DEPARTMENT OF MECHANICAL ENGINEERING. ME 6502 Heat and Mass Transfer III YEAR-V SEMESTER

Size: px
Start display at page:

Download "DEPARTMENT OF MECHANICAL ENGINEERING. ME 6502 Heat and Mass Transfer III YEAR-V SEMESTER"

Transcription

1 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER ME 650 Heat and Mass Transfer III YEAR-V SEMESTER NAME :. REG.NO :. BRANCH :... YEAR & SEM :. 1

2 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 1. State Fourier s Law of conduction. UNIT-1 CONDUCTION Part-A The rate of heat conduction is proportional to the area measured normal to the direction of heat flow and to the temperature gradient in that direction. Q - A dt dx dt Q - KA where A are in m dx dt dx - Temperature gradient in K/m K Thermal conductivity W/mK.. Define Thermal Conductivity. Thermal conductivity is defined as the ability of a substance to conduct heat.. Write down the equation for conduction of heat through a slab or plane wall. Heat transfer Q T overall Where T = T 1 T R L R - Thermal resistance of slab KA L = Thickness of slab, K = Thermal conductivity of slab, A = Area 4. Write down the equation for conduction of heat through a hollow cylinder. Heat transfer Q T overall Where, T = T 1 T R R 1 r in LK r1 thermal resistance of slab L Length of cylinder, K Thermal conductivity, r Outer radius, r 1 inner radius 5. State Newton s law of cooling or convection law. Heat transfer by convection is given by Newton s law of cooling

3 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Q = ha (T s - T ) Where A Area exposed to heat transfer in m, h - heat transfer coefficient in W/m K T s Temperature of the surface in K, T - Temperature of the fluid in K. 6. Write down the general equation for one dimensional steady state heat transfer in slab or plane wall with and without heat generation. T T T 1 T x y z t T T T q 1 T x y z K t 7. Define overall heat transfer co-efficient. The overall heat transfer by combined modes is usually expressed in terms of an overall conductance or overall heat transfer co-efficient U. Heat transfer Q = UA T. 8. Write down the equation for heat transfer through composite pipes or cylinder. Heat transfer T Q R overall, Where, T = T a T b, r r 1 In In L r1 r L har1 K1 K hbr R. 9. What is critical radius of insulation (or) critical thickness? Critical radius = r c Critical thickness = r c r 1 Addition of insulating material on a surface does not reduce the amount of heat transfer rate always. In fact under certain circumstances it actually increases the heat loss up to certain thickness of insulation. The radius of insulation for which the heat transfer is maximum is called critical radius of insulation, and the corresponding thickness is called critical thickness. 10. Define fins (or) extended surfaces. It is possible to increase the heat transfer rate by increasing the surface of heat transfer. The surfaces used for increasing heat transfer are called extended surfaces or sometimes known as fins.

4 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 11. State the applications of fins. The main applications of fins are 1. Cooling of electronic components. Cooling of motor cycle engines.. Cooling of transformers 4. Cooling of small capacity compressors 1. Define Fin efficiency. The efficiency of a fin is defined as the ratio of actual heat transfer by the fin to the maximum possible heat transferred by the fin. fin Q Q fin max 1. Define Fin effectiveness. Fin effectiveness is the ratio of heat transfer with fin to that without fin Fin effectiveness = Q Q with fin without fin Part -B 1. A wall is constructed of several layers. The first layer consists of masonry brick 0 cm. thick of thermal conductivity 0.66 W/mK, the second layer consists of cm thick mortar of thermal conductivity 0.6 W/mK, the third layer consists of 8 cm thick lime stone of thermal conductivity 0.58 W/mK and the outer layer consists of 1. cm thick plaster of thermal conductivity 0.6 W/mK. The heat transfer coefficient on the interior and exterior of the wall are 5.6 W/m K and 11 W/m K respectively. Interior room temperature is C and outside air temperature is -5C. Calculate a) Overall heat transfer coefficient b) Overall thermal resistance c) The rate of heat transfer d) The temperature at the junction between the mortar and the limestone. Given Data 4

5 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Thickness of masonry L 1 = 0cm = 0.0 m Thermal conductivity K 1 = 0.66 W/mK Thickness of mortar L = cm = 0.0 m Thermal conductivity of mortar K = 0.6 W/mK Thickness of limestone L = 8 cm = 0.08 m Thermal conductivity K = 0.58 W/mK Thickness of Plaster L 4 = 1. cm = 0.01 m Thermal conductivity K 4 = 0.6 W/mK Interior heat transfer coefficient h a = 5.6 W/m K Exterior heat transfer co-efficient h b = 11 W/m K Interior room temperature T a = C + 7 = 95 K Outside air temperature T b = -5C + 7 = 68 K. Solution: Heat flow through composite wall is given by T Q overall [From equation (1)] (or) [HMT Data book page No. 4] R Where, T = T a T b 5

6 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 1 L L L L R h a A K 1 A K A K A K 4 A h b A Ta Tb Q 1 L1 L L L4 1 h A K A K A K A K A h A a Q/ A Heat transfer per unit area Q/A = 4.56 W/m b We know, Heat transfer Q = UA (T a T b ) [From equation (14)] Where U overall heat transfer co-efficient Q U A ( T T ) 4.56 U a b Overall heat transfer co - efficient U = 1.8 W/m We know Overall Thermal resistance (R) K 1 L L L L R h a A K 1 A K A K A K 4 A h b A For unit Area 1 L L L L R h a K 1 K K K 4 h b = R 0.78 K / W Interface temperature between mortar and the limestone T Interface temperatures relation 6

7 1 1 1 SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER T T T T T T T T T T T T R R R R R R a Q Ta T1 Q R T 1 1 Q = R a 1/ haa haa 95 T1 Q/ A 1/ h 95 T / 5.6 T 88.8 K a a T T Q R a b b 88.8 T Q L KA R L ka 88.8 T Q/ A L1 K 88.8 T T 78. K Q = T T R 78. T Q L KA 78. T Q/ A L K 78. T T 76.5 K 1 R L KA Temperature between Mortar and limestone (T is 76.5 K) 7

8 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER. A furnace wall made up of 7.5 cm of fire plate and 0.65 cm of mild steel plate. Inside surface exposed to hot gas at 650C and outside air temperature 7C. The convective heat transfer coefficient for inner side is 60 W/m K. The convective heat transfer co-efficient for outer side is 8W/m K. Calculate the heat lost per square meter area of the furnace wall and also find outside surface temperature. Given Data Thickness of fire plate L 1 = 7.5 cm = m Thickness of mild steel L = 0.65 cm = m Inside hot gas temperature T a = 650C + 7 = 9 K Outside air temperature T b = 7C + 7 = 00K Convective heat transfer co-efficient for Inner side h a = 60W/m K Convective heat transfer co-efficient for Outer side h b = 8 W/m K. Solution: (i) Heat lost per square meter area (Q/A) Thermal conductivity for fire plate K 1 = W/mK [From HMT data book page No.11] Thermal conductivity for mild steel plate K = 5.6W/mK [From HMT data book page No.1] 8

9 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Heat flow Q T overall, Where R T = T a T b 1 L L L 1 1 R h a A K 1 A K A K A h b A Ta Tb Q= 1 L1 L L 1 h A K A K A K A h A a 1 b [The term L is not given so neglect that term] Ta Tb Q= 1 L1 L L 1 h A K A K A K A h A a The term L 1 Ta Tb Q = 1 L1 L 1 h A K A K A h A Q/ A Q / A W / m is not given so neglect that term] a b b 9

10 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER (ii) Outside surface temperature T We know that, Interface temperatures relation Ta Tb Ta T1 T1 T T T T Tb Q...( A) R R R R R T T ( A) Q R where R b 1 ha b b T T Q 1 ha b b b a 1 b Q/A = T T 1 h T b b T K. A steel tube (K = 4.6 W/mK) of 5.08 cm inner diameter and 7.6 cm outer diameter is covered with.5 cm layer of insulation (K = 0.08 W/mK) the inside surface of the tube receivers heat from a hot gas at the temperature of 16C with heat transfer co-efficient of 8 W/m K. While the outer surface exposed to the ambient air at 0C with heat transfer coefficient of 17 W/m K. Calculate heat loss for m length of the tube. Given Steel tube thermal conductivity K 1 = 4.6 W/mK Inner diameter of steel d 1 = 5.08 cm = m Inner radius r 1 = m Outer diameter of steel d = 7.6 cm = m Outer radius r = m Radius r = r + thickness of insulation Radius r = m r = m Thermal conductivity of insulation K = 0.08 W/mK Hot gas temperature T a = 16C + 7 = 589 K 10

11 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Ambient air temperature T b = 0C + 7 = 0 K Heat transfer co-efficient at inner side h a = 8 W/m K Heat transfer co-efficient at outer side h b = 17 W/m K Length L = m Solution : Toverall Heat flow Q [From equation No.(19) or HMT data book Page No.5] R Where T = T a T b r 1 r 1 r 4 1 R In In In L ha r1 K1 r1 K r K r hb r4 Ta Tb Q = r 1 r 1 r 4 1 In In In L har1 K1 r1 K r K r hb r4 [The terms K and r 4 are not given, so neglect that terms] Q = T a T r 1 r 1 In In L har1 K1 r1 K r hb r b Q = In + In Q W Heat loss Q = W. 4. Derive an expression of Critical Radius of Insulation For A Cylinder. Consider a cylinder having thermal conductivity K. Let r 1 and r 0 inner and outer radii of insulation. 11

12 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Heat transfer Ti T Q r 0 In r1 KL [From equation No.()] Considering h be the outside heat transfer co-efficient. Q = Here A T T r 0 In r 1 1 KL A h r L 0 0 Ti T Q r 0 In r 1 1 KL r Lh i 0 0 zero. To find the critical radius of insulation, differentiate Q with respect to r 0 and equate it to 0 (T T ) 1 1 dq KLr hlr dr0 1 r 0 1 In KL r 1 hlr0 since (T T ) 0 i KLr hlr K r r h 0 c i A wire of 6 mm diameter with mm thick insulation (K = 0.11 W/mK). If the convective heat transfer co-efficient between the insulating surface and air is 5 W/m L, find the critical thickness of insulation. And also find the percentage of change in the heat transfer rate if the critical radius is used. 1

13 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Given Data Solution : d 1 = 6 mm r 1 = mm = 0.00 m r = r 1 + = + = 5 mm = m K = 0.11 W/mK h b = 5 W/m K K 1. Critical radius r c [From equation No.(1)] h 0.11 rc m 5 r c m Critical thickness = r c r Critical thickness t c = m - 10 (or) 1.4 mm. Heat transfer through an insulated wire is given by Ta Tb Q1 r In 1 r 1 1 L K1 hbr 1

