Plate analysis using classical or Reissner- Mindlin theories

Size: px
Start display at page:

Download "Plate analysis using classical or Reissner- Mindlin theories"

Transcription

1 Plate analysis using classical or Reissner- Mindlin theories L. Palermo Jr. Faculty of Civil Engineering, State Universiv at Campinas, Brazil Abstract Plates can be solved with classical or Reissner-Mindlin plate theory in the same computer code with an appropriate treatment of the direct boundary element formulation. The classical theory could be understood as the irrotational component of the field related to the rotations of the plate [l] and the shear deformation effect would correspond to the solenoidal component. This paper presents the fundamental solution and the direct boundary integral equations written in terms of boundary coordinates, normal (n) and tangential (S), for Reissner-Mindlin theory like it has been made for the classical analysis in order to permit the desired connection. Thus, the correction introduced by transverse shear deformation on the bending can be identified with reference to the classical approach and it is the key to establish the connection among the studied theories. An examplc will be solved to show the connections among plates theories and to present a boundary element formulation for Mindlin's theory with the irrotational tield using the Danson's fundamental solution [5]. 1 Introduction The classical theory is written with reference to the out-of-plane displacement and its derivatives or, as it was shown in [l], the rotations of the plate can be represented by an irrotational field. The integral equation contains four boundary parameters and it is necessary to satisfy two boundary conditions to obtain a single solution. It must be pointed out that, beyond the two boundary unknowns, a concentrated reaction is placed at each corner as an additional parameter in the boundary value problem when a polygonal plate is considered. The inaccuracy of

2 the classical theory turns out to be of practical interest in the edge zone of a plate and around holes that have a diameter not larger than the thickness of the plate. In order to overcome the above-mentioned features due to one-displacement dependence of the classical theory. Mindlin [3] and Reissner [2] developed similar theories considering the shear deformation effect. Unless those theories have been conceived to treat thin or thick plates, they are frequently referred in numerical analysis as thick plates theories. The curvatures have not been directly related with out-of-plane displacement derivative in the constitutive equations and three boundary conditions should be satisfied in the boundary value problem rather than the two of classical theory. Bezine [6], Tottenham [S], Stern171 and Danson [5] made important contributions in the plate analyses with the classical theory using the Boundary Element Method (BEM). Weeen [4] introduced a BEM formulation applied to Reissner's theory; Barcellos [l l] and Vilmann [l01 used similar formulations to treat Mindlin's theory. The boundary integral equation (BIE) to perform those analyses has used six boundary parameters and no additional unknown had to be introduced when polygonal plates were considered. Katsikadelis [l51 presented a BEM formulation for the Reissner's theory. which was expressed in terms of two potentials, one biharmonic and one Bessel potential. The plates analyzed with that strategy needed three integral equations plus three finite difference equations. Mukherjee [9] and Paiva [l21 used the classical theory with an additional degree of freedom for the tangential boundary rotation into a boundary integral formulation and showed that many problems associated with the treatment with two-boundary parameters of this theory could be overcome. 2 Plate Equations The expressions will be presented with the Latin indices taking values {l, 2. 3) and Greek indices in the range { 1, 2). A plate of uniform thickness is referred to midline coordinates X, and thickness coordinate x3. The transverse shear (Q,), the bending and twisting moments (Map), all per unit of length, have similar definition in both theories with reference to the stress. In classical theory, the constitutive relations written in terms of deflections are: Map = -D((I - v ) ~ +v-., ~ W S ~ a(j ) (1) D is the flexural rigidity and v is the Poisson's ratio. Reissner conceived his theory from an assumed stress distribution and introduced generalized displacement expressions with a weighted average across the thickness [l 31 to get the deflection (W) of the plate in the middle surface and quantities (P,) representing components equivalent but not identical to the components of changes of slope. The constitutive equations written in terms of displacements (P,, W) are given by:

3 h is a constant related to shear effect and it is equal to &/h, Mindlin's theory [3] was conceived from an assumed strain distribution. The "equivalent changes of slope" P, of Reissner's theory were replaced by v, which were obtained without average expressions due to assumed strain hypothesis. The integrals to get shears, bending and twisting moments were performed but the coefficients of the integrals containing y,, were replaced by constants whose magnitude were obtained from wave propagation analyses. The constitutive relations for Mindlin's theory are: Mindlin showed that h is related to the Poisson ratio and the vibration mode including the transverse shear deformation and the rotatory inertia effects. In the present study, h will be assumed as n/h independently of the Poisson ratio. Further, it is necessary to note in equation (6) with reference to equation (4) that the distributed load effect was not include. It can be shown from Reissner's studies that this feature is related to the 033 stress effect. However. since the average expressions for the displacements have been introduced by Reissner [l 31 the 033 stress was assumed to equal to k0.5q at x3 equal to +h/2. respectively. Thus, Reissner and Mindlin theories have assumed same values for o, at the faces or at x3 equal to +h/2, but Reissner's theory concerned about 033 distribution on the thickness. Mindlin showed [3] that in his theory only the linearlv weighted average effect of 033 was neglected rather than 033 itself with reference to Reissner's theory. When these points are considered it is easy to understand the absence of the distributed load effect in the Mindlin's relation (6). 3 Integral Equations The Weeen's formulation [4] for Reissner's theory can be written as:

4 U, is p, u3 is W, t, is the product Mapa, t3 is the product Q,& and the differentials ds(y) and dr(y) denotes boundary and domain differentials, respectively. Uij represents the rotation Cj=1,2) or the deflection Cj=3) due to a unit point couple (i=1,2) or a unit point force (i=3). 2 I * -~{-[A(z)-B(~)r,~r,p]-;8~~~:z-~)-~r,~r,p] - ZnD I-" With z equal to hr It is necessary to remember that the integrand of the domain integral in equation (8) contains the additional factor from Reissner's theory related to the distributed load (linearly weighted average effect of c ~ that ~ is ~ turned ) null in Mindlin's theory. The following domain integral replaces the domain integral for Reissner's theory in equation (8) to analyze plates using Mindin's hypotheses: r 1 The boundary integral equation for Mindlin's theory written with reference to boundary coordinates ns (normal-tangential) is given by: With Cij equals to Kronecker delta for a smooth boundary, uj is related to the fundamental solution used and it corresponds to the deflection for the solution due to a unit point load (i=3) or the rotation for the solution due to a unit point couple (i=l or 2). 8, and 8, are v, and v,, respectively. The integral equation for classical analysis can be written as: With Cap equals to Kronecker delta for a smooth boundary, up is related to the fundamental solution used and it corresponds to the deflection for the solution due to a unit point load (a=l) or the rotation for the solution due to a unit point couple (a=2). The parameters introduced are the equivalent shear (V,) and a corner reaction (R,) at each corner when polygonal plates are considered.

