400 Volts, 50HZ 480 Volts, 60HZ 600 Volts, 60HZ TECHNICAL REFERENCE MANUAL

Transcription

1 400 Volts, 50HZ 480 Volts, 60HZ 600 Volts, 60HZ TECHNICAL REFERENCE MANUAL FORM: MAP-TRM-E REL. July 2013 REV MTE Corporation

2 IMPORTANT USER INFORMATION NOTICE The MTE Corporation Matrix AP Harmonic Filter is designed for harmonic mitigation of 6-pulse inverter drives supplying variable torque loads in a wide variety of applications. The suitability of this filter for a specific application must therefore be determined by the customer. In no event will MTE Corporation assume responsibility or liability for any direct or consequential damages resulting from the use or application of this filter. Nor will MTE Corporation assume patent liability with respect to the use of information, circuits or equipment described in this instruction manual. The Matrix AP Harmonic Filter uses a patent pending Adaptive Passive Harmonic Mitigating Reactor (AP HMR) technology to limit full load current distortion to less than 5% THID and 8% at 30% load. MAPP0320D 1

3 TABLE OF CONTENTS IMPORTANT USER INFORMATION...1 TABLE OF CONTENTS...2 SELECTION GUIDE LINES...4 PART NUMBER CODES...5 MATRIX AP SPECIFICATIONS:...6 AGENCY APPROVALS... 6 PERFORMANCE... 6 ENCLOSURES... 7 WARRANTY...7 OVER TEMPERATURE SWITCH RATINGS...8 TYPICAL PERFORMANCE DATA...9 LOAD EFFECT ON THID... 9 TYPICAL HARMONIC SPECTRUM WITH AND WITHOUT... 9 MATRIX AP HARMONIC FILTER... 9 POWER FACTOR... 9 PERFORMANCE WITH UNBALANCED LINE VOLTAGE (TYPICAL) ALTITUDE DE-RATING CURVE TEMPERATURE DE-RATING CURVE VOLTAGE DISTORTION DE-RATING CURVE MATRIX AP 400 VOLTS, 50HZ SELECTION TABLES OPEN PANEL & GENERAL PURPOSE NEMA 1/ NEMA 3R Enclosures RATINGS Watts loss REGULATION TABLE CAPACITOR CURRENTS OPEN STYLE SIZE AND WEIGHTS ENCLOSED UNIT SIZE AND WEIGHTS MOUNTING PATTERNS AP HMR Bolt Hole Mounting Patterns Capacitor and Cap-panel Bolt Hole Mounting Patterns MATRIX AP 480 VOLTS, 60HZ SELECTION TABLES OPEN PANEL & GENERAL PURPOSE NEMA 1/ NEMA 3R Enclosures RATINGS Watts loss REGULATION TABLE CAPACITOR CURRENTS OPEN STYLE SIZE AND WEIGHTS ENCLOSED UNIT SIZE AND WEIGHTS MOUNTING PATTERNS AP HMR Bolt Hole Mounting Patterns Capacitor and Cap-panel Bolt Hole Mounting Patterns

4 MATRIX AP 600 VOLTS, 60HZ SELECTION TABLES OPEN PANEL & GENERAL PURPOSE NEMA 1/ NEMA 3R Enclosures RATINGS Watts loss REGULATION TABLE CAPACITOR CURRENTS OPEN STYLE SIZE AND WEIGHTS ENCLOSED UNIT SIZE AND WEIGHTS MOUNTING PATTERNS AP HMR Bolt Hole Mounting Patterns Capacitor and Cap-panel Bolt Hole Mounting Patterns AP HMR MOUNTING & TERMINAL LOCATIONS AP HMR 6 44 Amp (400V & 480V) AP HMR 6 34 Amp (600V) AP HMR 103 Amp (400V & 480V) AP HMR Amp (600V) AP HMR Amp (400V & 480V) AP HMR Amp (600V) AP HMR Amp (400V & 480V) AP HMR Amp (600V) AP HMR Amp (400V & 480V) AP HMR Amp (600V) CAP-ASSEMBLY MOUNTING & TERMINAL LOCATIONS Three Phase Capacitor High Current Capacitor Panel ENCLOSED UNIT INTERNAL DETAILS CAB-12AP CAB-17AP CAB-26AP CAB-26APD... CAB-42AP CAB-48AP OPEN PANEL UNIT INTERCONNECTION DIAGRAM ENCLOSED UNIT INTERCONNECTION DIAGRAM MATRIX AP BASIC SCHEMATIC DIAGRAM CONTACTOR OPTIONS CONTACTOR COIL SWITCHING CURRENTS

5 Selection Guide Lines The Matrix AP harmonic filter uses patented Harmonics Mitigating Reactor (HMR) technology to limit full load current distortion to less than 5% THID. Filters for variable torque AC drives rated 7.5 Hp and above should be selected for a filter output current rating greater than or equal to the motor current rating. If the motor current rating is not available, use the NEC motor current rating. Filters for variable torque AC drives rated 2 5 Hp should be selected for a filter output current rating greater than or equal to 105% of the motor current rating. If the motor current rating is not available, select on the basis of 105% of the NEC motor current rating. Filters for variable torque AC drives rated less than 1.5 Hp should be selected for an output current rating greater than or equal to 110% of the motor current rating or 110% of the NEC motor current rating. For constant torque, determine the maximum current through the filter and size accordingly. For phase controlled DC drive applications, select filter current rating per application note Matrix Filter with Phase Controlled DC Driver. Where a single filter is used to feed multiple drives, the output current rating of the filter should be selected to equal the total current rating plus 10% of the individual drives when calculated according to the instructions above. Note: THID may exceed 5% at light loading; see Figure 1 for the THID performance details. This document incorporates advance search and view features compatible with Adobe Acrobat 4 and above PDF reader software. 4

6 PART NUMBER CODES Matrix Series AP MAP X X _ TYPE P Panel mounts G General Purpose NEMA 2 W Weather NEMA 3R CURRENT RATING 0006 is 6 Amps 0083 is 83 Amps 1200 is 1200 Amps VOLTAGE FREQUENCY CODE C 400 Volts, 50 Hz D 480 Volts, 60 Hz E 600 Volts, 60 Hz CONTACTOR OPTIONS 002 Contactor for capacitor disconnect 009 Contactor with adjustable pick up and drop out 012 Contactor with control transformer ENCLOSURE OPTION Option -400** Standard NEMA 3R enclosure with optional rodent / serpent screen Option 400 provides intake exhaust air screens with (¼ X ¼) mesh openings. Change above listed catalog number from MAPWxxxxx to MAPWxxxx400 and add $ to the list price. ** Note: Call factory for availability. Option may result in extended lead times. 5