14 ME650 HEAT AND MASS TRNSFER = Q1 = MARKS & 16 MARKS QUESTION AND ANSWER From HMT data book Page No.5 L (T T ) In L (Ta T b) 1.64 a b Heat flow through an insulated wire when critical radius is used is given by T T Q r r r c In 1 r 1 1 L K1 hbr c a b c = Q = L (T T ) In L (Ta T b) 1.57 a b Percentage of increase in heat flow by using Q Q1 Critical radius = 100 Q % 1 14

15 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 6. An aluminium alloy fin of 7 mm thick and 50 mm long protrudes from a wall, which is maintained at 10C. The ambient air temperature is C. The heat transfer coefficient and conductivity of the fin material are 140 W/m K and 55 W/mK respectively. Determine 1. Temperature at the end of the fin.. Temperature at the middle of the fin.. Total heat dissipated by the fin. Given Thickness t = 7mm = m Length L= 50 mm = m Base temperature T b = 10C + 7 = 9 K Ambient temperature T = + 7 = 95 K Heat transfer co-efficient h = 140 W/m K Thermal conductivity K = 55 W/mK. Solution : Length of the fin is 50 mm. So, this is short fin type problem. Assume end is insulated. We know Temperature distribution [Short fin, end insulated] T T cos h m [L -x]...(a) T T cos h (ml) b [From HMT data book Page No.41] (i) Temperature at the end of the fin, Put x = L 15

16 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER (A) T - T cos h m [L-L] Tb T cos h (ml) T - T 1 Tb T cos h (ml)...(1) where m = hp KA P = Perimeter = L (Approx) = P = 0.1 m A Area = Length thickness = A.5 10 m hp m = KA m (1) T - T 1 T T cos h ( ) b T - T 1 T T.05 b T T - 95 = 47.8 T = 4.8 K Temperature at the end of the fin T xl (ii) Temperature of the middle of the fin, Put x = L/ in Equation (A) 4.8 K 16

17 (A) b b SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER T - T cos hm [L-L/] T T cos h (ml) cos h T - T T T cos h 6.9 (0.050) T T T K Temperature at the middle of the fin T xl / K (iii) Total heat dissipated [From HMT data book Page No.41] 1/ Q = (hpka) (Tb T )tan h (ml) -4 1/ [ ] (9 95) tan h ( ) Q = 44.4 W 7. A copper plate mm thick is heated up to 400C and quenched into water at 0C. Find the time required for the plate to reach the temperature of 50C. Heat transfer co-efficient is 100 W/m K. Density of copper is 8800 kg/m. Specific heat of copper = 0.6 kj/kg K. Plate dimensions = 0 0 cm. Given Thickness of plate L = mm = 0.00 m Initial temperature T 0 = 400C + 7 = 67 K Final temperature T = 0C + 7 = 0 K Intermediate temperature T = 50C + 7 = K Heat transfer co-efficient h = 100 W/m K Density = 8800 kg/m Specific heat C = 60 J/kg k 17

18 Plate dimensions = 0 0 cm SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER To find Time required for the plate to reach 50C. [From HMT data book Page No.] Solution: Thermal conductivity of the copper K = 86 W/mK For slab, L Characteristic length Lc 0.00 = L c m We know, hlc Biot number Bi K B i = Biot number value is less than 0.1. So this is lumped heat analysis type problem. For lumped parameter system, T T T T 0 We know, ha t C V e.(1) [From HMT data book Page No.48] Characteristics length L c = V A 18

19 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER T-T (1) e T T - 0 e 67-0 t = 9.4 s 0 h t C Lc 100 t Time required for the plate to reach 50C is 9.4 s. 8. A steel ball (specific heat = 0.46 kj/kgk. and thermal conductivity = 5 W/mK) having 5 cm diameter and initially at a uniform temperature of 450C is suddenly placed in a control environment in which the temperature is maintained at 100C. Calculate the time required for the balls to attained a temperature of 150C. Take h = 10W/m K. Given Specific heat C = 0.46 kj/kg K = 460 J/kg K Thermal conductivity K = 5 W/mK Diameter of the sphere D = 5 cm = 0.05 m Radius of the sphere R = 0.05 m Initial temperature T 0 = 450C + 7 = 7 K Final temperature T = 100C + 7 = 7 K Intermediate temperature T = 150C + 7 = 4 K Heat transfer co-efficient h = 10 W/m K To find Time required for the ball to reach 150C [From HMT data book Page No.1] Solution Density of steel is 78 kg/m 78 kg/m For sphere, R Characteristic Length Lc 19

20 We know, hlc Biot number Bi K SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 0.05 = Lc m B i = < 0.1 Biot number value is less than 0.1. So this is lumped heat analysis type problem. For lumped parameter system, T T T T 0 ha t C V e.(1) We know, [From HMT data book Page No.48] Characteristics length L c = V A T-T (1) e T T 0 h t C Lc 10 t e In 10 t t = s Time required for the ball to reach 150C is s. 0

21 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 9. Alloy steel ball of mm diameter heated to 800C is quenched in a bath at 100C. The material properties of the ball are K = 05 kj/m hr K, = 7860 kg/m, C = 0.45 kj/kg K, h = 150 KJ/ hr m K. Determine (i) Temperature of ball after 10 second and (ii) Time for ball to cool to 400C. Given Diameter of the ball D = 1 mm = 0.01 m Radius of the ball R = 0.006m Initial temperature T 0 = 800C + 7 = 107 K Final temperature T = 100C + 7 = 7 K Thermal conductivity K = 05 kj/m hr K J 600 s mk W /mk [ J/s = W] Density = 7860 kg/m Specific heat C = 0.45 kj/kg K = 450 J/kg K Heat transfer co-efficient h = 150 kj/hr m K J 600 s m K W /m K Solution Case (i) Temperature of ball after 10 sec. For sphere, R Characteristic Length Lc = We know, hlc Biot number Bi K L c 0.00 m 1

22 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER B i = < 0.1 Biot number value is less than 0.1. So this is lumped heat analysis type problem. For lumped parameter system, T T T T 0 We know, ha t C V e.(1) [From HMT data book Page No.48] Characteristics length L c = V A 0 h t C Lc T-T (1) e...() T T T - 7 e T = K Case (ii) Time for ball to cool to 400C T = 400C + 7 = 67 K 0 h t C Lc T-T () e...() T T t e In t t = s 10. A large steel plate 5 cm thick is initially at a uniform temperature of 400C. It is suddenly exposed on both sides to a surrounding at 60C with convective heat transfer co-efficient of 85

23 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER W/m K. Calculate the centre line temperature and the temperature inside the plate 1.5 cm from themed plane after minutes. Take K for steel = 4.5 W/mK, for steel = 0.04 m /hr. Given Thickness L = 5 cm = 0.05 m Initial temperature T i = 400C + 7 = 67 K Final temperature T = 60C + 7 = K Distance x = 1.5 mm = m Time t = minutes = 180 s Heat transfer co-efficient h = 85 W/m K Thermal diffusivity = 0.04 m /hr = m /s. Thermal conductivity K = 4.5 W/mK. Solution For Plate : L Characteristic Length Lc 0.05 = We know, hlc Biot number Bi K Bi Infinite Solids Case (i) L c 0.05 m 0.1 < B i < 100, So this is infinite solid type problem. [To calculate centre line temperature (or) Mid plane temperature for infinite plate, refer HMT data book Page No.59 Heisler chart].

24 X axis SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER c = c X axis Fourier number =.4 hl Curve K hl K c Curve t Fourier number = L (0.05) X axis value is.4, curve value is 0.167, corresponding Y axis value is 0.64 T T T T 0 Y axis = 0.64 T0 T T T i 0.64 i 0 T T T T i 0.64 T T K Center line temperature T K Case (ii) Temperature (T x ) at a distance of m from mid plane [Refer HMT data book Page No.60, Heisler chart] 4

25 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER hl K x Curve 0.5 L 0.05 c X axis Biot number Bi c X axis value is 0.167, curve value is 0.5, corresponding Y axis value is T T x 0 T T 0.97 x Y axis = 0.97 T T x 0 x T T T T 0 T T 0.97 Tx T 544 K Temperature inside the plate 1.5 cm from the mid plane is 544 K. 5

26 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 1. Define convection. UNIT- CONVECTION Part-A Convection is a process of heat transfer that will occur between a solid surface and a fluid medium when they are at different temperatures.. Define Reynolds number (Re) & Prandtl number (Pr). Reynolds number is defined as the ratio of inertia force to viscous force. Re Inertia force Viscous force Prandtl number is the ratio of the momentum diffusivity of the thermal diffusivity. Momentum diffusivity Pr Thermal diffusivity. Define Nusselt number (Nu). It is defined as the ratio of the heat flow by convection process under an unit temperature gradient to the heat flow rate by conduction under an unit temperature gradient through a stationary thickness (L) of metre. Nusselt number (Nu) = Q conv. Q cond 4. Define Grash of number (Gr) & Stanton number (St). It is defined as the ratio of product of inertia force and buoyancy force to the square of viscous force. Inertia force Buyoyancy force Gr (Viscous force) Stanton number is the ratio of nusselt number to the product of Reynolds number and prandtl number. 6

27 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Nu St Re Pr 5. What is meant by Newtonian and non Newtonian fluids? The fluids which obey the Newton s Law of viscosity are called Newtonian fluids and those which do not obey are called non Newtonian fluids. 6. What is meant by laminar flow and turbulent flow? Laminar flow: Laminar flow is sometimes called stream line flow. In this type of flow, the fluid moves in layers and each fluid particle follows a smooth continuous path. The fluid particles in each layer remain in an orderly sequence without mixing with each other. Turbulent flow: In addition to the laminar type of flow, a distinct irregular flow is frequency observed in nature. This type of flow is called turbulent flow. The path of any individual particle is zig zag and irregular. Fig. shows the instantaneous velocity in laminar and turbulent flow. 7. What is meant by free or natural convection & forced convection? If the fluid motion is produced due to change in density resulting from temperature gradients, the mode of heat transfer is said to be free or natural convection. If the fluid motion is artificially created by means of an external force like a blower or fan, that type of heat transfer is known as forced convection. 8. Define boundary layer thickness. The thickness of the boundary layer has been defined as the distance from the surface at which the local velocity or temperature reaches 99% of the external velocity or temperature. 9. What is the form of equation used to calculate heat transfer for flow through cylindrical pipes? Nu = 0.0 (Re) 0.8 (Pr) n n = 0.4 for heating of fluids n = 0. for cooling of fluids 7

28 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 10. What is meant by Newtonian and non Newtonian fluids? The fluids which obey the Newton s Law of viscosity are called Newtonian fluids and those which do not obey are called non Newtonian fluids. Part-B 1. Air at 0C, at a pressure of 1 bar is flowing over a flat plate at a velocity of m/s. if the plate maintained at 60C, calculate the heat transfer per unit width of the plate. Assuming the length of the plate along the flow of air is m. Given : Fluid temperature T = 0C, Pressure p = 1 bar, Velocity U = m/s, Plate surface temperature T w = 60C, Width W = 1 m, Length L = m. Solution : We know, Film temperature 60 0 T 40C f T f T w T Properties of air at 40C: Density = 1.19 Kg/m Thermal conductivity K = W /mk, 6 Kinematic viscosity v = m / s. Prandtl number Pr = We know, Reynolds number Re = UL v