5 The expression (13) presents the corner reaction (R,) at corner i as the difference between the twisting moments at the corner neighborhood on the forward side (M,:) and the backward side (M,:). The classical analysis can be performed with the fundamental solution due to Danson or Bezine-Stern for a unit point load. A general expression for these solutions is given by: Bezine-Stern's solution is obtained from equation (14) when k is turned null or h is equal to e (the base to which Napierian logarithms are calculated). Danson's solution is obtained when k is equal to 0.5 or h can be turned equal to eo.'. The fundamental solution for a unit couple in the classical analysis is obtained from the derivative of the fundamental solution for a unit point load with respect to the field argument, as it was shown by Timoshenko [l 41. When equation (10) and (l l) are compared, a connection among classical and Mindlin theories can be noted. The boundary integral equation (11) could be obtained fiom equation (10) when classical analysis was considered or 0, and 0, would be equal to -W,, and -W,,, respectively. The other end of the connection can be established when the field decomposition [l] is taken into account in the fundamental solution. Thus, a vector containing the rotations of the plate can be written as [l]: (vl;v2)= (m.,.mj+ (H.~.-q) (15 ) 41 and H represent functions whose components are independent of X, [l]. The obtained functions W, 4 and H for a unit couple F, are given by [l]: F: can be understood as the result from domain integration on a circle containing the Dirac-delta force in the direction a (it is equal to 1) and it was introduced to distinguish each couple effect. [l]. The obtained functions W and 4 for a unit point load are given by [l]: r- --

6 The fimction $ is related to the irrotational field and it can be shown that the solution of H is null due to the radial symmetry of the unit point load problem on an infinite plate. The solutions (16) to (19) can be turned equal to Weeen9s solution but a rigid body motion must be included in (1 8) to get it. On the other hand, the fundamental solution can be written with reference to boundary coordinates ns in order to use (10) and to identify the corrections introduced by the shear deformation effect: a) Solution for a unit point load The bending and twisting moments have similar expressions to those used for the classical theory and their expressions written with reference to coordinates ns are given by: * (I-")&& & The transverse shear defined in eqn (7) can be written with reference to coordinates ns with the following expression (Q,=Q,.n,): The rotations v, and v, (or 8, and OS, respectively) are given by: The main difference with reference to classical theory due to Reissner- Mindlin hypothesis appears in the deflection, expression (18). The first term in that expression corresponds to the deflection obtained from classical hypotheses and the second term corresponds to the shear deformation effect. b) Solution for a unit couple The deflection due to a unit couple in the a direction is similar to that obtained under classical hypotheses and it is given by equation (16). Further, the relation (15) for rotations can be putted into a particular expression because the deflection (W) is -$ in this solution and it can be written in terms of ns as: (v,.%) = (- W,,,.-W.,)+ (H.,.-H,,) (20) The notation presented in expression (20) shows the explicit connection among classical and the Reissner-Mindlin theories. When the expression (20) is introduced in the relations for the transverse shear (7), they can be written as: The distributed shears Qi can be written in terms of boundary coordinates ns: The vector given by expression (2 l) could be used in the relation (20):

7 The expression (22) shows a physical meaning for the correction introduced by Reissner-Mindlin theory. The final expression for the transverse shear Q, due to a unit couple in the a direction is given by: The first term between the square brackets in expression (23) is equal to the transverse shear due to a couple obtained from the classical theory. The second term is the correction due to the Reissner-Mindlin hypotheses. The bending and twisting moments are given by: The moments expressions (24 and 25) contain the classical relation (eqn 1) plus a correction introduced by the shear deformation effect. The deflection. rotations and efforts were written with reference to boundar) coordinates ns at field points and for a unit couple in the a direction at the source point. Appropriate dot products must be employed when one of the boundary directions at the source point is used for the couple direction. As an example, the deflection and the bending moment due to a couple in the direction would be: W!= wa.ila (26) M," Mna.lla (27) Boundary directions at the source point are noted by C and 2 in equations (26, 27). The deflection and the bending moment due to a couple in the direction were noted by W" and M," respectively. The deflection and the bending moment due to a couple in the direction Q were noted by W" and M,", respectively. Thus, theconciusions about the present development can be summarized as: The rotations and efforts obtained from the fundamental solution due to a unit point load with the Reissner-Mindlin theory were similar to those obtained from the classical theory. The shear deformation effect appeared in the deflection as an additional term to correct the classical expression. The deflection obtained from the fundamental solution due to a unit couple with the Reissner-Mindlin theory was similar to that obtained from the classical theory. However, rotations and efforts had the classical expression plus an additional term introduced by the shear deformation effect. The BEM permits that the shear deformation effect can be switched on or off in plate analyses. When the boundary equation (1 1) is used with two boundary unknowns, it would be necessary to introduce an additional unknown because Reissner-Mindlin theory works with three boundary

8 unknowns. In this way, it would be necessary to suppress the unknowns related to corner reactions (R,) because they corresponds to a particular feature of the classical analysis and to return from V,* to Q,* in the boundary parameters. On the other hand. when the equation (10) is used, the soft restraint condition (M,, is released on the boundary) and the fundamental solution according to the classical theory can be employed. The integral equation could be written as: i C 'J' U J + ir(q;.w - b$.w,n-h'(,s.w,s).6 = - Mn.w,b).a+ jjwi.q.& (28) The equation (28) is the alternative way to perform classical analyses, which is similar to studies developed by Mukherjee [9] and Paiva [12]. It could be understood as a weak formulation from plate theories with the shear deformation effect. Thus, the responses would be obtained by an irrotational approach of the plate behavior and the terms related to the shear correction would be disregard. 4 Numerical Example A square plate was analyzed with classical and Reissner-Mindlin theories. The boundary was divided into 40 elements (44 nodes) and double nodes were employed at the corners. All nodal parameters were placed at the ends of the element and when discontinuous boundary elements were used, the collocation points were shifted to inside the element at a distance equal to a quarter of the element length. The classical approach used the equation (1 1) with Danson's fundamental solution for a unit point load. The source points were placed on the boundary and outside the domain in the normal direction of the boundary at a distance from the nodes equals to a quarter of the element length. Reissner's theory used the equation (8) with Weeen's formulation. Mindlin's theory used the equation (10). The responses from Mindlin's theory were labeled by Weeen and Danson when h was equal to nlh and eo", respectively. The source points were placed outside in the same points used for the classical analysis. The plate was loaded by an uniform load equal to 1 ~.m-~, the Young modulus was MPa and the side of the plate had 2 m in length. Table 1 presents the results for a simply supported plate from all sides. The results presented in Table 2 were obtained when the plate had one side clamped and was simply supported from others sides. The responses were obtained at the center of the plate with two kinds of boundary conditions related to the twisting moments: "soft" when the twisting moments were released on the boundary and "hard" when they were restrained. The features presented in Tables 1 and 2 can be summarized as. 0 The differences among results obtained from Reissner and Mindlin theory were less than 1 % for internal points and efforts distribution on the boundary. The result obtained for internal points with "hard condition" were closer to the classical approach than those obtained with the "soft condition", even for the thick plates. On the other hand, the efforts distribution on the boundary with the "soft" condition were closer to the classical approach than those

9 obtained with the "hard" condition. It agrees with Timoshenko's explanation [l41 and the approaches contained when one of the components of the field is employed alone [l]. The use of h equal to eo.' for the irrotational field did not present significant differences in the results from those obtained with h equal to dh. Other boundary conditions are being studied and the results will be reported soon. Table 1 - Simply Supported plate BEM / Soft Table 2 - One edge clamped and simply supported from others edges ' Obtained at the center W l M11 Thickness The author is grateful to FAPESP due to the support for the development of studies on plates. References [l] Palermo Jr., L., (2000). A Study About Fundamental Solution in Plates, BEM 22. Editors C.A. Brebbia, H. Power, [2] Reissner. E., (1945). The Effect of Transverse Shear Deformation on the Bending of Elastic Plates. Jozirnal of Applled ~Mechan~cs, [3] Mindlin, R.D., (195 1). Influence of rotatory inertia and shear on flexural motions of isotropic elastic plates, Journal ofapplled Mechunlcs,