7 Matrix AP Specifications: Generator sizing note: Generator sizing is best completed by sizing programs or help from a generator manufacturing representative. Identify every load type and size that will be powered from the generator. If non-linear loads are present the generator may need to be oversized. Generator rated KVA minimum load >= Matrix rated current x 3 generator voltage FLA load current <= Matrix filter rated current Service Conditions Load: 6-pulse variable torque rectifier only Input voltage(s): 480V Version (PN# s MAPxxxxxD) VAC +/- 10%, Hz, 3 phase 400V Version (PN# s MAPxxxxxC) VAC +/- 10% Hz. 3 phase 600V Version (PN# s MAPxxxxxE) VAC +/- 10% Hz. 3 phase Input voltage line unbalance: 1% maximum to ensure performance guarantee. Maximum source impedance: 6.00% to ensure performance guarantee. Matrix AP works with Gensets that have source impedance of ~ 15% Minimum source impedance: 1.5% Service Factor: 1.00 Overload: 150% for 1 minute duration with 10% output voltage reduction of nominal of voltage. Ambient Temperature (Operating): Refer to figure 5 for temperature de-rating. Enclosed Filters: Open Panel Filters: Storage Temperature: 320A and above: -40 to +45 degrees C Below 320A: -40 to +40 degrees C -40 to +50 degrees C -40 to +90 degrees C Altitude: 0 to 3300 Feet above sea level. Refer to figure 4 for altitude de-rating. Relative Humidity: 0 to 95% non-condensing Over Voltage: Category II Agency Approvals Notes (SCCR): UL and cul listed to UL508 Type MX and CSA-C22.2 No File E ( HP, 120VAC through 600VAC 50, 50/60, 60 Hz Three Phase) CE Marked, 400VAC 50 Hz The Short Circuit Current Rating (SCCR) is not required under Exception No.1 of UL508A SB4.2.1 effective 4/25/06. This exception also applies to all the Contactor Options (002, 009, 012, and similar), where the Contactors are separated from the Main Power path by exempt components (such as Reactors) of sufficient Impedance, which is assured in case of the Reactors that are integral components of our Filter. Performance Total Harmonic Current Distortion: 8% MAX at 30% load, 5% MAX at FULL LOAD 6

8 Enclosures MTE enclosures are designed to provide a degree of protection for electrical components and prevent incidental personnel contact with the enclosed equipment. Depending on the enclosure selected, these enclosures meet the requirements of NEMA 1, 2 or 3R. An approximate cross reference guide between NEMA, UL, CSA and IEC enclosure follows. Type 1 NEMA / IEC IP20 enclosure: Are designed for indoor use and will provide protection against contact with the enclosed equipment. Type 2 NEMA / IEC IP20 enclosure: Are designed for indoor use and will provide protection against contact with the enclosed equipment and provide a degree of protection against limited amounts of falling water and dirt. Type 3R NEMA / IEC IP21 enclosure: Are designed for outdoor use primarily to provide protection against contact with the enclosed equipment and provide a degree of protection against falling rain, sleet and external ice formation. Warranty Three years from the date of shipment. 7

9 Over Temperature Switch Ratings Table 1 NC Switch opens at 180 Deg. +/- 5 deg C Current Amps Voltage Contact Load AC Resistive Loads AC Inductive Loads AC Resistive Loads AC Inductive Loads 8 12 VDC Resistive Loads 4 24 VDC Resistive Loads 8

10 Typical Performance Data Load effect on THID Figure 1 Typical Harmonic Spectrum With and Without Matrix AP Harmonic Filter Figure 2 9

11 Power Factor Figure 3 Performance with Unbalanced Line Voltage (Typical) Table 2 All Components at Nominal Values and Worse Case Service Conditions 100% Load Nominal THID 4.2% 1% Unbalance 4.4% 2% Unbalance 4.8% 3% Unbalance 5.4% 30% Load Nominal THID 7.0% 1% Unbalance 7.3% 2% Unbalance 7.9% 3% Unbalance 8.8% 10

12 Altitude De-rating Curve Figure 4 Altitude Derating Curve Current De-Rating Factor Altitude (Feet) Temperature De-rating Curve Figure 5 Note: Contact factory if Ambient is 20 C above temperature rating. See or click Specifications for temperature ratings 11

13 Voltage Distortion De-rating Curve Figure 6 This plot assists in proper de-rating of a Matrix AP Harmonic Filter in environments with a given voltage distortion. Example: In a system with 10% voltage distortion, a Matrix filter will need to be oversized by 25% to obtain the same performance as an appropriate filter in a 0% distortion environment. 12

14 MATRIX AP 400 VOLTS, 50Hz Selection Tables OPEN PANEL & GENERAL PURPOSE NEMA 1/2 Filter Style Filter Max Load Amps Motor KW NEC Motor Amps OPEN PANEL GEN L PURPOSE NEMA 2 Cat. No. Cat. No MAPP0006C MAPG0006C MAPP0008C MAPG0008C MAPP0011C MAPG0011C MAPP0014C MAPG0014C MAPP0021C MAPG0021C MAPP0027C MAPG0027C MAPP0034C MAPG0034C MAPP0044C MAPG0044C 30 MAPP00C MAPG00C MAPP0066C MAPG0066C MAPP0083C MAPG0083C MAPP0103C MAPG0103C MAPP0128C MAPG0128C MAPP0165C MAPG0165C MAPP0208C MAPG0208C MAPP0240C MAPG0240C MAPP0320C MAPG0320C MAPP0403C MAPG0403C MAPP0482C MAPG0482C MAPP0636C MAPG0636C MAPP0786C MAPP0850C MAPG0786C MAPG0850C MAPP1000C MAPG1000C MAPP1200C MAPG1200C 13

15 MATRIX AP 400 VOLTS, 50Hz Selection Tables NEMA 3R Enclosures GEN L PURPOSE NEMA 3R Filter Max Load Amps Motor KW MAPW0006C MAPW0008C MAPW0011C MAPW0014C MAPW0021C MAPW0027C MAPW0034C MAPW0044C 30 MAPW00C MAPW0066C MAPW0083C MAPW0103C MAPW0128C MAPW0165C MAPW0208C MAPW0240C MAPW0320C MAPW0403C MAPW0482C MAPW0636C MAPW0786C MAPW0850C MAPW1000C MAPW1200C NEC Motor Amps Cat. No. 14

16 MATRIX AP 400 VOLTS, 50Hz Ratings Watts loss Table 10 Maximum Output Amps RMS Efficiency (Typical) (%) 400V Power Rated Current (Typical) (Watts) % 97.6% 97.9% 98.1% 98.6% 98.7% 98.8% 98.9% 99.0% 99.1% 99.1% 99.2% 99.0% 99.2% 99.2% 99.2% 99.4% 99.4% 99.5% 99.5% 99.6% 99.6% 99.5% 99.6% ,030 1,263 1,423 1,450 1,816 2,008 2,359 2,604 2,974 3,954 4,