29 4 5 Re SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Reynolds number value is less than , so this is laminar flow. For flat plate, Laminar flow, Local Nusselt Number Nu x = 0. (Re) 0.5 (Pr) 0. Nu 0. ( ) (0.699) x Nu x We know that, Local Nusselt Number Nu h s x hs L K Local heat transfer coefficient h x =.7 W/m K We know, Average heat transfer coefficient h = h x h.7 h = 4.65 W/m K Heat transfer Q = h A (T w - T ) 4.65 (60 0) [ Area widthlength 1 ] Q 7 Watts.. Air at 0C at atmospheric pressure flows over a flat plate at a velocity of m/s. if the plate is 1 m wide and 80C, calculate the following at x = 00 mm. 1. Hydrodynamic boundary layer thickness,. Thermal boundary layer thickness,. Local friction coefficient, 4. Average friction coefficient, 9

30 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 5. Local heat transfer coefficient 6. Average heat transfer coefficient, 7. Heat transfer. Given: Fluid temperature T = 0C Velocity U = m/s Wide W = 1 m Surface temperature Tw = 80C Distance x = 00 mm = 0. m Solution: We know, Film temperature Tw T Tf 80 0 T 50C f Properties of air at 50C Density = 1.09 kg/m Kinematic viscosity v = Pr andt l number Pr =0.698 Thermal conductivity K = 8.6 We know, Reynolds number Re = UL v Re Since Re < , flow is laminar For Flat plate, laminar flow, m / s - 10 W / mk 1. Hydrodynamic boundary layer thickness: 0

31 hx hx 5 x (Re) m SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 0.5 = 5 0. ( ) Thermal boundary layer thickness: TX (Pr) hx TX TX (0.698) m 0.. Local Friction coefficient: C fx fx 0.664(Re) = ( ) C = Average friction coefficient: C fl fl 1.8 (Re) = 1.8 ( ) = C Local heat transfer coefficient (h x ): Local Nusselt Number Nu x = 0. (Re) 0.5 (Pr) ( ) (0.698) Nu 65.9 x We know Local Nusselt Number

32 hx L Nux K h h SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER x 65.9 x = L = 0.m x 6.0 W/m K Local heat transfer coefficient h 6. Average heat transfer coefficient (h): h h h x Heat transfer: 1.41 W /m K x 6.0 W / mk We know that, Q h A(T T ) w = 1.41 (10.) (80-0) Q =.8 Watts. Air at 0C flows over a flat plate at a velocity of m/s. The plate is m long and 1.5 m wide. Calculate the following: To find: 1. Boundary layer thickness. Total drag force.. Total mass flow rate through the boundary layer between x = 40 cm and x = 85 cm. Given: Fluid temperature T = 0C Velocity Length Wide W U = m/s L = m W = 1.5 m

33 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Solution: Properties of air at 0C kg/m 6 v m / s Pr K W /mk We know, UL Reynolds numberre v Re Since Re< ,flow is laminar For flat plate, laminar flow, [from HMT data book, Page No.99] Hydrodynamic boundary layer thickness hx hx 5 x (Re) 0.5 = 5 (.510 ) 0.0 m Thermal boundary layer thickness,

34 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 0. tx hx (Pr) TX =0.0 (0.701) 0.05 m -0. We know, Average friction coefficient, C fl fl 1.8 (Re) 0.5 = 1.8 (.5 10 ) C We know C t U t () Average shear stress t = N/ m fl Drag force = Area Average shear stress = Drag force = N Drag force on two sides of the plate = = 0.06 N Total mass flow rate between x = 40 cm and x= 85 cm. 4

35 SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 5 m U hx hx 8 Hydrodynamic boundary layer thickness hx0.5 5 x (Re) 0.5 U x = v HX0.85 hx= HX m = 5 x (Re) U x v m 5 (1) m= m = Kg/ s, 4. Air at 90C flows over a flat plate at a velocity of 6 m/s. The plate is 1m long and 0.5 m wide. The pressure of the air is 6 kn/m. If the plate is maintained at a temperature of 70C, estimate the rate of heat removed from the plate. Given : Fluid temperature T = 90C Velocity U = 6 m/s. Length L = 1 m Wide W = 0.5 m Pressure of air P = 6 kn/m 6 10 N/m Plate surface temperature T w = 70C 5

36 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER To find: Heat removed from the plate Tw T Solution: We know, Film temperature Tf T 180C f Properties of air at 180C (At atmospheric pressure) Kg/m -6 = m / s Pr K W/mK Note: Pressure other than atmospheric pressure is given, so kinematic viscosity will vary with pressure. Pr, K, C p are same for all pressures. P Kinematic viscosity atm P atm given N/ m bar Atmospheric pressure = 1 bar 5 10 N/ m 6 10 N/ m 5 1 bar = 110 N/m -4 Kinematic viscosity v = m / s. We know, Reynolds number UL Re v 6

37 Re SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Since Re< 5 10, flow is laminar For plate, laminar flow, Local nusselt number NU 0. (Re) (Pr) x x ( ) (0.681) NU hl x We know NU x = K h x 0.6 [ L = 1 m] Local heat transfer coefficient h x 1.15 W/m K We know Average heat transfer coefficient h = h x h 1.15 h.1 W/m K We know Heat transferred Q h A (T T ).1 (1 0.5) (56 4) Q 54.1 W Heat transfer from both side of the plate = 54.1 w = 508. W. 7

38 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 5. Air at 40C flows over a flat plate, 0.8 m long at a velocity of 50 m/s. The plate surface is maintained at 00C. Determine the heat transferred from the entire plate length to air taking into consideration both laminar and turbulent portion of the boundary layer. Also calculate the percentage error if the boundary layer is assumed to be turbulent nature from the very leading edge of the plate. Given : Fluid temperature T = 40C, Length L = 0.8 m, Velocity U = 50 m/s, Plate surface temperature T w = 00C To find : 1. Heat transferred for: i. Entire plate is considered as combination of both laminar and turbulent flow. ii. Entire plate is considered as turbulent flow.. Percentage error. Solution: We know Film temperature T f T w T T K T 170C f Pr operties of air at 170C: = Kg/m m / s Pr K 7 10 W/mK We know UL Reynolds number Re= v Re = Re ,so this is turbulent flow 6 8

39 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Case (i): Laminar turbulent combined. [It means, flow is laminar upto Reynolds number value is , after that flow is turbulent] Average nusselt number = Nu = (Pr) 0. (Re) Nu = (0.6815) 0. [0.07 ( ) Average nusselt number Nu = hl We know Nu = K h h 78.8 W / m K Average heat transfer coefficient h=78.8 W/m K Head transfer Q h A (T T ) 1 1 w hl W (T T ) = (00-40) Q W w Case (ii) : Entire plate is turbulent flow: Local nusselt number} Nux = (Re) 0.8 (Pr) 0. NU x = ( ) 0.8 (0.6815) 0. NU x = We know NU x hx L K h 0.8 x hx W/m K 9

40 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Local heat transfer coefficient h x = W/m K Average heat transfer coefficient (for turbulent flow) h = 1.4 h x = Average heat transfer coefficient} h = W/m K We know Heat transfer Q = h A (T w + T ) = h L W (T w + T ) = (00 40) Q = 589. W Q Q1. Percentage error = Q = = 4.9% Kg/hr of air are cooled from 100C to 0C by flowing through a.5 cm inner diameter pipe coil bent in to a helix of 0.6 m diameter. Calculate the value of air side heat transfer coefficient if the properties of air at 65C are K = W/mK = 0.00 Kg/hr m Pr = 0.7 = Kg/m 40

41 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Given : Mass flow rate in = 05 kg/hr 05 Kg/ s in = Kg/s 600 Inlet temperature of air T mi = 100C Outlet temperature of air T mo = 0C Diameter D =.5 cm = 0.05 m Tmi Tmo Mean temperature Tm 65 C To find: Heat transfer coefficient (h) Solution: Reynolds Number Re = UD Kinematic viscosity 0.00 Kg/ s m Kg/m 7 v m / s Mass flow rate in = A U 41

42 D U SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER (0.05) U U = 55.7 m/s UD (1) Re = = Re = Since Re > 00, flow is turbulent For turbulent flow, general equation is (Re > 10000) Nu 0.0 (Re) (Pr) This is cooling process, so n = 0. Nu = 0.0 ( ) (0.7) Nu We know that, hd Nu K h Heat transfer coefficient h = 66. W/m K 4

43 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 7. In a long annulus (.15 cm ID and 5 cm OD) the air is heated by maintaining the temperature of the outer surface of inner tube at 50C. The air enters at 16C and leaves at C. Its flow rate is 0 m/s. Estimate the heat transfer coefficient between air and the inner tube. Given : Inner diameter D i =.15 cm = m Outer diameter D o = 5 cm = 0.05 m Tube wall temperature T w = 50C Inner temperature of air T mi = 16C Outer temperature of air t mo = C Flow rate U = 0 m/s To find: Heat transfer coefficient (h) Solution: Tmi T Mean temperature T m = 16 T 4C m Properties of air at 4C: = Kg/m -6 = m / s Pr = K = W / mk We know, 4 mo

44 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Hydraulic or equivalent diameter D P Do Di D D D D h D 4 D D 4A i 4 o o i o i D (D D ) = D h = m i o i Reynolds number Re = UD h Re = Since Re > 00, flow is turbulent For turbulent flow, general equation is (Re > 10000) Nu = 0.0 (Re) 0.8 (Pr) n This is heating process. So n = 0.4 Nu = 0.0 (5. 10 ) (0.707) Nu

45 hdh We know Nu = K h = h = 1. W/m K SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER - 8. Engine oil flows through a 50 mm diameter tube at an average temperature of 147C. The flow velocity is 80 cm/s. Calculate the average heat transfer coefficient if the tube wall is maintained at a temperature of 00C and it is m long. Given : Diameter D = 50 mm = m Average temperature T m = 147C Velocity U = 80 cm/s = 0.80 m/s Tube wall temperature T w = 00C Length L = m To find: Average heat transfer coefficient (h) Solution : Properties of engine oil at 147C = 816 Kg/m -6 = 7 10 m / s Pr = 116 K = 1.8 We know - 10 W/mK 45

46 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Reynolds number Re = Re = UD Since Re < 00 flow is turbulent L 40 D L D For turbulent flow, (Re < 10000) Nusselt number Nu = 0.06 (Re) (Pr) D L Nu 0.06 (5714.) (116) Nu 14.8 hd We know Nu = K h = h = 8. W/m K - 9. A large vertical plate 4 m height is maintained at 606C and exposed to atmospheric air at 106C. Calculate the heat transfer is the plate is 10 m wide. Given : Vertical plate length (or) Height L = 4 m Wall temperature T w = 606C 46