10 Weeen. F., (1982a) Application of the direct boundary element method to Reissner's plate model, Boundary Element Methods in Engineering, Springer- Berlin. Danson, D.J., (1979). Analysis of Plate Bending Problems by Direct Boundary Element Method, Southampton, UK, Dissertation (M. Sc.), University of Southampton, Bezine, G., Gamby, D.A., (1978). A New Integral Equation Formulation for Plate Bending Problems. Recent Advances in Boz4ndar-y Eletnent Method, Pentech Press, London, Stern, M.A. (1979) A general boundary integral formulation for the numerical solution of plate bending problems. Int. J. Solids Struct., v. 15, p ,. Tottenham, H., (1979) The Boundary elements for plates and shells, Development in BEM, Applied Science Publishers,. Guo-Shu, S., Mukherjee, S., (1986) Boundary element method: analysis of bending of elastic plates of arbitrary shape with general boundary conditions, Eng. Anal. Bound Element,. Vilmann, O., Dasgupta, G. (1992) Fundamental solutions of Mindlin plates with variable thickness for stochastic boundary elements, Eng. Analysis with Boundary Elements, v.?, p De Barcellos, C.S., Silva, L.H.M. (1987) A boundary element formulation for the Mindlin's plate model. In: Brebbia, C.A., Venturini, W.S., eds., Boundary Element Tecniques: Applications in Stress Analysis and Heat Transfer: Southampton. Paiva, J.B.. Neto, L.O., (1995) An alternative boundary element formulation for plate bending analysis, International Conference on Boundary Element Technology,. Reissner, E., (1947) On Bending of Elastic Plates, Q. Appl. Math. Timoshenko, S. P,, Woinowsky-Krieger, S., (1959) Theory of Plates and Shells, McGraw-Hill Book Company, New York. Ed. Katsikadelis, J.T. & Yotis, A.J., (1993) A new boundary element solution of thick plates modelled by Reissner's theory, Eng. Anal. Bound. Element..

Department of Structural, Faculty of Civil Engineering, Architecture and Urban Design, State University of Campinas, Brazil

Department of Structural, Faculty of Civil Engineering, Architecture and Urban Design, State University of Campinas, Brazil Blucher Mechanical Engineering Proceedings May 2014, vol. 1, num. 1 www.proceedings.blucher.com.br/evento/10wccm A SIMPLIFIED FORMULATION FOR STRESS AND TRACTION BOUNDARY IN- TEGRAL EQUATIONS USING THE

More information

Transactions on Modelling and Simulation vol 9, 1995 WIT Press, ISSN X

Transactions on Modelling and Simulation vol 9, 1995 WIT Press,  ISSN X An alternative boundary element formulation for plate bending analysis J.B. Paiva, L.O. Neto Structures Department, Sao Carlos Civil Engineering School, f, BrazzY Abstract This work presents an alternative

More information

Transactions on Modelling and Simulation vol 8, 1994 WIT Press, ISSN X

Transactions on Modelling and Simulation vol 8, 1994 WIT Press,   ISSN X Model analysis of plates using the dual reciprocity boundary element method T.W. Davies & F.A. Moslehy Department of Mechanical and Aerospace Engineering, University of Central Florida, Orlando, Florida,

More information

Transactions on Modelling and Simulation vol 12, 1996 WIT Press, ISSN X

Transactions on Modelling and Simulation vol 12, 1996 WIT Press,   ISSN X Plate-soil elastodynamic coupling using analysis S.F.A. Baretto, H.B. Coda, W.S. Venturini Sao Carlos School of Engineering, University ofsao Paulo, Sao Carlos - SP, Brazil BEM Abstract The aim of this

More information

Bending of Simply Supported Isotropic and Composite Laminate Plates

Bending of Simply Supported Isotropic and Composite Laminate Plates Bending of Simply Supported Isotropic and Composite Laminate Plates Ernesto Gutierrez-Miravete 1 Isotropic Plates Consider simply a supported rectangular plate of isotropic material (length a, width b,

More information

Lecture 15 Strain and stress in beams

Lecture 15 Strain and stress in beams Spring, 2019 ME 323 Mechanics of Materials Lecture 15 Strain and stress in beams Reading assignment: 6.1 6.2 News: Instructor: Prof. Marcial Gonzalez Last modified: 1/6/19 9:42:38 PM Beam theory (@ ME

More information

THEORY OF PLATES AND SHELLS

THEORY OF PLATES AND SHELLS THEORY OF PLATES AND SHELLS S. TIMOSHENKO Professor Emeritus of Engineering Mechanics Stanford University S. WOINOWSKY-KRIEGER Professor of Engineering Mechanics Laval University SECOND EDITION MCGRAW-HILL

More information

MIXED RECTANGULAR FINITE ELEMENTS FOR PLATE BENDING

MIXED RECTANGULAR FINITE ELEMENTS FOR PLATE BENDING 144 MIXED RECTANGULAR FINITE ELEMENTS FOR PLATE BENDING J. N. Reddy* and Chen-Shyh-Tsay School of Aerospace, Mechanical and Nuclear Engineering, University of Oklahoma, Norman, Oklahoma The paper describes

More information

COPYRIGHTED MATERIAL. Index

COPYRIGHTED MATERIAL. Index Index A Admissible function, 163 Amplification factor, 36 Amplitude, 1, 22 Amplitude-modulated carrier, 630 Amplitude ratio, 36 Antinodes, 612 Approximate analytical methods, 647 Assumed modes method,

More information

INTERNATIONAL JOURNAL OF CIVIL AND STRUCTURAL ENGINEERING Volume 3, No 4, 2013

INTERNATIONAL JOURNAL OF CIVIL AND STRUCTURAL ENGINEERING Volume 3, No 4, 2013 INTERNATIONAL JOURNAL OF CIVIL AND STRUCTURAL ENGINEERING Volume 3, No 4, 2013 Copyright by the authors - Licensee IPA- Under Creative Commons license 3.0 Research article ISSN 0976 4399 Pure bending analysis

More information

A NEW REFINED THEORY OF PLATES WITH TRANSVERSE SHEAR DEFORMATION FOR MODERATELY THICK AND THICK PLATES

A NEW REFINED THEORY OF PLATES WITH TRANSVERSE SHEAR DEFORMATION FOR MODERATELY THICK AND THICK PLATES A NEW REFINED THEORY OF PLATES WITH TRANSVERSE SHEAR DEFORMATION FOR MODERATELY THICK AND THICK PLATES J.M. MARTÍNEZ VALLE Mechanics Department, EPS; Leonardo da Vinci Building, Rabanales Campus, Cordoba

More information

Bilinear Quadrilateral (Q4): CQUAD4 in GENESIS

Bilinear Quadrilateral (Q4): CQUAD4 in GENESIS Bilinear Quadrilateral (Q4): CQUAD4 in GENESIS The Q4 element has four nodes and eight nodal dof. The shape can be any quadrilateral; we ll concentrate on a rectangle now. The displacement field in terms