17 MATRIX AP 400 VOLTS, 50Hz Regulation table Table 11 FILTER VOLTAGE REGULATION * 400 VAC MAXIMUM OUTPUT VOLTAGE AT NO LOAD RMS PEAK MINIMUM OUTPUT VOLTAGE AT FULL LOAD RMS PEAK * RMS PEAK MAXIMUM PCC VOLTAGE WITH 6% SOURCE IMPEDANCE Note: PCC is the point of common coupling with the power distribution system 16

18 MATRIX AP 400 VOLTS, 50Hz Capacitor Currents Table 12 Filter Current Rating Amps RMS Capacitor Current 400V (Typical) Amps RMS Note: Ratings are based on IEC AC-3 specifications. 17

19 MATRIX AP 400 VOLTS, 50Hz Open Style Size and Weights Table 13 Cap-Panel P.N. Capacitor / Capacitor assemblies size Inches Cap Ref. Figure 8.7 H X 8 W X 5.5 D HMR Ref. Figure CAP-350TP 7.5 H X 2.9 D H X 8 W X 5.5 D CAP-351TP 7.5 H X 2.9 D MAPP0011C H X 9 W X 4.8 D CAP-3TP 7.5 H X 2.9 D 14 MAPP0014C H X 9 W X 5.25 D CAP-353TP 7.5 H X 3.9 D 21 MAPP0021C H X 10.5 W X 6.6 D CAP-342TP 7.5 H X 3.9 D 27 MAPP0027C 11.7 H X 10.5 W X 7 D CAP-354TP 7.5 H X 4.6 D 34 MAPP0034C H X 10.5 W X 7.6 D CAP-355TP 9.1 H X 4.6 D 44 MAPP0044C H X 10.5 W X 8 D CAP-356TP 9.1 H X 4.6 D MAPP00C H X 12 W X 9 D Figure 11 CAP-357TP 10.6 H X 4.6 D 66 MAPP0066C H X 12 W X 9 D Figure 11 CAP-358TP 10.6 H X 4.6 D 83 MAPP0083C H X 12 W X 10.9 D Figure 11 CAP-359TP 10.6 H X 4.6 D 103 MAPP0103C H X 12 W X D Figure 11 CAP-360TP 10.6 H X 4.6 D 128 MAPP0128C H X W X 10.7 D Figure H X 16.3 W X 7.6 D 165 MAPP0165C H X15.25 W X D Figure H X 16.3 W X 7.6 D 208 MAPP0208C H X W X D Figure H X 16.3 W X7.6 D 240 MAPP0240C H X W X D Figure H X 16.3 W X 7.6 D 320 MAPP0320C H X W X 14.8 D Figure X 16.3 W X 7.6 D 403 MAPP0403C H X W X13.86 D Figure H X 16.3 X 7.6 D 482 MAPP0482C 483 Figure H X 16.3 W X 7.6 D H X W X14.77 D H X 16.3 W X 7.6 D 636 MAPP0636C X 16.3 W X 7.6 D 26 H X 24 W X 16.5 D X 16.3 W X 7.6 D 786 MAPP0786C H X 16.3 X 7.6 D 26 H X 24 W X 17.8 D H X 16.3 X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D H X 16.3 W X 7.6 D H X 16.3 X 7.6 D H X 16.3 X 7.6 D H X 16.3 X 7.6 D H X 16.3 X 7.6 D H X 16.3 X 7.6 D H X 16.3 X 7.6 D Amps rating Catalog Part Number Total Weight Lbs. HMR Size Inches 6 MAPP0006C 16 8 MAPP0008C MAPP0850C MAPP1000C MAPP1200C H X 24 W X 20.3 D 26 H X 24 W X 21.7 D 26 H X 24 W X 22.2 D Figure 15 Figure 15 Figure 15 Figure 15 Figure 15 18

20 MATRIX AP 400 VOLTS, 50Hz Enclosed Unit Size and Weights Table 14 Filter Amps NEMA 2 Enclosure Weight NEMA 3R Enclosure Weight Figure 6 MAPG0006C CAB-12AP2 65 MAPW0006C CAB-12AP3 73 Figure 30 8 MAPG0008C CAB-12AP2 65 MAPW0008C CAB-12AP3 73 Figure MAPG0011C CAB-12AP2 75 MAPW0011C CAB-12AP3 82 Figure MAPG0014C CAB-12AP2 81 MAPW0014C CAB-12AP3 88 Figure MAPG0021C CAB-12AP2 97 MAPW0021C CAB-12AP3 105 Figure MAPG0027C CAB-12AP2 104 MAPW0027C CAB-12AP3 111 Figure MAPG0034C CAB-12AP2 115 MAPW0034C CAB-12AP3 123 Figure MAPG0044C CAB-12AP2 127 MAPW0044C CAB-12AP3 135 Figure 30 MAPG00C CAB-17AP2 174 MAPW00C CAB-17AP3 181 Figure MAPG0066C CAB-17AP2 186 MAPW0066C CAB-17AP3 194 Figure MAPG0083C CAB-17AP2 210 MAPW0083C CAB-17AP3 217 Figure MAPG0103C CAB-17AP2 221 MAPW0103C CAB-17AP3 228 Figure MAPG0128C CAB-26AP2 361 MAPW0128C CAB-26AP3 374 Figure MAPG0165C CAB-26AP2 429 MAPW0165C CAB-26AP3 442 Figure MAPG0208C CAB-26AP2 444 MAPW0208C CAB-26AP3 457 Figure MAPG0240C CAB-26AP2 476 MAPW0240C CAB-26AP3 489 Figure MAPG0320C CAB-26APD2 643 MAPW0320C CAB-26APD3 675 Figure MAPG0403C CAB-26APD2 637 MAPW0403C CAB-26APD3 669 Figure MAPG0482C CAB-42AP2 734 MAPW0482C CAB-42AP3 739 Figure MAPG0636C CAB-42AP MAPW0636C CAB-42AP Figure MAPG0786C CAB-42AP CAB-42AP Figure MAPG0850C CAB48AP MAPW0786C MAPW0850C CAB-48AP Figure MAPG1000C CAB48AP MAPW1000C CAB-48AP Figure MAPG1200C CAB48AP MAPW1200C CAB-48AP Figure 35 Note: Weight is shown in pounds 19