47 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Air temperature T = 106C Wide W = 10 m To find: Heat transfer (Q) Solution: T Film temperature T T 56C f m / s - 10 W/mK f w T Properties of air at 56C = 50C = Kg/m Pr = K = Coefficient of thermal expansion} = T in K = K Grashof number Gr = Gr = g L T (4) ( ) v ( ) 6 f Gr =

48 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Gr Pr = Gr Pr = Since Gr Pr > 10 9, flow is turbulent For turbulent flow, Nusselt number Nu = 0.10 [Gr Pr] 0. Nu = 0.10 [ ] Nu = We know that, Nusselt number hl Nu K 47.0 = h Heat transfer coefficient h = 5.78 W/m K Heat transfer Q = h A T h W L (T T ) ( ) Q W w Q = W 48

49 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 10. A thin 100 cm long and 10 cm wide horizontal plate is maintained at a uniform temperature of 150C in a large tank full of water at 75C. Estimate the rate of heat to be supplied to the plate to maintain constant plate temperature as heat is dissipated from either side of plate. Given : Length of horizontal plate L = 100 cm = 1m Wide W = 10 cm = 0.10 m Plate temperature T w = 150C Fluid temperature T = 75C To find: Heat loss (Q) from either side of plate Solution: T Film temperature T T 11.5C f -6 = m / s K = W/mK f w T Properties of water at 11.5C = 951 Kg/m Pr =

50 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 1 1 Coefficient of thermal expansion} = T in K f K Grashof Number Gr = For horizontal plate, Characteristic length L L c = 0.05 m (1) Gr = Gr = Gr Pr = g L T c v W (0.05) (150 75) 9 ( ) 6 Gr Pr = Gr Pr value is in between and i.e., < Gr Pr < For horizontal plate, upper surface heated: Nusselt number Nu = 0.15 (Gr Pr) 0. Nu = 0.15 [ ] Nu = We know that, Nusselt number Nu = h 0.05 u h u = 54.6 W/m K hl u K c 50

51 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Upper surface heated, heat transfer coefficient h u = 54.6 W/m K For horizontal plate, lower surface heated: Nusselt number Nu = 0.7 [Gr Pr] 0.5 Nu = 0.7 [ ] Nu = 7.8 We know that, hl Nusselt number Nu = K hl 1 c 7.8 K h h W/m K 1 c Lower surface heated, heat transfer coefficient h 1 = W/m K Total heat transfer Q = (h u + h 1 ) A T = (h u + h 1 ) W L (T w - T ) = ( ) 0.10 (150 75) Q = W 51

52 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER UNIT- BOILING AND CONDENSATION,HEAT EXCHANGER PART - A 1. What is meant by Boiling and condensation? The change of phase from liquid to vapour state is known as boiling. The change of phase from vapour to liquid state is known as condensation.. Give the applications of boiling and condensation. Boiling and condensation process finds wide applications as mentioned below. 1. Thermal and nuclear power plant.. Refrigerating systems. Process of heating and cooling 4. Air conditioning systems. What is meant by pool boiling? If heat is added to a liquid from a submerged solid surface, the boiling process referred to as pool boiling. In this case the liquid above the hot surface is essentially stagnant and its motion near the surface is due to free convection and mixing induced by bubble growth and detachment. 4. What is meant by Film wise and Drop wise condensation? The liquid condensate wets the solid surface, spreads out and forms a continuous film over the entire surface is known as film wise condensation. In drop wise condensation the vapour condenses into small liquid droplets of various sizes which fall down the surface in a random fashion. 5. Give the merits of drop wise condensation? In drop wise condensation, a large portion of the area of the plate is directly exposed to vapour. The heat transfer rate in drop wise condensation is 10 times higher than in film condensation. 5

53 6. What is heat exchanger? SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER A heat exchanger is defined as an equipment which transfers the heat from a hot fluid to a cold fluid. 7. What are the types of heat exchangers? The types of heat exchangers are as follows 1. Direct contact heat exchangers. Indirect contact heat exchangers. Surface heat exchangers 4. Parallel flow heat exchangers 5. Counter flow heat exchangers 6. Cross flow heat exchangers 7. Shell and tube heat exchangers 8. Compact heat exchangers. 8. What is meant by Direct heat exchanger (or) open heat exchanger? In direct contact heat exchanger, the heat exchange takes place by direct mixing of hot and cold fluids. 9. What is meant by Indirect contact heat exchanger? In this type of heat exchangers, the transfer of heat between two fluids could be carried out by transmission through a wall which separates the two fluids. 10. What is meant by Regenerators? In this type of heat exchangers, hot and cold fluids flow alternately through the same space. Examples: IC engines, gas turbines. 11. What is meant by Recuperater (or) surface heat exchangers? This is the most common type of heat exchangers in which the hot and cold fluid do not come into direct contact with each other but are separated by a tube wall or a surface. 1. What is meant by parallel flow and counter flow heat exchanger? In this type of heat exchanger, hot and cold fluids move in the same direction. In this type of heat exchanger hot and cold fluids move in parallel but opposite directions. 5

54 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 1. What is meant by shell and tube heat exchanger? In this type of heat exchanger, one of the fluids move through a bundle of tubes enclosed by a shell. The other fluid is forced through the shell and it moves over the outside surface of the tubes. 14. What is meant by compact heat exchangers? There are many special purpose heat exchangers called compact heat exchangers. They are generally employed when convective heat transfer coefficient associated with one of the fluids is much smaller than that associated with the other fluid. 15. What is meant by LMTD? We know that the temperature difference between the hot and cold fluids in the heat exchanger varies from point in addition various modes of heat transfer are involved. Therefore based on concept of appropriate mean temperature difference, also called logarithmic mean temperature difference, also called logarithmic mean temperature difference, the total heat transfer rate in the heat exchanger is expressed as Q = U A (T)m Where U Overall heat transfer coefficient W/m K A Area m (T) m Logarithmic mean temperature difference. 16. What is meant by Fouling factor? We know the surfaces of a heat exchangers do not remain clean after it has been in use for some time. The surfaces become fouled with scaling or deposits. The effect of these deposits the value of overall heat transfer coefficient. This effect is taken care of by introducing an additional thermal resistance called the fouling resistance. 17. What is meant by effectiveness? The heat exchanger effectiveness is defined as the ratio of actual heat transfer to the maximum possible heat transfer. Actual heat transfer Q Effectiveness = Maximum possible heat transfer Q 54 max

55 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Part-B 1. Water is boiled at the rate of 4 kg/h in a polished copper pan, 00 mm in diameter, at atmospheric pressure. Assuming nucleate boiling conditions calculate the temperature of the bottom surface of the pan. Given : m = 4 kg / h 4 kg 600 s m kg/ s d = 00 mm =.m Solution: We know saturation temperature of water is 100C i.e. T sat = 100C Properties of water at 100C From HMT data book Page No.1 55

56 Density l = 961 kg/m SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER -6 Kinematic viscosity v = m / s Pr andtl number P r Specific heat Cpl = 4.16 kj/kg K = 416 j/kg K Dynamic viscosity l = l v = L Ns/m 6-6 From steam table (R.S. Khumi Steam table Page No.4) At 100C Enthalpy of evaporation hfg = 56.9 kj/kg hfg j/kg Specific volume of vapour Vg = 1.67 m /kg Density of vapour 1 v vg v kg/m For nucleate boiling 56

57 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Q g ( l v) CplT Heat flux lhfg A Csf hfgp We know transferred Q = mhfg Heat transferred Q = m hfg. 1.7 r Q mhg A A Q A d = (.) 4 Q w / m A - surface tension for liquid vapour interface At 100C (From HMT data book Page No.147) N/ m For water copper Csf = Surface fluid constant = 01 C sf.01 (From HMT data book Page No.145) Q Substitute, l, h fg, l, v,, Cpl, hfg, and P r values in Equation (1) A 57

58 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER (1) T (1.74) T w T(.56).85 T.056 = 0.97 T We know that Excess temperature T = T T 116.7C w w T sat 16.7 = T 100C.. A nickel wire carrying electric current of 1.5 mm diameter and 50 cm long, is submerged in a water bath which is open to atmospheric pressure. Calculate the voltage at the burn out point, if at this point the wire carries a current of 00A. Given : D = 1.5mm = m; L = 50 cm = 0.50m; Current I = 00A Solution We know saturation temperature of water is 100C 58

59 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER i.e. T sat = 100C Properties of water at 100C (From HMT data book Page No.11) l = 961 kg/m 6 v m / s P r Cpl = 4.16 kj/kg K = 416 j/kg K l= l v l Ns/m 6 6 From steam Table at 100C R.S. Khurmi Steam table Page No.4 hfg 56.9 kj/kg hfg = 56.9 v g 1.67m / kg g 10 j/kg 1 1 v kg/m 1.67 = Surface tension for liquid vapour interface At 100C N/m (From HMT data book Page No.147) 59

60 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER For nucleate pool boiling critical heat flux (AT burn out) 0.5 Q g ( l - v) 0.18hfg v 1 A v (From HMT data book Page No.14) Substitute h fg, l, v, values in Equation (1) Q A (1) ( ).597 Q W/m A We know Heat transferred Q = V I Q V I A A V 00 dl 6 V = A = dl V 17.9 volts Water is boiling on a horizontal tube whose wall temperature is maintained ct 15C above the saturation temperature of water. Calculate the nucleate boiling heat transfer coefficient. Assume 60

61 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER the water to be at a pressure of 0 atm. And also find the change in value of heat transfer coefficient when 1. The temperature difference is increased to 0C at a pressure of 10 atm.. The pressure is raised to 0 atm at T = 15C Given : Wall temperature is maintained at 15C above the saturation temperature. Tw 115C. Tsat 100C Tw C = p = 10 atm = 10 bar case (i) T 0C; p 10 atm = 10 bar case (ii) p = 0 atm = 0 bar; T - 15C Solution: We know that for horizontal surface, heat transfer coefficient h = 5.56 (T) From HMT data book Page No.18 h = 5.56 (T w T sat ) = 5.56 ( ) 61

62 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER h w/m K Heat transfer coefficient other than atmospheric pressure h p = hp 0.4 From HMT data book Page No.144 = Heat transfer coefficient hp W / m K Case (i) P = 100 bar T = 0C From HMT data book Page No.144 Heat transfer coefficient h 5.56 ( T) = 5.56(0) h W /m K Heat transfer coefficient other than atmospheric pressure h p = hp 0.4 6

63 15010 (10) h p W /m K SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Case (ii) P = 0 bar; T = 15C Heat transfer coefficient h = 5.56 (T) = 5.56 (15) h W/m K Heat transfer coefficient other than atmospheric pressure h p = hp 0.4 = (0) 0.4 hp W/m K 4. A vertical flat plate in the form of fin is 500m in height and is exposed to steam at atmospheric pressure. If surface of the plate is maintained at 60C. calculate the following. 1. The film thickness at the trailing edge. Overall heat transfer coefficient. Heat transfer rate 4. The condensate mass flow rate. Assume laminar flow conditions and unit width of the plate. 6