More information

CHAPTER THREE SYMMETRIC BENDING OF CIRCLE PLATES

CHAPTER THREE SYMMETRIC BENDING OF CIRCLE PLATES CHAPTER THREE SYMMETRIC BENDING OF CIRCLE PLATES * Governing equations in beam and plate bending ** Solution by superposition 1.1 From Beam Bending to Plate Bending 1.2 Governing Equations For Symmetric

More information

Structural Dynamics Lecture Eleven: Dynamic Response of MDOF Systems: (Chapter 11) By: H. Ahmadian

Structural Dynamics Lecture Eleven: Dynamic Response of MDOF Systems: (Chapter 11) By: H. Ahmadian Structural Dynamics Lecture Eleven: Dynamic Response of MDOF Systems: (Chapter 11) By: H. Ahmadian ahmadian@iust.ac.ir Dynamic Response of MDOF Systems: Mode-Superposition Method Mode-Superposition Method:

More information

FREE VIBRATION ANALYSIS OF THIN CYLINDRICAL SHELLS SUBJECTED TO INTERNAL PRESSURE AND FINITE ELEMENT ANALYSIS

FREE VIBRATION ANALYSIS OF THIN CYLINDRICAL SHELLS SUBJECTED TO INTERNAL PRESSURE AND FINITE ELEMENT ANALYSIS FREE VIBRATION ANALYSIS OF THIN CYLINDRICAL SHELLS SUBJECTED TO INTERNAL PRESSURE AND FINITE ELEMENT ANALYSIS J. Kandasamy 1, M. Madhavi 2, N. Haritha 3 1 Corresponding author Department of Mechanical

More information

Finite Element Analysis Prof. Dr. B. N. Rao Department of Civil Engineering Indian Institute of Technology, Madras. Module - 01 Lecture - 11

Finite Element Analysis Prof. Dr. B. N. Rao Department of Civil Engineering Indian Institute of Technology, Madras. Module - 01 Lecture - 11 Finite Element Analysis Prof. Dr. B. N. Rao Department of Civil Engineering Indian Institute of Technology, Madras Module - 01 Lecture - 11 Last class, what we did is, we looked at a method called superposition

More information

An alternative multi-region BEM technique for layered soil problems

An alternative multi-region BEM technique for layered soil problems An alternative multi-region BM technique for layered soil problems D.B. Ribeiro & J.B. Paiva Structural ngineering Department, São Carlos ngineering School, University of São Paulo, Brazil. Abstract Different

More information

Analytical Strip Method for Thin Isotropic Cylindrical Shells

Analytical Strip Method for Thin Isotropic Cylindrical Shells IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 14, Issue 4 Ver. III (Jul. Aug. 2017), PP 24-38 www.iosrjournals.org Analytical Strip Method for

More information

Presented By: EAS 6939 Aerospace Structural Composites

Presented By: EAS 6939 Aerospace Structural Composites A Beam Theory for Laminated Composites and Application to Torsion Problems Dr. BhavaniV. Sankar Presented By: Sameer Luthra EAS 6939 Aerospace Structural Composites 1 Introduction Composite beams have

More information

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich UNIVERSITY OF SASKATCHEWAN ME 313.3 MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS For Marker s Use Only LAST NAME (printed): FIRST

More information

Chapter 12 Plate Bending Elements. Chapter 12 Plate Bending Elements

Chapter 12 Plate Bending Elements. Chapter 12 Plate Bending Elements CIVL 7/8117 Chapter 12 - Plate Bending Elements 1/34 Chapter 12 Plate Bending Elements Learning Objectives To introduce basic concepts of plate bending. To derive a common plate bending element stiffness

More information

Table of Contents. Preface... 13

Table of Contents. Preface... 13 Table of Contents Preface... 13 Chapter 1. Vibrations of Continuous Elastic Solid Media... 17 1.1. Objective of the chapter... 17 1.2. Equations of motion and boundary conditions of continuous media...

More information

The problem of isotropic rectangular plate with four clamped edges

The problem of isotropic rectangular plate with four clamped edges Sādhanā Vol. 32, Part 3, June 2007, pp. 181 186. Printed in India The problem of isotropic rectangular plate with four clamped edges C ERDEM İMRAK and ISMAIL GERDEMELI Istanbul Technical University, Faculty

More information

Influence of Chebyshev Collocation Points on the Convergence of Results in the Analysis of Annular Plate Vibrations

Influence of Chebyshev Collocation Points on the Convergence of Results in the Analysis of Annular Plate Vibrations Tamkang Journal of Science and Engineering, Vol. 8, No 1, pp. 57 62 (2005) 57 Influence of Chebyshev Collocation Points on the Convergence of Results in the Analysis of Annular Plate Vibrations R. P. Singh

More information

7.4 The Elementary Beam Theory

7.4 The Elementary Beam Theory 7.4 The Elementary Beam Theory In this section, problems involving long and slender beams are addressed. s with pressure vessels, the geometry of the beam, and the specific type of loading which will be

More information

Computable representations of influence functions for multiply connected Kirchoff plates

Computable representations of influence functions for multiply connected Kirchoff plates Computable representations of influence functions for multiply connected Kirchoff plates Y.A. Melnikov Department of Mathematical Sciences Middle Tennessee State University, USA Abstract A modification

More information

EFFECT OF RETROFITTING ON FLEXURAL RIGIDITY OF RECTANGULAR FRP PLATES

EFFECT OF RETROFITTING ON FLEXURAL RIGIDITY OF RECTANGULAR FRP PLATES EFFECT OF RETROFITTING ON FLEXURAL RIGIDITY OF RECTANGULAR FRP PLATES STEVEN J. MAKONIS, JR. Department of Civil & Environmental Engineering Old Dominion University Norfolk, VA 23528-0241, USA smako001@odu.edu

More information

Elastic plastic bending of stepped annular plates

Elastic plastic bending of stepped annular plates Applications of Mathematics and Computer Engineering Elastic plastic bending of stepped annular plates JAAN LELLEP University of Tartu Institute of Mathematics J. Liivi Street, 549 Tartu ESTONIA jaan.lellep@ut.ee

More information

A *69>H>N6 #DJGC6A DG C<>C::G>C<,8>:C8:H /DA 'D 2:6G - ( - ) +"' ( + -"( (' (& -+" % '('%"' +"-2 ( -!"',- % )% -.C>K:GH>IN D; AF69>HH>6,-+

A *69>H>N6 #DJGC6A DG C<>C::G>C<,8>:C8:H /DA 'D 2:6G - ( - ) +' ( + -( (' (& -+ % '('%' +-2 ( -!',- % )% -.C>K:GH>IN D; AF69>HH>6,-+ The primary objective is to determine whether the structural efficiency of plates can be improved with variable thickness The large displacement analysis of steel plate with variable thickness at direction

More information

Stability of Simply Supported Square Plate with Concentric Cutout

Stability of Simply Supported Square Plate with Concentric Cutout International OPEN ACCESS Journal Of Modern Engineering Research (IJMER) Stability of Simply Supported Square Plate with Concentric Cutout Jayashankarbabu B. S. 1, Dr. Karisiddappa 1 (Civil Engineering

More information

Analysis of Axially Loaded Non-prismatic Beams with General End Restraints Using Differential Quadrature Method

Analysis of Axially Loaded Non-prismatic Beams with General End Restraints Using Differential Quadrature Method ISBN 978-93-84422-56-1 Proceedings of International Conference on Architecture, Structure and Civil Engineering (ICASCE'15 Antalya (Turkey Sept. 7-8, 2015 pp. 1-7 Analysis of Axially Loaded Non-prismatic