21 MATRIX AP 400 VOLTS, 50Hz MOUNTING PATTERNS AP HMR Bolt Hole Mounting Patterns Table H X 8 W X 5.5 D Rear Mount Centerline 7 A X 7.2 B Base Mount Centerline 2.8 C X 7.2 E H X 8 W X 5.5 D 7 A X 7.2 B 2.8 C X 7.2 E Mounting Holes.28 DIA.28 DIA MAPP0011C H X 9 W X 4.8 D 8.2 A X 8.2 B 2.75 C X 8.2 E.28 DIA MAPP0014C H X 9 W X 5.25 D 8.15 A X 8.2 B 3.25 C X 8.2 E.28 DIA 3.5 C X 9.7 E.28 DIA 4 C X 9.7 E.28 DIA Part Number Lbs. Overall Size MAPP0006C 16 MAPP0008C MAPP0021C MAPP0027C H X 10.5 W X 6.6 D 11.7 H X 10.5 W X 7 D 9.8 A X 9.7 B 9.9 A X 9.7 B Figure MAPP0034C H X 10.5 W X 7.6 D 9.8 A X 9.7 B 4.5 C X 9.7 E.28 DIA MAPP0044C H X 10.5 W X 8 D 9.8 A X 9.7 B 5 C X 9.7 E.28 DIA MAPP00C H X 12 W X 9 D 12 A X 11 B 5.4 C X 11 E.340 DIA Figure 11 MAPP0066C H X 12 W X 9 D 12 A X 11 B 5.9 C X 11 E.340 DIA Figure 11 MAPP0083C H X 12 W X 10.9 D 11.96''A x 11''B 6.5 C X 11 E.340 DIA Figure 11 MAPP0103C H X 12 W X 10.8 D 12.05'A x 11''B 6.5 C X 11 E.340 DIA Figure 11 MAPP0128C H X W X 10.7 D A X 14 B 6 C X 14 E.413 DIA Figure 12 MAPP0165C H X15.25 W X D A X 14 B 7 C X 14 E.413 DIA Figure 12 MAPP0208C H X W X D A X 14 B 7 C X 14 E.413 DIA Figure 12 MAPP0240C H X W X D A X 14 B 8 C X 14 E.413 DIA Figure 12 MAPP0320C H X W X 14.8 D A X 14 B 10 C x 14 E.413 DIA Figure 12 MAPP0403C H X W X13.86 D A X 14 B 9.2 C x 14 E.413 DIA Figure 13 MAPP0482C H X W X14.77 D A X 14 B C X 14 E.413 DIA Figure 13 MAPP0636C H X 24 W X 16.5 D 9.15 C X 22 E 1 DIA Figure 15 MAPP0786C H X 24 W X 17.8 D C X 22 E 1 DIA Figure 15 MAPP0850C H X 24 W X D C X 22 E 1 DIA Figure 15 MAPP1000C H X 24 W X 21.7 D C X 22 E 1 DIA Figure 15 MAPP1200C H X 24 W X 22.2 D C X 22 E 1 DIA Figure 15 Use the above table and referenced figures to establish suitable reactor mounting. 20

22 MATRIX AP 400 VOLTS, 50Hz Capacitor and Cap-panel Bolt Hole Mounting Patterns Table 16 Part Number MAPP0006C CAP-350TP Weight Lbs. 1.8 Mounting Holes Figure 7.5 H X 2.9 D Rear Mount Centerline MAPP0008C CAP-351TP H X 2.9 D MAPP0011C CAP-3TP H X 2.9 D MAPP0014C CAP-353TP H X 3.9 D MAPP0021C CAP-342TP H X 3.9 D MAPP0027C CAP-354TP H X 4.6 D MAPP0034C CAP-355TP H X 4.6 D MAPP0044C CAP-356TP H X 4.6 D MAPP00C CAP-357TP H X 4.6 D MAPP0066C CAP-358TP H X 4.6 D MAPP0083C CAP-359TP H X 4.6 D MAPP0103C CAP-360TP H X 4.6 D MAPP0128C H X 16.3 W X 7.6 D MAPP0165C H X 16.3 W X 7.6 D MAPP0208C H X 16.3 W X7.6 D MAPP0240C H X 16.3 W X 7.6 D MAPP0320C X 16.3 W X 7.6 D MAPP0403C X 16.3 X 7.6 D H X 16.3 W X 7.6 D H X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D H X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D MAPP0482C MAPP0636C MAPP0786C MAPP0850C MAPP1000C MAPP1200C CAP P.N. Overall Size Note: Units above 403 amps require multiple parallel cap panels. Use the above table and referenced figures to establish suitable Cap-panel mounting. 21

23 MATRIX AP 480 VOLTS, 60Hz Selection Tables OPEN PANEL & GENERAL PURPOSE NEMA 1/2 Filter Style Filter Max Load Amps Motor HP NEC Motor Amps OPEN PANEL GEN L PURPOSE NEMA 2 Cat. No. Cat. No MAPP0006D MAPG0006D MAPP0008D MAPG0008D MAPP0011D MAPG0011D MAPP0014D MAPG0014D MAPP0021D MAPG0021D MAPP0027D MAPG0027D MAPP0034D MAPG0034D MAPP0044D MAPG0044D 40 MAPP00D MAPG00D MAPP0066D MAPG0066D MAPP0083D MAPG0083D MAPP0103D MAPG0103D MAPP0128D MAPG0128D MAPP0165D MAPG0165D MAPP0208D MAPG0208D MAPP0240D MAPG0240D MAPP0320D MAPG0320D MAPP0403D MAPG0403D MAPP0482D MAPG0482D MAPP0636D MAPG0636D MAPP0786D MAPG0786D MAPP0850D MAPG0850D MAPP1000D MAPG1000D MAPP1200D MAPG1200D 22

24 MATRIX AP 480 VOLTS, 60Hz Selection Tables NEMA 3R Enclosures GEN L PURPOSE NEMA 3R Filter Max Load Amps Motor HP MAPW0006D MAPW0008D MAPW0011D MAPW0014D MAPW0021D MAPW0027D MAPW0034D MAPW0044D 40 MAPW00D MAPW0066D MAPW0083D MAPW0103D MAPW0128D MAPW0165D MAPW0208D MAPW0240D MAPW0320D MAPW0403D MAPW0482D MAPW0636D MAPW0786D MAPW0850D MAPW1000D MAPW1200D NEC Motor Amps Cat. No. 23

25 MATRIX AP 480 VOLTS, 60Hz Ratings Watts loss Table 20 Maximum Output Amps RMS Efficiency (Typical) (%) 480V Power Rated Current (Typical) (Watts) % 97.6% 97.9% 98.1% 98.6% 98.7% 98.8% 98.9% 99.0% 99.1% 99.1% 99.2% 99.0% 99.2% 99.2% 99.2% 99.4% 99.4% 99.5% 99.5% 99.6% 99.6% 99.5% 99.6% ,035 1,096 1,343 1,514 1,543 1,932 2,137 2,509 2,771 3,163 4,206 4,

26 MATRIX AP 480 VOLTS, 60Hz Regulation table Table 21 FILTER VOLTAGE REGULATION MAXIMUM OUTPUT VOLTAGE AT NO LOAD RMS PEAK MINIMUM OUTPUT VOLTAGE AT FULL LOAD RMS PEAK * RMS PEAK MAXIMUM PCC VOLTAGE WITH 6% SOURCE IMPEDANCE * 480 VAC Note: PCC is the point of common coupling with the power distribution system 25

27 MATRIX AP 480 VOLTS, 60Hz Capacitor Currents Table 22 Filter Current Rating Amps RMS Capacitor Current 480V (Typical) Amps RMS Note: Ratings are based on IEC AC-3 specifications. 26

