring to hold Low cost 5/34 Case Study 2: Rolls-Royce RB211 turbofan aero-engine Air is compressed into the engine by turbofan, which also provides the aerodynamic thrust around the outside of the casing. Air is further compressed by the compressor blades, then mixed with fuel and burnt in the combustion chamber. The expanding gases drives the turbine blades, which provide power to the turbofan and the compressor blade, and finally pass out of the rear of the engine, contributing to the thrust. Turbine blades Compressor blades Turbofan 6/34

4 Turbofan blade Titanium alloy (metal) Good modulus, yield strength, fracture toughness. Must also resist fatigue failure (due to rapid fluctuating loads) surface wear (from striking water droplets at high speed) corrosion (important when taking off over the sea) inally, it must have low density. Why not use composite blades of CRP (carbon fibre-reinforced plastics)? Engine blade Complex nickel-base superalloys (metal) Requirements additional to those used for turbofan blade must be used. or economy, fuel must be burnt at as high temperature as possible. The first row of engine blades nowadays runs at about 950 C. This adds high creep and oxidation resistance to the requirement. Although it has a density less than one-half of that of titanium alloy, it is simply not tough enough even a bird strike would instantly demolish a CRP turbofan. 7/34 Case Study 3: Sparking plug for IC engine Spark electrode Tungsten alloy Resistant to thermal fatigue (from rapidly fluctuating temperature) wear (from spark erosion) oxidation and corrosion (from hot gases containing S and Pb) Insulation Alumina (ceramic) Good electrical insulation Good resistance to thermal fatigue, corrosion and oxidation 8/34

5 Summaries of Properties Bulk Mechanical Properties Density Modulus Yield strength, tensile strength, and ductility Hardness Impact strength and fracture toughness atigue strength and thermal fatigue resistance Creep strength Bulk Non-mechanical Properties Physical properties melting point Thermal properties thermal stability, heat capacity, thermal expansion, thermal conductivity Magnetic properties para-, dia-, and ferromagnetic properties Chemical properties corrosion and oxidation Optical properties refractive index, colour, light absorption, reflection and transmission Electrical properties electrical conductivity, dielectric properties Production properties Ease of manufacture Castability Heat treatability Economic properties Price and availability Surface properties Hardenability ormability Machinability Weldability Oxidation and corrosion riction, abrasion, and wear Aesthetic properties Appearance, texture, feel 9/34 Price and Availability of Materials Table 1.3: Breakdown of Material Prices Class of Use Material Price per ton Basic construction Wood, concrete, structural steel US$200 $500 Medium and light Metals, alloys and polymers for aircraft, US$500 $30,000 Engineering automobiles, appliances, etc. Special materials Turbine-blade alloys, advanced composites. US$30,000 $100,000 (CRP, BRP), etc Precious metals, etc. Sapphire bearings, silver contacts, gold microcircuits, US$100,000 $60m industrial diamond cutting and polishing tools Availability of Materials Depends upon 3 factors: Degree of localization The size of the reserves (the resource base) The energy required to mine and process Critically important in materials selection process Materials for large-scale structural use Lowest price Many materials have all property requirements but their use is eliminated by their price Materials for light and mediumengineering work Larger value addition Lesser economic constraint High labour and production / fabrication cost Severe competition Materials for high-performance applications Regime of high materials technology Actively under research Intense competition from new materials 10/34

6 Introduction to Mechanical Properties rom an application standpoint, one of the most important topics within MME is the study of the mechanical behavior of material i.e. how materials respond or deform in relation to an applied load or force. Most components, even if used primarily for other property (electronic properties, for example) have to fulfill certain mechanical functions as well. It is necessary to know the characteristics of the material so that any resulting deformation will not be excessive and fracture will not occur. Laboratory testing to measure mechanical properties attempts to replicate the service conditions. Consistency is accomplished by using standardized test, so that people are measuring same thing in the same way. Many international bodies like American Society for Testing Materials (ASTM) maintains and updates standards for mechanical properties. Several other standards organizations include BDS, IS, SAE, ANSI, BS, ISO, JS, DIN, etc. Important mechanical properties are: strength, ductility, stiffness, toughness and hardness. 11/34 What happens to material when it is loaded with a mechanical force? A 0 A 0 τ θ τ l l 0 l 0 l θ A 0 pulling or stretching squeezing or squashing sliding twisting Material deforms, either elastically (i.e. temporarily), or, plastically (i.e. permanently) depending on the magnitude of the force applied. 12/34

7 Elastic Deformation Initial state Small load applied Load removed bonds stretched bonds return to initial state d Linear elastic Elastic means reversible!! Non-linear elastic This happens when strains (i.e. deformations) are small (~0.5%) (except for the case of polymers) d 13/34 Plastic Deformation 1. Initial state 2. Large load applied 3. Unload Load removed bonds stretched and planes sheared bond un-stretched, but planes still sheared d e+p Plastic deformation, d p Elastic deformation, d e Plastic means permanent!! linear elastic d p d e d

8 The Elastic Modulus Elastic modulus measures the resistance of the material to elastic or springy deformation. Low modulus materials are floppy, and stretch a lot when they are pulled (squash down a lot when pushed). High modulus materials are the opposite they stretch very little when pulled (squash down very little when pushed). loppy materials like rubber are ideal for things like bungee-jumping ropes Steels are ideally used for making bridges precisely because it is stiff in tension and doesn t give Stretching of a rubber band Sydney Harbour Bridge it is very easy to stretch a rubber band it would be useless if you couldn t but there is no way you could stretch a strip of steel of this cross-section using you bare hands. What will happen if someone uses steel wire rope for climbing protection, or some designer uses rubber to build a bridge? 15/34 Concept of Stress and Strain Stress - orce or load per unit area of cross-section over which the force or load is acting t s Stress is considered positive for tensile loads, negative for compressive loads A A s Important point magnitude of a stress is always equal to the magnitude of a force divided by the area of the face on which it acts Tensile stress σ = A t Tensile stress Shear stress σ = t A τ = s A

9 Common states of stress Common states of stress: tension, compression, hydrostatic pressure, and shear 17/34 orce, : Newton (N), kilogramme-force (kg f ), pound-force (lb f ) Area A : sq. metre (m 2 ), sq. centimeter (cm 2 ), sq. inch (in 2 ) Unit of Stress Newton per sq. metre (N m 2 ) Kilogramme-force per sq. centimeter (kg f cm 2 ) Pound-force per sq. inch or psi (lb f in 2 ) SI Unit of Stress Pascal (Pa) 1 Pa = 1 kg m 1 s 2 (Since, = ma = kg m s 2 ) Unit Conversion of Stress 1 Pa = N m 2 1 MPa = 1 Mega Pascal = 10 6 Pa 1 GPa = 1 Giga Pascal = 10 9 Pa 1 MPa = 1 MN m 2 = 1 N mm 2 = 145 psi Stresses/Pressure Convention Stress: positive when pull (in tension), negative when push (compression) Pressure: positive when it pushes, negative when pulls 18/34