64 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Given : Height ore length L = 500 mm = 5m Surface temperature T w = 60C Solution We know saturation temperature of water is 100C i.e. T sat = 100C (From R.S. Khurmi steam table Page No.4 h fg = 56.9kj/kg h fg = j/kg We know Film temperature T T f 80C f T w T sat Properties of saturated water at 80C (From HMT data book Page No.1) 64

65 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER kg/m 6 v m / s - k = W/mk = p v= Ns/ m 6 1. Film thickness x We know for vertical plate Film thickness 4K x (Tsat T w ) x ghfg Where X = L = 0.5 m x x m Average heat transfer coefficient (h) 65

66 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER For vertical surface Laminar flow k gh fg h 0.94 L Tsat Tw 0.5 The factor 0.94 may be replace by 1.1 for more accurate result as suggested by Mc Adams ( ) (974) h W/m k Heat transfer rate Q We know Q ha(t T ) sat = hl W (T T ) w sat = Q = 186 W w 4. Condensate mass flow rate m We know 66

67 Q mh Q m h fg fg m m kg/s SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 10. Steam at bar is arranged to condense over a 50 cm square vertical plate. The surface temperature is maintained at 0C. Calculate the following. a. Film thickness at a distance of 5 cm from the top of the plate. b. Local heat transfer coefficient at a distance of 5 cm from the top of the plate. c. Average heat transfer coefficient. d. Total heat transfer e. Total steam condensation rate. f. What would be the heat transfer coefficient if the plate is inclined at 0C with horizontal plane. Given : Pressure P = bar Area A = 50 cm 50 cm = = 0.5 m Surface temperature T w = 0C Distance x = 5 cm =.5 m Solution Properties of steam at bar (From R.S. Khurmi steam table Page no.7) 67

68 T satj / kg SYED AMMAL ENGINEERING COLLEGE ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 41.5C h fg 40.kj/kg = j/ kg We know Film temperature T = T f 0.76C f T w T sat Properties of saturated water at 0.76C = 0C From HMT data book Page No kg/m m / s - k 6110 W /mk p v Ns / m 6 6 a. Film thickness We know for vertical surfaces 68

69 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER 0.5 4K x (Tsat T w ) x g hfg (From HMT data book Page No.150) (41.5 0)100 x x m b. Local heat transfer coefficient h x Assuming Laminar flow h h x k x x 4 hx 4,191 W/m K c. Average heat transfer coefficient h (Assuming laminar flow) 0.5 k gh fg L Tsat Tw h 0.94 The factor 0.94 may be replaced by 1.1 for more accurate result as suggested by Mc adams 0.5 k g h fg L Tsat Tw h

70 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER Where L = 50 cm =.5 m (6110 ) (997) h 1.1 h W/m k d. Heat transfer (Q) We know Q = ha(t sat T w ) h A (T T ) sat w ( Q W e. Total steam condensation rate (m) We know Heat transfer Q mh Q m h fg fg 70

71 ME650 HEAT AND MASS TRNSFER MARKS & 16 MARKS QUESTION AND ANSWER m m kg/ s f. If the plate is inclined at with horizontal h h sin inclined inclined inclined inclined vertical vertical 1/ 4 h h (sin0) h h 1 1/ W/m k 1/ 4 Let us check the assumption of laminar film condensation We know Reynolds Number R e 6 e e 4m w where W = width of the plate = 50cm =.50m R R So our assumption laminar flow is correct. 5. A condenser is to designed to condense 600 kg/h of dry saturated steam at a pressure of 0.1 bar. A square array of 400 tubes, each of 8 mm diameter is to be used. The tube surface is maintained at 0C. Calculate the heat transfer coefficient and the length of each tube. 71

Heat and Mass Transfer Unit-1 Conduction

Heat and Mass Transfer Unit-1 Conduction 1. State Fourier s Law of conduction. Heat and Mass Transfer Unit-1 Conduction Part-A The rate of heat conduction is proportional to the area measured normal to the direction of heat flow and to the temperature

More information

If there is convective heat transfer from outer surface to fluid maintained at T W.

If there is convective heat transfer from outer surface to fluid maintained at T W. Heat Transfer 1. What are the different modes of heat transfer? Explain with examples. 2. State Fourier s Law of heat conduction? Write some of their applications. 3. State the effect of variation of temperature

More information

S.E. (Chemical) (Second Semester) EXAMINATION, 2012 HEAT TRANSFER (2008 PATTERN) Time : Three Hours Maximum Marks : 100

S.E. (Chemical) (Second Semester) EXAMINATION, 2012 HEAT TRANSFER (2008 PATTERN) Time : Three Hours Maximum Marks : 100 Total No. of Questions 12] [Total No. of Printed Pages 7 Seat No. [4162]-187 S.E. (Chemical) (Second Semester) EXAMINATION, 2012 HEAT TRANSFER (2008 PATTERN) Time : Three Hours Maximum Marks : 100 N.B.

More information

S.E. (Chemical) (Second Semester) EXAMINATION, 2011 HEAT TRANSFER (2008 PATTERN) Time : Three Hours Maximum Marks : 100

S.E. (Chemical) (Second Semester) EXAMINATION, 2011 HEAT TRANSFER (2008 PATTERN) Time : Three Hours Maximum Marks : 100 Total No. of Questions 12] [Total No. of Printed Pages 7 [4062]-186 S.E. (Chemical) (Second Semester) EXAMINATION, 2011 HEAT TRANSFER (2008 PATTERN) Time : Three Hours Maximum Marks : 100 N.B. : (i) Answers

More information

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM V (ME-51, 52, 53, 54)] QUIZ TEST-1 (Session: )

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM V (ME-51, 52, 53, 54)] QUIZ TEST-1 (Session: ) QUIZ TEST-1 Time: 1 Hour HEAT AND MASS TRANSFER Note: All questions are compulsory. Q1) The inside temperature of a furnace wall ( k=1.35w/m.k), 200mm thick, is 1400 0 C. The heat transfer coefficient

More information

Principles of Food and Bioprocess Engineering (FS 231) Problems on Heat Transfer

Principles of Food and Bioprocess Engineering (FS 231) Problems on Heat Transfer Principles of Food and Bioprocess Engineering (FS 1) Problems on Heat Transfer 1. What is the thermal conductivity of a material 8 cm thick if the temperature at one end of the product is 0 C and the temperature

More information

Tutorial 1. Where Nu=(hl/k); Reynolds number Re=(Vlρ/µ) and Prandtl number Pr=(µCp/k)

Tutorial 1. Where Nu=(hl/k); Reynolds number Re=(Vlρ/µ) and Prandtl number Pr=(µCp/k) Tutorial 1 1. Explain in detail the mechanism of forced convection. Show by dimensional analysis (Rayleigh method) that data for forced convection may be correlated by an equation of the form Nu = φ (Re,

More information

Fatima

Fatima Fatima QUESTION BANK DEPARTMENT: MECH SEMESTER: IV SUBJECT CODE / Name: ME 2251/HEAT AND MASS TRANSFER UNIT I: CONDUCTION PART -A (2 Marks) 1. What is Fourier's Law of heat conduction? (May 05, May 06,

More information

TOPIC 2 [A] STEADY STATE HEAT CONDUCTION

TOPIC 2 [A] STEADY STATE HEAT CONDUCTION TOPIC 2 [A] STEADY STATE HEAT CONDUCTION CLASS TUTORIAL 1. The walls of a refrigerated truck consist of 1.2 mm thick steel sheet (k=18 W/m-K) at the outer surface, 22 mm thick cork (k=0.04 W/m-K) on the

More information

SEM-2017(03HI MECHANICAL ENGINEERING. Paper II. Please read each of the following instructions carefully before attempting questions.

SEM-2017(03HI MECHANICAL ENGINEERING. Paper II. Please read each of the following instructions carefully before attempting questions. We RoU No. 700095 Candidate should write his/her Roll No. here. Total No. of Questions : 7 No. of Printed Pages : 7 SEM-2017(03HI MECHANICAL ENGINEERING Paper II Time ; 3 Hours ] [ Total Marks : 0 Instructions

More information

Examination Heat Transfer

Examination Heat Transfer Examination Heat Transfer code: 4B680 date: 17 january 2006 time: 14.00-17.00 hours NOTE: There are 4 questions in total. The first one consists of independent sub-questions. If necessary, guide numbers

More information

Introduction to Heat Transfer

Introduction to Heat Transfer Question Bank CH302 Heat Transfer Operations Introduction to Heat Transfer Question No. 1. The essential condition for the transfer of heat from one body to another (a) Both bodies must be in physical

More information

UNIT II CONVECTION HEAT TRANSFER

UNIT II CONVECTION HEAT TRANSFER UNIT II CONVECTION HEAT TRANSFER Convection is the mode of heat transfer between a surface and a fluid moving over it. The energy transfer in convection is predominately due to the bulk motion of the fluid

More information

Convection Heat Transfer. Introduction

Convection Heat Transfer. Introduction Convection Heat Transfer Reading Problems 12-1 12-8 12-40, 12-49, 12-68, 12-70, 12-87, 12-98 13-1 13-6 13-39, 13-47, 13-59 14-1 14-4 14-18, 14-24, 14-45, 14-82 Introduction Newton s Law of Cooling Controlling

More information

Level 7 Post Graduate Diploma in Engineering Heat and mass transfer

Level 7 Post Graduate Diploma in Engineering Heat and mass transfer 9210-221 Level 7 Post Graduate Diploma in Engineering Heat and mass transfer 0 You should have the following for this examination one answer book non programmable calculator pen, pencil, drawing instruments

More information

TankExampleNov2016. Table of contents. Layout

TankExampleNov2016. Table of contents. Layout Table of contents Task... 2 Calculation of heat loss of storage tanks... 3 Properties ambient air Properties of air... 7 Heat transfer outside, roof Heat transfer in flow past a plane wall... 8 Properties

More information

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COURSE: MCE 524 DISCLAIMER The contents of this document are intended for practice and leaning purposes at the

More information

PROBLEM h fg ρ v ρ l σ 10 3 T sat (kj/kg) (kg/m 3 ) (N/m) (K)

PROBLEM h fg ρ v ρ l σ 10 3 T sat (kj/kg) (kg/m 3 ) (N/m) (K) PROBLEM 10.9 KNOWN: Fluids at 1 atm: mercury, ethanol, R-1. FIND: Critical heat flux; compare with value for water also at 1 atm. ASSUMPTIONS: (1) Steady-state conditions, () Nucleate pool boiling. PROPERTIES:

More information

Examination Heat Transfer

Examination Heat Transfer Examination Heat Transfer code: 4B680 date: June 13, 2008 time: 14.00-17.00 Note: There are 4 questions in total. The first one consists of independent subquestions. If possible and necessary, guide numbers

More information

ME 331 Homework Assignment #6

ME 331 Homework Assignment #6 ME 33 Homework Assignment #6 Problem Statement: ater at 30 o C flows through a long.85 cm diameter tube at a mass flow rate of 0.020 kg/s. Find: The mean velocity (u m ), maximum velocity (u MAX ), and

More information

PROBLEM ρ v (kg/m 3 ) ANALYSIS: The critical heat flux can be estimated by Eq with C = 0.