28 MATRIX AP 480 VOLTS, 60Hz Open Style Size and Weights Table 23 Cap-Panel P.N. Capacitor / Capacitor assemblies size Inches Cap Ref. Figure 8.7 H X 8 W X 5.5 D HMR Ref. Figure CAP-338TP 7.5 H X 2.9 D H X 8 W X 5.5 D CAP-339TP 7.5 H X 2.9 D MAPP0011D H X 9 W X 4.8 D CAP-349TP 7.5 H X 2.9 D 14 MAPP0014D H X 9 W X 5.25 D CAP-340TP 7.5 H X 2.9 D 21 MAPP0021D H X 10.5 W X 6.6 D CAP-341TP 7.5 H X 3.9 D 27 MAPP0027D 11.7 H X 10.5 W X 7 D CAP-342TP 7.5 H X 3.9 D 34 MAPP0034D H X 10.5 W X 7.6 D CAP-343TP 7.5 H X 3.9 D 44 MAPP0044D H X 10.5 W X 8 D CAP-344TP 7.5 H X 4.6 D MAPP00D H X 12 W X 9 D Figure 11 CAP-345TP 9.2 H X 4.6 D 66 MAPP0066D H X 12 W X 9 D Figure 11 CAP-346TP 9.2 H X 4.6 D 83 MAPP0083D H X 12 W X 10.9 D Figure 11 CAP-347TP 10.6 H X 4.6 D 103 MAPP0103D H X 12 W X D Figure 11 CAP-348TP 10.6 H X 4.6 D 128 MAPP0128D H X W X 10.7 D Figure H X 16.3 W X 7.6 D 165 MAPP0165D H X15.25 W X D Figure H X 16.3 W X 7.6 D 208 MAPP0208D H X W X D Figure H X 16.3 W X7.6 D 240 MAPP0240D H X W X D Figure H X 16.3 W X 7.6 D 320 MAPP0320D H X W X 14.8 D Figure X 16.3 W X 7.6 D 403 MAPP0403D H X W X13.86 D Figure X 16.3 X 7.6 D 482 MAPP0482D 483 Figure H X 16.3 W X 7.6 D H X W X14.77 D H X 16.3 W X 7.6 D 636 MAPP0636D X 16.3 W X 7.6 D 26 H X 24 W X 16.5 D X 16.3 W X 7.6 D 786 MAPP0786D X 16.3 X 7.6 D 26 H X 24 W X 17.8 D X 16.3 X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D H X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D Amps rating Catalog Part Number Total Weight Lbs. HMR Size Inches 6 MAPP0006D 16 8 MAPP0008D MAPP0850D MAPP1000D MAPP1200D H X 24 W X 20.3 D 26 H X 24 W X 21.7 D 26 H X 24 W X 22.2 D Figure 15 Figure 15 Figure 15 Figure 15 Figure 15 27

29 MATRIX AP 480 VOLTS, 60Hz Enclosed Unit Size and Weights Table 24 Filter Amps NEMA 2 Enclosure Weight NEMA 3R Enclosure Weight Figure 6 MAPG0006D CAB-12AP2 64 MAPW0006D CAB-12AP3 72 Figure 30 8 MAPG0008D CAB-12AP2 65 MAPW0008D CAB-12AP3 73 Figure MAPG0011D CAB-12AP2 74 MAPW0011D CAB-12AP3 82 Figure MAPG0014D CAB-12AP2 79 MAPW0014D CAB-12AP3 87 Figure MAPG0021D CAB-12AP2 97 MAPW0021D CAB-12AP3 105 Figure MAPG0027D CAB-12AP2 101 MAPW0027D CAB-12AP3 109 Figure MAPG0034D CAB-12AP2 112 MAPW0034D CAB-12AP3 120 Figure MAPG0044D CAB-12AP2 125 MAPW0044D CAB-12AP3 133 Figure 30 MAPG00D CAB-17AP2 172 MAPW00D CAB-17AP3 179 Figure MAPG0066D CAB-17AP2 185 MAPW0066D CAB-17AP3 192 Figure MAPG0083D CAB-17AP2 209 MAPW0083D CAB-17AP3 217 Figure MAPG0103D CAB-17AP2 313 MAPW0103D CAB-17AP3 321 Figure MAPG0128D CAB-26AP2 333 MAPW0128D CAB-26AP3 347 Figure MAPG0165D CAB-26AP2 392 MAPW0165D CAB-26AP3 406 Figure MAPG0208D CAB-26AP2 405 MAPW0208D CAB-26AP3 419 Figure MAPG0240D CAB-26AP2 489 MAPW0240D CAB-26AP3 503 Figure MAPG0320D CAB-26APD2 630 MAPW0320D CAB-26APD3 656 Figure MAPG0403D CAB-26APD2 673 MAPW0403D CAB-26APD3 700 Figure MAPG0482D CAB-42AP2 702 MAPW0482D CAB-42AP3 710 Figure MAPG0636D CAB-42AP MAPW0636D CAB-42AP Figure MAPG0786D CAB-42AP2 12 MAPW0786D CAB-42AP Figure MAPG0850D CAB48AP MAPW0850D CAB-48AP Figure MAPG1000D CAB48AP MAPW1000D CAB-48AP Figure MAPG1200D CAB48AP MAPW1200D CAB-48AP Figure 35 Note: Weight is shown in pounds 28

30 MATRIX AP 480 VOLTS, 60Hz MOUNTING PATTERNS AP HMR Bolt Hole Mounting Patterns Table H X 8 W X 5.5 D Rear Mount Centerline 7 A X 7.2 B Base Mount Centerline 2.8 C X 7.2 E 8.7 H X 8 W X 5.5 D 7 A X 7.2 B 2.8 C X 7.2 E Mounting Holes.28 DIA.28 DIA 2.75 C X 8.2 E.28 DIA 3.25 C X 8.2 E.28 DIA 3.5 C X 9.7 E.28 DIA Part Number Lbs. Overall Size MAPP0006D 16 MAPP0008D 17 MAPP0011D MAPP0014D H X 9 W X 4.8 D 9.8 H X 9 W X 5.25 D 8.2 A X 8.2 B 8.15 A X 8.2 B 9.8 A X 9.7 B Figure MAPP0021D H X 10.5 W X 6.6 D MAPP0027D 11.7 H X 10.5 W X 7 D 9.9 A X 9.7 B 4 C X 9.7 E.28 DIA MAPP0034D H X 10.5 W X 7.6 D 9.8 A X 9.7 B 4.5 C X 9.7 E.28 DIA MAPP0044D H X 10.5 W X 8 D 9.8 A X 9.7 B 5 C X 9.7 E.28 DIA MAPP00D H X 12 W X 9 D 12 A X 11 B 5.4 C X 11 E.340 DIA Figure 11 MAPP0066D H X 12 W X 9 D 12 A X 11 B 5.9 C X 11 E.340 DIA Figure 11 MAPP0083D H X 12 W X 10.7 D 11.96''A x 11''B 6.5 C X 11 E.340 DIA Figure 11 MAPP0103D H X 12 W X 11.1 D 12.05'A x 11''B 6.5 C X 11 E.340 DIA Figure 11 MAPP0128D H X W X 10.7 D A X 14 B 6 C X 14 E.413 DIA Figure 12 MAPP0165D H X15.25 W X D A X 14 B 7 C X 14 E.413 DIA Figure 12 MAPP0208D H X W X D A X 14 B 7 C X 14 E.413 DIA Figure 12 MAPP0240D H X W X D A X 14 B 8 C X 14 E.413 DIA Figure 12 MAPP0320D H X W X 14.8 D A X 14 B 10 C x 14 E.413 DIA Figure 12 MAPP0403D H X W X13.86 D A X 14 B 9.2 C x 14 E.413 DIA Figure 13 MAPP0482D H X W X14.37 D A X 14 B C X 14 E.413 DIA Figure 13 MAPP0636D H X 24 W X 16.5 D 9.15 C X 22 E 1 DIA Figure 15 MAPP0786D H X 24 W X 17.8 D C X 22 E 1 DIA Figure 15 MAPP0850D H X 24 W X 20.3 D C X 22 E 1 DIA Figure 15 MAPP1000D H X 24 W X 21.7 D C X 22 E 1 DIA Figure 15 MAPP1200D H X 24 W X 22.2 D C X 22 E 1 DIA Figure 15 Use the above table and referenced figures to establish suitable reactor mounting. 29