More information

CHAPTER -6- BENDING Part -1-

CHAPTER -6- BENDING Part -1- Ishik University / Sulaimani Civil Engineering Department Mechanics of Materials CE 211 CHAPTER -6- BENDING Part -1-1 CHAPTER -6- Bending Outlines of this chapter: 6.1. Chapter Objectives 6.2. Shear and

More information

FLEXIBILITY METHOD FOR INDETERMINATE FRAMES

FLEXIBILITY METHOD FOR INDETERMINATE FRAMES UNIT - I FLEXIBILITY METHOD FOR INDETERMINATE FRAMES 1. What is meant by indeterminate structures? Structures that do not satisfy the conditions of equilibrium are called indeterminate structure. These

More information

Numerical Solution of Non-Linear Biharmonic. Equation for Elasto-Plastic Bending Plate

Numerical Solution of Non-Linear Biharmonic. Equation for Elasto-Plastic Bending Plate Applied Mathematical Sciences, Vol. 9, 5, no. 6, 769-78 HIKARI Ltd, www.m-hikari.com http://dx.doi.org/.988/ams.5.575 Numerical Solution of Non-Linear Biharmonic Equation for Elasto-Plastic Bending Plate

More information

AN ALTERNATIVE TECHNIQUE FOR TANGENTIAL STRESS CALCULATION IN DISCONTINUOUS BOUNDARY ELEMENTS

AN ALTERNATIVE TECHNIQUE FOR TANGENTIAL STRESS CALCULATION IN DISCONTINUOUS BOUNDARY ELEMENTS th Pan-American Congress of Applied Mechanics January 04-08, 00, Foz do Iguaçu, PR, Brazil AN ALTERNATIVE TECHNIQUE FOR TANGENTIAL STRESS CALCULATION IN DISCONTINUOUS BOUNDARY ELEMENTS Otávio Augusto Alves

More information

First-Order Solutions for the Buckling Loads of Euler-Bernoulli Weakened Columns

First-Order Solutions for the Buckling Loads of Euler-Bernoulli Weakened Columns First-Order Solutions for the Buckling Loads of Euler-Bernoulli Weakened Columns J. A. Loya ; G. Vadillo 2 ; and J. Fernández-Sáez 3 Abstract: In this work, closed-form expressions for the buckling loads

More information

Application of Finite Element Method to Create Animated Simulation of Beam Analysis for the Course of Mechanics of Materials

Application of Finite Element Method to Create Animated Simulation of Beam Analysis for the Course of Mechanics of Materials International Conference on Engineering Education and Research "Progress Through Partnership" 4 VSB-TUO, Ostrava, ISSN 156-35 Application of Finite Element Method to Create Animated Simulation of Beam

More information

Flexure of Thick Cantilever Beam using Third Order Shear Deformation Theory

Flexure of Thick Cantilever Beam using Third Order Shear Deformation Theory International Journal of Engineering Research and Development e-issn: 78-67X, p-issn: 78-8X, www.ijerd.com Volume 6, Issue 1 (April 13), PP. 9-14 Fleure of Thick Cantilever Beam using Third Order Shear

More information

Calculation of Shear Areas and Torsional Constant using the Boundary Element Method with Scada Pro Software

Calculation of Shear Areas and Torsional Constant using the Boundary Element Method with Scada Pro Software NATIONAL TECHNICAL UNIVERSITY OF ATHENS School of Civil Engineering Institute of Structural Analysis & Antiseismic Research Dr. Sapountakis J. Evangelos Dr. Civil Engineer NTUA Professor NTUA Calculation

More information

CRITERIA FOR SELECTION OF FEM MODELS.

CRITERIA FOR SELECTION OF FEM MODELS. CRITERIA FOR SELECTION OF FEM MODELS. Prof. P. C.Vasani,Applied Mechanics Department, L. D. College of Engineering,Ahmedabad- 380015 Ph.(079) 7486320 [R] E-mail:pcv-im@eth.net 1. Criteria for Convergence.

More information

Using MATLAB and. Abaqus. Finite Element Analysis. Introduction to. Amar Khennane. Taylor & Francis Croup. Taylor & Francis Croup,

Using MATLAB and. Abaqus. Finite Element Analysis. Introduction to. Amar Khennane. Taylor & Francis Croup. Taylor & Francis Croup, Introduction to Finite Element Analysis Using MATLAB and Abaqus Amar Khennane Taylor & Francis Croup Boca Raton London New York CRC Press is an imprint of the Taylor & Francis Croup, an informa business

More information

Nonlinear bending analysis of laminated composite stiffened plates

Nonlinear bending analysis of laminated composite stiffened plates Nonlinear bending analysis of laminated composite stiffened plates * S.N.Patel 1) 1) Dept. of Civi Engineering, BITS Pilani, Pilani Campus, Pilani-333031, (Raj), India 1) shuvendu@pilani.bits-pilani.ac.in

More information

Pune, Maharashtra, India

Pune, Maharashtra, India Volume 6, Issue 6, May 17, ISSN: 78 7798 STATIC FLEXURAL ANALYSIS OF THICK BEAM BY HYPERBOLIC SHEAR DEFORMATION THEORY Darakh P. G. 1, Dr. Bajad M. N. 1 P.G. Student, Dept. Of Civil Engineering, Sinhgad

More information

Advanced Structural Analysis EGF Section Properties and Bending

Advanced Structural Analysis EGF Section Properties and Bending Advanced Structural Analysis EGF316 3. Section Properties and Bending 3.1 Loads in beams When we analyse beams, we need to consider various types of loads acting on them, for example, axial forces, shear

More information

Transactions on Modelling and Simulation vol 18, 1997 WIT Press, ISSN X

Transactions on Modelling and Simulation vol 18, 1997 WIT Press,   ISSN X An integral equation formulation of the coupled vibrations of uniform Timoshenko beams Masa. Tanaka & A. N. Bercin Department of Mechanical Systems Engineering, Shinshu University 500 Wakasato, Nagano

More information

Kirchhoff Plates: Field Equations

Kirchhoff Plates: Field Equations 20 Kirchhoff Plates: Field Equations AFEM Ch 20 Slide 1 Plate Structures A plate is a three dimensional bod characterized b Thinness: one of the plate dimensions, the thickness, is much smaller than the

More information

A HIGHER-ORDER BEAM THEORY FOR COMPOSITE BOX BEAMS

A HIGHER-ORDER BEAM THEORY FOR COMPOSITE BOX BEAMS A HIGHER-ORDER BEAM THEORY FOR COMPOSITE BOX BEAMS A. Kroker, W. Becker TU Darmstadt, Department of Mechanical Engineering, Chair of Structural Mechanics Hochschulstr. 1, D-64289 Darmstadt, Germany kroker@mechanik.tu-darmstadt.de,

More information

FORMULA FOR FORCED VIBRATION ANALYSIS OF STRUCTURES USING STATIC FACTORED RESPONSE AS EQUIVALENT DYNAMIC RESPONSE

FORMULA FOR FORCED VIBRATION ANALYSIS OF STRUCTURES USING STATIC FACTORED RESPONSE AS EQUIVALENT DYNAMIC RESPONSE FORMULA FOR FORCED VIBRATION ANALYSIS OF STRUCTURES USING STATIC FACTORED RESPONSE AS EQUIVALENT DYNAMIC RESPONSE ABSTRACT By G. C. Ezeokpube, M. Eng. Department of Civil Engineering Anambra State University,