10 Strain - Change in dimension (elongation) per unit length Strain is considered positive for tensile loads, negative for compressive loads w q l t w Engineering shear strain γ = w l = tanθ q for small strains P t p u/2 Nominal tensile strain ε n = u l V w Nominal lateral strain ε l = v w p V DV p l Poisson s ratio, ν = lateral strain tensile strain v/2 P v/2 u/2 Important Point Since strains are the ratios of two lengths or of two volumes, they are dimensionless. p Dilation (volume strain) Δ = ΔV V 19/34 Hooke s Law The elastic moduli are defined through Hooke s law. This is a description of the experimental observation that when strains are small the strain is very nearly proportional to the applied stress Such behavior of the solid is called linear elastic. Thus, for simple tension for example, the nominal tensile strain is proportional to the tensile stress s = E e n (Hooke s Law) Here E is called Young s modulus (of elasticity). Materials having a high value of E are termed as stiff, while those having a low value of E are called pliable, or floppy Hooke s law also holds good for stresses and strains in simple compression. In the same way, the shear strain is proportional to the shear stress, with t = G g G = shear modulus Also, the negative of the dilatation is proportional to the pressure (because positive pressure causes a shrinkage of volume) so that Important Point p = KD K = bulk modulus Because strain is dimensionless, the moduli have the same dimensions as those of stress.

11 Hooke s law (i.e. the linear relation between stress and strain) is very useful when calculating the response of a solid to stress. But many solids are elastic only to very small strains: up to about We defined Poisson s ratio as the ratio of the lateral shrinkage strain to the tensile strain. This quantity is also an elastic constant So altogether we have four elastic constants: Beyond that some break and some become plastic. A few solids, such as rubber, are elastic up to very much larger strains of order 4 or 5 E, G, K, u or many materials it is useful to know that but they cease to be linearly elastic (that is, the stress is no longer proportional to the strain) after a strain of about K E G 3 E/8 u 0:33 21/34 Measurement of Young s Modulus To measure Young s modulus, both stress and strain need to be measured with enough accuracy. In the case of metals, because they are stiff (and thus, strain data is very small), either the strain needs to be measured very accurately, or there needs to be some way of magnifying it. So we could load a bar of material in tension, having first glued strain gauges to its surface, and use the amplified electrical signal from them to measure the strain. Or, we could load a bar in bending and measure deflection for a given applied load. 22/34

12 3-Point bend test Compression test Especially easy geometry to adopt. Good for brittle materials (brittle metals, ceramics, polymers, composites), because if loaded in tension they may break where they are gripped by the testing machine. It is also good for natural composites, like wood or bamboo. loppy materials, like the lower modulus thermoplastics, rubbers and foamed polymers can be tested in compression strain is read directly from the movement of the testing machine. for such materials, the rate at which the specimen is strained has a significant effect on the modulus values calculated from the test. Three-point bend test 23/34 Velocity of sound method An electronic pulser-receiver is placed in contact with one end face of a short solid cylinder of the material. The times of travel of longitudinal and shear waves over the known distance are measured electronically, and used to determine the velocity of longitudinal waves, V L and the velocity of transverse waves, V T. V L = V T = ν = E 1 ν ρ 1 + ν 1 2ν G ρ 1/2 2 V 1 2 T VL 2 V 2 2 T VL 1/2 24/34

13 Worked Example 1 An aluminium rod is to withstand an applied force of 45,000 pounds. To assure a sufficient safety, the maximum allowable stress on the rod is limited to 25,000 psi. The rod must be at least 150 in. long but must deform elastically no more than 0.25 in. when the force is applied. Design an appropriate rod. Young s modulus for aluminium is 10x10 6 psi. Using the definition of stress, the required minimum cross-sectional area of the rod A = σ = lb lb/in 2 = 1.80 in2 or, d = 1.51 in However, the minimum length of rod is specified as 150 in. To produce a longer rod, we might make the cross-sectional area of the rod larger. The minimum strain allowed for the 150 in rod is ε = Δl l = 0.25 in 150 in = Using the Hook s law σ = E ε = 10x10 6 lb/in = lb/in 2 Then, the area required to withstand this stress A = σ = lb lb/in 2 = 2.70 in2 or, d = 1.85 in Thus, in order to satisfy both the maximum stress and the minimum elongation requirements, cross-sectional area of the rod must be at least 2.70 in 2, or a minimum diameter of 1.85 in. 25/34 Worked Example 2 Your friend wants to keep her large collection of books in a bookshelf in her sitting room. The bookshelf is 1600 mm wide and you offer to install a set of pine shelves, each 1600 mm long, supported at their ends on small brackets screwed into the wall. You guess that shelves measuring 20 mm deep (or thick) by 250 mm wide will work. However, professional integrity demands that you calculate the maximum stress and deflection first. or pine, E =10 GN m -2 and s y = 60 MN m -2. A book 40 mm thick weighs about 1 kg. 26/34

14 b l d I = 250 x = mm 4 = 1600 mm = 40 kgf 40 mm/kgf M = 40 kgf 9.81 N/kgf 1600 mm 8 = N mm σ max = N mm 20 mm/ mm 4 = 4.7 N mm 2 = 4.7 MPa δ = 5 40 kgf 9.81 N/kgf 1600 mm N mm mm 4 = 12.5 mm δ = l 2 E I I = b d3 12 σ max = M (d/2) I M = l 8 The shelves will not break but they will deflect noticeably. You are better advised to increase the thickness of the shelves. 27/34 Data for Young s Modulus Diamond, E = 1000 GPa Soft rubbers and foamed polymers, E < GPa Practical engineering materials, E = 10 3 to 10 3 GPa Ceramics and metals even the floppiest of them, like lead lie near the top of this range. Polymers and elastomers are much more compliant, the common ones (PE, PVC and PP) lying several decades lower. Composites span the range between polymers and ceramics. E (GPa) Why polymers are much less stiff than metals, and what we can do about it? What is the origin of the modulus? To answer these questions, we have to examine the structure of materials, and the nature of the forces holding the atoms together. 28/34