31 MATRIX AP 480 VOLTS, 60Hz Capacitor and Cap-panel Bolt Hole Mounting Patterns Table 26 Part Number MAPP0006D CAP-338TP Weight Lbs. 1.8 Mounting Holes Figure 7.5 H X 2.9 D Rear Mount Centerline MAPP0008D CAP-339TP H X 2.9 D MAPP0011D CAP-349TP H X 2.9 D MAPP0014D CAP-340TP H X 2.9 D MAPP0021D CAP-341TP H X 3.9 D MAPP0027D CAP-342TP H X 3.9 D MAPP0034D CAP-343TP H X 3.9 D MAPP0044D CAP-344TP H X 4.6 D MAPP00D CAP-345TP H X 4.6 D MAPP0066D CAP-346TP H X 4.6 D MAPP0083D CAP-347TP H X 4.6 D MAPP0103D CAP-348TP H X 4.6 D MAPP0128D H X 16.3 W X 7.6 D MAPP0165D H X 16.3 W X 7.6 D MAPP0208D H X 16.3 W X7.6 D MAPP0240D H X 16.3 W X 7.6 D MAPP0320D X 16.3 W X 7.6 D MAPP0403D X 16.3 X 7.6 D H X 16.3 W X 7.6 D H X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D H X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D MAPP0482D MAPP0636D MAPP0786D MAPP0850D MAPP1000D MAPP1200D CAP P.N. Overall Size Note: Units above 403 amps require multiple parallel cap panels. Use the above table and referenced figures to establish suitable Cap-panel mounting. 30

32 MATRIX AP 600 VOLTS, 60Hz Selection Tables OPEN PANEL & GENERAL PURPOSE NEMA 1/2 Filter Style Filter Max Load Amps 6 Motor HP 5 NEC Motor Amps 6.1* OPEN PANEL GEN L PURPOSE NEMA 2 Cat. No. Cat. No. MAPP0006E MAPG0006E MAPP0008E MAPG0008E MAPP0011E MAPG0011E MAPP0014E MAPG0014E MAPP0021E MAPG0021E MAPP0027E MAPG0027E MAPP0034E MAPG0034E MAPP0044E MAPG0044E 50 MAPP00E MAPG00E MAPP0066E MAPG0066E MAPP0083E MAPG0083E MAPP0103E MAPG0103E MAPP0128E MAPG0128E MAPP0165E MAPG0165E MAPP0208E MAPG0208E * MAPP0240E MAPG0240E MAPP0320E MAPG0320E MAPP0403E MAPG0403E MAPP0482E MAPG0482E MAPP0636E MAPG0636E MAPP0786E MAPG0786E 31

33 MATRIX AP 600 VOLTS, 60Hz Selection Tables NEMA 3R Enclosures Filter Max Load Amps Motor HP 6 5 NEC Motor Amps Cat. No. 6.1* 8 11 GEN L PURPOSE NEMA 3R MAPW0006E MAPW0008E MAPW0011E MAPW0014E MAPW0021E MAPW0027E MAPW0034E MAPW0044E 50 MAPW00E MAPW0066E MAPW0083E MAPW0103E MAPW0128E MAPW0165E MAPW0208E * MAPW0240E MAPW0320E MAPW0403E MAPW0482E MAPW0636E MAPW0786E 32

34 MATRIX AP 600 VOLTS, 60Hz Ratings Watts loss Table 30 Maximum Output Amps RMS Efficiency (Typical) (%) 600V Power Rated Current (Typical) (Watts) % 97.8% 98.2% 98.3% 98.7% 98.9% 99.0% 99.1% 99.1% 99.0% 99.1% 99.0% 99.2% 99.3% 99.3% 99.3% 99.4% 99.5% 99.5% 99.6% 99.6%

35 MATRIX AP 600 VOLTS, 60Hz Regulation table Table 31 FILTER VOLTAGE REGULATION 600 VAC MAXIMUM OUTPUT VOLTAGE AT NO LOAD RMS PEAK MINIMUM OUTPUT VOLTAGE AT FULL LOAD RMS PEAK *MAXIMUM PCC VOLTAGE WITH 6% SOURCE IMPEDANCE RMS PEAK Note: PCC is the point of common coupling with the power distribution system 34

36 MATRIX AP 600 VOLTS, 60Hz Capacitor Currents Table 32 Filter Current Rating Amps RMS Capacitor Current 600V (Typical) Amps RMS Note: Ratings are based on IEC AC-3 specifications. 35