More information

Module 3 : Equilibrium of rods and plates Lecture 15 : Torsion of rods. The Lecture Contains: Torsion of Rods. Torsional Energy

Module 3 : Equilibrium of rods and plates Lecture 15 : Torsion of rods. The Lecture Contains: Torsion of Rods. Torsional Energy The Lecture Contains: Torsion of Rods Torsional Energy This lecture is adopted from the following book 1. Theory of Elasticity, 3 rd edition by Landau and Lifshitz. Course of Theoretical Physics, vol-7

More information

The Finite Element Method for Solid and Structural Mechanics

The Finite Element Method for Solid and Structural Mechanics The Finite Element Method for Solid and Structural Mechanics Sixth edition O.C. Zienkiewicz, CBE, FRS UNESCO Professor of Numerical Methods in Engineering International Centre for Numerical Methods in

More information

Abstract. 1 Introduction

Abstract. 1 Introduction A numerical approach for the free vibration of isotropic triangular plates J.P. Arenas Institute ofacoustics, Facultad de Ciencias de la Ingenieria, Universidad Austral de Chile, PO Box 567, Valdivia,

More information

AN INTEGRATED KIRCHHOFF PLATE ELEMENT BY GALERKIN METHOD FOR THE ANALYSIS OF PLATES ON ELASTIC FOUNDATION

AN INTEGRATED KIRCHHOFF PLATE ELEMENT BY GALERKIN METHOD FOR THE ANALYSIS OF PLATES ON ELASTIC FOUNDATION AN INTEGRATED IRCHHOFF PLATE ELEMENT BY GALERIN METHOD FOR THE ANALYSIS OF PLATES ON ELASTIC FOUNDATION Ragesh.P.P, V.Mustafa 2, T.P.Somasundaran 3 (Research Scholar, National Institute of Technology Calicut,

More information

MECHANICS OF MATERIALS

MECHANICS OF MATERIALS STATICS AND MECHANICS OF MATERIALS Ferdinand P. Beer E. Russell Johnston, Jr, John T. DeWolf David E Mazurek \Cawect Mc / iur/» Craw SugomcT Hilt Introduction 1 1.1 What is Mechanics? 2 1.2 Fundamental

More information

NONCLASSICAL MODELS IN THE SHELL THEORY WITH APPLICATIONS TO MULTILAYERED NANOTUBES

NONCLASSICAL MODELS IN THE SHELL THEORY WITH APPLICATIONS TO MULTILAYERED NANOTUBES COMPDYN 0 3 rd ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering M. Papadrakakis M. Fragiadakis V. Plevris eds. Corfu Greece 5-8 May 0 NONCLASSICAL

More information

P. M. Pankade 1, D. H. Tupe 2, G. R. Gandhe 3

P. M. Pankade 1, D. H. Tupe 2, G. R. Gandhe 3 ISSN: 78 7798 Volume 5, Issue 5, May 6 Static Fleural Analysis of Thick Beam Using Hyperbolic Shear Deformation Theory P. M. Pankade, D. H. Tupe, G. R. Gandhe P.G. Student, Dept. of Civil Engineering,

More information

Finite Element Analysis Prof. Dr. B. N. Rao Department of Civil Engineering Indian Institute of Technology, Madras. Module - 01 Lecture - 13

Finite Element Analysis Prof. Dr. B. N. Rao Department of Civil Engineering Indian Institute of Technology, Madras. Module - 01 Lecture - 13 Finite Element Analysis Prof. Dr. B. N. Rao Department of Civil Engineering Indian Institute of Technology, Madras (Refer Slide Time: 00:25) Module - 01 Lecture - 13 In the last class, we have seen how

More information

Forced Vibration Analysis of Timoshenko Beam with Discontinuities by Means of Distributions Jiri Sobotka

Forced Vibration Analysis of Timoshenko Beam with Discontinuities by Means of Distributions Jiri Sobotka 21 st International Conference ENGINEERING MECHANICS 2015 Svratka, Czech Republic, May 11 14, 2015 Full Text Paper #018, pp. 45 51 Forced Vibration Analysis of Timoshenko Beam with Discontinuities by Means

More information

Chapter 3. Load and Stress Analysis

Chapter 3. Load and Stress Analysis Chapter 3 Load and Stress Analysis 2 Shear Force and Bending Moments in Beams Internal shear force V & bending moment M must ensure equilibrium Fig. 3 2 Sign Conventions for Bending and Shear Fig. 3 3

More information

Dynamic and buckling analysis of FRP portal frames using a locking-free finite element

Dynamic and buckling analysis of FRP portal frames using a locking-free finite element Fourth International Conference on FRP Composites in Civil Engineering (CICE8) 22-24July 8, Zurich, Switzerland Dynamic and buckling analysis of FRP portal frames using a locking-free finite element F.

More information

Simulation of Geometrical Cross-Section for Practical Purposes

Simulation of Geometrical Cross-Section for Practical Purposes Simulation of Geometrical Cross-Section for Practical Purposes Bhasker R.S. 1, Prasad R. K. 2, Kumar V. 3, Prasad P. 4 123 Department of Mechanical Engineering, R.D. Engineering College, Ghaziabad, UP,

More information

Module 4 : Deflection of Structures Lecture 4 : Strain Energy Method

Module 4 : Deflection of Structures Lecture 4 : Strain Energy Method Module 4 : Deflection of Structures Lecture 4 : Strain Energy Method Objectives In this course you will learn the following Deflection by strain energy method. Evaluation of strain energy in member under

More information

Free vibrations of a multi-span Timoshenko beam carrying multiple spring-mass systems

Free vibrations of a multi-span Timoshenko beam carrying multiple spring-mass systems Sādhanā Vol. 33, Part 4, August 2008, pp. 385 401. Printed in India Free vibrations of a multi-span Timoshenko beam carrying multiple spring-mass systems YUSUF YESILCE 1, OKTAY DEMIRDAG 2 and SEVAL CATAL

More information

VIBRATION ANALYSIS OF EULER AND TIMOSHENKO BEAMS USING DIFFERENTIAL TRANSFORMATION METHOD

VIBRATION ANALYSIS OF EULER AND TIMOSHENKO BEAMS USING DIFFERENTIAL TRANSFORMATION METHOD VIBRATION ANALYSIS OF EULER AND TIMOSHENKO BEAMS USING DIFFERENTIAL TRANSFORMATION METHOD Dona Varghese 1, M.G Rajendran 2 1 P G student, School of Civil Engineering, 2 Professor, School of Civil Engineering

More information

Level 7 Postgraduate Diploma in Engineering Computational mechanics using finite element method

Level 7 Postgraduate Diploma in Engineering Computational mechanics using finite element method 9210-203 Level 7 Postgraduate Diploma in Engineering Computational mechanics using finite element method You should have the following for this examination one answer book No additional data is attached

More information

The Interaction between a Uniformly Loaded Circular Plate and an Isotropic Elastic Halfspace: A Variational Approach

The Interaction between a Uniformly Loaded Circular Plate and an Isotropic Elastic Halfspace: A Variational Approach 1. STRUCT. MECH., 7(3), 231-246 (1979) The Interaction between a Uniformly Loaded Circular Plate and an Isotropic Elastic Halfspace: A Variational Approach A. P. S. Selvedurai ABSTRACT The axially symmetric