15 Physical Basis of Young s Modulus Two things are very important in determining the modulus: 1. The forces that hold atoms together (the interatomic bonds) which act like little springs, linking one atom to the next in the solid state. 2. The ways in which atoms pack together (the atom packing), since this determines how many little springs there are per unit area, and the angle at which they are pulled. The spring-like bond between two atoms Atom packing and bond-angle 29/34 orce required for any separation of the atoms rom the force/distance curve that we get = du dr 1. = 0 at the equilibrium point r = r 0 ; however, if the atoms are pulled apart by distance (r r 0 ), a resisting force appears. or small (r r 0 ), the resisting force is proportional to (r r 0 ) for all materials, in both tension and compression. 2. The stiffness, S, of the bond is given by S = d dr = d2 U dr 2 When the stretching is small, S is constant and equal to S 0 = d2 U dr 2 r=r 0 The bond behaves in linear elastic manner this is the physical origin of Hooke s law. the shape of the force/distance curve that we get from a typical energy/distance curve 30/34

16 S 0 = d2 U dr 2 r=r 0 S 0 is sometimes called the spring constant of the bond The force between a pair of atoms, stretched apart to a distance r (r r 0 ), is = S 0 r r 0 The total force exerted across unit area, if the two planes are pulled apart a distance (r r 0 ) σ = NS 0 r r 0 = 1 r 0 2 S 0 r r 0 = S 0 r 0 ε n N = number of bonds/unit area r 0 2 = average area per atom ε n = strain = r r 0 /r 0 Young s modulus is The method of calculating Young s modulus from the stiffnesses of individual bonds E = σ ε n = S 0 r 0 S 0 can be calculated from the theoretically derived U(r) curves 31/34 Table 6.1: Hierarchy of Bond Stiffnesses Bond Type S 0 (N m 1 ) E (GPa); from Equation (with r 0 = 2.5x10 10 m) Covalent, e.g., C C Metallic, e.g., Cu Cu Ionic, e.g., Na Cl H-bond, e.g., H2O H2O Van der Waals, e.g., polymers or metals and ceramics, the values of E we calculate are about right: the bond-stretching idea explains the stiffness of these solids. There exists a whole range of polymers and rubbers that have moduli that are lower by up to a factor of 100 than the lowest we have calculated. Why is this? What determines the moduli of these floppy polymers if it is not the springs between the atoms?

17 All polymers, if really solid, should have moduli above the lowest level we have calculated about 2 GPa since they are held together partly by Van der Waals and partly by covalent bonds. If you take ordinary rubber and cool it down in liquid nitrogen, it becomes stiff its modulus rises rather suddenly from around 10 2 GPa to a proper value of 2 GPa. But if you warm it up again, its modulus drops back to 10 2 GPa The covalent bonds, with occasional cross-links, are very stiff, but they contribute very little to the overall modulus because when you load the structure it is the flabby Van der Waals bonds between the chains that stretch, and it is these that determine the modulus. At low T, rubber has a proper modulus of a few GPa and behaves like a true solid. As rubber warms up above the glass transition temperature, Tg, the Van der Waals bonds melt. Rubber remains solid because of the cross-links, which form a sort of skeleton, but becomes leathery and rubbery. But when you load it, the chains slide over each other in places where there are no cross-linking bonds. This, of course, gives extra strain, and the modulus goes down. Young s modulus increases with increasing density of covalent cross-links in polymers, including rubbers above, Tg. Below T g, the modulus of rubbers increases markedly because the Van der Waals bonds kick in. Above T g they melt, and the modulus drops. Next Class 10 Yield Strength, Tensile Strength and Ductility

12/8/2009. Prof. A.K.M.B. Rashid Department of MME BUET, Dhaka

12/8/2009. Prof. A.K.M.B. Rashid Department of MME BUET, Dhaka Prof. A.K.M.B. Rashid Department of MME BUET, Dhaka Introduction and classes of properties Case studies showing selection of the right material for the job Deformation of material under the action of a

More information

Mechanical properties 1 Elastic behaviour of materials

Mechanical properties 1 Elastic behaviour of materials MME131: Lecture 13 Mechanical properties 1 Elastic behaviour of materials A. K. M. B. Rashid Professor, Department of MME BUET, Dhaka Today s Topics Deformation of material under the action of a mechanical

More information

Introduction to Engineering Materials ENGR2000. Dr. Coates

Introduction to Engineering Materials ENGR2000. Dr. Coates Introduction to Engineering Materials ENGR2 Chapter 6: Mechanical Properties of Metals Dr. Coates 6.2 Concepts of Stress and Strain tension compression shear torsion Tension Tests The specimen is deformed

More information

MATERIALS. Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle?

MATERIALS. Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle? MATERIALS Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle? What is toughness? strength? brittleness? Elemental material atoms: A. Composition

More information

Johns Hopkins University What is Engineering? M. Karweit MATERIALS

Johns Hopkins University What is Engineering? M. Karweit MATERIALS Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle? What is toughness? strength? brittleness? Elemental material atoms: MATERIALS A. Composition

More information

How materials work. Compression Tension Bending Torsion

How materials work. Compression Tension Bending Torsion Materials How materials work Compression Tension Bending Torsion Elemental material atoms: A. Composition a) Nucleus: protons (+), neutrons (0) b) Electrons (-) B. Neutral charge, i.e., # electrons = #

More information

Revision Guide for Chapter 4

Revision Guide for Chapter 4 Revision Guide for Chapter 4 Contents Student s Checklist Revision Notes Materials: properties and uses... 5 Materials selection charts... 5 Refraction... 8 Total internal reflection... 9 Conductors and

More information

NORMAL STRESS. The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts.

NORMAL STRESS. The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts. NORMAL STRESS The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts. σ = force/area = P/A where σ = the normal stress P = the centric

More information

High Tech High Top Hat Technicians. An Introduction to Solid Mechanics. Is that supposed to bend there?

High Tech High Top Hat Technicians. An Introduction to Solid Mechanics. Is that supposed to bend there? High Tech High Top Hat Technicians An Introduction to Solid Mechanics Or Is that supposed to bend there? Why don't we fall through the floor? The power of any Spring is in the same proportion with the

More information

Stress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus. Case study

Stress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus. Case study Stress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus Case study 2 In field of Physics, it explains how an object deforms under an applied force Real rigid bodies are elastic we can

More information

Chapter 7. Highlights:

Chapter 7. Highlights: Chapter 7 Highlights: 1. Understand the basic concepts of engineering stress and strain, yield strength, tensile strength, Young's(elastic) modulus, ductility, toughness, resilience, true stress and true

More information

MECE 3321 MECHANICS OF SOLIDS CHAPTER 3

MECE 3321 MECHANICS OF SOLIDS CHAPTER 3 MECE 3321 MECHANICS OF SOLIDS CHAPTER 3 Samantha Ramirez TENSION AND COMPRESSION TESTS Tension and compression tests are used primarily to determine the relationship between σ avg and ε avg in any material.