PROBLEM ρ v (kg/m 3 ) ANALYSIS: The critical heat flux can be estimated by Eq with C = 0. PROBLEM 10.10 KNOWN: Fluids at 1 atm: mercury, ethanol, R-14a. FIND: Critical heat flux; compare with value for water also at 1 atm. ASSUMPTIONS: (1) Steady-state conditions, () Nucleate pool boiling.

More information

Principles of Food and Bioprocess Engineering (FS 231) Exam 2 Part A -- Closed Book (50 points)

Principles of Food and Bioprocess Engineering (FS 231) Exam 2 Part A -- Closed Book (50 points) Principles of Food and Bioprocess Engineering (FS 231) Exam 2 Part A -- Closed Book (50 points) 1. Are the following statements true or false? (20 points) a. Thermal conductivity of a substance is a measure

More information

PROBLEM 8.3 ( ) p = kg m 1m s m 1000 m = kg s m = bar < P = N m 0.25 m 4 1m s = 1418 N m s = 1.

PROBLEM 8.3 ( ) p = kg m 1m s m 1000 m = kg s m = bar < P = N m 0.25 m 4 1m s = 1418 N m s = 1. PROBLEM 8.3 KNOWN: Temperature and velocity of water flow in a pipe of prescribed dimensions. FIND: Pressure drop and pump power requirement for (a) a smooth pipe, (b) a cast iron pipe with a clean surface,

More information

1. Nusselt number and Biot number are computed in a similar manner (=hd/k). What are the differences between them? When and why are each of them used?

1. Nusselt number and Biot number are computed in a similar manner (=hd/k). What are the differences between them? When and why are each of them used? 1. Nusselt number and Biot number are computed in a similar manner (=hd/k). What are the differences between them? When and why are each of them used?. During unsteady state heat transfer, can the temperature

More information

Chapter 10: Boiling and Condensation 1. Based on lecture by Yoav Peles, Mech. Aero. Nuc. Eng., RPI.

Chapter 10: Boiling and Condensation 1. Based on lecture by Yoav Peles, Mech. Aero. Nuc. Eng., RPI. Chapter 10: Boiling and Condensation 1 1 Based on lecture by Yoav Peles, Mech. Aero. Nuc. Eng., RPI. Objectives When you finish studying this chapter, you should be able to: Differentiate between evaporation

More information

Heat Transfer Convection

Heat Transfer Convection Heat ransfer Convection Previous lectures conduction: heat transfer without fluid motion oday (textbook nearly 00 pages) Convection: heat transfer with fluid motion Research methods different Natural Convection

More information

ELEC9712 High Voltage Systems. 1.2 Heat transfer from electrical equipment

ELEC9712 High Voltage Systems. 1.2 Heat transfer from electrical equipment ELEC9712 High Voltage Systems 1.2 Heat transfer from electrical equipment The basic equation governing heat transfer in an item of electrical equipment is the following incremental balance equation, with

More information

Specific heat capacity. Convective heat transfer coefficient. Thermal diffusivity. Lc ft, m Characteristic length (r for cylinder or sphere; for slab)

Specific heat capacity. Convective heat transfer coefficient. Thermal diffusivity. Lc ft, m Characteristic length (r for cylinder or sphere; for slab) Important Heat Transfer Parameters CBE 150A Midterm #3 Review Sheet General Parameters: q or or Heat transfer rate Heat flux (per unit area) Cp Specific heat capacity k Thermal conductivity h Convective

More information

Experiment 1. Measurement of Thermal Conductivity of a Metal (Brass) Bar

Experiment 1. Measurement of Thermal Conductivity of a Metal (Brass) Bar Experiment 1 Measurement of Thermal Conductivity of a Metal (Brass) Bar Introduction: Thermal conductivity is a measure of the ability of a substance to conduct heat, determined by the rate of heat flow

More information

Coolant. Circuits Chip

Coolant. Circuits Chip 1) A square isothermal chip is of width w=5 mm on a side and is mounted in a subtrate such that its side and back surfaces are well insulated, while the front surface is exposed to the flow of a coolant

More information

Convection. forced convection when the flow is caused by external means, such as by a fan, a pump, or atmospheric winds.

Convection. forced convection when the flow is caused by external means, such as by a fan, a pump, or atmospheric winds. Convection The convection heat transfer mode is comprised of two mechanisms. In addition to energy transfer due to random molecular motion (diffusion), energy is also transferred by the bulk, or macroscopic,

More information

Summary of Dimensionless Numbers of Fluid Mechanics and Heat Transfer

Summary of Dimensionless Numbers of Fluid Mechanics and Heat Transfer 1. Nusselt number Summary of Dimensionless Numbers of Fluid Mechanics and Heat Transfer Average Nusselt number: convective heat transfer Nu L = conductive heat transfer = hl where L is the characteristic

More information

Transport processes. 7. Semester Chemical Engineering Civil Engineering

Transport processes. 7. Semester Chemical Engineering Civil Engineering Transport processes 7. Semester Chemical Engineering Civil Engineering 1. Elementary Fluid Dynamics 2. Fluid Kinematics 3. Finite Control Volume Analysis 4. Differential Analysis of Fluid Flow 5. Viscous

More information

Thermal Unit Operation (ChEg3113)

Thermal Unit Operation (ChEg3113) Thermal Unit Operation (ChEg3113) Lecture 3- Examples on problems having different heat transfer modes Instructor: Mr. Tedla Yeshitila (M.Sc.) Today Review Examples Multimode heat transfer Heat exchanger

More information

OUTCOME 2 - TUTORIAL 1

OUTCOME 2 - TUTORIAL 1 Unit 4: Heat Transfer and Combustion Unit code: K/60/44 QCF level: 5 Credit value: 5 OUTCOME - TUTORIAL Heat transfer coefficients Dimensional analysis: dimensionless groups; Reynolds, Nusselt, Prandtl,

More information

MYcsvtu Notes HEAT TRANSFER BY CONVECTION

MYcsvtu Notes HEAT TRANSFER BY CONVECTION www.mycsvtunotes.in HEAT TRANSFER BY CONVECTION CONDUCTION Mechanism of heat transfer through a solid or fluid in the absence any fluid motion. CONVECTION Mechanism of heat transfer through a fluid in

More information

Heat Transfer Predictions for Carbon Dioxide in Boiling Through Fundamental Modelling Implementing a Combination of Nusselt Number Correlations

Heat Transfer Predictions for Carbon Dioxide in Boiling Through Fundamental Modelling Implementing a Combination of Nusselt Number Correlations Heat Transfer Predictions for Carbon Dioxide in Boiling Through Fundamental Modelling Implementing a Combination of Nusselt Number Correlations L. Makaum, P.v.Z. Venter and M. van Eldik Abstract Refrigerants

More information

Convection. U y. U u(y) T s. T y

Convection. U y. U u(y) T s. T y Convection Heat transfer in the presence of a fluid motion on a solid surface Various mechanisms at play in the fluid: - advection physical transport of the fluid - diffusion conduction in the fluid -

More information

Circle one: School of Mechanical Engineering Purdue University ME315 Heat and Mass Transfer. Exam #2. April 3, 2014

Circle one: School of Mechanical Engineering Purdue University ME315 Heat and Mass Transfer. Exam #2. April 3, 2014 Circle one: Div. 1 (12:30 pm, Prof. Choi) Div. 2 (9:30 am, Prof. Xu) School of Mechanical Engineering Purdue University ME315 Heat and Mass Transfer Exam #2 April 3, 2014 Instructions: Write your name

More information

Outlines. simple relations of fluid dynamics Boundary layer analysis. Important for basic understanding of convection heat transfer

Outlines. simple relations of fluid dynamics Boundary layer analysis. Important for basic understanding of convection heat transfer Forced Convection Outlines To examine the methods of calculating convection heat transfer (particularly, the ways of predicting the value of convection heat transfer coefficient, h) Convection heat transfer

More information

T718. c Dr. Md. Zahurul Haq (BUET) HX: Energy Balance and LMTD ME 307 (2018) 2/ 21 T793

T718. c Dr. Md. Zahurul Haq (BUET) HX: Energy Balance and LMTD ME 307 (2018) 2/ 21 T793 HX: Energy Balance and LMTD Dr. Md. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & Technology (BUET) Dhaka-000, Bangladesh http://zahurul.buet.ac.bd/

More information

Latest Heat Transfer

Latest Heat Transfer Latest Heat Transfer 1. Unit of thermal conductivity in M.K.S. units is (a) kcal/kg m2 C (b) kcal-m/hr m2 C (c) kcal/hr m2 C (d) kcal-m/hr C (e) kcal-m/m2 C. 2. Unit of thermal conductivity in S.I. units

More information

Heat Transfer. Solutions for Vol I _ Classroom Practice Questions. Chapter 1 Conduction

Heat Transfer. Solutions for Vol I _ Classroom Practice Questions. Chapter 1 Conduction Heat ransfer Solutions for Vol I _ lassroom Practice Questions hapter onduction r r r K K. ns: () ase (): Higher thermal conductive material is inside and lo thermal conductive material is outside K K

More information

Heat and Mass Transfer Prof. S.P. Sukhatme Department of Mechanical Engineering Indian Institute of Technology, Bombay

Heat and Mass Transfer Prof. S.P. Sukhatme Department of Mechanical Engineering Indian Institute of Technology, Bombay Heat and Mass Transfer Prof. S.P. Sukhatme Department of Mechanical Engineering Indian Institute of Technology, Bombay Lecture No. 18 Forced Convection-1 Welcome. We now begin our study of forced convection

More information

University of Rome Tor Vergata

University of Rome Tor Vergata University of Rome Tor Vergata Faculty of Engineering Department of Industrial Engineering THERMODYNAMIC AND HEAT TRANSFER HEAT TRANSFER dr. G. Bovesecchi gianluigi.bovesecchi@gmail.com 06-7259-727 (7249)

More information

C ONTENTS CHAPTER TWO HEAT CONDUCTION EQUATION 61 CHAPTER ONE BASICS OF HEAT TRANSFER 1 CHAPTER THREE STEADY HEAT CONDUCTION 127

C ONTENTS CHAPTER TWO HEAT CONDUCTION EQUATION 61 CHAPTER ONE BASICS OF HEAT TRANSFER 1 CHAPTER THREE STEADY HEAT CONDUCTION 127 C ONTENTS Preface xviii Nomenclature xxvi CHAPTER ONE BASICS OF HEAT TRANSFER 1 1-1 Thermodynamics and Heat Transfer 2 Application Areas of Heat Transfer 3 Historical Background 3 1-2 Engineering Heat

