EE 230 Lecture 20. Nonlinear Op Amp Applications. The Comparator Nonlinear Analysis Methods

Transcription

1 EE 230 Lecture 20 Nonlinear Op Amp Applications The Comparator Nonlinear Analysis Methods

2 Quiz 14 What is the major purpose of compensation when designing an operatinal amplifier?

3 And the number is? ? 6 9 7

4 Quiz 14 What is the major purpose of compensation when designing an operatinal amplifier? Compensation is used to make the frequency response of an operational amplifier approximately first-order

5 Review from Last Lecture Offset oltage Consider a basic noninverting voltage amplifier OUT A = =1+ RF R If offset voltages are present By superposition, it readily follows that R R F = 1+ + OUT R R F 1+ OS F = 1+ OUT,OFFSET OS If the desired voltage gain is large, the effects of OS are a major problem R R

6 Review from Last Lecture Management of OS with Capacitor Coupling Effects can be reduced even further with a second blocking capacitor R F1 R F2 R OS2 OS1 R OUT R R R R R R F1 F2 F2 = OUT, OFFSET OS1 OS2 R R F2 = 1+ OUT, OFFSET OS2 = OUT, OFFSET OS2

7 Review from Last Lecture Bias and Offset Currents I BIAS is the current that must flow for the internal transistors to operate correctly I BIAS is small for bipolar input op amps, extremely small for FET input op amps Can be neglected in most designs regardless of whether FET or Bipolar input I =I -I OFSET BIAS1 BIAS2 is significantly smaller (/5 to /20) I OFFSET is a random variable with zero mean for most designs I BIAS around 50 na for 741, I OFFSET around 3nA I BIAS around 20 fa for LMP2231, I OFFSET around 5fA Have been a question about I BIAS on many interviews

8 Review from Last Lecture Bias and Offset Currents Can use superposition Will consider only the contributions by I B1 and I B2 I R OUT B1 2 For 741, if R2=10K, OUT 50nA*10K=.5m if R2=1M, OUT 50nA*1M=50m For LMP2231, if R2=10K, OUT 20fA*10K=.0.2n if R2=1M, OUT 20fA*1M=20n Effects of bias currents on most other useful circuits is very small too In those rare applications where it is of concern, using a better Op Amp is a good solution

9 Review from Last Lecture Compensation Compensation refers to adjusting the frequency dependent gain characteristics of the op amp so that the time and frequency domain performance of the feedback amplifier is acceptable Usually involves making the amplifier look like a first-order lowpass circuit If compensation is not done on cascaded-type op amps, feedback circuits using the op amp are usually unstable 0 20dB/ decade 0dB Natural type of response BW A Compensated Response Compensation often done with a capacitor which can be internal or external but usually it is internal to the Op Amp

10 Review from Last Lecture Models of Nonideal Effects GB s OS Many different models have been introduced and more exist Typically consider nonideal effects one at a time but realize all are present Application and op amp used will often determine which are of most concern

11 Review from Last Lecture Op Amp Is Almost Never Used as an Open Loop High Gain Amplifier!! L OUT It only costs 25, lets for it! But what will happen if an engineer attempts to use this circuit as an amplifier?

12 Op Amp Is Almost Never Used as an Open Loop High Gain Amplifier!! L OUT But what will happen if an engineer attempts to use this circuit as an amplifier? This is the I/O characteristics of this circuit!

13 Op Amp Is Almost Never Used as an Open Loop High Gain Amplifier!! OUT R L SATH OUT DD A 0 SS 1 DIFF DD Δ - SATP A 0 SATN SATL SS This is the I/O characteristics of this circuit!

14 Op Amp Is Almost Never Used as an Open Loop High Gain Amplifier!! OUT R L Δ - SATP A 0 SATN OUT >0 SATH <0 SATL

15 Op Amp Is Almost Never Used as an Open Loop High Gain Amplifier!! OUT R L OUT >0 SATH <0 SATL This circuit serves as a comparator! This circuit serves as a 1-bit analog to digital converter (ADC) This circuit compares to ground and provides a 2-level output

16 What will happen if the sinusoidal signal is put in? (Assume op amp biased with +/- 16 supplies and OUTSAT =15 OUT 15 for >0 = -15 for <0 Even though it is not an amplifier, is this a useful circuit?