More information

ME 2570 MECHANICS OF MATERIALS

ME 2570 MECHANICS OF MATERIALS ME 2570 MECHANICS OF MATERIALS Chapter III. Mechanical Properties of Materials 1 Tension and Compression Test The strength of a material depends on its ability to sustain a load without undue deformation

More information

Solid Mechanics Chapter 1: Tension, Compression and Shear

Solid Mechanics Chapter 1: Tension, Compression and Shear Solid Mechanics Chapter 1: Tension, Compression and Shear Dr. Imran Latif Department of Civil and Environmental Engineering College of Engineering University of Nizwa (UoN) 1 Why do we study Mechanics

More information

6.4 A cylindrical specimen of a titanium alloy having an elastic modulus of 107 GPa ( psi) and

6.4 A cylindrical specimen of a titanium alloy having an elastic modulus of 107 GPa ( psi) and 6.4 A cylindrical specimen of a titanium alloy having an elastic modulus of 107 GPa (15.5 10 6 psi) and an original diameter of 3.8 mm (0.15 in.) will experience only elastic deformation when a tensile

More information

STANDARD SAMPLE. Reduced section " Diameter. Diameter. 2" Gauge length. Radius

STANDARD SAMPLE. Reduced section  Diameter. Diameter. 2 Gauge length. Radius MATERIAL PROPERTIES TENSILE MEASUREMENT F l l 0 A 0 F STANDARD SAMPLE Reduced section 2 " 1 4 0.505" Diameter 3 4 " Diameter 2" Gauge length 3 8 " Radius TYPICAL APPARATUS Load cell Extensometer Specimen

More information

ME 243. Mechanics of Solids

ME 243. Mechanics of Solids ME 243 Mechanics of Solids Lecture 2: Stress and Strain Ahmad Shahedi Shakil Lecturer, Dept. of Mechanical Engg, BUET E-mail: sshakil@me.buet.ac.bd, shakil6791@gmail.com Website: teacher.buet.ac.bd/sshakil

More information

five Mechanics of Materials 1 ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 lecture

five Mechanics of Materials 1 ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 lecture ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 lecture five mechanics www.carttalk.com of materials Mechanics of Materials 1 Mechanics of Materials MECHANICS MATERIALS

More information

Tensile stress strain curves for different materials. Shows in figure below

Tensile stress strain curves for different materials. Shows in figure below Tensile stress strain curves for different materials. Shows in figure below Furthermore, the modulus of elasticity of several materials effected by increasing temperature, as is shown in Figure Asst. Lecturer

More information

Outline. Tensile-Test Specimen and Machine. Stress-Strain Curve. Review of Mechanical Properties. Mechanical Behaviour

Outline. Tensile-Test Specimen and Machine. Stress-Strain Curve. Review of Mechanical Properties. Mechanical Behaviour Tensile-Test Specimen and Machine Review of Mechanical Properties Outline Tensile test True stress - true strain (flow curve) mechanical properties: - Resilience - Ductility - Toughness - Hardness A standard

More information

The science of elasticity

The science of elasticity The science of elasticity In 1676 Hooke realized that 1.Every kind of solid changes shape when a mechanical force acts on it. 2.It is this change of shape which enables the solid to supply the reaction

More information

Statics Principles. The laws of motion describe the interaction of forces acting on a body. Newton s First Law of Motion (law of inertia):

Statics Principles. The laws of motion describe the interaction of forces acting on a body. Newton s First Law of Motion (law of inertia): Unit 2 Review Statics Statics Principles The laws of motion describe the interaction of forces acting on a body Newton s First Law of Motion (law of inertia): An object in a state of rest or uniform motion

More information

9 MECHANICAL PROPERTIES OF SOLIDS

9 MECHANICAL PROPERTIES OF SOLIDS 9 MECHANICAL PROPERTIES OF SOLIDS Deforming force Deforming force is the force which changes the shape or size of a body. Restoring force Restoring force is the internal force developed inside the body

More information

Structure-Property Correlation [2] Atomic bonding and material properties

Structure-Property Correlation [2] Atomic bonding and material properties MME 297: Lecture 05 Structure-Property Correlation [2] Atomic bonding and material properties Dr. A. K. M. Bazlur Rashid Professor, Department of MME BUET, Dhaka Topics to discuss today... Review of atomic

More information

CPO Science Foundations of Physics. Unit 8, Chapter 27

CPO Science Foundations of Physics. Unit 8, Chapter 27 CPO Science Foundations of Physics Unit 8, Chapter 27 Unit 8: Matter and Energy Chapter 27 The Physical Properties of Matter 27.1 Properties of Solids 27.2 Properties of Liquids and Fluids 27.3 Properties

More information

[5] Stress and Strain

[5] Stress and Strain [5] Stress and Strain Page 1 of 34 [5] Stress and Strain [5.1] Internal Stress of Solids [5.2] Design of Simple Connections (will not be covered in class) [5.3] Deformation and Strain [5.4] Hooke s Law

More information

Mechanics of Materials

Mechanics of Materials Mechanics of Materials Notation: a = acceleration = area (net = with holes, bearing = in contact, etc...) SD = allowable stress design d = diameter of a hole = calculus symbol for differentiation e = change

More information

Stress-Strain Behavior

Stress-Strain Behavior Stress-Strain Behavior 6.3 A specimen of aluminum having a rectangular cross section 10 mm 1.7 mm (0.4 in. 0.5 in.) is pulled in tension with 35,500 N (8000 lb f ) force, producing only elastic deformation.