More information

Mechanical Engineering. Postal Correspondence Course HEAT TRANSFER. GATE, IES & PSUs

Mechanical Engineering. Postal Correspondence Course HEAT TRANSFER. GATE, IES & PSUs Heat Transfer-ME GATE, IES, PSU 1 SAMPLE STUDY MATERIAL Mechanical Engineering ME Postal Correspondence Course HEAT TRANSFER GATE, IES & PSUs Heat Transfer-ME GATE, IES, PSU 2 C O N T E N T 1. INTRODUCTION

More information

Convective Mass Transfer

Convective Mass Transfer Convective Mass Transfer Definition of convective mass transfer: The transport of material between a boundary surface and a moving fluid or between two immiscible moving fluids separated by a mobile interface

More information

Introduction to Heat and Mass Transfer. Week 14

Introduction to Heat and Mass Transfer. Week 14 Introduction to Heat and Mass Transfer Week 14 Next Topic Internal Flow» Velocity Boundary Layer Development» Thermal Boundary Layer Development» Energy Balance Velocity Boundary Layer Development Velocity

More information

MODULE CODE: ENGG08021 INTRODUCTION TO THERMOFLUIDS. Date: 15 January 2016 Time: 10:00 12:00

MODULE CODE: ENGG08021 INTRODUCTION TO THERMOFLUIDS. Date: 15 January 2016 Time: 10:00 12:00 School of Engineering & Computing Session 2015-16 Paisley Campus Trimester 1 MODULE CODE: ENGG08021 INTRODUCTION TO THERMOFLUIDS Date: 15 January 2016 Time: 10:00 12:00 Attempt FOUR QUESTIONS IN TOTAL

More information

Name: ME 315: Heat and Mass Transfer Spring 2008 EXAM 2 Tuesday, 18 March :00 to 8:00 PM

Name: ME 315: Heat and Mass Transfer Spring 2008 EXAM 2 Tuesday, 18 March :00 to 8:00 PM Name: ME 315: Heat and Mass Transfer Spring 2008 EXAM 2 Tuesday, 18 March 2008 7:00 to 8:00 PM Instructions: This is an open-book eam. You may refer to your course tetbook, your class notes and your graded

More information

Heat processes. Heat exchange

Heat processes. Heat exchange Heat processes Heat exchange Heat energy transported across a surface from higher temperature side to lower temperature side; it is a macroscopic measure of transported energies of molecular motions Temperature

More information

HEAT TRANSFER 1 INTRODUCTION AND BASIC CONCEPTS 5 2 CONDUCTION

HEAT TRANSFER 1 INTRODUCTION AND BASIC CONCEPTS 5 2 CONDUCTION HEAT TRANSFER 1 INTRODUCTION AND BASIC CONCEPTS 5 2 CONDUCTION 11 Fourier s Law of Heat Conduction, General Conduction Equation Based on Cartesian Coordinates, Heat Transfer Through a Wall, Composite Wall

More information

Heat Transfer Modeling using ANSYS FLUENT

Heat Transfer Modeling using ANSYS FLUENT Lecture 1 - Introduction 14.5 Release Heat Transfer Modeling using ANSYS FLUENT 2013 ANSYS, Inc. March 28, 2013 1 Release 14.5 Outline Modes of Heat Transfer Basic Heat Transfer Phenomena Conduction Convection

More information

PHYSICAL MECHANISM OF CONVECTION

PHYSICAL MECHANISM OF CONVECTION Tue 8:54:24 AM Slide Nr. 0 of 33 Slides PHYSICAL MECHANISM OF CONVECTION Heat transfer through a fluid is by convection in the presence of bulk fluid motion and by conduction in the absence of it. Chapter

More information

Chapter 3: Steady Heat Conduction. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University

Chapter 3: Steady Heat Conduction. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Chapter 3: Steady Heat Conduction Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Objectives When you finish studying this chapter, you should be able to: Understand the concept

More information

Introduction to Heat and Mass Transfer. Week 5

Introduction to Heat and Mass Transfer. Week 5 Introduction to Heat and Mass Transfer Week 5 Critical Resistance Thermal resistances due to conduction and convection in radial systems behave differently Depending on application, we want to either maximize

More information

Lectures on Applied Reactor Technology and Nuclear Power Safety. Lecture No 6

Lectures on Applied Reactor Technology and Nuclear Power Safety. Lecture No 6 Lectures on Nuclear Power Safety Lecture No 6 Title: Introduction to Thermal-Hydraulic Analysis of Nuclear Reactor Cores Department of Energy Technology KTH Spring 2005 Slide No 1 Outline of the Lecture

More information

FORMULA SHEET. General formulas:

FORMULA SHEET. General formulas: FORMULA SHEET You may use this formula sheet during the Advanced Transport Phenomena course and it should contain all formulas you need during this course. Note that the weeks are numbered from 1.1 to

More information

MECHANISM BEHIND FREE /NATURAL CONVECTION

MECHANISM BEHIND FREE /NATURAL CONVECTION CONVECTIVE HEAT TRANSFER By: Prof K. M. Joshi, Assi. Professor, MED, SSAS Institute of Technology, Surat. MECHANISM BEHIND FREE /NATURAL CONVECTION The stagnate layer of fluid in immediate vicinity of

More information

Chapter 3 NATURAL CONVECTION

Chapter 3 NATURAL CONVECTION Fundamentals of Thermal-Fluid Sciences, 3rd Edition Yunus A. Cengel, Robert H. Turner, John M. Cimbala McGraw-Hill, 2008 Chapter 3 NATURAL CONVECTION Mehmet Kanoglu Copyright The McGraw-Hill Companies,

More information

HEAT AND MASS TRANSFER. List of Experiments:

HEAT AND MASS TRANSFER. List of Experiments: HEAT AND MASS TRANSFER List of Experiments: Conduction Heat Transfer Unit 1. Investigation of Fourier Law for linear conduction of heat along a simple bar. 2. Study the conduction of heat along a composite

More information

Transient Heat Transfer Experiment. ME 331 Introduction to Heat Transfer. June 1 st, 2017

Transient Heat Transfer Experiment. ME 331 Introduction to Heat Transfer. June 1 st, 2017 Transient Heat Transfer Experiment ME 331 Introduction to Heat Transfer June 1 st, 2017 Abstract The lumped capacitance assumption for transient conduction was tested for three heated spheres; a gold plated

More information

Chapter 11: Heat Exchangers. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University

Chapter 11: Heat Exchangers. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Chapter 11: Heat Exchangers Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Objectives When you finish studying this chapter, you should be able to: Recognize numerous types of

More information

Introduction to Heat and Mass Transfer

Introduction to Heat and Mass Transfer Introduction to Heat and Mass Transfer Week 16 Merry X mas! Happy New Year 2019! Final Exam When? Thursday, January 10th What time? 3:10-5 pm Where? 91203 What? Lecture materials from Week 1 to 16 (before

More information

Convection Workshop. Academic Resource Center

Convection Workshop. Academic Resource Center Convection Workshop Academic Resource Center Presentation Outline Understanding the concepts Correlations External Convection (Chapter 7) Internal Convection (Chapter 8) Free Convection (Chapter 9) Solving

More information

Reg. No. : Question Paper Code: E3133 B.E./B.Tech. DEGREE EXAMINATION, APRIL/MAY 2010 Fourth Semester Mechanical Engineering ME2251 HEAT AND MASS TRANSFER (Regulation 2008) Time: Three hours Heat and mass

More information

Chapter 10: Steady Heat Conduction

Chapter 10: Steady Heat Conduction Chapter 0: Steady Heat Conduction In thermodynamics, we considered the amount of heat transfer as a system undergoes a process from one equilibrium state to another hermodynamics gives no indication of

More information

PROBLEM 7.2 1/3. (b) The local convection coefficient, Eq. 7.23, and heat flux at x = L are 1/2 1/3

PROBLEM 7.2 1/3. (b) The local convection coefficient, Eq. 7.23, and heat flux at x = L are 1/2 1/3 PROBLEM 7. KNOWN: Temperature and velocity of engine oil. Temperature and length of flat plate. FIND: (a) Velocity and thermal boundary layer thickness at trailing edge, (b) Heat flux and surface shear

More information

THERMAL DESIGN OF FALLING FILM EVAPORATOR

THERMAL DESIGN OF FALLING FILM EVAPORATOR YMCA Institute of Engineering, Faridabad, Haryana.., Dec 9-10, 006. THERMAL DESIGN OF FALLING FILM EVAPORATOR Ashik Patel 1, Manish purohit, C. R. Sonawane 3 1, Department of Mechanical Engineering Students,

More information

HEAT TRANSFER. Mechanisms of Heat Transfer: (1) Conduction

HEAT TRANSFER. Mechanisms of Heat Transfer: (1) Conduction HEAT TRANSFER Mechanisms of Heat Transfer: (1) Conduction where Q is the amount of heat, Btu, transferred in time t, h k is the thermal conductivity, Btu/[h ft 2 ( o F/ft)] A is the area of heat transfer

More information

ECE309 INTRODUCTION TO THERMODYNAMICS & HEAT TRANSFER. 10 August 2005

ECE309 INTRODUCTION TO THERMODYNAMICS & HEAT TRANSFER. 10 August 2005 ECE309 INTRODUCTION TO THERMODYNAMICS & HEAT TRANSFER 0 August 2005 Final Examination R. Culham & M. Bahrami This is a 2 - /2 hour, closed-book examination. You are permitted to use one 8.5 in. in. crib

More information

SEM-2016(03)-II MECHANICAL ENGINEERING. Paper -11. Please read each of the following instructions carefully before. attempting questions.