37 MATRIX AP 600 VOLTS, 60Hz Open Style Size and Weights Table 33 Cap-Panel P.N. Capacitor / Capacitor assemblies size Inches Cap Ref. Figure 8.7 H X 8 W X 5.5 D HMR Ref. Figure CAP-361TP 7.5 H X 2.9 D H X 9 W X 4.8 D CAP-362TP 7.5 H X 2.9 D MAPP0011E H X 9 W X 5.3 D CAP-363TP 7.5 H X 2.9 D 14 MAPP0014E H X 10.5 W X 6.6 D CAP-364TP 7.5 H X 3.9 D 21 MAPP0021E 11.7 H X 10.5 W X 7.1 D CAP-365TP 7.5 H X 3.9 D 27 MAPP0027E H X 10.5 W X 7.6 D CAP-366TP 7.5 H X 4.6D 34 MAPP0034E H X 10.5 W X 8.1 D CAP-367TP 7.5 H X 4.6 D 44 MAPP0044E H X 12 W X 9.89 D Figure 11 CAP-368TP 9.14 H X 4.6 D MAPP00E H X 12 W X 10.3 D Figure 11 CAP-369TP 9.14 H X 4.6 D 66 MAPP0066E H X 12 W X 11 D Figure 11 CAP-370TP 10.6 H X 4.6 D 83 MAPP0083E H X 12 W X 11 D Figure 11 CAP-371TP 10.6 H X 4.6 D 103 MAPP0103E H X 15.3 W X 10.7 D Figure H X 16.3 W X 7.6 D 128 MAPP0128E H X 15.3 W X 11.7 D Figure H X 16.3 W X 7.6 D 165 MAPP0165E H X15.3 W X 11.9 D Figure H X 16.3 W X 7.6 D 208 MAPP0208E H X 15.3 W X 13.4 D Figure H X 16.3 W X7.6 D 240 MAPP0240E H X 15.3 W X 16.1 D Figure H X 16.3 W X 7.6 D 320 MAPP0320E H X 15.3 W X 15.7 D Figure X 16.3 W X 7.6 D 403 MAPP0403E H X 15.3 W X16.1 D Figure X 16.3 X 7.6 D 482 MAPP0482E 736 Figure H X 16.3 W X 7.6 D 25.8 H X 24 W X16.7 D H X 16.3 W X 7.6 D 636 MAPP0636E X 16.3 W X 7.6 D 25.9 H X 24 W X 18.2 D X 16.3 W X 7.6 D 786 MAPP0786E X 16.3 X 7.6 D 25 H X 24 W X 19.5 D X 16.3 X 7.6 D Amps rating Catalog Part Number Total Weight Lbs. HMR Size Inches 6 MAPP0006E 17 8 MAPP0008E 11 Figure 16 Figure 16 36

38 MATRIX AP 600 VOLTS, 60Hz Enclosed Unit Size and Weights Table 34 Filter Amps NEMA 2 Enclosure Weight NEMA 3R Enclosure Weight Figure 6 MAPG0006E CAB-12AP2 65 MAPW0006E CAB-12AP3 73 Figure 30 8 MAPG0008E CAB-12AP2 74 MAPW0008E CAB-12AP3 82 Figure MAPG0011E CAB-12AP2 79 MAPW0011E CAB-12AP3 87 Figure MAPG0014E CAB-12AP2 97 MAPW0014E CAB-12AP3 105 Figure MAPG0021E CAB-12AP2 101 MAPW0021E CAB-12AP3 109 Figure MAPG0027E CAB-12AP2 112 MAPW0027E CAB-12AP3 120 Figure MAPG0034E CAB-12AP2 125 MAPW0034E CAB-12AP3 133 Figure MAPG0044E CAB-17AP2 172 MAPW0044E CAB-17AP3 179 Figure 31 MAPG00E CAB-17AP2 185 MAPW00E CAB-17AP3 192 Figure MAPG0066E CAB-17AP2 209 MAPW0066E CAB-17AP3 217 Figure MAPG0083E CAB-17AP2 313 MAPW0083E CAB-17AP3 338 Figure MAPG0103E CAB-26AP2 333 MAPW0103E CAB-26AP3 358 Figure MAPG0128E CAB-26AP2 392 MAPW0128E CAB-26AP3 417 Figure MAPG0165E CAB-26AP2 405 MAPW0165E CAB-26AP3 430 Figure MAPG0208E CAB-26AP2 489 MAPW0208E CAB-26AP3 514 Figure MAPG0240E CAB-26APD2 630 MAPW0240E CAB-26APD3 656 Figure MAPG0320E CAB-26APD2 673 MAPW0320E CAB-26APD3 700 Figure MAPG0403E CAB-42AP2 702 MAPW0403E CAB-42AP3 710 Figure MAPG0482E CAB-42AP MAPW0482E CAB-42AP Figure MAPG0636E CAB-42AP2 12 MAPW0636E CAB-42AP Figure MAPG0786E CAB-48AP MAPW0786E CAB-48AP Figure 35 Note: Weight is shown in pounds 37

39 MATRIX AP 600 VOLTS, 60Hz MOUNTING PATTERNS AP HMR Bolt Hole Mounting Patterns Table H X 8 W X 5.5 D Rear Mount Centerline 7 A X 7.2 B Base Mount Centerline 2.8 C X 7.2 E 8.7 H X 8 W X 5.5 D 8.2 A X 8.2 B 2.8 C X 8.2 E Mounting Holes.28 DIA.28 DIA 3.3 C X 8.2 E.28 DIA 3.5 C X 9.7 E.28 DIA 4 C X 9.7 E.28 DIA Part Number Lbs. Overall Size MAPP0006E 17 MAPP0008E 26 MAPP0011E MAPP0014E H X 9 W X 4.8 D 9.8 H X 9 W X 5.25 D 8.1 A X 8.2 B 9.9 A X 9.7 B 9.9 A X 9.7 B Figure MAPP0021E 11.7 H X 10.5 W X 6.6 D MAPP0027E H X 10.5 W X 7 D 9.9 A X 9.7 B 4.5 C X 9.7 E.28 DIA MAPP0034E H X 10.5 W X 7.6 D 9.9 A X 9.7 B 5 C X 9.7 E.28 DIA MAPP0044E H X 10.5 W X 8 D 12 A X 11 B 5.9 C X 11 E.28 DIA Figure 11 MAPP00E H X 12 W X 9 D 11.6 A X 11 B 6.4 C X 11 E.340 DIA Figure 11 MAPP0066E H X 12 W X 9 D 11.8 A X 11 B 6.9 C X 11 E.340 DIA Figure 11 MAPP0083E H X 12 W X 10.7 D 11.6''A x 11''B 6.9 C X 11 E.340 DIA Figure 11 MAPP0103E H X 12 W X 11.1 D 17.1 x 14''B 6 C X 14 E.340 DIA Figure 12 MAPP0128E H X W X 10.7 D 17 A X 14 B 7 C X 14 E.413 DIA Figure 12 MAPP0165E H X15.25 W X D 17.4 A X 14 B 7 C X 14 E.413 DIA Figure 12 MAPP0208E H X W X D 17.2 A X 14 B 8 C X 14 E.413 DIA Figure 12 MAPP0240E H X W X D 17.3 A X 14 B 10 C X 14 E.413 DIA Figure 14 MAPP0320E H X W X 14.8 D 20.4 A X 14 B 10 C x 14 E.413 DIA Figure 14 MAPP0403E H X W X13.86 D 20.9 A X 14 B 10 C x 14 E.413 DIA Figure 14 MAPP0482E H X W X14.37 D 9.2 C X 22 E.413 DIA Figure 16 MAPP0636E H X 24 W X 16.5 D 10.7 C X 22 E 1 DIA Figure 16 MAPP0786E H X 24 W X 17.8 D 12.2 C X 22 E 1 DIA Figure 16 Use the above table and referenced figures to establish suitable reactor mounting. 38