More information

EDEXCEL NATIONAL CERTIFICATE/DIPLOMA MECHANICAL PRINCIPLES AND APPLICATIONS NQF LEVEL 3 OUTCOME 1 - LOADING SYSTEMS TUTORIAL 3 LOADED COMPONENTS

EDEXCEL NATIONAL CERTIFICATE/DIPLOMA MECHANICAL PRINCIPLES AND APPLICATIONS NQF LEVEL 3 OUTCOME 1 - LOADING SYSTEMS TUTORIAL 3 LOADED COMPONENTS EDEXCEL NATIONAL CERTIICATE/DIPLOMA MECHANICAL PRINCIPLES AND APPLICATIONS NQ LEVEL 3 OUTCOME 1 - LOADING SYSTEMS TUTORIAL 3 LOADED COMPONENTS 1. Be able to determine the effects of loading in static engineering

More information

Chapter 6: Mechanical Properties of Metals. Dr. Feras Fraige

Chapter 6: Mechanical Properties of Metals. Dr. Feras Fraige Chapter 6: Mechanical Properties of Metals Dr. Feras Fraige Stress and Strain Tension Compression Shear Torsion Elastic deformation Plastic Deformation Yield Strength Tensile Strength Ductility Toughness

More information

Theory at a Glance (for IES, GATE, PSU)

Theory at a Glance (for IES, GATE, PSU) 1. Stress and Strain Theory at a Glance (for IES, GATE, PSU) 1.1 Stress () When a material is subjected to an external force, a resisting force is set up within the component. The internal resistance force

More information

4.MECHANICAL PROPERTIES OF MATERIALS

4.MECHANICAL PROPERTIES OF MATERIALS 4.MECHANICAL PROPERTIES OF MATERIALS The diagram representing the relation between stress and strain in a given material is an important characteristic of the material. To obtain the stress-strain diagram

More information

MECHANICAL PROPERTIES OF SOLIDS

MECHANICAL PROPERTIES OF SOLIDS INTRODUCTION A rigid body generally means a hard solid object having a definite shape and size. But in reality, bodies can be stretched, compressed and bent. Even the appreciably rigid steel bar can be

More information

Physical Properties Testing Technical Bulletin

Physical Properties Testing Technical Bulletin Technical Bulletin MANUFACTURER Raven Lining Systems 13105 E. 61 st Street, Suite A Broken Arrow, OK 74012 (918) 615-0020 TENSILE TESTING OF PLASTICS ASTM D638, ISO 527 Tensile tests measure the force

More information

EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 2 Stress & Strain - Axial Loading

EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 2 Stress & Strain - Axial Loading MA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 2 Stress & Strain - Axial Loading MA 3702 Mechanics & Materials Science Zhe Cheng (2018) 2 Stress & Strain - Axial Loading Statics

More information

UNIVERSITY PHYSICS I. Professor Meade Brooks, Collin College. Chapter 12: STATIC EQUILIBRIUM AND ELASTICITY

UNIVERSITY PHYSICS I. Professor Meade Brooks, Collin College. Chapter 12: STATIC EQUILIBRIUM AND ELASTICITY UNIVERSITY PHYSICS I Professor Meade Brooks, Collin College Chapter 12: STATIC EQUILIBRIUM AND ELASTICITY Two stilt walkers in standing position. All forces acting on each stilt walker balance out; neither

More information

Chapter 13 ELASTIC PROPERTIES OF MATERIALS

Chapter 13 ELASTIC PROPERTIES OF MATERIALS Physics Including Human Applications 280 Chapter 13 ELASTIC PROPERTIES OF MATERIALS GOALS When you have mastered the contents of this chapter, you will be able to achieve the following goals: Definitions

More information

Elastic Properties of Solid Materials. Notes based on those by James Irvine at

Elastic Properties of Solid Materials. Notes based on those by James Irvine at Elastic Properties of Solid Materials Notes based on those by James Irvine at www.antonine-education.co.uk Key Words Density, Elastic, Plastic, Stress, Strain, Young modulus We study how materials behave

More information

Samantha Ramirez, MSE. Stress. The intensity of the internal force acting on a specific plane (area) passing through a point. F 2

Samantha Ramirez, MSE. Stress. The intensity of the internal force acting on a specific plane (area) passing through a point. F 2 Samantha Ramirez, MSE Stress The intensity of the internal force acting on a specific plane (area) passing through a point. Δ ΔA Δ z Δ 1 2 ΔA Δ x Δ y ΔA is an infinitesimal size area with a uniform force

More information

There are three main types of structure - mass, framed and shells.

There are three main types of structure - mass, framed and shells. STRUCTURES There are three main types of structure - mass, framed and shells. Mass structures perform due to their own weight. An example would be a dam. Frame structures resist loads due to the arrangement

More information

Agricultural Science 1B Principles & Processes in Agriculture. Mike Wheatland

Agricultural Science 1B Principles & Processes in Agriculture. Mike Wheatland Agricultural Science 1B Principles & Processes in Agriculture Mike Wheatland (m.wheatland@physics.usyd.edu.au) Outline - Lectures weeks 9-12 Chapter 6: Balance in nature - description of energy balance

More information

1. A pure shear deformation is shown. The volume is unchanged. What is the strain tensor.

1. A pure shear deformation is shown. The volume is unchanged. What is the strain tensor. Elasticity Homework Problems 2014 Section 1. The Strain Tensor. 1. A pure shear deformation is shown. The volume is unchanged. What is the strain tensor. 2. Given a steel bar compressed with a deformation

More information

MECHANICAL PROPERTIES OF SOLIDS

MECHANICAL PROPERTIES OF SOLIDS Chapter Nine MECHANICAL PROPERTIES OF SOLIDS MCQ I 9.1 Modulus of rigidity of ideal liquids is (a) infinity. (b) zero. (c) unity. (d) some finite small non-zero constant value. 9. The maximum load a wire

More information

BioMechanics and BioMaterials Lab (BME 541) Experiment #5 Mechanical Prosperities of Biomaterials Tensile Test

BioMechanics and BioMaterials Lab (BME 541) Experiment #5 Mechanical Prosperities of Biomaterials Tensile Test BioMechanics and BioMaterials Lab (BME 541) Experiment #5 Mechanical Prosperities of Biomaterials Tensile Test Objectives 1. To be familiar with the material testing machine(810le4) and provide a practical

More information

Mechanical Properties of Materials

Mechanical Properties of Materials Mechanical Properties of Materials Strains Material Model Stresses Learning objectives Understand the qualitative and quantitative description of mechanical properties of materials. Learn the logic of

More information

Lecture No. (1) Introduction of Polymers

Lecture No. (1) Introduction of Polymers Lecture No. (1) Introduction of Polymers Polymer Structure Polymers are found in nature as proteins, cellulose, silk or synthesized like polyethylene, polystyrene and nylon. Some natural polymers can also

More information

, to obtain a way to calculate stress from the energy function U(r).