More information

COMPOSITE PLATE THEORIES

COMPOSITE PLATE THEORIES CHAPTER2 COMPOSITE PLATE THEORIES 2.1 GENERAL Analysis of composite plates is usually done based on one of the following the ries. 1. Equivalent single-layer theories a. Classical laminate theory b. Shear

More information

Effect of Specimen Dimensions on Flexural Modulus in a 3-Point Bending Test

Effect of Specimen Dimensions on Flexural Modulus in a 3-Point Bending Test Effect of Specimen Dimensions on Flexural Modulus in a 3-Point Bending Test M. Praveen Kumar 1 and V. Balakrishna Murthy 2* 1 Mechanical Engineering Department, P.V.P. Siddhartha Institute of Technology,

More information

EVALUATION OF MODULUS OF RIGIDITY BY DYNAMIC PLATE SHEAR TESTING Tetsuya Nakao. and Takeshi Okano

EVALUATION OF MODULUS OF RIGIDITY BY DYNAMIC PLATE SHEAR TESTING Tetsuya Nakao. and Takeshi Okano EVALUATION OF MODULUS OF RIGIDITY BY DYNAMIC PLATE SHEAR TESTING Tetsuya Nakao Graduate Student Present address: Department of Forestry Faculty of Agriculture Shimane University Matsue 690, Japan and Takeshi

More information

6. Bending CHAPTER OBJECTIVES

6. Bending CHAPTER OBJECTIVES CHAPTER OBJECTIVES Determine stress in members caused by bending Discuss how to establish shear and moment diagrams for a beam or shaft Determine largest shear and moment in a member, and specify where

More information

IN-PLANE VIBRATIONS OF CIRCULAR CURVED BEAMS WITH A TRANSVERSE OPEN CRACK 1. INTRODUCTION

IN-PLANE VIBRATIONS OF CIRCULAR CURVED BEAMS WITH A TRANSVERSE OPEN CRACK 1. INTRODUCTION Mathematical and Computational Applications, Vol. 11, No. 1, pp. 1-10, 006. Association for Scientific Research IN-PLANE VIBRATIONS OF CIRCULAR CURVED BEAMS WITH A TRANSVERSE OPEN CRACK Department of Mechanical

More information

INSTABILITY OF AXIALLY COMPRESSED CCCC THIN RECTANGULAR PLATE USING TAYLOR-MCLAURIN S SERIES SHAPE FUNCTION ON RITZ METHOD

INSTABILITY OF AXIALLY COMPRESSED CCCC THIN RECTANGULAR PLATE USING TAYLOR-MCLAURIN S SERIES SHAPE FUNCTION ON RITZ METHOD ISSN-L: 2223-9553, ISSN: 2223-9944 Academic Research International INSTABILITY OF AXIALLY COMPRESSED CCCC THIN RECTANGULAR PLATE USING TAYLOR-MCLAURIN S SERIES SHAPE FUNCTION ON RITZ METHOD O. M. Ibearugbulem

More information

Quintic beam closed form matrices (revised 2/21, 2/23/12) General elastic beam with an elastic foundation

Quintic beam closed form matrices (revised 2/21, 2/23/12) General elastic beam with an elastic foundation General elastic beam with an elastic foundation Figure 1 shows a beam-column on an elastic foundation. The beam is connected to a continuous series of foundation springs. The other end of the foundation

More information

STRESSES WITHIN CURVED LAMINATED BEAMS OF DOUGLAS-FIR

STRESSES WITHIN CURVED LAMINATED BEAMS OF DOUGLAS-FIR UNITED STATES DEPARTMENT OF AGRICULTURE. FOREST SERVICE - FOREST PRODUCTS LABORATORY - MADISON, WIS. STRESSES WITHIN CURVED LAMINATED BEAMS OF DOUGLAS-FIR NOVEMBER 1963 FPL-020 STRESSES WITHIN CURVED LAMINATED

More information

Bending Analysis of Symmetrically Laminated Plates

Bending Analysis of Symmetrically Laminated Plates Leonardo Journal of Sciences ISSN 1583-0233 Issue 16, January-June 2010 p. 105-116 Bending Analysis of Symmetrically Laminated Plates Bouazza MOKHTAR 1, Hammadi FODIL 2 and Khadir MOSTAPHA 2 1 Department

More information

202 Index. failure, 26 field equation, 122 force, 1

202 Index. failure, 26 field equation, 122 force, 1 Index acceleration, 12, 161 admissible function, 155 admissible stress, 32 Airy's stress function, 122, 124 d'alembert's principle, 165, 167, 177 amplitude, 171 analogy, 76 anisotropic material, 20 aperiodic

More information

TRANSIENT RESPONSE OF SANDWICH AND LAMINATED COMPOSITES WITH DAMPING UNDER IMPULSE LOADING

TRANSIENT RESPONSE OF SANDWICH AND LAMINATED COMPOSITES WITH DAMPING UNDER IMPULSE LOADING TRANSIENT RESPONSE OF SANDWICH AND LAMINATED COMPOSITES WITH DAMPING UNDER IMPULSE LOADING Evgeny Barkanov, Andris Chate and Rolands Rikards Institute of Computer Analysis of Structures, Riga Technical

More information

The stiffness of plates

The stiffness of plates The stiffness of plates 1. Introduction The word plate is a collective term for elements in which forces can be transferred in two directions. Floors, walls, bridge slabs and laminates are all plates.

More information

ACCURATE MODELLING OF STRAIN DISCONTINUITIES IN BEAMS USING AN XFEM APPROACH

ACCURATE MODELLING OF STRAIN DISCONTINUITIES IN BEAMS USING AN XFEM APPROACH VI International Conference on Adaptive Modeling and Simulation ADMOS 213 J. P. Moitinho de Almeida, P. Díez, C. Tiago and N. Parés (Eds) ACCURATE MODELLING OF STRAIN DISCONTINUITIES IN BEAMS USING AN

More information

ACCURATE FREE VIBRATION ANALYSIS OF POINT SUPPORTED MINDLIN PLATES BY THE SUPERPOSITION METHOD

ACCURATE FREE VIBRATION ANALYSIS OF POINT SUPPORTED MINDLIN PLATES BY THE SUPERPOSITION METHOD Journal of Sound and Vibration (1999) 219(2), 265 277 Article No. jsvi.1998.1874, available online at http://www.idealibrary.com.on ACCURATE FREE VIBRATION ANALYSIS OF POINT SUPPORTED MINDLIN PLATES BY

More information

INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY

INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY A PATH FOR HORIZING YOUR INNOVATIVE WORK SPECIAL ISSUE FOR INTERNATIONAL LEVEL CONFERENCE "ADVANCES IN SCIENCE, TECHNOLOGY

More information

APPLICATION OF THE GALERKIN-VLASOV METHOD TO THE FLEXURAL ANALYSIS OF SIMPLY SUPPORTED RECTANGULAR KIRCHHOFF PLATES UNDER UNIFORM LOADS

APPLICATION OF THE GALERKIN-VLASOV METHOD TO THE FLEXURAL ANALYSIS OF SIMPLY SUPPORTED RECTANGULAR KIRCHHOFF PLATES UNDER UNIFORM LOADS Nigerian Journal of Technology (NIJOTECH) Vol. 35, No. 4, October 2016, pp. 732 738 Copyright Faculty of Engineering, University of Nigeria, Nsukka, Print ISSN: 0331-8443, Electronic ISSN: 2467-8821 www.nijotech.com