40 MATRIX AP 600 VOLTS, 60Hz Capacitor and Cap-panel Bolt Hole Mounting Patterns Table 36 Part Number CAP P.N. MAPP0006E CAP-361TP Weight Lbs. 1.8 Mounting Holes Figure 7.5 H X 2.9 D Rear Mount Centerline MAPP0008E CAP-362TP H X 2.9 D MAPP0011E CAP-363TP H X 2.9 D MAPP0014E CAP-364TP H X 2.9 D MAPP0021E CAP-365TP H X 3.9 D MAPP0027E CAP-366TP H X 3.9 D MAPP0034E CAP-367TP H X 3.9 D MAPP0044E CAP-368TP H X 4.6 D MAPP00E CAP-369TP H X 4.6 D MAPP0066E CAP-370TP H X 4.6 D MAPP0083E CAP-371TP H X 4.6 D MAPP0103E H X 16.3 W X 7.6 D MAPP0128E H X 16.3 W X 7.6 D MAPP0165E H X 16.3 W X 7.6 D MAPP0208E H X 16.3 W X7.6 D MAPP0240E H X 16.3 W X 7.6 D MAPP0320E X 16.3 W X 7.6 D MAPP0403E X 16.3 X 7.6 D H X 16.3 W X 7.6 D H X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 W X 7.6 D X 16.3 X 7.6 D X 16.3 X 7.6 D MAPP0482E MAPP0636E MAPP0786E Overall Size Note: Units above 403 amps require multiple parallel cap panels. Use the above table and referenced figures to establish suitable Cap-panel mounting. 39

41 AP HMR MOUNTING & TERMINAL LOCATIONS AP HMR 6 44 Amp (400V & 480V) AP HMR 6 34 Amp (600V) Refer to the MTE website, for Detailed Specifications. 40

42 AP HMR MOUNTING & TERMINAL LOCATIONS AP HMR 103 Amp (400V & 480V) AP HMR Amp (600V) Customer Connections to HMR: Input: U1-V1-W1 Output: U2-V2-W2 Figure 11 Refer to the MTE website, for Detailed Specifications. 41

43 AP HMR MOUNTING & TERMINAL LOCATIONS AP HMR Amp (400V & 480V) AP HMR Amp (600V) Customer Connections to HMR: Output: U2-V2-W2 Input: U1-V1-W1 Figure 12 Refer to the MTE website, for Detailed Specifications. 42

44 AP HMR MOUNTING & TERMINAL LOCATIONS AP HMR Amp (400V & 480V) Customer Connections to HMR: Output: U2-V2-W2 Input: U1-V1-W1 Figure 13 Refer to the MTE website, for Detailed Specifications. 43

45 AP HMR MOUNTING & TERMINAL LOCATIONS AP HMR Amp (600V) Customer Connections to HMR: Input: U1-V1-W1 Output: U2-V2-W2 Figure 14 Refer to the MTE website, for Detailed Specifications. 44

46 AP HMR MOUNTING & TERMINAL LOCATIONS AP HMR Amp (400V & 480V) Customer Connections to HMR: Output: U2-V2-W2 Input: U1-V1-W1 Figure 15 Refer to the MTE website, for Detailed Specifications. 45

47 AP HMR MOUNTING & TERMINAL LOCATIONS AP HMR Amp (600V) Customer Connections to HMR: Input: U1-V1-W1 Output: U2-V2-W2 Figure 16 Refer to the MTE website, for Detailed Specifications. 46

48 CAP-ASSEMBLY MOUNTING & TERMINAL LOCATIONS 1 Three Phase Capacitor Note: Height of capacitor will vary depending on the size of the filter. Refer to the MTE website, for Detailed Specifications. 47

49 CAP-ASSEMBLY MOUNTING & TERMINAL LOCATIONS Customer Connections to CAPPANEL: U4-V4-W4 3 High Current Capacitor Panel Note: Height of capacitors will vary depending on the size of the filter. Refer to the MTE website, for Detailed Specifications. 48

50 ENCLOSED UNIT INTERNAL DETAILS CAB-12AP Figure 30 Refer to the MTE website, for Detailed Specifications. 49

51 ENCLOSED UNIT INTERNAL DETAILS CAB-17AP Figure 31 Refer to the MTE website, for Detailed Specifications. 50

52 ENCLOSED UNIT INTERNAL DETAILS CAB-26AP Figure 32 Refer to the MTE website, for Detailed Specifications. 51

53 ENCLOSED UNIT INTERNAL DETAILS CAB-26APD Figure 33 Refer to the MTE website, for Detailed Specifications.

54 ENCLOSED UNIT INTERNAL DETAILS CAB-42AP Figure 34 Refer to the MTE website, for Detailed Specifications. 53

55 ENCLOSED UNIT INTERNAL DETAILS CAB-48AP Figure 35 Refer to the MTE website, for Detailed Specifications. 54

56 Open Panel Unit Interconnection Diagram Figure 40 55

57 Enclosed Unit Interconnection Diagram Figure 41 Matrix AP Harmonic Filter 56

58 Matrix AP Basic Schematic Diagram Figure 42 57

59 Contactor Options Option -002 Capacitor Contactor This option provides a contactor to disconnect the filter capacitor bank when the drive is not running. The contactor is supplied with NO/NC auxiliary contacts. The contactor coil and auxiliary contacts are wired to a customer terminal block. See page 61 for contactor coil switching characteristics. This option is provided prewired complete for enclosed filters and as loose parts for open panel filters. The above contactor option diagram is provided to help understand the circuit function and does not reflect actual circuit wiring. 58

60 Option -009 Capacitor Contactor with adjustable pick up and drop out This option provides a contactor to disconnect the filter capacitor bank based on the motor load current. Two current operated switches provide independent adjustment of the pick-up and drop current levels. The switches are preset at the factory for pick up at 35% and drop out at 20% of the filter output current rating. The switches are each field adjustable over a 0 100% current range. This option is only available for enclosed filters. The above contactor option diagram is provided to help understand the circuit function and does not reflect actual circuit wiring. 59

61 Option -012 Capacitor contactor with control transformer This option provides a control transformer to power the capacitor contactor. The contractor is provided with NO/NC auxiliary contacts. For filter ratings 165 amps and above a pilot relay is also provided to limit inrush current below 0.60 amps. Connections are wired to a customer terminal block. This option is only available for enclosed filters. The above contactor option diagram is provided to help understand the circuit function and does not reflect actual circuit wiring. 60

62 Contactor coil switching currents Table 50 Options 002 The following table indicates the 120 VAC 50/60 Hz current required to switch and hold the various size contactors used in Matrix Filter capacitor switching and bypass options. This data is provided to select the proper switch rating to remotely control the contactor and is consistent for the 400V, 480V, and 600V units. Contactor Currents for 120 VAC 50/60 Hz coils. Matrix filter current Rating AMPS Capacitor Contactor Option 002 AMPS INRUSH SEALED