, to obtain a way to calculate stress from the energy function U(r). BIOEN 36 014 LECTURE : MOLECULAR BASIS OF ELASTICITY Estimating Young s Modulus from Bond Energies and Structures First we consider solids, which include mostly nonbiological materials, such as metals,

More information

2/28/2006 Statics ( F.Robilliard) 1

2/28/2006 Statics ( F.Robilliard) 1 2/28/2006 Statics (.Robilliard) 1 Extended Bodies: In our discussion so far, we have considered essentially only point masses, under the action of forces. We now broaden our considerations to extended

More information

MECHANICS OF MATERIALS. Prepared by Engr. John Paul Timola

MECHANICS OF MATERIALS. Prepared by Engr. John Paul Timola MECHANICS OF MATERIALS Prepared by Engr. John Paul Timola Mechanics of materials branch of mechanics that studies the internal effects of stress and strain in a solid body. stress is associated with the

More information

Mechanical Properties

Mechanical Properties Mechanical Properties Elastic deformation Plastic deformation Fracture I. Elastic Deformation S s u s y e u e T I II III e For a typical ductile metal: I. Elastic deformation II. Stable plastic deformation

More information

Mechanics of Solids. Mechanics Of Solids. Suraj kr. Ray Department of Civil Engineering

Mechanics of Solids. Mechanics Of Solids. Suraj kr. Ray Department of Civil Engineering Mechanics Of Solids Suraj kr. Ray (surajjj2445@gmail.com) Department of Civil Engineering 1 Mechanics of Solids is a branch of applied mechanics that deals with the behaviour of solid bodies subjected

More information

Module-4. Mechanical Properties of Metals

Module-4. Mechanical Properties of Metals Module-4 Mechanical Properties of Metals Contents ) Elastic deformation and Plastic deformation ) Interpretation of tensile stress-strain curves 3) Yielding under multi-axial stress, Yield criteria, Macroscopic

More information

MECHANICS OF MATERIALS

MECHANICS OF MATERIALS CHATR Stress MCHANICS OF MATRIALS and Strain Axial Loading Stress & Strain: Axial Loading Suitability of a structure or machine may depend on the deformations in the structure as well as the stresses induced

More information

UNIT I SIMPLE STRESSES AND STRAINS

UNIT I SIMPLE STRESSES AND STRAINS Subject with Code : SM-1(15A01303) Year & Sem: II-B.Tech & I-Sem SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (DESCRIPTIVE) UNIT I SIMPLE STRESSES

More information

QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS

QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State Hooke s law. 3. Define modular ratio,

More information

Strength of Materials (15CV 32)

Strength of Materials (15CV 32) Strength of Materials (15CV 32) Module 1 : Simple Stresses and Strains Dr. H. Ananthan, Professor, VVIET,MYSURU 8/21/2017 Introduction, Definition and concept and of stress and strain. Hooke s law, Stress-Strain

More information

Geology 2112 Principles and Applications of Geophysical Methods WEEK 1. Lecture Notes Week 1

Geology 2112 Principles and Applications of Geophysical Methods WEEK 1. Lecture Notes Week 1 Lecture Notes Week 1 A Review of the basic properties and mechanics of materials Suggested Reading: Relevant sections from any basic physics or engineering text. Objectives: Review some basic properties

More information

QUESTION BANK DEPARTMENT: CIVIL SEMESTER: III SUBJECT CODE: CE2201 SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A

QUESTION BANK DEPARTMENT: CIVIL SEMESTER: III SUBJECT CODE: CE2201 SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A DEPARTMENT: CIVIL SUBJECT CODE: CE2201 QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State

More information

ME 207 Material Science I

ME 207 Material Science I ME 207 Material Science I Chapter 3 Properties in Tension and Compression Dr. İbrahim H. Yılmaz http://web.adanabtu.edu.tr/iyilmaz Automotive Engineering Adana Science and Technology University Introduction

More information

Lecture 8 Viscoelasticity and Deformation

Lecture 8 Viscoelasticity and Deformation Read: pg 130 168 (rest of Chpt. 4) 1 Poisson s Ratio, µ (pg. 115) Ratio of the strain in the direction perpendicular to the applied force to the strain in the direction of the applied force. For uniaxial

More information

EDEXCEL NATIONAL CERTIFICATE/DIPLOMA SCIENCE FOR TECHNICIANS OUTCOME 1 - STATIC AND DYNAMIC FORCES TUTORIAL 3 STRESS AND STRAIN

EDEXCEL NATIONAL CERTIFICATE/DIPLOMA SCIENCE FOR TECHNICIANS OUTCOME 1 - STATIC AND DYNAMIC FORCES TUTORIAL 3 STRESS AND STRAIN EDEXCEL NATIONAL CERTIFICATE/DIPLOMA SCIENCE FOR TECHNICIANS OUTCOME 1 - STATIC AND DYNAMIC FORCES TUTORIAL 3 STRESS AND STRAIN 1 Static and dynamic forces Forces: definitions of: matter, mass, weight,

More information

AERO 214. Lab II. Measurement of elastic moduli using bending of beams and torsion of bars

AERO 214. Lab II. Measurement of elastic moduli using bending of beams and torsion of bars AERO 214 Lab II. Measurement of elastic moduli using bending of beams and torsion of bars BENDING EXPERIMENT Introduction Flexural properties of materials are of interest to engineers in many different

More information

Mechanical Properties of Polymers. Scope. MSE 383, Unit 3-1. Joshua U. Otaigbe Iowa State University Materials Science & Engineering Dept.

Mechanical Properties of Polymers. Scope. MSE 383, Unit 3-1. Joshua U. Otaigbe Iowa State University Materials Science & Engineering Dept. Mechanical Properties of Polymers Scope MSE 383, Unit 3-1 Joshua U. Otaigbe Iowa State University Materials Science & Engineering Dept. Structure - mechanical properties relations Time-dependent mechanical

More information

MECHANICAL AND RHEOLOGICAL PROPERTIES

MECHANICAL AND RHEOLOGICAL PROPERTIES MECHANICAL AND RHEOLOGICAL PROPERTIES MECHANICAL PROPERTIES OF SOLIDS Extension Shear δ τ xy l 0 l l 0 θ σ Hooke's law σ = Eε Hooke's law τ = G γ xy xy MECHANICAL AND RHEOLOGICAL PROPERTIES RHEOLOGICAL

More information

Advanced Strength of Materials Prof S. K. Maiti Mechanical Engineering Indian Institute of Technology, Bombay. Lecture 27

Advanced Strength of Materials Prof S. K. Maiti Mechanical Engineering Indian Institute of Technology, Bombay. Lecture 27 Advanced Strength of Materials Prof S. K. Maiti Mechanical Engineering Indian Institute of Technology, Bombay Lecture 27 Last time we considered Griffith theory of brittle fracture, where in it was considered

More information

Materials: engineering, science, processing and design, 2nd edition Copyright (c)2010 Michael Ashby, Hugh Shercliff, David Cebon.