SEM-2016(03)-II MECHANICAL ENGINEERING. Paper -11. Please read each of the following instructions carefully before. attempting questions. Roll No. Candidate should write his/her Roll No. here. Total No. of Questions : 7 No. of Printed Pages : 8 SEM-2016(03)-II MECHANICAL ENGINEERING Paper -11 Time : 3 Hours ] [ Total Marks : 300 Instructions

More information

HEAT TRANSFER BY CONVECTION. Dr. Şaziye Balku 1

HEAT TRANSFER BY CONVECTION. Dr. Şaziye Balku 1 HEAT TRANSFER BY CONVECTION Dr. Şaziye Balku 1 CONDUCTION Mechanism of heat transfer through a solid or fluid in the absence any fluid motion. CONVECTION Mechanism of heat transfer through a fluid in the

More information

DESIGN OF A SHELL AND TUBE HEAT EXCHANGER

DESIGN OF A SHELL AND TUBE HEAT EXCHANGER DESIGN OF A SHELL AND TUBE HEAT EXCHANGER Swarnotpal Kashyap Department of Chemical Engineering, IIT Guwahati, Assam, India 781039 ABSTRACT Often, in process industries the feed stream has to be preheated

More information

Principles of Convection

Principles of Convection Principles of Convection Point Conduction & convection are similar both require the presence of a material medium. But convection requires the presence of fluid motion. Heat transfer through the: Solid

More information

: HEAT TRANSFER & EVAPORATION COURSE CODE : 4072 COURSE CATEGORY : B PERIODS/ WEEK : 5 PERIODS/ SEMESTER : 70 CREDIT : 5 TIME SCHEDULE

: HEAT TRANSFER & EVAPORATION COURSE CODE : 4072 COURSE CATEGORY : B PERIODS/ WEEK : 5 PERIODS/ SEMESTER : 70 CREDIT : 5 TIME SCHEDULE COURSE TITLE : HEAT TRANSFER & EVAPORATION COURSE CODE : 4072 COURSE CATEGORY : B PERIODS/ WEEK : 5 PERIODS/ SEMESTER : 70 CREDIT : 5 TIME SCHEDULE MODULE TOPIC PERIODS 1 Conduction,Fourier law,variation

More information

Lecture 30 Review of Fluid Flow and Heat Transfer

Lecture 30 Review of Fluid Flow and Heat Transfer Objectives In this lecture you will learn the following We shall summarise the principles used in fluid mechanics and heat transfer. It is assumed that the student has already been exposed to courses in

More information

PHYS102 Previous Exam Problems. Temperature, Heat & The First Law of Thermodynamics

PHYS102 Previous Exam Problems. Temperature, Heat & The First Law of Thermodynamics PHYS102 Previous Exam Problems CHAPTER 18 Temperature, Heat & The First Law of Thermodynamics Equilibrium & temperature scales Thermal expansion Exchange of heat First law of thermodynamics Heat conduction

More information

INSTRUCTOR: PM DR MAZLAN ABDUL WAHID

INSTRUCTOR: PM DR MAZLAN ABDUL WAHID SMJ 4463: HEAT TRANSFER INSTRUCTOR: PM DR MAZLAN ABDUL WAHID http://www.fkm.utm.my/~mazlan TEXT: Introduction to Heat Transfer by Incropera, DeWitt, Bergman, Lavine 5 th Edition, John Wiley and Sons DR

More information

Forced Convection: Inside Pipe HANNA ILYANI ZULHAIMI

Forced Convection: Inside Pipe HANNA ILYANI ZULHAIMI + Forced Convection: Inside Pipe HANNA ILYANI ZULHAIMI + OUTLINE u Introduction and Dimensionless Numbers u Heat Transfer Coefficient for Laminar Flow inside a Pipe u Heat Transfer Coefficient for Turbulent

More information

Problem 4.3. Problem 4.4

Problem 4.3. Problem 4.4 Problem 4.3 Problem 4.4 Problem 4.5 Problem 4.6 Problem 4.7 This is forced convection flow over a streamlined body. Viscous (velocity) boundary layer approximations can be made if the Reynolds number Re

More information

Phone: , For Educational Use. SOFTbank E-Book Center, Tehran. Fundamentals of Heat Transfer. René Reyes Mazzoco

Phone: , For Educational Use. SOFTbank E-Book Center, Tehran. Fundamentals of Heat Transfer. René Reyes Mazzoco 8 Fundamentals of Heat Transfer René Reyes Mazzoco Universidad de las Américas Puebla, Cholula, Mexico 1 HEAT TRANSFER MECHANISMS 1.1 Conduction Conduction heat transfer is explained through the molecular

More information

طراحی مبدل های حرارتی مهدي کریمی ترم بهار HEAT TRANSFER CALCULATIONS

طراحی مبدل های حرارتی مهدي کریمی ترم بهار HEAT TRANSFER CALCULATIONS طراحی مبدل های حرارتی مهدي کریمی ترم بهار 96-97 HEAT TRANSFER CALCULATIONS ١ TEMPERATURE DIFFERENCE For any transfer the driving force is needed General heat transfer equation : Q = U.A. T What T should

More information

ECE309 INTRODUCTION TO THERMODYNAMICS & HEAT TRANSFER. 3 August 2004

ECE309 INTRODUCTION TO THERMODYNAMICS & HEAT TRANSFER. 3 August 2004 ECE309 INTRODUCTION TO THERMODYNAMICS & HEAT TRANSFER 3 August 004 Final Examination R. Culham This is a 3 hour, closed-book examination. You are permitted to use one 8.5 in. in. crib sheet (both sides),

More information

INTRODUCTION: Shell and tube heat exchangers are one of the most common equipment found in all plants. How it works?

INTRODUCTION: Shell and tube heat exchangers are one of the most common equipment found in all plants. How it works? HEAT EXCHANGERS 1 INTRODUCTION: Shell and tube heat exchangers are one of the most common equipment found in all plants How it works? 2 WHAT ARE THEY USED FOR? Classification according to service. Heat

More information

Conduction Heat Transfer. Fourier Law of Heat Conduction. Thermal Resistance Networks. Resistances in Series. x=l Q x+ Dx. insulated x+ Dx.

Conduction Heat Transfer. Fourier Law of Heat Conduction. Thermal Resistance Networks. Resistances in Series. x=l Q x+ Dx. insulated x+ Dx. Conduction Heat Transfer Reading Problems 17-1 17-6 17-35, 17-57, 17-68, 17-81, 17-88, 17-110 18-1 18-2 18-14, 18-20, 18-34, 18-52, 18-80, 18-104 Fourier Law of Heat Conduction insulated x+ Dx x=l Q x+

More information

ENGR Heat Transfer II

ENGR Heat Transfer II ENGR 7901 - Heat Transfer II Convective Heat Transfer 1 Introduction In this portion of the course we will examine convection heat transfer principles. We are now interested in how to predict the value

More information

The Research of Heat Transfer Area for 55/19 Steam Generator

The Research of Heat Transfer Area for 55/19 Steam Generator Journal of Power and Energy Engineering, 205, 3, 47-422 Published Online April 205 in SciRes. http://www.scirp.org/journal/jpee http://dx.doi.org/0.4236/jpee.205.34056 The Research of Heat Transfer Area

More information

23 1 TYPES OF HEAT EXCHANGERS

23 1 TYPES OF HEAT EXCHANGERS cen5426_ch23.qxd /26/04 9:42 AM Page 032 032 FUNDAMENTALS OF THERMAL-FLUID SCIENCES 23 TYPES OF HEAT EXCHANGERS Different heat transfer applications require different types of hardware different configurations

More information

FINAL Examination Paper (COVER PAGE) Programme : BACHELOR OF ENGINEERING (HONS) IN MECHANICAL ENGINEERING PROGRAMME (BMEGI)

FINAL Examination Paper (COVER PAGE) Programme : BACHELOR OF ENGINEERING (HONS) IN MECHANICAL ENGINEERING PROGRAMME (BMEGI) MEE0 (F) / Page of Session : August 0 FINA Examination Paper (COVER PAGE) Programme : BACHEOR OF ENGINEERING (HONS) IN MECHANICA ENGINEERING PROGRAMME (BMEGI) Course : MEE0 : Combustion, Heat and Mass

More information

MECH 375, Heat Transfer Handout #5: Unsteady Conduction

MECH 375, Heat Transfer Handout #5: Unsteady Conduction 1 MECH 375, Heat Transfer Handout #5: Unsteady Conduction Amir Maleki, Fall 2018 2 T H I S PA P E R P R O P O S E D A C A N C E R T R E AT M E N T T H AT U S E S N A N O PA R T I - C L E S W I T H T U

More information

Introduction to Heat and Mass Transfer. Week 14

Introduction to Heat and Mass Transfer. Week 14 Introduction to Heat and Mass Transfer Week 14 HW # 7 prob. 2 Hot water at 50C flows through a steel pipe (thermal conductivity 14 W/m-K) of 100 mm outside diameter and 8 mm wall thickness. During winter,

More information

PHYSICAL MECHANISM OF NATURAL CONVECTION

PHYSICAL MECHANISM OF NATURAL CONVECTION 1 NATURAL CONVECTION In this chapter, we consider natural convection, where any fluid motion occurs by natural means such as buoyancy. The fluid motion in forced convection is quite noticeable, since a

More information

Autumn 2005 THERMODYNAMICS. Time: 3 Hours

Autumn 2005 THERMODYNAMICS. Time: 3 Hours CORK INSTITUTE OF TECHNOOGY Bachelor of Engineering (Honours) in Mechanical Engineering Stage 3 (Bachelor of Engineering in Mechanical Engineering Stage 3) (NFQ evel 8) Autumn 2005 THERMODYNAMICS Time:

More information

Overall Heat Transfer Coefficient

Overall Heat Transfer Coefficient Overall Heat Transfer Coefficient A heat exchanger typically involves two flowing fluids separated by a solid wall. Heat is first transferred from the hot fluid to the wall by convection, through the wall

More information

Chapter 7: External Forced Convection. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University

Chapter 7: External Forced Convection. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Chapter 7: External Forced Convection Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Objectives When you finish studying this chapter, you should be able to: Distinguish between

More information

Conduction Heat Transfer. Fourier Law of Heat Conduction. x=l Q x+ Dx. insulated x+ Dx. x x. x=0 Q x A

Conduction Heat Transfer. Fourier Law of Heat Conduction. x=l Q x+ Dx. insulated x+ Dx. x x. x=0 Q x A Conduction Heat Transfer Reading Problems 10-1 10-6 10-20, 10-48, 10-59, 10-70, 10-75, 10-92 10-117, 10-123, 10-151, 10-156, 10-162 11-1 11-2 11-14, 11-20, 11-36, 11-41, 11-46, 11-53, 11-104 Fourier Law

More information

HEAT AND MASS TRANSFER. Subject Code : 10ME63 IA Marks : 25 Hours/Week : 04 Exam Hours : 03 Total Hours : 52 Exam Marks : 100

HEAT AND MASS TRANSFER. Subject Code : 10ME63 IA Marks : 25 Hours/Week : 04 Exam Hours : 03 Total Hours : 52 Exam Marks : 100 HEAT AND MASS TRANSFER Subject Code : 10ME63 IA Marks : 25 Hours/Week : 04 Exam Hours : 03 Total Hours : 52 Exam Marks : 100 PART A UNIT - 1 Introductory Concepts and Definitions: Modes of heat transfer:

More information

ME6512-THERMAL ENGINEERING LAB-II VARUVAN VADIVELAN INSTITUTE OF TECHNOLOGY DHARMAPURI DEPARTMENT OF MECHANICAL ENGINEERING

ME6512-THERMAL ENGINEERING LAB-II VARUVAN VADIVELAN INSTITUTE OF TECHNOLOGY DHARMAPURI DEPARTMENT OF MECHANICAL ENGINEERING VARUVAN VADIVELAN INSTITUTE OF TECHNOLOGY DHARMAPURI 636 703 DEPARTMENT OF MECHANICAL ENGINEERING REG NO THERMAL ENGINEERING II LAB MANUAL NAME SUBJECT CODE\TITLE ME 6512 - THERMAL ENGINEERING LABORATORY

More information