17 What are the transfer characteristics of this simple circuit? By superposition 1 5 OUT = What if takes on one of two values, +15, or -15? = OUT 5 when =15 0 when =-15

18 Comparator with Controlled Boolean Output Levels (Assume op amp biased with +/- 16 supplies and OUTSAT =15 What are the transfer characteristics of this simple circuit? X 15 for >0 = -15 for <0 = OUT 5 0 when = 15 X when =-15 X = OUT 5 when <0 0 when >0 The circuit in yellow is termed an interface circuit

19 Applications of Comparators (Assume op amp biased with +/- 16 supplies and OUTSAT =15 This I/O relationship holds for any input! = OUT 5 when <0 0 when >0

20 The Comparators (Assume SATH = DD, SATL = SS ) OUT DD for >REF = for < SS REF OUT DD for <REF = for > SS REF Op Amps make good comparators when operated open-loop Some ICs are manufactured to serve only as comparators and often have better performance than op amps

21 Programmable Threshold Comparator (Assume op amp biased with +/- 16 supplies and OUTSAT =15 = OUT 5 0 when > when < POT POT What if the input is the output of a temperature sensor? Could serve as a thermostat! But may work too good since no hysteresis What if the input is the output of a light sensor? Could be used to turn lights on at dusk, off at dawn!

22 The Op Amp is Highly Nonlinear when Over-Driven Previous (linear) model = A OUT 0 Nonlinear model SATH DIFF> = SATL OUT A0 < DIFF< A SATL DIFF< Nonlinear model is a piecewise linear model Continuity at transitions but derivatives are not continuous SATH SATH 0 0 SATL A 0 A A 0

23 The Op Amp is Highly Nonlinear when Over-Driven The comparator circuit is also highly nonlinear Many useful applications of op amps when operating nonlinearly Many other nonlinear devices exist that are also very useful

24 Nonlinear Circuits and Applications Definition: A circuit is nonlinear if one or more devices in the circuit do not operate linearly Superposition can not be used to analyze circuit Nonlinear circuit applications Will first consider applications where op amp operates nonlinearly Will then consider other nonlinear devices Will first discuss the concepts of nonlinear circuits and nonlinear circuit analysis techniques

25 Some common types of nonlinearity

26 Observations: Nonlinear Circuits Nonlinear analysis is often more difficult than linear analysis Nonlinear analysis is sometimes less difficult than linear analysis Some very useful circuits are based upon nonlinear operation Almost all logic circuits ADCs and DACs Many nearly linear circuits are designed by using a large number of nonlinear devices MOSFET BJT Diode

27 Observations: Nonlinear Circuits Nonlinear analysis is often more difficult than linear analysis because a large number of devices and circuits that are not linear are lumped into the category of nonlinear circuits but there are many different types of nonlinearities and each may require special considerations for analysis, design, and understanding

28 Methods of Analysis of Nonlinear Circuits KCL and KL apply to both linear and nonlinear circuits Superposition, voltage divider and current divider equations, Thevenin and Norton equivalence apply only to linear circuits! Some other analysis techniques that have been developed may apply only to linear circuits as well

29 Methods of Analysis of Nonlinear Circuits Will consider three different analysis requirements and techniques for some particularly common classes of nonlinear circuits 1. Circuits with continuously differential devices Interested in obtaining transfer characteristics of these circuits or outputs for given input signals 2. Circuits with piecewise continuous devices interested in obtaining transfer characteristics of these circuits or outputs for a given input signals 3. Circuits with small-signal inputs that vary around some operating point Interested in obtaining relationship between small-signal inputs and the corresponding small-signal outputs. Will assume these circuits operate linearly in some suitably small region around the operating point Other types of nonlinearities may exist and other types of analysis may be required but we will not attempt to categorize these scenarios in this course

30 1. Nonlinear circuits with continuously differential devices Analysis Strategy: Use KL and KCL for analysis Represent nonlinear models for devices either mathematically or graphically Solve the resultant set of equations for the variables of interest

31 2. Circuits with piecewise continuous devices e.g. f ( x) Analysis Strategy: ( ) ( ) f x x < x 1 1 = f x x > x 2 1 Guess region of operation region 1 region 2 Solve resultant circuit using the previous method erify region of operation is valid Repeat the previous 3 steps as often as necessary until region of operation is verified It helps to guess right the first time but a wrong guess will not result in an incorrect solution because a wrong guess can not be verified

32 3. Circuits with small-signal inputs that vary around some operating point Interested in obtaining relationship between small-signal inputs and the corresponding small-signal outputs. Will assume these circuits operate linearly in some suitably small region around the operating point Analysis Strategy: Determine the operating point (using method 1 or 2 discussed above after all small signal independent inputs are set to 0) Develop small signal (linear) model for all devices in the region of interest (around the operating point or Q-point ) Create small signal equivalent circuit by replacing all devices with small-signal equivalent Solve the resultant small-signal (linear) circuit Can use KCL, KL, and other linear analysis tools such as superposition, voltage and current divider equations, Thevenin and Norton equivalence Determine boundary of region where small signal analysis is valid

33 End of Lecture 20