Materials: engineering, science, processing and design, 2nd edition Copyright (c)2010 Michael Ashby, Hugh Shercliff, David Cebon. Modes of Loading (1) tension (a) (2) compression (b) (3) bending (c) (4) torsion (d) and combinations of them (e) Figure 4.2 1 Standard Solution to Elastic Problems Three common modes of loading: (a) tie

More information

22 Which of the following correctly defines the terms stress, strain and Young modulus? stress strain Young modulus

22 Which of the following correctly defines the terms stress, strain and Young modulus? stress strain Young modulus PhysicsndMathsTutor.com Which of the following correctly defines the terms stress, strain and Young modulus? 97/1/M/J/ stress strain Young modulus () x (area) (extension) x (original length) (stress) /

More information

Chapter 26 Elastic Properties of Materials

Chapter 26 Elastic Properties of Materials Chapter 26 Elastic Properties of Materials 26.1 Introduction... 1 26.2 Stress and Strain in Tension and Compression... 2 26.3 Shear Stress and Strain... 4 Example 26.1: Stretched wire... 5 26.4 Elastic

More information

STRESS, STRAIN AND DEFORMATION OF SOLIDS

STRESS, STRAIN AND DEFORMATION OF SOLIDS VELAMMAL COLLEGE OF ENGINEERING AND TECHNOLOGY, MADURAI 625009 DEPARTMENT OF CIVIL ENGINEERING CE8301 STRENGTH OF MATERIALS I -------------------------------------------------------------------------------------------------------------------------------

More information

Mechanics of Materials Primer

Mechanics of Materials Primer Mechanics of Materials rimer Notation: A = area (net = with holes, bearing = in contact, etc...) b = total width of material at a horizontal section d = diameter of a hole D = symbol for diameter E = modulus

More information

Medical Biomaterials Prof. Mukesh Doble Department of Biotechnology Indian Institute of Technology, Madras. Lecture - 04 Properties (Mechanical)

Medical Biomaterials Prof. Mukesh Doble Department of Biotechnology Indian Institute of Technology, Madras. Lecture - 04 Properties (Mechanical) Medical Biomaterials Prof. Mukesh Doble Department of Biotechnology Indian Institute of Technology, Madras Lecture - 04 Properties (Mechanical) Welcome to the course on medical biomaterials. Today we are

More information

MAAE 2202 A. Come to the PASS workshop with your mock exam complete. During the workshop you can work with other students to review your work.

MAAE 2202 A. Come to the PASS workshop with your mock exam complete. During the workshop you can work with other students to review your work. It is most beneficial to you to write this mock final exam UNDER EXAM CONDITIONS. This means: Complete the exam in 3 hours. Work on your own. Keep your textbook closed. Attempt every question. After the

More information

INTRODUCTION (Cont..)

INTRODUCTION (Cont..) INTRODUCTION Name : Mohamad Redhwan Abd Aziz Post : Lecturer @ DEAN CENTER OF HND STUDIES Subject : Solid Mechanics Code : BME 2033 Room : CENTER OF HND STUDIES OFFICE H/P No. : 019-2579663 W/SITE : Http://tatiuc.edu.my/redhwan

More information

Contents of The Universe and Deforming Solids

Contents of The Universe and Deforming Solids Skyscrapers in the 2011 Japan Earthquake Contents of The Universe and Deforming Solids For most of this course, we ve talked about physics we ve known about for > 100 years. Today, we ll discuss some physics

More information

Class XI Physics. Ch. 9: Mechanical Properties of solids. NCERT Solutions

Class XI Physics. Ch. 9: Mechanical Properties of solids. NCERT Solutions Downloaded from Class XI Physics Ch. 9: Mechanical Properties of solids NCERT Solutions Page 242 Question 9.1: A steel wire of length 4.7 m and cross-sectional area 3.0 10 5 m 2 stretches by the same amount

More information

MECHANICS OF MATERIALS

MECHANICS OF MATERIALS Third E CHAPTER 2 Stress MECHANICS OF MATERIALS Ferdinand P. Beer E. Russell Johnston, Jr. John T. DeWolf Lecture Notes: J. Walt Oler Texas Tech University and Strain Axial Loading Contents Stress & Strain:

More information

Elasticity. A PowerPoint Presentation by Paul E. Tippens, Professor of Physics Southern Polytechnic State University Modified by M.

Elasticity. A PowerPoint Presentation by Paul E. Tippens, Professor of Physics Southern Polytechnic State University Modified by M. Elasticity A PowerPoint Presentation by Paul E. Tippens, Professor of Physics Southern Polytechnic State University Modified by M. Lepore Elasticity Photo Vol. 10 PhotoDisk/Getty BUNGEE jumping utilizes

More information

Strain Measurement. Prof. Yu Qiao. Department of Structural Engineering, UCSD. Strain Measurement

Strain Measurement. Prof. Yu Qiao. Department of Structural Engineering, UCSD. Strain Measurement Strain Measurement Prof. Yu Qiao Department of Structural Engineering, UCSD Strain Measurement The design of load-carrying components for machines and structures requires information about the distribution

More information

Strength of Material. Shear Strain. Dr. Attaullah Shah

Strength of Material. Shear Strain. Dr. Attaullah Shah Strength of Material Shear Strain Dr. Attaullah Shah Shear Strain TRIAXIAL DEFORMATION Poisson's Ratio Relationship Between E, G, and ν BIAXIAL DEFORMATION Bulk Modulus of Elasticity or Modulus of Volume

More information

13 Solid materials Exam practice questions

13 Solid materials Exam practice questions Pages 206-209 Exam practice questions 1 a) The toughest material has the largest area beneath the curve the answer is C. b) The strongest material has the greatest breaking stress the answer is B. c) A

More information

Equilibrium. the linear momentum,, of the center of mass is constant

Equilibrium. the linear momentum,, of the center of mass is constant Equilibrium is the state of an object where: Equilibrium the linear momentum,, of the center of mass is constant Feb. 19, 2018 the angular momentum,, about the its center of mass, or any other point, is

More information

(Refer Slide Time: 00:58)

(Refer Slide Time: 00:58) Nature and Properties of Materials Professor Bishak Bhattacharya Department of Mechanical Engineering Indian Institute of Technology Kanpur Lecture 18 Effect and Glass Transition Temperature In the last