More information

MITOCW MITRES2_002S10linear_lec07_300k-mp4

MITOCW MITRES2_002S10linear_lec07_300k-mp4 MITOCW MITRES2_002S10linear_lec07_300k-mp4 The following content is provided under a Creative Commons license. Your support will help MIT OpenCourseWare continue to offer high quality educational resources

More information

Effect of Rotatory Inertia and Load Natural. Frequency on the Response of Uniform Rayleigh. Beam Resting on Pasternak Foundation

Effect of Rotatory Inertia and Load Natural. Frequency on the Response of Uniform Rayleigh. Beam Resting on Pasternak Foundation Applied Mathematical Sciences, Vol. 12, 218, no. 16, 783-795 HIKARI Ltd www.m-hikari.com https://doi.org/1.12988/ams.218.8345 Effect of Rotatory Inertia and Load Natural Frequency on the Response of Uniform

More information

Example 37 - Analytical Beam

Example 37 - Analytical Beam Example 37 - Analytical Beam Summary This example deals with the use of RADIOSS linear and nonlinear solvers. A beam submitted to a concentrated load on one extremity and fixed on the other hand is studied.

More information

MFS with RBF for Thin Plate Bending Problems on Elastic Foundation

MFS with RBF for Thin Plate Bending Problems on Elastic Foundation MFS with RBF for Thin Plate Bending Problems on Elastic Foundation Qing-Hua Qin, Hui Wang and V. Kompis Abstract In this chapter a meshless method, based on the method of fundamental solutions (MFS and

More information

CHAPTER 5. Beam Theory

CHAPTER 5. Beam Theory CHPTER 5. Beam Theory SangJoon Shin School of Mechanical and erospace Engineering Seoul National University ctive eroelasticity and Rotorcraft Lab. 5. The Euler-Bernoulli assumptions One of its dimensions

More information

Development DKMQ Shell Element with Five Degrees of Freedom per Nodal

Development DKMQ Shell Element with Five Degrees of Freedom per Nodal International Journal of Mechanical Engineering and Robotics Research Vol. 6, No., May 7 Development DKMQ Shell Element with Five Degrees of Freedom per Nodal Herry Irpanni, Irwan Katili, and Imam J. Maknun

More information

PURE BENDING. If a simply supported beam carries two point loads of 10 kn as shown in the following figure, pure bending occurs at segment BC.

PURE BENDING. If a simply supported beam carries two point loads of 10 kn as shown in the following figure, pure bending occurs at segment BC. BENDING STRESS The effect of a bending moment applied to a cross-section of a beam is to induce a state of stress across that section. These stresses are known as bending stresses and they act normally

More information

BEAM DEFLECTION THE ELASTIC CURVE

BEAM DEFLECTION THE ELASTIC CURVE BEAM DEFLECTION Samantha Ramirez THE ELASTIC CURVE The deflection diagram of the longitudinal axis that passes through the centroid of each cross-sectional area of a beam. Supports that apply a moment

More information

MODELING SLAB-COLUMN CONNECTIONS REINFORCED WITH GFRP UNDER LOCALIZED IMPACT

MODELING SLAB-COLUMN CONNECTIONS REINFORCED WITH GFRP UNDER LOCALIZED IMPACT MODELING SLAB-COLUMN CONNECTIONS REINFORCED WITH GFRP UNDER LOCALIZED IMPACT QI ZHANG and AMGAD HUSSEIN Faculty of Engineering, Memorial University of Newfoundland St. John s, Newfoundland, Canada, A1B

More information

Bending Analysis of a Cantilever Nanobeam With End Forces by Laplace Transform

Bending Analysis of a Cantilever Nanobeam With End Forces by Laplace Transform International Journal of Engineering & Applied Sciences (IJEAS) Vol.9, Issue (Special Issue: Composite Structures) (07) 03- http://.doi.org/0.407/ijeas.34635 Int J Eng Appl Sci 9() (07) 03- Bending Analysis

More information

PLAT DAN CANGKANG (TKS 4219)

PLAT DAN CANGKANG (TKS 4219) PLAT DAN CANGKANG (TKS 4219) SESI I: PLATES Dr.Eng. Achfas Zacoeb Dept. of Civil Engineering Brawijaya University INTRODUCTION Plates are straight, plane, two-dimensional structural components of which

More information

MECHANICS OF MATERIALS

MECHANICS OF MATERIALS 2009 The McGraw-Hill Companies, Inc. All rights reserved. Fifth SI Edition CHAPTER 3 MECHANICS OF MATERIALS Ferdinand P. Beer E. Russell Johnston, Jr. John T. DeWolf David F. Mazurek Torsion Lecture Notes:

More information

Optimum Height of Plate Stiffener under Pressure Effect

Optimum Height of Plate Stiffener under Pressure Effect The st Regional Conference of Eng. Sci. NUCEJ Spatial ISSUE vol., No.3, 8 pp 459-468 Optimum Height of Plate Stiffener under Pressure Effect Mazin Victor Yousif M.Sc Production Engineering University of

More information

Finite Difference Dynamic Analysis of Railway Bridges Supported by Pasternak Foundation under Uniform Partially Distributed Moving Railway Vehicle

Finite Difference Dynamic Analysis of Railway Bridges Supported by Pasternak Foundation under Uniform Partially Distributed Moving Railway Vehicle , October 21-23, 2015, San Francisco, USA Finite Difference Dynamic Analysis of Railway Bridges Supported by Pasternak Foundation under Uniform Partially Distributed Moving Railway Vehicle M. C. Agarana

More information

Laminated Beams of Isotropic or Orthotropic Materials Subjected to Temperature Change

Laminated Beams of Isotropic or Orthotropic Materials Subjected to Temperature Change United States Department of Agriculture Forest Service Forest Products Laboratory Research Paper FPL 375 June 1980 Laminated Beams of Isotropic or Orthotropic Materials Subjected to Temperature Change

More information

Analysis of Thick Cantilever Beam Using New Hyperbolic Shear Deformation Theory

Analysis of Thick Cantilever Beam Using New Hyperbolic Shear Deformation Theory International Journal of Research in Advent Technology, Vol.4, No.5, May 16 E-ISSN: 1-967 Analysis of Thick Cantilever Beam Using New Hyperbolic Shear Deformation Theory Mr. Mithun. K. Sawant 1, Dr. Ajay.

More information

Chapter 3. Load and Stress Analysis. Lecture Slides

Chapter 3. Load and Stress Analysis. Lecture Slides Lecture Slides Chapter 3 Load and Stress Analysis 2015 by McGraw Hill Education. This is proprietary material solely for authorized instructor use. Not authorized for sale or distribution in any manner.

More information

Macaulay s method for a Timoshenko beam

Macaulay s method for a Timoshenko beam Macaulay s method for a Timoshenko beam N. G. Stephen School of Engineering Sciences, Mechanical Engineering, University of Southampton, Highfield, Southampton SO7 BJ, UK E-mail: ngs@soton.ac.uk Abstract

More information

Stresses and Strains in flexible Pavements

Stresses and Strains in flexible Pavements Stresses and Strains in flexible Pavements Multi Layered Elastic System Assumptions in Multi Layered Elastic Systems The material properties of each layer are homogeneous property at point A i is the same

More information