More information

Flexural properties of polymers

Flexural properties of polymers A2 _EN BUDAPEST UNIVERSITY OF TECHNOLOGY AND ECONOMICS FACULTY OF MECHANICAL ENGINEERING DEPARTMENT OF POLYMER ENGINEERING Flexural properties of polymers BENDING TEST OF CHECK THE VALIDITY OF NOTE ON

More information

Structural Metals Lab 1.2. Torsion Testing of Structural Metals. Standards ASTM E143: Shear Modulus at Room Temperature

Structural Metals Lab 1.2. Torsion Testing of Structural Metals. Standards ASTM E143: Shear Modulus at Room Temperature Torsion Testing of Structural Metals Standards ASTM E143: Shear Modulus at Room Temperature Purpose To determine the shear modulus of structural metals Equipment Tinius-Olsen Lo-Torq Torsion Machine (figure

More information

N = N A Pb A Pb. = ln N Q v kt. = kt ln v N

N = N A Pb A Pb. = ln N Q v kt. = kt ln v N 5. Calculate the energy for vacancy formation in silver, given that the equilibrium number of vacancies at 800 C (1073 K) is 3.6 10 3 m 3. The atomic weight and density (at 800 C) for silver are, respectively,

More information

CHAPTER 3 THE EFFECTS OF FORCES ON MATERIALS

CHAPTER 3 THE EFFECTS OF FORCES ON MATERIALS CHAPTER THE EFFECTS OF FORCES ON MATERIALS EXERCISE 1, Page 50 1. A rectangular bar having a cross-sectional area of 80 mm has a tensile force of 0 kn applied to it. Determine the stress in the bar. Stress

More information

A concrete cylinder having a a diameter of of in. mm and elasticity. Stress and Strain: Stress and Strain: 0.

A concrete cylinder having a a diameter of of in. mm and elasticity. Stress and Strain: Stress and Strain: 0. 2011 earson Education, Inc., Upper Saddle River, NJ. ll rights reserved. This material is protected under all copyright laws as they currently 8 1. 3 1. concrete cylinder having a a diameter of of 6.00

More information

Chapter 2. Atomic Structure

Chapter 2. Atomic Structure Chapter 2 Atomic Structure 2 6 (a) Aluminum foil used for storing food weighs about 0. g per square cm. How many atoms of aluminum are contained in one 6.25 cm 2 size of foil? (b) Using the densities and

More information

cos(θ)sin(θ) Alternative Exercise Correct Correct θ = 0 skiladæmi 10 Part A Part B Part C Due: 11:59pm on Wednesday, November 11, 2015

cos(θ)sin(θ) Alternative Exercise Correct Correct θ = 0 skiladæmi 10 Part A Part B Part C Due: 11:59pm on Wednesday, November 11, 2015 skiladæmi 10 Due: 11:59pm on Wednesday, November 11, 015 You will receive no credit for items you complete after the assignment is due Grading Policy Alternative Exercise 1115 A bar with cross sectional

More information

Geology 229 Engineering Geology. Lecture 5. Engineering Properties of Rocks (West, Ch. 6)

Geology 229 Engineering Geology. Lecture 5. Engineering Properties of Rocks (West, Ch. 6) Geology 229 Engineering Geology Lecture 5 Engineering Properties of Rocks (West, Ch. 6) Common mechanic properties: Density; Elastic properties: - elastic modulii Outline of this Lecture 1. Uniaxial rock

More information

TENSILE TESTS (ASTM D 638, ISO

TENSILE TESTS (ASTM D 638, ISO MODULE 4 The mechanical properties, among all the properties of plastic materials, are often the most important properties because virtually all service conditions and the majority of end-use applications

More information

2.2 - Screening and ranking for optimal selection. Outline

2.2 - Screening and ranking for optimal selection. Outline 2 - Ashby Method 2.2 - Screening and ranking for optimal selection Outline Basic steps of selection 1. Translation of design requirements into a material specification 2. Screening out of materials that

More information

ENG1001 Engineering Design 1

ENG1001 Engineering Design 1 ENG1001 Engineering Design 1 Structure & Loads Determine forces that act on structures causing it to deform, bend, and stretch Forces push/pull on objects Structures are loaded by: > Dead loads permanent

More information

Constitutive Equations (Linear Elasticity)

Constitutive Equations (Linear Elasticity) Constitutive quations (Linear lasticity) quations that characterize the physical properties of the material of a system are called constitutive equations. It is possible to find the applied stresses knowing

More information

Technical Note PP TN Engineering Considerations for Temperature Change

Technical Note PP TN Engineering Considerations for Temperature Change Technical Note PP 814 - TN Engineering Considerations for Temperature Change www.performancepipe.com Like most materials, polyethylene is affected by temperature change. However, polyethylene s response

More information

5. STRESS CONCENTRATIONS. and strains in shafts apply only to solid and hollow circular shafts while they are in the

5. STRESS CONCENTRATIONS. and strains in shafts apply only to solid and hollow circular shafts while they are in the 5. STRESS CONCENTRATIONS So far in this thesis, most of the formulas we have seen to calculate the stresses and strains in shafts apply only to solid and hollow circular shafts while they are in the elastic

More information

The objective of this experiment is to investigate the behavior of steel specimen under a tensile test and to determine it's properties.

The objective of this experiment is to investigate the behavior of steel specimen under a tensile test and to determine it's properties. Objective: The objective of this experiment is to investigate the behavior of steel specimen under a tensile test and to determine it's properties. Introduction: Mechanical testing plays an important role

More information

MECHANICAL PROPERTIES OF MATERIALS

MECHANICAL PROPERTIES OF MATERIALS 1 MECHANICAL PROPERTIES OF MATERIALS Pressure in Solids: Pressure in Liquids: Pressure = force area (P = F A ) 1 Pressure = height density gravity (P = hρg) 2 Deriving Pressure in a Liquid Recall that:

More information

INTRODUCTION TO STRAIN

INTRODUCTION TO STRAIN SIMPLE STRAIN INTRODUCTION TO STRAIN In general terms, Strain is a geometric quantity that measures the deformation of a body. There are two types of strain: normal strain: characterizes dimensional changes,

More information

Science 7 Unit B: Structures and Forces. Topic 4. Forces, Loads, & Stresses. pp WORKBOOK. Name:

Science 7 Unit B: Structures and Forces. Topic 4. Forces, Loads, & Stresses. pp WORKBOOK. Name: Science 7 Unit B: Structures and Forces Topic 4 Forces, Loads, & Stresses pp. 305-314 WORKBOOK Name: Every object that provides support is a structure. A structure may be made up of one or more parts,

More information